Alcatel | OmniAccess 2.0 | ALCATEL-LUCENT OMNIACCESS RAP3 - Alcatel

ALCATEL-LUCENT
OMNIACCESS RAP3
SINGLE RADIO 802.11N
REMOTE ACCESS POINTS
The multifunctional OmniAccess RAP3 delivers secure 802.11n wireless and wired network
access to corporate resources from branch and home offices. Centrally managed by OmniAccess
WLAN Switch/Controllers, the RAP3 extends corporate resources to remote locations by establishing site-to-site VPN tunnels to the data center.
The RAP3 offers a variety of enterpriseclass features, including role-based
network access, policy-based forwarding,
and Adaptive Radio Management (ARM),
which gives remote workers the same
high-quality Wi-Fi experience they get at
corporate headquarters.
Delivering a wireless data rate of
up to 300 Mbps, the RAP3 has three
10/100BASE-T Ethernet ports and one
USB port for connecting to 3G and 4G
networks. It is also available with an
802.3af power-over- Ethernet (PoE) port
for IP phones or other devices.
At locations that require greater coverage,
the RAP3 can join an OmniAccess Instant
WLAN cluster. Simply install additional
RAP3s or any Instant AP and the entire
cluster is managed as one. If one Instant
AP fails, another AP automatically takes
over with no disruption.
Advanced Features
• Automatic device provisioning, firmware
upgrades and inventory management
• ARM delivers best-in-class RF
management, including automatic transmit
power and channel control with auto
coverage-hole correction
• Security:
¬With an OpenDNS service subscription,
OmniAccess Instant RAPs delivers
integrated web filtering, malware and
botnet protection to every device
connected to the WLAN
¬Integrated Trusted Platform Module
(TPM) for secure storage of credentials
and keys
¬SecureJack-capable for secure tunneling
of wired Ethernet traffic
OPERATING MODE
• Wireless
¬802.11b/g/n Mobility Controllermanaged RAP
¬802.11b/g/n OmniAccess Instant AP
¬802.11b/g/n air monitor
¬Hybrid WLAN and air monitor
¬Configurable to support 802.11n
HT 20/40 channels or mixed-mode
deployment IEEE 802.11b/g/n
• Wired
¬10/100BASE-T Ethernet, PoE capable
¬User authentication: 802.1X, captive
portal, MAC authentication or open
access
¬Policy-based forwarding for local
resource access
Wireless Radio Specifications
• AP type: 2.4 GHz 802.11n indoor
• Software-configurable 2.4-GHz radio
• 2×2 MIMO 802.11n with two spatial
streams and up to300 Mbps wireless
data rate
• Supported frequency band (countryspecific restrictions apply): 2.4000 GHz
to 2.4835 GHz
• Available channels: Managed by Virtual
Controller or Mobility Controller,
dependent upon configured
regulatory domain
• Supported radio technologies:
¬802.11b: Direct-sequence spreadspectrum (DSSS)
¬802.11n: Orthogonal frequency division
multiplexing (OFDM)
¬802.11n: 2x2 MIMO with 2 spatial
streams
• Supported modulation types:
¬802.11b: BPSK, QPSK, CCK
¬802.11n: BPSK, QPSK, 16-QAM, 64-QAM
• Transmit power: Configurable in
increments of 0.5 dBm
• Maximum (aggregate) transmit power:
+19 dBm (limited by local regulatory
requirements)
Power In
• AC-to-DC power adapter (included)
– RAP3WN:
Mechanical
• Dimensions/weight (unit with desk stand):
¬AC input: 100-240 volts AC/0.5 A
¬129 mm x 109 mm x 64 mm
(5.1” x 4.3” x 2.5”)
¬DC output: 12 volts DC/1.5 A
¬180 g (6.6 oz)
• AC-to-DC power adapter (included)
– RAP3WNP:
¬AC input: 100-240 volts AC/0.75 A
•
Dimensions/weight (shipping):
¬218 mm x 150 mm x 64 mm
(8.6” x 5.9” x 2.5”)
¬DC output: 48 volts DC/0.75 A
¬RAP3WN: 510 g (1.1 lb)
• Maximum power consumption – RAP3WN:
¬Maximum (excluding USB): 4.0 watts
¬Maximum (using USB): 6.5 watts
• Maximum power consumption
– RAP3WNP:
¬Maximum (excluding USB and PoE):
5.5 watts
¬Maximum (using USB, no PoE): 8.0 watts
¬Maximum (using USB, full PoE): 26 watts
Antenna
• Two integrated, omni-directional antenna
elements for 2×2 MIMO
• Antenna gain: 2.0 dBi
Interfaces
• Network:
¬RAP3WNP: 620 g (1.4 lb)
Environmental
• Operating:
¬Temperature: 0° C to 40° C
(+32° F to +104° F)
¬Humidity: 5 to 95% non-condensing
• Storage and transportation temperature
range:
¬Temperature: -40°C to +70° C
(-40° F to +15 8°F)
Regulatory
• FCC/Industry of Canada
• CE Marked
• R&TTE Directive 1995/5/EC
• Low Voltage Directive 72/23/EEC
• EN 300 328
• Maximum ratio combining (MRC) for
improved receiver performance
¬E0 (WAN): One 10/100BASE-T Ethernet
(RJ-45), auto-sensing link speed and
MDI/MDX
• Cyclic Delay Diversity for improved
downlink RF performance
¬E1-E2 (LAN): Two 10/100BASE-T
Ethernet (RJ-45), auto-sensing
• Short guard interval for 20-MHz and
40-MHz channels
link speed and MDI/MDX
• CB Scheme Safety, cTUVus
¬Optional 802.3af PoE (15.4 watts) on
the E2 port for IP phones and other
equipment
• Wi-Fi certified 802.11a/b/g/n
• Space time blocking code (STBC) for
increased range and improved reception
• Association rates (Mbps):
¬802.11b: 1, 2, 5.5, 11
¬802.11: 6, 9, 12, 18, 24, 36, 48, 54
¬802.11n: MCS0 - MCS15 (6.5 Mbps 300 Mbps)
• 802.11n high-throughput (HT) Support:
HT 20/40
• 802.11n packet aggregation: A-MPDU,
A-MSDU
• Power:
Alcatel-Lucent Enterprise Data sheet
2
• UL/IEC/EN 60950
Certifications
Warranty
• Limited lifetime warranty
¬1 x DC power connector
• Other:
Minimum AOS version
¬One USB 2.0 port (Type A connector)
• 6.1.4.0
¬One four-pin console interface (custom)
• Instant 3.0
Mounting
Table 1. RF performance table
• Desktop (using stand supplied with
product)
• Wall (using optional wall-mount accessory)
Alcatel-Lucent OmniAccess RAP3
• EN 301 489
Max TX power (dBm) per active TX chain (2.4 Ghz)
RX Sensitivity (dBm) (2.4 Ghz)
1Mbps
16
-97
2Mbps
16
-
5.5Mbps
16
-
11Mbps
16
-90
6Mbps
16
-90
9Mbps
16
-
12Mbps
16
-
18Mbps
16
-
24Mbps
16
-
36Mbps
16
-
48Mbps
13
-
54Mbps
11
-75
MCS0/8
16
-90
MCS1/9
16
-
MCS2/10
16
-
MCS3/11
16
-
MCS4/12
16
-
MCS5/13
13
-
MCS6/14
11
-
MCS7/15
10
-72
802.11b
802.11g
802.11n HT20
Maximum capability of the hardware provided. Maximum transmit power will be limited by local regulatory settings.
Figure 1. Antenna gain plots
Azimuth (top) view
330
315
300
285
270
345 5
0
-5
-10
-15
-20
-25
-30
-35
-40
Elevation (front) view
0
15
30
330
45
315
60
75
90
255
105
240
120
225
135
210
Antenna 0
195
180 165
150
Antenna 1
All plots are for channel 6 (2.436 MHz)
Alcatel-Lucent OmniAccess RAP3
Alcatel-Lucent Enterprise Data sheet
3
300
285
270
345 5
0
-5
-10
-15
-20
-25
-30
-35
-40
Elevation (side) view
0
15
30
330
45
315
60
300
75
90
255
105
240
120
225
135
210
195
180 165
150
285
270
345 5 0
0
-5
-10
-15
-20
-25
-30
-35
-40
15
30
45
60
75
90
255
105
240
120
225
135
210
195
180 165
150
Ordering Information
PART NUM BER
DESCRI PTI ON
OAW-RAP3WN
OmniAccess RAP3 Instant Access Point (wireless, 3x10/100Base-T, USB). Unrestricted Regulatory Domain. These
products should be considered as `Rest of World` products and MUST NOT be used for deployments in the United
States, Japan or Israel. Ships with IAP software but can easily be converted to RAP
OAW-RAP3WNP
OmniAccess RAP3P Instant Access Point (wireless, 3x10/100Base-T, USB, POE out). Unrestricted Regulatory
Domain. These products should be considered as `Rest of World` products and MUST NOT be used for
deployments in the United States, Japan or Israel. Ships with IAP software but can easily be converted to RAP.
OAW-RAP3WN-MNT
OmniAccess RAP3WN Series Wall Mount Kit
OAW-AP-CBL-SER
OmniAccess RAP3 Series serial adapter cable (proprietary to DB9 female)
OAW-APAC-48V36
48VDC/36W AC Power Adapter. Note: does not include country specific AC power cord
www.alcatel-lucent.com Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of
Alcatel-Lucent. All other trademarks are the property of their respective owners. The information presented
is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright © 2013 Alcatel-Lucent. All rights reserved. E2013030578EN (March)
Download PDF