Cino F700BT, F600BT Wireless Imager Reference Manual

WIRELESS IMAGER
Reference Manual
International Edition, Rev. A1
Wireless FuzzyScan
Reference Manual
Revision History
Rev. No.
Released Date
Rev.A
Oct. 16, 2009
Rev.A1
Oct. 22, 2009
Description
First Release
Page 6 Revise “Clone” function operation method.
Page 68 Add “Save Configuration” and “Master Default” quick set commands.
© Copyright Cino Group
© Copyright PC Worth Int’l Co., Ltd
Cino makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranty of
merchantability and fitness for any particular purpose. Cino shall not be liable for errors contained herein or for incidental
consequential damages in connection with the furnishing, performance, or use of this publication. This publication contains
proprietary information that is protected by copyright. All rights are reserved. No part of this publication may be photocopied,
reproduced or translated into any language, in any forms, in an electronic retrieval system or otherwise, without prior written
permission of Cino. All product information and specifications shown in this document may be changed without prior notice.
Warranty
Wireless FuzzyScan
Reference Manual
Cino warrants its products against defects in workmanship and materials from the date of shipment, provided that the
product is operated under normal and proper conditions. The warranty provisions and durations are furnished by different
warranty programs. The above warranty does not apply to any product which has been (i) misused; (ii) damaged by accident
or negligence; (iii) modified or altered by the purchaser or other party; (iv) repaired or tampered by unauthorized
representatives; (v) operated or stored beyond the specified operational and environmental parameters; (vi) applied
software, accessories or parts are not supplied by Cino; (vii) damaged by circumstances out of Cino’s control, such as, but
not limited to, lightning or fluctuation in electrical power. Any defective product must follow the warranty program and RMA
procedures to return Cino for inspection.
Regulatory
FCC part 15B, FCC part 15C
EN55022, EN55024, EN60950-1, EN301 489-1 & 489-17, EN300 328
CNS13438, CNS14336
LP0002
MIC T401
LED Eye Safety
IEC60825-1, EN60825-1
Table of Contents
Getting Started
Getting Familiar with Your FuzzyScan
Preparation before Using
Decide Your Radio Link Mode
Using FuzzyScan in PAIR Mode
Using FuzzyScan in PICO Mode
Using FuzzyScan in HID Mode
Using FuzzyScan in SPP Mode
Out-of-range Scanning/Presentation Scanning/Paging Function
Batch Scanning (Inventory Mode)
1
2
3
4
5
7
8
10
11
Wireless FuzzyScan
Reference Manual
Configure Your FuzzyScan
Bar Code Programming Manual
Programming Procedures
Host Interface Selection
Symbology Reading Control
Keyboard Interface Control
Serial Interface Control
Wand/Laser Emulation Control
Operation Control
Condensed DataWizard
13
14
18
19
37
41
44
45
55
Appendix
Symbology ID Table
Keyboard Function Code Table
ASCII Input Shortcut
Link Mode Quick Set/Operation Mode Quick Set
Host Interface Quick Set
Option Codes
System Commands
62
63
64
65
66
67
68
Getting Started
Getting Familiar with Your FuzzyScan
Thank you for choosing Cino FuzzyScan Bluetooth Cordless Image Scanner. Powered by the combination of cutting-edge
FuzzyScan 2.0 Imaging Technology and Bluetooth 2.1 EDR wireless technology, it not only provides outstanding reading
performance, but also delivers the convenience and freedom of mobility. This document provides a quick reference for
installation and operation purposes. The complete documentation is available at www.cino.com.tw.
F700BT Series Scanner
HB2110 Smart Cradle (Base)
Center Indicator
Side Indicators
Paging/Reset Button
Host Interface Port
DC Power Jack
Wireless FuzzyScan
Reference Manual
F600BT Series Scanner
Link Indicator
Status Indicator
Beeper
Scan Window
Trigger
Reset Button
Battery Cavity
End Cap
HB2100 Charging Cradle (Base)
Power Indicator
Reserved
Reserved
DC Power Jack
1
Getting Started
Preparation before Using
Install the Battery
Ensure the battery contacts of the battery pack are facing the charging contacts inside
the battery cavity.
Slide the battery pack into the battery cavity until hearing a click sound before locking it
with the end cap. The scanner will give 4 beeps when the battery pack is installed
properly if the battery pack still has power.
Secure the end cap with the screw provided, and make sure the end cap is secured
properly before using the scanner.
Charging the Battery
There are 4 different power plugs in your power supply kit. Choose the appropriate local
plug and slot it onto the power adapter cavity until it is locked.
Wireless FuzzyScan
Reference Manual
Plug the AC power plug into the appropriate AC wall socket.
Plug the DC power cord of the power supply unit into the DC power jack of the cradle.
The smart cradle will issue the power on beeps and the center indicator will give one
blue blink. If you use the charging cradle, please check the power indicator of the
charging cradle turns steady blue.
Place the scanner on the cradle. The status indicator of scanner will turn steady red if
the battery is not fully charged. When the battery is fully charged, the status indicator of
scanner will flash green at regular interval.
Please charge the new battery pack for 8 hours prior to the first use.
2
Getting Started
Decide Your Radio Link Mode
The FuzzyScan Bluetooth image scanner provides several radio link modes to communicate with most host devices. When
the Bluetooth-enabled host device is not available, it can work with the smart cradle in PAIR mode (one to one connection) or
PICO mode (multiple connections) to provide a plug-and-play cordless migration of your existing non-Bluetooth-enabled IT
assets. Moreover, you are also able to use the scanner to work with Bluetooth-enabled host devices via SPP master/slave
modes and HID mode.
After losing the radio link, the scanner is capable of resuming the radio connection automatically while it returns to the
communication coverage. But please note that this feature is not available in SPP slave mode. If you would like to change
the radio link mode, you have to scan the “Uninstall” command to revert the scanner to uninstall state.
PAIR Mode
If the Bluetooth device is not available in your existing system, this is the simplest plug-and-play solution. In this mode, one
scanner can only work with one smart cradle. The smart cradle not only provides the Bluetooth radio link with the scanner,
but also offers the legacy cabled interfaces to the host device, including USB HID, USB COM, PS/2(DOS/V) Keyboard
Wedge and RS232 Serial.
Wireless FuzzyScan
Reference Manual
PICO Mode
For the requirement of multiple connections, up to 7 scanners can be connected to one smart cradle concurrently. If you
would like to un-pair all paired scanners and smart cradle, you can simply press and hold the paging/reset button of the
smart cradle for over 3 seconds. If you just want to un-pair part of the paired scanners, please take those paired scanners to
scan the “Uninstall” command one by one.
HID Mode
Through the most helpful HID service, the scanner can work like a Bluetooth keyboard. In this mode, the scanner is
discoverable by the radio connection request issued by a remote host device. For security purpose, you will be requested to
input the PIN Code to establish the Bluetooth connection in most time.
SPP Master/Slave Mode
Through the standard SPP service, the scanner can work like a serial input device. In SPP master mode, the scanner
initiates the radio connection request to a remote slave device. In SPP slave mode, the scanner is discoverable by the radio
connection request issued by a remote master device.
3
Getting Started
Using FuzzyScan in PAIR Mode
Ensure the battery is fully charged. You may refer to the section of Preparations before Using for details.
Please choose your desired interface cable, then plug it into the host interface port of the smart cradle and connect it to
the host device.
USB
PS/2
RS232
Turn on the power of your host device.
Please note that the scanner has been pre-paired already, if the scanner is shipped together with the smart cradle. You
will see the link indicator of scanner gives 1 blue blink per 2.5 seconds and the middle indicator of smart cradle turns
steady blue. If the scanner and smart cradle just give alternating red and green blinks (in “Uninstall” state), please
follow steps 5-6 to establish the connection between the scanner and the smart cradle.
Wireless FuzzyScan
Reference Manual
Scan “PAIR mode” command. The status indicator of scanner will turn steady red.
Uninstall
PAIR Mode
Place the scanner on the smart cradle, then you will hear one short beep to indicate the pairing process is activated. The
scanner will give continuous short clicks and the link indicator of scanner will flash blue quickly during the pairing process.
When you hear 4 beeps in ascending tone, the pairing process is completed. You will see the link indicator of scanner
giving 1 blue blink per 2.5 seconds and the center indicator of the smart cradle turning steady blue.
If the scanner pairing process failed or it’s not placed on the smart cradle within 20 seconds, you will hear 2 “Di-do Di-do”
beeps to indicate pair failure, the scanner will return to uninstall state automatically.
Scan the corresponding host interface quick set command to complete the installation.
The default host interface of smart cradle is preset to USB HID. If you want to set the host interface to USB COM, you have to
install the USB virtual COM driver into your host device before using the scanner. Please visit the CINO website to download
the software driver.
4
Getting Started
Using FuzzyScan in PICO Mode
Ensure the battery is fully charged and choose your desired interface cable, then plug it into the host interface port of the
smart cradle and connect it to the host device.
USB
PS/2
RS232
Turn on the power of your host device.
Ensure the side indicators of the smart cradle give alternative red and green blinks (in “Uninstall” state). If the smart
cradle is paired with other scanners, you can press and hold the paging/reset button for over 3 seconds to un-pair all
paired scanners. Then the smart cradle will return to uninstall state automatically.
Prepare the scanners you desire to pair with smart cradle. Ensure the status indicator of each scanner give alternative
red and green blinks (in “Uninstall” state). If the scanner is not in uninstall state, please scan the “Uninstall” command to
un-pair the scanner. Then scan the “PICO mode” command, and the status indicator of scanner will turn steady red.
Wireless FuzzyScan
Reference Manual
Uninstall
PICO Mode
Place the scanner on the smart cradle, then you will hear one short beep to indicate the pairing process is activated. The
scanner will give continuous short clicks and the link indicator of scanner will flash blue quickly during the pairing process.
When you hear 4 beeps in ascending tone, the pairing process is completed. You will see the link indicator of scanner
giving 1 blue blink per 2.5 seconds, the center indicator of the smart cradle turning steady blue and its side indicators
turning steady green.
If the scanner pairing process failed or it’s not placed on the smart cradle within 20 seconds, you will hear 2 “Di-do Di-do”
beeps to indicate pair failure, the scanner will return to uninstall state automatically.
Scan the corresponding host interface quick set command to complete the installation.
Please follow the same procedures to pair the other scanners with the smart cradle.
For user’s convenience, the smart cradle will automatically assign the ID numbers to each scanner. After completed all
pairing processes, you can scan the “System Information” command to check the assigned ID number of each scanner.
5
Getting Started
Clone Function
For the user’s convenience, the clone function will help you to clone the host interface related parameters (please refer to
following table for details) from one of the paired scanners to the rest of paired scanners under PICO mode. You can use
one of the paired scanners to set the host interface related parameters first and then scan “Save Configuration” command.
After that, please take the other paired scanners to scan “Clone” command one by one to clone the host interface related
parameters.
Please ensure to keep those paired scanners in connected status when you use the “Clone” function. Because the host
interface related parameters can’t be cloned to the paired scanner in disconnected status.
Save Configuration
Clone
The below host interface related parameters will be impacted by clone function:
Data Transmission Parameter
Serial Interface Control
Field Delimiter
Handshaking Protocol
Data Transmission Format
Intermessage Delay
Host Interface Control
Interfunction Delay
Wireless FuzzyScan
Reference Manual
Host interface Selection
Intercharacter Delay
Keyboard Interface Control
Baud Rate
Keyboard Layout
Data Frame
Intermessage Delay
Time Out Control
Interfunction Delay
Wand Emulation Control
Intercharacter Delay
Output Polarity
Caps Lock Control
Initial Signal State
Caps Lock Release Control
Margin Time
Function Key Emulation
Module Time
Key Pad Emulation
Narrow/Wide Ratio
Upper/Lower Case
Code39 Emulation
6
Getting Started
Using FuzzyScan in HID Mode
Ensure the battery is fully charged. Power on the scanner within radio range and ensure the status indicator of scanner
gives alternating red and green blinks (in “Uninstall” state). If the scanner is not in uninstall state, please scan the
“Uninstall” command first. Then scan the “HID Mode” command, and the link indicator of scanner will give 3 blue blinks
per 2 seconds.
Uninstall
HID Mode
Execute the Bluetooth Discovery procedure to find all available Bluetooth devices in your remote host. You will see ‘’CINO
FxxxBT-xxxx’’ is shown in the list if the scanner is successfully discovered already.
Double click the “CINO FxxxBT-xxxx” in the discovered Bluetooth device list. If the PIN Code or Passkey is requested for
security connection, please enter “00000000” (default setting). You will see “Keyboard on CINO FxxxBT-xxxx”, and
double click this HID service to establish the connection between the scanner and the remote host device.
Wireless FuzzyScan
Reference Manual
The scanner will give 4 beeps in ascending tone to indicate the radio is connected. At the same time, the link indicator of
scanner will give 1 blue blink per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner is not connected to the host device within 1 minute after scanning the “HID Mode”
command, the scanner will go to sleep automatically. You just need to press the trigger to wake up the scanner to
continue the installation.
1. The installation procedures vary on different remote host devices, operation systems and the Bluetooth software driver.
Please consult your professional IT consultant to obtain necessary support if any problem has been encountered during
the installation processes.
2. While using HID mode, beware of potential error in the data transmitted at the same time when radio link quality is poor.
You are suggested to use the scanner under the communication coverage all the times.
7
Getting Started
Using FuzzyScan in SPP Mode
Establish SPP Master Connection
Ensure the battery is fully charged. Please go to the folder of “Hardware” located in Bluetooth Advanced Setting of the
remote host device to check its device MAC address. Then prepare a 12-character Code 128 barcode of the remote host
device MAC address, or follow the step 4 to input MAC address by scanning 12 option codes.
Ensure a virtual COM port is available in your remote host for connecting the scanner. If not, please go to the folder of
“Local Services” located in Bluetooth Advanced Setting. Click the “Add Serial Services” to add one more Bluetooth
COM port.
Power on the scanner within radio range and ensure the status indicator of scanner gives alternating red and green
blinks (in “Uninstall” state). If the scanner is not in uninstall state, please scan the “Uninstall” command first. Then scan
the “SPP Master Mode” command, and the status indicator of scanner will turn steady red.
Wireless FuzzyScan
Reference Manual
Uninstall
SPP Master Mode
Scan a 12-character MAC address barcode, or scan 12 option codes and “FIN” command to confirm your inputs. The
scanner will give continuous short clicks and the link indicator of the scanner will flash blue quickly during the radio
connecting process. If the PIN Code or Passkey is requested for security connection, please enter “00000000” (default
setting).
The scanner will give 4 beeps in ascending tone to indicate the radio is connected. At the same time, the link indicator of
scanner will give 1 blue blink per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner failed to connect to the host device within 30 seconds, the link indicator will give 3 blue
blinks per 2 seconds. But the scanner is still continuing to discover the host device for another 30 seconds before go to
sleep. In the interim, you still can scan “Uninstall” command to revert the scanner to uninstall state. If the scanner goes to
sleep already, you just need to press the trigger to wake up the scanner to continue the installation.
The installation procedures vary on different remote host devices, operating systems and the Bluetooth software driver.
Please consult your professional IT consultant to obtain necessary support if any problem has been encountered during the
installation processes.
8
Getting Started
Establish SPP Slave Connection
Ensure the battery is fully charged and a virtual COM port is available in your remote host for connecting the scanner. If
not, please go to the folder of “Client Applications” located in Bluetooth Advanced Setting. Click the “Add COM Port” to
add one more Bluetooth COM port.
Power on the scanner within radio range and ensure the status indicator of scanner gives alternating red and green
blinks (in “Uninstall” state). If the scanner is not in uninstall state, please scan the “Uninstall” command first. Then scan
the “SPP Slave Mode” command, and the link indicator of scanner will give 3 blue blinks per 2 seconds.
Uninstall
SPP Slave Mode
Execute the Bluetooth Discovery procedure to find all available Bluetooth device list in your remote host. You will see
‘’CINO FxxxBT-xxxx’’ is shown in the list if the scanner is successfully discovered already.
Wireless FuzzyScan
Reference Manual
Double click the “CINO FxxxBT-xxxx” on the discovered Bluetooth devices. If the PIN Code or Passkey is requested for
security connection, please enter “00000000” (default setting). You will see “Serial Port on CINO FxxxBT-xxxx”, and
double click this SPP service to establish the connection between the scanner and the remote host device.
The scanner will give 4 beeps in ascending tone to indicate the radio is connected. At the same time, the link indicator of
scanner will give 1 blue blink per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner is not connected to the host device within 1 minute, the scanner will go to sleep. You can
press the trigger to wake up the scanner to continue the installation.
The installation procedures vary on different remote host devices, operating systems and the Bluetooth software drivers.
Please consult your professional IT consultant to obtain necessary support if any problem has been encountered during the
installation processes.
9
Getting Started
Out-of-range Scanning
When the radio is connected between the scanner and the remote host device, the scanner will transmit each scanned data
right after scanning the barcode. However, the scanner is preset for unable to scan any barcode data when it loses the radio
connection with the remote host device.
If you enable the out-of-range scanning function, the scanner is able to continue scanning barcode data while it is out of
working range. All scanned data will be temporarily stored into the memory buffer until radio link resumed.
Enable Out-of-range Scannning
Disable Out-of-range Scanning ◆
In case of the scanner is out of working range, you will hear 4 beeps in descending tone to indicate the radio connection lost.
The link indicator of scanner will give 3 blue blinks per 2 seconds. Once the scanner is back to working range, you will hear 4
beeps in ascending tone to indicate the radio connection rebuilt and the scanner will give 1 blue blink per 2.5 seconds. At the
same time, all stored scanned data will be transmitted automatically right after the radio link is resumed.
Presentation Scanning
Wireless FuzzyScan
Reference Manual
The Presentation Scanning is designed for hand-free applications for user’s convenience. If the “Presentation Scanning
Auto-sense” function is enabled, the scanner is capable of automatically switching to presentation mode when you place it
onto the SmartStand or cradle.
Enable Presentation Scanning Auto-sense
Disable Presentation Scanning Auto-sense ◆
Paging Function
The paging function is helpful for you to locate the paired smart cradle or scanner. If you would like to page the paired smart
cradle, you can scan “Paging” command. If you would like to page the paired scanner, you can press the paging/rest button
of the smart cradle no longer than 3 seconds.
Paging
Paging/Reset Button
10
Getting Started
Batch Scanning (Inventory Mode)
Thanks to the specially designed Batch Scanning function, the scanner is capable of storing the barcode data up to 20,000
EAN-13 labels. It is an ideal cost-saving solution for inventory applications.
Once you scan the “Enter Batch Scanning” command to activate this function, all scanned barcode data will be stored into
the memory storage, and the status indicator of scanner will give green blink at regular interval during batch scanning. You
can scan and store the barcode data till the memory storage is full. If the storage is full, you will hear 2 long beeps and the
status indicator will give 2 red blinks to indicate out of storage. To terminate the batch scanning, please scan the “Exit Batch
Scanning” command.
Enter Batch Scanning
Exit Batching Scanning
How to Transmit Stored Data
The scanner is preset to scan the “Transmit Stored Data” command to transmit all stored data. During the transmission
process, the scanner will give continuous short clicks and blue blinks. Then the scanner will give two short beeps after data
transmission is completed.
Wireless FuzzyScan
Reference Manual
Transmit Stored Data
But you are still able to set the scanner to transmit the stored data by placing the scanner onto the cradle as well.
Transmit Stored Data by Scanning
Barcode Command ◆
Transmit Stored Data by Scanning Barcode
or Placing Scanner onto Cradle
Transmit Stored Data by
Placing Scanner onto Cradle
The scanner is preset to keep all the stored data until you scan the “Clear All Stored Data” command. But you are still able to
change the setting to “Auto Delete Stored Data after Transmission” as well.
Clear All Stored Data
11
Getting Started
Auto Delete Stored Data
after Transmission
Keep Stored Data after
Transmission ◆
If you scanned a wrong barcode, the “Delete Last Scanned Data’’ command is helpful to recover mistake. By scanning the
‘’Delete Last Scanned Data’’ command, the last stored data can be deleted.
Delete Last Scanned Data
Using Quantity Feature
If you want to input the quantity information of barcode data, you can enter the quantity from 1 to 9999 by scanning the
quantity barcodes right after you scanned the barcode data. The quantity information will be stored into the memory storage
together with the barcode data.
Quantity 0
Quantity 5
Wireless FuzzyScan
Reference Manual
Quantity 3
Quantity 8
Quantity 1
Quantity 6
Quantity 4
Quantity 9
Quantity 2
Quantity 7
There are two ways to output the stored barcode data and quantity information. Please refer to following for details:
Stored data is transmitted as many times as the quantity indicated.
Stored data is transmitted together with quantity information in two fields. Please scan “Enable Quantity Field
Transmission” command to enable this function. The preset delimiter is “，“, but you are able to choose your desired one
from FuzzyScan Wireless Reference Manual for details.
Disable Quantity Field Transmission ◆
Enable Quantity Field Transmission
12
Configure Your FuzzyScan
Bar Code Programming Menu
The FuzzyScan bar code commands are specially designed
Proprietary bar code labels which allow you to set the
FuzzyScan internal programming parameters. There are
System Command, Family Code and Option Code for
programming purpose.
System Command
The System Command is the highest level bar code
command which directs FuzzyScan to perform immediate
operations, such as entering programming mode
(PROGRAM), exiting programming mode (EXIT), listing
system information (SYSLIST), recovering to factory
preset configurations (M_DEFAULT), and so on. Please
note that all system commands will take a few seconds to
complete the operations. User must wait for the
completion beeps before scanning another bar code.
Wireless FuzzyScan
Reference Manual
Each programmable family and bar code command label is
listed on the same page with major system commands. The
detailed explanations and special programming flowchart are
printed on facing or following pages. You can read the
explanation and set the FuzzyScan concurrently.
A supplemental bar code command menu incorporates the
bar code command labels of System Command and Option
Code. As you set the FuzzyScan, open the bar code
command menu to find the option code page. You may scan
the desired family code and option code to set FuzzyScan. If
you want to change the programming family for multiple
settings, you need only turn over the programming page to
find next desired programming family.
Family Code
The Family Code is scanned to select the user desired
programming family. FuzzyScan has already provided
more than one hundred programming families to meet any
specific requirements.
Option Code
The Option Codes is a set of bar code commands
represented by “0–9”, “A–F” and finishing selection (FIN).
For most setting, you must select at least one option code
following the family code selection to set the desired
parameter for the selected programming family.
13
Configure Your FuzzyScan
If the programming family must take multiple scans
selection, cycling scan selection, or dual level selection
procedures, the family of the programming menu will be
marked with the matched representing symbol of
Programming Category (P.C.) in bold font listed in the
following table. You can easily find the bold mark in the
programming menu, and refer to their flowcharts for details.
Before setting the FuzzyScan, please also refer to the
“Beeping Indications” listed in Appendix to understand the
details of programming beeping indications. It will be very
helpful for you to know the existing status while you are
programming the FuzzyScan.
Programming Procedures
Wireless FuzzyScan
Reference Manual
As you scan the bar code command to select the desired
parameters, information about the final selected parameters
represented by the bar code commands are stored in the
FuzzyScan’s internal Flash Memory ASIC or non-volatile
memory. If you turn off the unit, the Flash Memory ASIC or
non-volatile memory retains all programming options. You
need not re-program the FuzzyScan if you want to keep the
existing configurations in the next power on.
The programming procedures of FuzzyScan are designed
as simple as possible for ease of setting. Most
programming families take the Single Scan Selection
programming procedure. But several programming families
have more complex and flexible programmable options,
and you must take Multiple Scans Selection, Cycling
Scan Selection or Dual Level Selection to complete their
programming procedures. Each kind of programming
procedure is listed in the following pages for your reference.
Please give careful attention to become familiar with each
programming procedure.
Conventions of Programming Menu
Conventions
Descriptions
Factory Default Value
P.C.
Programming Category
SS : Signle scan selection
MS : Multiple scans selection
CS : Cycling scan selection
DS : Dual level scan selection
14
( )
Necessary Option Code
[ ]
Selectable Option Code
Configure Your FuzzyScan
Program & End
System List, Group & Master Default
Scan
“PROGRAM”
Scan
“SYSLIST”
FuzzyScan will enter programming mode,
and inhibit all non-programming functions.
FuzzyScan will list the product information and
revision number to host via selected host interface,
Wireless FuzzyScan
Reference Manual
then issue the completion beeping.
Scan
“END”
Scan
“M_DEFAULT”
FuzzyScan will exit programming mode, and store all
parameters in Flash Memory ASIC or non-volatile memory,
then issue the completion beeping.
FuzzyScan will recover all programmable
parameters into factory preset configurations,
then issue the completion beeping.
Please note that the FuzzyScan will take 3-4 seconds to
store parameters in internal Flash Memory ASIC or
non-volatile memory after you scan the “END”. Please
don’t turn off the power before the completion beeping. It
may destroy all configured parameters.
15
Configure Your FuzzyScan
Single scan selection
Multiple scans selection
Scan
Scan
“PROGRAM”
Scan
One of Family Codes
“PROGRAM”
Enter programming mode.
Select one of desired
Scan
One of Family Codes
programming families.
Select one of desired
programming families.
1. Select one or several
Select one option code of
Scan
One of Option Codes
Enter programming mode.
Scan One or
Several Option Codes
desired parameter.
option codes to select
desired parameters.
2. If it’s necessary, scan
Yes
Yes
Want to select another
Repeat
Selection
programming family?
“FIN” to terminate
Repeat
Selection
option code selection.
Wireless FuzzyScan
Reference Manual
Want to select another
No
No
Scan
programming family?
Scan
Exit programming mode.
“END”
“END”
16
Exit programming mode.
Configure Your FuzzyScan
Cycling scan selection
Dual level selection
Scan
“PROGRAM”
Scan
One of Family Codes
Scan
“PROGRAM”
Enter programming mode.
Select one of desired
Scan
One of Family Codes
programming families.
Cycling select one or
Scan
One of Option Codes
(1st) Scan
Several Option Codes
several option codes of
desired parameters as
“Single” or “Multiple”
(2nd) Scan One or
Several Option Codes
Wireless FuzzyScan
Reference Manual
Scan “FIN”
Repeat
Selection
programming families.
Select several option codes
of desired parameters.
1. Select one or several
parameters.
2. If it’s necessary, scan
Finish cycling selection.
“FIN” to terminate
(If necessary)
option code selection.
Yes
Want to select another
Repeat
Selection
programming family?
Want to select another
programming family?
No
Scan
“END”
Select one of desired
option codes of desired
scans selection.
Yes
Enter programming mode.
No
Scan
“END”
Exit programming mode.
17
Exit programming mode.
Configure Your FuzzyScan
Host Interface Selection
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Host Interface Selection
MS
MS
MS
MS
MS
MS
MS
MS
MS
MS
Parameter Selection
IBM PS/2, 25-30 series keyboard wedge interface
Standard/TTL RS-232 peer-to-peer serial
Wand emulation
USB Com Port Emulation
PS/2 (DOS/V) direct link (keyboard replacement)
PS/2 (DOS/V) keyboard wedge turbo mode
PS/2 (DOS/V) keyboard wedge standard mode
Laser emulation
USB HID standard mode
USB HID turbo mode
18
Option Code
02
06
08
09
10
13
14
17
18
19
Configure Your FuzzyScan
Symbology Reading Control
♦ User Defined Symbol ID ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Symbol ID : 1 character
DS
Parameter Selection
Code 128 (default=B)
UCC/EAN-128 (default=C)
UPC-A (default=A)
EAN-13 (default=F)
Codabar/NW-7 (default=D)
Code 39/Code 32 (default=G)
Code 93 (default=H)
Standard/Industrial 2 of 5 (default=I)
Interleaved 2 of 5 (default=J)
Matrix 2 of 5 (default=K)
China Postal Code (default=L)
German Postal Code (default=M)
IATA (default=O)
Code 11 (default=P)
MSI/Plessey (default=R)
UK/Plessey (default=S)
Telepen (default=T)
GS1 DataBar (default=X)
UPC-E (default=E)
EAN-8 (default=N)
Trioptic Code 39 (Default=W)
UCC Coupon Extended Code (Default=Z)
PDF417/Micro PDF417 (default=V)
Codablock F (default=Y)
Korea Post Code (default =a)
19
Option Code
2nd Option Code
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
26
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
Configure Your FuzzyScan
Symbology Reading Control
♦ Symbology ID Transmission ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Symbology ID Transmission
SS
SS
SS
SS
SS
SS
SS
Parameter Selection
Disable symbology ID transmission
Enable prefix CINO symbology ID transmission
Enable suffix CINO symbology ID transmission
Enable both prefix and suffix CINO symbology ID transmission
Enable prefix AIM symbology ID transmission
Enable suffix AIM symbology ID transmission
Enable both prefix and suffix AIM symbology ID transmission
20
Option Code
0
1
2
3
4
5
6
Configure Your FuzzyScan
Symbology Reading Control
♦ Readable Bar Code Setting ♦
PROGRAM
Family Code Selection
P.C
Readable Symbology Setting
SS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
Remember to scan “FIN” to terminate
this selection. But if you select the
Reference Manual
“ Auto ”, FuzzyScan will terminate this
Wireless FuzzyScan
F_DEFAULT
selection automatically.
Parameter Selection
Option Code
00
01
02
03
04
05
06
07
47
08
38
48
58
68
09
10
11
12
13
14
15
17
18
21
Auto
Code 128 *
UPC-A *
UPC-E *
EAN-13 *
EAN-8 *
Codabar/NW-7 *
Code 39 *
Trioptic Code 39
Standard/Industrial 2 of 5
Matrix 2 of 5
Interleaved 2 of 5 *
China Postal Code
German Postal Code
Code 93 *
Code 11
MSI/Plessey
UK/Plessey
Telepen
GS1 DataBar (RSS-14) *
IATA
PDF417/Micro PDF417
Codablock F
Korea Post Code
If your application is reading known, limited bar code symbologies, you may increase the reading speed and decrease the reading error possibility by selecting those known
symbologies only. Furthermore, to add the “Symbology ID” into the transmitted data is also helpful for applications to identify the specific symbology ID.
Above symbologies marketed with * are enable as default. When you select “Auto”, the scanner only read those symbologies marked with *
When you set the minimum and maximum length of each symbology, please note the data length of scanned bar code doesn’t include star/stop characters.
21
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 39/Code 32 Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Code 39 Family Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Code 39
Enable Code 39
Select Standard Code 39 as primary format
Select Full ASCII Code 39 as primary format
Select Code 32 (PARAF, Italian Pharmaceutical) as primary format
Disable start/stop symbol transmission
Enable start/stop symbol transmission
Disable Code 32 leading A transmission
Enable Code 32 leading A transmission
Disable MOD 43 check digit verification
Enable MOD 43 check digit verification
Disable check digit transmission
Enable check digit transmission
Disable Code 39 buffering
Enable Code 39 buffering
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
Trioptic Code 39 Setting
SS
SS
Disable Trioptic Code 39
Enable Trioptic Code 39
0
1
Code 39 Min. Length
SS
MS
Default (01)
01-Maximum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 39 Max. Length
SS
MS
Default (98)
98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously.
22
Configure Your FuzzyScan
Symbology Reading Control
♦ Codabar/NW-7 Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Codabar Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Codabar
Enable Codabar
Select Codabar standard format
Select Codabar ABC format
Select Codabar CLSI format
Select Codabar CX format
Disable start/stop symbol transmission
Enable ABCD/ABCD start/stop symbol transmission
Enable abcd/abcd start/stop symbol transmission
Enable ABCD/TN*E start/stop symbol transmission
Enable abcd/tn*e start/stop symbol transmission
Disable check digit verification
Enable check digit verification
Disable check digit transmission
Enable check digit transmission
Codabar Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Codabar Max. Length
SS
MS
Default (98)
98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
23
Configure Your FuzzyScan
Symbology Reading Control
♦ UPC-A & UPC-E Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UPC Family Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Parameter Selection
Disable UPC-A
Enable UPC-A
Disable UPC-E
Enable UPC-E
Disable UPC-E expansion
Enable UPC-E expansion
Disable UPC standardization
Enable UPC standardization
Disable UPC numeric system
Enable UPC numeric system
Disable UPC-A check digit transmission
Enable UPC-A check digit transmission
Disable UPC-E check digit transmission
Enable UPC-E check digit transmission
Disable UPC “leading 1” portion
Enable UPC “leading 1” portion
24
Option Code
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Configure Your FuzzyScan
Symbology Reading Control
♦ UPC-A & UPC-E Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UPC Supplement Setting
SS
SS
SS
SS
SS
SS
SS
SS
UPC-E & EAN-8 Expansion
UPC-A/E Standardization
UPC Lead 1 Numeric System
Wireless FuzzyScan
Reference Manual
WPC Selection
(UPC/EAN/CAN)
UPC-A
UPC-E
EAN-13
EAN-8
Parameter Selection
Option Code
Select UPC without supplement digits
Select UPC with only 2 supplement digits
Select UPC with only 5 supplement digits
Select UPC with 2/5 supplement digits
Disable force supplement digits output
Enable force supplement digits output
UPC Family Addenda Separator Off
UPC Family Addenda Separator On
0
1
2
3
4
5
6
7
: Expand the 7-digit UPC-E and 8-digit ENA-8 to 12-digit UPC-A and 13-digit EAN-13.
: Expand the 7-digit UPC-E and 12-digit UPC-A to 8-digit EAN-8 to 13-digit EAN-13 with 1 zero insertion.
: Enable to read UPC leading with the 1 numeric system, you must enable this option.
Basic Length
Disable
Check Digit
Disable
Numeric System
With 2-digit
Addendum
With 5-digit
Addendum
Enable
Standardization
Enable
Expansion
12
7
13
8
-1
-1
-1
-1
-1
-1
NC
NC
+2
+2
+2
+2
+5
+5
+5
+5
+1
+1
NC
NC
0
+5
0
+5
25
Configure Your FuzzyScan
Symbology Reading Control
♦ EAN Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
EAN Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable EAN-13
Enable EAN-13
Disable EAN-8
Enable EAN-8
Disable EAN-8 expansion
Enable EAN-8 expansion
Disable EAN-13 check digit transmission
Enable EAN-13 check digit transmission
Disable EAN-8 check digit transmission
Enable EAN-8 check digit transmission
Disable ISBN/ISSN Conversion reading check
Enable ISBN/ISSN Conversion reading check
0
1
2
3
4
5
6
7
8
9
A
B
EAN Supplement Setting
SS
SS
SS
SS
SS
SS
SS
SS
Select EAN without supplement digits
Select EAN with only 2 supplement digits
Select EAN with only 5 supplement digits
Select EAN with 2/5 supplement digits
Disable force supplement digits output
Enable force supplement digits output
EAN Addenda Separator Off
EAN Addenda Separator On
0
1
2
3
4
5
6
7
26
Option Code
Configure Your FuzzyScan
Symbology Reading Control
♦ UCC Coupon Extended Code Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UCC Coupon Extended Code
SS
SS
Parameter Selection
Disable UCC Coupon Extended Code
Enable UCC Coupon Extended Code
Option Code
0
1
Wireless FuzzyScan
Reference Manual
UCC Coupon Extended Code
When enabled, this parameter decodes UPC-A barcodes starting with digit “5”, EAN-13 barcodes starting with digit “99”, and UCC/EAN-128 Coupon Codes. UPC-A,
EAN-13 and EAN-128 must be enabled to scan all types of Coupon Codes.
27
Configure Your FuzzyScan
Symbology Reading Control
♦ IATA & Interleaved 2 of 5 Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
IATA Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable IATA
Enable IATA
Select 15-digit fixed length IATA checking
Select variable length IATA
Disable check digit verification
Enable check digit automatic verification
Enable S/N checking digit verification only
Enable CPN checking digit verification only
Enable CPN, Airline and S/N check digit verification
Disable check digit transmission
Enable check digit transmission
Disable start/stop symbol transmission
Enable start/stop symbol transmission
0
1
2
3
4
5
6
7
8
9
A
B
C
Interleaved 2 of 5 Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Interleaved 2 of 5
Enable Interleaved 2 of 5
Select Interleaved 2 of 5 as primary format
Select German Postal Code as primary format
No check character
Validate USS check digit
Validate OPCC check digit
Disable check digit transmission
Enable check digit transmission
0
1
2
3
4
5
6
7
8
28
Option Code
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 25 Family Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 25 Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Standard/Industrial 2 of 5
Enable Standard/Industrial 2 of 5
Disable Matrix 2 of 5
Enable Matrix 2 of 5
Disable China Postal Code
Enable China Postal Code
Disable check digit verification
Enable check digit verification
Disable check digit transmission
Enable check digit transmission
Code 25 Family Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
6
7
8
9
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Wireless FuzzyScan
Reference Manual
Code 25 Family Max. Length
SS
MS
Default (98)
98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
We recommend that you select only one kind of Code 25 for reading, or set limited maximum and minimum reading length for reading, because the encoding algorithm
of Code 25 isn’t very good. To decode all Code 25 automatically or to read variable length Code 25 will increase the error reading rate.
29
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 11 & Code 93 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 11 Setting
SS
SS
SS
SS
SS
SS
SS
Disable Code 11
Enable Code 11
Disable check digit verification
Select 1-check digit verification
Select 2-check digit verification
Disable check digit transmission
Enable check digit transmission
Code 11 Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
6
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 11 Max. Length
SS
MS
Default (98)
98-Minimum
FIN
(2 digits)
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 93 Setting
SS
SS
SS
SS
Disable Code 93
Enable Code 93
Disable check digit transmission
Enable check digit transmission
Code 93 Min. Length
SS
MS
Default (01)
01-Maximum
0
1
2
3
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 93 Max. Length
SS
MS
Default (98)
98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
30
Configure Your FuzzyScan
Symbology Reading Control
♦ MSI/Plessey Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
MSI/Plessey Setting
SS
SS
SS
SS
SS
SS
SS
Disable MSI/Plessy
Enable MSI/Plessy
Select MOD 10 check digit
Select MOD 10-10 check digit
Select MOD 11-10 check digit
Disable check digit transmission
Enable check digit transmission
MSI/Plessey Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
6
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
MSI/Plessey Max. Length
SS
MS
Default (98)
98-Minimum
FIN
(2 digits)
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
31
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 128 & UCC/EAN 128 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 128/EAN-128 Setting
SS
SS
SS
SS
SS
SS
Disable Code 128 and UCC/EAN-128
Enable Code 128 and UCC/EAN-128
Disable function code conversion
Enable function code conversion
ISBT Concatenation Off
ISBT Concatenation On
Code 128/EAN-128 Min. Length
SS
MS
Default (01)
01-Maximum
Option Code
0
1
2
3
4
5
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 128/EAN-128 Max. Length
SS
MS
Default (98)
98-Minimum
FIN
(2 digits)
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
32
Configure Your FuzzyScan
Symbology Reading Control
♦ UK/Plessey Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
UK/Plessey Setting
SS
SS
SS
SS
SS
SS
SS
SS
Disable UK/Plessey
Enable UK/Plessey
Select UK/Plessey Standard Format
Select UK/Plessey CLSI Format
Disable Convert X to A-F
Enable Convert X to A-F
Disable check digit transmission
Enable check digit transmission
UK/Plessey Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
6
7
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Wireless FuzzyScan
Reference Manual
UK/Plessey Max. Length
SS
MS
Default (98)
98-Minimum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
33
Configure Your FuzzyScan
Symbology Reading Control
♦ Telepen Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Telepen Setting
SS
SS
SS
SS
SS
SS
Disable Telepen
Enable Telepen
Select Telepen Numeric mode
Select Telepen Full ASCII mode
Disable check digit transmission
Enable check digit transmission
Telepen Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Telepen Max. Length
SS
MS
Default (98)
98-Minimum
FIN
(2 digits)
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
34
Configure Your FuzzyScan
Symbology Reading Control
♦ GS1 DataBar Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
GS1 DataBar Setting
SS
SS
SS
SS
SS
SS
Disable GS1 DataBar (RSS-14)
Enable GS1 DataBar (RSS-14)
Disable GS1 DataBar Limited
Enable GS1 DataBar Limited
Disable GS1 DataBar Expanded
Enable GS1 DataBar Expanded
GS1 DataBar Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
FIN
(2 digits)
Only available for Expanded GS1 Databar.
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Wireless FuzzyScan
Reference Manual
GS1 DataBar Max. Length
SS
MS
FIN
(2 digits)
Default (74)
74-Minimum
Only available for Expanded GS1 Databar.
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
35
Configure Your FuzzyScan
Symbology Reading Control
♦ Linear-stacked & Korea Post Code Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Composite Codes Setting
SS
SS
SS
SS
Disable composite codes
Enable composite codes
UPC Composite Mode: UPC never linked
UPC Composite Mode: UPC always linked
0
1
2
3
PDF417/MicroPDF417 Setting
SS
SS
SS
SS
Disable PDF417
Enable PDF417
Disable MicroPDF417
Enable MicroPDF417
0
1
2
3
Codablock F Setting
SS
SS
Disable
Enable
0
1
Korea Post Code Setting
SS
SS
Disable
Enable
0
1
Length fixed in 6 characters.
Composite Codes Setting
If UPC Composite Mode: UPC never linked is selected, UPC barcodes are transmitted regardless of whether a MicroPDF417 symbol is detected.
If UPC Composite Mode: UPC always linked is selected, UPC barcodes are only transmitted when the MicroPDF417 is detected.
36
Option Code
Configure Your FuzzyScan
Keyboard Interface Control
♦ Keyboard Layout (Language) Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Keyboard Layout
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Parameter Selection
Option Code
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
99
USA (QWERTY)
France (AZERTY)
Germany (QWERTZ)
United Kingdom - UK (QWERTY)
Canadian French (QWERTY)
Spain (QWERTY)
Sweden/Finland (QWERTY)
Portugal (QWERTY)
Norway (QWERTY)
Latin America (QWERTY)
Italy (QWERTY)
Netherlands (QWERTY)
Denmark (QWERTY)
Belgium (AZERTY)
Switzerland-Germany (QWERTY)
Iceland (QWERTY)
Japan (DOS/V)
Universal * (see note)
The “Universal Selection” is only for PC/AT, PS/VP, PS/2 and compatible ones in DOS or Windows environment which can perform unique output without Caps Lock
on/off (Output Style) concern. All transmitted data will follow the original full ASCII form. You also need not worry about the upper/lower case control.
Please refer to the ASCII/HEX Table listed in the Appendix to determine HEX codes for characters, symbols, and functions to be used as premble or postamble.
To set preamble or postamble as function key output, you must enable the “Function Key Emulation” feature as listed in page 3-25 first.
Keyboard Interface Message String :
Preamble
Data Length
Prefix Symbol ID
Scanned Data
Suffix Symbol ID
Postamble
Record Suffix
1-15 characters
2-3 digits
1 or 2 characters
Variable length
1 or 2 characters
1-15 characters
1 character
37
Configure Your FuzzyScan
Keyboard Interface Control
♦ Record Suffix, Preamble, Postamble & Caps Lock ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Record Suffix
SS
SS
SS
SS
SS
SS
None
RETURN
TAB
SPACE
ENTER (Numeric Key Pad)
User defined character (1 character)
Preamble
SS
MS
None
1-15 characters
Option Code
0
1
2
3
4
5, (00-7F)
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
MS
None
1-15 characters
FIN
[00-7F], [FIN]
Wireless FuzzyScan
Reference Manual
Maximum 15-character input; scan “FIN” to terminate this selection.
Caps Lock Control
SS
SS
SS
“Caps Lock Off” State
“Caps Lock On” State
Auto Detect (PC/AT, PS/2, Keyboard Replacement and DOS/V Machines only)
0
1
2
Caps Lock Release Control
SS
SS
“Caps Lock On, Caps Off”
“Caps Lock On, Shift Off”
0
1
The function of “Caps Lock Control” and “Key Pad Emulation” are only available for IBM PC/AT, PS/VP, PS/2 series personal computers and compatible machines.
While selecting the other host interfaces, these selections don’t perform the above functions for you.
Please check the actual Caps Lock state in use while software application is running. If the Caps Lock state is off, select “Caps Lock Off” state, then FuzzyScan will
perform normal data transmission. If the Caps Lock state is on, select “Caps Lock On” state. Select “Auto Detect”, FuzzyScan will perform special transmission
handshaking without changing the status of Caps Lock switch.
38
Configure Your FuzzyScan
Keyboard Interface Control
♦ Delay Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Intermessage Delay
SS
MS
Parameter Selection
None
1-99 (x10) msec.
Option Code
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intercharacter Delay
SS
MS
None
1-99 (x5) msec.
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Interfunction Delay
SS
MS
None
1-99 (x5) msec.
FIN
(2 digits)
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intermessage Delay is a time delay between messages output by FuzzyScan. Increasing this delay will help host applications process the incoming data on time.
Intercharacter Delay is a time delay between data characters output by FuzzyScan. These two parameters are used to synchronize data communication when : 1) the data
transmission speed is too fast, characters may be skipped; 2) multitasking operation system or host computers in a network may slow down the keyboard handling; 3)
various notebook or desktop PC systems require different timing parameter settings. Please always add one extra unit as safety margin when adjusting these two
parameters.
Interfunction Delay is a time delay between the transmission of each segment of the message string.
Intermessage Delay, Intercharacter Delay and Interfunction Delay cannot be only worked under SPP and HID modes.
39
Configure Your FuzzyScan
Keyboard Interface Control
♦ Emulation Setting & Upper/Lower Case Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Function Key Emulation
SS
SS
Parameter Selection
Enable ASCII 00-31 code as keyboard function code output
Ctrl-Output
Option Code
0
1
Wireless FuzzyScan
Reference Manual
Refer to Appendix – Keyboard Function Code Table for details.
Key Pad Emulation
SS
SS
Disable key pad emulation
Enable numeric output as key pad (Num Lock On) output
0
1
Upper/Lower Case
SS
SS
SS
SS
Normal case (neglect the upper/lower case control)
Inverse case (change all characters output to inverse case)
Upper case (force all characters output as upper case)
Lower case (force all characters output as lower case)
0
1
2
3
40
Configure Your FuzzyScan
Serial Interface Control
♦ Record Suffix, Preamble ,Postamble Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
STX/ETX Control
SS
SS
Parameter Selection
Option Code
Disable STX/ETX transmission
Enable STX/ETX transmission
0
1
STX/ETX are two characters used to indicate the starting and ending of the total
data frame transmitted via serial interface.
Record Suffix
SS
SS
SS
SS
SS
SS
MS
None
CR (0DH)
LF (0AH)
CRLF (0D0AH)
TAB (09H)
SPACE (20H)
User defined character (1 character)
Preamble
SS
MS
None
1-15 characters
0
1
2
3
4
5
6, (00-7F)
FIN
[00-7F], [FIN]
Wireless FuzzyScan
Reference Manual
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
MS
None
1-15 characters
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Serial Interface Message String (RS232, USB COM) :
STX
Preamble
Data Length
Prefix Symbol ID
Scanned Data
Suffix Symbol ID
Postamble
ETX
Record Suffix
1 character
1-15 characters
2-3 digits
1 or 2 characters
Variable length
1 or 2 characters
1-15 characters
1 character
1 character
41
Configure Your FuzzyScan
Serial Interface Control
♦ Delay Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Intermessage Delay
SS
MS
Parameter Selection
None
1-99 (x10) msec.
Option Code
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intercharacter Delay
SS
MS
None
1-99 (x5) msec.
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Interfunction Delay
SS
MS
None
1-99 (x5) msec.
FIN
(2 digits)
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intermessage Delay is a time delay between messages output by FuzzyScan. Increasing this delay will help host applications process the incoming data on time.
Intercharacter Delay is a time delay between data characters output by FuzzyScan. These two parameters are used to synchronize data communication when : 1) the data
transmission speed is too fast, characters may be skipped; 2) multitasking operation system or host computers in a network may slow down the keyboard handling; 3)
various notebook or desktop PC systems require different timing parameter settings. Please always add one extra unit as safety margin when adjusting these two
parameters.
Interfunction Delay is a time delay between the transmission of each segment of the message string.
Intermessage Delay, Intercharacter Delay and Interfunction Delay cannot be only worked under SPP and HID modes.
42
Configure Your FuzzyScan
Serial Interface Control
♦ Protocol, Baud Rate, Data Frame & Time Out Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Handshaking Protocol
SS
SS
SS
SS
None (free running mode)
RTS/CTS (hardware handshaking)
ACK/NAK (software handshaking)
Xon/Xoff (software handshaking)
Baud Rate (BPS)
SS
SS
SS
SS
38.4K BPS
19.2K BPS
9600 BPS
4800 BPS
2400 BPS
1200 BPS
600 BPS
300 BPS
0
1
2
3
4
5
6
7
Data Frame
SS
SS
SS
SS
SS
SS
SS
SS
8, None, 1
8, Odd, 1
8, Even, 1
8, Space, 1
8, Mark, 1
8, None, 2
7, Odd, 1
7, Even, 1
7, Space, 1
7, Mark, 1
7, None, 2
7, Odd, 2
7, Even, 2
7, Space, 2
7, Mark, 2
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
Time Out Control
SS
SS
SS
MS
None
200 mseconds
500 mseconds
1 second
2 seconds
5 seconds
User defined value (seconds)
0
1
2
3
4
5
6, (2 digits)
0
1
2
3
When the RTS/CTS Hardware Handshaking option is selected, the RTS (request to send) and CTS (clear to send) signals will be issued before normal data
communication. This option is very helpful to ensure the reliability of data communication.
When the ACK/NAK Software Handshaking option is selected, the FuzzyScan waits for an ACK (acknowledge) or NAK (not acknowledge) from the host computer after
each data transmission. If the NAK is received, FuzzyScan will re-send the data until receiving ACK.
The Time Out Control is a pre-defined delay time for FuzzyScan to wait for handshaking, acknowledgment or non-acknowledgment from the host computer.
43
Configure Your FuzzyScan
Wand/Laser Emulation Control
♦ Output Polarity, Signal State, Margin/Module Time, etc. ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Output Polarity
SS
SS
Parameter Selection
Option Code
High level (5Vdc) on Bar (low level on Space)
Low level (0Vdc) on Bar (high level on Space)
0
1
Determine the output voltage level for both bar and space.
Initial Signal State
SS
SS
High Level (5Vdc)
Low Level (0Vdc)
0
1
Wireless FuzzyScan
Reference Manual
Determine the initial state of output voltage level.
Margin Time
SS
SS
SS
SS
10 msec.
15 msec.
20 msec.
25 msec.
30 msec.
50 msec.
100 msec.
Delay time before data transmission
0
1
2
3
4
5
6
Module Time
SS
SS
SS
Extremely short
Short
Medium
Long
0
1
2
3
Narrow/Wide Ratio
SS
SS
SS
1:2
1:2.5
1:3
0
1
2
Code 39/Code 128 Emulation
SS
SS
SS
SS
SS
Disable standard Code 39 emulation
Enable standard Code 39 skip emulation
Enable standard Code 39 replace emulation
Enable Full ASCII Code 39 emulation
Enable Code 128 emulation
0
1
2
3
4
Time base of minimum narrow bar
[ Code 39 Skip ] : When this option is selected, all scanned data will be translated as Standard Code 39 wand/laser emulation output. If any lower case characters are read,
they will be translated to upper case characters. Any other characters that are not available in Code 39 symbology set will be skipped.
[ Code 39 Replace] : Any character not normally available in the standard Code 39 symbology set, will be translated as Space.
44
Configure Your FuzzyScan
Operation Control
♦ Operation Mode, Presentation Scanning Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Operation Mode
SS
SS
Trigger mode
Presentation mode
1
2
Presentation Scanning Auto-sense
SS
SS
Disable
Enable
0
1
Wireless FuzzyScan
Reference Manual
Trigger Mode The scanner goes into standby state after scanning the bar code. You must press the trigger to turn on the light source of the scanner before scanning the
bar code.
Presentation Mode Presentation mode uses ambient light to detect bar codes. The LEDs are off for ambient conditions until a change occurs in the scanner’s field of view.
Then the LEDs turn on automatically to read the bar code. If the light level in the room is not high enough, Presentation Mode may not work properly.
The Presentation Scanning Auto-sense can switch between presentation mode and trigger mode automatically while working with SmartStand or cradle.
45
Configure Your FuzzyScan
Operation Control
♦ Buzzer, Indicator, Vibrator, Inverse Reading, Dollar Sign ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Buzzer Tone Adjust
SS
SS
SS
SS
SS
SS
SS
Buzzer tone – mute
Buzzer tone – low
Buzzer tone – medium
Buzzer tone – high
Buzzer tone - extremely high
Power-on beep
No power-on beep
0
1
2
3
4
5
6
Power On Indicator
SS
SS
SS
Disable (LED off)
LED steady on
LED flash
0
1
2
Vibrator Control
SS
SS
Disable
Enable
0
1
Wireless FuzzyScan
Reference Manual
Optional function, only available for vibrator model.
Inverse Reading
SS
SS
Disable
Enable
0
1
Dollar Sign Control
SS
SS
SS
SS
SS
Dollar sign output as “ $ “
Dollar sign output as “￥“
Dollar sign output as “ € “
Dollar sign output as “ £ “
Dollar sign output as “ ¢ “
0
1
2
3
4
46
Configure Your FuzzyScan
Operation Control
♦ Flash Duty Cycle, Redundancy, Delay Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Flash Duty Cycle
SS
SS
SS
SS
1/2 duty cycle
2/3 duty cycle
3/4 duty cycle
4/5 duty cycle
0
1
2
3
Redundancy (Scan Voting)
SS
SS
SS
SS
SS
SS
None
Level 1
Level 2
Level 3
Level 4
Level 5
To prevent potential miss reading.
0
1
2
3
4
5
Reread Delay
SS
SS
SS
SS
SS
SS
Disable
Immediate time out
Short time out
Medium time out
Long time out
Force verification
0
1
2
3
4
5
Good Read Delay
SS
SS
SS
SS
SS
SS
SS
None
200 msec.
500 msec.
1 sec.
1.5 sec.
2 sec.
3 sec.
0
1
2
3
4
5
6
The Flash Duty Cycle is designed to control the flashing frequency of the light source.
The Redundancy is the number of times the same bar code label has to be decoded before it is transmitted.
The Reread Delay is designed to inhibit FuzzyScan from reading the same bar code label twice in pre-defined short duration. Force Verification will not allow reading of the
same bar code twice.
This Good Read Delay is the minimum amount of time before the scanner can read another bar code.
47
Configure Your FuzzyScan
Operation Control
♦ Time-out Setting, Good Read Beep Duration ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Auto Power Off Duration
SS
SS
SS
SS
Short
Medium
Long
Extremely long
0
1
2
3
Hands Free Time-out
SS
SS
SS
SS
Short
Medium
Long
Extremely long
0
1
2
3
Good Read Duration
SS
SS
SS
SS
Short
Medium
Long
Extremely long
0
1
2
3
The Auto Power Off Duration is a pre-defined power off time out counter for Presentation Mode. The scanner keeps the light source on till the pre-defined auto power off
duration is up. You can adjust this parameter to meet your own application requirement.
The Presentation Mode is referred to as “hands free” modes. The hands free mode will be automatically changed to manual trigger mode if you remove the scanner from
stand. The manual trigger mode will be changed to hands free mode if you place the scanner back to stand. You can set the time for scanner to remain in manual trigger
mode by setting the Hands Free Time-Out. Once the time-out value is up (if there have been no further trigger pulls), the scanner reverts to the original hands free mode.
48
Configure Your FuzzyScan
Operation Control
♦ SmartStand Power Off Time-out ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
SmartStand Power Off Timeout
SS
SS
SS
Parameter Selection
3 mins
5 mins
10 mins
Option Code
0
1
2
Only available for FuuzzyScan Laser model
Wireless FuzzyScan
Reference Manual
The SmartStand Power Off Timeout is a pre-defined duration for scanner placed in SmartStand. While the scanner is placed in SmartStand, the scanner’s built-in sensor
will switch the scanner from hand-held scanning to presentation scanning and the light source will be forced on automatically. The light source will be off when the
pre-defined power off duration is up.
49
Configure Your FuzzyScan
Operation Control
♦ Out-of-range Scanning, Sleep Time-out Control ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Out-of-range Scanning
SS
SS
Disable
Enable
0
1
Link Supervision Time-out
SS
SS
SS
SS
SS
1 sec
3 secs
5 secs
7 secs
9 secs
0
1
2
3
4
Wireless FuzzyScan
Reference Manual
Only available in PAIR & PICO modes
Sleep Time-out of Connect State
SS
MS
6 (x5) minutes
0-99 (x5) minutes
FIN
(2 digits)
Sleep Time-out of Disconnect State
SS
MS
1 minute
0-99 minutes
FIN
(2 digits)
Out-of-range Scanning When radio link is built between the scanner and remote host device, the scanner will transmit each scanned data right after scanning the barcode
data. However, the scanner is preset for unable to scan any barcode data when it loses the radio connection. You can enable the Out-of-range Scanning function to
continue scanning barcode data into memory buffer until radio link resumed.
The Link Supervision Time-out is a pre-defined radio link supervision timeout setting. The scanner will supervise the radio link status every preset seconds.
The Sleep Time-out Control can be set under radio connection or disconnection state. If the scanner is not used within the preset time-out duration, it will automatically
enter “Sleep State” for power saving purpose. You are able to disable this function by setting the time-out duration to “0”.
50
Configure Your FuzzyScan
Operation Control
♦ Batch Scanning Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Batch Scanning Link Control
SS
SS
Radio disable
Radio enable
0
1
Stored Data Transmission
SS
SS
SS
All
On cradle
Scan barcode
0
1
2
Delete Stored Data after
Transmission
SS
SS
Disable
Enable
0
1
The Batch Scanning Link Control is a pre-defined radio option to control the radio-on or radio-off status under batch scanning operation. Please note that if the radio
disable is activated, the radio link will be disconnected once you enter batching scanning. The radio link will be resumed when you transmit the stored data or exit batch
scanning.
The Stored Data Transmission is a pre-defined approach when you want to transmit the scanned data under batch scanning operation. You can transmit the scanned data
by placing the scanner onto the cradle or scanning “Transmit Stored Data” command, or by either one of both methods.
In batching scanning, the default setting of Delete Stored Data after Transmission is disable. The scanner will keep all stored data after transmission until you scan the
“Clear All Stored Data” command. You are also able to delete all stored data after transmission automatically by enabling this function.
51
Configure Your FuzzyScan
Operation Control
♦ Batch Scanning Data Transmission Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Field Delimiter
SS
SS
SS
SS
SS
SS
None
，
SPACE
–
．
User define
Batch Data Quantity Output Format
SS
SS
As many times as the quantity indicates
<Quantity><Field Delimiter><Scanned Data>
0
1
Data Transmission Format
SS
SS
SS
Disable (scanned data only)
Leading with MAC address (MAC address and scanned data)
Leading with ID No. (scanner ID and scanned data)
0
1
2
0
1
2
3
4
5, [00-7F]
Only available for RS232, USB HID and USB COM interface in PAIR & PICO modes
The Field Delimiter is used to separate the specific information and scanned data into two fields. You can choose desired delimiter format.
The Batch Data Quantity Output Format If you want to input the quantity information of barcode data, you can enter the quantity from 1 to 9999 by scanning the quantity
barcodes right after you scanned the barcode data. The quantity information will be stored into the memory storage together with the barcode data. There are two ways to
output the stored barcode data and quantity information.
In PICO mode, up to 7 scanners can be connected with one smart cradle. The Data Transmission Format can help user to identify the source of the transmitted data.
You can choose to transmit the scanned data leading with MAC address or pre-assigned ID.
Example format: <MAC address><Field Delimiter><Data> or <ID><Field Delimiter><Data>.
52
Configure Your FuzzyScan
Operation Control
♦ Bluetooth Device Name & Security Setting♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Bluetooth Device Name
SS
MS
Default device name
User define, 1-14 characters
FIN
[00-7F], FIN
Bluetooth PIN Code
SS
MS
Default Bluetooth PIN Code
User define, 1-8 numbers
FIN
[30-39], FIN
Bluetooth Authentication
SS
SS
Disable
Enable
0
1
The default Bluetooth Device Name is “CINO FxxxBT-xxxx”, you will be able to change the device name by scanning HEX values (1-14 characters).
The default Bluetooth PIN Code is “00000000”, you will be able to change the PIN Code by scanning HEX values (1-8 numbers).
The Bluetooth Authentication You can enable or disable the Bluetooth Authentication between the scanner and remote host device. If this function is enabled, when the
scanner wants to connect itself and sends the data to the host device, the host device has to return a link key shared between the scanner and the host device.
53
Configure Your FuzzyScan
Operation Control
♦ Bluetooth Other Settings ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
HID Link Quality Setting
SS
SS
Disable
Enable
0
1
Bluetooth Power Saving Mode
SS
SS
Disable
Enable
0
1
Wireless FuzzyScan
Reference Manual
The HID Link Quality Setting While using the HID radio link mode, some errors may occur during the data transmission when the radio link is disconnected. You can
enable this function to prevent such error from occurring.
The Bluetooth Power Saving Mode Bluetooth module will enter low consumption mode when you enable this function.
54
Configure Your FuzzyScan
Condensed DataWizard
♦ Preamble, Postamble, Data Length & Symbol ID Trans. ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Preamble
SS
MS
Parameter Selection
None
1-15 characters
Option Code
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
MS
None
1-15 characters
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Data Length Transmission
SS
SS
Disable
Enable 2 digits data length transmission
0
1
If data length exceeds 99, 3-digit data length will be transmitted.
Wireless FuzzyScan
Reference Manual
Symbology ID Transmission
SS
SS
SS
SS
SS
SS
SS
Disable symbology ID transmission
Enable prefix symbology ID transmission
Enable suffix symbology ID transmission
Enable both prefix and suffix symbology ID transmission
Enable prefix AIM symbology ID transmission
Enable suffix AIM symbology ID transmission
Enable both prefix and suffix AIM symbology ID transmission
0
1
2
3
4
5
6
DataWizard is the most powerful, Artificial-Intelligence based data editing expert system provided specially for the FuzzyScan family bar code readers. Through DataWizard,
you can process the scanned data prior the transmissions in many ways as: Insert, Delete, Match, Verify, Replace, Reorganize, and Repeat Transmission. It will help
you to arrange the transmission of scanned data to any specific format without software modification.
Due to the resources used by this system, Full-feature DataWizard is only supported by PowerTool. Through the PowerTool, all settings and configurations can be done
on-screen, under Windows 95/98/NT/2000/XP environment.
A Condensed Version DataWizard is provided by each FuzzyScan series. Through this menu, the condensed DataWizard can be utilized via bar code menu readings with
ease.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
If you have any problem to use DataWizard, please refer to following pages for details and consult your local FuzzyScan vendor or our web site for any assistance.
55
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Formatter Setting ♦
PROGRAM
Family Code Selection
P.C
Formatter Control
SS
MS
MS
1st Insertion
SS
DS
2nd Insertion
Reference Manual
3rd Insertion
Wireless FuzzyScan
F_DEFAULT
4th Insertion
SS
DS
SS
DS
SS
DS
Parameter Selection
Option Code
2nd Option Code
Disable
Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable
Enable
FIN
(2 digits)
[1-3 characters], [FIN]
2-digits identified position; max. 3 insertion characters
position
Disable
Enable
FIN
(2 digits)
2-digits identified position; max. 3 insertion characters
position
Disable
Enable
FIN
(2 digits)
2-digits identified position; max. 3 insertion characters
position
Disable
Enable
FIN
(2 digits)
2-digits identified position; max. 3 insertion characters
position
[1-3 characters], [FIN]
[1-3 characters], [FIN]
[1-3 characters], [FIN]
The Data Formatter is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code
symbologies for formatter control, and provides Multiple Position Insertion and Multiple Character Insertion (max three characters) in the identified position.
While the Data Formatter is enabled, it arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbolology ID or Record
Suffix. All of the above programmable parameters perform the same function depending on your setting.
Regarding the “Bar Code Selection” and “Position Calculation” of data formatter, please refer to page 37 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
56
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Verifier Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Verifier Control
SS
MS
MS
Identified Data Length
SS
MS
Parameter Selection
Option Code
2nd Option Code
Disable
Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable
Enable
FIN
(2 digits)
Determine the identified data length for verification.
1st Identified Character
Wireless FuzzyScan
Reference Manual
2nd Identified Character
3rd Identified Character
SS
DS
SS
DS
SS
DS
Disable
Enable
FIN
(2 digits)
2-digits checking position; 1 identified character
position
Disable
Enable
FIN
(2 digits)
2-digits checking position; 1 identified character
position
Disable
Enable
FIN
(2 digits)
2-digits checking position; 1 identified character
position
[00-7F]
[00-7F]
[00-7F]
The Data Verifier is used to provide advanced verification for error-free scanning and to work as an Embedded Data Transmitting Filter.
All data must conform to the Identified Bar Code Symbologies, Identified Data Length, and one to three Identified Characters in the checking position. Otherwise, the
FuzzyScan will not transmit the data to the host computers or terminals, but will instead issue 3 long beeps for verification error and skip the scanned data.
The Data Verifier checks only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix.
Regarding the “Bar Code Selection” and “Position Calculation” of Data Verifier, please refer to page 37 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
57
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Replacer Setting ♦
PROGRAM
Family Code Selection
P.C
Replacer Control
SS
MS
MS
1st Replacement
SS
DS
2nd Replacement
Reference Manual
3rd Replacement
Wireless FuzzyScan
F_DEFAULT
SS
DS
SS
DS
Parameter Selection
Option Code
2nd Option Code
Disable
Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable
Enable
FIN
(2 digits)
[00-7F]
2-digits identified position; 1 replacement character
position
Disable
Enable
FIN
(2 digits)
2-digits identified position; 1 replacement character
position
Disable
Enable
FIN
(2 digits)
2-digits identified position; 1 replacement character
position
[00-7F]
[00-7F]
The Data Replacer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code
symbologies for replacer control, and provides Multiple Position Replcement in the identified position.
All data must conform to the Identified Bar Code Symbologies, and one to three Identified Characters in the identified position While the Data Replacer is enabled, it
arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix.
Regarding the “Bar Code Selection” and “Position Calculation” of Data Replacer, please refer to page 37 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find mathced HEX value.
58
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Organizer Setting ♦
PROGRAM
Family Code Selection
P.C
Organizer Control
SS
MS
MS
1st Organization
SS
DS
2nd Organization
Reference Manual
Include/Exclude Control
Wireless FuzzyScan
F_DEFAULT
SS
DS
SS
DS
Parameter Selection
Option Code
2nd Option Code
Disable
Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable
Enable
FIN
(2 digits)
2-digits identified position;
Forward/backward data transmission setting
position
direction
Disable
Enable
FIN
(2 digits)
2-digits identified position;
Forward/backward data transmission setting
position
direction
Transmitted data excluded the data of identified position
Transmitted data included the data of identified position
0 (Forward)
1 (Backward)
0 (Forward)
1 (Backward)
0
1
The Data Organizer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code
symbologies for organizer control, and provides maximum two identified positions to send the data forward or backward. It also allows you to control the transmitted data
including or excluding the data of identification position. Please refer to the application example listed in page 37 for details.
While the Data Organizer is enabled, it arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record
Suffix.
Regarding the “Bar Code Selection” and “Position Calculation” of Data Organizer, please refer to page 37 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table.
59
Configure Your FuzzyScan
[Data Verifier, Data Replacer, Data Organizer]
Select a Bar Code Symbology
If there is a 11-character data string, please refer to the
following to calculate the actual position for identification.
Wireless FuzzyScan
Reference Manual
You can select one or all types of bar code symbologies to
use Condensed DataWizard for advanced transmission
arrangement. If you scan “00” to select all types, the
FuzzyScan will arrange all incoming data to meet your
pre-defined format. If you want to select only one type bar
code, please select one of the option code listed below.
Code 128 : 01
EAN-8 : 05
Code 93 : 09
UCC/EAN 128 : 31
EAN-8 with 2 supple : 35
Code 11 : 10
UPC-A : 02
EAN-8 with 5 supple.: 45
MSI/Plessey : 11
UPC-A with 2 supple.: 32
Codabar/NW-7 : 06
UK/Plessey : 12
UPC-A with 5 supple.: 42
Code 39 : 07
Telepen : 13
UPC-E : 03
Code 32 : 37
GS1 Data Bar : 14
UPC-E with 2 supple.: 33
Trioptic Code 39: 47
IATA : 15
UPC-E with 5 supple.: 43
Matrix 2 of 5 : 38
Coupon Code : 16
EAN-13 : 04
Interleaved 2 of 5 : 48
PDF417/MicroPDF417: 22
EAN-13 with 2 supple. : 34
China Postal Code : 58
Codablock: 23
EAN-13 with 5 supple. : 44
German Postal Code : 68
Korea Post Code: 26
X
X
X
X
X
X
X
X
X
X
X
00
01
02
03
04
05
06
07
08
09
10
Application Example
If your bar code label is a 16-digit Interleaved 2 of 5 which
includes the information of 6-digit date code, 6-digit serial
number and 4-digit unit price, you want the FuzzyScan do
the following for you without software modification:
Apply only Interleaved 2 of 5 to the condensed
DataWizard.
Check bar code is actually with 16-digit length.
Allow bar code output whose date code is leading with
“9”.
Position Calculation
Three outputs with “TAB” suffix.
[Data Formatter]
The date code output should skip “9” and replaced it by
“A”.
If there is a 5-character input data string, refer to the following
to calculate the actual position for insertion:
X
00
X
01
X
02
X
03
The serial number output should be led with “SN”.
X
04
The unit price output should be skipped the first 2
digits.
05
Test Bar Code : 9 8 1 0 2 5 1 2 3 4 5 6 9 8 7 6
Actual Output : A81025[TAB]SN123456[TAB]76[TAB]
60
Configure Your FuzzyScan
Programming Procedure
[Data Verifier]
[Data Replacer]
Scan “Program” to enter the programming mode.
Scan “Replacer Control” and set bar code symbology
to “48”.
Scan “Verifier Control” and set bar code symbology to “48”
(Interleaved 2 of 5).
Scan “1st Replacement” and set the identified position
to “00”, then replaced character to “41” (Hex Code of
A).
Scan “Identified Data Length” and set the length to “16”.
Scan “1st Identified Character” and set the identified
position to “00”, then set the identified character to “39”
(Hex Code of 9).
[Data Organizer]
Scan “Organizer Control” and set bar code symbology
to “48”.
Wireless FuzzyScan
Reference Manual
[Data Formatter]
Scan “Formatter Control” and set bar code symbology to
“48”.
Scan “1st Organization” and set the identified position
to “16”, then set the data transmission to “0” (forward).
Scan 1st Insertion” and set the identified position to “06”,
then inserted characters to “09” (Hex Code of TAB), “53”
(Hex Code of S), “4E” (Hex Code of N).
Scan “2nd Organization” and set the identified position
to “17”, then set the data transmission to “1”
(backward).
Scan “2nd Insertion” and set the identified position to “12”,
then inserted character to “09”. In the final, you must scan
“FIN” (Finish) code to terminate this selection.
Scan “END” (Exit) to terminate the programming.
[Important Notice]
Scan “3rd Insertion” and set the identified position to “16”,
then inserted character to “09”. In the final, you must scan
“FIN” (Finish) code to terminate this selection.
Please note that Condensed DataWizard will follow the
preset working flow as below:
Verifier Formatter Replacer Organizer
So when you set the identified position in Data Organizer,
you must consider the inserted data which you already set
via Data Formatter.
61
Appendix
Symbology ID Table
Each AIM Code Identifier contains the three-character string ]cm where:
] = Flag Character
c = Code Character
m = Modifier Character
Cino ID
Code Family
Primary Format
AIM ID
Code
Code
Modified
Character
Character
Character
UPC-A
UPC-A with 2 supple.
A
UPC-A with 5 supple.
UPC
E
UPC-E
UPC-E with 2 supple.
Cino ID
E
EAN/JAN-8
1
EAN/JAN-8 with 2 supple.
2
EAN/JAN-8 with 5 supple.
m
EAN/JAN
2
Reference Manual
Wireless FuzzyScan
Codabar
Code 25
IATA
Code 128
B
UCC/EAN-128
C
C
Code
Code
Modified
Character
Character
Character
N
E
1
4
2
EAN/JAN-13
EAN/JAN-13 with 2 supple.
m
F
E
EAN/JAN-13 with 5 supple.
Example: A UPC-A bar code 012345678950 with 2 supplement 12 is
transmitted as ]E0012345678950]E112
Code 128
Primary Format
m
1
UPC-E with 5 supple.
Code Family
AIM ID
1
2
Example: A EAN/JAN-8 bar code 49123562 with 5 supplement 12345 is
transmitted as ]E449123562]E212345
m
Code 93
Code 93
H
G
m
1
Code 11
Code 11
P
H
m
Codabar/NW-7
D
F
m
MSI/Plessey
MSI/Plessey
R
M
m
Standard/Industrial 2 of 5
I
S
0
UK/Plessey
UK/Plessey
S
P
0
Matrix 2 of 5
K
X
0
Telepen
Telepen
T
B
m
Interleaved 2 of 5
J
I
m
X
e
0
Code 39
G
A
m
Code 39 Trioptic
W
X
0
Code 32
G
A
0
PDF417
PDF417/Micro PDF417
V
L
0
Codablock
Codablock F
Y
O
0
Korea Post
Korea Post Code
a
X
0
China Postal Code
L
X
0
German Postal Code
M
I
3
IATA
O
R
m
UCC Coupon Code
Z
Example : A UPC-A 512345678900 + UCC/EAN-128 81010123451297
UCC Coupon bar code is transmitted as]E0512345678900]C181010123451297
Example: A EAN-13 9923456789019 + UCC/EAN-128 81010123451297
bar code is transmitted as ]E09923456789019]C181010123451297
GS1 DataBar
GS1 Databar
Compsoite
Composite Code
Code 39
Remark: Above examples are given for the transmission of AIM ID.
62
Appendix
Wireless FuzzyScan
Reference Manual
Keyboard Function Code Table
No.
ANSI
ASCII
00
NUL
00H
01
SOH
02
Key Function
No.
ANSI
ASCII
Key Function
RESERVED
16
DLE
10H
F7
01H
CTRL (Left)
17
DC1
11H
F8
STX
02H
ALT (Left)
18
DC2
12H
F9
03
ETX
03H
SHIFT
19
DC3
13H
F10
04
EOT
04H
CAPS LOCK
20
DC4
14H
F11
05
ENQ
05H
NUM LOCK
21
NAK
15H
F12
06
ACK
06H
ESC
22
SYN
16H
INS (Insert) (Edit)
07
BEL
07H
F1
23
ETB
17H
DEL (Delete) (Edit)
08
BS
08H
BACK SPACE
24
CAN
18H
HOME (Edit)
09
HT
09H
TAB
25
EM
19H
END (Edit)
10
LF
0AH
F2
26
SUB
1AH
PAGE UP (Edit)
11
VT
0BH
F3
27
ESC
1BH
PAGE DOWN (Edit)
12
FF
0CH
F4
28
FS
1CH
UP (Edit)
13
CR
0DH
ENTER (CR)
29
GS
1DH
DOWN (Edit)
14
SO
0EH
F5
30
RS
1EH
LEFT (Edit)
15
SI
0FH
F6
31
US
1FH
RIGHT (Edit)
To emulate the keyboard function key input for user definable parameters, user must configure actual content using the
Reserved ASCII 0 – 31 characters, and also Enable the “Function Key Emulation”. Otherwise, the Ctrl output will be done
by the scanner. Please refer to the above Keyboard Function Code Table which is for IBM PC/XT/AT, PS/2, PS/VP,
COMPAQ PC, HP Vectra PC, Notebook PC, APPLE and PowerMac, and WYSE PC Enhanced or fully compatible machines.
63
Appendix
ASCII Input Shortcut
To configure the user definable parameters of FuzzyScan via
programming menu, FuzzyScan will ask you to scan your
desired ASCII value in HEX form. You have to refer to the
“HEX/ASCII Table” for details.
HEX/ASCII Reference Table
H
0
1
2
3
4
5
6
7
0
NUL
DLE
SPACE
0
@
P
`
p
Example:
1
SOH
DC1
!
1
A
Q
a
q
If you want the scanned data output leading with a Dollar
Sign, you have to set the “Preamble” to “$”. The configuration
procedure is listed below for reference.
2
STX
DC2
"
2
B
R
b
r
3
ETX
DC3
#
3
C
S
c
s
4
EOT
DC4
$
4
D
T
d
t
5
ENQ
NAK
%
5
E
U
e
u
6
ACK
SYN
&
6
F
V
f
v
7
BEL
ETB
'
7
G
W
g
w
8
BS
CAN
(
8
H
X
h
x
9
HT
EM
)
9
I
Y
i
y
A
LF
SUB
*
:
J
Z
j
z
B
VT
ESC
+
;
K
[
k
{
C
FF
FS
,
<
L
\
l
|
D
CR
GS
-
=
M
]
m
}
Scan the system command – FIN (Finish) to terminate
Preamble setting.
E
SO
RS
.
>
N
^
n
~
F
SI
US
/
?
O
_
o
DEL
Scan the system command – End to exit the programming
mode for normal operation.
Example : ASCII “A” → HEX “41”; ASCII “a” → “61”
L
Scan the system command – PROGRAM listed on page
3-24 to enter programming mode.
Scan family code – PREAMBLE to select this family.
Refer to the Hex/ASCII Table, you will find the HEX value
of “$” is 24.
Scan the option code – 2 listed on the fold out back cover.
Wireless FuzzyScan
Reference Manual
Scan the option code – 4 listed on the fold out back cover.
: High Byte of HEX Value
: Low Byte of HEX Value
64
Appendix
Link Mode Quick Set
Uninstall
SPP Slave Mode
PAIR Mode
HID Mode
SPP Master Mode
PICO Mode
Wireless FuzzyScan
Reference Manual
Operation Mode Quick Set
Trigger Mode
Presentation Mode
65
Appendix
Host Interface Quick Set
(Work with Smart Cradle only)
RS232 Serial
PS/2 (DOS/V) KBW Standard Mode
USB HID Standard Mode
Keyboard Replacement
PS/2 (DOS/V) KBW Turbo Mode
USB HID Turbo Mode
Wireless FuzzyScan
Reference Manual
USB Com Port Emulation
66
Appendix
Option Codes
0
8
4
C
1
9
5
D
2
A
6
E
Wireless FuzzyScan
Reference Manual
3
B
7
F
FIN (Finish)
END (Exit)
67
Appendix
System Commands
PROGRAM
(Enter Programming Mode)
Save Configuration
Sleep
FIN (Finish)
Clone
Paging
END
(Exit Programming Mode)
Factory Default
Wireless FuzzyScan
Reference Manual
PowerTool Host Link
System Information List
(SYSLIST)
Master Default
Factory Default: After scanning” Factory Default” command, all parameters will be returned to factory default value (The radio link will be disconnected and the
scanner will revert to uninstall state).
Master Default: After scanning “Master Default” command, the scanner will remain the pre-set parameters of Host Interface Selection, Keyboard Interface
Control (except Record Suffix; Preamble; Postamble), Serial Interface Control (except Record Suffix; Preamble; Postamble), Wand/Laser Emulation Control,
Bluetooth Device Name, Bluetooth PIN Code, and Out-of-range Scanning, the rest of parameters will be returned to default value (The radio link is still keep
on).
Save User Default
User Default
68
FuzzyScan Wireless Reference Manual
CINO GROUP
PC WORTH INT’L CO., LTD.
www.cino.com.tw
">