Automotive Data Solutions OEM-AL(RS)-TL3-[ADS-ALCA] Toyota Land Cruiser 2008 Installation Guide
Automotive Data Solutions OEM-AL(RS)-TL3-[ADS-ALCA] is a remote start and security system tailored for specific Toyota and Lexus vehicles. It offers features like vehicle immobilizer bypass, push-to-start control, and OEM alarm integration, allowing you to remotely start your car, lock and unlock doors, and control other vehicle functions. The setup includes a module, wiring harnesses, and a programming button, enabling you to configure the system according to your specific requirements. This comprehensive guide provides step-by-step instructions for installing and programming the system, ensuring a smooth and efficient process.
PDF
Download
Document
Advertisement
Advertisement
INSTALL GUIDE OEM-AL(RS)-TL3-[ADS-ALCA]-EN DOCUMENT NUMBER 83971 REVISION DATE 20231127 FIRMWARE OEM-AL(RS)-TL3-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 BEFORE INSTALLATION 1- Connect module to computer 2- Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately) www.idatalink.com PAGE 2 OF 17 VEHICLE LIST - 1 OF 1 DOC.: #83971 • 20231127 FEATURES YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS 3X LOCK START/STANDALONE MOD. PUSH TO START CTRL ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK TRUNK/HATCH RELEASE GAS TANK FLAP RELEASE TACHOMETER OUTPUT BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT* LS460 PTS 07-14 2 • • • • • • • • • • • • • • • LS600h PTS 08-14 2 • • • • • • • • • • • • • • • LX570 PTS 08-15 1 • • • • • • • • • • • • • • LandCruiser PTS 08-15 1 • • • • • • • • • • • • • • MAKE LEXUS TOYOTA POWER LIFTGATE MODEL NOTE I Keyless and smartkey systems will remain functional during remote start. * Available only if vehicle is equipped with factory hood switch. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com PAGE 3 OF 17 BOX CONTENTS - 1 OF 1 DOC.: #83971 • 20231127 BOX CONTENTS WHITE WHITE 4 PIN BLACK CONNECTOR 6 PIN WHITE CONNECTOR MODULE 1 2 3 4 5 6 1 2 3 4 5 6 7 WHITE 1 2 3 BLUE 1 2 3 PROGRAMMING BUTTON 10 PIN BLACK CONNECTOR 7 PIN WHITE CONNECTOR LED 1 A B F C E D 10 9 8 7 6 5 4 3 2 1 4 3 2 1 BLACK 3 PIN WHITE CONNECTOR DATA CABLE 1 3 PIN BLUE CONNECTOR DATA CABLE 2 BLACK DATA PORT (WEBLINK, RF, TELEMATIC) WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT 4 PIN BLACK CABLE Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com PAGE 4 OF 17 COMPONENT LOCATOR - 1 OF 1 DOC.: #83971 • 20231127 INTERIOR VIEW A DRIVER SIDE VIEW Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 PASSENGER SIDE VIEW OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com PAGE 5 OF 17 Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 POLARITY MODULE LOCATION COMPONENT LOCATOR ~ ~ 16 pin 16 Gray (DATA) Main body ECU ~ ~ ~ 16 pin 15 Red (DATA) Main body ECU ~ STSW ~ ~ 10 pin 04 Red (+) Main body ECU ~ ~ ~ 24 pin 15 Black (+) Main body ECU ~ 12V ~ ~ 01 pin 01 Black (+) Main body ECU ~ Parking light ~ ~ 26 pin 23 Violet (-) Main body ECU ~ PTS ~ ~ 14 pin 07 White (-) Push button ~ CanH ~ ~ 16 pin 16 Gray (DATA) Main body ECU ~ CanL ~ ~ 16 pin 15 Red (DATA) Main body ECU ~ STSW ~ ~ 10 pin 04 Red (+) Main body ECU ~ ~ ~ 24 pin 15 Black (+) Main body ECU ~ 12V ~ ~ 01 pin 01 Black (+) Main body ECU ~ Parking light ~ ~ 26 pin 23 Violet (-) Main body ECU ~ PTS ~ ~ 14 pin 07 White (-) Push button ~ 08-15 Ignition 08-15 Ignition WIRE COLOR CanH CanL CONNECTOR NAME POSITION WIRE DESCRIPTION CONNECTOR TYPE LandCruiser PTS YEAR MODEL LX570 PTS DOC.: #83971 • 20231127 CONNECTOR COLOR TOYOTA LEXUS MAKE TYPE 1 - WIRE CHART - 1 OF 1 OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com PAGE 6 OF 17 TYPE 1 - WIRING DIAGRAM - 1 OF 1 M6 M3 M4 PTS SWITCH CONNECTIONS ARE REQUIRED 1 ONLY IF IDLE MODE IS DESIRED M1 M2 DOC.: #83971 • 20231127 PTS (-) - 07 M5 DATA 8 9 10 11 12 13 14 1 2 3 4 5 6 7 1 1 M1 01 GRAY/YELLOW (NC) 02 GRAY/RED (NC) 03 GREEN/YELLOW (NC) 04 GREEN/RED (NC) 05 BLUE/YELLOW - PTS (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT MAIN BODY ECU 1 9 8 7 6 5 4 IGNITION (+) - 15 M2 01 PINK - IGNITION (+) INPUT 02 PINK/BLACK (NC) 03 ORANGE (NC) 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK (NC) 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 24 23 22 21 20 19 3 2 1 12 11 10 15 14 13 18 17 16 2 M3 01 YELLOW (NC) 02 YELLOW/RED (NC) 03 YELLOW/BLACK (NC) CANL - 15 CANH - 16 M4 01 WHITE - IGNITION (+) INPUT 02 WHITE/RED (NC) 03 WHITE/BLACK - STSW (+) OUTPUT 4 3 2 10 9 8 7 1 6 5 16 15 14 13 12 11 4 3 WITHOUT A COMPATIBLE ACCESSORY M5 01 BLUE/WHITE (NC) 02 WHITE (NC) 03 BLACK - GROUND 04 RED - 12V (+) M5 DATA CABLE COMPATIBLE ACCESSORY M6 01 GREEN/BLACK (NC) 02 BLUE/BLACK (NC) 03 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 10 PURPLE/WHITE (NC) 1 STSW (+) - 04 OR 2 6 5 4 3 10 9 8 7 WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. 4 1 2 3 5 1 6 5 4 3 2 17 16 15 14 13 12 11 10 9 8 7 26 25 24 23 22 21 20 19 18 PARKING LIGHT (-) - 23 5 7.5A 12V (+) - 01 1 IMPORTANT: 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com PAGE 7 OF 17 Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 POLARITY MODULE LOCATION COMPONENT LOCATOR ~ ~ 16 pin 16 Black (DATA) Main body ECU ~ ~ ~ 16 pin 15 White (DATA) Main body ECU ~ STSW ~ ~ 10 pin 04 Black (+) Main body ECU ~ ~ ~ 28 pin 11 Pink (+) Main body ECU ~ 12V ~ ~ 01 pin 01 Yellow (+) Main body ECU ~ Parking light ~ White 20 pin 18 Blue (-) Parking light switch ~ PTS ~ ~ 14 pin 07 White (-) Push button ~ CanH ~ ~ 16 pin 16 Black (DATA) Main body ECU ~ CanL ~ ~ 16 pin 15 White (DATA) Main body ECU ~ STSW ~ ~ 10 pin 04 Black (+) Main body ECU ~ ~ ~ 28 pin 11 Pink (+) Main body ECU ~ 12V ~ ~ 01 pin 01 Yellow (+) Main body ECU ~ Parking light ~ White 20 pin 18 Blue (-) Parking light switch ~ PTS ~ ~ 14 pin 07 White (-) Push button ~ 07-14 Ignition 08-14 Ignition WIRE COLOR CanH CanL CONNECTOR NAME POSITION WIRE DESCRIPTION CONNECTOR TYPE LS600h PTS DOC.: #83971 • 20231127 CONNECTOR COLOR LEXUS LS460 PTS YEAR MODEL MAKE TYPE 2 - WIRE CHART - 1 OF 1 OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com PAGE 8 OF 17 TYPE 2 - WIRING DIAGRAM - 1 OF 1 DOC.: #83971 • 20231127 PTS SWITCH CONNECTIONS ARE REQUIRED 1 ONLY IF IDLE MODE IS DESIRED M1 M2 M6 M3 M4 8 9 10 11 12 13 14 1 2 3 4 5 6 7 PTS (-) - 07 1 M5 DATA 1 M1 01 GRAY/YELLOW (NC) 02 GRAY/RED (NC) 03 GREEN/YELLOW (NC) 04 GREEN/RED (NC) 05 BLUE/YELLOW - PTS (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT MAIN BODY ECU 1 10 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 28 27 26 25 24 23 22 21 IGNITION (+) - 11 M2 01 PINK - IGNITION (+) INPUT 02 PINK/BLACK (NC) 03 ORANGE (NC) 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK (NC) 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 2 4 M3 01 YELLOW (NC) 02 YELLOW/RED (NC) 03 YELLOW/BLACK (NC) 7 1 CANH - 16 16 15 14 13 12 11 6 5 3 1 2 STSW (+) - 04 WITHOUT A COMPATIBLE ACCESSORY M5 01 BLUE/WHITE (NC) 02 WHITE (NC) 03 BLACK - GROUND 04 RED - 12V (+) DATA CABLE 2 8 10 9 M4 01 WHITE - IGNITION (+) INPUT 02 WHITE/RED (NC) 03 WHITE/BLACK - STSW (+) OUTPUT M5 3 CANL - 15 2 1 3 6 5 4 3 10 9 8 7 4 OR COMPATIBLE ACCESSORY WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. 4 7.5A 12V (+) - 01 1 PARKING LIGHT SWITCH M6 01 GREEN/BLACK (NC) 02 BLUE/BLACK (NC) 03 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 10 PURPLE/WHITE (NC) D - WHITE PARKING LIGHT (-) - 18 10 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 IMPORTANT: 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com MODULE PROGRAMMING PROCEDURE - 1 OF 1 >> 01 PAGE 9 OF 17 DOC.: #83971 • 20231127 Between each step, LED will turn solid RED, this is the default standby mode. Push start button twice [2x] to ON position. STOP ACC ON START ENGINE START STOP 02 03 Wait, LED will turn solid GREEN then will turn OFF. Push start button once [1x] to OFF position. STOP ACC ON START ENGINE START STOP 04 Module Programming Procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com AFTERMARKET REMOTE PROGRAMMING PROCEDURE - 1 OF 1 >> 01 02 06 LED 1 will flash GREEN once [1x]. Time restriction. Complete next step within 7 seconds. 07 LED 1 will turn solid RED. Cycle ignition ON five times [5x OFF/ON] rapidly. >> WARNING: Program aftermarket remotes before usage. A maximum of four [4x] aftermarket remotes per system. OFF ACC ON START PAGE 11 OF 17 DOC.: #83971 • 20231127 To program additional remotes: repeat steps 4 to 7 using each additional remote. ENGINE START STOP 03 04 LED 1 will turn solid RED. Time restriction. Complete next step within 2 seconds from previous step. 08 09 Wait, LED 1 will turn OFF. Set ignition to OFF position. OFF ACC ON START ENGINE START STOP 05 Press once [1x] on LOCK button of aftermarket remote. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 10 Aftermarket Remote Programming Procedure completed. OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com PAGE 12 OF 17 MODULE NAVIGATION PROCEDURE - 1 OF 1 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13. >> Module must be programmed to the vehicle. >> 01 Use the Module Navigation Chart on the next page. Set ignition to OFF position. OFF ACC ON START 04 05 TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid RED. [Y] 06 07 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid GREEN. [Z] LED 1 will flash GREEN as many times as the current (or default) setting number, continuously. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will flash GREEN an equal amount of times continuously. DOC.: #83971 • 20231127 10 11 12 13 To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED. [Y] LED 1 will flash RED as many times as the current option number continuously. Configure every other setting and proceed to step 13. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED 1 will flash RED rapidly. Release programming button. LED 1 will turn OFF. ENGINE START STOP 02 03 TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN. [X] IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will flash GREEN an equal amount of times continuously. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 08 09 To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. OEM-AL(RS)-TL3-[ADS-ALCA]-EN 14 >> Module navigation completed. Failure to exit the Module Navigation will drain vehicle battery. www.idatalink.com PAGE 13 OF 17 MODULE NAVIGATION CHART - 1 OF 1 I Default settings are listed in bold. 01 II Make sure the option is covered on the vehicle before attempting to change the setting. 02 03 DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN OFF 02 ON 01 OFF 02 ON 01 OFF 02 ON 01 OFF 02 ON FORCE UNLOCK ALL ON FIRST PRESS 05 N/A 01 N/A 06 N/A 01 N/A 01 DISABLE 02 N/A 03 LOCK + UNLOCK + LOCK 04 LOCK + LOCK + LOCK 01 03 MIN 02 05 MIN 03 10 MIN 04 15 MIN 05 25 MIN 06 30 MIN 07 35 MIN 08 15 MIN 01 02 SEC 02 05 SEC 03 08 SEC 04 10 SEC 05 15 SEC 06 20 SEC 07 25 SEC 08 30 SEC 10-12 N/A 01 N/A 01 01 N/A FACTORY KEYLESS RS SEQUENCE CONFIGURATION 08 09 02-07 Technical Support only 01 04 07 01 [Z] SETTINGS [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES DOC.: #83971 • 20231127 MODULE RUN TIME WAIT TO START DELAY N/A *Vehicle will shutdown when a door is opened. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com REMOTE STARTER ERROR CODES - 1 OF 1 REMOTE STARTER ERROR CODES: NOTES PARKING LIGHT FLASHES PAGE 14 OF 17 DOC.: #83971 • 20231127 DIAGNOSTIC I WARNING: The following applies only when the parking lights are connected and supported by the system. 03 04 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 05 Vehicle failed to remote start. 06 System is in Valet Mode. 07 Vehicle movement detected (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 10 Low fuel level. 11 Emergency brake signal was lost. 12 Door is open. 13 Trunk is open. 14 Vehicle movement detected (VSS). 15 Key is in ignition ON position. 16 CAN communication failure during RS sequence. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 Foot brake is ON. OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 DIAGNOSTIC TEST MODULE LED 1 STATUS MODULE DIAGNOSTICS - 1 OF 1 Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. OEM-AL(RS)-TL3-[ADS-ALCA]-EN PAGE 15 OF 17 DOC.: #83971 • 20231127 www.idatalink.com MODULE RESET PROCEDURE - 1 OF 1 01 02 Disconnect all connectors from module except the BLACK 4-PIN connector. Disconnect the BLACK 4-PIN connector. 03 PRESS AND HOLD programming button while connecting the BLACK 4-PIN connector. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds. 06 Module RESET completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 07 Reconnect all connectors. 08 Repeat programming procedure. >> PAGE 16 OF 17 DOC.: #83971 • 20231127 Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com INSTALLATION CHECKLIST - 1 OF 1 PAGE 17 OF 17 DOC.: #83971 • 20231127 CHECKLIST 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. 14 Exit vehicle. 15 Installation checklist completed. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2023 OEM-AL(RS)-TL3-[ADS-ALCA]-EN www.idatalink.com ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Remote start
- Immobilizer bypass
- Push to start
- OEM alarm integration
- Vehicle customization
- Comprehensive guide
- Step-by-step instructions
- Toyota Land Cruiser 2008 compatible
Frequently asked questions
Refer to the "Aftermarket Remote Programming Procedure" section in the manual for step-by-step instructions on programming additional remotes.
The number of flashes corresponds to an error code. Check the "Remote Starter Error Codes" table to understand the meaning behind the flashes and troubleshoot any issues.
Follow the procedure outlined in the "Module Reset Procedure" section to reset the module. Make sure to disconnect and reconnect all connectors except the black 4-pin connector while holding down the programming button.