Instruction Manual
Register your product at
www.babystyledirect.co.uk
CONTENTS
Important Safety Information
Fitting and Removing of Front Wheels
Fitting and Removing of Rear Wheels
Locking and Unlocking the Front Swivel Wheels
Opening the Chassis with the Seat Unit Fitted
Folding the Chassis with the Seat Unit Fitted
Folding the Chassis with the Seat Unit / Carrycot / Car Seat Removed
Adjusting the Handle Height
Using the Parking Brake
Fitting / Removing the Bumper Bar
Fitting the Seat Unit
Removing the Seat Unit
Adjusting the Seat Unit Backrest
Adjusting the Leg Rest
Hood / Sun Canopy
Adjusting the Hood / Canopy / Harness Shoulder Height
Using the Restraint System
Fitting the Stroller Rain Cover
Assembling the Carrycot
Fitting the Carrycot Apron
Fitting the Carrycot to the Chassis
Removing the Carrycot
Adjusting the Carrycot Hood
Rocking / Stablising the Carrycot when not attached to the Chassis
Fitting the Carrycot Rain Cover
Fitting the Footmuff
Fitting the Oyster Carapace Infant Car Seat using the Multi Adaptors
Removing the Oyster Carapace Infant Car Seat from
the Chassis when fitted with the Multi Adaptors
Care and Maintenance
Your Warranty Policy
Notes
PAGE
4-5
6
6
7
7-8
9-10
10
11
11
11
12
12
12
13
13-15
15
15-16
17
17
17
18
19
19
19
20
20
20-21
21
23
24-25
26-27
3
IMPORTANT – Read these instructions before use
and keep for future reference.
Important Safety Information.
This vehicle is intended for children from birth to a maximum of 22kg.
Age and weight usage: Pram body/carrycot 0 to 9Kg, Car seat 0 to 13kg (follow
manufacturers guidelines), Seat unit 0 to 22kg, Ride on board/platform max 20kg.
The seat unit, carrycot or car seat is suitable for one child only to the maximum
weight stated above.
It is important that any person intending to use this stroller understands the
instructions.
WARNING: Never leave your child unattended.
WARNING: Ensure that all locking devices are engaged before use.
WARNING: To avoid injury ensure that the child is kept away when
unfolding and folding this product.
WARNING: Do not let the child play with this product.
WARNING: Always use the restraint system (safety harness).
WARNING: Check the pram body, seat unit or car seat attachment
devices are correctly engaged before use.
WARNING: This product is not suitable for running or skating.
WARNING: The maximum weight for the shopping basket is 3kg.
WARNING: Never lift/carry the chassis while occupied. Your child’s safety
may be at risk.
4
WARNING: Do not use the vehicle on steps, stairs or escalators; as it
may be dangerous to your child.
WARNING: Always descend/mount kerbs on the back wheels, do not tip
the stroller forward.
WARNING: Any load attached to the handle and/or the back of the
backrest and/or the sides of the vehicle will affect the stability of the
vehicle.
WARNING: Incorrect assembly, folding or use of this vehicle may cause
damage and affect the safety of the stroller.
WARNING: Pram body/carrycot: This product is suitable for a child who
cannot sit up unaided, roll over and cannot push itself up on its hands and
knees. Maximum weight of the child for the carrycot must not exceed 9kg.
WARNING: Always use the seat in the most reclined position for new born
babies to approx. 6 months.
WARNING: Always use the crotch strap in combination with the waist belt.
WARNING: Never leave the stroller without first engaging the parking
device. Avoid uphill or downhill parking.
WARNING: No additional mattress should be added to the carrycot;
only use the mattress provided.
WARNING: Never use the parasol attached to the stroller if there is wind.
WARNING: Do not use accessories that are not approved by the
manufacturer.
WARNING: Do not use replacement parts other than those supplied by
the manufacturer or supplier.
5
All references to left and right are given from
the perspective of a person standing in the
pushing position.
FITTING AND REMOVING
OF FRONT WHEELS
PUSH
Ensure the swivel lock under the support bar
between the front wheels is in the unlock position
(see section 4).
1
1. Push the wheel unit onto the front wheel axle
stub until it clicks into position.
2. To remove the wheel; push in the quick release
button on the back of the front wheel joint and
pull the wheel away from the axle.
PUSH
BUTTON
2
FITTING AND REMOVING
OF REAR WHEELS
3. Press and hold the button in the centre of the
rear wheel and push the wheel into the rear wheel
housing; release the button and the wheel should
lock in position.
To remove; press and hold the button in the centre
of the rear wheel and pull the wheel away from the
wheel housing.
6
PRESS
AND
HOLD
3
LOCKING AND UNLOCKING THE
FRONT SWIVEL WHEELS
4. Push the switch left or right under the support
bar between the front wheels to lock or unlock the
swivel wheels. When locked the front wheels will
not be able to swivel and this may help when
travelling over uneven surfaces (e.g cobblestones).
PUSH
LEFT OR
RIGHT
4
OPENING THE CHASSIS WITH THE
SEAT UNIT FITTED
WARNING: To avoid injury ensure that
children are kept away when unfolding and
folding this product.
5. Place the chassis in the free standing position.
5
6. Ensure that the brake is applied. Stand behind
the stroller so that the chassis locking clip is on the
left hand side. Release the chassis locking clip by
pulling the clip away from the frame.
PULL
CLIP
6
7
OPENING THE CHASSIS WITH THE
SEAT UNIT FITTED (CONT)
LIFT
HANDLE
7. Lift the handle until it clicks into its correct
position.
7
8. Continue to bring the handle towards you until
the rear wheels come into contact with the floor.
Push down on the handle and the chassis will fully
open and lock into position.
8
9. Lift up backrest until seat unit clicks into
position. Pull down the leg rest so it locks into
position. Adjust the bumper bar so that it locks
into position.
WARNING: Ensure the locking devices are
engaged before use.
9
8
FOLDING THE CHASSIS WITH THE
SEAT UNIT FITTED
WARNING: Ensure the child is well clear of
moving parts and all items are removed from
the shopping basket.
The stroller will fold with the seat unit both forward
facing & rearward facing.
10
10. To fold the chassis with the seat unit rearward
facing: Apply the brake. Hold the leg rest, lift lever
on the seat back and bring down the seat-back to
meet the foot rest. When the backrest and leg rest
meet, rotate the whole seat unit to the front of the
stroller.
11. While standing in the push position,
simultaneously pull back the sliders on each side
of the chassis.
PULL
BACK
11
12. Push the handle away from you all the way
down to the front wheels.
PUSH
HANDLE
12
9
FOLDING THE CHASSIS WITH THE
SEAT UNIT FITTED (CONT)
13
LIFT
13. Pull the carry handle upwards to fold the
chassis. Squeeze the chassis together if required
so that the chassis locking clip locks into place.
The folded chassis can now free-stand or lie flat.
To fold the chassis with the seat unit forward
facing: Apply the rear brake. Lift the lever on the
seat back. Push the seat-back forward and the
bumper bar and leg rest will automatically collapse
to the front of the stroller. While standing in the
push position, simultaneously pull back the sliders
on each side of the chassis and push the handle
away from you so that it rotates forward all the way
to the front wheels. Locate the carry handle
positioned on the bottom of the seat unit. Pull the
carry handle upwards to fold the chassis. Squeeze
the chassis together if required so that the chassis
locking clip locks into place. The folded chassis
can now free-stand or lie flat.
HOLD
AND
LIFT
14
FOLDING THE CHASSIS WITH THE
SEAT UNIT / CARRYCOT / CAR SEAT
REMOVED
Apply the brake, while standing in the push
position, simultaneously pull back the sliders on
each side of the chassis; lift and push the handle
away from you and gently lower down towards the
front wheels.
14. Hold the chassis with hands left and right at
the central attachment device.
15
15. Lift and the rear legs will swing in and the
chassis will close and lock.
10
ADJUSTING THE HANDLE HEIGHT
16. The handle height is adjustable to four
positions. To adjust the handle height, hold in the
button in the middle of the handle grip, slide the
handle up or down to one of the four positions.
The handle will click into one of the pre-set
positions when the button is released.
SLIDE
16
USING THE PARKING BRAKE
17. To engage the brake, firmly press down on the
brake lever found in the middle of the rear axle.
Check that the brake is fully engaged before
letting go of the handle. To release the brake,
press forwards or lift up the brake lever until the
wheel moves freely.
PRESS
DOWN /
LIFT UP
WARNING: Never leave the stroller without
first engaging the brake.
17
WARNING: Always ensure that the parking
brake is applied when placing and removing
children.
FITTING / REMOVING THE BUMPER
BAR
18
PUSH
18. Push both ends of the bumper bar into the
corresponding entry slots on the seat unit until the
bumper bar locks into position. To remove the
bumper bar, press in the bumper bar release
buttons on either side underneath the entry slots
on the seat unit.
11
FITTING THE SEAT UNIT
19. Align the seat attachments into the central
hubs on either side of the chassis.
Push down until the seat unit clicks and locks into
position. Ensure the seat unit is locked in position
by trying to pull the seat from the chassis. The seat
unit can be fitted facing forwards or rearwards.
ALIGN
19
REMOVING THE SEAT UNIT
20. Gently hold the seat unit at the top of the
back rest and with your other hand locate the
handle under the seat padding, pull forwards and
lift up. This will release the seat from the
attachment device.
PULL
FORWARDS
AND LIFT UP
20
ADJUSTING THE SEAT UNIT BACKREST
21. Pull the lever at the top rear of the backrest to
recline the seat backrest. The seat backrest has
three pre-set positions. When the seat backrest is
in the required position, release the lever and the
seat will lock into position. To move the seat
backrest from any of the reclined positions simply
push/lift the seat backrest without using the seat
recline lever.
21
12
ADJUSTING THE LEG REST
22. To lower the leg rest press in the buttons on
both sides at the top of the leg rest and push
down. To raise the leg rest into higher positions,
lift the leg rest and it will automatically click into
the next position.
PRESS
22
23. The leg rest also has a pop up feature to raise
the calf support. Push up from beneath the calf
support until it pops into position.
23
There is a small zipped pocket under the footrest.
PUSH
HOOD/SUN CANOPY
24. The seat unit has a multi-function hood that
helps to protect your child from the elements. The
hood is extendable, factor 50+ protected and has
a peekaboo ventilation window as well as a flip out
sun visor.
24
13
HOOD/SUN CANOPY (CONT)
UNZIP
25. To extend the hood unzip the zip across the
centre of the hood to get the full extension.
25
26. To utilise the peekaboo ventilation window
fold over the fabric of the panel nearest the back
rest.
FOLD
26
27. The sun visor is neatly folded inside the front
of the hood. Simply reach in and pull the visor and
it will spring forward into position. The visor is
attached by zip if you wish to remove or reattach.
PULL
27
14
HOOD/SUN CANOPY (CONT)
28. The hood can be removed altogether by
simply pushing up on the round fittings on either
side at the bottom of the hood.
LIFT
28
ADJUSTING THE HOOD / CANOPY /
HARNESS SHOULDER HEIGHT
29. Push in the buttons on both sides at the base
of the hood. Whilst the buttons are pressed, lift to
raise the height of the hood/canopy or lower to
reduce the height of the hood/canopy. When the
buttons are released the hood will automatically
click into one of four pre-set positions.
PRESS
29
USING THE RESTRAINT SYSTEM
30. Always apply the parking brake before placing
your child in the vehicle.
30
SHOULDER
STRAP AND
BUCKLE
The restraint system (safety harness) has two
shoulder straps, a circular waist belt and a crotch
strap.
CROTCH
STRAP AND
BUCKLE
WAIST
BELT AND
BUCKLE
CENTRAL
BUCKLE
15
USING THE RESTRAINT SYSTEM
(CONT)
31. Place the two shoulder straps over the child’s
shoulder and the waist belt around the waist. The
crotch strap should be placed between the child’s
legs. To secure: fit together the left connector from
the shoulder strap with the left connector from the
waist belt.
31
32. Push firmly into the central buckle. Repeat,
fitting the right connector from the shoulder strap
with the right connector from the waist belt and
again firmly push into the central buckle.
The harness can be adjusted to suit your child by
sliding the adjusters along the shoulder straps and
waist belt. To release the safety harness, push the
button in the centre of the buckle. The crotch
strap can be adjusted to suit your child. There are
two button holes in the seat base. Thread the
buckle through the hole in the plastic seat base
then through the opening in the seat covers and
reposition, passing back through first the seat
cover and then through the opening in the plastic
seat base.
WARNING: Ensure the buckle and
connectors are fully engaged before use.
WARNING: Always use the crotch strap in
combination with the waist belt.
ALWAYS USE THE SAFETY HARNESS
16
32
FITTING THE STROLLER RAIN COVER
33
33. To fit the stroller rain cover the hood needs to
fully extended. Unfold and place the rain cover so
that it covers all the textile parts. Pull the
elasticated bottom of the rain cover over the leg
support. To secure the rain cover fasten the press
stud on the strap around the back of the backrest.
CARRYCOT
WARNING: This product is only suitable for a
child who cannot sit up unaided.
WARNING: Only use on a firm, horizontal
level and dry surface.
PULL
ASSEMBLING THE CARRYCOT
PULL
34. Remove the apron and mattress. Unzip the
lining to gain access to the stay bars in the bottom
of the carrycot. Using the three webbing tabs; pull
the stay bars into position so that they are against
the small plastic bumps on the baseboard. Zip up
the lining, replace the mattress and refit the apron.
34
FITTING THE CARRYCOT APRON
35. Fasten the zip on the apron to the
corresponding zip on the carrycot and pull all the
way around. Secure the press studs between the
apron and carrycot.
FASTEN
ZIP
35
17
FITTING THE CARRYCOT TO
THE CHASSIS
36. The carrycot can only be fitted to the chassis
when the seat unit has been removed. The
carrycot can only be fitted to the chassis facing the
parent. Lower the carrycot into the attachment
devices left and right. Push down until the carrycot
clicks and locks into position. Check the carrycot is
securely attached by trying to lift the carrycot from
the chassis.
WARNING: Carrycot can not be fitted
forward facing.
WARNING: Use only on a firm, horizontal
level and dry surface.
WARNING: Do not use if any part of the
carrycot is broken, torn or missing.
WARNING: No additional mattress shall be
added unless recommended by the
manufacturer.
WARNING: Do not place the carry cot near
an open fire or other source of strong heat.
WARNING: Do not let other children play
unattended near the carrycot.
WARNING: The handles and the bottom of
the carrycot should be inspected regularly
for signs of damage and wear.
18
ALIGN
36
REMOVING THE CARRYCOT
37. Hold the carrycot using the handle at the front
of the hood. While holding this, pull the handle
situated at the back of the carrycot and lift. The
carrycot will release from the chassis.
37
WARNING: Before carrying or lifting, make
sure that the handle is in the correct locked
position.
WARNING: The head of the child in the
carry cot should never be lower than the
body of the child.
38
ADJUSTING THE CARRYCOT HOOD
38. Press in the buttons on the sides of the hood
and pull up until you hear them click into place.
Press in the buttons again to put the hood down.
PRESS
ROCKING / STABILISING THE
CARRYCOT WHEN NOT ATTACHED
TO THE CHASSIS
39
39. The carrycot is designed to be able to rock
gently when placed on the floor and not attached
to the chassis. There are four pop out feet under
the carrycot which can be pulled out to stabilise
the carrycot in a secure position.
FEET
FEET
19
FITTING THE CARRYCOT RAIN COVER
40. Fully extend the hood. Unfold and place the
rain cover over the hood of the carrycot so that
the flap on the rain cover corresponds with the
opening in the in the carrycot hood. Pull the rain
cover down at the rear of the hood so that the
elasticated edge covers the rear of the carrycot.
Ease the front part of the rain cover over the apron
and down around the front and sides of carrycot.
Fasten press studs below attachment device.
40
FITTING THE FOOTMUFF
41. Release the harness clips from the centre
buckle. Fit the footmuff over the head rest
padding and pass through the shoulder straps.
Pass the waist belts through the corresponding
slots in the footmuff. Pass the crotch strap through
the slot in the footmuff. Fold the flap of the top
cover over the bumper bar. The footmuff top cover
can be removed by unfastening the zip. The base
of the footmuff can be used as a seat liner without
the top cover.
FITTING THE OYSTER CAPSULE
INFANT CAR SEAT USING THE MULTI
ADAPTORS
42. The car seat can not be attached to the chassis
until the seat unit or carrycot has been removed.
The multi adaptors fit many leading brands of car
seats (check with your retailer for full details). Insert
the car seat adaptors into the chassis attachment
devices. The adaptors and chassis attachment
devices are marked with an ‘L’ and ‘R’ to represent
left and right from the perspective of you being in
the pushing position.
20
41
ALIGN
AND
PUSH
DOWN
42
FITTING THE OYSTER CAPSULE
INFANT CAR SEAT USING THE MULTI
ADAPTORS (CONT)
43. Hold the car seat by the carry handle and
lower the car seat onto the multi adaptors, the
adaptors should slot into the cavity at the base of
the car seat handle left & right. Push down the car
seat firmly until the car seat clicks and locks into
position. Check that the car seat is secure and
locked by pulling up on the car seat handle.
WARNING: For car seats used in
conjunction with the chassis, these car seats
do not replace a cot or bed.
WARNING: Should your child need to sleep,
then they should be placed in a suitable
pram body, cot or bed.
ALIGN
AND
PUSH
DOWN
43
PRESS
DOWN
AND LIFT
REMOVING THE OYSTER CAPSULE
INFANT CAR SEAT FROM THE CHASSIS
WHEN FITTED WITH THE MULTI
ADAPTORS
44
44. To remove the car seat from the chassis: Press
down on the two buttons on the sides of the car
seat and lift the car seat away from the chassis
45
45. To remove the adaptors form the chassis push
in the buttons on the bottom of the adaptors and
lift the adaptors away from the attachment device.
PRESS
AND LIFT
21
22
CARE AND MAINTENANCE
• Regularly check screws, rivets, bolts and fastenings to ensure they are locked tight and
secure. Replace any parts in an inferior condition. When using this product during the
winter, by the sea or off road it is important to clean using fresh water and dry
thoroughly. Salt water and salt and grit from the roads will corrode metal parts unless
removed.
• Check on a regular basis that all chassis locking devices are working correctly.
• If any part of the product is damaged, contact your local BabyStyle retailer immediately
without using the pushchair.
• Do not expose the product to excessive sunlight for periods of time, even normal
exposure to sunlight may cause change to the colour of the fabrics.
• Take care not to tear fabrics when transporting the stroller.
• Light oil or silicone spray can be used to lubricate moving parts. Periodically remove the
rear wheels; clean, lubricate and replace.
• Ensure all zips are either fully open or closed to prevent damage.
• Always use the rain cover in inclement weather.
• Do not place items on top of the hood/canopy, it could damage the fabrics or render
the product unsafe.
• Any load attached to the handle and/or on the back of the backrest and/or on the sides
of the stroller will affect the stability of the stroller.
• Tyres can leave marks on some surfaces such as vinyl flooring or carpet.
• Fabrics should only be cleaned in accordance to the care labels.
• Do not place fabrics in a washing machine, hand wash or sponge clean only using mild
detergent and warm water (30°C)
23
WARRANTY POLICY
KEEP YOUR ORIGINAL RECEIPT OF PURCHASE SAFE WITH YOUR
WARRANTY INFORMATION
It will be required should you unfortunately find a defect. The receipt must show the date
of purchase clearly. In the first instance you must contact the original place of purchase.
Exchanging or returning the product cannot be requested. Repairs to any part of this
product do not extend the warranty period. Do not return your product direct to the
manufacturer.
SERVICING OF YOUR OYSTER 3 STROLLER
We recommend that this product is regularly maintained and is serviced by a BabyStyle
authorised dealer at least every 12 months. Only replacement parts supplied or
recommended by the manufacturer/distributor shall be used.
DISCLAIMER
Whilst we believe the information set out in this instruction manual to be correct and
reliable at the time of print, we do not accept responsibility for its accuracy and we shall
not be liable for its interpretation and its use. We reserve the right to change, modify, add
or delete product specifications at any time without prior notice.
YOUR WARRANTY POLICY
At BabyStyle, we guarantee your product has been manufactured in accordance with all
current European safety standards which are applicable to this product, and that this
product is free from any defects in workmanship and material at the time of purchase.
During the production process this product has gone through rigorous quality checks.
Despite our efforts, if this product does show a manufacturing or material defect within the
24 months warranty period for the chassis and seat frames and 6 months for the carrycot,
seat fabrics and PVC rain cover, we will comply to the warranty terms and conditions
providing the product has been used for normal use as described within the instruction
manual and it has been serviced and maintained correctly as described in the instruction
manual, for further information please contact the place of purchase. Please retain your
original receipt of purchase safely.
24
WARRANTY TERMS
• Chassis and seat frames: 24 consecutive months.
• Seat fabrics, carrycot, accessories and PVC rain cover: 6 consecutive months.
• The warranty only applies to the original purchaser and is non-transferable.
The warranty will be invalidated in the following circumstances:
• The product has not been used for its purpose other than described within the
instruction manual.
• If the product is returned for repair through a dealer not authorised by us.
• If the original receipt of purchase cannot be provided.
• If the defect is as a result of improper use or incorrect maintenance, negligence or
impact damage.
• If the parts show normal wear and tear that may be expected from daily use of the
product (wheels, rotating or moving parts etc).
The warranty of this product becomes valid from the date of purchase as stated on the
original receipt of purchase. This does not affect your statutory rights.
25
NOTES
26
27
36 Charles Street, Sileby,
Leicestershire LE12 7RJ.
T: 01509 816444
E: [email protected]
www.babystyle.co.uk
©BabyStyle UK Ltd 2018 JM1425/04012021v4
">
