Cisco | 3524-PWR - Catalyst XL Enterprise Edition Switch | Installation guide | Cisco 3524-PWR - Catalyst XL Enterprise Edition Switch Installation guide

Catalyst 3500 Series XL
Hardware Installation Guide
May 2000
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Customer Order Number: DOC-786456=
Text Part Number: 78-6456-03
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT
NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT
ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR
THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION
PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO
LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate
radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television
reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in
part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class
A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct
any interference to radio or television communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco
equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by
using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television
or radio are on circuits controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as
part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE
PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL
DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR
INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Access Registrar, AccessPath, Any to Any, AtmDirector, Browse with Me, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, the Cisco
logo, Cisco Certified Internetwork Expert logo, CiscoLink, the Cisco Management Connection logo, the Cisco NetWorks logo, the Cisco Powered
Network logo, Cisco Systems Capital, the Cisco Systems Capital logo, Cisco Systems Networking Academy, the Cisco Systems Networking
Academy logo, the Cisco Technologies logo, ConnectWay, Fast Step, FireRunner, Follow Me Browsing, FormShare, GigaStack, IGX, Intelligence
in the Optical Core, Internet Quotient, IP/VC, Kernel Proxy, MGX, Natural Network Viewer, NetSonar, Network Registrar, the Networkers logo,
Packet, PIX, Point and Click Internetworking, Policy Builder, Precept, RateMUX, ScriptShare, Secure Script, ServiceWay, Shop with Me, SlideCast,
SMARTnet, SVX, The Cell, TrafficDirector, TransPath, ViewRunner, Virtual Loop Carrier System, Virtual Voice Line, VlanDirector, Voice LAN,
Wavelength Router, Workgroup Director, and Workgroup Stack are trademarks; Changing the Way We Work, Live, Play, and Learn, Empowering
the Internet Generation, The Internet Economy, and The New Internet Economy are service marks; and Aironet, ASIST, BPX, Catalyst, Cisco, Cisco
IOS, the Cisco IOS logo, Cisco Systems, the Cisco Systems logo, the Cisco Systems Cisco Press logo, Enterprise/Solver, EtherChannel, EtherSwitch,
FastHub, FastLink, FastPAD, FastSwitch, GeoTel, IOS, IP/TV, IPX, LightStream, LightSwitch, MICA, NetRanger, Post-Routing, Pre-Routing,
Registrar, StrataView Plus, Stratm, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. or its affiliates in the U.S. and certain
other countries. All other trademarks mentioned in this document are the property of their respective owners. The use of the word partner does not
imply a partnership relationship between Cisco and any of its resellers. (0004R)
Catalyst 3500 Series XL Hardware Installation Guide
Copyright © 2000, Cisco Systems, Inc.
All rights reserved.
C O N T E N T S
Preface ix
Audience ix
Purpose ix
Organization x
Conventions x
Related Publications xiv
Obtaining Documentation xiv
World Wide Web xiv
Documentation CD-ROM xiv
Ordering Documentation xv
Obtaining Technical Assistance xv
Cisco Connection Online xv
Technical Assistance Center xvi
Documentation Feedback xvii
CHAPTER
1
Product Overview 1-1
Features 1-1
Front-Panel Description 1-6
10/100 Ports 1-8
GBIC Module Slots 1-10
LEDs 1-12
System LED 1-15
RPS LED 1-16
Port LEDs and Modes 1-18
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
v
Contents
Rear-Panel Description 1-23
Power Connectors 1-25
Internal Power Supply Connector 1-25
Cisco RPS Connector 1-25
Console Port 1-26
Management Options 1-27
Network Configuration Examples 1-28
Design Concepts for Using the Switch 1-28
Small- to Medium-Sized Network Configuration 1-32
Collapsed Backbone and Switch Cluster Configuration 1-34
Large Campus Configuration 1-36
CHAPTER
2
Installing and Starting Up the Switch 2-1
Preparing for Installation 2-2
Warnings 2-2
EMC Regulatory Statements 2-4
U.S.A. 2-4
Taiwan 2-4
Installation Guidelines 2-5
Verifying Package Contents 2-6
Installing the Switch in a Rack 2-7
Removing Screws from the Switch 2-8
Attaching the Brackets to the Switch 2-9
Mounting the Switch in a Rack 2-11
Attaching the Optional Cable Guide 2-12
Installing the Switch on a Wall 2-13
Attaching the Brackets to the Switch 2-13
Attaching the Switch to a Wall 2-14
Catalyst 3500 Series XL Hardware Installation Guide
vi
78-6456-03
Contents
Installing the Switch on a Table or Shelf 2-15
Powering On the Switch and Running POST 2-15
Connecting to the 10/100 Ports 2-16
Connecting to the GBIC Module Ports 2-19
Connecting to a 1000BaseX GBIC Module Port 2-19
Connecting to a GigaStack GBIC Module Port 2-21
Connecting a PC or Terminal to the Console Port 2-22
Assigning Switch Information 2-24
Using the Setup Program 2-24
Using BOOTP 2-28
Default Configuration Settings 2-29
Where to Go Next 2-30
CHAPTER
3
Troubleshooting 3-1
Understanding POST Results 3-2
Diagnosing Problems 3-3
APPENDIX
A
Technical Specifications A-1
APPENDIX
B
Connector and Cable Specifications B-1
Connector Specifications B-1
10/100 Ports B-1
1000BaseX Ports B-2
Gigastack Port B-3
Console Port B-3
Cable and Adapter Specifications B-4
Crossover and Straight-Through Cable Pinouts B-4
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
vii
Contents
Rollover Cable and Adapter Pinouts B-5
Identifying a Rollover Cable B-5
Connecting to a PC B-6
Connecting to a Terminal B-7
APPENDIX
C
Translated Safety Warnings C-1
Attaching the Cisco RPS (model PWR600-AC-RPS) C-2
Attaching the Cisco RPS (model PWR300-AC-RPS) C-3
Service Personnel Warning C-4
Qualified Personnel Warning C-6
Installation Warning C-7
Jewelry Removal Warning C-8
Stacking the Chassis Warning C-10
Main Disconnecting Device C-12
Overtemperature Warning C-13
TN Power Warning C-15
Ground Connection Warning C-16
Circuit Breaker (15A) Warning C-17
Grounded Equipment Warning C-19
Supply Circuit Warning C-20
No On/Off Switch Warning C-21
Power Supply Warning C-22
Lightning Activity Warning C-25
Product Disposal Warning C-26
Chassis Warning—Rack-Mounting and Servicing C-27
INDEX
Catalyst 3500 Series XL Hardware Installation Guide
viii
78-6456-03
Preface
Audience
This guide is for the networking or computer technician responsible for installing
and configuring a Catalyst 3500 series XL switch. We assume that you are
familiar with the concepts and terminology of Ethernet and local area networking.
Purpose
The Catalyst 3500 Series XL Hardware Installation Guide documents the
hardware features of Catalyst 3500 series XL switches. It describes the physical
and performance characteristics of the switches in the series, explains how to
install a switch and set up its initial configuration, provides troubleshooting
information, and describes how to assign IP information to the switch.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
ix
Preface
Organization
Organization
This guide is organized into the following chapters:
Chapter 1, “Product Overview,” is a physical and functional overview of the
switch. It describes the switch ports, the standards they support, and the switch
LEDs. Examples of how the switch could be installed suggest possible
deployment strategies.
Chapter 2, “Installing and Starting Up the Switch,” contains the procedures for
installing a switch on a rack, wall, table, or shelf. It also describes how to set up
the switch initial configuration.
Chapter 3, “Troubleshooting,” describes how to identify and resolve some of the
problems that might arise when you are installing the switch.
Appendix A, “Technical Specifications,” lists the physical and environmental
specifications for the switches and the regulatory agency approvals.
Appendix B, “Connector and Cable Specifications,” describes the connectors,
cables, and adapters that can be used to connect to the switch.
Appendix C, “Translated Safety Warnings,” contains translations in various
languages of the warnings in this guide.
Conventions
This guide uses the following conventions to convey instructions and information:
Command descriptions use these conventions:
•
Commands and keywords are in boldface.
•
Arguments for which you supply values are in italic.
Examples use these conventions:
•
Terminal sessions and system displays are in screen font.
•
Information you enter is in boldface
•
Nonprinting characters, such as passwords or tabs, are in angle brackets (< >).
screen
font.
Catalyst 3500 Series XL Hardware Installation Guide
x
78-6456-03
Preface
Conventions
Notes, cautions, and warnings use the following conventions and symbols:
Note
Means reader take note. Notes contain helpful suggestions or
references to materials not contained in this manual.
Caution
Means reader be careful. In this situation, you might do something
that could result in equipment damage or loss of data.
Warning
This warning symbol means danger. You are in a situation that
could cause bodily injury. Before you work on any equipment, be
aware of the hazards involved with electrical circuitry and be
familiar with standard practices for preventing accidents. To see
translations of the warnings that appear in this publication, refer
to Appendix C, “Translated Safety Warnings.”
Waarschuwing
Dit waarschuwingssymbool betekent gevaar. U verkeert in een
situatie die lichamelijk letsel kan veroorzaken. Voordat u aan
enige apparatuur gaat werken, dient u zich bewust te zijn van de
bij elektrische schakelingen betrokken risico's en dient u op de
hoogte te zijn van standaard maatregelen om ongelukken te
voorkomen. Voor vertalingen van de waarschuwingen die in deze
publicatie verschijnen, kunt u het document Regulatory
Compliance and Safety Information (Informatie over naleving van
veiligheids- en andere voorschriften) raadplegen dat bij dit
toestel is ingesloten.
Varoitus
Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi
johtaa ruumiinvammaan. Ennen kuin työskentelet minkään
laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä
vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista.
Tässä julkaisussa esiintyvien varoitusten käännökset löydät
laitteen mukana olevasta Regulatory Compliance and Safety
Information -kirjasesta (määräysten noudattaminen ja tietoa
turvallisuudesta).
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
xi
Preface
Conventions
Attention
Ce symbole d'avertissement indique un danger. Vous vous trouvez
dans une situation pouvant causer des blessures ou des
dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers posés par les circuits électriques et
familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions
d’avertissements figurant dans cette publication, consultez le
document Regulatory Compliance and Safety Information
(Conformité aux règlements et consignes de sécurité) qui
accompagne cet appareil.
Warnung
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer
Situation, die zu einer Körperverletzung führen könnte. Bevor Sie
mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der
mit elektrischen Stromkreisen verbundenen Gefahren und der
Standardpraktiken zur Vermeidung von Unfällen bewußt.
Übersetzungen der in dieser Veröffentlichung enthaltenen
Warnhinweise finden Sie im Dokument Regulatory Compliance
and Safety Information (Informationen zu behördlichen
Vorschriften und Sicherheit), das zusammen mit diesem Gerät
geliefert wurde.
Avvertenza
Questo simbolo di avvertenza indica un pericolo. La situazione
potrebbe causare infortuni alle persone. Prima di lavorare su
qualsiasi apparecchiatura, occorre conoscere i pericoli relativi
ai circuiti elettrici ed essere al corrente delle pratiche standard
per la prevenzione di incidenti. La traduzione delle avvertenze
riportate in questa pubblicazione si trova nel documento
Regulatory Compliance and Safety Information (Conformità alle
norme e informazioni sulla sicurezza) che accompagna questo
dispositivo.
Advarsel
Dette varselsymbolet betyr fare. Du befinner deg i en situasjon
som kan føre til personskade. Før du utfører arbeid på utstyr, må
du vare oppmerksom på de faremomentene som elektriske kretser
innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder
å unngå ulykker. Hvis du vil se oversettelser av de advarslene som
finnes i denne publikasjonen, kan du se i dokumentet Regulatory
Compliance and Safety Information (Overholdelse av forskrifter og
sikkerhetsinformasjon) som ble levert med denne enheten.
Catalyst 3500 Series XL Hardware Installation Guide
xii
78-6456-03
Preface
Conventions
Aviso
Este símbolo de aviso indica perigo. Encontra-se numa situação
que lhe poderá causar danos físicos. Antes de começar a
trabalhar com qualquer equipamento, familiarize-se com os
perigos relacionados com circuitos eléctricos, e com quaisquer
práticas comuns que possam prevenir possíveis acidentes. Para
ver as traduções dos avisos que constam desta publicação,
consulte o documento Regulatory Compliance and Safety
Information (Informação de Segurança e Disposições
Reguladoras) que acompanha este dispositivo.
¡Advertencia!
Este símbolo de aviso significa peligro. Existe riesgo para su
integridad física. Antes de manipular cualquier equipo,
considerar los riesgos que entraña la corriente eléctrica y
familiarizarse con los procedimientos estándar de prevención de
accidentes. Para ver una traducción de las advertencias que
aparecen en esta publicación, consultar el documento titulado
Regulatory Compliance and Safety Information (Información sobre
seguridad y conformidad con las disposiciones reglamentarias)
que se acompaña con este dispositivo.
Varning!
Denna varningssymbol signalerar fara. Du befinner dig i en
situation som kan leda till personskada. Innan du utför arbete på
någon utrustning måste du vara medveten om farorna med
elkretsar och känna till vanligt förfarande för att förebygga
skador. Se förklaringar av de varningar som förkommer i denna
publikation i dokumentet Regulatory Compliance and Safety
Information (Efterrättelse av föreskrifter och
säkerhetsinformation), vilket medföljer denna anordning.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
xiii
Preface
Related Publications
Related Publications
For more information about Catalyst 3500 series XL switches and related
products, refer to the following publications:
•
Quick Start: Catalyst 3500 Series XL Cabling and Setup
•
Cisco IOS Desktop Switching Software Configuration Guide
•
Cisco IOS Desktop Switching Command Reference (online only)
•
Cisco Cluster Management Suite online help provides detailed procedures for
using a Web browser to change configuration settings and to display switch
information. Online help also provides detailed information about the fields
on each window.
•
Release Notes for the Catalyst 2900 Series XL and Catalyst 3500 Series XL
Cisco IOS Release 12.0(5)XU
•
Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide
•
Release Notes for the Catalyst GigaStack Gigabit Interface Converter
Obtaining Documentation
World Wide Web
You can access the most current Cisco documentation on the World Wide Web at
http://www.cisco.com, http://www-china.cisco.com, or
http://www-europe.cisco.com.
Documentation CD-ROM
Cisco documentation and additional literature are available in a CD-ROM
package, which ships with your product. The Documentation CD-ROM is updated
monthly. Therefore, it is probably more current than printed documentation. The
CD-ROM package is available as a single unit or as an annual subscription.
Catalyst 3500 Series XL Hardware Installation Guide
xiv
78-6456-03
Preface
Obtaining Technical Assistance
Ordering Documentation
Registered CCO users can order the Documentation CD-ROM and other Cisco
Product documentation through our online Subscription Services at
http://www.cisco.com/cgi-bin/subcat/kaojump.cgi.
Nonregistered CCO users can order documentation through a local account
representative by calling Cisco’s corporate headquarters (California, USA) at
408 526-4000 or, in North America, call 800 553-NETS (6387).
Obtaining Technical Assistance
Cisco provides Cisco Connection Online (CCO) as a starting point for all
technical assistance. Warranty or maintenance contract customers can use the
Technical Assistance Center. All customers can submit technical feedback on
Cisco documentation using the web, e-mail, a self-addressed stamped response
card included in many printed docs, or by sending mail to Cisco.
Cisco Connection Online
Cisco continues to revolutionize how business is done on the Internet. Cisco
Connection Online is the foundation of a suite of interactive, networked services
that provides immediate, open access to Cisco information and resources at
anytime, from anywhere in the world. This highly integrated Internet application
is a powerful, easy-to-use tool for doing business with Cisco.
CCO’s broad range of features and services helps customers and partners to
streamline business processes and improve productivity. Through CCO, you will
find information about Cisco and our networking solutions, services, and
programs. In addition, you can resolve technical issues with online support
services, download and test software packages, and order Cisco learning materials
and merchandise. Valuable online skill assessment, training, and certification
programs are also available.
Customers and partners can self-register on CCO to obtain additional
personalized information and services. Registered users may order products,
check on the status of an order and view benefits specific to their relationships
with Cisco.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
xv
Preface
Obtaining Technical Assistance
You can access CCO in the following ways:
•
WWW: www.cisco.com
•
Telnet: cco.cisco.com
•
Modem using standard connection rates and the following terminal settings:
VT100 emulation; 8 data bits; no parity; and 1 stop bit.
– From North America, call 408 526-8070
– From Europe, call 33 1 64 46 40 82
You can e-mail questions about using CCO to cco-team@cisco.com.
Technical Assistance Center
The Cisco Technical Assistance Center (TAC) is available to warranty or
maintenance contract customers who need technical assistance with a Cisco
product that is under warranty or covered by a maintenance contract.
To display the TAC web site that includes links to technical support information
and software upgrades and for requesting TAC support, use
www.cisco.com/techsupport.
To contact by e-mail, use one of the following:
Language
E-mail Address
English
tac@cisco.com
Hanzi (Chinese)
chinese-tac@cisco.com
Kanji (Japanese)
japan-tac@cisco.com
Hangul (Korean)
korea-tac@cisco.com
Spanish
tac@cisco.com
Thai
thai-tac@cisco.com
In North America, TAC can be reached at 800 553-2447 or 408 526-7209. For
other telephone numbers and TAC e-mail addresses worldwide, consult the
following web site:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
Catalyst 3500 Series XL Hardware Installation Guide
xvi
78-6456-03
Preface
Obtaining Technical Assistance
Documentation Feedback
If you are reading Cisco product documentation on the World Wide Web, you can
submit technical comments electronically. Click Feedback in the toolbar and
select Documentation. After you complete the form, click Submit to send it to
Cisco.
You can e-mail your comments to bug-doc@cisco.com.
To submit your comments by mail, for your convenience many documents contain
a response card behind the front cover. Otherwise, you can mail your comments
to the following address:
Cisco Systems, Inc.
Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate and value your comments.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
xvii
Preface
Obtaining Technical Assistance
Catalyst 3500 Series XL Hardware Installation Guide
xviii
78-6456-03
C H A P T E R
1
Product Overview
This chapter provides the following topics that describe the
Catalyst 3500 series XL switches:
•
Switch features
•
Descriptions of the front and rear panels
•
Management options
•
Examples of the Catalyst 3500 XL switches in different network topologies
Features
The Catalyst 3500 series XL switches—also referred to as Catalyst 3500 XL
switches—are stackable 10/100 Ethernet switches to which you can connect
workstations and Cisco IP Phones and other network devices such as servers,
routers, and other switches. These switches also can be deployed as backbone
switches, aggregating 10/100 and Gigabit Ethernet traffic from other network
devices. A feature specific to the Catalyst 3524-PWR XL switch is its ability to
provide inline power to Cisco IP Phones. (Phone adapters are not required when
connecting to the Catalyst 3524-PWR XL 10/100 switch ports.)
Figure 1-1 shows the switch models in the series, and Table 1-1 and Table 1-2 list
their features.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-1
Chapter 1
Product Overview
Features
Figure 1-1
Catalyst 3500 Series XL Switches
Switch
Description
WS-C3508G-XL
8 GBIC1-based gigabit
module slots
1
2
SYSTEM
3
RPS
4
5
6
STATUS
MODE
7
UTIL
8
DUPLX
SPEED
12 autosensing10/100
Ethernet ports
1
WS-C3524-XL
4
5
6
7
8
9
10
11 12
11X
RPS
1
UTIL
2
2X
DUPLX
12X
SPEED
24 autosensing 10/100
Ethernet ports
1
2
3
4
5
6
7
8
9
10
11 12
13 14
1X
11X
13X
12X
14X
15 16
17 18
19 20
21 22
23 24
23X
SYSTEM
RPS
MODE
1
STATUS
UTIL
2
2X
DUPLX
SPEED
24X
24 autosensing 10/100
inline-power Ethernet ports
2 GBIC-based gigabit
module slots
WS-C3548-XL
3
SYSTEM
STATUS
MODE
2 fixed GBIC-based gigabit
module slots
WS-C3524-PWR-XL
2
1X
2 GBIC-based gigabit
module slots
1
2
3
4
5
6
7
8
9
10
11 12
13 14
1X
11X
15 16
17 18
19 20
21 22
23 24
13X
23X
SYSTEM
RPS
MODE
1
2X
STATUS
2
12X
DUPLX
14X
SPEED
24X
LINE PWR
48 autosensing 10/100
Ethernet ports
2 GBIC-based gigabit
module slots
1
1X
2
3
4
5
6
7
8
9
10
11 12
13 14
15 16
17 18
15X
17X
16X
18X
SYSTEM
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
31X
33X
32X
34X
RPS
35 36
37 38
39 40
41 42
43 44
45 46
47 48
47X
STATUS
1
UTIL
DUPLEX
SPEED
2X
MODE
48X
2
30210
WS-C3512-XL
1. GBIC = Gigabit Interface Converter
Catalyst 3500 Series XL Hardware Installation Guide
1-2
78-6456-03
Chapter 1
Product Overview
Features
Table 1-1
Catalyst 3508G XL Features
Feature
Description
Performance and
Configuration
•
8 GBIC-based 1000BaseX Gigabit Ethernet slots
•
Support for up to 250 port-based virtual LANs (VLANs)
•
Inter-Switch Link (ISL) and IEEE 802.1Q trunking support on all ports
•
IEEE 802.1p capable
•
High-speed EtherChannel connections between switches and servers
•
8192 MAC addresses
•
Cisco Group Management Protocol (CGMP) to limit the flooding of IP
multicast traffic
•
Broadcast storm control to prevent performance degradation from broadcast
storms
•
Switch Port Analyzer (SPAN) port monitoring on any port
•
Support for command switch redundancy
•
Support for Cisco Gigabit Interface Converter (GBIC) modules
– GigaStack GBIC module
– 1000BaseSX GBIC module
– 1000BaseLX/LH GBIC module
– 1000BaseZX GBIC module (support for up to four 1000BaseZX GBICs
with the Catalyst 3508G XL switch)
Management
Power
Redundancy
•
Cisco IOS command-line interface (CLI) through the console port or Telnet
•
CiscoView device-management application
•
Cluster Management Suite, a web-based tool for managing switch clusters or
an individual switch through a single IP address
•
Simple Network Management Protocol (SNMP)
•
Connection for optional Cisco 600W Redundant Power System (RPS) that
operates on AC input and supplies DC output to the switch
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-3
Chapter 1
Product Overview
Features
Table 1-2
Catalyst 3512, 3524, 3524-PWR, and 3548 XL Features
Feature
Description
Performance and
Configuration
•
Autonegotiation of speed and duplex operation on 10/100 Ethernet ports
•
12, 24, or 48 10/100 Ethernet ports and 2 GBIC-based Gigabit Ethernet
slots
•
Support for up to 250 port-based VLANs
•
ISL and IEEE 802.1Q trunking support on all ports
•
Support for voice VLAN ID (VVID)
•
High-speed EtherChannel connections between switches and servers
•
8192 MAC addresses
•
IEEE 802.1p capable
•
CGMP to limit the flooding of IP multicast traffic
•
Broadcast storm control to prevent performance degradation from
broadcast storms
•
SPAN port monitoring on any port
•
Support for command switch redundancy
•
Support for Cisco GBIC modules
– GigaStack GBIC
– 1000BaseSX GBIC module
– 1000BaseLX/LH GBIC module
– 1000BaseZX GBIC module
Catalyst 3500 Series XL Hardware Installation Guide
1-4
78-6456-03
Chapter 1
Product Overview
Features
Table 1-2
Catalyst 3512, 3524, 3524-PWR, and 3548 XL Features (continued)
Feature
Management
Power Redundancy
Inline Power
(Catalyst 3524-PWR
XL switch only)
Description (continued)
•
Cisco IOS CLI through the console port or Telnet
•
CiscoView device-management application
•
Cluster Management Suite, a web-based tool for managing switch clusters
or an individual switch through a single IP address
•
SNMP
•
Connection for optional Cisco RPS 600 that operates on AC input and
supplies DC output to the Catalyst 3512, 3524, and 3548 XL switches
•
Connection for optional Cisco RPS 300 that operates on AC input and
supplies DC output to the Catalyst 3524-PWR XL switch
•
Ability to provide inline power for Cisco IP Phones from all 24 10/100
Ethernet ports
•
Auto-detection and control of inline phone power on a per-port basis on all
10/100 ports
•
Support for fan-fault and over-temperature detection through Visual Switch
Manager (VSM)
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-5
Chapter 1
Product Overview
Front-Panel Description
Front-Panel Description
The front panel of the Catalyst 3508G XL switch (Figure 1-2) has eight
1000BaseX GBIC module slots but no 10/100 ports. The front panel of the
Catalyst 3512, 3524, 3524-PWR and 3548 XL switches (Figure 1-3, Figure 1-4,
Figure 1-5, and Figure 1-6) have 10/100 RJ-45 ports and two 1000BaseX GBIC
module slots. All Catalyst 3500 XL switches have a set of LEDs and a Mode
button. (The Catalyst 3548 XL switch has a Mode label that you press.) These
front-panel components are described in this section.
Catalyst 3508G XL Switch
18966
Figure 1-2
1
2
SYSTEM
3
RPS
MODE
4
5
6
STATUS
7
UTIL
8
DUPLX
SPEED
GBIC module slots
Catalyst 3512 XL Switch
26235
Figure 1-3
1
2
3
4
5
6
7
8
9
10
11 12
1X
11X
SYSTEM
RPS
MODE
STATUS
1
2X
2
12X
UTIL
DUPLX
SPEED
10/100 ports
GBIC module slots
Catalyst 3500 Series XL Hardware Installation Guide
1-6
78-6456-03
Chapter 1
Product Overview
Front-Panel Description
Catalyst 3524 XL Switch
26237
Figure 1-4
1
2
3
4
5
6
7
8
9
10
11 12
13 14
1X
11X
15 16
17 18
19 20
21 22
23 24
13X
23X
SYSTEM
RPS
MODE
1
2X
STATUS
2
12X
UTIL
14X
DUPLX
24X
SPEED
10/100 ports
Catalyst 3524-PWR XL Switch
30291
Figure 1-5
GBIC module slots
1
2
3
4
5
6
7
8
9
10
11 12
13 14
1X
11X
15 16
17 18
19 20
21 22
23 24
13X
23X
SYSTEM
RPS
MODE
1
2X
STATUS
2
12X
DUPLX
14X
SPEED
24X
LINE PWR
10/100 inline-power ports
Catalyst 3548 XL Switch
28010
Figure 1-6
GBIC module slots
1
2
3
4
1X
5
6
7
8
9
10
11 12
13 14
15 16
17 18
15X
17X
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
SYSTEM
RPS
31X
33X
32X
34X
35 36
37 38
39 40
41 42
43 44
45 46
47 48
47X
STATUS
UTIL
1
DUPLX
SPEED
2X
MODE
16X
18X
2
48X
10/100 ports
GBIC
module slots
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-7
Chapter 1
Product Overview
Front-Panel Description
10/100 Ports
The 10/100 ports on the Catalyst 3512, 3524, 3524-PWR, and 3548 XL switches
are grouped in pairs. For example, in Figure 1-3, Figure 1-4, Figure 1-5, and
Figure 1-6, ports 1 and 2 are the left-most pair. The first member of the pair
(port 1) is above the second member (port 2). Port 3 is above port 4, and so on.
The 10/100 switch ports can connect, up to a distance of 100 meters, to any
compatible network device:
Note
•
10BaseT-compatible devices such as workstations, Cisco IP Phones, and hubs
through standard RJ-45 connectors and Category 3, 4, or 5 cabling
•
100BaseTX-compatible devices such as high-speed workstations, Cisco IP
Phones, servers, hubs, routers, and other switches through standard RJ-45
connectors and Category 5 cabling
Category 5 cable is required for 100BaseTX traffic. Ports operating
at 10 Mbps can use Category 3 and 4 cables, but these cables do not
work for ports operating at 100 Mbps.
When connecting the switch to workstations, servers, routers, and
Cisco IP Phones, be sure that the cable is a straight-through,
twisted-pair cable. When connecting the switch to switches or hubs,
use a crossover cable. Pinouts for the cables are described in
Appendix B, “Connector and Cable Specifications.”
The 10/100 switch ports can be explicitly set to operate in any combination of
half duplex, full duplex, 10 Mbps, or 100 Mbps. These ports also can be set for
speed and duplex autonegotiation, compliant with IEEE 802.3u. When set for
autonegotiation, the port can sense the speed and duplex settings of the attached
device and advertises its own capabilities. If the connected device also supports
autonegotiation, the switch port negotiates the best connection (that is, the fastest
line speed that both devices support and full-duplex transmission, if the attached
device supports it) and configures itself accordingly.
Catalyst 3500 Series XL Hardware Installation Guide
1-8
78-6456-03
Chapter 1
Product Overview
Front-Panel Description
The 10/100 ports on the Catalyst 3512, 3524, 3524-PWR, and 3548 XL switches
provide protocol support for Cisco IP Phones. The Catalyst 3548 and
3524-PWR XL switches also support per-port priority override. Refer to the Cisco
IOS Desktop Switching Software Configuration Guide for more information about
these features.
Cisco IP Phones—connected to the 10/100 ports on the Catalyst 3512, 3524, and
3548 XL switches—must be connected to an AC power source. However, the
Catalyst 3524-PWR XL 10/100 ports can:
•
Provide –48V DC power to the following phones: Cisco IP Phone 7960,
Cisco IP Phone 7940, and Cisco IP Phone 7910
•
Automatically detect if a Cisco IP Phone is connected
On a per-port basis, you can control whether or not a Catalyst 3524-PWR XL
10/100 port automatically provides power when a Cisco IP Phone is connected.
CMS and the CLI provide two inline power settings for each 10/100 port: Auto
and Never. When you select the Auto setting for inline power on a port, the port
only provides power if a Cisco IP Phone is connected to it. The Auto setting is the
default. However, when you select the Never setting for inline power on a port,
the port does not provide power even if a Cisco IP Phone is connected to it.
You also can connect the Cisco IP Phone to a Catalyst 3524-PWR XL 10/100 port
and to an AC power source for redundant power. The power source to which the
Cisco IP Phone is first connected becomes its primary power source, and the
second power source is its backup. If the primary source fails, the second power
source becomes the primary power source to the Cisco IP Phone. During the
power transfer, the phone might reboot or reestablish link with the switch.
For information about Cisco IP Phones, refer to the documentation that came with
your Cisco IP Phone.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-9
Chapter 1
Product Overview
Front-Panel Description
GBIC Module Slots
The Cisco Gigabit Interface Converter (GBIC) module slots support the following
modules to provide flexibility in media and distance options:
•
1000BaseSX GBIC module for fiber connections of up to 550 meters.
•
1000BaseLX/LH GBIC module for fiber connections of up to 10 kilometers.
•
1000BaseZX GBIC module for fiber connections of up to 100 kilometers.
•
GigaStack GBIC module for creating a 1-Gbps stack configuration of up to
nine Catalyst 3500 XL switches. The GigaStack GBIC supports one
full-duplex link (in a point-to-point configuration) or up to nine half-duplex
links (in a stack configuration) to other Gigabit Ethernet devices. Using the
required Cisco proprietary signaling and cabling, the maximum distance for
a GigaStack GBIC-to-GigaStack GBIC connection is 1 meter.
You can install up to two GBICs in the Catalyst 3512, 3524, 3524-PWR and
3548 XL switches and up to eight GBICs in the Catalyst 3508G XL switch.
Note
GBIC modules are not factory-installed on these switches, but you
can order GBIC modules separately.
Figure 1-7 and Figure 1-8 show how a GBIC module is inserted into a GBIC
module slot on the switch. Refer to the documentation that came with your GBIC
module for complete GBIC module information.
Catalyst 3500 Series XL Hardware Installation Guide
1-10
78-6456-03
Chapter 1
Product Overview
Front-Panel Description
Figure 1-7
Installing a 1000BaseX GBIC Module in the Switch
Metal flap door
1
2
SYSTEM
RPS
3
18965
MODE
STATUS
UTIL
DUPLX
SPEED
GBIC module slot
1000BaseX GBIC module
Figure 1-8
Installing a GigaStack GBIC Module in the Switch
Metal flap door
1
2
SYSTEM
RPS
STATUS
UTIL
DUPLX
SPEED
3
22081
MODE
GBIC module slot
1
2
GigaStack GBIC
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-11
Chapter 1
Product Overview
Front-Panel Description
LEDs
You can use the switch LEDs described in this section to monitor switch activity
and its performance. Figure 1-9, Figure 1-10, Figure 1-11, and Figure 1-12 show
the location of the LEDs and the Mode button that you use to select one of the port
modes.
All of the LEDs described in this section except the utilization meter (UTL) are
visible on the VSM home page and Cluster Manager page. The Cisco IOS Desktop
Switching Software Configuration Guide describes how to use the Cluster
Management Suite to monitor individual switches and how to use cluster
management software to monitor all the switches in a cluster.
Figure 1-9
Catalyst 3508G XL LEDs
GBIC module slot LEDs
1
2
SYSTEM
RPS
STATUS
UTIL
DUPLX
SPEED
3
18961
MODE
System LED
Mode button
Redundant power system LED
Status LED
Utilization LED
Duplex LED
Speed LED
Catalyst 3500 Series XL Hardware Installation Guide
1-12
78-6456-03
Chapter 1
Product Overview
Front-Panel Description
Figure 1-10 Catalyst 3512 and 3524 XL LEDs
Port LEDs
1
2
3
4
5
6
7
8
9
10
1X
11 12
11X
SYSTEM
RPS
STATUS
UTIL
DUPLX
SPEED
2X
12X
22028
MODE
System LED
Mode button
Redundant power system LED
Status LED
Utilization LED
Duplex LED
Speed LED
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-13
Chapter 1
Product Overview
Front-Panel Description
Figure 1-11 Catalyst 3524-PWR XL LEDs
Port LEDs
1
2
3
4
5
6
7
8
9
10
1X
11 12
11X
SYSTEM
RPS
STATUS
DUPLX
SPEED
LINE PWR
2X
12X
30292
MODE
System LED
Mode button
Redundant power system LED
Status LED
Duplex LED
Speed LED
Line power LED
Catalyst 3500 Series XL Hardware Installation Guide
1-14
78-6456-03
Chapter 1
Product Overview
Front-Panel Description
Figure 1-12 Catalyst 3548 XL LEDs
Port LEDs
1
2
3
4
5
6
1X
7
8
9
10
11 12
13 14
15 16
15X
SYSTEM
RPS
STATUS
UTIL
DUPLX
2X
16X
MODE
System LED
Mode label
28325
SPEED
Redundant power system LED
Status LED
Utilization LED
Duplex LED
Speed LED
System LED
The System LED shows whether the system is receiving power and is functioning
properly. Table 1-3 lists the LED colors and their meanings.
Table 1-3
System LED
Color
System Status
Off
System is not powered on.
Green
System is operating normally.
Amber
System is receiving power but is not functioning properly.
For information on the System LED colors during POST, see the “Powering On
the Switch and Running POST” section on page 2-15.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-15
Chapter 1
Product Overview
Front-Panel Description
RPS LED
The Redundant Power System (RPS) LED shows the RPS status. Table 1-4 and
Table 1-5 list the LED colors and their meanings.
Note
Table 1-4
The Cisco RPS 600 (model PWR600-AC-RPS) supports the
Catalyst 3512, 3524, 3548, and 3508 XL switches.
RPS LED for the Catalyst 3508, 3512, 3524, and 3548 XL Switches
Color
RPS Status
Off
RPS is off or is not installed.
Solid green
RPS is operational.
Blinking green
RPS and the switch AC power supply are both powered on. If the switch power
supply fails, the switch powers down and restarts after 15 seconds, using power
from the RPS. The switch goes through its normal boot sequence when it restarts.
Note
Amber
This is not a recommended configuration. For more
information see the “RPS Connector on the Catalyst 3508,
3512, 3524, and 3548 XL Switches” section on page 1-25.
RPS is connected but not functioning properly. One of the power supplies in the
RPS could be powered down, or a fan on the RPS could have failed.
Note
If you are using an RPS with a revision level lower than Z3
with a Catalyst 3508G XL or a Catalyst 3548 XL switch, the
switch RPS LED might display amber (normally indicating an
RPS malfunction) even when the RPS is functioning properly.
The LEDs display correctly for RPS revision level Z3 or later.
The label on the bottom of the RPS shows the revision level.
Catalyst 3500 Series XL Hardware Installation Guide
1-16
78-6456-03
Chapter 1
Product Overview
Front-Panel Description
Note
Table 1-5
The Cisco RPS 300 (model PWR300-AC-RPS) supports the
Catalyst 3524-PWR XL switch.
RPS LED for the Catalyst 3524-PWR XL Switch
Color
RPS Status
Off
RPS is off or is not installed.
Solid green
RPS is connected and operational.
Blinking green
RPS is backing up another switch in the stack.
Solid amber
RPS is connected but not functioning properly. One of the power supplies in the
RPS could be powered down, or a fan on the RPS could have failed.
Blinking amber
Internal power supply of the switch is down, and redundancy is lost. The switch is
operating on the RPS.
For more information about the failure conditions on the Cisco RPS 300, refer to
the Cisco Redundant Power System 300 Hardware Installation Guide.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-17
Chapter 1
Product Overview
Front-Panel Description
Port LEDs and Modes
Each 10/100 port and module slot has a port LED. These port LEDs, as a group
or individually, display information about the switch and about the individual
ports. The port modes (Table 1-6) determine the type of information displayed
through the port LEDs.
To select or change a mode, press the Mode button until the desired mode is
highlighted. When you change port modes, the meaning of the port LED colors
also changes. Table 1-7 and Table 1-8 explain how to interpret the port LED
colors after you change the port mode.
Note
Table 1-6
To change the port mode in the Catalyst 3548 XL switch, press the
Mode label.
Port Mode LEDs
Mode LED
Port Mode
Description
STAT
Port status
The port status. This is the default mode.
UTL
Switch utilization
The current bandwidth in use by the switch.
DUPLX
Port duplex mode
The port duplex mode: full duplex or half duplex.
SPEED
Port speed
The port operating speed: 10, 100, or 1000 Mbps.
LINE PWR
Port inline power
The inline power status: on or off.
Catalyst 3500 Series XL Hardware Installation Guide
1-18
78-6456-03
Chapter 1
Product Overview
Front-Panel Description
Table 1-7
Meaning of LED Colors in Different Modes on the Catalyst 3508, 3512, 3524, and
3548 XL Switches
Port Mode
LED Color
Meaning
STATUS
(port status)
Off
No link.
Solid green
Link present.
Flashing green
Activity. Port is transmitting or receiving data.
Alternating
green-amber
Link fault. Error frames can affect connectivity, and errors such as
excessive collisions, CRC errors, and alignment and jabber errors
are monitored for a link-fault indication.
Solid amber
Port is not forwarding. Port was disabled by management or an
address violation or was blocked by Spanning Tree Protocol (STP).
Note
UTL
(utilization)
Green
After a port is reconfigured, the port LED can remain
amber for up to 30 seconds as STP checks the switch for
possible loops.
The LEDs display backplane utilization on a logarithmic scale.
If all port LEDs are green, the switch is using 50 percent or more
of its total bandwidth capacity. If the right-most LED is amber, the
switch is using less than 50 percent of its total bandwidth. If the
LED to the left of the right-most LED is amber, the switch is using
less than 25 percent of its total capacity, and so on.
See Figure 1-13, Figure 1-15, and Figure 1-16 for details.
DUPLEX
SPEED
(speed)
Off
Port is operating in half duplex.
Green
Port is operating in full duplex.
10/100 ports
Off
Port is operating at 10 Mbps.
Green
Port is operating at 100 Mbps.
1000BaseX ports
Off
Port is not operating.
Green
Port is operating at 1000 Mbps.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-19
Chapter 1
Product Overview
Front-Panel Description
Table 1-8
Meaning of LED Colors in Different Modes on the Catalyst 3524-PWR XL Switch
Port Mode
LED Color
Meaning
STATUS
(port status)
Off
No link.
Solid green
Link present.
Flashing green
Activity. Port is transmitting or receiving data.
Alternating
green-amber
Link fault. Error frames can affect connectivity, and errors such as
excessive collisions, CRC errors, and alignment and jabber errors
are monitored for a link-fault indication.
Solid amber
Port is not forwarding. Port was disabled by management or an
address violation or was blocked by Spanning Tree Protocol (STP).
Note
DUPLEX
SPEED
(speed)
After a port is reconfigured, the port LED can remain
amber for up to 30 seconds as STP checks the switch for
possible loops.
Off
Port is operating in half duplex.
Green
Port is operating in full duplex.
10/100 ports
Off
Port is operating at 10 Mbps.
Green
Port is operating at 100 Mbps.
1000BaseX ports
Off
Port is not operating.
Green
Port is operating at 1000 Mbps.
LINE PWR
Off
(inline power) Green
Inline power is off.
Inline power is on.
If the Cisco IP Phone is receiving power from an AC power source,
the port LED is off even if the IP phone is connected to the switch
port. The LED turns green only when the switch port is providing
power.
Catalyst 3500 Series XL Hardware Installation Guide
1-20
78-6456-03
Chapter 1
Product Overview
Front-Panel Description
Figure 1-13, Figure 1-14, Figure 1-15, and Figure 1-16 show the bandwidth
utilization percentages displayed by the right-most LEDs.
Note
The port LEDs on the Catalyst 3524-PWR XL switch do not show
bandwidth utilization. To find out the switch bandwidth usage, use
the Device Bandwidth Graph on VSM.
Figure 1-13 Bandwidth Utilization for the Catalyst 3508G XL Switch
Catalyst 3500
4
5
7
6
XL
22006
3
2
1
8
SYSTEM
RPS
MODE
STATUS
UTIL
DUPLX
SPEED
< 25%
25% – 49% +
50% +
Figure 1-14 Bandwidth Utilization for the Catalyst 3512 XL Switch
2
3
4
5
6
7
8
9
10
XL
Catalyst 3500
11 12
11X
1
2
RPS
MODE
STATUS
UTIL
2X
12X
DUPLX
SPEED
38399
1
1X
SYSTEM
< 25% +
25% – 49% +
50% +
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-21
Chapter 1
Product Overview
Front-Panel Description
Figure 1-15 Bandwidth Utilization for the Catalyst 3524 XL Switch
2
3
4
5
6
7
8
9
10
11 12
13 14
11X
15 16
17 18
19 20
21 22
XL
Catalyst 3500
23 24
13X
15X
1
22007
1
1X
2
SYSTEM
RPS
MODE
STATUS
UTIL
2X
12X
14X
16X
DUPLX
SPEED
< 25% +
25% – 49% +
50% +
Figure 1-16 Bandwidth Utilization for the Catalyst 3548 XL Switch
Catalyst 3500
1
1X
2
3
24
5
6
7
8
9
10
11 12
13 14
15 16
17 18
15X
19 20
21 22
23 24
25 26
27 28
29 31
31 32
17X
33 34
31X
33X
35 36
37 38
39 40
41 42
43 44
45 46
XL
47 48
47X
RPS
STATUS
UTIL
2
DUPLX
SPEED
2X
16X
32X
18X
MODE
34X
48X
28366
1
SYSTEM
< 25% +
25% – 49% +
50% +
If all port LEDs on the Catalyst 3548 XL switch are green, the switch is using
50 percent or more of its total bandwidth capacity. If all 10/100 port LEDs are
green and the lower GBIC LED is amber, the switch is using between 25 and
50 percent of its total bandwidth. If all 10/100 port LEDs are green and if both the
GBIC LEDs are amber, the switch is using less than 25 percent of its total
capacity, and so on.
Catalyst 3500 Series XL Hardware Installation Guide
1-22
78-6456-03
Chapter 1
Product Overview
Rear-Panel Description
Rear-Panel Description
Switch rear panels have an AC power connector, an RPS connector, and an RJ-45
console port (see Figure 1-17, Figure 1-19, Figure 1-18, and Figure 1-20), which
are described in this section.
18963
Figure 1-17 Catalyst 3508G XL Rear Panel
RATING
100-127/200-240V~
1.0A/0.5A 50-60HZ
DC INPUTS FOR REMOTE POWER
SUPPLY
SPECIFIED IN MANUAL. +3.3V***@1
4A,
+12V***@3A
DC INPUT
CONSOLE
Fans
AC power
connector
RJ-45
console port
Redundant
power system
connector
18964
Figure 1-18 Catalyst 3512 and 3524 XL Rear Panel
RATING
100-127/200-240V~
1.0A/0.5A 50-60HZ
AC power
connector
CONSOLE
DC INPUTS FOR REMOTE
POWER SUPPLY
SPECIFIED IN MANUAL.
+5V @24A, +12V @.5A
Fans
RJ-45
console port
Redundant
power system
connector
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-23
Chapter 1
Product Overview
Rear-Panel Description
30293
Figure 1-19 Catalyst 3524-PWR XL Rear Panel
DC INPUTS FOR REMOTE
POWER SUPPLY
SPECIFIED IN MANUAL.
-48V @3A, +12V @6A
RATING
100-127/200-240V~
3.5A/1.8A 50-60HZ
CONSOLE
Fans
AC power
connector
Redundant
power system
connector
RJ-45
console port
28012
Figure 1-20 Catalyst 3548 XL Rear Panel
DC INPUTS FOR REMOTE
POWER SUPPLY
SPECIFIED IN MANUAL
+3.3V @17A, +12 @1.1A
RATING
100-127/200-240V~
1.6A/0.9A 50-60HZ
AC power
connector
Fan
exhaust
CONSOLE
RJ-45
console port
Redundant
power system
connector
Catalyst 3500 Series XL Hardware Installation Guide
1-24
78-6456-03
Chapter 1
Product Overview
Rear-Panel Description
Power Connectors
You can provide power to the switch either through the internal power supply or
through the Cisco RPS.
Internal Power Supply Connector
The internal power supply is an autoranging unit that supports input voltages
between 100 and 240 VAC. If you plan to use the internal power supply, use the
supplied AC power cord to connect the AC power connector to an AC power
outlet.
Cisco RPS Connector
Specific Cisco RPS models support specific Catalyst 3500 XL switches:
•
Cisco RPS 600 (model PWR600-AC-RPS)—Supports the Catalyst 3512,
3524, 3548, and 3508 XL switches
•
Cisco RPS 300 (model PWR300-AC-RPS)—Supports the
Catalyst 3524-PWR XL switch
RPS Connector on the Catalyst 3508, 3512, 3524, and 3548 XL Switches
The Cisco RPS 600 (model PWR600-AC-RPS) provides a quasi-redundant power
source for four external devices that use up to 150W DC each. Use a one-to-one
cable (one connector at each cable end) to connect four external devices to the
four DC output power modules. The power source is quasi-redundant because
there are two AC input power modules for the Cisco RPS and one DC output
power module for each external device. The AC input to the Cisco RPS is fully
redundant, but the DC output to the external devices is not.
Warning
Note
Attach only the Cisco RPS (model PWR600-AC-RPS) to the RPS
receptacle.
Do not connect the switch power cord to an AC outlet if the switch
is also connected to a powered-on RPS. The switches do not support
the fully-redundant configuration described in the RPS
documentation. The redundant-with-reboot configuration is not
recommended. For more information on the Cisco RPS 600, refer to
the Cisco Redundant Power System Hardware Installation Guide.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-25
Chapter 1
Product Overview
Rear-Panel Description
RPS Connector on the Catalyst 3524-PWR XL Switch
The Cisco RPS 300 (model PWR300-AC-RPS) has two output levels: –48V and
12V with a total output power of 300W. It provides a fully-redundant power
source for up to six switches. It automatically senses when one of the switches has
experienced power failure and automatically sends power to the affected switch.
Although it supports up to six switches, it can power only one switch at a time. If
more than one switch fails at the same time, the subsequent switches will not be
powered.
Warning
Attach only the Cisco RPS (model PWR300-AC-RPS) to the RPS
receptacle.
For more information on the Cisco RPS 300, refer to the Cisco Redundant Power
System 300 Hardware Installation Guide.
Console Port
You can connect a Catalyst 3500 XL switch to a PC by means of the console port
and the supplied rollover cable and DB-9 adapter. You need to provide a
RJ-45-to-DB-25 female DTE adapter if you want to connect the switch console
port to a terminal. You can order a kit (part number ACS-DSBUASYN=)
containing that adapter from Cisco. For console port and adapter pinout
information, see the “Cable and Adapter Specifications” section on page B-4.
Catalyst 3500 Series XL Hardware Installation Guide
1-26
78-6456-03
Chapter 1
Product Overview
Management Options
Management Options
Catalyst 3500 XL switches offer several management options:
•
Cisco Cluster Management Suite
This suite is made up of four web-based applications that you use to create,
monitor, and configure a cluster of switches or an individual switch. You use
the Cluster Builder, Cluster View, and Cluster Manager applications to create,
configure, and monitor clusters. You use the Visual Switch Manager (VSM)
application to manage individual and standalone switches. For more
information, refer to the Cisco IOS Desktop Switching Software
Configuration Guide and the online help for these applications.
•
Cisco IOS command-line interface (CLI)
Connect a PC or terminal directly to the console port, located on the rear
panel of the switch, to access the CLI. If the switch is connected to your
network, you can use a Telnet connection to manage the switch from a remote
location. See the Cisco IOS Desktop Switching Command Reference for more
information.
•
CiscoView application
The CiscoView device-management application displays the switch image
that you can use to set configuration parameters and to view switch status and
performance information. The CiscoView application, which you purchase
separately, can be a standalone application or part of an SNMP
network-management platform. See the CiscoView documentation for more
information.
•
Simple Network Management Protocol (SNMP) network management
You can manage switches from an SNMP-compatible management station
that is running platforms such as HP OpenView or SunNet Manager. The
switch supports a comprehensive set of MIB extensions and MIB II, the
IEEE 802.1D bridge MIB, and four Remote Monitoring (RMON) groups. See
the documentation that came with your SNMP application for more
information.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-27
Chapter 1
Product Overview
Network Configuration Examples
Network Configuration Examples
This section provides network configuration concepts and includes examples of
using the switch to create dedicated network segments and interconnecting the
segments through Fast Ethernet and Gigabit Ethernet connections.
Design Concepts for Using the Switch
As your network users compete for network bandwidth, it takes longer to send and
receive data. When you configure your network, consider the bandwidth required
by your network users and the relative priority of the network applications they
use. Table 1-9 describes what can cause network performance to degrade and
describes how you can configure your network to increase the bandwidth
available to your network users.
Catalyst 3500 Series XL Hardware Installation Guide
1-28
78-6456-03
Chapter 1
Product Overview
Network Configuration Examples
Table 1-9
Considerations for Increasing Network Performance
Network Demands
•
Too many users on a single
network segment and a growing
number of users accessing the
Internet
•
The increased power of new PCs,
workstations, and servers
•
High demand from networked
applications (such as e-mail with
large attached files) and from
bandwidth-intensive applications
(such as multimedia)
•
An evolving demand for IP
telephony
Suggested Design Methods
•
Create smaller network segments so that fewer users share
the bandwidth, and place the network resources in the same
logical network as the users who access those resources
most.
•
Use full-duplex operation between the switch and its
connected workstations.
•
Connect global resources—such as servers and routers to
which network users require equal access—directly to the
Fast Ethernet or Gigabit Ethernet switch ports so that they
have their own Fast Ethernet or Gigabit Ethernet segment.
•
Use the Fast EtherChannel or Gigabit EtherChannel feature
between the switch and its connected servers and routers.
•
Use quality of service (QoS) to prioritize applications such
as IP telephony during congestion and to help control both
delay and jitter within the network. Use switches that
support at least two queues per port to prioritize voice and
data traffic as either high or low priority based on
802.1p/Q.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-29
Chapter 1
Product Overview
Network Configuration Examples
You can connect the switch to other devices and create backup paths by using
Fast Ethernet or gigabit links or Fast EtherChannel or Gigabit EtherChannel links.
Using the Hot Standby Redundancy Protocol (HSRP), you can create backup
paths between Catalyst 4908G-L3 switches. Figure 1-21 illustrates three
configuration examples for using the Catalyst 3500 XL switches to create the
following:
•
Cost-effective wiring closet—A cost-effective way to connect many users to
the wiring closet is to connect up to nine Catalyst 3500 XL switches through
GigaStack GBIC connections. When you use a stack of Catalyst 3548 XL
switches, you can connect up to 432 users. To preserve connectivity between
the switches in case one switch in the stack fails, connect the bottom switch
to the top switch to create a GigaStack loopback.
Using gigabit GBIC modules on two of the switches, you can have redundant
uplink connections to a gigabit backbone switch such as the
Catalyst 3508G XL switch. If one of the redundant connections fails, the
other can serve as a backup path. You can configure the stack members and
the Catalyst 3508G XL switch as a switch cluster to manage them through a
single IP address.
•
High-performance workgroup—For users who require high-speed access to
network resources, use gigabit GBIC modules to connect the switches
directly to a backbone switch in a star configuration. Each switch in this
configuration provides users a dedicated 1-Gbps connection to network
resources in the backbone. Compare this with the switches in a GigaStack
configuration, where the 1-Gbps connection is shared among the switches.
Using gigabit GBIC modules also provides flexibility in media and distance
options:
– 1000BaseSX GBIC module: Fiber connections of up to 550 m
– 1000BaseLX/LH GBIC module: Fiber connections of up to 10 km
– 1000BaseZX GBIC module: Fiber connections of up to 100 km
•
Redundant gigabit backbone—To enhance network reliability and load
balancing for different VLANs and subnets, you can connect the
Catalyst 3500 XL switches, again in a star configuration, to two backbone
switches. If one of the backbone switches fails, the second backbone switch
preserves connectivity between the switches and network resources.
Catalyst 3500 Series XL Hardware Installation Guide
1-30
78-6456-03
Chapter 1
Product Overview
Network Configuration Examples
Figure 1-21 Example Configurations with Catalyst 3500 XL Switches
Cost-Effective Wiring Closet
Catalyst 3548 XL switch
Catalyst 3548 XL
GigaStack cluster
High-Performance Workgroup
Catalyst 3508 XL or 4908G-L3 switch
Catalyst 3500 XL cluster
Redundant Gigabit Backbone
Catalyst 3500 XL cluster
33090
Catalyst 4908G-L3 switch
Catalyst 4908G-L3 switch
1 Gbps HSRP
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-31
Chapter 1
Product Overview
Network Configuration Examples
Small- to Medium-Sized Network Configuration
Figure 1-22 illustrates a configuration for a network that has up to 250 users.
Users in this network require e-mail, file-sharing, database, and Internet access.
You optimize network performance by placing workstations on the same logical
segment as the servers they access most often. This divides the network into
smaller segments (or workgroups) and reduces the amount of traffic that travels
over a network backbone, thereby increasing the bandwidth available to each user
and improving server response time.
A network backbone is a high-bandwidth connection (such as Fast Ethernet or
Gigabit Ethernet) that interconnects segments and network resources. It is required
if numerous segments require access to the servers. The Catalyst 3500 XL
switches in this network are connected through a GigaStack GBIC on each switch
to form a 1-Gbps network backbone. This GigaStack also can be configured as a
switch cluster, with primary and secondary command switches for redundant
cluster management.
Workstations are connected directly to the 10/100 switch ports for their own
10- or 100-Mbps access to network resources (such as web and mail servers).
When a workstation is configured for full-duplex operation, it receives up to
200 Mbps of dedicated bandwidth from the switch.
Servers are connected to the gigabit GBIC module ports on the switches, allowing
1-Gbps throughput to users when needed. When the switch and server ports are
configured for full-duplex operation, the links provide 2 Gbps of bandwidth. For
networks that do not require gigabit performance from a server, connect the server
to a Fast Ethernet or Fast EtherChannel switch port.
Connecting a router to a Fast Ethernet switch port provides multiple,
simultaneous access to the Internet through one line.
Catalyst 3500 Series XL Hardware Installation Guide
1-32
78-6456-03
Chapter 1
Product Overview
Network Configuration Examples
Figure 1-22 Small- to Medium-Sized Network Configuration
Cisco 2600 router
100 Mbps
(200 Mbps full duplex)
Gigabit
server
1 Gbps
(2 Gbps full duplex)
Catalyst 3500 XL
GigaStack cluster
Gigabit
server
Single workstations
33091
10/100 Mbps
(20/200 Mbps full duplex)
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-33
Chapter 1
Product Overview
Network Configuration Examples
Collapsed Backbone and Switch Cluster Configuration
Figure 1-23 illustrates a configuration for a network of approximately
500 employees. This network uses a collapsed backbone and switch clusters. A
collapsed backbone has high-bandwidth uplinks from all segments and
subnetworks to a single device, such as a gigabit switch, which serves as a single
point for monitoring and controlling the network. You can use a
Catalyst 4908G-L3 switch, as illustrated, or a Catalyst 3508G XL switch to create
a gigabit backbone. A Catalyst 4908G-L3 backbone switch provides the benefits
of inter-VLAN routing and allows the router to focus on WAN access.
The workgroups are created by clustering the Catalyst switches except the
Catalyst 4908G-L3 switch. Using the Cisco Cluster Management Suite, you can
group the switches into multiple clusters, as illustrated, or into a single cluster.
You can manage a cluster through the IP address of its primary and secondary
command switches, regardless of the geographic location of the cluster members.
This network also includes voice and data subnetworks, where Cisco IP Phones
are connected—using standard straight-through, twisted-pair cable with RJ-45
connectors—to the 10/100 inline-power ports on the Catalyst 3524-PWR XL
switches and to the 10/100 ports on the Catalyst 3500 and 2900 XL switches.
These multiservice switch ports automatically detect if an IP phone is connected.
You also configure each port for 802.1p/Q QoS to give forwarding priority to
voice traffic over data traffic. Cisco CallManager controls call processing,
routing, and IP phone features and configuration. Users with workstations running
Cisco SoftPhone software can place, receive, and control calls from their PCs.
Using Cisco IP Phones, Cisco CallManager software, and Cisco SoftPhone
software integrates telephony and IP networks, where the IP network supports
both voice and data.
Each 10/100 inline-power port on the Catalyst 3524-PWR XL switches provides
–48V DC power to the Cisco IP Phone. The IP phone can receive redundant power
when it also is connected to an AC power source. IP phones connected to switches
other than the Catalyst 3524-PWR XL switches receive power from an AC power
source.
Grouping servers in a centralized location provides benefits such as security and
easier maintenance. The gigabit connections to a server farm provide the
workgroups full access to the network resources (such as a call-processing server
running Cisco CallManager software, a Dynamic Host Configuration Protocol
(DHCP)/Bootstrap Protocol (BOOTP) server, or an IPTV multicast server).
Catalyst 3500 Series XL Hardware Installation Guide
1-34
78-6456-03
Chapter 1
Product Overview
Network Configuration Examples
The connection between the Catalyst 3524-PWR XL switch and the router is
configured for Fast EtherChannel, increasing the bandwidth to 200 Mbps
(400 Mbps in full duplex).
Figure 1-23 Collapsed Backbone and Switch Cluster Configuration
Gigabit
servers
Cisco
CallManager
Catalyst 4908G-L3 switch
Cisco 2600 router
200 Mbps
Fast EtherChannel
(400 Mbps full duplex
Fast EtherChannel)
1 Gbps
(2 Gbps full duplex)
Catalyst
3500 XL and 2900 XL
GigaStack cluster
Catalyst
2900 XL,
1900, and
2820 cluster
Catalyst
3524-PWR XL
GigaStack cluster
IP
IP
IP
IP
IP
AC
power
source
Workstations running
Cisco SoftPhone software
IP
IP
Cisco IP Phones
33092
Cisco
IP Phones
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-35
Chapter 1
Product Overview
Network Configuration Examples
Large Campus Configuration
Figure 1-24 illustrates a configuration for a network of more than 1000 users.
Because it can aggregate up to 130 gigabit connections, a Catalyst 6500
multilayer switch is used as the backbone switch.
You can use the earlier workgroup configurations to create workgroups with
gigabit uplinks to the Catalyst 6500 switch. For example, you can use switch
clusters that have a mix of Catalyst 3500 and 2900 XL switches.
The Catalyst 6500 switch provides the workgroups with gigabit access to core
resources:
•
Cisco 7000 series router for access to the WAN and the Internet.
•
Server farm that includes a call-processing server running Cisco CallManager
software. Cisco CallManager controls call processing, routing, and IP phone
features and configuration.
•
Cisco Access gateway (such as Cisco Access Digital Trunk Gateway or Cisco
Access Analog Trunk Gateway) that connects the IP network to the Public
Switched Telephone Network (PSTN) or to users in an IP telephony network.
Catalyst 3500 Series XL Hardware Installation Guide
1-36
78-6456-03
Chapter 1
Product Overview
Network Configuration Examples
Figure 1-24 Large Campus Configuration
IP telephony
network or
PSTN
WAN
Cisco
CallManager
Cisco 7200 Cisco access
or 7500 router gateway
Servers
Catalyst
6500 switch
Catalyst
3500 XL and 2900 XL
GigaStack cluster
1 Gbps
(2 Gbps
full duplex)
Catalyst
3524-PWR XL
GigaStack cluster
IP
IP
IP
Cisco IP Phones
IP
IP
Workstations running
Cisco SoftPhone software
IP
Cisco IP Phones
33093
AC
power
source
IP
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1-37
Chapter 1
Product Overview
Network Configuration Examples
Catalyst 3500 Series XL Hardware Installation Guide
1-38
78-6456-03
C H A P T E R
2
Installing and Starting Up the Switch
This chapter describes how to install and start up your Catalyst 3500 XL switches
and to interpret the power-on self-test (POST) that ensures proper operation. Read
the topics, and perform the procedures in the order that they are presented:
•
Pre-installation information and guidelines
•
Installation procedures
•
Power-on procedures
•
Connection procedures
•
Set up procedures for initial configuration
•
Default configuration settings
•
Where to go next
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-1
Chapter 2
Installing and Starting Up the Switch
Preparing for Installation
Preparing for Installation
Warnings
These warnings are translated into several languages in Appendix C, “Translated
Safety Warnings.”
Warning
This equipment is to be installed and maintained by service
personnel only as defined by AS/NZS 3260 Clause 1.2.14.3 Service
Personnel.
Warning
Only trained and qualified personnel should be allowed to install
or replace this equipment.
Warning
Read the installation instructions before you connect the system to
its power source.
Warning
Before working on equipment that is connected to power lines,
remove jewelry (including rings, necklaces, and watches). Metal
objects will heat up when connected to power and ground and can
cause serious burns or weld the metal object to the terminals.
Warning
Do not stack the chassis on any other equipment. If the chassis
falls, it can cause severe bodily injury and equipment damage.
Warning
The plug-socket combination must be accessible at all times
because it serves as the main disconnecting device.
Catalyst 3500 Series XL Hardware Installation Guide
2-2
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Preparing for Installation
Warning
To prevent the switch from overheating, do not operate it in an area
that exceeds the maximum recommended ambient temperature of
113°F (45°C). To prevent airflow restriction, allow at least 3 inches
(7.6 cm) of clearance around the ventilation openings.
Warning
The device is designed to work with TN power systems.
Warning
When installing the unit, the ground connection must always be
made first and disconnected last.
Warning
This product relies on the building’s installation for short-circuit
(overcurrent) protection. Ensure that a fuse or circuit breaker no
larger than 120 VAC, 15A U.S. (240 VAC, 16A international) is used
on the phase conductors (all current-carrying conductors).
Warning
This equipment is intended to be grounded. Ensure that the host is
connected to earth ground during normal use.
Warning
Care must be given to connecting units to the supply circuit so that
wiring is not overloaded.
Warning
Unplug the power cord before you work on a system that does not
have an on/off switch.
Warning
Do not touch the power supply when the power cord is connected.
For systems with a power switch, line voltages are present within
the power supply even when the power switch is off and the power
cord is connected. For systems without a power switch, line
voltages are present within the power supply when the power cord
is connected.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-3
Chapter 2
Installing and Starting Up the Switch
Preparing for Installation
Warning
Do not work on the system or connect or disconnect cables during
periods of lightning activity.
Warning
Ultimate disposal of this product should be handled according to
all national laws and regulations.
The following warning applies to the Catalyst 3508, 3512, 3524, and 3548 XL
switches:
Warning
Attach only the Cisco RPS (model PWR600-AC-RPS) to the RPS
receptacle.
The following warning applies to the Catalyst 3524-PWR XL switch:
Warning
Attach only the Cisco RPS (model PWR300-AC-RPS) to the RPS
receptacle.
EMC Regulatory Statements
U.S.A.
U.S. regulatory information for this product is in the front matter of this manual.
15456
Taiwan
Catalyst 3500 Series XL Hardware Installation Guide
2-4
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Preparing for Installation
Installation Guidelines
When determining where to place the switch, be sure to observe these guidelines:
•
For 10/100 ports, cable lengths from the switch to connected devices are up to
100 meters.
•
For 1000BaseX ports, cable lengths from the switch to the connected devices
are up to 10,000 meters. For specific cable lengths, refer to the documents
that came with your GBICs.
•
For the GigaStack GBIC ports, cable lengths from the switch to the connected
devices are up to 1 meter. For specific cable lengths, refer to the document
that came with the GigaStack GBIC.
•
Operating environment is within the ranges listed in Appendix A, “Technical
Specifications.”
•
Clearance to front and rear panels is such that
– Front-panel indicators can be easily read.
– Access to ports is sufficient for unrestricted cabling.
– Rear-panel power connector is within reach of an AC power receptacle.
Note
•
Airflow around the switch and through the vents is unrestricted.
•
Temperature around the unit does not exceed 113°F (45°C).
If the switch is installed in a closed or multirack assembly, the
temperature around it might be greater than normal room
temperature.
•
Cabling is away from sources of electrical noise, such as radios, power lines,
and fluorescent lighting fixtures.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-5
Chapter 2
Installing and Starting Up the Switch
Preparing for Installation
Verifying Package Contents
Note
Carefully remove the contents from the shipping container, and
check each item for damage. If any item is missing or damaged,
contact your Cisco representative or reseller for support. Return all
packing materials to the shipping container, and save it.
The switch is shipped with the following items:
•
Quick Start: Catalyst 3500 Series XL Cabling and Setup
•
This Catalyst 3500 Series XL Hardware Installation Guide
•
Cisco IOS Desktop Switching Software Configuration Guide
•
Release Notes for the Catalyst 2900 Series XL and Catalyst 3500 Series XL
Cisco IOS Release 12.0(5)XU
•
Cisco Documentation CD-ROM
•
AC power cord
•
Mounting kit containing:
– Four rubber feet for mounting the switch on a table
– Two mounting brackets
– Four Phillips flat-head screws for attaching the brackets to the switch
– Four Phillips truss-head screws for attaching the brackets to the switch
– Four Phillips machine screws for attaching the brackets to a rack
– One cable guide and one black Phillips machine screw for attaching the
cable guide to one of the mounting brackets
•
One RJ-45-to-RJ-45 rollover cable
•
One RJ-45-to-DB-9 female adapter
•
Cisco Information Packet, containing warranty, safety, and support
information
Catalyst 3500 Series XL Hardware Installation Guide
2-6
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Installing the Switch in a Rack
Installing the Switch in a Rack
Warning
To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system
remains stable. The following guidelines are provided to ensure
your safety:
•
This unit should be mounted at the bottom of the rack if it is the
only unit in the rack.
•
When mounting this unit in a partially filled rack, load the rack
from the bottom to the top with the heaviest component at the
bottom of the rack.
•
If the rack is provided with stabilizing devices, install the
stabilizers before mounting or servicing the unit in the rack.
The rack-mounting brackets supplied with the switch can be attached to a 19- or
24-inch rack. Figure 2-1 shows which mounting holes attach to the rack.
Note
The illustrations in this section show the Catalyst 3508G XL switch
as an example. Other switches in the series (Catalyst 3512, 3524,
3524-PWR, and 3548 XL) can also be installed as shown here.
Figure 2-1
Bracket Mounting Points
24" rack
mount point
19" rack
mount point
24" rack
mount point
38398
19" rack
mount point
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-7
Chapter 2
Installing and Starting Up the Switch
Installing the Switch in a Rack
To install the switch in a 19-inch or a 24-inch standard rack, follow the
instructions described in these procedures:
•
Removing screws from the switch
•
Attaching the brackets to the switch
•
Mounting the switch in a rack
•
Attaching the optional cable guide
Removing Screws from the Switch
If you plan to install the Catalyst 3548 XL switch in a rack, you must first remove
the front side screws in the switch chassis so that the mounting brackets can be
attached. Figure 2-2 shows how to remove the chassis screw from one side of the
switch. Follow the same procedure for the opposite side.
Figure 2-2
Removing Screws from the Catalyst 3548 XL Switch
Catalyst 3548 XL switch
46
47 48
47X
2
48X
30062
1
Catalyst 3500 Series XL Hardware Installation Guide
2-8
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Installing the Switch in a Rack
Attaching the Brackets to the Switch
The bracket orientation and the screws you use depend on whether you are
attaching the brackets for a 19-inch or a 24-inch rack. Use two of the supplied
screws to attach each bracket, according to the following guidelines:
•
For a 19-inch rack, use the supplied number-8 Phillips flat-head screws to
attach the long side of the bracket to the switch.
•
For a 24-inch rack, use the supplied number-8 Phillips truss-head screws to
attach the short side of the bracket to the switch.
Figure 2-3 and Figure 2-4 show how to attach a bracket to one side of the switch.
Follow the same steps to attach the second bracket to the opposite side.
Figure 2-3
Attaching Brackets for 19- and 24-Inch Racks (Front Panel Forward)
Phillips
flat-head
screws
1
2
3
22437
SYSTEM
RPS
MODE
STATUS
UTIL
DUPLX
SPEED
19" Configuration
Phillips
truss-head
screws
1
2
STATUS
UTIL
DUPLX
SPEED
3
22438
SYSTEM
RPS
MODE
24" Configuration
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-9
Chapter 2
Installing and Starting Up the Switch
Installing the Switch in a Rack
Attaching Brackets for 19- and 24-Inch Racks (Rear Panel Forward)
22439
Figure 2-4
DC INPUTS FOR REMOTE POWER
SUPPLY
SPECIFIED IN MANUAL. +3.3V***@
14A,
+12V***@3A
DC INPUT
Phillips
flat-head
screws
22440
19" Configuration
DC INPUTS FOR REMOTE POWER
SUPPLY
SPECIFIED IN MANUAL. +3.3V***@
14A,
+12V***@3A
DC INPUT
Phillips
truss-head
screws
24" Configuration
Catalyst 3500 Series XL Hardware Installation Guide
2-10
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Installing the Switch in a Rack
Mounting the Switch in a Rack
After the brackets are attached to the switch, use the four supplied number-12
Phillips machine screws to securely attach the brackets to the rack, as shown in
Figure 2-5.
Mounting the Switch in a Rack
26233
Figure 2-5
1
SYSTEM
RPS
MODE
2
3
4
5
6
STATUS
7
8
UTIL
DUPLX
SPEED
Phillips machine
screws
After the switch is mounted in the rack, attach the power cord to the switch. If you
are using the Cisco RPS, see the Cisco RPS documentation for installation
instructions.
After the power is connected, the System LED turns amber for 2 seconds, and then
it flashes green while the switch completes the series of POST tests described in
the “Powering On the Switch and Running POST” section on page 2-15.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-11
Chapter 2
Installing and Starting Up the Switch
Installing the Switch in a Rack
Attaching the Optional Cable Guide
We recommend attaching the cable guides to prevent the cables from obscuring
the front panel of the switch and the other devices installed in the rack. If the
switch is in a 19-inch or 24-inch rack, use the supplied black screw, as shown in
Figure 2-6, to attach the cable guide to the left or right bracket.
The Catalyst 3548 XL switch ships with a special cable guide as
shown in Figure 2-7. This cable guide secures up to 48 cables. Use
the supplied black screw to mount it on the left bracket.
Note
Attaching the Cable Guide to a 3512, 3524, 3524-PWR, or 3508 XL Switch
22441
Figure 2-6
1
2
SYSTEM
MODE
3
RPS
4
5
6
STATUS
7
UTIL
8
DUPLX
SPEED
Cable guide screw
Attaching the Cable Guide to a 3548 XL Switch
28324
Figure 2-7
1
1X
2
3
4
5
6
7
8
9
10
11 12
13 14
15 16
17 18
15X
17X
16X
18X
SYSTEM
19 20
21 22
23 24
25 26
27 28
29 30
31 32
33 34
31X
33X
32X
34X
RPS
35 36
37 38
39 40
41 42
43 44
45 46
47 48
47X
STATUS
UTIL
1
DUPLEX
SPEED
MODE
2X
48X
2
Cable guide screw
Catalyst 3500 Series XL Hardware Installation Guide
2-12
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Installing the Switch on a Wall
Installing the Switch on a Wall
This section describes the steps required to attach the switch to a wall:
•
Attaching the brackets to the switch
•
Attaching the switch to a wall
Attaching the Brackets to the Switch
Use two of the supplied number-8 Phillips flat-head screws to attach the long side
of the bracket to the switch.
Figure 2-8 shows how to attach the brackets to one side of the switch. Follow the
same steps to attach the second bracket to the opposite side.
Attaching Brackets for Wall-Mounting
30060
Figure 2-8
DC INPUTS FOR REMOTE POWER
SUPPLY
SPECIFIED IN MANUAL. +3.3V***@
14A,
+12V***@3A
DC INPUT
Phillips
flat-head
screws
For vertical wall-mounting
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-13
Chapter 2
Installing and Starting Up the Switch
Installing the Switch on a Wall
Attaching the Switch to a Wall
For best support of the switch and cables, make sure the switch is attached
securely to a wall stud or to a firmly attached plywood mounting backboard, as
shown in Figure 2-9.
Figure 2-9
Attaching the Switch to a Wall
Vertical
wall stud
RPS
UTIL
SYSTEM
STATUS
DUPLEX
30061
MODE
SPEED
1
Vertical
wall-mount
2
3
4
5
6
7
8
User-supplied
screws
After the switch is mounted on the wall, attach the power cord to the switch. If
you are using the RPS, see the Cisco RPS documentation.
After the power is connected, the system LED turns amber for 2 seconds, and then
it flashes green while the switch completes a series of self-tests described in the
“Powering On the Switch and Running POST” section on page 2-15.
Catalyst 3500 Series XL Hardware Installation Guide
2-14
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Installing the Switch on a Table or Shelf
Installing the Switch on a Table or Shelf
Follow these steps to install the switch on a table or shelf:
Step 1
Locate the adhesive strip with the rubber feet in the mounting-kit envelope. Attach
the four rubber feet to the recessed areas on the bottom of the unit.
Step 2
Place the switch on the table or shelf near an AC power source.
Step 3
Connect the power cord to the switch rear panel and to the power outlet. If you are
using the RPS, see the RPS documentation for installation instructions.
After the power is connected, the system LED turns amber for 2 seconds, and then
it flashes green while the switch completes POST.
Powering On the Switch and Running POST
If your configuration has an RPS, see the “Power Connectors” section on
page 1-25 and the Cisco RPS documentation.
To power on the switch after you install it, follow these steps:
Step 1
Make sure that you have started the emulation software program (such as ProComm,
HyperTerminal, tip, or minicom) from your management station.
Step 2
Connect one end of the AC power cord to the AC power connector on the switch.
Step 3
Connect the other end of the power cord to an AC power outlet.
As the switch powers on, it begins POST, a series of eight tests that run
automatically to ensure that the switch functions properly. When the switch
begins POST, the port LEDs turn amber for 2 seconds, and then they turn green.
The System LED flashes green, and the RPS LED turns off. As each test runs, the
port LEDs, starting with number 1, turn off. The port LEDs for ports 2 to 8 each
turn off in turn as the system completes a test.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-15
Chapter 2
Installing and Starting Up the Switch
Connecting to the 10/100 Ports
When POST completes successfully, the port LEDs return to the status mode
display, indicating that the switch is operational. If a test fails, the port LED
associated with the test turns amber, and the system LED turns amber. If POST
fails, refer to Chapter 3, “Troubleshooting,” to determine a course of action.
POST failures are usually fatal. Call Cisco Systems immediately if your switch
does not pass POST.
Connecting to the 10/100 Ports
The switch 10/100 Ethernet ports configure themselves to operate at the speed of
attached devices. If the attached ports do not support autonegotiation, you can
explicitly set the speed and duplex parameters.
Connecting devices that do not autonegotiate or that have their speed and duplex
parameters manually set can reduce performance or result in no linkage. To
maximize performance, choose one of these methods for configuring the 10/100
Ethernet ports:
•
Let the ports autonegotiate both speed and duplex.
•
Set the port speed and duplex parameters on both ends of the connection.
You can configure the 10/100 ports on the Catalyst 3524-PWR XL switch to
either automatically provide inline power when a Cisco IP Phone is connected or
to never provide inline power even if a Cisco IP Phone is connected. The default
setting is Auto.
Caution
It takes a Catalyst 3524-PWR XL 10/100 port up to 10 seconds to
initially detect, power, and link to a Cisco IP Phone. If you
disconnect the Cisco IP Phone before link has been established, you
must wait 10 seconds before connecting another network device
(other than another Cisco IP Phone) to that switch port. Failure to
do so can result in damage to that network device.
Catalyst 3500 Series XL Hardware Installation Guide
2-16
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Connecting to the 10/100 Ports
Follow these steps to connect to 10BaseT and 100BaseTX devices:
Step 1
When connecting to workstations, servers, routers, and Cisco IP Phones, connect
a straight-through Category 5 cable to an RJ-45 connector on the front panel
(Figure 2-10). When connecting to switches or repeaters, use a crossover
Category 5 cable. Pinouts for the cables are described in the “Crossover and
Straight-Through Cable Pinouts” section on page B-4.
Figure 2-10 Connecting to a 10/100 Switch Port
1
2
3
4
5
6
7
8
9
10
11 12
1X
11X
SYSTEM
RPS
Note
STATUS
UTIL
DUPLX
SPEED
2X
12X
22001
MODE
The Catalyst 3524-PWR XL switch can connect to a Cisco IP Phone
through a straight-through, twisted-pair cable. The rear panel of the
Cisco IP Phone might have more than one RJ-45 jack. Use the
LAN-to-phone jack to connect the phone to the
Catalyst 3524-PWR XL switch. Refer to the documentation that
came with your Cisco IP Phone for information about connecting
devices to it.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-17
Chapter 2
Installing and Starting Up the Switch
Connecting to the 10/100 Ports
Step 2
Connect the other end of the cable to an RJ-45 connector of the other device. The
port LED comes on when both the switch and the connected device have
established link.
The port LED is amber while Spanning Tree Protocol (STP) discovers the
topology and searches for loops. This takes about 30 seconds, and then the port
LED turns green.
If the port LED does not come on, the device at the other end might not be turned
on, or there might be a cable problem or a problem with the adapter installed in
the attached device. See Chapter 3, “Troubleshooting,” for solutions to cabling
problems.
Step 3
Reconfigure and reboot the connected device if necessary.
Step 4
Repeat steps 1 through 3 to connect each device.
Catalyst 3500 Series XL Hardware Installation Guide
2-18
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Connecting to the GBIC Module Ports
Connecting to the GBIC Module Ports
Note
Install the Gigabit Interface Converters (GBICs) as described in the
“GBIC Module Slots” section on page 1-10, and then connect to the
1000BaseX ports.
For detailed instructions on installing, removing, and cabling the GBICs
(1000BaseSX module or the 1000BaseLX/LH module), refer to the GBIC
documentation.
For detailed instructions on installing and cabling the GigaStack GBICs, see the
Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide.
Connecting to a 1000BaseX GBIC Module Port
Caution
Do not remove the rubber plugs from the fiber-optic port or the
rubber caps from the fiber-optic cable until you are ready to connect
the cable. The plugs and caps protect the fiber-optic port and cable
from contamination and ambient light.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-19
Chapter 2
Installing and Starting Up the Switch
Connecting to the GBIC Module Ports
Follow these steps to connect to the 1000BaseX port:
Step 1
Remove the rubber plugs from the fiber-optic port on the module, and store them
for future use.
Step 2
Insert the SC connector in the fiber-optic receptacle, as shown in Figure 2-11.
Figure 2-11 Connecting to a 1000BaseX Port
1
SYSTEM
RPS
Note
2
STATUS
UTIL
DUPLX
SPEED
22005
MODE
The port status is amber while Spanning Tree Protocol discovers the
topology and searches for loops. This takes about 30 seconds. The
port LED then turns green.
Catalyst 3500 Series XL Hardware Installation Guide
2-20
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Connecting to the GBIC Module Ports
Connecting to a GigaStack GBIC Module Port
Connect the GigaStack cable connector to the GigaStack GBIC as shown in
Figure 2-12.
Figure 2-12 Connecting to a GigaStack Port
1
2
SYSTEM
RPS
MODE
STATUS
UTIL
32708
DUPLX
SPEED
1
2
1
2
1394
GigaStack cable
1394
For more information on the GigaStack GBIC connections and configuration
scenarios, see the Catalyst GigaStack Gigabit Interface Converter Hardware
Installation Guide.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-21
Chapter 2
Installing and Starting Up the Switch
Connecting a PC or Terminal to the Console Port
Connecting a PC or Terminal to the Console Port
Use the supplied rollover cable and DB-9 adapter to connect a PC to the switch
console port. You need to provide a RJ-45-to-DB-25 female DTE adapter if you
want to connect the switch console port to a terminal. You can order a kit
(part number ACS-DSBUASYN=) containing that adapter from Cisco. For
console port and adapter pinout information, see the “Cable and Adapter
Specifications” section on page B-4.
The PC or terminal must support VT100 terminal emulation. The
terminal-emulation software—frequently a PC application such as Hyperterminal
or Procomm Plus—makes communication between the switch and your PC or
terminal possible during the setup program.
Follow these steps to connect the PC or terminal to the switch:
Step 1
Be sure that your PC- or terminal-emulation software is configured to
communicate with the switch via hardware flow control.
Step 2
Configure the baud rate and character format of the PC or terminal to match these
console port default characteristics:
•
9600 baud
•
8 data bits
•
1 stop bit
•
No parity
After you have gained access to the switch, you can change the port baud rate. See
the Cisco IOS Desktop Switching Software Configuration Guide for instructions.
Catalyst 3500 Series XL Hardware Installation Guide
2-22
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Connecting a PC or Terminal to the Console Port
Step 3
Using the supplied rollover cable, insert the RJ-45 connector into the console port,
as shown in Figure 2-13. See the “Identifying a Rollover Cable” section on
page B-5 for a description of the pinout.
32709
Figure 2-13 Connecting to the Console Port
CONSOLE
DC INPUTS FOR REMOTE
POWER SUPPLY
SPECIFIED IN MANUAL.
+5V @24A, +12V @1.0A
RJ-45
Console port
Rollover cable
Step 4
Attach the supplied RJ-45-to-DB-9 female DTE adapter to a PC or attach an
appropriate adapter to the terminal.
Step 5
Insert the other end of the supplied rollover cable in the attached adapter.
Step 6
Boot the terminal-emulation program if you are using a PC or terminal.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-23
Chapter 2
Installing and Starting Up the Switch
Assigning Switch Information
Assigning Switch Information
You can assign the switch IP address information, host and cluster names, and
passwords by two methods:
•
Using the setup program in the switch
•
Using a BOOTP server
This section describes each method.
Using the Setup Program
You can use an automatic setup program to assign IP information and to create a
default configuration for continued operation. Later, you can use the Cluster
Management Suite or the command-line interface (CLI) to customize your
configuration. To run the setup program, access the switch from the PC terminal
that you connected to the console port. (See the “Connecting a PC or Terminal to
the Console Port” section on page 2-22.)
Note
If the switch will be a cluster member, it is not always necessary to
assign IP information or a password, as the switch will be managed
through the IP address of the command switch. If you are
configuring a command switch or standalone switch, you need to
assign IP information.
The first time that you access the switch, it runs a setup program that prompts you
for IP and other configuration information necessary for the switch to
communicate with local routers and the Internet. This information also is required
if you plan to use the Cluster Management Suite to configure and manage the
switch.
Note
If the switch will be a cluster member managed through the IP
address of the command switch, it is not necessary to assign IP
information or a password. If you are configuring the switch as a
standalone switch or as a command switch, you must assign IP
information. Refer to the Cisco IOS Desktop Switching Software
Configuration Guide for more information.
Catalyst 3500 Series XL Hardware Installation Guide
2-24
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Assigning Switch Information
You will need the following information from your system administrator:
Switch IP address
___________.___________.___________._________
Subnet mask (netmask)
___________.___________.___________._________
Default gateway (router) ___________.___________.___________._________
Enable secret password
___________________________________________
Use this procedure to create an initial configuration for the switch:
Note
Step 1
Be sure the rollover cable is connecting a PC serial port to the switch
console port. The data characteristics are 9600 baud, 8 data bits,
1 stop bit, and no parity. Use the supplied rollover cable and DB-9
adapter to connect a PC to the switch console port. You need to
provide a RJ-45-to-DB-25 female DTE adapter if you want to
connect the switch console port to a terminal. You can order a kit
(part number ACS-DSBUASYN=) containing that adapter from
Cisco. For console port and adapter pinout information, see the
“Cable and Adapter Specifications” section on page B-4.
Enter Y at the prompt:
Continue with configuration dialog? [yes/no]: y
If this prompt does not appear, enter enable, and press Return. Enter setup, and
press Return to restart the setup program.
Step 2
Enter the switch IP address, and press Return:
Enter IP address: ip_address
Step 3
Enter the subnet mask (IP netmask) address, and press Return:
Enter IP netmask: ip_netmask
Step 4
Enter Y to specify a default gateway (router):
Would you like to enter a default gateway address? [yes]: y
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-25
Chapter 2
Installing and Starting Up the Switch
Assigning Switch Information
Step 5
Enter the IP address of the default gateway, and press Return:
IP address of the default gateway: ip_address
Step 6
Enter a host name for the switch, and press Return:
Note
On a command switch, the host name is limited to
28 characters; on a member switch to 31 characters. Do not
use -n, where n is a number, as the last characters in a host
name for any switch.
Enter host name: host_name
Step 7
Enter a secret password (which ensures switch security), and press Return:
Note
The secret password can be from 1 to 25 alphanumeric
characters, can start with a number, is case-sensitive, and
allows spaces but ignores leading spaces.
Enter enable secret: secret_password
Step 8
Enter Y to enter a Telnet password:
Would you like to configure a Telnet password? [yes]: y
Step 9
Enter the Telnet password, and press Return:
Note
The Telnet password can be from 1 to 25 alphanumeric
characters, is case-sensitive, allows spaces, but ignores
leading spaces.
Enter Telnet password: telnet_password
Step 10
Enter Y to configure this switch as the cluster command switch. Enter N to
configure it as a member switch or as a standalone switch.
Note
If you enter N to configure the switch as a member switch or
as a standalone, it appears as a candidate switch in Cluster
Builder and the Step 11 message is not displayed.
Would you like to enable as a cluster command switch? y
Catalyst 3500 Series XL Hardware Installation Guide
2-26
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Assigning Switch Information
Step 11
Assign a name to the cluster, and press Return:
Note
The cluster name can be 1 to 31 alphanumeric characters,
dashes, or underscores.
Enter cluster name: cls_name
Step 12
Verify that the addresses are correct in the initial configuration displayed:
The following configuration command script was created:
ip subnet-zero
interface VLAN1
ip address ip_address ip_netmask
ip default-gateway ip_address
hostname host_name
enable secret 5 $1$jJql$VA6U.6uTjsa56Xx2yy/t30
line vty 0 15
password telnet_password
snmp community private rw
snmp community public ro
cluster enable cls_name
!
end
!
Use this configuration? [yes/no]:
Step 13
If the information is correct, enter Y at the prompt, and press Return to use the
displayed configuration. When you see the message “Press RETURN to get
started,” the setup program is complete. You can use your browser and the Cluster
Management Suite or use the CLI to manage the switch.
If the information is not correct, enter N at the prompt, press Return, and begin
again at Step 1.
The Cisco IOS Desktop Switching Software Configuration Guide describes how
to set a password to protect the switch against unauthorized Telnet access and how
to access the switch if you forget the password.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-27
Chapter 2
Installing and Starting Up the Switch
Assigning Switch Information
Using BOOTP
You can use BOOTP to assign IP information to a Catalyst 3500 XL switch. A
database with a list of physical MAC addresses and corresponding IP addresses
must be set up on the BOOTP server. Other optional information, such as the
corresponding subnet masks and default gateway addresses, can also be stored in
the database. The switch must be able to access the BOOTP server through one of
its ports.
If the switch starts and no IP address has been assigned, it transmits a BOOTP
broadcast request to all of its connected ports, requesting a mapping for its
physical MAC address. A valid response includes the IP address, which is
mandatory, and the subnet mask and the default gateway, which are optional.
The reception of a valid BOOTP response immediately activates the rest of the
system protocol suite, without requiring a system reset. The running configuration
is set, but the saved configuration in Flash memory is not automatically updated.
To save the IP information, log in to the CLI, and enter the write memory
command. The IP information is then preserved, and the switch does not issue
BOOTP messages the next time it resets.
Catalyst 3500 Series XL Hardware Installation Guide
2-28
78-6456-03
Chapter 2
Installing and Starting Up the Switch
Default Configuration Settings
Default Configuration Settings
After you assign IP information, the switch can operate with the default
configuration settings shown in Table 2-1.
Table 2-1
Default Configuration Settings
Feature
Default Setting
Management
Switch IP address, subnet mask, and
default gateway
User-assigned values entered in the setup
program.
Cluster command status
Enabled.
Cluster name
User-assigned value entered in the setup
program.
CDP1
Enabled.
2
Enabled.
ARP
Static address assignment
None assigned.
Network View
Always available.
3
VLAN membership
All ports are static-access ports in VLAN 1.
Performance
Autonegotiation of duplex mode
Enabled.
Autonegotiation of port speeds
Enabled.
Flooding Control
Broadcast storm control
Disabled.
Flooding unknown unicast and multicast packets Enabled.
Network port
CGMP
4
Disabled.
Enabled.
Network Redundancy
Spanning Tree Protocol
Enabled.
Port grouping
None assigned.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
2-29
Chapter 2
Installing and Starting Up the Switch
Where to Go Next
Table 2-1
Default Configuration Settings (continued)
Feature
Default Setting
Diagnostics
SPAN5 port monitoring
Disabled.
Console, buffer, and file logging
Disabled.
Security
Password
None.
Addressing security
Disabled.
Trap manager
0.0.0.0
Community strings
public.
Port security
Disabled.
Inline Power
Inline power mode
Auto.
1. CDP = Cisco Discovery Protocol
2. ARP = Address Resolution Protocol
3. VLAN = Virtual Local Area Network
4. CGMP = Cisco Group Management Protocol
5. SPAN = Switched Port Analyzer
Where to Go Next
If the default configuration shown in Table 2-1 is satisfactory, the switch does not
need further configuration. You can use any of the following management options
to change the default configuration:
•
Start the Cluster Management Suite, as described in the Cisco IOS Desktop
Switching Software Configuration Guide, and configure the switch as a
member of a cluster or as an individual switch. Refer to the release notes on
CCO for the most current browser requirements.
•
Use the CLI to configure the switch from the console. See Cisco IOS Desktop
Switching Command Reference for information on using the CLI with
Catalyst 3500 XL switches.
•
Start an SNMP application such as the CiscoView application.
Catalyst 3500 Series XL Hardware Installation Guide
2-30
78-6456-03
C H A P T E R
3
Troubleshooting
The LEDs on the front panel provide troubleshooting information about the
switch. They show failures in the power-on self-test (POST), port-connectivity
problems, and overall switch performance. For a full description of the switch
LEDs, see the “LEDs” section on page 1-12.
You can also get statistics from the browser interface, from the command-line
interface (CLI), or from an Simple Network Management Protocol (SNMP)
workstation. See the Cisco IOS Desktop Switching Software Configuration Guide,
the Cisco IOS Desktop Switching Command Reference (online only), or the
documentation that came with your SNMP application for details.
This chapter describes the following topics for troubleshooting problems:
•
Understanding POST results
•
Diagnosing problems
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
3-1
Chapter 3
Troubleshooting
Understanding POST Results
Understanding POST Results
Table 3-1 lists the eight POST tests and their associated LEDs.
POST tests run automatically each time the switch is powered on. When the
switch begins POST, the port LEDs turn amber for 2 seconds, and then they turn
green. The System LED flashes green, and the RPS LED turns off. As each test
runs, the port LEDs, starting with number 1, turn off. The port LEDs for ports 2
to 8 each turn off in turn as the system completes a test.
When POST completes successfully, the port LEDs return to the status mode
display, indicating that the switch is operational. If a test fails, the port LED
associated with the test turns amber, and the system LED turns amber.
Note
POST failures are usually fatal. Call Cisco Systems if your switch
does not pass POST.
Table 3-1
POST Test Descriptions
Switch LED
Component Tested
LED 1
DRAM
LED 2
Flash memory
LED 3
Switch CPU
LED 4
System board
LED 5
CPU interface ASIC
LED 6
Switch core ASIC
LED 7
Ethernet controller ASIC
LED 8
Ethernet interfaces
Catalyst 3500 Series XL Hardware Installation Guide
3-2
78-6456-03
Chapter 3
Troubleshooting
Diagnosing Problems
Diagnosing Problems
Common switch problems fall into the following categories:
•
Poor performance
•
No connectivity
•
Corrupted software
Table 3-2 describes how to detect and resolve these problems.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
3-3
Chapter 3
Troubleshooting
Diagnosing Problems
Table 3-2
Common Problems and Their Solutions
Symptom
Possible Cause
Resolution
Poor performance or excessive
errors.
Duplex autonegotiation mismatch.
See the Cisco IOS Desktop
Switching Software
Configuration Guide for
information on identifying
autonegotiation mismatches.
Cabling distance exceeded.
•
Port statistics show excessive
frame check sequence (FCS),
late-collision, or alignment
errors.
•
See the Cisco IOS Desktop
Switching Software
Configuration Guide for
information on displaying
port statistics.
•
For 100BaseTX connections:
•
Reduce the cable length to
within the recommended
distances.
– The distance between the
port and the attached device
exceeds 100 meters.
See your 100BaseT repeater
documentation for cabling
guidelines.
– If the switch is attached to a
repeater, the total distance
between the two end
stations exceeds the
100BaseT cabling
guidelines.
•
For 10BaseT connections: The
distance between the port and
the attached device exceeds 100
meters.
•
Reduce the cable length to
within the recommended
distances.
Bad adapter in attached device.
•
Excessive errors found in port
statistics.
•
Run adapter card diagnostic
utility.
•
STP checking for possible
loops.
•
Wait 30 seconds for LED to
turn green.
Catalyst 3500 Series XL Hardware Installation Guide
3-4
78-6456-03
Chapter 3
Troubleshooting
Diagnosing Problems
Table 3-2
Common Problems and Their Solutions (continued)
Symptom
Possible Cause
Resolution
No connectivity.
Incorrect or bad cable.
The following are indicated by no
link at both ends:
•
For the correct pinouts and
the proper application of
crossover vs.
straight-through cables, see
the “Crossover and
Straight-Through Cable
Pinouts” section on
page B-4.
•
A crossover cable was used
when a straight-through was
required, or vice-versa.
•
The cable is wired incorrectly.
•
Replace with a tested good
cable.
•
STP checking for possible
loops.
•
Wait 30 seconds for LED to
turn green.
Unreadable characters on the
management console.
Incorrect baud rate.
Reset the emulation software to
9600 baud.
System LED is amber on the
Catalyst 3508, 3512, or 3524 XL
switch.
Nonfatal or fatal POST error
detected.
Use the show POST command
to see which POST test failed.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
3-5
Chapter 3
Troubleshooting
Diagnosing Problems
Table 3-2
Common Problems and Their Solutions (continued)
Symptom
Possible Cause
System LED is amber on the
Catalyst 3524-PWR XL.
Resolution
•
Internal fan fault detected.
•
Either check the switch
itself or use the show env
command to check if a fan
on the switch has failed.
The
Catalyst 3524-PWR XL
switch can operate normally
with one failed fan. Replace
the switch at your
convenience.
•
Switch is overheating.
•
Use the show env command
to check if an
overtemperature condition
exists. If it does:
– Place the switch in an
environment that is
within 32 to 113°F
(0 to 45°C).
– Make sure fan intake
and exhaust areas are
clear.
If a multiple-fan failure is
causing the switch to
overheat, replace the
switch.
•
Cisco IP Phone fails to power on
when connected to a
Catalyst 3524-PWR XL switch.
Nonfatal or fatal POST error
detected.
Improper cabling.
•
Use the show POST
command to see which
POST test failed.
Make sure the switch is
connected to the LAN-to-phone
jack on the Cisco IP Phone.
Catalyst 3500 Series XL Hardware Installation Guide
3-6
78-6456-03
A P P E N D I X
A
Technical Specifications
Table A-1, Table A-2, and Table A-3, list the technical specifications for the
Catalyst 3500 series XL switches. Table A-4 lists the regulatory agency
approvals.
Table A-1
Technical Specifications for the Catalyst 3508G XL Switch
Environmental Ranges
Operating temperature
32 to 113°F (0 to 45°C)
Storage temperature
–4 to 149°F (–10 to 65°C)
Operating humidity
10 to 85% (noncondensing)
Operating altitude
Up to 10,000 ft (3000 m)
Storage altitude
Up to 15,000 ft (4570 m)
Power Requirements
AC input voltage
100 to 127/200 to 240 VAC
(autoranging) 50 to 60 Hz
DC input voltages
+3.3V @14A,
+12V @3A
Power consumption
82.2W
280 Btus per hour
Physical Dimensions
Weight
12 lb (5.45 kg)
Dimensions (H x W x D)
1.75 x 16 x 17.5 in.
(4.45 x 40.46 x 44.45 cm)
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
A-1
Appendix A
Table A-2
Technical Specifications
Technical Specifications for the Catalyst 3512, 3524, and 3548 XL Switches
Catalyst 3512 XL
Catalyst 3524 XL
Catalyst 3548 XL
Operating
temperature
32 to 113°F (0 to 45°C)
32 to 113°F (0 to 45°C)
32 to 113°F (0 to 45°C)
Storage
temperature
–4 to 149°F (–10 to 65°C) –4 to 149°F (–10 to 65°C) –4 to 149°F (–10 to 65°C)
Relative
humidity
10 to 85%
(noncondensing)
Operating
altitude
Up to 10,000 ft (3000 m) Up to 10,000 ft (3000 m) Up to 10,000 ft (3000 m)
Storage altitude
15,000 ft (4570 m)
Environmental Ranges
10 to 85%
(noncondensing)
15,000 ft (4570 m)
10 to 85%
(noncondensing)
15,000 ft (4570 m)
Power Requirements
AC input
voltage
100 to 127/200 to 240
100 to 127/200 to 240
100 to 127/200 to 240
VAC
VAC
VAC
(autoranging) 50 to 60 Hz (autoranging) 50 to 60 Hz (autoranging) 50 to 60 Hz
DC input
voltages
+5V @8.0A,
+12V @0.5A
+5V @10A,
+12V @0.5A
+3.3V @17A
+12V @1.1A
Power
consumption
50W
171 Btus per hour
75W
256 Btus per hour
100W
600 Btus per hour
10.25 lb (4.65 kg)
8.5 lb (3.86 kg)
12 lb (5.45 kg)
Physical Dimensions
Weight
Dimensions (H x 1.75 x 11.82 x 17.5 in.
1.75 x 11.82 x 17.5 in.
1.73 x 15.34 x 17.5 in
D x W)
(4.45 x 30.02 x 44.45 cm) (4.45 x 30.02 x 44.45 cm) (4.39 x 39.0 x 44.45 cm)
Catalyst 3500 Series XL Hardware Installation Guide
A-2
78-6456-03
Appendix A
Technical Specifications
Table A-3
Technical Specifications for the Catalyst 3524-PWR XL Switch
Environmental Ranges
Operating temperature
32 to 113°F (0 to 45°C)
Storage temperature
–4 to 149°F (–10 to 65°C)
Operating humidity
10 to 85% (noncondensing)
Operating altitude
Up to 10,000 ft (3000 m)
Storage altitude
Up to 15,000 ft (4570 m)
Power Requirements
AC input voltage
100 to 127/200 to 240 VAC
(autoranging) 50 to 60 Hz
DC input voltages
−48V
+12V
Power consumption
325W1
1100 Btus per hour
@3A,
@6A
Physical Dimensions
Weight
10.25 lb (4.65 kg)
Dimensions (H x W x D)
1.75 x 11.82 x 17.5 in.
(4.45 x 30.02 x 44.45 cm)
1. The actual power consumption depends on the number of IP phones connected.
325W represents 24 IP phones connected.
Table A-4
Catalyst 3500 Series XL Agency Approvals
Safety
EMC
UL to UL 1950, Third Edition
FCC Part 15 Class A
c-UL to CAN/CSA 22.2 No. 950-95, Third Edition
EN 55022 Class A (CISPR 22 Class A)
TUV/GS to EN 60950 with Amendment A1-A4 and A11 VCCI Class A
ACA/A2LA to AS/NZS 3260 and TS001-1997
AS/NZS 3548 Class A
CB to IEC 60950 with all country deviations
BSMI
NOM to NOM-019-SCFI
CE Marking
CE Marking
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
A-3
Appendix A
Technical Specifications
Catalyst 3500 Series XL Hardware Installation Guide
A-4
78-6456-03
A P P E N D I X
B
Connector and Cable Specifications
This appendix describes the Catalyst 3500 XL switch ports and the cables and
adapters that you use to connect the switch to other devices.
Connector Specifications
10/100 Ports
The 10/100 Ethernet ports use standard RJ-45 connectors and Ethernet pinouts
with internal crossovers, as indicated by an X in the port name. These ports have
their transmit (TD) and receive (RD) signals internally crossed so that a
straight-through cable and adapter can be attached to the port. Figure B-1 shows
the pinout.
When connecting the 10/100 ports to compatible workstations, servers, routers,
and Cisco IP Phones, you must use a straight-through cable wired for 10BaseT
and 100BaseTX (Figure B-5 illustrates the straight-through cable schematics).
When connecting to other switches or repeaters, ensure that you use a crossover
cable. (Figure B-4 illustrates the crossover cable schematics.)
Note
Use a straight-through cable to connect two ports when one of the
ports is designated with an X. Use a crossover cable to connect two
ports when both ports are designated with an X or when both ports
do not have an X.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
B-1
Appendix B
Connector and Cable Specifications
Connector Specifications
Figure B-1
10/100 Port Pinouts
Label
1
RD+
2
RD-
3
TD+
4
NC
5
NC
6
TD-
7
NC
8
NC
1 2 3 4 5 6 7 8
H5318
Pin
1000BaseX Ports
1000BaseX ports use duplex SC connectors, as shown in Figure B-2.
1000BaseX SC Connector
H8707
Figure B-2
Tx
Rx
Catalyst 3500 Series XL Hardware Installation Guide
B-2
78-6456-03
Appendix B
Connector and Cable Specifications
Connector Specifications
Gigastack Port
The GigaStack Gigabit Interface Converter (GBIC) uses proprietary connectors,
as shown in Figure B-3.
GigaStack Connector
22084
Figure B-3
The GigaStack GBIC cables are proprietary, high-data-rate cables with enhanced
signal integrity and EMI performance.
Caution
Do not use standard IEEE 1394 cables with the GigaStack GBIC.
Console Port
The console port uses an 8-pin RJ-45 connector, described in Table B-1 and
Table B-2. The supplied RJ-45-to-RJ-45 rollover cable and DB-9 adapter are used
to connect the console port of the switch to a console PC. You need to provide a
RJ-45-to-DB-25 female DTE adapter if you want to connect the switch console
port to a terminal. You can order a kit (part number ACS-DSBUASYN=)
containing that adapter from Cisco. For console port and adapter pinout
information, see Table B-1 and Table B-2.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
B-3
Appendix B
Connector and Cable Specifications
Cable and Adapter Specifications
Cable and Adapter Specifications
Crossover and Straight-Through Cable Pinouts
The schematics of crossover and straight-through cables are shown in Figure B-4
and Figure B-5.
Switch
Switch
3 TD+
6 TD–
3 TD+
6 TD–
1 RD+
2 RD–
1 RD+
2 RD–
Figure B-5
H5579
Crossover Cable Schematic
Straight-Through Cable Schematic
Switch
Switch
3 TD+
6 TD–
3 RD+
6 RD–
1 RD+
2 RD–
1 TD+
2 TD–
H5578
Figure B-4
Catalyst 3500 Series XL Hardware Installation Guide
B-4
78-6456-03
Appendix B
Connector and Cable Specifications
Cable and Adapter Specifications
Rollover Cable and Adapter Pinouts
Identifying a Rollover Cable
To identify a rollover cable, compare the two modular ends of the cable. Hold the
cable ends side-by-side, with the tab at the back. The wire connected to the pin on
the outside of the left plug should be the same color as the wire connected to the
pin on the outside of the right plug (see Figure B-6).
Figure B-6
Identifying a Rollover Cable
Pin 1 on one connector and
pin 8 on the other connector
should be the same color.
Pin 8
H10632
Pin 1
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
B-5
Appendix B
Connector and Cable Specifications
Cable and Adapter Specifications
Connecting to a PC
Use the supplied thin, flat, RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-9
female DTE adapter to connect the console port to a PC running
terminal-emulation software. Figure B-7 shows how to connect the console port
to a PC. Table B-1 lists the pinouts for the console port, the RJ-45-to-RJ-45
rollover cable, and the RJ-45-to-DB-9 female DTE adapter.
Connecting the Console Port to a PC
PC
Catalyst 3500 series XL switch
RJ-45-to-RJ-45
rollover cable
Table B-1
RJ-45-to-DB-9 adapter
(labeled TERMINAL)
PC
22003
Figure B-7
Console Port Signaling and Cabling Using a DB-9 Adapter
Console
Port (DTE)
RJ-45-to-RJ-45
Rollover Cable
RJ-45-to-DB-9
Terminal Adapter
Console
Device
Signal
RJ-45 Pin
RJ-45 Pin
DB-9 Pin
Signal
RTS
1
8
8
CTS
Not connected 2
7
6
DSR
TxD
3
6
2
RxD
GND
4
5
5
GND
GND
5
4
5
GND
RxD
6
3
3
TxD
Not connected 7
2
4
DTR
CTS
1
7
RTS
8
Catalyst 3500 Series XL Hardware Installation Guide
B-6
78-6456-03
Appendix B
Connector and Cable Specifications
Cable and Adapter Specifications
Connecting to a Terminal
Use the thin, flat, RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-25 female DTE
adapter to connect the console port to a terminal. Table B-2 lists the pinouts for
the console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25
female DTE adapter.
Note
The RJ-45-to-DB-25 female DTE adapter is not supplied with the
switch. You can order a kit (part number ACS-DSBUASYN=)
containing this adapter from Cisco.
Table B-2
Console Port Signaling and Cabling Using a DB-25 Adapter
Console
Port (DTE)
RJ-45-to-RJ-45
Rollover Cable
RJ-45-to-DB-25
Terminal Adapter
Console
Device
Signal
RJ-45 Pin
RJ-45 Pin
DB-25 Pin
Signal
RTS
1
8
5
CTS
Not connected 2
7
6
DSR
TxD
3
6
3
RxD
GND
4
5
7
GND
GND
5
4
7
GND
RxD
6
3
2
TxD
Not connected 7
2
20
DTR
CTS
1
4
RTS
8
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
B-7
Appendix B
Connector and Cable Specifications
Cable and Adapter Specifications
Catalyst 3500 Series XL Hardware Installation Guide
B-8
78-6456-03
A P P E N D I X
C
Translated Safety Warnings
This appendix repeats in multiple languages the warnings in this guide. These
translated warnings can be used with other documents related to this guide.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-1
Appendix C
Translated Safety Warnings
Attaching the Cisco RPS (model PWR600-AC-RPS)
Attaching the Cisco RPS (model PWR600-AC-RPS)
This warning applies to the Catalyst 3508, 3512, 3524, and 3548 XL switches.
Warning
Waarschuwing:
Varoitus
Avertissement :
Warnung:
Avvertenza.
Advarsel!
Attach only the Cisco RPS (model PWR600-AC-RPS) to the RPS
receptacle.
Slechts de Cisco RPS (model PWR600-AC-RPS) aan de RPS
contactdoos verbinden.
Kiinnitä RPS-vastakappaleeseen vain Cisco RPS (malli
PWR600-AC-RPS).
Raccordez le bloc d’alimentation Cisco RPS (modèle
PWR600-AC-RPS) uniquement au connecteur RPS.
An die RPS-Steckhülse darf nur das Cisco RPS (Modell
PWR600-AC-RPS) angeschlossen werden.
Collegare soltanto il Cisco RPS (modello PWR600-AC-RPS) alla
presa RPS.
Koble bare Cisco RPS (modell PWR600-AC-RPS) til
RPS-stikkontakten.
Aviso
Anexe o RPS Cisco (modelo PWR600-AC-RPS) apenas ao
receptáculo RPS.
Aviso:
Sólo conecte el Cisco RPS (modelo PWR600-AC-RPS) al
receptáculo RPS.
Varning!
Koppla endast Ciscos RPS (modell PWR600-AC-RPS) till
RPS-uttaget.
Catalyst 3500 Series XL Hardware Installation Guide
C-2
78-6456-03
Appendix C
Translated Safety Warnings
Attaching the Cisco RPS (model PWR300-AC-RPS)
Attaching the Cisco RPS (model PWR300-AC-RPS)
This warning applies to the Catalyst 3524-PWR XL switch.
Warning
Waarschuwing:
Varoitus
Avertissement :
Warnung:
Avvertenza.
Advarsel!
Attach only the Cisco RPS (model PWR300-AC-RPS) to the RPS
receptacle.
Slechts de Cisco RPS (model PWR300-AC-RPS) aan de RPS
contactdoos verbinden.
Kiinnitä RPS-vastakappaleeseen vain Cisco RPS (malli
PWR300-AC-RPS).
Raccordez le bloc d’alimentation Cisco RPS (modèle
PWR300-AC-RPS) uniquement au connecteur RPS.
An die RPS-Steckhülse darf nur das Cisco RPS (Modell
PWR300-AC-RPS) angeschlossen werden.
Collegare soltanto il Cisco RPS (modello PWR300-AC-RPS) alla
presa RPS.
Koble bare Cisco RPS (modell PWR300-AC-RPS) til
RPS-stikkontakten.
Aviso
Anexe o RPS Cisco (modelo PWR300-AC-RPS) apenas ao
receptáculo RPS.
Aviso:
Sólo conecte el Cisco RPS (modelo PWR300-AC-RPS) al
receptáculo RPS.
Varning!
Koppla endast Ciscos RPS (modell PWR300-AC-RPS) till
RPS-uttaget.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-3
Appendix C
Translated Safety Warnings
Service Personnel Warning
Service Personnel Warning
Warning
This equipment is to be installed and maintained by service
personnel only as defined by AS/NZS 3260 Clause 1.2.14.3 Service
Personnel.
Waarschuwing
Deze apparatuur mag slechts geïnstalleerd en onderhouden
worden door servicepersoneel conform de definitie van AS/NZS
3260 Clausule 1.2.14.3 Service Personnel.
Varoitus
Tämän laitteen saa asentaa tai huoltaa ainoastaan Australiassa
ja Uudessa Seelannissa sovellettavan AS/NZS 3260 -standardin
kohdan 1.2.14.3 Service Personnel määrittelemä
huoltohenkilöstö.
Attention
Cet équipement ne doit être installé et entretenu que par du
personnel d’entretien comme défini par la réglementation
AS/NZS 3260 Clause 1.2.14.3 Service Personnel.
Warnung
Dieses Gerät darf nur von Wartungspersonal gemäß
AS/NZS-Definition 3260, Paragraph 1.2.14.3, "Service Personnel",
installiert und gewartet werden.
Avvertenza
Questo apparecchio deve essere installato e mantenuto in
efficienza esclusivamente da personale tecnico che soddisfi i
requisiti specificati nella sezione 1.2.14.3 sul ‘Service Personnel’
contenuta nelle norme AS/NZS 3260.
Advarsel
Installasjon og vedlikehold av dette utstyret skal kun foretas av
vedlikeholdspersonell som definert i AS/NZS 3260, klausul
1.2.14.3 Service Personnel.
Aviso
Este equipamento deverá ser instalado e reparado apenas por
pessoal de manutenção qualificado, conforme estipulado em
AS/NZS 3260 Cláusula 1.2.14.3 Service Personnel.
Catalyst 3500 Series XL Hardware Installation Guide
C-4
78-6456-03
Appendix C
Translated Safety Warnings
Service Personnel Warning
Advertencia
Este equipo se debe instalar y mantener solamente por personal
de servicio, según definido por AS/NZS 3260 Cláusula 1.2.14.3
Service Personnel.
Varning!
Installation och underhåll av denna utrustning får endast utföras
av servicepersonal enligt definition i AS/NZS 3260 klausul
1.2.14.3 Service Personnel.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-5
Appendix C
Translated Safety Warnings
Qualified Personnel Warning
Qualified Personnel Warning
Warning
Waarschuwing
Varoitus
Avertissement
Achtung
Only trained and qualified personnel should be allowed to install
or replace this equipment
Installatie en reparaties mogen uitsluitend door getraind en
bevoegd personeel uitgevoerd worden.
Ainoastaan koulutettu ja pätevä henkilökunta saa asentaa tai
vaihtaa tämän laitteen.
Tout installation ou remplacement de l'appareil doit être réalisé
par du personnel qualifié et compétent.
Gerät nur von geschultem, qualifiziertem Personal installieren
oder auswechseln lassen.
Avvertenza
Solo personale addestrato e qualificato deve essere autorizzato
ad installare o sostituire questo apparecchio.
Advarsel
Kun kvalifisert personell med riktig opplæring bør montere eller
bytte ut dette utstyret.
Aviso
Este equipamento deverá ser instalado ou substituído apenas por
pessoal devidamente treinado e qualificado.
¡Atención!
Estos equipos deben ser instalados y reemplazados
exclusivamente por personal técnico adecuadamente preparado
y capacitado.
Varning
Denna utrustning ska endast installeras och bytas ut av utbildad
och kvalificerad personal.
Catalyst 3500 Series XL Hardware Installation Guide
C-6
78-6456-03
Appendix C
Translated Safety Warnings
Installation Warning
Installation Warning
Warning
Read the installation instructions before you connect the system
to its power source.
Waarschuwing
Raadpleeg de installatie-aanwijzingen voordat u het systeem met
de voeding verbindt.
Varoitus
Lue asennusohjeet ennen järjestelmän yhdistämistä
virtalähteeseen.
Attention
Avant de brancher le système sur la source d'alimentation,
consulter les directives d'installation.
Warnung
Lesen Sie die Installationsanweisungen, bevor Sie das System an
die Stromquelle anschließen.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Consultare le istruzioni di installazione prima di collegare il
sistema all’alimentatore.
Les installasjonsinstruksjonene før systemet kobles til
strømkilden.
Leia as instruções de instalação antes de ligar o sistema à sua
fonte de energia.
Ver las instrucciones de instalación antes de conectar el sistema
a la red de alimentación.
Läs installationsanvisningarna innan du kopplar systemet till
dess strömförsörjningsenhet.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-7
Appendix C
Translated Safety Warnings
Jewelry Removal Warning
Jewelry Removal Warning
Warning
Before working on equipment that is connected to power lines,
remove jewelry (including rings, necklaces, and watches). Metal
objects will heat up when connected to power and ground and
can cause serious burns or weld the metal object to the
terminals.
Waarschuwing
Alvorens aan apparatuur te werken die met elektrische leidingen
is verbonden, sieraden (inclusief ringen, kettingen en horloges)
verwijderen. Metalen voorwerpen worden warm wanneer ze met
stroom en aarde zijn verbonden, en kunnen ernstige brandwonden
veroorzaken of het metalen voorwerp aan de aansluitklemmen
lassen.
Varoitus
Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden
parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot
mukaan lukien). Metalliesineet kuumenevat, kun ne ovat
yhteydessä sähkövirran ja maan kanssa, ja ne voivat aiheuttaa
vakavia palovammoja tai hitsata metalliesineet kiinni
liitäntänapoihin.
Attention
Avant d’accéder à cet équipement connecté aux lignes
électriques, ôter tout bijou (anneaux, colliers et montres compris).
Lorsqu’ils sont branchés à l’alimentation et reliés à la terre, les
objets métalliques chauffent, ce qui peut provoquer des blessures
graves ou souder l’objet métallique aux bornes.
Warnung
Vor der Arbeit an Geräten, die an das Netz angeschlossen sind,
jeglichen Schmuck (einschließlich Ringe, Ketten und Uhren)
abnehmen. Metallgegenstände erhitzen sich, wenn sie an das
Netz und die Erde angeschlossen werden, und können schwere
Verbrennungen verursachen oder an die Anschlußklemmen
angeschweißt werden.
Catalyst 3500 Series XL Hardware Installation Guide
C-8
78-6456-03
Appendix C
Translated Safety Warnings
Jewelry Removal Warning
Avvertenza
Prima di intervenire su apparecchiature collegate alle linee di
alimentazione, togliersi qualsiasi monile (inclusi anelli, collane,
braccialetti ed orologi). Gli oggetti metallici si riscaldano quando
sono collegati tra punti di alimentazione e massa: possono
causare ustioni gravi oppure il metallo può saldarsi ai terminali.
Advarsel
Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du
skal arbeide på utstyr som er koblet til kraftledninger.
Metallgjenstander som er koblet til kraftledninger og jord blir
svært varme og kan forårsake alvorlige brannskader eller smelte
fast til polene.
Aviso
Antes de trabalhar em equipamento que esteja ligado a linhas de
corrente, retire todas as jóias que estiver a usar (incluindo anéis,
fios e relógios). Os objectos metálicos aquecerão em contacto
com a corrente e em contacto com a ligação à terra, podendo
causar queimaduras graves ou ficarem soldados aos terminais.
¡Advertencia!
Antes de operar sobre equipos conectados a líneas de
alimentación, quitarse las joyas (incluidos anillos, collares y
relojes). Los objetos de metal se calientan cuando se conectan a
la alimentación y a tierra, lo que puede ocasionar quemaduras
graves o que los objetos metálicos queden soldados a los bornes.
Varning!
Tag av alla smycken (inklusive ringar, halsband och armbandsur)
innan du arbetar på utrustning som är kopplad till kraftledningar.
Metallobjekt hettas upp när de kopplas ihop med ström och jord
och kan förorsaka allvarliga brännskador; metallobjekt kan också
sammansvetsas med kontakterna.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-9
Appendix C
Translated Safety Warnings
Stacking the Chassis Warning
Stacking the Chassis Warning
Warning
Waarschuwing
Varoitus
Do not stack the chassis on any other equipment. If the chassis
falls, it can cause severe bodily injury and equipment damage.
Het chassis mag niet op andere apparatuur gestapeld te worden.
Als het chassis mocht vallen, kan dit ernstig lichamelijk letsel en
beschadiging van de apparatuur veroorzaken.
Älä aseta asennuspohjaa minkään muun laitteen päälle.
Asennuspohja voi pudotessaan aiheuttaa vaikean
ruumiinvamman tai laitevaurion.
Avertissement
Ne placez pas ce châssis sur un autre appareil. En cas de chute,
il pourrait provoquer de graves blessures corporelles et
d'importants dommages.
Achtung
Das Gehäuse nicht auf andere Geräte stellen. Wenn das Gehäuse
herunterfällt, besteht Gefahr schwerer Personenverletzungen
und Geräteschäden.
Avvertenza
Advarsel
Aviso
Non collocare lo chassis su nessun altro apparecchio. Se lo
chassis cade, può causare lesioni gravi e danni alle
apparecchiature.
Stable ikke kabinettet oppå annet utstyr. Hvis kabinettet faller,
kan det forårsake alvorlig skade på mennesker og utstyr.
Não coloque o chassis em cima de qualquer outro equipamento.
Se o chassis cair, poderá causar ferimentos graves e danos no
equipamento.
Catalyst 3500 Series XL Hardware Installation Guide
C-10
78-6456-03
Appendix C
Translated Safety Warnings
Stacking the Chassis Warning
¡Atención!
Varning
No apilar los chasis sobre ningún otro equipo. Si el chasis se cae
al suelo puede causar graves lesiones físicas y daños al equipo.
Placera inte chassit ovanpå annan utrustning. Om chassit faller
kan allvarlig kroppsskada såväl som skada på utrustningen
uppstå.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-11
Appendix C
Translated Safety Warnings
Main Disconnecting Device
Main Disconnecting Device
Warning
Waarschuwing
Varoitus
The plug-socket combination must be accessible at all times
because it serves as the main disconnecting device.
De combinatie van de stekker en het elektrisch contactpunt moet
te allen tijde toegankelijk zijn omdat deze het hoofdmechanisme
vormt voor verbreking van de aansluiting.
Pistoke/liitinkohta toimii pääkatkaisumekanismina. Pääsy
siihen on pidettävä aina esteettömänä.
Attention
La combinaison de prise de courant doit être accessible à tout
moment parce qu'elle fait office de système principal de
déconnexion.
Warnung
Der Netzkabelanschluß am Gerät muß jederzeit zugänglich sein,
weil er als primäre Ausschaltvorrichtung dient.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Il gruppo spina-presa deve essere sempre accessibile, poiché
viene utilizzato come dispositivo di scollegamento principale.
Kombinasjonen støpsel/uttak må alltid være tilgjengelig
ettersom den fungerer som hovedfrakoplingsenhet.
A combinação ficha-tomada deverá ser sempre acessível,
porque funciona como interruptor principal.
El conjunto de clavija y toma ha de encontrarse siempre
accesible ya que hace las veces de dispositivo de desconexión
principal.
Man måste alltid kunna komma åt stickproppen i uttaget,
eftersom denna koppling utgör den huvudsakliga
frånkopplingsanordningen.
Catalyst 3500 Series XL Hardware Installation Guide
C-12
78-6456-03
Appendix C
Translated Safety Warnings
Overtemperature Warning
Overtemperature Warning
Warning
To prevent the switch from overheating, do not operate it in an
area that exceeds the maximum recommended ambient
temperature of 104°F (40°C). To prevent airflow restriction, allow
at least 3 inches (7.6 cm) of clearance around the ventilation
openings.
Waarschuwing
Om oververhitting van de schakelaar te voorkomen, mag u die niet
bedienen in een ruimte die de maximale aanbevolen
omgevingstemperatuur van 104 F (40°C) overschrijdt. Om
beperking van de luchtstroom te voorkomen, dient u ten minste 3
inch (7,6 cm) speling te laten rondom de ventilatie-openingen.
Varoitus
Estääksesi kytkimen ylikuumenemisen älä käytä sitä sellaisissa
paikoissa, joiden lämpötila ylittää ympäristön
enimmäislämpötilaksi suositellun 40°C. Jätä vähintään 7,6 cm:n
vapaa tila tuuletusaukkojen ympärille, jotta ilma pääsee vapaasti
virtaamaan.
Attention
Pour éviter une surchauffe du commutateur, ne pas le faire
fonctionner dans un local dont la température ambiante dépasse
le maximum recommandé de 40°C (104 F). Pour faciliter la
circulation d'air, aménager un dégagement d'au moins 7,6 cm
(3 pouces) autour des bouches d'aération.
Warnung
Um eine Überhitzung des Schalters zu vermeiden, ist das System
nicht in einem Bereich zu betreiben, in dem die empfohlene
Höchsttemperatur von 40°C überschritten wird. Damit der Luftfluß
nicht behindert wird, ist ein Freiraum von mindestens 7,6 cm um
die Belüftungsöffnungen herum einzuhalten.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-13
Appendix C
Translated Safety Warnings
Overtemperature Warning
Avvertenza
Per evitare il surriscaldamento dell’interruttore, non usare
l'apparecchiatura in un’area che supera la temperatura
ambientale minima consigliata di 40°C. Per evitare una
limitazione del flusso dell’aria, lasciare come minimo uno spazio
libero di 7,6 cm intorno alle aperture di ventilazione.
Advarsel
For å unngå at bryteren overopphetes skal utstyret ikke brukes på
steder hvor anbefalt maks omgivelsestemperatur overstiger 104
grader Farenheit (40°C). La det være minst 3 tommer (7,6 cm)
klaring rundt ventilasjonsåpningene for at luftsirkulasjonen skal
være uhindret.
Aviso
Para evitar sobreaquecimento do interruptor, não utilize o
equipamento numa àrea que exceda uma temperatura máxima de
40°C. Para evitar o bloqueamento da circulação de ar, deixe pelo
menos um espaço de 7.6 cm em volta das aberturas de ventilação.
¡Advertencia!
Varning!
Para evitar que el interruptor se recaliente, no se debe usar en
áreas cuya temperatura ambiente exceda la máxima
recomendada, esto es, 40°C (104°F). Para no entorpecer la
corriente de aire, dejar por lo menos 7,6 cm (3 pulgadas) de
espacio muerto alrededor de la rejilla de ventilación.
För att undvika överhettning av strömbrytaren skall den inte
användas i utrymme vars temperatur överskrider den maximalt
rekommenderade omgivningstemperaturen 40°C. Kontrollera att
det finns minst 7,6 cm fritt utrymme runt ventilationsöppningarna
så att luftflödet inte begränsas.
Catalyst 3500 Series XL Hardware Installation Guide
C-14
78-6456-03
Appendix C
Translated Safety Warnings
TN Power Warning
TN Power Warning
Warning
Waarschuwing
The device is designed to work with TN power systems.
Het apparaat is ontworpen om te functioneren met TN
energiesystemen.
Varoitus
Koje on suunniteltu toimimaan TN-sähkövoimajärjestelmien
yhteydessä.
Attention
Ce dispositif a été conçu pour fonctionner avec des systèmes
d'alimentation TN.
Warnung
Das Gerät ist für die Verwendung mit TN-Stromsystemen
ausgelegt.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Il dispositivo è stato progettato per l’uso con sistemi di
alimentazione TN.
Utstyret er utfomet til bruk med TN-strømsystemer.
O dispositivo foi criado para operar com sistemas de corrente TN.
El equipo está diseñado para trabajar con sistemas de
alimentación tipo TN.
Enheten är konstruerad för användning tillsammans med
elkraftssystem av TN-typ.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-15
Appendix C
Translated Safety Warnings
Ground Connection Warning
Ground Connection Warning
Warning
Waarschuwing
Varoitus
When installing the unit, the ground connection must always be
made first and disconnected last.
Bij de installatie van het toestel moet de aardverbinding altijd
het eerste worden gemaakt en het laatste worden losgemaakt.
Laitetta asennettaessa on maahan yhdistäminen aina tehtävä
ensiksi ja maadoituksen irti kytkeminen viimeiseksi.
Attention
Lors de l’installation de l’appareil, la mise à la terre doit toujours
être connectée en premier et déconnectée en dernier.
Warnung
Der Erdanschluß muß bei der Installation der Einheit immer
zuerst hergestellt und zuletzt abgetrennt werden.
Avvertenza
In fase di installazione dell'unità, eseguire sempre per primo il
collegamento a massa e disconnetterlo per ultimo.
Advarsel
Når enheten installeres, må jordledningen alltid tilkobles først
og frakobles sist.
Aviso
¡Advertencia!
Varning!
Ao instalar a unidade, a ligação à terra deverá ser sempre a
primeira a ser ligada, e a última a ser desligada.
Al instalar el equipo, conectar la tierra la primera y
desconectarla la última.
Vid installation av enheten måste jordledningen alltid anslutas
först och kopplas bort sist.
Catalyst 3500 Series XL Hardware Installation Guide
C-16
78-6456-03
Appendix C
Translated Safety Warnings
Circuit Breaker (15A) Warning
Circuit Breaker (15A) Warning
Warning
This product relies on the building’s installation for short-circuit
(overcurrent) protection. Ensure that a fuse or circuit breaker no
larger than 120 VAC, 15A U.S. (240 VAC, 16A international) is used
on the phase conductors (all current-carrying conductors).
Waarschuwing
Dit produkt is afhankelijk van de installatie van het gebouw voor
kortsluit- (overstroom)beveiliging. Controleer of er een zekering
of stroomverbreker van niet meer dan 120 Volt wisselstroom, 15 A
voor de V.S. (240 Volt wisselstroom, 16 A internationaal) gebruikt
wordt op de fasegeleiders (alle geleiders die stroom voeren).
Varoitus
Tämä tuote on riippuvainen rakennukseen asennetusta
oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, että
vaihevirtajohtimissa (kaikissa virroitetuissa johtimissa)
käytetään Yhdysvalloissa alle 120 voltin, 15 ampeerin ja monissa
muissa maissa 240 voltin, 16 ampeerin sulaketta tai
suojakytkintä.
Attention
Pour ce qui est de la protection contre les courts-circuits
(surtension), ce produit dépend de l'installation électrique du
local. Vérifier qu'un fusible ou qu'un disjoncteur de 120 V alt.,
15 A U.S. maximum (240 V alt., 16 A international) est utilisé sur
les conducteurs de phase (conducteurs de charge).
Warnung
Dieses Produkt ist darauf angewiesen, daß im Gebäude ein
Kurzschluß- bzw. Überstromschutz installiert ist. Stellen Sie
sicher, daß eine Sicherung oder ein Unterbrecher von nicht mehr
als 240 V Wechselstrom, 16 A (bzw. in den USA 120 V
Wechselstrom, 15 A) an den Phasenleitern (allen stromführenden
Leitern) verwendet wird.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-17
Appendix C
Translated Safety Warnings
Circuit Breaker (15A) Warning
Avvertenza
Questo prodotto dipende dall’installazione dell’edificio per
quanto riguarda la protezione contro cortocircuiti
(sovracorrente). Verificare che un fusibile o interruttore
automatico, non superiore a 120 VCA, 15 A U.S. (240 VCA, 16 A
internazionale) sia stato usato nei fili di fase (tutti i conduttori
portatori di corrente).
Advarsel
Dette produktet er avhengig av bygningens installasjoner av
kortslutningsbeskyttelse (overstrøm). Kontroller at det brukes en
sikring eller strømbryter som ikke er større enn 120 VAC, 15 A
(USA) (240 VAC, 16 A internasjonalt) på faselederne (alle
strømførende ledere).
Aviso
Este produto depende das instalações existentes para protecção
contra curto-circuito (sobrecarga). Assegure-se de que um
fusível ou disjuntor não superior a 240 VAC, 16A é utilizado nos
condutores de fase (todos os condutores de transporte de
corrente).
¡Advertencia!
Este equipo utiliza el sistema de protección contra
cortocircuitos (o sobrecorrientes) deló propio edificio.
Asegurarse de que se utiliza un fusible o interruptor automático
de no más de 240 voltios en corriente alterna (VAC), 16 amperios
del estándar internacional (120 VAC, 15 amperios del estándar
USA) en los hilos de fase (todos aquéllos portadores de
corriente).
Varning!
Denna produkt är beroende av i byggnaden installerat
kortslutningsskydd (överströmsskydd). Kontrollera att säkring
eller överspänningsskydd används på fasledarna (samtliga
strömförande ledare) för internationellt bruk max. 240 V
växelström, 16 A (i USA max. 120 V växelström, 15 A).
Catalyst 3500 Series XL Hardware Installation Guide
C-18
78-6456-03
Appendix C
Translated Safety Warnings
Grounded Equipment Warning
Grounded Equipment Warning
Warning
This equipment is intended to be grounded. Ensure that the host
is connected to earth ground during normal use.
Waarschuwing
Deze apparatuur hoort geaard te worden Zorg dat de
host-computer tijdens normaal gebruik met aarde is verbonden.
Varoitus
Tämä laitteisto on tarkoitettu maadoitettavaksi. Varmista, että
isäntälaite on yhdistetty maahan normaalikäytön aikana.
Attention
Cet équipement doit être relié à la terre. S’assurer que l’appareil
hôte est relié à la terre lors de l’utilisation normale.
Warnung
Dieses Gerät muß geerdet werden. Stellen Sie sicher, daß das
Host-Gerät während des normalen Betriebs an Erde gelegt ist.
Avvertenza
Questa apparecchiatura deve essere collegata a massa.
Accertarsi che il dispositivo host sia collegato alla massa di
terra durante il normale utilizzo.
Advarsel
Dette utstyret skal jordes. Forviss deg om vertsterminalen er
jordet ved normalt bruk.
Aviso
Este equipamento deverá estar ligado à terra. Certifique-se que o
host se encontra ligado à terra durante a sua utilização normal.
¡Advertencia!
Este equipo debe conectarse a tierra. Asegurarse de que el
equipo principal esté conectado a tierra durante el uso normal.
Varning!
Denna utrustning är avsedd att jordas. Se till att värdenheten är
jordad vid normal användning.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-19
Appendix C
Translated Safety Warnings
Supply Circuit Warning
Supply Circuit Warning
Warning
Waarschuwing
Care must be given to connecting units to the supply circuit so
that wiring is not overloaded.
Let erop dat de toestellen op voedingscircuits worden
aangesloten zonder het vermogen van de bedrading te
overschrijden.
Varoitus
Laiteyksiköt on yhdistettävä huolellisesti syöttöpiiriin niin, että
johdot eivät ole ylikuormitettuja.
Avertissement
Veillez à bien connecter les unités au circuit d'alimentation afin
de ne pas surcharger les connections.
Achtung
Avvertenza
Advarsel
Aviso
¡Atención!
Varning
Beim Anschließen der Geräte an das Stromnetz ist darauf zu
achten, daß die Schaltverbindungen nicht überlastet werden.
Fare attenzione quando si collegano le unità al circuito di
alimentazione, per non sovraccaricare i cablaggi.
Vær nøye med å koble enheter til strømforsyningskretsen slik at
ledningene ikke overbelastes.
Deverá ter precaução ao ligar unidades ao circuito de
fornecimento de energia, para não sobrecarregar a instalação.
Poner mucho cuidado al conectar los equipos al circuito de
alimentación a fin de no sobrecargar el cableado.
Var noga vid anslutning av enheter till matarströmkretsen så att
ledningarna inte överbelastas.
Catalyst 3500 Series XL Hardware Installation Guide
C-20
78-6456-03
Appendix C
Translated Safety Warnings
No On/Off Switch Warning
No On/Off Switch Warning
Warning
Unplug the power cord before you work on a system that does not
have an on/off switch.
Waarschuwing
Voordat u aan een systeem werkt dat geen aan/uit schakelaar
heeft, dient u de stekker van het netsnoer uit het stopcontact te
halen.
Varoitus
Ennen kuin teet mitään sellaiselle järjestelmälle, jossa ei ole
kaksiasentokytkintä, kytke irti virtajohto.
Attention
Avant de travailler sur un système non équipé d'un commutateur
marche-arrêt, débrancher le cordon d'alimentation.
Warnung
Bevor Sie an einem System ohne Ein/Aus-Schalter arbeiten,
ziehen Sie das Netzkabel heraus.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Prima di lavorare su un sistema che non è dotato di un
interruttore on/off, scollegare il cavo di alimentazione.
Før det skal utføres arbeid på et system som ikke har en
av/på-bryter, skal strømledningen trekkes ut.
Antes de começar a trabalhar num sistema que não possua um
interruptor ON/OFF, desligue o cabo de alimentação.
Antes de trabajar sobre cualquier sistema que carezca de
interruptor de Encendido/Apagado (ON/OFF), desenchufar el
cable de alimentación.
Dra ur nätsladden innan du utför arbete på ett system utan
strömbrytare.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-21
Appendix C
Translated Safety Warnings
Power Supply Warning
Power Supply Warning
Warning
Do not touch the power supply when the power cord is
connected. For systems with a power switch, line voltages are
present within the power supply even when the power switch is
off and the power cord is connected. For systems without a power
switch, line voltages are present within the power supply when
the power cord is connected.
Waarschuwing
U dient de voeding niet aan te raken zolang het netsnoer
aangesloten is. Bij systemen met een stroomschakelaar zijn er
lijnspanningen aanwezig in de voeding, zelfs wanneer de
stroomschakelaar uitgeschakeld is en het netsnoer aangesloten
is. Bij systemen zonder een stroomschakelaar zijn er
lijnspanningen aanwezig in de voeding wanneer het netsnoer
aangesloten is.
Varoitus
Älä kosketa virtalähdettä virtajohdon ollessa kytkettynä.
Virrankatkaisimella varustetuissa järjestelmissä on virtalähteen
sisällä jäljellä verkkojännite, vaikka virrankatkaisin on
katkaistu-asennossa virtajohdon ollessa kytkettynä.
Järjestelmissä, joissa ei ole virrankatkaisinta, on virtalähteen
sisällä verkkojännite, kun virtajohto on kytkettynä.
Attention
Ne pas toucher le bloc d'alimentation quand le cordon
d'alimentation est branché. Avec les systèmes munis d'un
commutateur marche-arrêt, des tensions de ligne sont présentes
dans l'alimentation quand le cordon est branché, même si le
commutateur est à l'arrêt. Avec les systèmes sans commutateur
marche-arrêt, l'alimentation est sous tension quand le cordon
d'alimentation est branché.
Catalyst 3500 Series XL Hardware Installation Guide
C-22
78-6456-03
Appendix C
Translated Safety Warnings
Power Supply Warning
Warnung
Berühren Sie das Netzgerät nicht, wenn das Netzkabel
angeschlossen ist. Bei Systemen mit Netzschalter liegen
Leitungsspannungen im Netzgerät vor, wenn das Netzkabel
angeschlossen ist, auch wenn das System ausgeschaltet ist. Bei
Systemen ohne Netzschalter liegen Leitungsspannungen im
Netzgerät vor, wenn das Netzkabel angeschlossen ist.
Avvertenza
Non toccare l’alimentatore se il cavo dell’alimentazione è
collegato. Per i sistemi con un interruttore di alimentazione,
tensioni di linea sono presenti all’interno dell’alimentatore
anche quando l’interruttore di alimentazione è en posizione di
disattivazione (off), se il cavo dell’alimentazione è collegato. Per
i sistemi senza un interruttore, tensioni di linea sono presenti
all’interno dell’alimentatore quando il cavo di alimentazione è
collegato.
Advarsel
Aviso
Berør ikke strømforsyningsenheten når strømledningen er
tilkoblet. I systemer som har en strømbryter, er det spenning i
strømforsyningsenheten selv om strømbryteren er slått av og
strømledningen er tilkoblet. Når det gjelder systemer uten en
strømbryter, er det spenning i strømforsyningsenheten når
strømledingen er tilkoblet.
Não toque na unidade abastecedora de energia quando o cabo de
alimentação estiver ligado. Em sistemas com interruptor, a
corrente eléctrica estará presente na unidade abastecedora,
sempre que o cabo de alimentação de energia estiver ligado,
mesmo quando o interruptor se encontrar desligado. Para
sistemas sem interruptor, a tensão eléctrica dentro da unidade
abastecedora só estará presente quando o cabo de alimentação
estiver ligado.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-23
Appendix C
Translated Safety Warnings
Power Supply Warning
¡Advertencia!
Varning!
No tocar la fuente de alimentación mientras el cable esté
enchufado. En sistemas con interruptor de alimentación, hay
voltajes de línea dentro de la fuente, incluso cuando el
interruptor esté en Apagado (OFF) y el cable de alimentación
enchufado. En sistemas sin interruptor de alimentación, hay
voltajes de línea en la fuente cuando el cable está enchufado.
Vidrör inte strömförsörjningsenheten när nätsladden är ansluten.
För system med strömbrytare finns det nätspänning i
strömförsörjningsenheten även när strömmen har slagits av men
nätsladden är ansluten. För system utan strömbrytare finns det
nätspänning i strömförsörjningsenheten när nätsladden är
ansluten.
Catalyst 3500 Series XL Hardware Installation Guide
C-24
78-6456-03
Appendix C
Translated Safety Warnings
Lightning Activity Warning
Lightning Activity Warning
Warning
Do not work on the system or connect or disconnect cables during
periods of lightning activity.
Waarschuwing
Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het
systeem te werken of kabels aan te sluiten of te ontkoppelen.
Varoitus
Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota
kaapeleita ukkosilmalla.
Attention
Ne pas travailler sur le système ni brancher ou débrancher les
câbles pendant un orage.
Warnung
Arbeiten Sie nicht am System und schließen Sie keine Kabel an
bzw. trennen Sie keine ab, wenn es gewittert.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Non lavorare sul sistema o collegare oppure scollegare i cavi
durante un temporale con fulmini.
Utfør aldri arbeid på systemet, eller koble kabler til eller fra
systemet når det tordner eller lyner.
Não trabalhe no sistema ou ligue e desligue cabos durante
períodos de mau tempo (trovoada).
No operar el sistema ni conectar o desconectar cables durante el
transcurso de descargas eléctricas en la atmósfera.
Vid åska skall du aldrig utföra arbete på systemet eller ansluta
eller koppla loss kablar.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-25
Appendix C
Translated Safety Warnings
Product Disposal Warning
Product Disposal Warning
Warning
Waarschuwing
Varoitus
Ultimate disposal of this product should be handled according to
all national laws and regulations.
Het uiteindelijke wegruimen van dit product dient te geschieden
in overeenstemming met alle nationale wetten en reglementen.
Tämä tuote on hävitettävä kansallisten lakien ja määräysten
mukaisesti.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement
soumis à des lois et/ou directives de respect de l'environnement.
Renseignez-vous auprès de l'organisme compétent.
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen
und Gesetzen des Landes erfolgen.
Avvertenza
Lo smaltimento di questo prodotto deve essere eseguito secondo
le leggi e regolazioni locali.
Advarsel
Endelig kassering av dette produktet skal være i henhold til alle
relevante nasjonale lover og bestemmelser.
Aviso
¡Advertencia!
Varning!
Deitar fora este produto em conformidade com todas as leis e
regulamentos nacionais.
Al deshacerse por completo de este producto debe seguir todas
las leyes y reglamentos nacionales.
Vid deponering hanteras produkten enligt gällande lagar och
bestämmelser.
Catalyst 3500 Series XL Hardware Installation Guide
C-26
78-6456-03
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
Chassis Warning—Rack-Mounting and Servicing
Warning
Waarschuwing
To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system
remains stable. The following guidelines are provided to ensure
your safety:
•
This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
•
When mounting this unit in a partially filled rack, load the rack from the
bottom to the top with the heaviest component at the bottom of the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
Om lichamelijk letsel te voorkomen wanneer u dit toestel in een
rek monteert of het daar een servicebeurt geeft, moet u speciale
voorzorgsmaatregelen nemen om ervoor te zorgen dat het toestel
stabiel blijft. De onderstaande richtlijnen worden verstrekt om uw
veiligheid te verzekeren:
•
Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het
enige in het rek is.
•
Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek
van onderen naar boven te laden met het zwaarste onderdeel onderaan in het
rek.
•
Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de
stabilisatoren te monteren voordat u het toestel in het rek monteert of het daar
een servicebeurt geeft.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-27
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
Varoitus
Attention
Kun laite asetetaan telineeseen tai huolletaan sen ollessa
telineessä, on noudatettava erityisiä varotoimia järjestelmän
vakavuuden säilyttämiseksi, jotta vältytään loukkaantumiselta.
Noudata seuraavia turvallisuusohjeita:
•
Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan.
•
Jos laite asetetaan osaksi täytettyyn telineeseen, aloita kuormittaminen sen
alaosasta kaikkein raskaimmalla esineellä ja siirry sitten sen yläosaan.
•
Jos telinettä varten on vakaimet, asenna ne ennen laitteen asettamista
telineeseen tai sen huoltamista siinä.
Pour éviter toute blessure corporelle pendant les opérations de
montage ou de réparation de cette unité en casier, il convient de
prendre des précautions spéciales afin de maintenir la stabilité
du système. Les directives ci-dessous sont destinées à assurer la
protection du personnel :
•
Si cette unité constitue la seule unité montée en casier, elle doit être placée
dans le bas.
•
Si cette unité est montée dans un casier partiellement rempli, charger le
casier de bas en haut en plaçant l'élément le plus lourd dans le bas.
•
Si le casier est équipé de dispositifs stabilisateurs, installer les stabilisateurs
avant de monter ou de réparer l'unité en casier.
Catalyst 3500 Series XL Hardware Installation Guide
C-28
78-6456-03
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
Warnung
Avvertenza
Zur Vermeidung von Körperverletzung beim Anbringen oder
Warten dieser Einheit in einem Gestell müssen Sie besondere
Vorkehrungen treffen, um sicherzustellen, daß das System stabil
bleibt. Die folgenden Richtlinien sollen zur Gewährleistung Ihrer
Sicherheit dienen:
•
Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell
angebracht werden.
•
Bei Anbringung dieser Einheit in einem zum Teil gefüllten Gestell ist das
Gestell von unten nach oben zu laden, wobei das schwerste Bauteil unten im
Gestell anzubringen ist.
•
Wird das Gestell mit Stabilisierungszubehör geliefert, sind zuerst die
Stabilisatoren zu installieren, bevor Sie die Einheit im Gestell anbringen oder
sie warten.
Per evitare infortuni fisici durante il montaggio o la manutenzione
di questa unità in un supporto, occorre osservare speciali
precauzioni per garantire che il sistema rimanga stabile. Le
seguenti direttive vengono fornite per garantire la sicurezza
personale:
•
Questa unità deve venire montata sul fondo del supporto, se si tratta
dell’unica unità da montare nel supporto.
•
Quando questa unità viene montata in un supporto parzialmente pieno,
caricare il supporto dal basso all’alto, con il componente più pesante
sistemato sul fondo del supporto.
•
Se il supporto è dotato di dispositivi stabilizzanti, installare tali dispositivi
prima di montare o di procedere alla manutenzione dell’unità nel supporto.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-29
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
Advarsel
Aviso
Unngå fysiske skader under montering eller reparasjonsarbeid på
denne enheten når den befinner seg i et kabinett. Vær nøye med at
systemet er stabilt. Følgende retningslinjer er gitt for å verne om
sikkerheten:
•
Denne enheten bør monteres nederst i kabinettet hvis dette er den eneste
enheten i kabinettet.
•
Ved montering av denne enheten i et kabinett som er delvis fylt, skal
kabinettet lastes fra bunnen og opp med den tyngste komponenten nederst i
kabinettet.
•
Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene
installeres før montering eller utføring av reparasjonsarbeid på enheten i
kabinettet.
Para se prevenir contra danos corporais ao montar ou reparar esta
unidade numa estante, deverá tomar precauções especiais para
se certificar de que o sistema possui um suporte estável. As
seguintes directrizes ajudá-lo-ão a efectuar o seu trabalho com
segurança:
•
Esta unidade deverá ser montada na parte inferior da estante, caso seja esta a
única unidade a ser montada.
•
Ao montar esta unidade numa estante parcialmente ocupada, coloque os itens
mais pesados na parte inferior da estante, arrumando-os de baixo para cima.
•
Se a estante possuir um dispositivo de estabilização, instale-o antes de
montar ou reparar a unidade.
Catalyst 3500 Series XL Hardware Installation Guide
C-30
78-6456-03
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
¡Advertencia!
Varning!
Para evitar lesiones durante el montaje de este equipo sobre un
bastidor, o posteriormente durante su mantenimiento, se debe
poner mucho cuidado en que el sistema quede bien estable. Para
garantizar su seguridad, proceda según las siguientes
instrucciones:
•
Colocar el equipo en la parte inferior del bastidor, cuando sea la única unidad
en el mismo.
•
Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado,
comenzar la instalación desde la parte inferior hacia la superior colocando el
equipo más pesado en la parte inferior.
•
Si el bastidor dispone de dispositivos estabilizadores, instalar éstos antes de
montar o proceder al mantenimiento del equipo instalado en el bastidor.
För att undvika kroppsskada när du installerar eller utför
underhållsarbete på denna enhet på en ställning måste du vidta
särskilda försiktighetsåtgärder för att försäkra dig om att systemet
står stadigt. Följande riktlinjer ges för att trygga din säkerhet:
•
Om denna enhet är den enda enheten på ställningen skall den installeras
längst ned på ställningen.
•
Om denna enhet installeras på en delvis fylld ställning skall ställningen fyllas
nedifrån och upp, med de tyngsta enheterna längst ned på ställningen.
•
Om ställningen är försedd med stabiliseringsdon skall dessa monteras fast
innan enheten installeras eller underhålls på ställningen.
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
C-31
Appendix C
Translated Safety Warnings
Chassis Warning—Rack-Mounting and Servicing
Catalyst 3500 Series XL Hardware Installation Guide
C-32
78-6456-03
I N D E X
Numerics
addresses, assigning IP 2-25
agency approvals A-3
10/100 ports 1-8
altitude A-1, A-2, A-3
cable lengths 2-5
applications (network examples) 1-28
cables and connectors B-1 to B-2
autonegotiation 1-8
connecting to 2-16
described 1-8
groupings 1-8
illustrated 1-6
1000BaseX ports 1-10
cable lengths 2-5
connecting to 2-19 to 2-21
B
bandwidth utilization 1-21, 1-22
BOOTP 2-28
brackets
See mounting brackets
connectors and cables B-2 to B-3
illustrated 1-10
19- and 24-inch racks 2-7
C
cable guide, attaching 2-12
A
cable lengths 2-5
cabling
AC power
10/100 ports B-1 to B-4
connecting to 2-15
1000BaseX ports B-2 to B-3
connector 1-25
GigaStack GBIC ports B-3
specifications A-1, A-2, A-3
pinouts B-4
adapter pinouts, terminal
See also connectors and cables
RJ-45-to-DB-25 B-7
cautions xi
RJ-45-to-DB-9 B-6
CGMP 1-3
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
1
Index
chassis warning
connection procedures 2-16 to 2-23
against stacking 2-2
connectivity problems, solving 3-3
rack-mounting, servicing C-27
connectors and cables
circuit breaker (15A) warning C-17
10/100 ports B-1 to B-2
Cisco Access Analog Trunk Gateway 1-36
1000BaseX ports B-2 to B-3
Cisco Access Digital Trunk Gateway 1-36
console port B-3 to B-7
Cisco CallManager software 1-34, 1-36
GigaStack GBICs B-3
Cisco Cluster Management Suite 1-27
power (AC and RPS) 1-25
Cisco Connection Online (CCO) xv
SC 2-20
Cisco Group Management Protocol
(CGMP) 1-3
See also ports
Cisco IP Phones 1-9, 1-34
connecting 2-17
console port 1-26, B-3
adapter pinouts
RJ-45-to-DB-25 terminal B-7
Cisco RPS 1-25
RJ-45-to-DB-9 terminal B-6
connecting to 2-15
cable B-5
LED 1-16
Cisco SoftPhone software 1-34
connecting to 2-22 to 2-23, B-5 to B-7
CiscoView 1-27
default characteristics 2-22
Cluster Builder application 1-27
conventions, document x
Cluster Management Suite 1-27
crossover cable
Cluster Manager application 1-27
connectivity problems 3-5
Cluster View application 1-27
pinout B-4
command-line interface (CLI) 1-27
configuration, default values 2-29
configuration examples, network 1-28
connecting
D
default characteristics of the console port 2-22
to 10/100 ports 2-16
default configuration 2-29 to 2-30
to 1000BaseX ports 2-19
designing your network, examples 1-28
to console port 2-16, B-3
desk mounting 2-15
to GBICs 2-19
diagnosing problems 3-3
to GigaStack GBICs 2-21
Catalyst 3500 Series XL Hardware Installation Guide
2
78-6456-03
Index
diagnostics 2-30
G
dimensions A-2
documentation
GBICs 1-10, 1-30
CD-ROM xiv
connecting to 2-19
related publications xiv
installing 1-10
supported 1-10
document conventions x
duplex LED 1-18, 1-19, 1-20
GigaStack GBIC 1-10, 1-30
cable lengths 2-5
connecting to 2-21
E
connector B-3
installing 1-10
electrical noise, avoiding 2-5
electromagnetic interference (EMI) A-3
ground connection warning C-16
EMC regulatory statements 2-4
grounded equipment warning C-19
Enterprise Edition software, switches
running 1-2
examples, network configuration 1-28
H
half-duplex 1-19, 1-20
HP OpenView 1-27
F
humidity A-1, A-2, A-3
features 1-1 to 1-3
feedback to Cisco Systems, web xvii
flooding, traffic control 2-29
I
front panel 1-6 to 1-22
IEEE 802.1p 1-3
10/100 ports 1-8
inline power 1-9, 2-16 to 2-17
1000BaseX ports 1-10
LED 1-18, 1-20
clearance 2-5
troubleshooting 3-6
LEDs 1-12 to 1-15
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
3
Index
installation
speed 1-18
guidelines 2-5
STAT 1-18
rack-mount 2-7
status 1-20
See also procedures
system 1-15
warning C-7
UTL 1-18, 1-20
Inter-Switch Link (ISL) 1-3
lightning activity warning C-25
IOS command-line interface 1-27
line power
IP address procedures 2-24
See inline power
IP setup 2-25
M
J
management features and defaults 2-29
jewelry removal warning C-8
Mode button 1-12, 1-18
Mode label (on Catalyst 3548 XL only) 1-18
models, switch 1-2
L
mounting, table or desk 2-15
LAN-to-phone jack 2-17
mounting brackets 2-7
attaching 2-9, 2-13
LEDs
Catalyst 3508G XL front panel 1-12
rack-mount 2-11
Catalyst 3512 and 3524 XL front panel 1-13
wall-mount 2-14
Catalyst 3548 XL front panel 1-15
color meanings 1-20
duplex 1-18, 1-20
N
half-duplex 1-19, 1-20
network configuration examples 1-28
interpreting 1-18
network redundancy values 2-29
LINE PWR 1-18
noise, electrical 2-5
port 1-18 to 1-22
no on/off switch warning C-21
POST results 2-15, 3-2
RPS 1-16
Catalyst 3500 Series XL Hardware Installation Guide
4
78-6456-03
Index
O
1000BaseX 1-10
See also 10/100, 1000BaseX, inline power
overtemperature warning C-13
POST
LEDs 3-2
results 2-15, 3-1, 3-2
P
power
packing list 2-6
connecting to 2-15
PC, connecting to switch 2-22
power connectors 1-23 to 1-24, 1-25
performance
power on 2-15
network design 1-28
performance problems, solving 3-3
power specifications A-1, A-2, A-3
power supply
performance tuning features 2-29
AC power outlet 1-25
personnel warning C-6
RPS connector 1-25
pinouts
warning C-22
10/100 ports B-2
procedures
adapters B-5 to B-7
connection 2-16 to 2-23
cable, straight-through and crossover B-4
installation 2-5 to 2-15
console port B-5 to B-7
IP address 2-24
RJ-45-to-DB-25 terminal adapter B-7
product disposal warning C-26
RJ-45-to-DB-9 PC adapter B-6
PSTN 1-36
RJ-45-to-DB-9 terminal adapter B-6
publications, related xiv
rollover cable B-5 to B-7
Public Switched Telephone Network
port LEDs 1-18 to 1-22
See PSTN
port modes
changing 1-12, 1-18
LEDs 1-18
See also Mode button
Q
qualified personnel warning C-6
ports
10/100 1-6
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
5
Index
software by model 1-2
R
software switch management 1-27
rack installation 2-7
bracket mounting points 2-7
rack-mounting 2-11
rear panel 1-23 to 1-24
clearance 2-5
specifications A-1
stacking the chassis warning C-10
standard edition software, switches
running 1-2
startup
powering on 2-15
Redundant Power Supply
straight-through cable pinouts B-4
See RPS
regulatory statements, EMC 2-4
SunNet Manager 1-27
RJ-45 connector, console port 2-23, B-3
supply circuit warning C-20
RJ-45 console port 1-23
switch
rollover cable 2-23, B-5, B-6
applications 1-28
RPS
startup
powering on 2-15
connecting to 2-15
connector 1-25
system LED 1-15
LED 1-16
warning C-2, C-3
T
table-mounting 2-15
S
technical specifications A-1
safety 2-2, C-1
Telnet, and accessing the CLI 1-27
SC connector 2-20, B-2 to B-3
temperature
security values 2-30
operating A-1
setup program 2-24 to 2-27
warning C-13
shelf-mounting 2-15
terminal, connecting to switch 2-22
slots
terminal emulation software 2-22
See ports 1-10
SNMP network management platforms 1-3,
1-27
TN power warning C-15
translated warnings C-1
troubleshooting 3-1 to 3-5
Catalyst 3500 Series XL Hardware Installation Guide
6
78-6456-03
Index
U
URLs, Cisco xiv
UTL LED 1-18, 1-19
V
Visual Switch Manager (VSM) 1-27
VSM 1-27
W
wall-mounting 2-13 to 2-14
warnings
defined xi
installation 2-2
translated C-1
Catalyst 3500 Series XL Hardware Installation Guide
78-6456-03
7
Index
Catalyst 3500 Series XL Hardware Installation Guide
8
78-6456-03
Download PDF