Create Something
Extraordinary
KitchenAid Cooking
Specifications & Dimensions _
Ranges, Wall Ovens, Cooktops,
Microwaves, Warming Drawers
®
Freestanding Gas Ranges
PRODUCT DIMENSIONS
KGRS308X, KGRS208X, KGRS206X
A.36" ± 1⁄8" (91.44 cm ± .32 cm) cooktop surface height with leveling
legs screwed all the way in*
B.Model/serial rating plate (located behind the warming/
storage drawer)
C.481⁄2" (123.2 cm) max. overall height with leveling legs screwed
all the way in*
D.287⁄16" (72.2 cm) depth with handle
E.253⁄4" (65.4 cm) depth without handle
F.297⁄8" (75.9 cm) overall width
*Range can be raised approximately 3⁄4" (1.9 cm) by adjusting the leveling legs.
C
A
Anti-tip bracket:
Anti-tip bracket must be securely mounted
to subfloor and wall. Thickness of flooring
may require longer screws to anchor bracket
to subfloor. Longer screws are available
from your local hardware store.
E
F
D
B
Freestanding Dual Fuel & Gas Ranges
PRODUCT DIMENSIONS
Cabinet opening dimensions shown are for 25" (63.5 cm) countertop depth,
24" (61 cm) base cabinet depth, and 36" (91.4 cm) countertop height.
YKDRS807S, KGRS807S
30"/76.2 cm
13"/33 cm max.
For minimum
clearance to
top of cooktop,
see NOTES.
upper cabinet depth
30"/76.2 cm min.
opening width
5 / "/14.6 cm
3 4
18"/45.7 cm
41 / "/106 cm
3 4
upper cabinet
to countertop
30"/76.2 cm min.
overall height
36"/91.4 cm
cooktop height
with leveling
legs in lowest
position
opening width
5"/12.7 cm min.
Grounded outlet
clearance from both sides
of range to side wall or
other combustible material
8"/
20.3 cm
8"/
20.3 cm 7"/17.8 cm
This shaded area
recommended for installation
of rigid gas pipe.
41/2"/11.4 cm
11/2"/1.6 cm
Cabinet door or
271/4"/69.2 cm*
from handle to
standoff at back of range
countertop,
*When installed in aa 24"
24" (61
(61cm)
cm)base
basecabinet
cabinetwith
with25"
25"(63.5
(63.5cm)
cm)
countertop,
front
beyond
24"24"
(61(61
cm)cm)
base
cabinet.
frontofofoven
ovendoor
doorprotrudes
protrudes1"1"(2.54
(2.54cm)
cm)
beyond
base
cabinet.
hinge should not
cm
41/2"/11.4
Anti-tip
bracket:
Anti-tip bracket: extend into the cutout.
Anti-tip bracket
must
be
securely
Anti-tip bracket must be securely
mountedmounted
to subfloor.
Thickness
of of
to subfloor.
Thickness
flooring
may require
longer
screws
flooring may
require
longer
screws
tobracket
anchor
bracket
to subfloor.
NOTES:
24" (61
minimum
when bottom of wood or metal
to anchor
tocm)
subfloor.
Longer
screws arebyavailable
is protected
not less than 1/4" (0.635 cm) flame retardant
Longercabinet
screws
arelocal
available
from
from
your
hardware
store.
millboard covered with not less than No. 28 MSG sheet steel,
your local
hardware
0.015"
(0.038 cm)store.
stainless steel, 0.024" (0.06 cm) aluminum,
or 0.020" (0.05 cm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an unprotected wood or metal cabinet.
8
If installing a hood or microwave hood combination above the
range, follow hood or microwave hood combination installation
instructions
for dimensional
clearances
the cooking
surface.
Dimensions are for planning purposes only. For additional product
information,
refer
to the above
Installation
Instructions
KitchenAid
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
Freestanding Dual Fuel Double Oven Range
PRODUCT DIMENSIONS
KDrS505x
B*
A.353⁄4" ± 1⁄8" min. (90.8 cm ± 0.32 cm min.) cooktop height
with leveling legs screwed all the way in
B. Model/serial/rating plates (located behind the control panel)*
C.471⁄8" ± 1⁄8" min. (119.7 cm ± 0.32 cm min.) overall height
with leveling legs screwed all the way in**
D.281⁄2" ± 1⁄4" (72.4 cm ± 0.635 cm) depth with handles
E.KDRS505X: 261⁄8" ± 1⁄8" (56.2 cm ± 0.32 cm)†
F.2915⁄16" ± 1⁄16" (76 cm ± 0.16 cm) width
C**
A
D
E†
F
*Model/serial/rating plates may be rotated up from behind the
control panel for viewing from the front of the range.
**Range can be raised approximately 1" (2.54 cm) by adjusting the leveling legs.
†Excludes handles. Dimension given is from wall to front of oven doors
and will vary based on electrical outlet receptacle installation.
Anti-tip bracket:
Anti-tip bracket must be securely mounted
to subfloor or wall. Thickness of flooring
may require longer screws to anchor bracket
to subfloor. Longer screws are available
from your local hardware store.
D
B
C
A
E
F
J
K
G
I
L
H
L
81⁄2"/
21.6 cm
†
Dimensions
11⁄2"/
3.8 cm
14"/35.6 cm
21⁄4"/5.7 cm
1 ⁄4"/3.2 cm*
81⁄2"/21.6 cm**
gas line location
1
Cooking
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
KitchenAid
9
Slide-In Dual Fuel & Gas Ranges
PRODUCT DIMENSIONS
Countertop Preparation
YKDSS907S, KGSS907S, KGSK901S
30"/76.2 cm
opening
width
30"/
76.2 cm
3/8"/0.95
cm
or tiled
303/4 "/78.1 cm Formed
countertop trimmed
Cabinet opening dimensions shown are for 25" (63.5
cm)
3
/8 " (0.95countertop
cm) back atdepth,
front
24" (61 cm) base cabinet depth, and 36" (91.4 cm)corners
countertop
height.
of countertop
opening
23"/
58.4 cm
355/8"/
89.7 cm*
from notch to
the back of range
side panels
Countertop
mustcm
be level.
–
13"/33
max.Place level on countertop
For minimum
upper cabinet
first side-to-side,
then depth
front-to-back. If countertop
is tonot
clearance
top offor
cooktop,
level, range will not be level. Oven must be level
cm min.
see NOTES.
satisfactory 30"/76.2
bakingopening
conditions.
width
cooktop height
with leveling
legs in lowest
position
18"/45.7 cm
upper cabinet
to countertop
2215/16"/58.3 cm
3/4"/1.9 cm
radius both corners
opening depth
30"/76.2 cm min.
30"/
76.2 cm
27 / " /
69.2 cm**
1 4
from handle to
standoff at back of range
* Range can be raised approximately 1" (2.54 cm) by adjusting
*Range can be raised approximately 1" (2.54 cm) by adjusting the leveling legs.
the leveling legs.
**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm) countertop,
**When
installed
in a 24" (61
base
25"cm)
(63.5
cm)
front
of oven
door protrudes
1 ¾"cm)
(4.4
cm)cabinet
beyondwith
24" (61
base
cabinet.
countertop, front of oven door protrudes 13/4" (4.4 cm) beyond
24" (61 cm) base cabinet.
opening width
Anti-tip bracket:
5"/12.7 cm
min.
Anti-tip bracket:
Grounded outlet
must be securely
– KDSS907S Anti-tip bracket
Anti-tip bracket must be securely
This shaded area
to subfloor.
Thickness
KGSS907S mountedmounted
8"/ ofof
to subfloor.
Thickness
flooring
may require
longer
screwsrecommended for installation
require
longer
screws
20.3
cm
2"/5.1 cmflooring
min. may
8"/ bracket to subfloor.
of rigid gas pipe.
anchor
– KGSK901S to anchortobracket
subfloor.
20.3screws
cmto are
Longer
available
clearance fromLonger
both sides
screws
are
available
from
1
7"/17.8
cm store.
4 /2"/11.4 cm
hardware
of range to side wall or from your local
your local hardware store.
other combustible material
11/2"/3.8 cm
41/2"/11.4 cm
CUTOUT DIMENSIONS
Cabinet
opening
dimensions shown
forfor
25" 25"
(63.5(63.5
cm) countertop
depth, depth,
Cabinet
opening
dimensions
shownareare
cm) countertop
24" cm)
(61 cm)
base
cabinet depth,
depth, and
(91.4
cm) cm)
countertop
height. height.
24" (61
base
cabinet
and36"36"
(91.4
countertop
13"/33 cm max.
m*
For minimum
clearance to
top of cooktop,
see NOTES.
upper cabinet depth
ght
g
st
30"/76.2 cm min.
opening width
2215/16"/58.3 cm
18"/45.7 cm
opening depth
3/4"/1.9 cm
radius both corners
upper cabinet
to countertop
30"/76.2 cm min.
opening width
5"/12.7 cm min.
– KDSS907S
KGSS907S
2"/5.1 cm min.
Grounded outlet
This shaded area
recommended for installation
of rigid gas pipe.
NOTES: 24" (61 cm) minimum when bottom of wood or metal
cabinet is protected by not less than 1/4" (0.635 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.038 cm) stainless steel, 0.024" (0.06 cm) aluminum,
or 0.020" (0.05 cm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
NOTES:
24"and
(61thecm)
minimum
clearancewood
when
of wood
platform
bottom
of an unprotected
or bottom
metal cabinet.
or metal
cabinet is covered by not less than 1⁄4" (0.635 cm) flame
If installing a hood or microwave hood combination above the
retardant
millboard
covered
withhood
notcombination
less than No.
28 MSG
range, follow
hood or
microwave
installation
sheet
steel, 0.015"
(0.038 cm)
stainless
steel,
0.024"surface.
(0.06 cm)
instructions
for dimensional
clearances
above
the cooking
aluminum, or 0.020" (0.05 cm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an unprotected wood or metal cabinet.
If installing a hood or microwave hood combination above the
range, follow hood or microwave hood combination installation
instructions for dimensional clearances above the cooking surface.
8"/
20.3 cm
8"/
cm
7"/17.8 cm
– KGSK901S
20.3
clearance from both sides
of range to side wall or
other combustible material
Cabinet door or
hinge should not
extend into the cutout.
41/2"/11.4 cm
11/2"/3.8 cm
41/2"/11.4 cm
Cabinet door or
hinge should not
extend into the cutout.
NOTES: 24" (61 cm) minimum when bottom of wood or metal
cabinet is protected by not less than 1/4" (0.635 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.038 cm) stainless steel, 0.024" (0.06 cm) aluminum,
or 0.020" (0.05 cm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an unprotected wood or metal cabinet.
10
Dimensions
arecombination
for planning
purposes
only. For additional product information, refer to the Installation Instructions
If installing a hood or microwave
hood
above
the
KitchenAid
and/or
Use & Care
Guide packed with product. Specifications subject to change without notice.
range, follow hood or microwave hood
combination
installation
instructions for dimensional clearances above the cooking surface.
223/4"
Cooktop sides of range fit over
edges of countertop opening.
Countertop must be level. Place lev
countertop, first side-to-side; then
If countertop is not level, range wil
Oven must be level for satisfactory
Freestanding Electric Ranges
PRODUCT DIMENSIONS
YKERS308X, YKERS208X, YKERS206X
A.353⁄4" (90.8 cm) min. cooktop height with leveling legs screwed
all the way in*
B.Model/serial rating plate (located behind the warming/
storage drawer)
C.473⁄4" (121.3 cm) min. overall height with leveling legs screwed
all the way in*
D.YKERS206X: 297⁄16" (74.8 cm) depth with handle
YKERS208X, YKERS308X: 287⁄16" (72.2 cm) depth with handle
E.253⁄4" (65.4 cm) depth without handle
F.297⁄8" (75.9 cm) overall width
*Range can be raised approximately 3⁄4" (1.9 cm) by adjusting the leveling legs.
C
A
Anti-tip bracket:
Anti-tip bracket must be securely mounted
to subfloor and wall. Thickness of flooring
may require longer screws to anchor bracket
to subfloor. Longer screws are available
from your local hardware store.
E
F
D
B
PRODUCT DIMENSIONS
YKERS807S
30"/76.2 cm
53/4"/
14.6 cm
36"/91.4 cm*
413/4"/106 cm
271/4"/69.2 cm
max.
30"/76.2 cm
Anti-tip bracket:
Model/serial number
plate (located on the
right-hand side oven
door trim)
Anti-tip bracket must be securely
mounted to subfloor. Thickness of
flooring may require longer screws
to anchor bracket to subfloor.
Longer screws are available
from your local hardware store.
from handle
to standoff at
back of range
* With leveling legs lowered 11⁄2 turns.
Cabinet opening dimensions shown are for 25" (63.5 cm) countertop depth,
24" (61 cm) base cabinet depth, and 36" (914 cm) countertop height.
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
13"/33
cmtomax.
and/or Use & Care Guide packed with product. Specifications
subject
change without notice.For minimum
upper cabinet depth
30"/76.2 cm min.
opening width
clearance to
top of cooktop,
see NOTES.
KitchenAid
11
Cooking
Anti-tip bracket:
Anti-tip bracket must be securely mounted
to subfloor or wall. Thickness of flooring
may require longer screws to anchor bracket
to subfloor. Longer screws are available
from your local hardware store.
Dimensions
overall height
with leveling
legs screwed
all the way in
Freestanding Electric Double Oven Ranges
PRODUCT DIMENSIONS
YKER507X
B**
A.353⁄4" ± 1⁄8" min. (90.8 cm ± 0.32 cm min.) cooktop height
with leveling legs screwed all the way in
B. Model/serial/rating plates (located behind the control panel)*
C.471⁄8" ± 1⁄8" min. (119.7 cm ± 0.32 cm min.) overall height
with leveling legs screwed all the way in**
D.281⁄2" ± 1⁄4" (72.4 cm ± 0.635 cm) depth with handles
E.261⁄8" ± 1⁄8" (56.2 cm ± 0.32 cm)†
F.2915⁄16" ± 1⁄16" (76 cm ± 0.16 cm) width
B cm) by adjusting the leveling legs.
*Range can be raised approximately 1" (2.54
D
**Model/serial/rating plates may be rotated
C up from behind the
control panel for viewing from the front of the range.
†Excludes handles. Dimension given is from wall to front of oven doors
and will vary based
A on electric outlet receptacle installation.
C*
E
A*
Anti-tip bracket:
Anti-tip bracket must be securely mounted
to subfloor or wall. Thickness of flooring
J
may require longer screws
to anchor bracket
G
to subfloor. Longer
I screws are available
F
from your local hardware
H store.
D
F
E†
K
Slide-In Electric Ranges
PRODUCT DIMENSIONS
Countertop Preparation
YKESS908S, YKESS907
30"/76.2 cm
opening
width
30"/76.2 cm
3/8"/0.95
cm
223/4"
or tiled
303/4 "/78.1 cm Formed
countertop trimmed
/ " (0.95 cm) back at front
corners of countertop
opening
38
355/8"/90.5 cm*
height to
underside of
cooktop edge
with leveling
legs screwed
all the way in
23"/58.4 cm
countertop
notch to rear
of cooktop
Countertop must be level. Place level on countertop –
first side-to-side, then front-to-back. If countertop is not
level, range will not be level. Oven must be level for
satisfactory baking conditions.
Model/serial number
plate (located on the
right-hand side oven
door trim)
YKESS908S
271/4"/69.2 cm**
30"/76.2 cm
YKESS907
2711/16"/70.3 cm
from handle to standoff at
back of range
*Range
(2.54
cm)cm)
by by
adjusting
the leveling legs.
* Rangecan
canbeberaised
raisedapproximately
approximately1"1"
(2.54
adjusting
the
legs.
**W
henleveling
installed
in a 24" (61 cm) base cabinet with 25" (63.5 cm) countertop,
front ofinstalled
oven door
1 ¾"base
(4.4cabinet
cm) beyond
cm)cm)
base
cabinet.
**When
in protrudes
a 24" (61 cm)
with24"
25"(61
(63.5
countertop,
front of oven door protrudes 13/4" (4.4 cm) beyond 24" (61 cm) base cabinet.
Anti-tip bracket:
Anti-tip bracket:
Anti-tip bracket
must be securely
Anti-tip bracket must be securely
mounted mounted
to subfloor.
Thickness
of of
to subfloor.
Thickness
flooring may
require
longerlonger
screws
flooring
may require
screws
anchor bracket
to subfloor.
to anchortobracket
to subfloor.
Longer screws are available
Longer screws
are
available
from
from your local hardware
store.
your local hardware store.
Cabinet opening dimensions shown are for 25" (63.5 cm) countertop depth,
24" (61 cm) base cabinet depth, and 36" (91.4 cm) countertop height.
12
KitchenAid
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change withoutFornotice.
minimum
13"/33 cm max.
upper cabinet depth
30"/76.2 cm min.
clearance to
top of cooktop,
see NOTES.
Cooktop sides of range fit over
edges of countertop opening.
Countertop must be level. Place lev
countertop, first side-to-side; then
If countertop is not level, range wil
Oven must be level for satisfactory
Commercial-Style Dual Fuel Ranges
PRODUCT DIMENSIONS
KDRU767V, KDRU707V, KDRS467V, KDRS407V
A
B*
A.Optional backguard may be installed
B.273⁄4" (70.5 cm) depth with control panel
C.353⁄4"(90.8 cm) cooktop height when setting on the
wheels
D. Width
36-Inch (91.4 cm) Models: 36" (91.4 cm)
30-Inch (76.2 cm) Models: 30" (76.2 cm)
E. Model/serial rating plate location
C
E
*When installed in a 24" (61 cm) base cabinet with
25" (63.5 cm) countertop, front of oven door protrudes
17⁄8" (4.8 cm) beyond 24" (61 cm) base cabinet.
D
Cutout DIMENSIONS
C
D
B
F
O*
E
A
J
I
G
H
Gas
installation
area
I
J
Electrical
installation
area
K
L
A.18" (45.7 cm) upper cabinet to countertop
B.Min. upper cabinet width
36-Inch (91.4 cm) Models: 36" (91.4 cm)
30-Inch (76.2 cm) Models: 30" (76.2 cm)
C.13" (33 cm) max. upper cabinet depth
D.Min. clearance between top of cooking
platform and bottom of uncovered
wood or metal cabinet
36-Inch (91.4 cm) Models: 42" (106.7 cm)
30-Inch (76.2 cm) Models: 30" (76.2 cm)
E. 36-Inch (91.4 cm) Models: 36" (91.4 cm)
30-Inch (76.2 cm) Models: 30" (76.2 cm)
F. 6" (15.2 cm) min. clearance from both
sides of range to side wall or other
combustible material
G.15" (38.1 cm)
H.36-Inch (91.4 cm) Models: 28" (71.1 cm)
30-Inch (76.2 cm) Models: 22" (55.9 cm)
I.11⁄2" (3.8 cm)
J. 3" (7.6 cm)
K.5" (12.7 cm)
L. 36-Inch (91.4 cm) Models: 14" (35.6 cm)
30-Inch (76.2 cm) Models: 6" (15.2 cm)
M.101⁄2" (26.7 cm)
N.6" (15.2 cm)
O.3" (7.6 cm)*
*If back wall is constructed of a combustible
material and a backguard is not installed, a 6"
(15.2 cm) minimum clearance is required for all
ranges.
N
M
Dimensions
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
Cooking
Anti-tipAnti-tip
bracket:
bracket:
Anti-tipAnti-tip
bracket
mustmust
be be
securely
bracket
securely mounted
mounted
to subfloor
or wall.
Thicknessofofflooring
flooring
to subfloor
or wall.
Thickness
may require
longer
screws
anchor bracket
may require
longer
screws
totoanchor
bracket
to subfloor. Longer screws are available
to subfloor.
Longer
screws
are
available
from your local hardware store.
from your local hardware store.
Important Installation Information Regarding the Steam Function
The steam function on select ranges is configured for direct plumbing
to a nearby water supply. Included with the product are the water filter
housing, one water filter, a small section of copper tubing at the back
of the range, and a water supply union to attach the copper tubing to
the water supply line. Water supply lines are not included. The water
filtration system should be installed upright and adjacent to the range
near the cold water supply pipe under the kitchen sink.
See Installation Instructions for complete details.
KitchenAid
13
Built-In Single Ovens
Dimensions – shown in inches/cm
30-inch/76.2 cm
KEBU107S
30-inch/76.2 cm
KEBS107S
KEBK101S
27-inch/68.6 cm
KEBS177S
KEBK171S
24-inch/61 cm
KEBC147V
285⁄16 / 71.9
285⁄16 / 71.9
255⁄16 / 64.3
223⁄8 / 56.8
Overall Height (B)
283⁄4 / 73
283⁄4 / 73
283⁄4 / 73
29 / 73.7
Overall Width (C)
29 ⁄4 / 75.6
29 ⁄4 / 75.6
263⁄4 / 67.9
233⁄4 / 60.3
model no.
Product dimensions
Recessed Width (A)
3
3
Recessed Depth (D)
23 / 58.4
23 / 58.4
23 / 58.4
23 / 58.4
Recessed Height (E)
271⁄2 / 69.9
271⁄2 / 69.9
271⁄2 / 69.9
271⁄2 / 69.9
Width (F)
281⁄2 / 72.4
281⁄2 / 72.4
251⁄2 / 64.8
221⁄2 / 57.2
Height (G)
27 ⁄4 / 70.5
27 ⁄4 / 70.5
27 ⁄4 / 70.5
273⁄4 / 70.5
Depth (H)
23 / 58.4
23 / 58.4
23 / 58.4
231⁄4 / 59
cutout dimensions
3
PRODUCT DIMENSIONS
Min. Cabinet Width
Min.30,
Cabinet
Width
" 27," 24"
30" 61 cm
76.2, 68.6,
24"/61cm
H
23"/58.4cm
Min. Cabinet Width
(24," 27," 30")
recessed
oven depth
1"/2.54 cm
GF
EF
top of cutout
to bottom
of upper
cabinet
door
oven
front
cabinet
F
E
C
11/2"/3.81 cm min.
32"/81.3 cm
bottom of
cutout to top
of cabinet door
Important Installation Information
Regarding the Steam Function24"/61cm
The steam function on this oven
is configured
23"/58.4cm
for direct plumbing to a nearby water supply.
Included with the product are the recessed
water filter
depthof
housing, one water filter, a small oven
section
copper tubing at the back of the oven, and a
oven
water supply union tocabinet
attach the copper tubing front
to the water supply line. Water supply lines are
not included. The water filtration system should
be installed upright and adjacent to the oven near
the cold water supply pipe under the kitchen sink.
See Installation Instructions for complete details.
Cabinet Side View
KitchenAid
Cabinet Side View
B
E
14
3
CUTOUT DIMENSIONS
A
D
3
bottom
of cutout
to floor
Undercounter
Min. Cabinet Width
30,Cabinet
" 27," 24"
Min.
Width
" 27," 61
30")cm
76.2,(24,
68.6,
GF
EF
Single Oven
Undercounter
Cabinet Side View
Min. Cabinet Width
(24," 27," 30")
Single Oven
Undercounter
1" min.
LOCATION REQUIREMENTS
top of cutout
Electrical supply junction box should be located to bottom
3" (7.6 cm) maximum below the support surface of upper
F is installed in aEwall cabinet. A 1"cabinet
11/2"/3.81 cm min. when the oven
door
top of cutout
(2.54 cm) minimum diameter hole should have
to underside
of countertop
been drilled in the right rear or left rear corner of
51/4"/13.3 cm
the support surface to pass the appliance cable
bottom of
through to the junction box.
cutout to floor w/o
cooktop on top –
NOTE:
undercounter installation, it is
11/For
2" min.
32"
bottom ofthat the junction box be located bottom
5
recommended
11/2"
4 /8"/11.7 cm
cutout to
of cutout
bot
in the adjacent
bottom of
top ofright or left cabinet. If you are to floor
cutout
cutout to floor
installingcabinet
the junction box on rear wall behind
of cabine
w/cooktop on top
door
oven, the junction
box must be recessed and
located in the upper or lower right or left corner
of the cabinet; otherwise,
the oven
will not fit
Single
Oven
into the cabinet opening.
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
Built-In Double Ovens
Dimensions – shown in inches/cm
30-inch/76.2 cm
KEBU208S
30-inch/76.2 cm
KEBS208S
27-inch/68.6 cm
KEBS278S
24-inch/61 cm
KEBC247V
Recessed Width (A)
285⁄16 / 71.9
285⁄16 / 71.9
255⁄16 / 64.3
223⁄8 / 56.8
Overall Height (B)
50 ⁄4 / 128.9
50 ⁄4 / 128.9
50 ⁄4 / 128.9
51 / 129.5
Overall Width (C)
29 ⁄4 / 75.6
29 ⁄4 / 75.6
26 ⁄4 / 67.9
233⁄4 / 60.3
Recessed Depth (D)
23 / 58.4
23 / 58.4
23 / 58.4
23 / 58.4
Recessed Height (E)
49 ⁄16 / 126.9
49 ⁄16 / 126.9
49 ⁄16 / 126.9
491⁄2 / 125.7
Width (F)
281⁄2 / 72.4
281⁄2 / 72.4
251⁄2 / 64.8
221⁄2 / 57.2
Height (G)
493⁄4 / 126.4
493⁄4 / 126.4
493⁄4 / 126.4
493⁄4 / 126.4
Depth (H)
23 / 58.4
23 / 58.4
23 / 58.4
231⁄4 / 59
model no.
Product dimensions
3
3
3
3
3
9
9
3
9
cutout dimensions
PRODUCT DIMENSIONS
CUTOUT DIMENSIONS
Min. Cabinet Width
" 27," 24"
Min.30,
Cabinet
Width
76.2, 68.6, 61 cm
A
24"/61cm
H
23"/58.4cm
1"/2.54 cm
B
E
Cabinet Side View
GF
FE
top of cutout
to bottom
of upper
cabinet
door
M
recessed
oven depth
cabinet
oven
front
F
Cabinet Side View
11/2"/3.81 cm min.
D
C
bottom of
cutout to floor
LOCATION REQUIREMENTS
Electrical supply junction box should be located 3"
(7.6 cm) maximum below the support surface when
the oven is installed in a wall cabinet. A 1" (2.54 cm)
minimum diameter hole should have been drilled
in the right rear or left rear corner of the support
surface to pass the appliance cable through to the
junction box.
Cooking
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
Dimensions
Important Installation Information
Regarding the Steam Function
The steam function on this oven is configured
for direct plumbing to a nearby water supply.
Included with the product are the water filter
housing, one water filter, a small section of
copper tubing at the back of the oven, and a
water supply union to attach the copper tubing
to the water supply line. Water supply lines are
not included. The water filtration system should
be installed upright and adjacent to the oven near
the cold water supply pipe under the kitchen sink.
See Installation Instructions for complete details.
bottom of
cutout to top
of cabinet door
143/4"/37.5 cm
KitchenAid
15
Built-In Combination Ovens
Dimensions – shown in inches/cm
30-inch/76.2 cm
model no.
27-inch/68.6 cm
KEHU309S
KEMS308S
KEMS378S
Recessed Width (A)
285⁄16 / 71.9
285⁄16 / 71.9
255⁄16 / 64.3
Overall Height (B)
42 ⁄16 / 107.5
42 ⁄16 / 107.5
425⁄16 / 107.5
Overall Width (C)
293⁄4 / 75.6
293⁄4 / 75.6
263⁄4 / 67.9
Recessed Depth (D)
23 / 58.4
23 / 58.4
23 / 58.4
Recessed Height (E)
40 ⁄4 / 103.5
40 ⁄4 / 103.5
403⁄4 / 103.5
Width (F)
281⁄2 / 72.4
281⁄2 / 72.4
251⁄2 / 64.8
Height (G)
411⁄4 / 104.8
411⁄4 / 104.8
411⁄4 / 104.8
Depth (H)
23 / 58.4
23 / 58.4
23 / 58.4
Product dimensions
5
5
3
3
cutout dimensions
CUTOUT DIMENSIONS
PRODUCT DIMENSIONS
Min. Cabinet Width
30," 27"Width
Min. Cabinet
76.2,30"
68.6 cm
A
Cabinet Side View
24"/61cm
H
23"/58.4cm
recessed
oven depth
1"/2.54 cm
B
E
GF
EF
top of cutout
to bottom
of upper
cabinet
door
Min. Cab
(24,"
cabinet
oven
front
Cabinet Side View
19 /4"/48.9 cm
1
11/2"/3.81 cm min.
C
D
bottom
of cutout
to floor
bottom of
cutout to top
of cabinet door
Combination oven
Important Installation Information
Regarding the Steam Function
The steam function on this oven is configured
for direct plumbing to a nearby water supply.
Included with the product are the water filter
housing, one water filter, a small section of
copper tubing at the back of the oven, and a
water supply union to attach the copper tubing
to the water supply line. Water supply lines are
not included. The water filtration system should
be installed upright and adjacent to the oven near
the cold water supply pipe under the kitchen sink.
See Installation Instructions for complete details.
16
KitchenAid
LOCATION REQUIREMENTS
Electrical supply junction box should be located 3"
(7.6 cm) maximum below the support surface when
the oven is installed in a wall cabinet. A 1" (2.54 cm)
minimum diameter hole should have been drilled
in the right rear or left rear corner of the support
surface to pass the appliance cable through to the
junction box.
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
F
E
Singl
Unde
Gas Cooktops
Dimensions – shown in inches/cm
36-INCH/91.4 CM
MODEL NO.
30-inch/76.2 cm
KFGU766V
KFGS366V
KFGU706V
KFGS306V
KGCK306V
KGCC506R
Width – Widest Point (A)
361⁄4 / 92
361⁄4 / 92
303⁄16 / 76.7
303⁄16 / 76.7
317⁄16 / 79.9
303⁄16 / 76.7
Depth (B)
21 / 53.3
21 / 53.3
21 / 53.3
21 / 53.3
21 ⁄4 / 54
205⁄16 / 51.6
3 / 7.6
3 / 7.6
3 / 7.6
3 / 7.6
2 ⁄8 / 7.3
27⁄8 / 7.3
Width (D)
351⁄4 / 89.5
351⁄4 / 89.5
29 / 73.7
29 / 73.7
29 / 73.7
29 / 73.7
Depth (E)
20 / 50.8
20 / 50.8
20 / 50.8
20 / 50.8
19 /48.3
19 /48.3
Minimum Clearance to
Rear Combustible Surface (F)
2 ⁄8 / 7.3
2 ⁄8 / 7.3
2 ⁄8 / 7.3
2 ⁄8 / 7.3
2 ⁄8 / 7.3
27⁄8 / 7.3
Minimum Clearance to
Combustible Side Wall –
Both Sides (G)
8 / 20.3**
8 / 20.3**
8 / 20.3**
8 / 20.3**
83⁄8 / 21.3
83⁄8 / 21.3
Minimum to Countertop
Front Edge (H)
11⁄8 / 2.9
11⁄8 / 2.9
11⁄8 / 2.9
11⁄8 / 2.9
21⁄8 / 5.4
21⁄8 / 5.4
PRODUCT DIMENSIONS
Burner Box Height* (C)
1
7
CUTOUT DIMENSIONS
7
7
7
7
7
*Power/fuel supply/vent connections extend below cooktop and are not included in burner height dimensions.
**The combined distance from the left and right sidewalls must be a minimum of 48" (121.9 cm).
PRODUCT DIMENSIONS
A
B
C
CUTOUT DIMENSIONS
13"/33 cm max.
upper cabinet depth
Combustible area
above countertop
18"/45.7 cm min. clearance
upper cabinet to countertop
within minimum horizontal
clearances to cooktop
See note
for minimum
clearances.
F
HHmin.
E
24"/61 cm min.–
deep countertop
is required.
G
G
D
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
Cooking
Gas line opening –
Wa ll: anywhere 5"/12.7 cm below
underside of countertop.
Cabinet floor: anywhere within
6"/15.2 cm of rear wall is recommended.
Grounded outlet –
Locate within 24"/61 cm
of right rear corner
of cutout.
Dimensions
Do not seal cooktop
to countertop.
NOTES: 24" (61 cm) minimum clearance when
bottom of wood or metal cabinet is covered by not
less than 1⁄4" (0.635 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet steel,
0.015" (0.038 cm) stainless steel, 0.024" (0.06 cm)
aluminum, or 0.020" (0.05 cm) copper.
30" (76.2 cm) minimum clearance between the
top of the cooking platform and the bottom of an
unprotected wood or metal cabinet.
If installing a hood or microwave hood combination
above the range, follow hood or microwave hood
combination installation instructions for dimensional
clearances above the cooking surface.
KitchenAid
17
Gas Cooktop & Built-In Oven Combination
APPROVED MODEL NUMBER COMBINATIONS
GAS Cooktops*
KFGU766V, KFGS366V, KFGU706V, KFGS306V, KGCK306V, KGCC506R
Built-In Ovens
KEBU107S, KEBS107S, KEBK101S, KEBS177S, KEBK171S, KEBC147V
*Cooktops should not be placed over a built-in oven without installing
the heat shield that is shipped with the product. See Installation Instructions
for specific information.
CUTOUT DIMENSIONS
B
A
C
D
D
E
E
F
G
H
I
J
M
L
K
N
A. 24" (61 cm) cabinet depth
B.1" (2.54 cm) clearance from the top of junction box
to bottom of countertop
C. 25" (63.5 cm) countertop depth
D. Recommended oven junction box locations
E. 1" (2.54 cm) clearance from the side of junction box to cabinet wall
F.273⁄4" (70.5 cm) minimum cutout height
G.Allow 5⁄8" (1.6 cm) for oven to overlap each side
H. 36" (91.4 cm) from cabinet base to countertop
I. Gas line through wall 101⁄2" (26.7 cm) to centre of cutout
J.31⁄4" (8.3 cm)
K. Gas line through floor 101⁄2" (26.7 cm) to centre of cutout
L.31⁄2" (8.9 cm)
M.45⁄8" (11.7 cm)
N. See chart below
Dimensions – shown in inches/cm
Oven Size
Oven Cutout
Dimension
36"/91.4 30"/76.2 27"/68.6
341⁄2 /
87.6
281⁄2 /
72.4
251⁄2 /
64.8
NOTE: Lower shaded areas are recommended locations for flexible
or rigid gas pipe installation. The gas pipe can be installed on either
side of the cutout and either through the floor or through the wall.
The shaded area not used for oven junction box is recommended
for 120-volt grounded outlet for cooktop.
18
KitchenAid
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
24"/61
221⁄2 /
57.2
Commercial-Style Rangetops
PRODUCT DIMENSIONS
KGCU484V, KGCU482V, KGCU462V, KGCU467V,
KGCU407V
C
D
A.48-Inch (121.9 cm) Models: 477⁄8" (121.6 cm)
36-Inch (91.4 cm) Models: 357⁄8" (91.1 cm)
30-Inch (76.2 cm) Models: 297⁄8" (75.9 cm)
B.36" (91.4 cm) long 3-prong grounding-type power supply cord
C.Model/serial rating plate (located on the underside of the rangetop burner box)
D.Island trim or optional backguard
E.273⁄4" (70.5 cm)
E
B
A
Cutout DIMENSIONS
A. Rangetop cutout to back wall
KGCU484V, KGCU482V,
KGCU462V: 11⁄2" (3.8 cm)
C
KGCU407V, KGCU467V: 13⁄4" (4.4 cm)
B. Rangetop to cabinet
P
48-Inch (121.9 cm) Models:
42" (106.7 cm) min.
F
C
36-Inch (91.4 cm) Models:
B min.**
42" (106.7 cm) min.
O
D
A*
G
30-Inch (76.2 cm) Models:
30" (76.2 cm) min.
J
N
H
C. Optional backguard opening
E
I
48-Inch (121.9 cm) Models:
L
48" (121.9 cm)
K
M
36-Inch (91.4 cm) Models:
D
36" (91.4 cm)
E
30-Inch (76.2 cm) Models:
30" (76.2 cm)
D. Cabinet and countertop
48-Inch (121.9 cm) Models:
471⁄4" (120 cm)
*If back wall is constructed of a combustible material and a backguard is not installed,
a minimum clearance of dimension A + 6" (15.2 cm) is required for 48" (121.9 cm)
36-Inch (91.4 cm) Models:
rangetops and model KGCU462V.
351⁄4" (89.5 cm)
**Dimension “B” can be reduced by 6" (15.2 cm) when bottom of wood or metal cabinet is
30-Inch (76.2 cm) Models:
protected by not less than 0.25" (0.635 cm) flame retardant millboard covered with not
291⁄4" (74.3 cm)
less than No. 28 MSG sheet metal, 0.015" (0,038 cm) stainless steel, 0.024" (0.06 cm)
E. Countertop only
aluminum, or 0.020" (0.05 cm) copper.
48-Inch (121.9 cm) Models:
If installing a hood above the rangetop, follow the hood instructions for dimensional
48" (121.9 cm) or (477⁄8"/121.6 cm†)
clearances above the cooking surface.
36-Inch
(91.4 cm) Models:
†Zero clearance fit.
36" (91.4 cm) or (357⁄8"91.1 cm†)
30-Inch (76.2 cm) Models:
30" (76.2 cm) or (297⁄8"/75.9 cm†)
F. 18" (45.7 cm) min. clearance upper
cabinet to countertop
G. 3⁄4" (1.9 cm) back of cabinet cutout
to gas opening cutout
H.67⁄8" (17.5 cm) gas opening cutout
depth
I.121⁄2" (31.7 cm) gas opening cutout
width
J.221⁄4" (56.5 cm) cabinet cutout depth
K. 2" (5.1 cm) cabinet side to gas
cutout
L. 6" (15.2 cm) min. distance on both
sides of the rangetop to the side
wall or other combustible material
above cooking surface
M.24" (61 cm) cabinet depth
N. 71⁄4" (18.4 cm) cabinet depth to
countertop
O. Notch to be equal on both sides
P. 13" (33 cm) upper cabinet depth
Gas and Electric Connection Lines
Dimensions
B
C
A
Cooking
A.Grounded 3-prong outlet should be located on left-hand side of
cutout 16" (40.6 cm) max. from enclosure sidewall
B.10" (25.4 cm) min. clearance from countertop to top of the outlet
C.14" (35.6 cm) countertop to the gas supply line
D.Gas supply line should be located in this area on rear or side walls,
or the supply line can come up through the floor
NOTE: Solid side and bottom of cutout enclosure not shown.
D
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
KitchenAid
19
B
C
Gas Downdraft Cooktop
PRODUCT DIMENSIONS
KGCD807X
A
B
A
C
D
E
B
F
C
G
A. KGCD807XSS: 2137⁄64" (54.8 cm)
B.193⁄4" (50.2 cm) screw head to screw head
C. Model/serial rating/clearance plate location
H
J
A
I
B.KGCD807XSS:
301⁄32" (76.3 cm)
C.121⁄2" (31.7 cm)
centreline of cooktop
to centreline of gas
manifold pipe
D.75⁄16" (18.6 cm)
E.35⁄8" (9.2 cm)
F. 15" (38.1 cm)
G.23⁄16" (5.6 cm)
recommended
minimum cabinet to
motor clearance
H.143⁄8" (36.5 cm)
I.1113⁄16" (30 cm)
J.283⁄8" (72.1 cm) screw
head to screw head
Cutout DIMENSIONSB
C
D
A
D
E
B
C
F
L E
N
G
F
G
H
H M
K
II
J
K
J
M
B
A
D
C
F
H
I
J
20
KitchenAid
G
A. 30" (76.2 cm)
B. Combustible area above countertop (shown by dashed box)
C.30" (76.2 cm) minimum clearance between top of cooktop platform and bottom of
uncovered wood or metal cabinet (24"/61 cm minimum clearance if bottom of wood
or metal cabinet is covered by not less than 1⁄4" (0.635 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet steel, 0.015" (0.038 cm) stainless steel,
0.024" (0.06 cm) aluminum, or 0.020" (0.05 cm) copper)
D. 13" (33 cm) recommended upper cabinet depth
E.21⁄8" (5.4 cm)
F.1915⁄16" (50.6 cm)
G.18" (45.7 cm) minimum clearance from upper cabinet to countertop within minimum
horizontal clearances to cooktop
H. Junction box or outlet: 12" (30.5 cm) minimum from bottom of countertop
I. Junction box or outlet: 10" (25.4 cm) from right-hand side of cabinet
J.285⁄8" (72.7 cm)
K. 8" (10.5 cm) minimum distance to nearest left and right side combustible surface
above cooktop
L. 2" (5.1 cm) minimum clearance between back wall and countertop
M.Gas line opening – wall: anywhere 6" (15.2 cm) below underside of countertop on the
left side; cabinet floor: anywhere within 6" (15.2 cm) of rear wall on the left side is
recommended.
N. 25" (63.5 cm) depth of countertop
Notes: After making the countertop cutout, some installations may require notching
down the base cabinet side walls to clear the cooktop base. To avoid this modification,
use a base cabinet with side walls wider than the cutout.
•A
minimum side clearance of 6" (15.2 cm) is recommended between side of cooktop
and side wall for maximum ventilation performance.
•A
minimum clearance of 2" (5.1 cm) is recommended between the motor/blower and
cabinet for proper cooling. A 6" (15.2 cm) clearance is recommended for servicing access.
E
A. 285⁄8" (72.7 cm) maximum
B. 1915⁄16" (50.6 cm) maximum
C. 95⁄16" (23.6 cm)
D. 613⁄16" (17.3 cm)
E. 21⁄8" (5.4 cm)minimum space
to front edge of cooktop
F. Floor exhaust option
G. 61⁄8" (15.6 cm) for 6" (15.2 cm) vent
system; 51⁄8" (13 cm) for 5" (12.7 cm)
vent system
H.95⁄16" (23.6 cm)
I.133⁄8" (34 cm) from the top of the
countertop surface
J. Wall exhaust option
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
B
Electric Downdraft Cooktops
C
PRODUCT DIMENSIONS
KECD867X, KECD807X
A
A. KECD867XSS: 3529⁄64" (90 cm)
KECD807XSS: 301⁄32" (76.3 cm)
C. KECD867X: 171⁄2" (44.4 cm)
KECD807X: 145⁄16" (36.3 cm)
D. KECD867X: 313⁄16" (9.7 cm)
KECD807X: 4" (10.2 cm)
E.1813⁄32" (46.7 cm)
F. KECD867X: 85⁄16" (21.1 cm)
KECD807X: 13⁄8" (3.5 cm)
G.131⁄8" (33.6 cm)
H. KECD867X: 131⁄16" (33.2 cm)
KECD807X: 143⁄16" (36 cm)
I. Screw head to screw head
KECD867X: 341⁄2" (87.6 cm)
KECD807X: 285⁄8" (72.7 cm)
B
C
D
A
B
E
C
F
H
G
I
A.KECD867XSS, KECD807XSS: 22" (55.9 cm)
B. 21" (53.3 cm) screw head to screw head
C. Model/serial rating/clearance plate location
A
B
C
Cutout DIMENSIONS
A
D
E
D
B
C
L
G
N F
F
E
G
H
I
H
I
K
J
K
B
A
F
I
J
A. KECD867X: 349⁄16" (87.8 cm) maximum
KECD807X: 287⁄8" (73.3 cm) maximum
B.211⁄8" (53.7 cm) maximum
C. KECD867X: 157⁄16" (39.2 cm)
KECD807X: 85⁄8" (21.9 cm)
D.65⁄16" (16 cm)
E. 2" (5.1 cm) minimum space to front
edge of cooktop
F. Floor exhaust option
G.61⁄8" (15.6 cm) for 6" (15.2 cm) vent
system; 51⁄8" (13 cm) for 5" (12.7 cm)
vent system
H. KECD867X: 157⁄16" (39.2 cm)
KECD807X: 85⁄8" (21.9 cm)
I. 16" (40.6 cm)
J. Wall exhaust option
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
Cooking
G
E
Dimensions
D
C
H
A. KECD867X: 36" (91.4 cm)
KECD807X: 30" (76.2 cm)
B. Combustible area above countertop (shown by dashed box)
C. 30" (76.2 cm) minimum clearance between top of cooktop platform and bottom of
uncovered wood or metal cabinet (24"/61 cm minimum clearance if bottom of wood or
metal cabinet is covered by not less than 1⁄4" (0.635 cm) flame retardant millboard covered
with not less than No. 28 MSG sheet steel, 0.015" (0.038 cm) stainless steel, 0.024"
(0.06 cm) aluminum, or 0.020" (0.05 cm) copper)
D. 13" (33 cm) recommended upper cabinet depth
E. 2" (5.1 cm)
F.211⁄8" (53.7 cm)
G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop within minimum
horizontal clearances to cooktop
H. Junction box or outlet: 12" (30.5 cm) minimum from bottom of countertop
I. Junction box or outlet: 10" (25.4 cm) from right-hand side of cabinet
J. KECD867X: 349⁄16" (87.8 cm)
KECD807X: 287⁄8" (73.3 cm)
K.21⁄2" (6.3 cm) minimum distance to nearest left and right side combustible surface above
cooktop
L.11⁄2" (3.8 cm) minimum clearance between back wall and countertop
NOTES: After making the countertop cutout, some installations may require notching
down the base cabinet side walls to clear the cooktop base. To avoid this modification,
use a base cabinet with side walls wider than the cutout.
•A
minimum side clearance of 6" (15.2 cm) is recommended between side of cooktop
and side wall for maximum ventilation performance.
•A
minimum clearance of 2" (5.1 cm) is recommended between the motor/blower and
cabinet for proper cooling. A 6" (15.2 cm) clearance is recommended for servicing access.
KitchenAid
21
Induction Cooktops
PRODUCT DIMENSIONS
KICU569X, KICU509X
A
B
C
A.KICU569X: 365⁄16" (92.2 cm)
KICU509X: 303⁄4" (78.1 cm)
B.215⁄16" (54.1 cm)
C.33⁄32" (7.9 cm)
CUTOUT DIMENSIONS
A
13"/33 cm upper
cabinet depth
Combustible area
above countertop
18"/45.7 cm min. clearance
upper cabinet to countertop
within minimum horizontal
clearances to cooktop
See NOTES
for minimum
clearances.
1"/2.54 cm
2"/5.1 cm
C1/2"
20
A.KICU569X: 36" (91.4 cm)
KICU509X: 30" (76.2 cm)
B.KICU569X: 351⁄2" (90.2 cm)
KICU509X: 2917⁄32" (75 cm)
C.KICU569X: 201⁄2" (52.1 cm)
KICU509X: 195⁄16" (49 cm)
1"/2.54 cm
1"/2.54 cm
B
NOTES: 24"
cm)cm)
min.minimum
clearance ifclearance
bottom of wood
metal of wood
NOTES:
24"(61(61
whenorbottom
cabinet is protected by not less than 1/4" (0.635 cm) flame
retardant millboard
orcovered
metalwith
cabinet
is covered by not less than 1⁄4" (0.635
cm) flame
not less than No. 28 MSG sheet steel, 0.015" (0.038 cm)
retardant
millboard
covered
with notorless
than
No.cm)28copper
MSG
stainless steel,
0.024" (0.06
cm) aluminum,
0.020"
. (0.05
sheet steel, 0.015" (0.038 cm) stainless steel, 0.024" (0.06 cm)
30" (76.2 cm) min. clearance between top of cooktop platform and
aluminum,
or 0.020"wood
(0.05
bottom of unprotected
or cm)
metalcopper.
cabinet.
30"
(76.2 cm)
minimum
between
the top of the cooking
If installing
a hood
above theclearance
cooktop, follow
hood instructions
platform
and the
bottom
of an
wood or metal cabinet.
for dimensional
clearances
above
theunprotected
cooktop surface.
If installing a hood or microwave hood combination above the
range, follow hood or microwave hood combination installation
instructions for dimensional clearances above the cooking surface.
22
KitchenAid
Junction box or outlet;
12"/30.5 cm minimum from
bottom of countertop;
10"/25.4 cm from right
side of cabinet
Electrical Requirements:
A 4-wire or 3-wire, single phase, 240 volt,
60 Hz., AC only electrical supply is required
on a separate, 50-amp circuit (36"/91 4 cm
model) or 40-amp circuit (30"/76.2 cm
model), fused on both sides of the line.
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
Electric Cooktops
Dimensions – shown in inches/cm
36-INCH/91.4 cm
MODEL NO.
PRODUCT DIMENSIONS
Width (A)
Depth (B)
Burner Box Height* (C)
30-INCH/76.2 CM
15-INCH/38.1 cm
KECC568R
KECC508R
KECC507R
KECC506R
KECC056R
365⁄16 / 92.2
215⁄16 / 54.1
27⁄8 / 7.3
305⁄16 / 77
215⁄16 / 54.1
27⁄8 / 7.3
305⁄16 / 77
215⁄16 / 54.1
27⁄8 / 7.3
305⁄16 / 77
215⁄16 / 54.1
27⁄8 / 7.3
169⁄16 / 42.1
215⁄16 / 54.1
27⁄8 / 7.3
351⁄2 / 90.2
201⁄2 / 52.1
291⁄2 / 74.9
201⁄2 / 52.1
291⁄2 / 74.9
201⁄2 / 52.1
291⁄2 / 74.9
201⁄2 / 52.1
141⁄2 / 36.8
201⁄2 / 52.1
1 / 2.54
1 / 2.54
1 / 2.54
1 / 2.54
1 / 2.54
2 / 5.1
2 / 5.1
2 / 5.1
2 / 5.1
2 / 5.1
Cutout DIMENSIONS
Cutout Width (D)
Cutout Depth (E)
Minimum Clearance to
Side Wall – Both Sides (F)
Minimum to Countertop
Front Edge (G)
*Power/fuel supply/vent connections extend below cooktop and are not included in burner box height dimensions.
PRODUCT DIMENSIONS
A
B
C
CUTOUT DIMENSIONS
13"/33 cm upper
cabinet depth
Combustible area
above countertop
18"/45.7 cm min. clearance
upper cabinet to countertop
within minimum horizontal
clearances to cooktop
See NOTES
for minimum
clearances.
E
F
F
D
Junction box or outlet;
12" (30.5 cm) minimum from
bottom of countertop;
10" (25.4 cm) from right
side of cabinet
NOTES: 24" (61 cm) minimum clearance when bottom of wood
or metal cabinet is covered by not less than 1⁄4" (0.635 cm) flame
retardant millboard covered with not less than No. 28 MSG
sheet steel, 0.015" (0.038 cm) stainless steel, 0.024" (0.06 cm)
aluminum, or 0.020" (0.05 cm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an unprotected wood or metal cabinet.
If installing a hood or microwave hood combination above the
range, follow hood or microwave hood combination installation
instructions for dimensional clearances above the cooking surface.
Cooking
above the cooktop, follow hood instructions
arances above the cooktop surface.
Dimensions
min. clearance if bottom of wood or metal
by not less than 1/4" (90.635 cm) flame retardant
with not less than No. 28 MSG sheet steel, 0.015"
steel, 0.024" (0.06 cm) aluminum,
copper.
between top of cooktop platform and
ted wood or metal cabinet.
G
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
KitchenAid
23
Electric Cooktop & Retractable Downdraft System Combination
Dimensions – shown in inches/cm
model no.
installed with retractable
downdraft system model no.
36-inch/91.4 CM*
KECC568R
30-inch/76.2 CM*
KECC508R
KECC507R
KECC506R
KIRD861V
KIRD801V
cutout dimensions
Width Cooktop and Downdraft Vent System (A)
371⁄2 / 95.2
311⁄2 / 80
Width Cooktop (B)
365⁄16 / 92.2
305⁄16 / 77
Width Downdraft Vent System (C)
331⁄2 / 85.1
271⁄2 / 69.9
Depth Downdraft Vent System (D)
21⁄8 / 5.4
21⁄8 / 5.4
215⁄16 / 54.1
215⁄16 / 54.1
231⁄4 / 59
231⁄4 / 59
Depth Cooktop (E)
Depth Cooktop and Downdraft Vent System (F)
Depth Countertop Front Edge to Cutout (G)
Depth Countertop (H)
2 / 5.1
Countertop Preparation
1/4"/0.635 cm min.
to splashguard
or rear wall
2 / 5.1
26 ⁄8 / 68.3 min.
3/4" /1.9 cm max.
25 ⁄8 / 65.7 min.
7
7
Cooktop
backsplash depth
*Installation with retractable downdraft vent
1/2" 1.3 cm min.
system requires countertop and base cabinet
to splashguard
or rear
wall
deeper than standard 25" (63.5 cm) deep
countertop
and 24" (61 cm) deep base cabinet.
Downdraft
vent
Rear
wall
CUTOUT DIMENSIONS
IMPORTANT: Countertops with a bullnosed front
edge are not recommended for these installations.
1/4" /0.635 cm min.
to splashguard
or rear wall
D
3/4" /1.9 cm max.
B
Required min.
countertop depth
Countertop
splashguard
H
backsplash depth
1/2" /1.3 cm min.
C G
A
to splashguard
or rear wall
H
Electric Cooktop & Built-In Oven Combination
Downdraft
vent
D
F
E
Cooktop
(Overall depth of
cooktop and downdraft
vent system)
Countertop
splashguard
(Overall width of cooktop
and downdraft vent system)
C
E F
B
A
G
APPROVED MODEL NUMBER COMBINATIONS
ELECTRIC Cooktops
KECC568R, KECC508R, KECC507R, KECC506R
Built-In Ovens
KEBU107S, KEBS107S, KEBK101S, KEBS177S, KEBK171S, KEBC147V
CUTOUT DIMENSIONS
B
A
C
D
C
E
F
A. 24" (61 cm) cabinet depth
B. 25" (63.5 cm) countertop depth
C. Recommended oven and cooktop junction box locations
D.Allow 5⁄8" (1.6 cm) for oven to overlap on each side
E.273⁄4" (70.5 cm) minimum cutout height
F. 36" (91.4 cm) from cabinet base to countertop
G.45⁄8" (11.7 cm) from floor
H. See chart below
Dimensions – shown in inches/cm
Oven Size
G
Oven Cutout
Dimension
36"/91.4 30"/76.2 27"/68.6
341⁄2 /
87.6
281⁄2 /
72.4
H
24
KitchenAid
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
251⁄2 /
64.8
24"/61
221⁄2 /
57.2
Rear
wall
Built-In Microwave Ovens
Dimensions – shown in inches/cm
PRODUCT
DIMENSIONS
Product
Dimensions
30-inch/76.2 cm
KBHS109S
27-inch/68.6 cm
KBHS179S
Overall Width (A)*
293⁄4 / 75.6
263⁄4 / 67.9
Recessed Width (B)
28 ⁄16 / 71.9
255⁄16 / 64.3
Overall Height (C)
205⁄16 / 51.6
205⁄16 / 51.6
Recessed Height (D)
183⁄4 / 47.6
183⁄4 / 47.6
Overall Depth (E)**
261⁄8 / 66.4
261⁄8 / 66.4
Recessed Depth (F)
23 / 58.4
23 / 58.4
Width (G)
28 ⁄2 / 72.4
25 ⁄2 / 64.8
Height (H)
19 ⁄16 / 49.4
197⁄16 / 49.4
23 ⁄4 / 59
231⁄4 / 59
model no.
21B7/8"
Product dimensions
5
1/2"
17D
C
18"*
18F1/4"
Product Dimensions
cutout dimensions
1
7
Depth (I)
1
21E1/4" *7
21 /8"
23 3A/4"*
1
*Measurements include front facing of microwave oven.
Depth measurement also includes door handle.
171/2"
18" *
*Measurements include front facing of microwave oven and door handle.
**With flush receptacle or with non-flush receptacle located in far corner of cutout.
Cutout Top18View
1/4"
Minimum Cutout Dimensions
a
213/4"*
26 1/4"**
Cutout DIMENSIONS
KBMS1454S
221/4"***
253/4"***
283/4"***
175/8 "
Min. Cabinet Width
30," 27"Width
Min. Cabinet
(27,"68.6
30") cm
76.2,
217/8"
27"/68.6 cm
Installation
3
3
73 (± .48)
HF
top of cutout
to bottom
of upper
cabinet
door
EG
11/2"/3.8 cm min.
Cutout T
213/4" *
1/4" ** receptacle
26non-flush
*With flush receptacle, or with
I
a
located in far corner of
cutout.
1
18 /4"
**Without flush receptacle.
***See chart.
1/4" *** cm)
G22(24"/61
17
8/4"" *
215/1H
24"
27"
30"
3/4" ***
G25(27"/68.6
cm)
23 3/4" *
INSTALLATION INSTALLATION
INSTALLATION
3/4" ***
G28(30"/76.2
cm)
Width 22 1/4" (± 3/16")
25 3/4" (± 3/16")
28 3/4" (± 3/16")
**Without flush receptacle.
a
***See chart.
213/4"*
26 1/4"**
Width
GI 221/4"***
b
c
d
24"
INSTALLATION
27"
INSTALLATION
30"
INSTALLATION
22 1/4" (± 3/16")
25 3/4" (± 3/16")
28 3/4" (± 3/16")
261/4 " /
66.7 cm
E 253/4"***
283/4"***
Dimensions
Cabinet Side View
175/8 "
*NOTE: Pro
is 211/4" (5
a. Microw
b. Non-flu
c. Flush re
d. Non-flu
Cutout Top View
Minimum Cutout Dimensions
213/4 "
55.2 cm*
oven
front
cabinet
**Without flush receptacle.
***See chart.
Cabinet Side View
24"
INSTALLATION
27"
INSTALLATION
30"
INSTALLATION
Cooking
*With flush receptacle, or with non-flush receptacle
located in far corner of cutout.
*NOTE: Product depth including handle
is 211/4" (54 cm).
a. Microwave oven
b. Non-flush receptacle
c. Flush receptacle
d. Non-flush receptacle located in far corner
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
3/16")
3/4" (± 3/16")
3/4" (± 3/16")
22 1/4" (± and/or
28with
Use25
& Care
Guide packed
product. Specifications subject to change without notice.
b
*NOTE: Product depth includin
is 211/4" (54 cm).
a. Microwave oven
b. Non-flush receptacle
c. Flush receptacle
d. Non-flush receptacle locate
*Measurements include front facing of microwave oven.
Depth
measurement
40"/101.6
cmalso includes door handle.
bottom
of cutout
*With flush receptacle, or with non-flush receptacle
to floor
located in far corner of cutout.
bottom of
cutout to top
of cabinet door
Width
253⁄4 (± 3⁄16) /
65.4 (± .48)
171/2"
1"/2.54 cm min.
d
*Measurements include front facing of microwave oven.
Depth measurement also includes door handle.
30"/76.2 cm
Installation
Width (G)
28 ⁄4 (± ⁄16) /
Minimum
Cutout Dimensions
18"*
c
211/4" *
23 3/4" *
Cutout Dimensions – shown in inches/cm
Product Dimensions
KBHS109S, KBHS179S
b
KitchenAid
25
Microwave Hood Combination Ovens
PRODUCT DIMENSIONS
PRODUCT DIMENSIONS
YKHMS2050S – 30-Inch/76.2 cm
YKHMS2040W – 30-Inch/76.2 cm
151/2"
39.4 cm
181/4"
46.4 cm
185/8"/
47.3 cm
297/8"/75.9 cm
171/4"/
43.8 cm
297/8"/
75.9 cm
153/4"/
40.0 cm
CUTOUT DIMENSIONS
CUTOUT DIMENSIONS
YKHMS2050S – 30-Inch/76.2 cm
YKHMS2040W – 30-Inch/76.2 cm
2" x 4"/5.1 x 10.2 cm
wall stud
Grounded
3-prong outlet
2" x 4"/5.1 x 10.2 cm
wall stud
30"/76.2 cm
Grounded
3-prong outlet
30"/76.2 cm
min.
33"/83.8 cm
typical*
12"/30.5 cm min. –
13"/33 cm max.
69"/175.3 cm
12"/30.5 cm min. –
14"/35.6 cm max.
66"/167.6 cm min.
min.
*33" (83.8 cm) is typical for 69" (175.3 cm) installation height.
Exact dimension may vary depending on type of range/cooktop below.
26
KitchenAid
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
Countertop Microwave Ovens
Dimensions – shown in inches/cm
Model No.
PRODUCT DIMENSIONS
YKCMS1555S
PRODUCT Dimensions
Width (A)
217⁄8 / 55.2
Height (B)
121⁄2 / 31.7
Depth (C)
171⁄8 / 43.5
B
C
A
Slow Cook Warming Drawers
PRODUCT DIMENSIONS
Dimensions – shown in inches/cm
30-inch/76.2 cm
KEWS105S
27-inch/68.6 cm
KEWS175S
Overall Width (A)
293⁄4 / 75.6
263⁄4 / 67.9
Recessed Width (B)
281⁄4 / 71.8
251⁄4 / 64.1
Recessed Height (C)
9 / 22.9
9 / 22.9
Width (D)
281⁄2 / 72.4
251⁄2 / 64.8
Height (E)
91⁄8 / 23.2
91⁄8 / 23.2
Recessed Depth (F)
22 ⁄4 / 57.8
223⁄4 / 57.8
Model NO.
Product Dimensions
B
C
Cutout Dimensions
3
A
CUTOUT DIMENSIONS
Cabinet Side View
Min. Cabinet Width
" 27"Width
Min. 30,
Cabinet
(27,"68.6
30")cm
76.2,
FG
223/4"/57.8 cm
recessed warming
drawer depth
cabinet
Warming
drawer front
Single oven
cutout
Cabinet Side View
Dimensions
E
D
EF
21/2"/6.4 cm min.
Support surface
must be solid, level,
and flush with bottom
of cabinet cutout.
21/2"/6.4 cm min.
Warming
drawer
cutouts
41/4"/10.8 cm
1"/2.54 cm min.
Recommended
Toe kick
Support surface
Cooking
120-volt
grounded outlet
(or located in
adjacent cabinet)
4"/10.2 cm
Two warming drawers under
a single oven are shown.
Dimensions are for planning purposes only. For additional product information, refer to the Installation Instructions
and/or Use & Care Guide packed with product. Specifications subject to change without notice.
KitchenAid
27
No one knows the kitchen like KitchenAid .
®
®Registered Trade-mark/™ Trade-mark of KitchenAid U.S.A. The mixer shape is a registered trade-mark of KitchenAid U.S.A., KitchenAid Canada licensee in Canada.
All other trade-marks are owned by their respective companies. ©2011. All rights reserved. KitchenAid • Mississauga, Ontario L5N 3A7 Printed in Canada 08/2011
KitchenAid.ca