York International | DGAH | Service manual | York International DGAH Service manual

USER’S INFORMATION,
MAINTENANCE AND
SERVICE MANUAL
HIGH EFFICIENCY SEALED COMBUSTION
GAS FURNACE
For Installation In:
MODELS: DGAA and DGAH SERIES
(Single Stage Downflow Only)
2. Recreational Vehicles & Park Models
3. Modular Homes & Buildings
1. Manufactured (Mobile) Homes
TABLE OF CONTENTS
CONTACT INFORMATION FOR USA . . . . . . . . . . . . . . . . . . . . . . . 1
CONTACT INFORMATION FOR CANADA . . . . . . . . . . . . . . . . . . . 1
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
While you are away . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SEASONAL SERVICE INFORMATION . . . . . . . . . . . . . . . . . . . . . . 2
Your Service Technician . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
WARRANTY AND RESPONSIBILITIES . . . . . . . . . . . . . . . . . . . . . 2
GAS SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Natural Gas Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Propane Gas Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTRUCTIONS FOR EXAMINING THE
FURNACE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Observing Burner Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
If Furnace Fails to Operate Properly . . . . . . . . . . . . . . . . . . . . . . . 3
HOW YOUR GAS FURNACE WORKS . . . . . . . . . . . . . . . . . . . . . . 4
IF FURNACE FAILS TO OPERATE PROPERLY . . . . . . . . . . . . . . 4
When You Call For Service Assistance . . . . . . . . . . . . . . . . . . . . . 4
To Contact Your Serviceman . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Read the Instructions Below Before Trying
to Start the Furnace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
START-UP AND SHUTDOWN INSTRUCTIONS . . . . . . . . . . . . . . . 4
Operating Instructions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CONTACT INFORMATION FOR USA
•
Contact us by mail:
DISTRIBUTED BY:
Style Crest Inc.
Drawer A
Fremont, OH 43420
•
Manufacturer:
Johnson Controls,
Unitary Products
To Turn Off the Appliance: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
FURNACE USER MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . .5
Air Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Removing Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Blower Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Motor Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
SERVICE AND MAINTENANCE MANUAL . . . . . . . . . . . . . . . . . . . . .6
SAFETY SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
FURNACE MAINTENANCE SECTION . . . . . . . . . . . . . . . . . . . . . .6
FURNACE CLEANING SECTION . . . . . . . . . . . . . . . . . . . . . . . . . .6
Burner Removal/Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Cleaning the Heat Exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
THE FURNACE CONTROLS AND THEIR FUNCTION . . . . . . . . . .6
SEQUENCE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Continuous Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Heating Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Hot Surface Ignition System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
FURNACE CONTROL DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . .8
REPLACEMENT PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
CONTACT INFORMATION FOR CANADA
•
•
Go to website at www.york.com click on “contact”, then click on
“contact form” and follow the instructions.
Contact us by mail:
Johnson Controls Unitary Products
Consumer Relations
5005 York Drive
Norman, OK 73069
The manufacturer recommends that the user read all sections of this manual and keep the manual for future reference.
SECTION I: SAFETY
This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.
Understand and pay particular attention to the signal words DANGER,
WARNING, or CAUTION.
DANGER indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation, which, if not
avoided may result in minor or moderate injury. It is also used to
alert against unsafe practices and hazards involving only property damage.
Johnson Controls Unitary Products
FIRE OR EXPLOSION HAZARD - Failure to follow safety warnings
exactly could result in serious injury, death, or property damage.
—Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
—WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any phone (including
cell phone) in your building.
•
Leave the building immediately.
•
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
•
If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
129099-BUM-K-0613
129099-BUM-K-0613
1. The furnace area must be kept clear and free of combustible materials, gasoline and other flammable vapors and liquids.
2. Insulating materials may be combustible. The furnace must be kept
free and clear of insulating materials. The furnace area must be
examined when installed in an insulated space or when insulation is
added to be sure that the insulation material has been kept away
from the furnace.
3. Follow the instructions exactly as shown on the OPERATING
INSTRUCTION LABEL or the Start-up and Shutdown Instructions
on Page 4 of this manual when lighting the furnace or turning the
furnace off.
4. Should the gas supply fail to shut off or if overheating occurs, shut
off the gas valve to the furnace before shutting off the electrical supply.
5. Do not use this furnace if any part has been under water. A flooddamaged furnace is extremely dangerous. Attempts to use the furnace can result in fire or explosion. A qualified service agency
should be contacted to inspect the furnace and replace all gas controls, control system parts, electrical parts that have been wet or the
furnace if deemed necessary.
6. NEVER…Store flammable materials of any kind near your furnace.
Gasoline, solvents, and other volatile liquids should be stored only in
approved containers outside your home. These materials vaporize
easily and are extremely dangerous.
7. NEVER
Store cleaning materials near your furnace. Materials
such as bleaches, detergents, powdered cleansers, etc., can cause
corrosion of the heat exchangers.
Use the area around your furnace as a storage area for
8. NEVER
items which could block the normal flow of air. This flow of air is
required for ventilation of the various furnace components.
Your Service Technician
Your furnace's best friend is your qualified service technician. If the unit
gives any indication of improper operation, call your service technician.
If the service technician is allowed to perform the normal routine care of
your furnace, he can many times detect potential difficulties and make
corrections before trouble develops. Preventative maintenance of this
type will allow you to operate the unit with a minimum of concern, and at
the same time will pay for itself in added years of comfort.
DESCRIPTION
This furnace shall be installed in the downflow position. Figure 1 shows
a typical model in the downflow position. The furnace is equipped with
an induced-draft vent blower and atmospheric burner. Combustion air is
drawn through the roof jack and pushed into the burner box. Flue gas is
forced from the heat exchanger by the vent blower and discharged
through the flue pipe to the outside atmosphere.
This is a forced air furnace. The furnace circulating air blower draws
cool air from the house, passes it over the hot furnace heat exchanger
and circulates the warmed air through the ductwork to the house.
The furnace is equipped with the controls necessary for proper operation. The various components referred to in this manual and on the furnace rating plate are identified in Figure 1.
…
…
VENT PIPE
FLUE
COLLAR
BLOWER MOTOR
CAPACITOR
BLOWER
BLOWER
MOTOR
COMBUSTION
AIR PIPE
PRESSURE
SWITCH
FIRE OR EXPLOSION HAZARD
This furnace is designed and approved for use with Natural Gas
and (LP) Propane Gas ONLY. DO NOT BURN ANY LIQUID FUEL
OR SOLID FUEL IN THIS FURNACE.
Burning any unapproved fuel will result in damage to the furnace heat
exchanger, which could result in Fire, Personal Injury, and/or Property
Damage.
While you are away
Your furnace is equipped with a safety device which will shut off the
supply of gas to the burner in case of malfunction. For this reason it is
never practical to assume that the furnace will operate unattended for a
long period of time, especially if there is a possibility of damage to your
property because of freezing. So, if you plan to be away from home,
arrange for someone to check your house every day.
SEASONAL SERVICE INFORMATION
During extreme cold weather, ice may form on the furnace roof jack
crown. Small amounts of ice forming on the roof jack will present no
problem to proper furnace operation. However, excessive ice formation
could restrict the combustion air supply to the burner causing inefficient
burner operation.
When the temperature is very cold, near zero or below, it is recommended that the roof jack be inspected every day or more frequently if
required. If ice has started to collect on the roof jack crown, it should be
carefully broken off.
SAFETY SHUTOFF
SWITCH
CONTROL
BOARD
BOOSTER DRAFT
ASSEMBLY
SILICONE
TUBE
GAS VALVE
GAS BURNER
ASSEMBLY
AIR CONDITIONING
COIL PANELS
FIGURE 1: Component Locations
WARRANTY AND RESPONSIBILITIES
It is the sole responsibility of the home owner to make certain that the
gas furnace has been correctly set up and converted to the proper fuel
(Propane or Natural gas) and adjusted to operate properly.
The manufacturer warrants the furnace to be free from defects in material or workmanship for the stated time in the warranty agreement (see
warranty certificate packed with the furnace).
However, the manufacturer will not be responsible for any repair costs
to correct problems due to improper set-up, improper installation, furnace adjustments, improper operating procedure by the user, etc.
It is also the sole responsibility of the home owner to make sure that the
home if located above 2,000 ft. altitude be derated.
2
Johnson Controls Unitary Products
129099-BUM-K-0613
Some specific examples of service calls which cannot be included in
warranty payments are:
1. Converting the furnace to use another type of fuel.
2.
3.
4.
5.
Correcting faulty duct work in the home.
Correcting wiring problems in the electrical circuit to the furnace.
Resetting circuit breakers or other switches.
Adjusting the burner air shutter or service calls made to correct
problems caused by improper air adjustment.
6. Correcting problems caused by improper gas supply pressure to the
furnace.
7. Instructional training on how to light and operate furnace.
8. Furnace problems caused by installation of air conditioner, heat
pump, or other air quality device.
9. Problems caused by improper installation of the furnace flue assembly (roof jack).
10. Adding a roof jack extension because of unusual wind conditions or
snow conditions.
11. Adjusting thermostats.
12. Problems caused by construction debris which has fallen into the
flue or combustion air openings.
13. Replacement of fuses.
14. Problems caused by plugged or restricted orifices by any means.
You should establish a firm understanding of these responsibilities with
your manufactured housing dealer, service company or gas supplier so
there will be no misunderstanding at a later time.
GAS SUPPLY
The gas supply to your home will either be Natural Gas or Propane gas.
Your furnace will be factory equipped to operate on only one of these
two different gases.
A small metal tag secured to the furnace next to the gas valve will specify the type of gas your furnace is equipped to use.
If the gas is different from that specified on the metal tag, the furnace
can be converted by following the instructions on the furnace safety
label inside lower front panel. Parts for conversion are contained in the
small bag attached to the gas valve. Be sure the proper size orifice is
used, as specified on the furnace name plate.
The furnace must be converted by a qualified technician. Improper
conversion can cause unsafe operation, explosion, and/or fire or
asphyxiation.
Natural Gas Operation
The furnace is designed for 7" W.C. inlet pressure. Pressure is reduced
to 3-1/2” W.C. by the pressure regulator in the gas valve.
Propane Gas Operation
Inlet pressure to the gas valve must be 11" W.C. When properly converted to Propane gas, the pressure is regulated at 10" W.C.
INSTRUCTIONS FOR EXAMINING THE FURNACE
INSTALLATION
It is the owner’s responsibility to ensure that an annual inspection of the
entire heating portion of the unit is made by a qualified service agency.
Examine the furnace as outlined below in steps “1 - 6” before each
heating season.
1. Examine the heat exchanger, through an access panel located on
the supply air plenum. Visually examine the exterior sections of the
vent/combustion air piping and the vent connectors to be sure that
they are physically sound without holes or excessive corrosion.
Johnson Controls Unitary Products
2. Examine the vent pipe making sure it is firmly in place, and is physically sound without holes and all of the connections are secure.
3. Examine return connections for Modular or Manufactured (Mobile)
Homes.
4. Examine the return air filter rack connections to make sure they are
physically sound, sealed to the furnace door.
5. Examine the furnace casing making sure the physical support is
sound without sagging, cracks or gaps. Examine the furnace base
making sure it is physically sound without cracks, gaps or sagging
and has a good seal.
6. Examine the furnace casing for obvious signs of deterioration.
7. Examine the burner flames to make sure the burner look like they
are operating properly. The burner flames for natural gas should
appear blue with a few yellow tips. The burner flames for propane
gas should appear blue with moderate yellow tips. The flame should
appear cylindrical in shape and should extend from the end of the
burner into the heat exchanger.
PROPANE GAS
NATURAL GAS
LIGHT BLUE
WITH YELLOW TIPS
WHITISH YELLOW
TO LIGHT YELLOW
DARK BLUE
LIGHT BLUE
BLUE TIPS JUST
STARTING TO
BECOME
PRONOUNCED
BLUE TIPS JUST
STARTING TO
BECOME
PRONOUNCED
FIGURE 2: Burner Flame Appearance
Observing Burner Operation
1. Observe burner to make sure it ignites. Observe color of flame. On
natural gas the flame will burn blue with appreciably yellow tips. On
Propane gas a yellow flame may be expected. If flame is not the
proper color call a qualified service technician for service.
2.
3.
4.
5.
Let furnace heat until blower cycles on.
Turn thermostat down.
Observe burner to make sure it shuts off.
Let the furnace cool and blower cycle off.
Should overheating occur, or the gas supply fail to shut off, shut off
the manual gas valve to the furnace and allow blower to run until furnace cools down and blower shuts off before shutting off the electrical
supply.
If any abnormalities are observed when checking for correct operation,
such as burner failing to ignite or to turn off, sooty flame, etc., call your
nearest authorized service technician as shown in the Service Center
List included in the home owner envelope with the furnace.
If Furnace Fails to Operate Properly
1. Check setting of thermostat - and position of HEAT/COOL switch if
air conditioning is installed. If a set-back type thermostat is
employed be sure that the thermostat is in the correct operating
mode.
2. Check to see that electrical power is ON.
3. Check to see that the knob or switch on the gas control valve is in
the full ON position.
4. Make sure filters are clean, return grilles are not obstructed, and
supply registers are open.
5. Be sure that furnace flue piping is open and unobstructed.
If the cause for the failure to operate is not obvious, do not attempt to
service the furnace yourself. Call a qualified service agency or your gas
supplier.
3
129099-BUM-K-0613
1. Examine Vent Pipe
2. Examine Filter Door
All appliances need maintenance by serviceman at the beginning of
each heating season. Call your nearest authorized service technician
to:
1. Replace filters. Clean all lint and dust from around furnace.
3. Remove Filter
Door to Examine
Combustion Air Pipe
7. Remove Burner
Door to Examine
Burner Flame
2. Remove fan and clean all dust and lint from unit with stiff bristle
brush.
3. Inspect combustion chamber, the transition into the blower compartment, flue collar, and roof jack.
4. Check the gas valve and line connections for leaks.
5. Make any adjustments necessary for good operation.
NOTICE
4. Examine Burner Door
The coil panel provides a good removable access for inspecting
inside the furnace casing. Smoke or reflected light inside the casing
indicates the presence of leaks in the heat exchanger.
5. Remove Burner
Door to Examine
Furnace Base and
Air Conditioning
Coil Panels
SAFETY INFORMATION
Read the Instructions Below Before Trying to Start the
Furnace
FIGURE 3: Furnace Examination Checkpoints
HOW YOUR GAS FURNACE WORKS
Your furnace is a very easy appliance to take for granted. Season after
season, it sits there in your home, keeping you warm and comfortable.
For this reason, you may never have given much thought to the way
your furnace operates. In order to get the safest and most efficient operation from your furnace, you should understand how your furnace does
its job.
When you set your thermostat to provide more heat in your home, you
are starting the heating cycle of the furnace. First, the inducer motor
starts to purge the heat exchanger of any remaining gases. Next, the
hot surface ignitor glows and after a warm-up period the gas valve
opens and ignition occurs. A short time later, the blower starts and distributes the warm air throughout the home. When the temperature setting on your thermostat is reached, the gas valve closes, the main
burner is turned off, and the blower continues to run until the remaining
warm air in the system is distributed. When the blower stops, the heating cycle has ended.
IF FURNACE FAILS TO OPERATE PROPERLY
1. Check setting of thermostat - and position of heat/cool switch if air
conditioning is installed. If a set-back type thermostat is employed
be sure that the thermostat is in the correct operating mode.
2. Check to see that electrical power is “ON”.
3. Check to see that the lever or switch on the gas control valve is in
the full “ON” position.
4. Make sure filters are clean, return grilles are not obstructed, and
supply registers are open.
5. Be sure that furnace flue piping is open and unobstructed.
When You Call For Service Assistance
Very often time can be saved if you will give the service agency the
MODEL and SERIAL NUMBER of your furnace. This will enable him to
determine the specific components used, and perhaps to better identify
the possible problem and be better prepared if a service call is required.
To Contact Your Serviceman
(fill in)
COMPANY: ______________________________________________
ADDRESS: ______________________________________________
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury, and/or loss of life.
1. This appliance does not have a pilot. It is equipped with an ignition
device which automatically lights the burner. Do not try to light the
burner by hand.
2. BEFORE OPERATING; smell all around the appliance area for gas.
Be sure to smell next to the floor because some gas is heavier than
air and will settle on the floor.
3. Use only your hand to push the gas control switch to the “on” position. Never use tools. If the switch will not operate by hand, don’t try
to repair it, call a qualified service technician. Force or attempted
repair may result in a fire or explosion.
4. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control system and any gas control, which
has been under water.
START-UP AND SHUTDOWN INSTRUCTIONS
Operating Instructions:
1. STOP! Read the safety information above.
2.
3.
4.
5.
Set the thermostat to the lowest setting.
Turn off all electric power to the appliance.
Remove furnace door.
Move gas control switch to the “OFF” position. Do not force. See
Figure 4.
6. Wait five (5) minutes to clear out any gas. If you then smell gas,
STOP! Follow Step 2 (refer to Safety Information on Page 4). If you
don’t smell gas, go to next step.
7. Move gas control switch to the “ON” position. Do not force. See Figure 4.
8. Replace burner door.
9. Turn on all electric power to the appliance.
10. Set thermostat to the desired setting. Burner will light, which may
take 30-60 seconds.
11. After three (3) trials for ignition, if the appliance will not operate follow the instructions, “TO TURN OFF THE APPLIANCE” and call
your service technician or gas supplier.
TELPHONE: _____________________________________________
4
Johnson Controls Unitary Products
129099-BUM-K-0613
To Turn Off the Appliance:
Every time the filters are changed the following items should be visually
inspected:
1. Set the thermostat to lowest setting.
2. Turn off all electric power to the appliance if service is to be performed.
3. Remove burner access panel.
4. Move gas control switch to the “OFF” position. See Figure 4.
5. Replace burner access panel.
Should overheating occur, or the gas valve fail to shut off, turn the
external manual gas valve in the gas supply line to the furnace to the
“off” position and let the furnace cool off before shutting off the electrical power supply. Refer to Figure 5.
MAIN REGULATOR
ADJUSTMENT
90°
FLANGE
OUTLET (MANIFOLD)
PRESSURE TAP
INLET
• Check roof jack assembly for blockage or leakage.
• Check all components to be sure they are in good condition and
that there are no obvious signs of deterioration.
• Check the evaporator coil drain lines to make sure there are no
cracks or leaks.
• Check for dirt or lint on any surfaces or on components. Do not try
to clean any of the surfaces or components. Cleaning of the furnace and its components must be done by a qualified service professional.
If, during the inspection of your furnace, you find any of the following
conditions:
•
•
•
•
Excessive amounts of dust and lint on components.
Damaged or deteriorated components or surfaces.
Leaks or blockage in the vent pipe passages.
Water on any surface inside or outside of the furnace.
Do not operate the furnace, and call a certified dealer / servicing contractor to check and / or clean your furnace, or for more information if
you have questions about the operation of your furnace.
If all components appear to be in good operating condition, replace the
front panels. Follow the operating instructions to place the furnace in
operation.
SUPPLY
PRESSURE
TAP
Air Filters
ELECTRICAL
CONNECTIONS
ON/OFF SWITCH
(shown in OFF position)
OUTLET
FIGURE 4: Gas Valve
Dirty filters greatly restrict the flow of air and may cause damage to the
moving parts of the furnace. If the filters become clogged the heat
exchangers and blower motor could overheat resulting in a potentially
dangerous situation.
The filters should be checked every 3 months (DO NOT USE PLEATED
FILTER in this furnace). On new construction, check the filters every
week for the first four weeks and every three weeks after that, especially if the indoor fan is running continuously. When replacing the filter(s) you must use filters that are the same size and type as those in
the furnace (2 - 16 x 20 x1).
Removing Filters
GAS
PIPE
Internally Mounted Air Filters
GAS
PIPE
MANUAL
SHUT-OFF
VALVE
The air filter is in a rack that is attached to the door of the furnace.
To remove the filter you must do the following:
GAS
BURNER
GAS
VALVE
DRIP
LEG
MANUAL
SHUT-OFF
VALVE
DRIP
LEG
FIGURE 5: Gas Piping
FURNACE USER MAINTENANCE
Before proceeding, be sure the area is well ventilated. Turn the thermostat OFF. If the blower is running, wait until it stops automatically.
Turn OFF the gas and electrical power supplies to the furnace. Check
all metal parts and surfaces to be sure they have cooled to room temperature before you begin.
Johnson Controls Unitary Products
1. Before proceeding, be sure the area is well ventilated. Follow
instruction “To turn off the appliance”. Check all metal parts and surfaces to be sure they have cooled to room temperature before you
begin.
2. Remove the filter door.
3. Remove the air filter by sliding it down the track. The air filter will
slide out of the rack.
4. Replace throw away filter(s) with the same size new filter(s). Throw
away filter(s) may be replaced with cleanable filter(s) at this time.
Cleanable filter(s) may be cleaned as described in the manufacturer
instructions or as described in these instructions.
To replace the filter after cleaning you must do the following:
1. Slide filter into place. If the filter has been cleaned, make sure it is
dry before re-installing it.
2. Replace the door or cover panel.
3. Make sure the door snaps into the retaining clips.
4. Follow the Operating Instructions to place the furnace back in operation.
5
129099-BUM-K-0613
Blower Care
Burner Removal/Cleaning
Even with good filters properly in place, blower wheels and motors will
become dust laden after long months of operation. The entire blower
assembly should be inspected annually. If the motor and wheel are
heavily coated with dust, they can be brushed and cleaned with a vacuum cleaner. If the blower cannot be properly cleaned without removing
it from the furnace, then call a qualified service agency. Only a qualified
service agency can perform this service.
The main burner should be checked periodically for dirt accumulation. If
cleaning is required, follow this procedure:
Make sure you DO NOT move the clip on weight on the indoor fan
wheel when cleaning the wheel. This weight is used to balance the
wheel. Moving the weight will cause the fan wheel to vibrate.
Motor Lubrication
1. Turn off the electrical power to the unit.
2. Turn off the gas supply at the external manual shut-off valve and
loosen the ground union joint.
3. Remove the upper access panel.
4. Disconnect wires from flame sensor, rollout switch and HSI igniter.
Remove igniter carefully, as it is easily broken.
5. Remove the screws that hold the burner assembly to the combustion air box and remove the assembly.
6. Remove burner from the burner assembly.
7. Rinsing in hot water may clean burners.
8. Reassemble in the reverse order.
Cleaning the Heat Exchanger
The motors in these furnaces are permanently lubricated, and do not
require periodic oiling.
SECTION II: SERVICE AND MAINTENANCE
MANUAL
SAFETY SECTION
This section has been designed to assist a qualified service agency in
performing service and maintenance on this appliance. The homeowners and/or end user must never attempt to perform any service or maintenance on the appliance especially when it involves the removal or
adjustment of any parts and/or components.
The following safety rules must be followed when servicing the furnace.
ELECTRIC SHOCK, FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in dangerous
operation, serious injury, death or property damage.
Improper servicing could result in dangerous operation, serious injury,
and death or property damage.
• Before servicing, disconnect all electrical power to the furnace.
• When servicing controls, label all wires prior to disconnecting.
Reconnect wires correctly.
• Verify proper operation after servicing.
NOTICE
It is recommended that replacement gaskets be available before
removing burner assembly and combustion air box.
Lower Heat Exchanger Access
1. Turn off the electrical power to the unit and turn off gas supply at the
shutoff valve.
2. Remove the blower and burner compartment access doors. Disconnect the gas supply piping at the union to permit removal of the
entire burner and gas control assembly from the vestibule panel.
Use the wrench boss on the gas valve when removing or installing
this piping.
3. Unplug the igniter from the wire harness. Disconnect sensor wires.
Identify and note the location of all leads for ease of reinstallation.
4. Remove the screws holding the burner assembly to the vestibule
panel and remove this assembly. Handle the assembly carefully
since it contains the igniter, which is fragile and easily broken. The
lower portion of the heat exchanger will now be exposed. Remove
any soot and scale. Vacuum loose soot, scale and dirt from the heat
exchanger.
5. After cleaning is complete, replace all components in reverse order.
Re-gasket all surfaces which required a gasket. Reconnect all wiring. Reattach vent pipe and gas supply lines before restoring service
to furnace. Restore electrical power, check gas supply piping for
leaks, and then verify furnace operation.
FURNACE MAINTENANCE SECTION
The furnace should be cleaned and adjusted by a certified dealer or
qualified service contractor once a year or before the start of every
heating season. The following items must be cleaned and serviced or
replaced if there are signs of deterioration.
1. The roof cap (if applicable).
2. The furnace vent pipe. Should it be necessary to service the vent/air
intake system, the manufacturer recommends this service be conducted by a qualified service agency. The operation of this appliance
requires the reassembly and resealing of the vent/air intake system.
3. The furnace burner, ignitor and flame sensor.
FURNACE CLEANING SECTION
NOTICE
The cleaning operations listed below must be performed only by a
qualified service agency.
6
Label all wires prior to disconnection when servicing controls. Wiring
errors can cause improper and dangerous operation. Verify proper
operation after servicing.
THE FURNACE CONTROLS AND THEIR FUNCTION
1. Limit Control - This furnace is protected by two (2) high temperature limit switches. The lower limit switch is an automatic reset type.
2. Upper Limit Control - The upper limit switch near left side of blower
is a manual reset type limit switch. If burner does not function, turn
system switch to “OFF” and push reset button in center of limit
switch.
3. Gas Valve - The gas valve is 100% shut-off type and will fail safe if
for some reason the gas is turned off. It is also of the snap opening
type which opens to fire position.
Johnson Controls Unitary Products
129099-BUM-K-0613
SEQUENCE OF OPERATION
TRANSFORMER
Continuous Blower
LINE VOLTAGE
On cooling/heating thermostats with fan switch, when the fan switch is
set in the ON position, a circuit is completed between terminals R and G
of the thermostat. The blower motor is energized through the cool fan
terminal on the ignition control module.
COOL
HEAT
NEUTRALS
Intermittent Blower - Cooling
L1
XFMR
BLACK - HIGH SPEED
RED -LOW SPEED
On cooling/heating thermostats with fan switch, when the fan switch is
set in the auto position and the thermostat calls for cooling, a circuit is
completed between the R, Y and G terminals. The motor is energized
through the cool fan terminal and runs on the selected speed. The fan
off setting is fixed at 60 seconds for SEER enhancement.
Heating Cycle
When the system switch is set on HEAT and the fan is set on AUTO,
and the room thermostat calls for heat, a circuit is completed between
terminals R and W of the thermostat. When the proper amount of combustion air is being provided, a pressure switch activates the ignition
control.
The ignition control provides a 30-second warm-up period. The gas
valve then opens for 10 seconds. If the flame is not detected within 2
seconds of the gas valve opening, the gas valve is shut off and a retry
operation begins. If the flame is lost for 2 seconds during the 10 second
stabilization period, the gas valve is shut off and a retry operation
begins. During a retry operation the ventor starts a 15 second interpurge and the ignitor warm-up time is extended to 27 seconds. If the
flame is established for more than 10 seconds after ignition, during a
retry, the control will clear the ignition attempt (retry) counter. If three
retries occur during a call for heat, the furnace will shut down for one
hour. If at the end of the one hour shut down there is a call for heat, the
furnace will initiate a normal start cycle. If the problem has not been corrected the furnace will again lockout after three retries.
A momentary loss of gas supply, flame blowout, or a faulty flame probe
circuit will result in a disruption in the flame and be sensed within 0.8
seconds. The gas valve will de-energize and the control will begin a
recycle operation. A normal ignition sequence will begin after a 15 second inter-purge. If during the three recycles the gas supply does not
return, or the fault condition is not corrected the ignition control will lockout for 60 minutes.
During burner operation, a momentary loss of power for 50 milliseconds
or longer will de-energize the gas valve. When the power is restored,
the gas valve will remain de-energized and the ignition sequence will
immediately restart.
As the gas starts to flow and ignition occurs, the flame sensor begins its
sensing function. If a flame is detected during the 10 second flame stabilization period the circulating blower will energize 30 seconds after the
gas valve opens (20 seconds after the flame stabilization period ends).
Normal furnace operation will continue until the thermostat circuit
between R and W is opened. When the thermostat circuit opens, the
ignition control is de-energized. When the ignition control is de-energized, the gas flow stops, and the burner flames are extinguished. The
ventor continues to operate for 15 seconds after the gas flow stops.
The blower motor continues to operate for the amount of time set by the
fan-off delay “Jumper” located on the ignition control board. Refer to
Figure 6. The heating cycle is complete, and the furnace is ready for the
start of the next heating cycle.
FAN OFF
JUMPER
FAN ON
ADJUSTMENT
JUMPER
FUSE 3A
FIGURE 6: Furnace Control Board
Hot Surface Ignition System
HOT SURFACE IGNITION SYSTEM
Do not attempt to light this furnace by hand (with a match or any other
means). There may be a potential shock hazard from the components
of the hot surface ignition system. The furnace can only be lit automatically by its hot surface ignition system.
TROUBLESHOOTING
The following visual checks should be made before troubleshooting:
1. Check to see that the power to the furnace and the ignition control
module is ON.
2. The manual shut-off valves in the gas line to the furnace must be
open.
3. Make sure all wiring connections are secure.
4. Review the sequence of operation. Start the system by setting the
thermostat above the room temperature. Observe the system’s
response. Then use the troubleshooting section in this manual to
check the system’s operation.
Never bypass pressure switch to allow furnace operation. To do
so will allow furnace to operate under potentially hazardous conditions.
Do not try to repair controls. Replace defective controls with
UPG Source 1 Parts.
Never adjust pressure switch to allow furnace operation.
Johnson Controls Unitary Products
7
129099-BUM-K-0613
FURNACE CONTROL DIAGNOSTICS
The furnace has built-in, self diagnostic capability. If a system problem
occurs, a fault code is shown by a blinking green LED. It is located
behind a clear view port in the blower compartment door. DO NOT turn
off furnace power as this action will clear the control's memory of the
fault.
The control continuously monitors its own operation and the operation
of the system. If a failure occurs, the LED will indicate the failure code. If
the failure is internal to the control, the light will stay on continuously. In
this case, the entire control should be replaced as the control is not field
repairable.
Flash sequence codes 1 through 6 are as follows: LED will turn “on” for
one second and “off” for one second. This pattern will be repeated the
number of times equal to the code. For example, six “on” flashes equals
a number 6 fault code.
3 FLASH: Combustion air pressure switch failed to close, this indicates
the normally open pressure switch contact did not close at the beginning of the heat cycle. This could be caused by a number of problems;
faulty inducer, blocked vent pipe, broken pressure switch hose or faulty
pressure switch.
4 FLASH: Limit Switch Open, this indicates that a primary or auxiliary
limit switch has opened its normally closed contacts. With this fault code
the control will operate the supply air blower and inducer. This condition
may be caused by: dirty filter, improperly sized duct system, incorrect
blower speed setting, incorrect firing rate or faulty blower motor.
5 FLASH: Gas flow with no call for heat. Check gas valve and gas valve
wiring.
RAPID FLASHES: Reverse Polarity, reverse polarity indicates reverse
line voltage polarity. Both heating and cooling will be affected. Check
polarity of both.
STEADY ON: Normal Operation.
All flash code sequences are broken by a 2 second “off” period.
60 MINUTE AUTOMATIC RESET FROM LOCKOUT: This control
includes a “watchdog” type circuit that will reset from a lockout condition
after 60 minutes. Operational faults 1, 3, 4 and Steady On will be reset.
This provides protection to an unoccupied structure if a temporary condition exists causing a furnace malfunction. An example would be a low
incoming gas supply pressure preventing unit operation. When the gas
pressure is restored, at some point the “watchdog” would restart the unit
and provide heat for the house.
IGNITION CONTROL
Normal flame sense current is approximately
3.7 microamps DC (a)
Low flame signal control lockout point is
0.9 microamps DC (a)
1 FLASH: Ignition failure.
2 FLASH: Combustion air pressure switch closed, this indicates that the
normally open pressure switch contacts are stuck in the closed position.
The control confirms these contacts are open at the beginning of each
heat cycle. This would indicate a faulty pressure switch or mis-wiring.
NOTICE
If a flame is detected the control flashes the LED for 1/8 of a second
and then enters a flame stabilization period.
Thermostat Satisfied
Thermostat Calling for Heat
(Seconds)
0 5
0
32
Fan on Delay
12 Seconds
ON
THERMOSTAT
OFF
OFF
ON
INDUCER
OFF
15 Sec.
Post
Purge
ON
IGNITOR
OFF
OFF
OFF
OFF
MAIN VALVE
OFF
CIRCULATING
BLOWER
OFF
ON
OFF
OFF
60, 90, 120, 180 SEC. OFF
Selectable Fan Off Delay
FIGURE 7: Furnace Event Control Schedule
8
Johnson Controls Unitary Products
129099-BUM-K-0613
SECTION III: REPLACEMENT PARTS LIST
All components, assemblies, accessories, and replacement parts for this furnace are available through your qualified service installer or refer to the
service center list in your booklet. It is not recommended that the homeowner purchase, install, or replace any components of this furnace. Contact
your local contactor, dealer, or service provider for additional information.
DGAA
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
DESCRIPTION
DGAA056BDTB
DGAA070BDTB
DGAA077BDTB
DGAA090BDTB
Switch, Pressure
Tubing Silicone (2’ Req’d)
S1-32435972000
S1-02812499000
S1-02535358000
S1-37319801821
S1-03101932002
S1-02543267000
S1-07319801064
S1-32435972000
S1-02812499000
S1-02535358000
S1-37319801821
S1-03101932002
S1-02543267000
S1-07319801064
S1-32435972000
S1-02812499000
S1-02535358000
S1-37319801821
S1-03101932002
S1-02543267000
S1-07319801064
S1-32435972000
S1-02812499000
S1-02535358000
S1-37319801821
S1-03101932002
S1-02543267000
S1-07319801064
S1-37319804651
S1-02535354000
S1-7681-3301
S1-2940A3541
S1-02535380000
S1-37319801403
S1-37323792001
S1-02535354000
S1-7681-3301
S1-2940A3541
S1-02535380000
S1-37319801403
S1-37323792002
S1-02535354000
S1-7681-3301
S1-2940A3541
S1-02535381000
S1-37319801403
S1-37323792003
S1-02535354000
S1-7681-3301
S1-2940A3541
S1-02535381000
S1-37319801403
S1-02541021000
S1-1214-2511
S1-02541021000
S1-02541021000
S1-1214-2511
S1-1214-2511
Accessory (See Page 4)
7900-7611
7900-7611
S1-1468-220P
S1-1468-220P
S1-02435603000
S1-02435603000
S1-37319806100
S1-37319806100
S1-02521192000
S1-02521192000
S1-02420063000
S1-02420063000
S1-02435602000
S1-02435602000
S1-02435813000
S1-02435813000
S1-02619654003
S1-02619654003
S1-07319801342
S1-07319801342
155887
155887
S1-02118364000
S1-02118364000
S1-02118365000
S1-02118365000
S1-37323864001
S1-37323864001
S1-01006900005
S1-01006900005
S1-01006742000
S1-01006742000
S1-01006900015
S1-01006900015
S1-01006900001
S1-01006900001
S1-02541021000
S1-1214-2511
Limit Switch, Manual (Upper)
Assembly, Booster (w/Motor)
Control Board, Integrated
Valve, Gas
Bracket, Mounting (Gas Valve)
14
15
16
17
18
19
20
21
22
23
24*
25*
26*
27*
28*
29*
30*
31*
32*
NOTE:
Exchanger, Heat (w/Gaskets)
Sensor, Flame
Switch, System
Transformer (115-24V, 40 VA)
Switch, Limit
Burner Assembly, Auto Ignition
(Includes items 10 & 15)
Ignitor, Hot Surface
Filter (2 Req’d) (16x20x1)
Panel, Door (Upper)
Panel, Door (Lower, Tall)
Motor (See Note 2) (old-see note 4)
Motor
(new-see note 4)
Assembly, Motor Mount (See Note 2)
Plug, Connector
Capacitor, Run (See Note 3) (Old-see note 4)
Capacitor
(New-see note 4)
Capacitor (Units built on/after 8/11/2008)
Wheel, Blower
Top, Casing
Diagram, Wiring
Strike, Door
Latch, Door
Housing, Blower
Gasket, Combustion Air Box
Gasket, Burner
Gasket, Booster Assembly
Gasket, Heat Exchanger
7900-7611
S1-1468-220P
S1-02435603000
S1-37319806100
S1-02521192000
S1-02420063000
S1-02435602000
S1-02435813000
S1-02619654003
S1-07319801342
155887
S1-02118364000
S1-02118365000
S1-37323864001
S1-01006900005
S1-01006742000
S1-01006900015
S1-01006900001
<
<
7900-7611
S1-1468-220P
S1-02435603000
S1-37319806100
S1-02521192000
S1-02420063000
S1-02435602000
S1-02435813000
S1-02619654003
S1-07319801342
155887
S1-02118364000
S1-02118365000
S1-37323864001
S1-01006900005
S1-01006742000
S1-01006900015
S1-01006900001
*Not Shown
New replacement parts shown in bold face type at the first printing of parts list dated 1/12.
Major components and suggested stocking items are shown with shaded item number.
“<“Across from row indicates a change in that row.
--- Not applicable to specified model.
2. For Serial Numbers lower then 001207164- Replacement DGAA motors also require Motor Mount
Assembly 373-19806-100 if replaced motor has integral, flex-arm motor mount.
3. DGAA with 5-Ton Blowers are provided as an accessory item and are not standard equipment from
the factory. See Page 4
4. The “old” motor must use the “old” run capacitor. The “new” motor can use either capacitor.
Serial No. W0F6528688 and above were built with the new motor.
Johnson Controls Unitary Products
9
129099-BUM-K-0613
WIRING DIAGRAM
DGAH
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24*
25*
26*
27*
28*
29*
30*
31*
32*
DESCRIPTION
DGAH056BBSB
DGAH077BBSB
Switch, Pressure
Tubing Silicone (2’ Req’d)
S1-32435972000
S1-02812499000
S1-02535358000
S1-37319801821
S1-03101932002
S1-02543267000
S1-07319801064
S1-32435972000
S1-02812499000
S1-02535358000
S1-37319801821
S1-03101932002
S1-02543267000
S1-07319801064
S1-37319804651
S1-02535354000
S1-7681-3301
S1-2940A3541
S1-02535380000
S1-37319801403
S1-37323792002
S1-02535354000
S1-7681-3301
S1-2940A3541
S1-02535381000
S1-37319801403
S1-02541021000
S1-1214-2511
S1-02541021000
S1-1214-2511
Limit Switch, Manual (Upper)
Assembly, Booster (w/Motor)
Control Board, Integrated
Valve, Gas
Bracket, Mounting (Gas Valve)
Exchanger, Heat (w/Gaskets)
Sensor, Flame
Switch, System
Transformer (115-24V, 40 VA)
Switch, Limit
Burner Assembly, Auto Ignition
(Includes items 10 & 15)
Ignitor, Hot Surface
Filter (2 Req’d) (16x20x1)
Panel, Door (Upper)
Panel, Door (Lower, Short)
Motor
Assembly, Motor Mount
Plug, Connector
Capacitor, Run
Wheel, Blower
Top, Casing
Diagram, Wiring
Strike, Door
Latch, Door
Housing, Blower
Gasket, Combustion Air Box
Gasket, Burner
Gasket, Booster Assembly
Gasket, Heat Exchanger
<
<
Accessory (See Page 4)
7900-7671
S1-02431948000
--S1-02521192000
--S1-02619654003
S1-07319801342
157953
S1-02118364000
S1-02118365000
S1-37323864001
S1-01006900005
S1-01006742000
S1-01006900015
S1-01006900001
7900-7671
S1-02431948000
--S1-02521192000
--S1-02619654003
S1-07319801342
157953
S1-02118364000
S1-02118365000
S1-37323864001
S1-01006900005
S1-01006742000
S1-01006900015
S1-01006900001
NOTE:
*Not Shown
New replacement parts shown in bold face type at the first printing of parts list dated 1/12.
Major components and suggested stocking items are shown with shaded item number.
“<“Across from row indicates a change in that row.
--- Not applicable to specified model.
3. DGAH with 5-Ton Blowers are provided as an accessory item and are not standard equipment from
the factory. See page 4.
BURNER ORIFICE CHART (Normal Altitude Only, See Note 5)
MODEL
056
070
077
090
NATURAL GAS
LP GAS
S1-9951-1361
S1-9951-0821
S1-9951-1541
S1-9951-0931
S1-9951-1611
S1-9951-0981
S1-9951-1771
S1-9951-1061
ACCESSORY PARTS LIST
ACCESSORY
5-Ton Blower Ass’y
7900-7751
DESCRIPTION
Door Panel (Upper)
Motor
Run Capacitor (20 MFD)
Motor Mount
Blower Wheel
DGAA
DGAH
7900-7631
S1-02431975000
S1-02420051000
S1-37319802930
S1-1472-2761
7900-7631
S1-02431975000
S1-02420051000
S1-37319802930
S1-1472-2761
NOTES
5 Contact Customer Service for installations at altitudes over 2000 feet above sea level.
“<“Across from row indicates a change in that row.
--- Not Applicable to specified model.
10
Johnson Controls Unitary Products
129099-BUM-K-0613
FIGURE 8: Wiring Diagram - DGAA
Johnson Controls Unitary Products
11
129099-BUM-K-0613
FIGURE 9: Wiring Diagram - DGAH
12
Johnson Controls Unitary Products
129099-BUM-K-0613
Limited Warranty
Manufactured Housing Furnaces
WARRANTY TERMS: Johnson Controls Unitary Products (hereinafter “Company”) warrants this product to be free from defects in factory workmanship and material under normal use and service and will, at its option, repair or replace any parts, without charge, subject to the exclusions below,
that prove to have such defects according to the terms outlined in this warranty. Company reserves the right, at its sole discretion, to provide a
replacement unit in the place of repair parts, in which case the warranty period for the replacement unit is limited to the remainder of the original warranty period. Alternatively, Company may, at its option, extend a replacement allowance to be applied toward the purchase of a new unit marketed by
Company. The exact amount of the allowance will be determined at the discretion of Company, based upon current market conditions, but in no case
shall this allowance exceed thirty (30) percent of the original consumer purchase price of the unit excluding such items as ductwork, wiring, piping,
and installation costs. The warranty period for repair or replacement parts or unit provided hereunder shall not extend beyond the warranty period
stated below. Company shall have no responsibility hereunder for installation, shipping, handling, or other charges except as specifically provided
herein.
This warranty covers only the equipment described by the Product Model Number and Unit Serial Number on the equipment or listed on the Warranty Registration Card, and applies only to products installed in the United States, Canada, or Puerto Rico. Tampering, altering, defacing, or removing the product serial number will serve to void this warranty. This warranty extends only to the original consumer purchaser and is nontransferable.
For this warranty to apply, the product must be installed according to Company recommendations and specifications, and in accordance with all
local, state, and national codes; and the product or residence must not be removed from its place of original installation. This warranty does not apply
to any unit sold over the Internet, by telephone or other electronic means unless the dealer that buys or sells a unit over the Internet, by telephone or
other electronic means also installs the unit. In the absence of a recorded Warranty Registration Card, the warranty period will begin upon product
shipment from Company. If you are unaware of the date the warranty became effective, contact Company at (877) 874-7378 or visit www.upgproductregistration.com.
ADDITIONAL CONDITIONS FOR HEAT EXCHANGER WARRANTY: This warranty shall cover the heat exchanger (primary and/or secondary, if
applicable) only if:
1. The product has not been operated with an input rate in excess of the rating plate attached to the product.
2. The product has not been allowed to operate without the use of the proper automatic limit control on the maximum warm air temperature
and/or without adequate circulation.
3. The product is installed so that the combustion air is not contaminated by compounds of chlorine, fluorine, or other damaging chemicals
(or vapors).
4. The product is installed such that the heat exchangers are not exposed to return air temperatures below stated ratings.
FOR PRODUCT REGISTRATION: For your benefit and protection, register your product with Company promptly after installation. This will initiate
the warranty period and allow us to contact you, should it become necessary. You can register your product online at www.upgproductregistration.com or by returning the Warranty Registration Card on the back page of this packet.
Product Model Number: ____________________________________
Installation Date: __________________________________________
Unit Serial Number: _______________________________________
Installing Dealer: __________________________________________
FOR WARRANTY SERVICE OR REPAIR: Consult the Authorized Service Center List packed with the unit installed in the manufactured home or
contact your installing or servicing dealer. The Authorized Service Center List is also available online at http://www.stylecrestinc.com/manufacturedhousing-products/hvac-service-documents/
Or, look in the Yellow Pages of the telephone book under Mobile Homes or Manufactured Housing Repair and Service for the name and telephone
number of the nearest authorized manufactured housing service center. If local authorized service cannot be obtained, or you are unable to contact
your installing dealer, contact the authorized distributor in your area. If you are unable to contact an authorized servicer, please contact StyleCrest
Inc., at 1-800-231-4822. If there is no distributor in your area, and you cannot obtain proper service under the terms of the warranty, please write:
Johnson Controls Unitary Products, Consumer Relations, 5005 York Drive, Norman, OK 73069.
WARRANTY PERIOD: The warranty period in years, depending on the part, is as shown in the chart below.
FURNACE MODELS
Furnace Model
DGAA, DGAH
Heat Exchanger
Parts Coverage
Labor and Trip Coverage*
10 years
2 years
1 year
NOTES:
*The warranty period for any replacement heat exchanger or part provided here under shall not extend beyond the warranty period stated above. The heat exchanger
warranty is on a parts only basis: no labor, freight or other service charges are allowed.
The warranty period will begin on the purchase date of the residence when the product is installed as original equipment, or the installation date when installed in a residence previously purchased by the consumer.
MAINTENANCE: Company strongly recommends regular periodic preventive maintenance on this equipment. The person most familiar with the
equipment in your HVAC system is a Participating Dealer. The Participating Dealer can ensure that your maintenance program meets the “Company
Warranty” conditions, maximize the equipment efficiency, and service your unit within the mandated guidelines with regard to unlawful discharge of
refrigerants into the atmosphere.
Johnson Controls Unitary Products
13
EXCLUSIONS: This warranty does not cover any:
1. Shipping, labor, or material charges or damages resulting from transportation, installation, or servicing.
2. Damage or repairs required as a consequence of mishandling, faulty installation, misapplication, abuse, improper servicing, unauthorized alteration, or improper operation.
3. Damages or failure to start resulting from improper voltage conditions, blown fuses, open circuit breakers, or other inadequacy or interruption of
electrical service or fuel supply.
4. Fuses, either internal or external to the product.
5. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing, or handling of either defective parts or replacement parts.
6. Products removed from their original location for reinstallation purposes.
7. Damages resulting from accident, abuse, fire, flood, alteration, or acts of God.
8. Damages resulting from use of the product in a corrosive atmosphere.
9. Normal maintenance, or damages resulting from failure to perform normal maintenance, as outlined in the installation and servicing instructions
or owner's manual.
10. Cleaning or replacement of filters, nozzles, or orifices.
11. Damages resulting from operation with inadequate supply of air or water; Damages resulting from failure to properly and regularly clean air and/
or water side of condenser and evaporator.
12. Damages resulting from: (I) freezing of condenser water or condensate; (II) inadequate or interrupted water supply; (III) use of corrosive water;
(IV) fouling or restriction of the water circuit by foreign material or like causes.
13. Damages caused by improper parts, components or accessories not suitable for use in or with the unit. For a list of parts that are known to be
compatible please reference the equipment renewal parts list, contact a Participating Dealer for assistance, or call 1-877-874-7378.
14. Electricity or fuel costs, or increases in fuel or electric costs, for any reason including additional or unusual use of supplemental electric heat.
This warranty is in lieu of all other express warranties. All implied warranties, including the implied warranty of merchantability and fitness for a particular purpose are limited in duration to the actual warranty period applicable to the part. Some states do not allow the disclaimer of implied warranties,
so the above disclaimer may not apply to you. In addition, some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. In no event, whether as a result of breach of warranty or contract, tort (including negligence), strict liability, or otherwise, shall Company be liable for special, incidental, or consequential damages or expenses, including but not limited to loss of use of the equipment
or associated equipment, lost revenues or profits, cost of substitute equipment, or cost of fuel or electricity.
The above limitations shall inure to the benefit of Company's suppliers and subcontractors. The above limitation on consequential damages shall not
apply to injuries to persons in the case of consumer goods. Company does not assume, or authorize any other person to assume for Company, any
other liability for the sale of this product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
Subject to change without notice. Published in U.S.A.
Copyright © 2013 by Johnson Controls, Inc. All rights reserved.
York International Corp.
3110 N. Mead
Wichita, KS 67219
129099-BUM-K-0613
Supersedes: 129099-BUM-J-0112
Download PDF