http://www.3jtech.com.tw
Technical Document
for
IPC2(V)-5600, IPC2(V)-3360
a V.90, V.34+ Modems for PC104
Interface Industrial PC
Revision Issue Date Engineers/Comments
V1.0
Dec.15, ‘01
Peter
V1.1
Oct. 15, ‘02
Add Speaker Jack Output Power/Kiwi
V.1.2
Feb. 25, ‘03
+12V/-12V DC are needed only for IPC2V-5600 with voice function only
Copyright by 3JTech Co., Ltd. All rights reserved.
Related Documents:
1) AT Command Sets (1199_AT-RC56D from Conexant): Available upon request.
2) Design Guide (1154r#-RC56D, from Conexant): for internal use only
3) PCB: for internal use only
4) Regulation Approval Reports: Available upon request
CTR21+TBR21
FCC Part 68
FCC Part 2 and Part 15
EN60950
UL 1950
Austel (Available thru 3JTech’s distributor in Australia)
3J Tech. Co., Ltd
Tel: 886-(0)2 25006916
342 Fushing N. Rd., 2F, Taipei, Taiwan 104
Fax: 886-(0)2 25069793
http://www.3jtech.com.tw
Table of Content
Introduction .....................................................................................................2
Block Diagram ................................................................................................3
Function Specification .....................................................................................4
Power Consumption.......................................................................................................... 4
Operating Temperature Range ......................................................................................... 4
Storage Temperature Range............................................................................................. 4
Speaker Output Power for IPC2V-5600............................................................................ 4
DIP Switch Settings ........................................................................................5
Mechanical Drawing of the PCB .....................................................................6
Schematic .......................................................................................................9
Components on Top Side of the PCB ........................................................... 11
Components on Bottom Side of the PCB ......................................................12
2
http://www.3jtech.com.tw
Introduction
IPC2-5600 is a PC104 add-on card V.90 modem using Conexant modem chip sets,
RC56D. PC104 is a 16 bit data bus interface for industrial PC. Since RC336D is pin
compatible to RC56D. 3JTech could also provide IPC2-3360. With additional
components mounted on the IPC2 PCB, the modem could have additional voice
function. The model is called IPC2V-5600 or IPC2V-3360. The product has the
following regulation approvals:
(CTR21+TBR21)
FCC Part 68
Part 15
EN 60950
UL 1950
YES
YES
YES
YES
Regist. #: BT2010196
File #: 655-CX-2000
Report #: J1015119
Report #: T60LVL20 File #: E172664
Report #: D2064018 E01 Regis. #: 5CQ TAI-40146-M%-E
YES
Project #: 00NK90945
LVD Report is for EN60950
TUV Report is for CTR21 & TBR21
EMC Test is for Part 2 and Part 15
*** The product also has Austel approval through our distributor in Australia.
*** The reports are available upon request.
*** 3JTech will conduct other regulation approvals upon customer’s request for the
product.
3
CE
YES
http://www.3jtech.com.tw
Block Diagram
Plug and Play
(Option)
Tip
DAA
Interface
PC/104 16 bit
Bus Interface
Ring
MCU
L2800-38
Modem Data Pump
RP56D/SP
R6764-61
Serial
E EPROM
256Kx8
Microphone
&
Headphone
28.224Mhz
SRAM
1M(128Kx8)
Flash ROM
2M(256Kx8)
IPC 2(V)-5600 M odem System Block Dia gr a m
4
http://www.3jtech.com.tw
IPC2(V)-5600 Modem Specification
Function Specification:
• Data modem
− ITU-T V.90 (56 kbps)
− V.34 (33.6 kbps)
− V.32 bis, V.32, V.22 bis, V.22, V.23, and V.21
− Bell 212A and 103
− V.42 LAPM, MNP 2-4, and MNP 10 error correction
− V.42 bis and MNP 5 data compression
− MNP 10EC™ enhanced cellular performance
• Fax modem send and receive rates up to 14.4 kbps
− V.17, V.29, V.27 ter, and V.21 channel 2
• V.80 synchronous access mode supports host-based communication protocols
• Voice/TAM/telephony extensions mode(voice Version)
− Handset support
− Full-duplex speakerphone mode
− ITU-T V.61 modulation (4.8 kbps data with audio)
• Communication software compatible AT command sets
• Built-in host/DTE interface with speeds up to 230.4 kbps
• PC/104 16bit Bus Interface
• Plug and Play supported (PnP Version)
• Work with Windows 95, 98, ME, NT 4.0 and Windows 2000 system
• Work with Linux system, WinCE, WinCE.net, etc.
Power Consumption
− DC5V 240mA
− DC 12V 20mA (for IPC2V-5600 with voice function)
− DC -12V 20mA (for IPC2V-5600 with voice function)
* Note: only 5V DC is needed for IPC2-5600.
Operating Temperature Range: 0 ~ 70oC
Storage Temperature Range: -15 ~ 85oC
Speaker Output Power
The IPC2V-5600 speaker Jack output voltage range from 20mV to 2V and
driver current 40mA Max.
The Max power output is 80mW so you need a booster.
5
http://www.3jtech.com.tw
IPC2(V)-5600 DIP Switch Setting
There are two dip-switches on the PCB. The locations are show on the Figure 1.
Switch number one is for setting which COM port the add-on card will be assigned to.
The second switch is for setting the IRQ number according to which COM port
assigned.
Table 1: SW1 – Switch settings for COM port selection or Plug and Play
Function\No.
1
2
3
4
5
PnP
OFF
ON
OFF
ON
OFF
switch
ON
OFF
ON
OFF
ON
Table 2: SW2 – I/O port & IRQ setting
No.
1
2
3
4
5
6
7
8
9
(IRQ3) (IRQ4) (IRQ5) (IRQ7) (IRQ9)
COM1
3F8h/IRQ4
ON
OFF
ON
OFF
OFF
ON
COM2
2F8h/IRQ3 OFF
ON
ON
OFF
ON
OFF
COM3
3E8h/IRQ4
ON
OFF
OFF
ON
OFF
ON
COM4
2E8h/IRQ3 OFF
ON
OFF
ON
ON
OFF
6
OFF
(Nonstandard IRQ
support for COM port)
http://www.3jtech.com.tw
Dip Switch 1
Dip Switch 2
Figure 1: Location of the Dip Switch
7
http://www.3jtech.com.tw
Mechanical Drawing of the PCB
90.8
12.7
6.4
8.9
5.1
64
26.7
5.1
1
ψ6.4 PADx4
7.6
82.5
85.1
90.2
40 1
Primary Side
Pitch:2.54mm
ψ3.2 Hole x4
21
20
32
14
1.6±0.1
33
95.9
IPC2(V)-5600 Dimensions
Unit: mm
Tolerance:
8
±0.1mm