Automotive Data Solutions FLCI-HA(RS)-HA7-[CMMIXA0] Honda Odyssey 2014 Installation Guide
Automotive Data Solutions FLCI-HA(RS)-HA7-[CMMIXA0] is a remote start system designed for specific Honda and Acura vehicles. This system allows you to start your vehicle remotely using a compatible remote control, providing convenience and comfort in various situations. The system includes features for remote start, door lock/unlock, trunk release, and other vehicle control functions. It's designed for professional installation by certified technicians and requires specific accessories for functionality.
PDF
Download
Document
Advertisement
Advertisement
INSTALL GUIDE FLCI-HA(RS)-HA7-[CMMIXA0]-EN DOCUMENT NUMBER 79489 REVISION DATE 20220310 FIRMWARE FLCI-HA(RS)-HA7-[CMMIXA0] HARDWARE CMMIXA0 ACCESSORIES ADS-USB (REQUIRED) FLRF1/2/4 (REQUIRED) MYCAR (OPTIONAL) TERMS OF USE: Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 BEFORE INSTALLATION 1- Connect module to computer 2- Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately) www.idatastart.com PAGE 2 OF 19 VEHICLE LIST - 1 OF 1 DOC.: #79489 • 20220310 • • • • • • • • • • • RLX PTS AT 16-20 1 • • • • • • TLX PTS AT 15-20 1 • • • • • Fit PTS AT 15-20 1 • • • • • HR-V PTS AT 16-22 1 • • • • • Odyssey PTS AT 14-17 2 • • • • • • Passport PTS AT 19-21 1 • • • • • Pilot PTS AT 16-22 1 • • • • Ridgeline PTS AT 17-22 1 • • • • BRAKE PEDAL STATUS • 16-18 1 TACHOMETER OUTPUT 14-20 1 RDX PTS AT AUTOLIGHT CTRL MDX PTS AT HOOD STATUS OUTPUT* DOOR UNLOCK • TRUNK STATUS OUTPUT DOOR LOCK • DOOR STATUS OUTPUT DISARM OEM ALARM • TRUNK/HATCH RELEASE ARM OEM ALARM • E-BRAKE OUTPUT DATA IMMOBILIZER BYPASS • POWER SLIDING DOOR (R) INSTALL TYPE 16-22 1 POWER SLIDING DOOR (L) YEAR ILX PTS AT POWER LIFTGATE MODEL HONDA ACURA MAKE FEATURES • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • *Available only if vehicle is equipped with factory hood switch. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 3 OF 19 BOX CONTENTS - 1 OF 1 DOC.: #79489 • 20220310 BOX CONTENTS MODULE T-HARNESS 1 (Accessories sold separately) 10 PIN CONNECTOR VS2 LED 2 BLUE BLACK BLACK 2 4 6 1 3 5 2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 2 1 4 3 6 5 8 7 10 9 12 11 PROGRAMMING BUTTON LED 1 A VS1 G F B E 4 3 2 1 BLACK RF PORT/ WEBLINK PORT 4 3 2 1 BLUE TELEMATIC PORT 3 2 1 BLACK 9 10 7 8 5 6 3 4 1 2 WHITE 12 PIN CONNECTOR MS1 VS4 VS3 C D AFTERMARKET HOOD SWITCH AND CABLE WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 4 OF 19 COMPATIBLE ACCESSORIES - 1 OF 1 DOC.: #79489 • 20220310 RF KIT (accessories sold separately) FLRF1/2/4 RF KIT (NC) MODULE RF PORT ANTENNA TELEMATIC KIT (accessories sold separately) MYCAR MODULE TELEMATIC PORT VEHICLE YELLOW - HORN Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 5 OF 19 ACURA RDX PTS AT RLX PTS AT TLX PTS AT Fit PTS AT 16-18 16-20 15-20 15-20 16-22 HONDA HR-V PTS AT Passport PTS AT Pilot PTS AT 19-21 16-22 Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR 14-20 CONNECTOR NAME MDX PTS AT 16-22 DOC.: #79489 • 20220310 WIRE DESCRIPTION ILX PTS AT YEAR MODEL MAKE TYPE 1 - WIRE CHART - 1 OF 2 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, above glove box ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, above glove box ~ Lights off ~ Blue 12 pin 01 Orange (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 Gray (-) Headlamp switch ~ 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, above glove box ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, above glove box ~ Lights off ~ Blue 12 pin 01 Pink (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 Gray (-) Headlamp switch ~ 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, above gas pedal ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, above gas pedal ~ Lights off ~ Blue 12 pin 01 Tan (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 Gray (-) Headlamp switch ~ 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, near driver fuse box ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, near driver fuse box ~ Lights off ~ Blue 12 pin 01 Red (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 Pink (-) Headlamp switch ~ 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, above glove box ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, above glove box ~ Lights off ~ Blue 12 pin 01 Red (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 Pink (-) Headlamp switch ~ 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, behind instrument cluster ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, behind instrument cluster ~ Lights off ~ Blue 12 pin 01 Brown (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 Gray (-) Headlamp switch ~ 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, behind instrument cluster ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, behind instrument cluster ~ Lights off ~ Blue 12 pin 01 Brown (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 Gray (-) Headlamp switch ~ 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, above glove box ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, above glove box ~ Lights off ~ Blue 12 pin 01 Pink (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 White (-) Headlamp switch ~ 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, above glove box ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, above glove box ~ Lights off ~ Blue 12 pin 01 Pink (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 White (-) Headlamp switch ~ FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 6 OF 19 Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR 17-22 CONNECTOR NAME YEAR MODEL Ridgeline PTS AT DOC.: #79489 • 20220310 WIRE DESCRIPTION HONDA MAKE TYPE 1 - WIRE CHART - 2 OF 2 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, above glove box ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, above glove box ~ Lights off ~ Blue 12 pin 01 Pink (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 White (-) Headlamp switch ~ FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 7 OF 19 TYPE 1 - WIRING DIAGRAM - 1 OF 1 DOC.: #79489 • 20220310 SMART PCU (USE WIRE CHART) M1 M6 RF PORT/WEBLINK PORT M6 TELEMATIC PORT M5 M4 M2 M3 M1 01 02 03 04 05 06 M2 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 2 VS2 1 1: 36 PIN PTS CONNECTOR 1: 36 PIN PTS HARNESS MS2 VS1 ONLY WITH T-HARNESS MANUFACTURED AFTER 2016/03/17 VS4 2: 20 PIN IGNITION CONNECTOR 2: 20 PIN IGNITION HARNESS VS3 MS1 HEAD LAMP SWITCH LIGHTS OFF (-) - 01 PARKING LIGHT (-) - 08 3 2 1 12 11 10 9 6 5 4 8 7 M3 01 BROWN/BLACK - PARKING LIGHT (-) OUTPUT 02 GRAY - GWR (-) OUTPUT 03 EMPTY 04 EMPTY 05 EMPTY 06 PURPLE/GREEN (NC) 07 EMPTY 08 BLUE/GREEN (NC) 09 EMPTY 10 EMPTY 11 GRAY/GREEN - HORN (-) OUTPUT 12 DKGREEN/GREEN (NC) M4 01 02 03 GRAY/BLACK (NC) 04 GRAY/WHITE - HOOD STATUS (-) INPUT 05 06 07 08 09 10 HORN (-) 1 OPTIONAL 1 HOOD SWITCH 2 KEYLESS ACCESS SYSTEM FUNCTIONALITY OF THE VEHICLE'S DOOR HANDLE WILL NOT REMAIN OPERATIONAL DURING REMOTE START SEQUENCE. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 2 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 8 OF 19 Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR 14-17 CONNECTOR NAME YEAR MODEL Odyssey PTS AT DOC.: #79489 • 20220310 WIRE DESCRIPTION HONDA MAKE TYPE 2 - WIRE CHART - 1 OF 1 36 pin PTS harness ~ ~ 36 pin ~ ~ ~ Smart PCU, above gas pedal ~ 20 pin harness ~ ~ 20 pin ~ ~ ~ Smart PCU, above gas pedal ~ Lights off ~ Blue 12 pin 10 Pink (-) Headlamp switch ~ Parking light ~ Blue 12 pin 08 Gray (-) Headlamp switch ~ FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 9 OF 19 TYPE 2 - WIRING DIAGRAM - 1 OF 1 DOC.: #79489 • 20220310 SMART PCU (USE WIRE CHART) M1 M6 RF PORT/WEBLINK PORT M6 TELEMATIC PORT M5 M4 M2 M3 M1 01 02 03 04 05 06 M2 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 2 VS2 1 1: 36 PIN PTS CONNECTOR 1: 36 PIN PTS HARNESS MS2 VS1 ONLY WITH T-HARNESS MANUFACTURED AFTER 2016/03/17 VS4 2: 20 PIN IGNITION CONNECTOR 2: 20 PIN IGNITION HARNESS VS3 MS1 HEAD LAMP SWITCH PARKING LIGHT (-) - 08 LIGHTS OFF (-) - 10 3 2 1 12 11 10 9 6 5 4 8 7 M3 01 BROWN/BLACK - PARKING LIGHT (-) OUTPUT 02 GRAY - GWR (-) OUTPUT 03 EMPTY 04 EMPTY 05 EMPTY 06 PURPLE/GREEN (NC) 07 EMPTY 08 BLUE/GREEN (NC) 09 EMPTY 10 EMPTY 11 GRAY/GREEN - HORN (-) OUTPUT 12 DKGREEN/GREEN (NC) M4 01 02 03 GRAY/BLACK (NC) 04 GRAY/WHITE - HOOD STATUS (-) INPUT 05 06 07 08 09 10 HORN (-) 1 OPTIONAL 1 HOOD SWITCH 2 KEYLESS ACCESS SYSTEM FUNCTIONALITY OF THE VEHICLE'S DOOR HANDLE WILL NOT REMAIN OPERATIONAL DURING REMOTE START SEQUENCE. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 2 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com MODULE PROGRAMMING PROCEDURE (PTS) - 1 OF 1 01 Push start button once [1x] to ON position. STOP ACC ON START 07 ENGINE START STOP 02 03 STOP ACC PAGE 10 OF 19 DOC.: #79489 • 20220310 Push start button once [1x] to ON position. STOP ACC ON START ENGINE START STOP Wait, LED 1 will flash GREEN rapidly. 08 Push start button once [1x] to OFF position. 09 ON START ENGINE START STOP Wait, LED 1 will turn solid GREEN for 2 seconds. Push start button once [1x] to OFF position. STOP ACC ON START ENGINE START STOP 04 WARNING: Disconnect power last. Disconnect module from vehicle. 10 Press UNLOCK on the OEM remote. 05 Connect module to computer and proceed with extended programming. >> If the vehicle is equipped with a power liftgate: Open and close the power liftgate with the OEM keyfob. 06 Connect power first. Connect module to vehicle. 11 Module Programming Procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 01 Time restriction. Complete next step within 7 seconds. 02 OFF ACC ON START >> PAGE 11 OF 19 DOC.: #79489 • 20220310 To exit valet mode: repeat steps 1 to 5. Cycle ignition ON five times [5x OFF/ON] rapidly. ENGINE START STOP 03 04 Wait, LED 1 will turn solid RED for 2 seconds. Set ignition to OFF position. OFF ACC ON START ENGINE START STOP 05 Valet Mode Programming Procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com AFTERMARKET REMOTE PROGRAMMING - 1 OF 1 PAGE 12 OF 19 DOC.: #79489 • 20220310 AFTERMARKET REMOTE PROGRAMMING: NOTES I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 13 OF 19 MODULE NAVIGATION PROCEDURE - 1 OF 1 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13. 04 >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will flash GREEN an equal amount of times continuously. 09 01 OFF ACC ON START DOC.: #79489 • 20220310 TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid RED. 10 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will flash RED an equal amount of times continuously. 11 TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid GREEN. 12 Configure every other setting and proceed to step 13. [Z] LED 1 will flash GREEN as many times as the current (or default) setting number, continuously. 13 MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED 1 will flash RED rapidly. Release programming button. LED 1 will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will flash GREEN an equal amount of times continuously. 14 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED. [Y] LED 1 will flash RED as many times as the current option number continuously. ENGINE START STOP 02 03 [X] Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 14 OF 19 MODULE NAVIGATION CHART - 1 OF 2 I Default settings are listed in bold. 01 II Make sure the option is covered on the vehicle before attempting to change the setting. 02 03 04 DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS 05 TAKEOVER 06 N/A 07 01 [Z] SETTINGS [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES FACTORY KEYLESS RS SEQUENCE CONFIGURATION 08 09 DOC.: #79489 • 20220310 MODULE RUN TIME WAIT TO START DELAY 01 OFF 02 ON 01 OFF 02 ON 01 OFF 02 ON 01 OFF 02 ON 01 ENABLE 02 DISABLE* 01 N/A 01 DISABLE 02 N/A 03 LOCK + UNLOCK + LOCK 04 LOCK + LOCK + LOCK 01 03 MIN 02 05 MIN 03 10 MIN 04 15 MIN 05 25 MIN 06 30 MIN 07 35 MIN 08 15 MIN 01 02 SEC 02 05 SEC 03 08 SEC 04 10 SEC 05 15 SEC 06 20 SEC 07 25 SEC 08 30 SEC 10 N/A 01 N/A 11 N/A 01 N/A 12 N/A 01 N/A 13 N/A 01 N/A *Vehicle will shutdown when a door is opened. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com PAGE 15 OF 19 MODULE NAVIGATION CHART - 2 OF 2 14 01 [Z] SETTINGS [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES HORN EVENT TRIGGER CONFIGURATION 15 02-07 Technical Support only 01 DOC.: #79489 • 20220310 HORN CHIRPS WIDTH N/A 01 DOUBLE LOCK 02 LOCK + UNLOCK 03 LOCK + UNLOCK + START 04 DOUBLE LOCK + START 01 30 mSEC 02 15 mSec 03 60 mSec 01 N/A *Vehicle will shutdown when a door is opened. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES - 1 OF 1 I WARNING: The following applies only when the parking lights are connected and supported by the system. 03 Foot brake is ON. 04 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 10 N/A 11 N/A 12 N/A 13 N/A 14 N/A 15 N/A 16 CAN communication failure during RS sequence. REMOTE STARTER ERROR CODES: NOTES Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN PAGE 16 OF 19 DOC.: #79489 • 20220310 www.idatastart.com I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 DIAGNOSTIC TEST MODULE LED 1 STATUS MODULE DIAGNOSTICS - 1 OF 1 Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. FLCI-HA(RS)-HA7-[CMMIXA0]-EN PAGE 17 OF 19 DOC.: #79489 • 20220310 www.idatastart.com MODULE RESET PROCEDURE - 1 OF 1 01 Disconnect all connectors from module except the BLACK 20-PIN connector. 07 Reconnect all connectors. 02 Disconnect the BLACK 20-PIN connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module’s programming button while connecting the BLACK 20-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds. 06 Module RESET completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN PAGE 18 OF 19 DOC.: #79489 • 20220310 www.idatastart.com INSTALLATION CHECKLIST - 1 OF 1 PAGE 19 OF 19 DOC.: #79489 • 20220310 CHECKLIST 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question 1: Do the doors lock? ¨ YES: Go to next step. ¨ NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. RAP and auto light shutdown test ¨ YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 10 ¨ 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. ¨ YES: Go to next step. ¨ NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Question 2: Do the doors unlock? Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? ¨ YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 11 Open hood. ¨ 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. 13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 3: Does the trunk or hatch open/unlock? Question 9: Does the vehicle remote start? ¨ YES: Close trunk or hatch and go to next step. ¨ NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. 15 Enter vehicle and close the doors. Question 4: Does the driver side sliding door open? 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. ¨ YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. 17 Wait for the vehicle to start. ¨ NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 18 Press brake pedal. 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. ¨ YES: Go to next step. 6 ¨ YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. ¨ NO: Go to next step. 14 Close hood. Question 10: Does the vehicle shut down? Question 5: Does the passenger side sliding door open? ¨ YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. ¨ ¨ NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 20 Installation checklist completed. Question 6: Does the vehicle remote start? ¨ YES: Go to next step. ¨ NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2022 FLCI-HA(RS)-HA7-[CMMIXA0]-EN www.idatastart.com ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Remote Start
- Door Lock/Unlock
- Trunk Release
- Hood Status
- Power Door Control
Frequently asked questions
The FLCI-HA(RS)-HA7-[CMMIXA0] system requires an ADS-USB cable and an FLRF1/2/4 RF kit for basic operation. A MYCAR telematic kit is optional.
The system supports specific Honda and Acura models, including the Odyssey, Pilot, Ridgeline, RLX, TLX, Fit, HR-V, MDX, RDX and ILX. Refer to the vehicle list in the manual for specific years and models.
The aftermarket remotes must be programmed to the RF kit. Refer to the RF-Kit user guide included with your accessories for specific programming instructions.