Automotive Data Solutions DIR-IDS(RS)-BZ4-[CMBMXA0] Mercedes-Benz ML-Class AMG 2012 Installation Guide
Automotive Data Solutions DIR-IDS(RS)-BZ4-[CMBMXA0] is a remote start system designed for Mercedes-Benz vehicles. It allows you to start your vehicle remotely from a compatible RF kit or telematics device. The system also includes features like secure takeover and immobilizer bypass. The installation guide offers detailed instructions for installing the system in a Mercedes-Benz ML-Class AMG 2012.
PDF
Download
Document
Advertisement
Advertisement
INSTALL GUIDE DIR-IDS(RS)-BZ4-[CMBMXA0]-EN DOCUMENT NUMBER 73852 REVISION DATE 20210202 FIRMWARE DIR-IDS(RS)-BZ4-[CMBMXA0] HARDWARE CMBMXA0 ACCESSORIES ADS-USB (REQUIRED) DIRECTED XL-202 RF-KIT & ADS-HRN(RS)-XL02 (OPTIONAL) DIRECTED SMARTSTART & ADS-HRN(RS)-SM01 (OPTIONAL) TERMS OF USE: Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 BEFORE INSTALLATION 1- Connect module to computer 2- Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately) www.idatastart.com PAGE 2 OF 23 VEHICLE LIST - 1 OF 1 DOC.: #73852 • 20210202 FEATURES YEAR INSTALL TYPE 3X LOCK START/STANDALONE MOD. SECURE TAKEOVER DATA IMMOBILIZER BYPASS ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK TRUNK/HATCH RELEASE PARKING LIGHT CTRL RAP SHUTDOWN CTRL TACHOMETER STATUS MONITORING BRAKE PEDAL STATUS MONITORING VSS STATUS MONITORING GLOW PLUG STATUS MONITORING DOOR STATUS MONITORING TRUNK STATUS MONITORING HOOD STATUS MONITORING* B-Class AT 12-14 1 • • • • • • • • • • • • • • • • • CLA-Class AT 14 1 • • • • • • • • • • • • • • • • • G-Class AT** 13 1 • • • • • • • • • • • • • • • • • G-Class AMG AT** 13 1 • • • • • • • • • • • • • • • • • GL-Class AT** 13 1 • • • • • • • • • • • • • • • • • GL-Class PTS AT** 13 2 • • • • • • • • • • • • • • • • • GL-Class Diesel AT** 13 1 • • • • • • • • • • • • • • • • • GL-Class PTS Diesel AT** 13 2 • • • • • • • • • • • • • • • • • GL-Class AMG AT** 13 1 • • • • • • • • • • • • • • • • • GL-Class AMG PTS AT** 13 2 • • • • • • • • • • • • • • • • • ML-Class AT** 12-13 1 • • • • • • • • • • • • • • • • • ML-Class PTS AT** 12-13 2 • • • • • • • • • • • • • • • • • ML-Class Diesel AT** 12-13 1 • • • • • • • • • • • • • • • • • ML-Class PTS Diesel AT** 12-13 2 • • • • • • • • • • • • • • • • • ML-Class AMG AT** 12-13 1 • • • • • • • • • • • • • • • • • 12-13 2 • • • • • • • • • • • • • • • • • MERCEDES-BENZ MAKE II All the covered Push To Start (PTS) vehicles are equipped with a keyless authorization system called "Keyless Go". ML-Class AMG PTS AT** * If equipped with a factory hood switch. ** 2014 models are NOT covered. The encryption is not the same. Verify VIN before installation. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN POWER LIFTGATE MODEL NOTES I This firmware covers Automatic Transmission (AT) vehicles only. www.idatastart.com PAGE 3 OF 23 BOX CONTENTS - 1 OF 1 DOC.: #73852 • 20210202 BOX CONTENTS MODULE LED 1 LED 2 PROGRAMMING BUTTON USB BLACK BLACK BLACK BLUE 2 4 6 1 3 5 1 2 3 2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 2 4 6 1 3 5 1 2 3 BLACK 1 2 3 4 BLACK RF PORT/WEBLINK PORT AFTERMARKET HOOD SWITCH AND CABLE T-HARNESS 1 4 3 2 1 RED 2 1 BLUE 4 3 2 1 BLACK 4 3 2 1 BLUE TELEMATIC PORT (Accessories sold separately) 10 PIN WHITE CONNECTOR 12 PIN BLACK CONNECTOR 9 10 7 8 5 6 3 4 1 2 WHITE 11 12 9 10 7 8 5 6 3 4 1 2 BLACK 2 PIN BLACK CONNECTOR 2 PIN BLACK CONNECTOR EXPANSION PACK BLACK XP LED 1 XP LED 2 EXTRA CONNECTOR HOUSING 1 2 3 4 EXPANSION PACK ASSEMBLY LED WARNING STICKER LED TOP VIEW 1 3 5 7 9 11 2 4 6 8 10 12 BOTTOM VIEW TOP VIEW WHITE WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com PAGE 4 OF 23 COMPATIBLE ACCESSORIES - 1 OF 1 DOC.: #73852 • 20210202 RF KIT (accessories sold separately) ADS-HRN(RS)-XL02 DIRECTED XL202 RF KIT MODULE RF PORT XL202 RF DECODER XL202 ANTENNA TELEMATIC KIT (accessories sold separately) ADS-HRN(RS)-SM01 DIRECTED SMARTSTART (NC) MODULE TELEMATIC PORT (NC) (NC) Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com TECHNICAL NOTE - 1 OF 1 IMPORTANT PAGE 5 OF 23 DOC.: #73852 • 20210202 INSTALL VIDEO GALLERY AVAILABLE ONLINE Before installing this product, consult our Install Video Gallery and watch: • Vehicle Disassembly Procedure videos • Module Connection Procedures videos • Module Programming Procedures videos Æ To access the videos, simply log in your Weblink user account, and click on "Install videos" under the "Support" tab. Æ Then, select a vehicle make, year and model to display the available videos. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com PAGE 6 OF 23 COMPONENT LOCATOR - 1 OF 1 DOC.: #73852 • 20210202 INTERIOR VIEW DRIVER SIDE VIEW A Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 PASSENGER SIDE VIEW B DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com PAGE 7 OF 23 MODULE INSTALLATION PROCEDURE - 1 OF 1 01 OFF ACC ON START ACC ON START START the vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle. 07 Turn OFF the vehicle. 08 ENGINE START STOP 02 OFF OFF ACC ON START DOC.: #73852 • 20210202 WARNING: Any vehicle harness that is disconnected during installation, must be re-connected before performing any system tests. Failure to comply will result in vehicle displaying error messages. An OEM scantool will be required to clear the error messages. 13 If the vehicle is not equipped with a factory hood switch, install an aftermarket hood switch as shown in STEP 4 of the WIRING DIAGRAM. START the vehicle. Verify all vehicle functionalities. 14 If required, connect a compatible RF Kit to the RF port of the module. RF ENGINE START STOP ENGINE START STOP 03 Verify all keyfob functionalities (Door Lock, Door Unlock, Trunk Release and RFID access if equipped). 09 04 Insert the expansion pack in the module. 10 OFF ACC WARNING: If the vehicle displays error messages or any malfunction, stop the installation, verify every connection and if the problem persists, call technical support. 15 If required, connect a compatible Telematics Device to the TELEMATIC port of the module. Turn OFF the vehicle. 16 Put sticker 1 on a clean and visible surface in the engine bay and put sticker 2 under the dashboard near the OBDII connector. 17 Module installation procedure completed. ON START ENGINE START STOP 05 Connect the module to the computer with the programming cable (WEBLINK port). Flash the module with the latest firmware then flash the expansion pack. 11 Connect every connector to the module, as shown in STEP 2 of the WIRING DIAGRAM. 06 Connect and secure every connector to the vehicle, as shown in STEP 1 of the WIRING DIAGRAM. 12 Connect every other connector to the module, as shown in STEP 3 of the WIRING DIAGRAM. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com PAGE 8 OF 23 TYPE 1 - WIRING DIAGRAM - 1 OF 1 WARNING DOC.: #73852 • 20210202 STEP 1 1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4 2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1 CONNECT TO VEHICLE START VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS BLACK 8 PIN B (VEHICLE HARNESS) MODULE STEP 2 CONNECT TO MODULE IGNITION SWITCH BLACK 8 PIN BLACK 20 PIN RELAY STEP 3 A B BLACK 12 PIN CONNECT TO MODULE BLUE 6 PIN BLACK 12 PIN A (VEHICLE HARNESS) WHITE 12 PIN BLACK 2 PIN (NOT USED) STEP 4 CONNECT IF REQUIRED WHITE 10 PIN IF NOT EQUIPPED WITH AN OEM HOOD SWITCH, INSTALL AN AFTERMARKET HOOD SWITCH HOOD SWITCH 07 GRAY/WHITE - HOOD STATUS (-) INPUT 08 GRAY/BLACK (NOT USED) Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com PAGE 9 OF 23 ML-Class PTS AT ML-Class PTS Diesel AT Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 12-13 12-13 COMPONENT LOCATOR 12-13 MODULE LOCATION ML-Class AMG PTS AT POLARITY 13 WIRE COLOR GL-Class PTS Diesel AT DOC.: #73852 • 20210202 CanH ~ Black 20 pin ~ Brown/Red (DATA) Keyless GO Module, under body panel beside rear left seat. B CanL ~ Black 20 pin ~ Brown (DATA) Keyless GO Module, under body panel beside rear left seat. B POSITION 13 CONNECTOR TYPE GL-Class PTS AT CONNECTOR COLOR 13 CONNECTOR NAME YEAR GL-Class AMG PTS AT WIRE DESCRIPTION MODEL MERCEDES-BENZ MAKE TYPE 2 - WIRE CHART - 1 OF 1 CanH ~ Black 20 pin ~ Brown/Red (DATA) Keyless GO Module, under body panel beside rear left seat. B CanL ~ Black 20 pin ~ Brown (DATA) Keyless GO Module, under body panel beside rear left seat. B CanH ~ Black 20 pin ~ Brown/Red (DATA) Keyless GO Module, under body panel beside rear left seat. B CanL ~ Black 20 pin ~ Brown (DATA) Keyless GO Module, under body panel beside rear left seat. B CanH ~ Black 20 pin ~ Brown/Red (DATA) Keyless GO Module, under rear left seat. A CanL ~ Black 20 pin ~ Brown (DATA) Keyless GO Module, under rear left seat. A CanH ~ Black 20 pin ~ Brown/Red (DATA) Keyless GO Module, under rear left seat. A CanL ~ Black 20 pin ~ Brown (DATA) Keyless GO Module, under rear left seat. A CanH ~ Black 20 pin ~ Brown/Red (DATA) Keyless GO Module, under rear left seat. A CanL ~ Black 20 pin ~ Brown (DATA) Keyless GO Module, under rear left seat. A DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com PAGE 10 OF 23 TYPE 2 - WIRING DIAGRAM - 1 OF 1 WARNING DOC.: #73852 • 20210202 STEP 1 1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4 2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1 CONNECT TO VEHICLE START VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS BLACK 8 PIN B (VEHICLE HARNESS) MODULE STEP 2 CONNECT TO MODULE IGNITION SWITCH BLACK 8 PIN BLACK 20 PIN RELAY STEP 3 A B BLACK 12 PIN CONNECT TO MODULE BLUE 6 PIN BLACK 12 PIN A (VEHICLE HARNESS) WHITE 12 PIN CONNECTIONS INSTRUCTIONS ON NEXT PAGE REFER TO WIRE CHART AND COMPONENT LOCATOR KEYLESS GO MODULE CONNECT 01 PINK/RED - CANH 02 PINK/BLACK - CANL BLACK 2 PIN (NOT USED) CONNECT STEP 4 A CONNECT IF REQUIRED WHITE 10 PIN IF NOT EQUIPPED WITH AN OEM HOOD SWITCH, INSTALL AN AFTERMARKET HOOD SWITCH HOOD SWITCH 07 GRAY/WHITE - HOOD STATUS (-) INPUT 08 GRAY/BLACK (NOT USED) Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com TYPE 2 - WIRING DIAGRAM - 2 OF 2 PAGE 11 OF 23 DOC.: #73852 • 20210202 INSTRUCTIONS TO CONNECT CAN WIRES TO KEYLESS GO MODULE KEYLESS GO MODULE 1- DISCONNECT BLACK CONNECTOR FROM KEYLESS GO MODULE (A) A CONNECTOR A 5- INSERT VEHICLE CAN WIRES IN PROVIDED HOUSING TO INSULATE THEM 2- REMOVE VEHICLE CANH WIRE (BROWN/RED) AND CANL WIRE (BROWN) FROM CONNECTOR (A) 3- INSERT CANH WIRE (PINK/RED) AND CANL WIRE (PINK/BLACK) FROM PROVIDED HARNESS INTO VEHICLE CONNECTOR (A) CONNECTOR A KEYLESS GO MODULE 4- RECONNECT BLACK CONNECTOR INTO KEYLESS GO MODULE (A) A Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com MODULE PROGRAMMING PROCEDURE - STD KEY - 1 OF 1 01 LED 1 is solid RED. Insert key into ignition. ACC ACC START OFF Turn key to ON position. ACC ON 03 Wait, LED 1 will turn solid GREEN then will turn solid RED. >> WARNING: If LED 1 flashes RED/GREEN, turn ignition to OFF position. The vehicle is PTS. Follow appropriate PTS sections. ACC OFF 05 07 ON START Module Programming Procedure completed. START OFF 04 Turn key to OFF position. Remove key from ignition. ON OFF 02 06 PAGE 12 OF 23 DOC.: #73852 • 20210202 ON START START vehicle for 30 seconds. LED 1 will remain solid RED. Wait, LED 1 will turn solid GREEN then will turn OFF. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com MODULE PROGRAMMING PROCEDURE - PTS - 1 OF 1 01 STOP ACC ON START LED 1 is solid RED. Push start button to ON position. 07 ENGINE START STOP Wait, LED 1 will flash RED/GREEN. 03 Disconnect the 2 PIN Keyless GO connector from T-harness. The vehicle parking lights will begin to flash. 04 Reconnect the 2 PIN Keyless GO connector to T-harness. LED 1 will turn solid RED. The vehicle parking lights will stop flashing. STOP ACC ON START Push start button to OFF position. STOP ACC ON START ENGINE START STOP 02 05 PAGE 13 OF 23 DOC.: #73852 • 20210202 08 Module Programming Procedure completed. START vehicle for 30 seconds. LED 1 will remain solid RED. ENGINE START STOP 06 Wait, LED 1 will turn solid GREEN then will turn OFF. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 01 Time restriction. Complete next step within 7 seconds. 02 OFF ACC ON START >> PAGE 14 OF 23 DOC.: #73852 • 20210202 To exit valet mode: repeat steps 1 to 4 then START vehicle for 15 seconds. Cycle ignition ON five times [5x OFF/ON] rapidly. Parking Light will flash once [1x]. ENGINE START STOP 03 04 Wait, Parking Light will flash twice [2x], pause for 1.5 second, then will flash once [1x] to indicate that the valet mode is ON or twice [2x] to indicate that the valet mode is OFF. Turn ignition to OFF position. OFF ACC ON START ENGINE START STOP 05 Valet Mode Programming Procedure completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com AFTERMARKET REMOTE PROGRAMMING - 1 OF 1 PAGE 15 OF 23 DOC.: #73852 • 20210202 AFTERMARKET REMOTE PROGRAMMING: NOTES I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com PAGE 16 OF 23 MODULE NAVIGATION PROCEDURE - 1 OF 1 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13. 04 >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will flash GREEN an equal amount of times continuously. 09 01 OFF ACC ON START DOC.: #73852 • 20210202 TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid RED. 10 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will flash RED an equal amount of times continuously. 11 TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid GREEN. 12 Configure every other setting and proceed to step 13. [Z] LED 1 will flash GREEN as many times as the current (or default) setting number, continuously. 13 MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED 1 will flash RED rapidly. Release programming button. LED 1 will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will flash GREEN an equal amount of times continuously. 14 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED. [Y] LED 1 will flash RED as many times as the current option number continuously. ENGINE START STOP 02 03 [X] Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com PAGE 17 OF 23 MODULE NAVIGATION CHART - 1 OF 1 I Default settings are listed in bold. 01 OFF 02 ON 01 OFF 02 ON 01 OFF 02 ON 01 OFF 02 ON 01 ENABLE 02 DISABLE* 01 45 SEC 02 90 SEC 03 03 MIN 04 04 MIN 01 DISABLE 02 N/A 03 LOCK + UNLOCK + LOCK 04 LOCK + LOCK + LOCK 01 03 MIN 02 05 MIN 03 10 MIN 04 15 MIN 05 25 MIN 06 30 MIN 07 35 MIN 08 15 MIN 01 02 SEC 02 05 SEC 03 08 SEC 04 10 SEC 05 15 SEC 06 20 SEC 07 25 SEC 08 30 SEC 10-15 N/A 01 N/A 01 01 N/A 01 II Make sure the option is covered on the vehicle before attempting to change the setting. 02 03 04 05 06 07 01 [Z] SETTINGS [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS TAKEOVER SECURE TAKEOVER DELAY FACTORY KEYLESS RS SEQUENCE CONFIGURATION 08 09 02-07 Technical Support only DOC.: #73852 • 20210202 MODULE RUN TIME WAIT TO START DELAY N/A *Vehicle will shutdown when a door is opened. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES - 1 OF 1 I WARNING: The following applies only when the parking lights are connected and supported by the system. 03 Foot brake is ON. 04 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 10 N/A 11 N/A 12 N/A 13 N/A 14 N/A 15 N/A 16 CAN communication failure during RS sequence. REMOTE STARTER ERROR CODES: NOTES Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN PAGE 18 OF 23 DOC.: #73852 • 20210202 www.idatastart.com I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIAGNOSTIC TEST MODULE LED 1 STATUS MODULE DIAGNOSTICS - 1 OF 1 Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. DIR-IDS(RS)-BZ4-[CMBMXA0]-EN PAGE 19 OF 23 DOC.: #73852 • 20210202 www.idatastart.com MODULE RESET PROCEDURE - 1 OF 1 01 Disconnect all connectors from module except the BLACK 20-PIN connector. 07 Reconnect all connectors. 02 Disconnect the BLACK 20-PIN connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module’s programming button while connecting the BLACK 20-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds. 06 Module RESET completed. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN PAGE 20 OF 23 DOC.: #73852 • 20210202 www.idatastart.com TAKEOVER PROCEDURE - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. The vehicle can be remote started up to 5 times between normal key or push button start operation. 06 Press and release BRAKE pedal. 01 Time restriction. Complete steps 2 to 6 within 45 seconds. 07 Take over procedure completed. 02 Unlock driver door. >> Failure to follow procedure will result in vehicle engine shutdown. 03 Open driver door and enter vehicle. 04 Close driver door. 05 OFF ACC ON START PAGE 21 OF 23 DOC.: #73852 • 20210202 Push start button once [1x] to ON position OR turn key to ON position. ENGINE START STOP Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com INSTALLATION CHECKLIST - 1 OF 2 PAGE 22 OF 23 DOC.: #73852 • 20210202 CHECKLIST 01 WARNING: Vehicle engine will start many times. Test in a well ventillated area. 02 Open driver door window for easy vehicle access. 03 Enter vehicle. Start the vehicle and let it run for 15 seconds. 04 Stop the vehicle and exit vehicle. 05 Close all vehicle doors, hood and trunk. 06 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. QUESTION 1: Does the vehicle remote start? ¨ ¨ YES: Go to step 7. 07 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat step 6 and call technical support if the problem persists. QUESTION 2: Does the vehicle shut down? ¨ ¨ YES: Go to step 8. 08 Open hood. NO: Repeat step 7. If the problem persists, unlock the door using the OEM keyfob, enter vehicle and press brake pedal to shut down the vehicle and call technical support. QUESTION 3: Is the orange warning sticker "Sticker 1" placed under the hood? ¨ ¨ YES: Leave hood open and go to step 9. 09 Close all doors. 10 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. NO: Put the mandatory orange warning sticker "Sticker 1", leave hood open and go to step 9. QUESTION 4: Does the vehicle remote start? ¨ ¨ YES: Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Go to question 5. NO: Go to step 11. QUESTION 5: Is the vehicle equipped with a factory hood switch? (Inside hood latch) ¨ ¨ YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support. 11 Close hood. 12 Enter vehicle. Do NOT press brake pedal. 13 Close all doors. 14 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 15 Wait for the vehicle to start. 16 Press brake pedal. NO: Install the mandatory hood switch included in the kit. Repeat installation checklist. QUESTION 6: Does the vehicle shut down? ¨ ¨ YES: Go to step 17. NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com INSTALLATION CHECKLIST - 2 OF 2 PAGE 23 OF 23 DOC.: #73852 • 20210202 CHECKLIST 17 Exit vehicle. 18 Close all doors. 19 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 20 Wait for the vehicle to start. QUESTION 7: Is the vehicle equipped with a keyless authorization system (Keyless Go) ? ¨ ¨ YES: Touch the exterior driver door handle to unlock door using the keyless authorization system (Keyless Go). Within 45 seconds, go to step 21. 21 Open driver door. NO: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 21. QUESTION 8: Does the vehicle shut down? ¨ ¨ YES: The module does NOT detect the unlock signal from the vehicle communication network. Call technical support. 22 Enter vehicle. NO: Go to step 22. QUESTION 9: Is the vehicle equipped with a keyless authorization system (Keyless Go) ? ¨ ¨ YES: Push vehicle start button once [1x]. Go to step 23. 23 Press and release brake pedal. NO: Insert key into ignition and turn key to ON position. Go to step 23. QUESTION 10: Does the vehicle shut down? ¨ ¨ YES: Repeat this procedure from step 3. If the problem persists, call technical support. 24 Shut down the vehicle. 25 Installation checklist completed. NO: Go to step 24. Patent No. US 8,856,780 CA 2759622 Automotive Data Solutions Inc. © 2021 DIR-IDS(RS)-BZ4-[CMBMXA0]-EN www.idatastart.com ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Remote Start
- Secure Takeover
- Immobilizer Bypass
- OEM Alarm Integration
- Door Lock/Unlock
- Trunk Release
- Parking Light Control
- Hood Status Monitoring
Frequently asked questions
This specific installation guide covers Mercedes-Benz ML-Class AMG models from 2012. It's important to verify compatibility with other models through the provided vehicle list.
No, this firmware only covers automatic transmission (AT) vehicles.
The ADS-USB programming cable is required. You can also use optional RF kits like the DIRECTED XL-202 RF-KIT & ADS-HRN(RS)-XL02 or telematics kits like DIRECTED SMARTSTART & ADS-HRN(RS)-SM01.