Now classified in accordance with ANSI/SIA CP-01-2000 (SIA-FAR)
Programming Worksheets
PC1555 CP-01
PC1555 CP-01 version 3.2
DLS2002 and higher
Page references below are to the accompanying Installation Manual. The programming sections are in numeric order in the present publication.
PC1555 CP-01 Programming Guidelines
Item
Page
Section
Zone Programming
Item
Partition Account Numbers
Page
Section
31
[311]
App . A
[320]-[349]
Zone Definitions
20
[001]-[002]
Reporting Codes
Zone Attributes
29
[101]-[132]
Communicator Format Options
34
[350]
Communicator Call Direction
36
[351]-[376]
Adding Hardwire Zones
Residential Dial
Assigning Zones to Zone Expanders
7
2.6
Assigning Zones to System
30
[202]-[205]
First, Second, Third Phone Numbers
31
[301]-[303]
Zone Definitions
20
[001]-[002]
Call Waiting Cancel String
31
[304]
Zone Attributes
29
[101]-[132]
System Account Number
31
[310]
Partition Account Numbers
31
[311]
App . A
[320]-[349]
Adding Wireless Zones
Enrolling Wireless Serial Numbers
PC5132 Manual [804]
Reporting Codes
Assigning Zones to System
30
[202]-[205]
Communicator Format Options
34
[350]
Zone Definitions
20
[001]-[002]
Communicator Call Direction
36
[351]-[376]
Zone Attributes
29
[101]-[132]
Test Transmission
App . A
[348]
Keypad Assignment
7
[000]
Communication Variables
36
[377]
Keypad Zone Assignment
29
[020]
Test Transmission Time of Day
37
[378]
Assigning Zones to System
30
[202]-[205]
Sixth System Option Code, Option [1]
27
[018]
Wiring Keypad Zones
10
2.11
Telephone Line Monitoring (TLM)
Third System Option Code, Options [7, 8]
25
[015]
Programmable Output Options
22
[009]
Communication Variables
36
[377]
Priority Alarm/Restore Reporting Codes
31
[329]
Reporting Codes
App . A
[345, 364]
Zone Wiring - 2 Wire Smoke Detectors
8
2.10
PGM Outputs
PGM1 and PGM2 Outputs
22
[009]
Cross Zoning / Police Zone Select Option [6]
28
[018]
PGM3 to PGM10 Outputs
22
[010]
Zone Attributes
29
[101]-[132]
PGM11 to PGM14 Outputs
22
[011]
Cross Zone / Police Code Timer
30
[176]
PGM Output Attributes
41
[501]-[515]
Miscellaneous Alarm Reporting Codes
31
[328]
PGM System Assignment
45
[551]-[564]
[401]
Adding Keypad Zones
Test Transmission Reporting Codes
2 Wire Smoke Detectors
Cross Zones
Local System
Downloading
Communicator Enabled/Disabled
37
[380]
First Downloading Option Code
41
Third System Option Code, Option [7]
25
[015]
Downloading Computer Phone Number
41
[402]
Downloading Access Code
41
[403]
SIA Communications
First, Second, Third Phone Numbers
31
[301]-[304]
Panel Identification Code
41
[404]
Call Waiting Cancel String
31
[304]
Double Call Timer
41
[405]
System Account Code
31
[310]
Number of Rings to Answer
41
[406]
Partition Account Number
31
[311]
Bell Output Options
System Times
21
[005]
First System Option Code, Option [8]
24
[013]
24
[014]
App . A
[320]-[349]
Communicator Format Options
Reporting Codes
34
[350]
Communicator Call Direction
36
[351]-[376]
Second System Option Code, Options [1]-[5]
First, Second, Third Communicator Options
37
[380]-[382]
Automatic Arming
Automatic Arming Schedule
30
[181]
First, Second, Third Phone Numbers
31
[301]-[303]
Postpone Auto Arming Timer
29
[175]
Call Waiting Cancel String
31
[304]
Auto-Arming Pre-Alert
30
[199]
System Account Number
31
[310]
Fifth System Option Code, Option [1]
26
[017]
Partition Account Number
31
[311]
No Activity Arming
No Activity Arming Timers
30
[191]
No Activity Arming Pre-Alert
30
[190]
44
[801]-[851]
44
[901]-[999]
Contact ID Communications
App . A
[320]-[349]
Communicator Format Options
Reporting Codes
34
[350]
Communicator Call Direction
36
[351]-[376]
Module Programming
First, Second, Third Communicator Options
37
[380]-[382]
Module Programming
Pager
Special Installer Functions
First, Second, Third Phone Numbers
31
[301]-[303]
Call Waiting Cancel String
31
[304]
System Account Number
31
[310]
Special Installer Functions
Table of Contents
Section 1: For the Record
1
Account Information .......................................................... 1
[377] Communication Variables ........................................ 15
Zone Programming Summary ............................................. 2
LINKS1000 Preambles ....................................................... 16
Section 2: Keypad Programming
3
Communicator Options..................................................... 16
Section 7: Downloading Options
17
Section 3: Basic Programming
4
Zone Definitions ................................................................. 4
Section 8: Programmable Output Programming
18
Programmable Output Attributes ...................................... 18
System Times and Codes .................................................... 5
PGM Output Assignment .................................................. 19
Programmable Output Options ........................................... 5
Section 9: International Programming
20
Keypad Zone Assignments.................................................. 7
Section 10: Module Programming
21
Zone Loop Response Option Code...................................... 7
Section 11: Special Installer Functions
21
Other System Options......................................................... 5
Section 4: Advanced System Programming
8
Zone Attributes .................................................................. 8
System Timers .................................................................... 9
Appendix A: Programming LCD5500Z/LCD5520Z Keypads
22
LCD5500Zv2.x and Lower Keypads ................................... 22
Automatic Arming Schedule ............................................. 10
ASCII Characters .............................................................. 24
Section 5: Partition and Zone Programming
10
Assigning Zones to the System ......................................... 10
LCD5500Z/LCD5520Z v3.x and Higher Keypads ................ 24
ASCII Characters .............................................................. 27
Section 6: Communicator Programming
11
Telephone Numbers ......................................................... 11
Appendix B: Programming LCD5501Z Keypads
28
Programming Keypad Options........................................... 28
[350] Communicator Format Options ............................... 14
Programming Door Chime Options ................................... 28
Call Direction Options....................................................... 14
ii
Section 1: For the Record
Account Information
Customer:___________________________________________________________________________________________________
Address:____________________________________________________________________________________________________
Telephone:______________________________________________Installation Date:_____________________________________
Installer’s Code:______________________________________________________________________________________________
Module and Keypad Information
Module Name
Description
Location
PC1555 CP-01
Main Panel
I________________________________________________________________________________________________________________I
PC5132
Wireless Receiver 1
I________________________________________________________________________________________________________________I
PC5132
Wireless Receiver 2
I________________________________________________________________________________________________________________I
PC5132
Wireless Receiver 3
I________________________________________________________________________________________________________________I
PC5132
Wireless Receiver 4
I________________________________________________________________________________________________________________I
PC5200
Power Supply Module 1
I________________________________________________________________________________________________________________I
PC5200
Power Supply Module 2
I________________________________________________________________________________________________________________I
PC5200
Power Supply Module 3
I________________________________________________________________________________________________________________I
PC5200
Power Supply Module 4
I________________________________________________________________________________________________________________I
PC5204
Power Supply Output Module
I________________________________________________________________________________________________________________I
PC5208
Low-Current Output Module
I________________________________________________________________________________________________________________I
PC5936
Audio Interface Module
I________________________________________________________________________________________________________________I
Escort5580
Voice Prompt Module
I________________________________________________________________________________________________________________I
PC5400
Serial Printer Module
I________________________________________________________________________________________________________________I
PC5400
DVACS* Module
I________________________________________________________________________________________________________________I
LINKS1000
Cellular Communicator
I________________________________________________________________________________________________________________I
LINKS2X50
Long Range Radio
I________________________________________________________________________________________________________________I
Skyroute
Transceiver
I________________________________________________________________________________________________________________I
Keypads
Keypad Type
Location
Keypad 1
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 2
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 3
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 4
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 5
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 6
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 7
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 8
I_____________________________________________I
I________________________________________________________________________________________________________________I
*DVACS is a registered trademark of Electro Arts Limited
1
Zone Programming Summary
Zone programming can be found in sections [001] - [002], [101] - [132], [020] and [202] - [205]. Use this area to record a summary of your zone programming. Refer to, for instructions on programming zone labels.
System
Zone Label
Zone
Zone
Zone Attributes*
Type
1 2 3 4 5 6 7 8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
*Zone Attributes:
Option 1: Audible/Silent
Option 2: Steady/Pulsed
Option 3: Chime
Option 4: Bypass
2
Option 5: Force Arming
Option 6: Swinger Shutdown
Option 7: Transmission Delay
Option 8: Wireless
Option 9: Cross Zone
Serial Number
9
(Wireless)
Section 2: Keypad Programming
[000] Keypad Enrollment
NOTE: This must be done at each keypad requiring programming.
[0] Slot address [Valid entries are 0-1 for the partition, 1-8 for the slot. (e.g., to enroll a keypad in Partition 1 and slot 1, enter (11)]
[1] Function Key 1 Assignment (Valid entries are 00-32)
[2] Function Key 2 Assignment (Valid entries are 00-32)
[3] Function Key 3 Assignment (Valid entries are 00-32)
[4] Function Key 4 Assignment (Valid entries are 00-32)
[5] Function Key 5 Assignment (Valid entries are 00-32)
Function Key Options:
00 Not used
11 [*][5] Access Code Programming
22 For Future Use
01 Select Partition 1
12 [*][6] User Functions
23 Bypass Recall
02 For Future Use
13 Command Output #1 [*][7][1]
24 Recall Bypass Group
03 Stay Arm
14 Command Output #2 [*][7][2]/Sensor Reset
25 For Future Use
04 Away Arm
15 General Voice Prompted Help
26 For Future Use
05 [*][9] No-Entry Arm
16 [*][0] Quick Exit
06 [*][4] Chime On / Off
17 [*][1] Reactivate Stay/Away Zones
07 [*][6][——][4] System Test
18 Identified Voice Prompted Help
08 [*][1] Bypass Mode
19 Command Output 3 [*][7][3]
09 [*][2] Trouble Display
20 For Future Use
10 [*][3] Alarm Memory
21 Command Output 4 [*][7][4]
Partition/
Slot
LCD 5501/LED defaults11
LCD Defaults
18
Function
Key 1
03
03
Function
Key 2
04
04
Function
Key 3
06
06
Function
Key 4
14
14
Function
Key 5
16
16
KEYPAD 1
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 2
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 3
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 4
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 5
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 6
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 7
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 8
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
3
Section 3: Basic Programming
Zone Definitions
00
01
02
03
04
05
06
07
08
09
10
11
Null Zone (Not Used)
Delay 1*
Delay 2*
Instant*
Interior*
Interior, Stay/Away*
Delay, Stay/Away*
Delayed 24 Hour Fire (Hardwired)**
Standard 24 Hour Fire (Hardwired)
24 Hour Supervisory
24 Hour Supervisory Buzzer*
24 Hour Burglary*
12
13
14
15
16
17
18
19
20
21
22
24 Hour Holdup*
24 Hour Gas*
24 Hour Heating*
24 Hour Auxiliary*
24 Hour Panic*
24 Hour Emergency*
24 Hour Sprinkler*
24 Hour Water*
24 Hour Freeze*
24 Hour Latching Tamper*
Momentary Keyswitch Arm*
23 Maintained Keyswitch Arm*
24 LINKS1000 Answer*
25 Interior Delay*
26 24 Hour Non-alarm*
27 Delayed 24 Hour Waterflow
28 Instant 24 Hour Waterflow
29 Auto Verified Fire
30 Fire Supervisory
31 Day Zone*
87 Delay 24 Hour Fire (Wireless)**
88 Standard 24 Hour Fire (Wireless)**
*For burglary applications only
** For residential fire applications only
NOTE: To use 24-hour Buzzer zones, keypads must be installed .
NOTE: Keypad zones are assigned in section [020]. Zone Attributes are assigned in sections [101] - [132]. Zone assignment is
in sections [202] - [205].
Section #
Zone #
Default
Zone
Defn.
[001]
01
01
I_____I_____I
02
03
I_____I_____I
03
03
I_____I_____I
04
03
I_____I_____I
05
04
I_____I_____I
06
04
I_____I_____I
07
04
I_____I_____I
08
04
I_____I_____I
09
00
I_____I_____I
10
00
I_____I_____I
11
00
I_____I_____I
12
00
I_____I_____I
13
00
I_____I_____I
14
00
I_____I_____I
15
00
I_____I_____I
16
00
I_____I_____I
17
00
I_____I_____I
18
00
I_____I_____I
19
00
I_____I_____I
20
00
I_____I_____I
21
00
I_____I_____I
22
00
I_____I_____I
23
00
I_____I_____I
24
00
I_____I_____I
25
00
I_____I_____I
26
00
I_____I_____I
27
00
I_____I_____I
28
00
I_____I_____I
29
00
I_____I_____I
30
00
I_____I_____I
31
00
I_____I_____I
32
00
I_____I_____I
[002]
4
Basic Programming:
System Times and Codes
[005] System Times
NOTE: Valid entries for Entry Delay is between 030-240, valid entries for Exit Delay is between 045-255.
[01] Entry/Exit times
I___I___I___I
Entry Delay 1
030
I___I___I___I
Entry Delay 2
030
I___I___I___I
Exit Delay
060
[006] Installer’s Code
Default
I_______I_______I_______I_______I
5555
[007] Master Code
Default
1234
I_______I_______I_______I_______I
[008] Maintenance Code
Default
AAAA
I_______I_______I_______I_______I
Programmable Output Options
01
02
03
04
05
06
07
08
09
10
11
12
13
Residential Burglary and Fire Bell Output
For Future Use
Sensor Reset [*][7][2]
2 Wire Smoke Support (PGM 2 only)
System Armed Status
Ready To Arm
Keypad Buzzer Follow Mode
Courtesy Pulse
System Trouble Output (with Trouble options)
System Event [Strobe (with Event options)]
System Tamper (all sources: zones, keypad, modules)
TLM and Alarm
Kissoff Output
14
15
16
17
18
19
20
21
22
23
24
25
Ground Start Pulse
Remote Operation (DLS2002 Support)
LINKS1000 Support (PGM1 only)
Away Armed Status
Stay Armed Status
Command Output #1 ([*][7][1])
Command Output #2 ([*][7][2])
Command Output #3 ([*][7][3])
Command Output #4 ([*][7][4])
24 Hour Silent Input
24 Hour Audible Input
Delayed Fire and Burglary Output
NOTE: Output types [03] and [20] cannot be used together on the same system.
[009] PGM1 and PGM2 Output Programming (Main Panel)
NOTE: Program PGM Option Attributes in sections [501] - [514]. Program PGM System Assignment in sections [551] - [564].
Default
Default
PGM 1
10
19
I_______I_______I
I_______I_______I PGM 2
[010] PGM3 to PGM10 Output Programming (Main Panel/PC5208)
NOTE: Program PGM Option Attributes in sections [501] - [514]. Program PGM System Assignment in sections [551] - [564].
Default
Default
01
PGM 3 (main panel/PC5208)*
01
PGM 7 (PC5208)
I_______I_______I
I_______I_______I
01
PGM 4 (main panel/PC5208)*
01
PGM 8 (PC5208)
I_______I_______I
I_______I_______I
01
PGM 5 (PC5208)
01
PGM 9 (PC5208)
I_______I_______I
I_______I_______I
01
PGM 6 (PC5208)
01
PGM 10 (PC5208)
I_______I_______I
I_______I_______I
NOTE: These two sections allow you to program the first two PGM outputs on the PC5208.
[011] PGM11 to PGM14 Output Programming (PC5204)
NOTE: Program PGM Option Attributes in sections [501] - [514]. Program PGM System Assignment in sections [551] - [564]
Default
01
I_______I_______I
PGM 11
Default
01
I_______I_______I
PGM 13
01
I_______I_______I
PGM 12
01
I_______I_______I
PGM 14
Other System Options
[012] Keypad Lockout Options
NOTE: If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch.
Default
000
I_______I_______I_______I
Number of Invalid Codes Before Lockout (001-255 codes)
000
I_______I_______I_______I
Lockout Duration (001-255 minutes)
5
[013] First System Option Code
Default
Option
ON
OFF I________I
1
Normally Closed Loops
OFF
End-of-Line Resistors
OFF
I________I
2
Double End-of-Line Resistors
Single End-of-Line Resistors
ON*
I________I
3
Panel shows all troubles when armed
Panel shows only Fire troubles when armed
OFF
I________I
4
Tampers/Faults do not show as open
Tampers/Faults show as open
ON
I________I
5
Auto-arm Schedule in [*][6]
Auto-arm Schedule in Installer Programming Only
ON
I________I
6
Audible Exit Fault Enabled
Audible Exit Fault Disabled
ON
I________I
7
Event Buffer Follows Swinger Shutdown Event Buffer Logs Events Past shutdown
OFF
I________I
8
Temporal Three Fire Signal Enabled
Standard Pulsed Fire Signal
* Option 3 must be OFF if LCD keypads older than v2.0 are used.
[014] Second System Option Code
Default
Option
ON
OFF I________I
1
Arm / Disarm Bell Squawk enabled
OFF
Arm / Disarm Bell Squawk disabled
OFF
I________I
2
Bell Squawk During Auto Arm
No Bell Squawk During Auto Arm
OFF
I________I
3
Bell Squawk On Exit Delay
No Bell Squawk On Exit Delay
OFF
I________I
4
Bell Squawk On Entry Delay
No Bell Squawk On Entry Delay
OFF
I________I
5
Bell Squawk On Trouble
No Bell Squawk On Trouble
ON
I________I
6
Audible Exit with Urgency
Silent Exit Delay
OFF
I________I
7
Exit Delay Termination Enabled
Exit Delay Termination Disabled
OFF
I________I
8
Residential Fire Bell is Continuous
Residential Fire Bell Follows Bell Cut-off
[015] Third System Option Code
Default
Option
ON
ON I________I
1
Fire Keys Enabled
OFF
Fire Keys Disabled
OFF
I________I
2
Panic Keys Audible (Bell / Beeps)
Panic Keys Silent
OFF
I________I
3
Quick Exit Enabled
Quick Exit Disabled
ON*
I________I
4
Quick Arming Enabled/
Function keys do not require code
Quick Arming Disabled/
Function keys require code
OFF**
I________I
5
Code Required For Bypassing
No Code Required
OFF
I________I
6
Master Code Not Changeable
Master Code Changeable
ON
I________I
7
TLM Enabled
TLM Disabled
OFF
I________I
8
TLM Audible (Bell) When Armed
TLM Trouble Beeps When Armed
* When using a PC5132 version 2.1 or older with the WLS909 Wireless Key, Option [4] must be ON for the Arm button to work.
**If option [5] is ON, function keys programmed as [08] Bypass will require an access code when used, even if option [4] is also on.
[016] Fourth System Option Code
Default
Option
ON
ON I________I 1
AC Trouble Displayed
OFF I________I 2
Trouble Light Flashes if AC Fails
Blank Keypad When Not Used
OFF I________I 3
Code Required to Remove Keypad Blanking
OFF I________I 4
ON I________I 5
Keypad Backlighting is enabled
Power Save Mode enabled
OFF I________I 6
Bypass Status Displayed While Armed
OFF I________I 7
OFF I________I 8
Keypad Tampers enabled
6
OFF
AC Trouble Not Displayed
Trouble Light Does Not Follow AC Status
Keypad Active Always
No Code Required
Keypad Backlighting is disabled
Power Save Mode disabled
Bypass Status Not Displayed While Armed
Keypad Tampers disabled
Basic Programming
[017] Fifth System Option Code
Default
Option ON
I________I
1
WLS Key Does Not Use Access Codes*
ON
I________I
2
RF Jam Log After 5 Minutes
OFF
I________I
3
Audible RF Jam Trouble Beeps
OFF
OFF
I________I
4
Double Hit Enabled
I________I
5
Late to Close Enabled
OFF
I________I
6
Daylight Savings Time Enabled
OFF
ON
I________I
7
For Future Use
8
Squawk on Away Key Arming/Disarming Only
OFF I________I
OFF
WLS Key Uses Access Codes
RF Jam Log After 30 Seconds
Silent RF Trouble Jam Beeps
Double Hit Disabled
Late to Close Disabled
Daylight Savings Time Disabled
For Future Use
Bell Squawk on all Arming/Disarming‡
*This option must be enabled when using a PC5132 v2.1 or earlier. / ‡This option is supplemental to Section 14 Option 1
[018] Sixth System Option Code
Default
Option
ON
OFF
OFF I________I
1
Test Transmission Exception Enabled
Test Transmission Exception Disabled
2
Verbal Chime Enabled
Verbal Chime Disabled
OFF I________I
OFF I________I
3
Verbal Alarm Enabled
Verbal Alarm Disabled
4
Water-Flow Silence Inhibit Enabled
Water-Flow Silence Inhibit Disabled
OFF I________I
5
Keypad Buzzer Follows Bell Enabled
Keypad Buzzer Follows Bell Disabled
OFF I________I
OFF I________I
6
Cross Zoning Enabled
Cross Zoning Disabled
7
Exit Delay Restart Enabled
Exit Delay Restart Disabled
ON I________I
8
AC Trouble Beeps Enabled
AC Trouble Beeps Disabled
OFF I________I
NOTE: For Cross Zoning to function, Option[6] in Section [018] and Option [9] in Section [101]-[132] must be ON for the desired
zone. Each zone has the ability to protect the intended area. Cross Zoning is not recommended for line security installations or on
exit/entry zone types.
Keypad Zone Assignments
[020] Keypad Zone Assignments
NOTE: Only one keypad may be assigned to a zone.
Default
00
00
00
00
00
00
00
00
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
Keypad (slot 1) Zone
Keypad (slot 2) Zone
Keypad (slot 3) Zone
Keypad (slot 4) Zone
Keypad (slot 5) Zone
Keypad (slot 6) Zone
Keypad (slot 7) Zone
Keypad (slot 8) Zone
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Zone Loop Response Option Code
[030] Sixth System Option Code
Default
Option
ON
1
Zone 1 is Fast Loop Response
OFF I________I
2
Zone 2 is Fast Loop Response
OFF I________I
OFF I________I
3
Zone 3 is Fast Loop Response
OFF I________I
4
Zone 4 is Fast Loop Response
OFF I________I
5
Zone 5 is Fast Loop Response
6
Zone 6 is Fast Loop Response
OFF I________I
OFF I________I
7
For Future Use
OFF I________I
8
For Future Use
OFF
Zone 1 is Normal Loop Response
Zone 2 is Normal Loop Response
Zone 3 is Normal Loop Response
Zone 4 is Normal Loop Response
Zone 5 is Normal Loop Response
Zone 6 is Normal Loop Response
7
Section 4: Advanced System Programming
Zone Attributes
Zone Attribute Defaults (Y = Option ON; N = Option OFF):
Attribute:
ON
OFF
Zone Type:
00 Null Zone
01 Delay 1
02 Delay 2
03 Instant
04 Interior
05 Int. Stay/Away
06 Dly. Stay/Away
07 Dly. 24hr Fire (Hardw.)
08 Stand. 24hr Fire (Hardw.)
09 24hr Superv.
10 24hr Superv. Buzzer
11 24hr Burglary
12 24hr Holdup
13 24hr Gas
14 24hr Heating
15 24hr Medical
16 24hr Panic
17 24hr Emergency
18 24hr Sprinkler
19 24hr Water
20 24hr Freeze
21 24hr Latching Tamper
22 Momentary Keyswitch
23 Maintained Keyswitch
24 LINKS Answer
25 Interior Delay
26 24hr Non-alarm
27 Delayed 24hr Waterflow
28 Instant 24hr Waterflow
29 Auto Verified Fire
30 Fire Supervisory
31 Day Zone
87 Dly. 24hr Fire (Wireless)
88 Stand. 24hr Fire (Wireless)
Section
Zone #
Zone
Type**
1
2
3
4
5
6
7
8
9
Audible
Silent
Steady
Pulsed
Chime
No
Bypass
No
Force
No
Swing
No
Tx. Delay
No
Wireless Zn
No
Cross Zn
No
N
Y
Y
Y
Y
Y
Y
Y
Y
N
N
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
Y
N
Y
Y
Y
N
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
N
N
Y
Y
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
N
N
N
Y
N
N
N
N
N
Y
N
N
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
N
N
Y
N
N
N
N
N
N
N
Y
Y
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
Y
N
N
N
N
Y
N
N
N
Y
Y
Y
Y
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
Y
N
N
N
N
N
Y
N
N
N
Y
Y
Y
Y
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
Y
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Audible/
Silent
1
Steady/
Pulsed
2
Chime
No
3
Bypass
No
4
Force
No
5
Swing
No
6
Tx. Delay
No
7
Wireless
No
8
Cross Zn
No
9
[101]
01
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________|
[102]
02
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[103]
03
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[104]
04
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[105]
05
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[106]
06
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[107]
07
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[108]
08
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[109]
09
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[110]
10
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[111]
11
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[112]
12
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[113]
13
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[114]
14
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
8
Advanced System Programming:
Section
Zone #
Zone
Type**
Audible/
Silent
1
Steady/
Pulsed
2
Chime
No
3
Bypass
No
4
Force
No
5
Swing
No
6
Tx. Delay
No
7
Wireless
No
8
Cross Zn
No
9
[115]
15
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[116]
16
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[117]
17
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[118]
18
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[119]
19
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[120]
20
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[121]
21
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[122]
22
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[123]
23
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[124]
24
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[125]
25
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[126]
26
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[127]
27
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[128]
28
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[129]
29
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[130]
30
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[131]
31
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[132]
32
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
**Record here based on programming in sections [001] - [002]
System Timers
[165] Maximum Dialing Attempts to Each Telephone Number
Default: 007
I_______I_______I_______I
Valid entries are 001-015 attempts (do not enter 000).
[166] Post Dial Wait for Handshake (All Formats)
Default: 040
I_______I_______I_______I
Valid entries are 001-255 seconds
[167] T-LINK Interface Communications Wait for Acknowledge
Default: 020
I_______I_______I_______I
Valid entries are 001-255 seconds
[170] PGM Output Timer
Default: 005
I_______I_______I_______I
Valid entries are 001-255 seconds
[175] Auto-arm Postpone Timer
Default: 000
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 allows automatic arming to be cancelled
[176] Cross Zone/Police Code Timer
Default: 060
I_______I_______I_______I
Valid entries are 001-255 seconds/minutes
NOTE: The total delay time (combination of control plus waterflow device) for a waterflow zone alarm is not to exceed 120 seconds.
[177] Waterflow Delay Timer
Default: 000
I_______I_______I_______I
Valid entries are 000-090 seconds
[178] Alarm Tone Verified for Verbal Alarm
Default: 015
I_______I_______I_______I
Valid entries are 001-255 seconds
9
Automatic Arming Schedule
Enter a four-digit number (HH:MM) for each day that the system will Auto-arm. All entries are disabled (9999) by default. Valid
entries are 0000-2359.
Section #
Day of the
Week
Time of Day
[181]
Sunday
I_______I_______I:I_______I_______I
Monday
I_______I_______I:I_______I_______I
Tuesday
I_______I_______I:I_______I_______I
Wednesday
I_______I_______I:I_______I_______I
Thursday
I_______I_______I:I_______I_______I
Friday
I_______I_______I:I_______I_______I
Saturday
I_______I_______I:I_______I_______I
[190] No Activity Arming Pre-Alert Time
Default
001
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 for no pre-alert
No Activity Arming Timers
Section
[191]
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
NOTE: Default is [000].
[199] Auto-arming Pre-Alert Timer
Valid entries are 001-255 minutes
Default: 005 I_______I_______I_______I
Section 5: Partition and Zone
Programming
Assigning Zones to the System
Program which zones will be assigned to the system in sections [202] to [205]. Program zone definitions in sections [001] - [002]
and zone attributes in sections [101] - [132]. Program keypad zone assignments in section [020].
NOTE: By default, zones 1 through 6 are assigned to the system. All other zones are not assigned to the system.
ON = Assigned to system; OFF = Not assigned to system
Section
[202]
[203]
[204]
[205]
10
Zone:
01
02
03
04
05
06
07
08
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
09
10
11
12
13
14
15
16
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
17
18
19
20
21
22
23
24
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
25
26
27
28
29
30
31
32
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
Section 6: Communicator
Programming
Telephone Numbers
NOTE: For sections [301] to [353], the content of every section by default is [F].
[301] First Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[302] Second Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[303] Third Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[304] Call Waiting Cancel String (6 Digits)
I_______I_______I_______I_______I_______I_______I Default = DB70EF Program unused digits with Hex F
NOTE: All six digits must be entered for changes to be saved. Fill unused digit spaces with ‘F’
NOTE: When using T-Link, program DCAA as the phone number.
Account Codes
Enter a six-digit account number for the system account code. Only SIA supports six digit account codes. If the last two digits of
the account code are FF, the panel will only use the first four digits.
Section
[310]
System Account Code
I_______I_______I_______I_______I_______I_______I
Enter a 4-digit account number for active partition.
Section
Partition Account Code
I_______I_______I_______I_______I
[311]
Reporting Codes
Alarm Reporting Codes, Zones 01-32
Note: All reporting codes are defaulted to FF.
Section
[320]
Zone 01
Zone 02
Zone 03
I_______I_______I
[321]
I_______I_______I
I_______I_______I
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Alarm Restoral Reporting Codes, Zones 01-32
Section
[324]
Zone 01
Zone 02
Zone 03
I_______I_______I
[325]
Zone 04
I_______I_______I
I_______I_______I
I_______I_______I
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
11
[328] Miscellaneous Alarm Reporting Codes
I_______I_______I Duress Alarm
I_______I_______I Opening After Alarm
I_______I_______I Recent Closing
I_______I_______I Zone Expander Supervisory Alarm
I_______I_______I Zone Expander Supervisory Restore
I_______I_______I Cross Zone Police Code Alarm
I_______I_______I Burglary Not Verified
I_______I_______I Alarm Cancelled
[329] Priority Alarm and Restoral
I_______I_______I Keypad Fire Alarm
I_______I_______I
Keypad Auxiliary Alarm
I_______I_______I
Keypad Panic Alarm
I_______I_______I
Auxiliary Input Alarm
I_______I_______I
Keypad Fire Restoral
I_______I_______I
Keypad Auxiliary Restoral
I_______I_______I
Keypad Panic Restoral
I_______I_______I
Auxiliary Input Restore
Tamper Reporting Codes, Zones 01-32
Section
[330]
Zone 01
Zone 02
Zone 03
[331]
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Tamper Restoral Reporting Codes, Zones 01-32
Section
[334]
Zone 01
Zone 02
Zone 03
[335]
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______II
[338] Miscellaneous Tamper Reporting Codes
I_______I_______I General System Tamper
I_______I_______I
General System Tamper Rest.
I_______I_______I
Keypad Lockout
Closing (Arming) Reporting Codes, Access Codes 1-32
Section
[339]
Code 1
Code 2
Code 3
Code 4
[340]
12
I_______I_______I
Code 5
Code 6
Code 7
Code 8
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 9
Code 10
Code 11
Code 12
Code 13
Code 14
Code 15
Code 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 17
Code 18
Code 19
Code 20
Code 21
Code 22
Code 23
Code 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 25
Code 26
Code 27
Code 28
Code 29
Code 30
Code 31
Code 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Communicator Programming:
[341] Miscellaneous Closing (Arming) Reporting Codes
I_______I_______I Closing by Duress Code 33
I_______I_______I
Closing by Duress Code 34
I_______I_______I
Closing by Master Code 40
I_______I_______I
Closing by Supervisory Code 41
I_______I_______I
Closing by Supervisory Code 42
I_______I_______I
Partial Closing
I_______I_______I
Special Closing
I_______I_______I
Late to Close
I_______I_______I
Exit Fault
Opening (Disarming) Reporting Codes, Access Codes 1-32
Section
[342]
Code 1
Code 2
Code 3
Code 4
I_______I_______I
[343]
I_______I_______I
I_______I_______I
I_______I_______I
Code 5
Code 6
Code 7
Code 8
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 9
Code 10
Code 11
Code 12
Code 13
Code 14
Code 15
Code 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 17
Code 18
Code 19
Code 20
Code 21
Code 22
Code 23
Code 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 25
Code 26
Code 27
Code 28
Code 29
Code 30
Code 31
Code 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
[344] Miscellaneous Opening (Disarming) Reporting Codes
I_______I_______I
Opening by Duress Code 33
I_______I_______I
Opening by Duress Code 34
I_______I_______I
Opening by Master Code 40
I_______I_______I
Opening by Supervisory Code 41
I_______I_______I
Opening by Supervisory Code 42
I_______I_______I
Auto Arm Cancellation
I_______I_______I
Special Opening
[345] Maintenance Alarm Reporting Codes
I_______I_______I Battery Trouble Alarm
I_______I_______I
AC Failure Trouble Alarm
I_______I_______I
Bell Circuit Trouble Alarm
I_______I_______I
Fire Trouble Alarm
I_______I_______I
Auxiliary Power Supply Trouble Alarm
I_______I_______I
TLM Trouble Code (via LINKS)
I_______I_______I
General System Trouble
I_______I_______I
General System Supervisory
[346] Maintenance Restoral Reporting Codes
I_______I_______I Battery Trouble Restoral
I_______I_______I
AC Failure Trouble Restoral
I_______I_______I
Bell Circuit Trouble Restoral
I_______I_______I
Fire Trouble Restoral
I_______I_______I
Auxiliary Power Supply Trouble Restoral
I_______I_______I
TLM Restoral
I_______I_______I
General System Trouble Restore
I_______I_______I
General System Supervisory Restore
13
[347] Miscellaneous Maintenance Reporting Codes
I_______I_______I Telephone Number 1 FTC Restore
I_______I_______I
Telephone Number 2 FTC Restore
I_______I_______I
Event Buffer 75% Full Since Last Upload
I_______I_______I
DLS Lead IN
I_______I_______I
DLS Lead OUT
I_______I_______I
Zone Fault Alarm
I_______I_______I
Zone Fault Restore
I_______I_______I
Delinquency Code
I_______I_______I
General Zone Low Battery Alarm
I_______I_______I
General Zone Low Battery Restoral
I_______I_______I
Installer Lead Out
I_______I_______I
Installer Lead In
[348] Test Transmission Reporting Codes
I_______I_______I Walk Test End
I_______I_______I
Walk Begin
I_______I_______I
Periodic Test Transmission with Trouble
I_______I_______I
Periodic Test Transmission
I_______I_______I
System Test
I_______I_______I
LINKS1000 Test Transmission Code*
*The LINKS1000 Test Transmission Code must be programmed as “00” for the LINKS1000 Test Transmission to be disabled.
[350] Communicator Format Options
NOTE:The Third telephone number follows the format of the First telephone number.
Default
04 I_______I_______I
04
I_______I_______I
1st/3rd Telephone Number
2nd Telephone Number
01 20 BPS, 1400 HZ handshake
02 20 BPS, 2300 HZ handshake
03 DTMF CONTACT ID
04 SIA FSK
05 Pager
06 Residential Dial
07 10 BPS, 1400Hz handshake
08 10 BPS, 2300Hz handshake
Call Direction Options
Alarm/Restore Communicator Call Directions
Section
Option:
Defaults:
[351]
1
1st Telephone
Number
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
6,7,8
For
Future
Use
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE: The LINKS1000 backup call directions will only back up their respective telephone numbers.
Tamper/Restore Communicator Call Directions
Section
Option:
Defaults:
[359]
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE: The LINKS1000 backup call directions will only back up their respective telephone numbers.
14
6,7,8
For
Future
Use
1
1st Telephone
Number
Communicator Programming:
Opening/Closing Communicator Call Directions
Section
Option:
1
1st Telephone
Number
Defaults:
[367]
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
6,7,8
For
Future
Use
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE: The LINKS1000 backup call directions will only back up their respective telephone numbers.
System Maintenance Communicator Call Directions
Section
Option:
Defaults:
[375]
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
6,7,8
For
Future
Use
1
1st Telephone
Number
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE: The LINKS1000 backup call directions will only back up their respective telephone numbers.
System Test Transmissions Communicator Call Directions
Section
Option:
Defaults:
[376]
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
6,7,8
For
Future
Use
1
1st Telephone
Number
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE: The LINKS1000 backup call directions will follow the programming in Sections 351-376, above.
[377] Communication Variables
Default
001
I_______I_______I_______I
Swinger Shutdown (Alarms and Rest)
(001-002 Transmissions)
003
I_______I_______I_______I
Swinger Shutdown (Tampers and Rest)
(001-014 Transmissions, 000=disabled)
003
I_______I_______I_______I
Swinger Shutdown (Maint and Rest)
(001-014 Transmissions, 000=disabled)
030
I_______I_______I_______I
Communication Delay
(015-045 seconds)
030
I_______I_______I_______I
AC Failure Communication Delay
(001-255 minutes)
003
I_______I_______I_______I
TLM Trouble Delay
(No. of checks required - valid entries 003 - 255)
030
I_______I_______I_______I
Test Transmission Cycle (land line)
(001-255 days/minutes)†
030
I_______I_______I_______I
Test Transmission Cycle (LINKS1000)
(001-255 days)
007
I_______I_______I_______I
Zone Low Battery Transmission Delay
(000-255 days)
030
I_______I_______I_______I
Delinquency Transmission Cycle
(000-255 days/hours)
005
I_______I_______I_______I
Communications Cancelled Window
(000-255 minutes)
†Depends on programming in section [702], option [3].
NOTE: For UL installations, the entry delay plus Communication Delay time will not be programmed to exceed 60 seconds.
NOTE: To disable the AC failure communications delay, program [000]. This does not apply to Central and Remote Fire applications.
15
[378] Test Transmission Time of Day
Default
Valid entries are 0000-2359, 9999 to disable)
I_______I_______I_______I_______I
9999
NOTE: Do not enter [9999] for Central and Remote Fire Applications.
Communicator Options
[380] First Communicator Option Code
Default
Option
ON
ON I_______I
1
Communications Enabled
OFF
Communications Disabled
OFF
I_______I
2
Restorals on Bell Time-out
Restorals Follow Zones
OFF
I_______I
3
Pulse Dialing
DTMF Dialing
OFF
I_______I
4
Switch to Pulse Dialing on 5th Attempt
DTMF Dial For All Attempts
OFF
I_______I
5
3rd Telephone Number enabled
3rd Telephone Number disabled
OFF
I_______I
6
Alternate Dial (1st and 3rd)
Call 1st Number, Backup to 3rd
OFF
I_______I
7
Call LINKS as well as Land Line
LINKS is Backup of Land Line(s)
OFF
I_______I
8
Delinquency Follows Zone Activity (Hours)
Delinquency Follows Arming (Days)
[381] Second Communicator Option Code
Default
Option ON
OFF I_______I
1
Open After Alarm Kypd Ringback enabled
OFF
Open After Alrm Kypd Ringback disabled
OFF
I_______I
2
Open After Alarm Bell Ringback enabled
Open After Alrm Bell Ringback disabled
OFF
I_______I
3
SIA Sends Programmed Rep. Codes
SIA Sends Automatic Rep. Codes
OFF
I_______I
4
Closing Confirmation Enabled
Closing Confirmation Disabled
ON
I_______I
5
Talk/Listen (PC5936) on phone lines 1/3
No Talk/Listen (PC5936) on phone lines 1/3
OFF
I_______I
6
Talk/Listen (PC5936) on phone line 2
No Talk/Listen (PC5936) on phone line 2
ON
OFF
I_______I
7
8
Contact ID Uses Programmed Rep. Codes
Local Mode Enabled
Contact ID Uses Automatic Rep. Codes
Local Mode Disabled
I_______I
[382] Third Communicator Option Code
Default
Option ON
OFF I_______I
1
Contact ID. Partial Closing Identifier is 5
OFF
Partial Closing ID is 4
OFF
I_______I
2
Alarm Communications Enabled During Walk Test* Alarm Communications Disabled During Walk Test
ON
I_______I
3
Communication Cancelled Message Enabled
Communication Cancelled Message Disabled
OFF
I_______I
4
Call Waiting Cancel Enabled**
Call Waiting Cancel Disabled
OFF
I_______I
5
T-Link Interface Enabled***
T-Link Interface Disabled
OFF
I_______I
6
AC Failure Transmission Delay is in Hours†
AC Failure Transmission Delay is in Minutes
OFF
I_______I
7-8
For Future Use
*This option must remain OFF for SIA-FAR installations.
** A Call Waiting Cancel on a non-Call Waiting line will prevent successful connection to the central station.
***T-Link Interface not investigated by UL.
† For central and remote fire applications, this option must be ON.
LINKS1000 Preambles
NOTE: Do not use this section for central and remote fire applications.
[390] LINKS1000 Preamble (First Telephone Number)
(Program all unused digits with Hex F)
Default: FFFF
I_______I_______I_______I_______I
[391] LINKS1000 Preamble (Second Telephone Number)
Default: FFFF
(Program all unused digits with Hex F)
I_______I_______I_______I_______I
[392] LINKS1000 Preamble (Third Telephone Number)
(Program all unused digits with Hex F)
Default: FFFF
I_______I_______I_______I_______I
[393] LINKS1000 Special Function Preamble (All Telephone Numbers)
Default: FFFFFF I_______I_______I_______I_______I_______I_______I (Program all unused digits with Hex F)
• Enter [*][2][*] (HEX B) to dial [*]
• Enter [*][3][*] (HEX C) to dial [#]
16
Downloading Options
Section 7: Downloading Options
[401] First Downloading Option Code
Default
Option
ON
OFF
OFF
I_______I
1
Answering machine/double call enabled Answering machine/double call disabled
ON
I_______I
2
User Can Enable DLS Window
User Cannot Enable DLS Window
OFF
I_______I
3
Call-Back Enabled
Call-Back Disabled
OFF
I_______I
4
User-initiated call-up enabled
User-initiated call-up disabled
OFF
I_______I
5
Auto Event Buffer Upload Enabled
Auto Event Buffer Upload Disabled
OFF
I_______I
6-8
For Future Use
[402] Downloading Computer’s Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[403] Downloading Access Code
Default: 5020 I_______I_______I_______I_______IEnter 4 HEX digits
[404] Panel Identification Code
Default: 5020 I_______I_______I_______I_______IEnter 4 HEX digits
[405] Answering Machine Double-call Timer
Default: 060 I_______I_______I_______I (Valid entries are 001-255 seconds)
[406] Number of Rings to Answer On
Default: 000 I_______I_______I_______I (Valid entries are 000-255 rings)
[490] LINKS Preamble (Downloading Telephone Number)
Default: FFFFI_______I_______I_______I_______I (Program all unused digits with Hex F)
[499] Initiate PC-Link (Local Downloading)
To begin PC-Link downloading, enter [499][Installer’s Code][499].
17
Section 8: Programmable Output
Programming
Programmable Output Attributes
Program only the following attributes for the PGM options listed. All others will be ignored. PGM options are programmed in [009],
[010] & [011].
PGM Attribute Defaults (Y = Attribute ON; N = Attribute OFF):
Attribute:
ON
OFF
1
2
3
4
5
6
7
8
Not used
Not used
True Output
Follows Timer
Code Req.
Not used
Not used
Not used
—
—
Inverted
On / Off
No Code Req.
—
—
—
PGM Option
[01] Burg. / Fire Bell
Y
[02] Future Use
[03] Sensor Reset
Y
[04] 2-Wire Smoke Support (PGM2 only)
Y
[05] Armed Status
Y
[06] Ready To Arm
Y
[07] Kypd Bzz Follow
Y
[08] Courtesy Pulse
Y
N
[09] System Trouble Output / Trouble Options)
Y
Y
Y
Y
Y
Y
Y
Y
[10] System Event / Event Options)
Y
Y
Y
Y
Y
Y
Y
Y
[11] System Tamper
Y
[12] TLM and Alarm
Y
[13] Kiss-off
Y
[14] Gnd Strt Pulse
Y
[15] Remote Op.
Y
[16] LINKS1000 Sup.
Y
[17] Away Armed Status
Y
[18] Stay Armed Status
Y
[19] Comm. Output #1, [*][7][1]
Y
Y
Y
[20] Comm. Output #2, [*][7][2]
Y
Y
N
[21] Comm. Output #3, [*][7][3]
Y
Y
N
[22] Comm. Output #4, [*][7][4]
Y
Y
N
[23] Silent 24 Hr (PGM2 only)
Y
[24] Audible 24 Hr (PGM2 only)
Y
[25] Delayed Burglary & Fire Bell
Y
1
Attribute:
2
3
4
5
6
7
8
PGM Option
ON
Serv. req.
AC Fail
TLM Fault
FTC
Zone Fault
Zone Tmp.
Zn. Low Bat.
Loss of Clock
OFF
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Y
Y
Y
Y
Y
Y
Y
Y
ON
Burg. Evnt.
Fire Evnt.
Panic Evnt.
Med. Evnt.
Supv. Evnt.
Priority Evnt.
Holdup Evnt.
Follows Timer*
OFF
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Latched
Y
Y
Y
Y
Y
Y
Y
N
[09] System Trouble
[10] System Event
*If attribute [8] is turned ON, attributes [1-7] must also be turned ON.
18
Programmable Output Programming:
Section PGM
#
Main Board
[501]
1
Output
Type*
(
[502]
(
2
1
2
3
4
)
I________I
I________|
I________|
I________|
)
I________I
I________|
I________|
I________|
5
6
7
8
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________I
PC5208
[503]
3
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[504]
4
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
6
7
8
*Record here based on programming in [009], [010] and [011].
Section PGM
#
PC5208
[505]
5
Output
Type*
1
2
3
(
[506]
6
[507]
7
[508]
8
4
5
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[509]
9
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[510]
10
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[511]
11
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[512]
12
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[513]
13
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[514]
14
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
PC5204
*Record here based on programming in [009], [010] and [011].
PGM Output Assignment
Section PGM
#
Main Board
[551]
1
I________I
[552]
2
I________I
[553]
3
I________I
[554]
4
I________I
[555]
5
I________I
[556]
6
I________I
[557]
7
I________I
[558]
8
I________I
[559]
9
I________I
[560]
10
I________I
[561]
11
I________I
[562]
12
I________I
[563]
13
I________I
[564]
14
I________I
PC5208
PC5204
19
Section 9: Inter n ational Programming
[700] Clock Adjust
Default: 60
I_______I______I
Valid entries are 01-99 seconds
[701] First International Options Code
Default
Option
ON
OFF I_______I
1
50 Hz AC
OFF
I_______I
2
Time Base - Internal Crystal
Time Base - AC Line
OFF
I_______I
3
AC/DC Arming Inhibit Enabled
AC/DC Arming inhibit disabled
OFF
I_______I
4
All System Tampers Require Installer Reset All System Tampers follow Restore
OFF
I_______I
5
6 digit User Access Codes
4 digit User Access Codes
OFF
I_______I
6
Busy Tone detection enabled
Busy Tone detection disabled
OFF
I_______I
7
High Current Battery Charge
Standard current battery charge
OFF
I_______I
8
For Future Use
[702] Second International Options Code
Default
Option ON
OFF I_______I
1
Pulse Dialing Make/Break Ratio is 33/67
OFF
Pulse Dialing Make/Break Ratio is 40/60
ON
I_______I
2
Force Dialing Enabled
OFF
I_______I
3
Land Line Test Transmission in Minutes
Land line Test Transmission in Days
OFF
I_______I
4
1600 Hz Handshake
Standard Handshake
OFF
I_______I
5
ID Tone Enabled
ID Tone Disabled
OFF
I_______I
6
2100 Hz ID Tone
1300 Hz ID Tone
OFF
OFF
I_______I
7
8
One Time 1-Hr User Enabled DLS Window Full 6-Hr User Enabled DLS Window
Bell on FTC when Armed
FTC Trouble only when Armed
I_______I
[703] Delay Between Dialing Attempts
Default:003 I_______I_______I_______I
Valid entries are 000-255 Seconds
20
OFF
60 Hz AC
Force Dialing Disabled
Section 10: Module Programming
[801] PC5400 Printer Module Programming
Please refer to your PC5400 Installation Manual for installation and programming instructions.
[802] PC5936 Audio Interface Programming
Please refer to your PC5936 Installation Manual for installation and programming instructions.
[803] Alternate Communicator Programming
Please refer to your LINKS1000, LINKS2X50, Skyroute, PC5400 ADT DVACS or PC5400 Sur-Gard DVACS Installation Manual for
installation and programming instructions.
[804] PC5132 Wireless Expansion Programming
Please refer to your PC5132 Installation Manual for programming locations and instructions.
[851] T-Link Programming
Please refer to your T-Link Installation Manual for programming locations and instructions.
NOTE: T-Link feature not investigated by UL.
NOTE: To enable T-Link, Option [5] in Section [382] must be ON and the receiver telephone number must be programmed with
DCAA in sections [301]-[303].
Section 11: Special Installer Functions
[901] Installer Walk Test Mode Enable / Disable
[902] Module Supervision Reset
[903] Module Supervision Field
[904] Wireless Module Placement Test
For more information, please refer to your PC5132 Installation Manual
• Select the module / transmitter (Zones 01-32).
• Press [#] to Cancel.
Placement
Good
Led Keypad
Light 1 ON Steady
LCD Keypad
“GOOD”
Bell / Buzzer
1 Beep / Squawk
Fair
Light 2 ON Steady
“FAIR”
2 Beeps / Squawks
Bad
Light 3 ON Steady
“BAD”
3 Beeps / Squawks
[990] Installer Lockout Enable
[991] Installer Lockout Disable
[993] Restore Alternate Communicator (LINKS2X50, Skyroute, PC5400) to Factory Default Programming
[995] Restore Escort5580 to Factory Default Programming
[996] Restore PC5132 to Factory Default Programming
[997] Restore PC5400 to Factory Default Programming
[998] Restore PC5936 to Factory Default Programming
[999] Restore PC5019 to Factory Default Programming
21
Appendix A: Programming LCD5500Z/
LCD5520Z Keypads
If you have an LCD5500Z/LCD5520Z keypad, additional programming is required for proper operation. All LCD programming is
done per keypad. If more than one LCD keypad are present on the system, labels programmed at one keypad can be broadcast
to all other LCD keypads. Check the software version of the keypad you are programming, and refer to the correct programming
instructions.
LCD5500Zv2.x and Lower Keypads
The following is a description of the available programming
options and their accompanying programming sections:
How to Enter LCD Programming
Programming LCD keypads is similar to programming the rest of
the system. Follow the programming procedure as outlined in
Section 3 of the Installation Manual.
1. Enter keypad programming by pressing [*][8][Installer’s Code].
2. Press the [*] key.
3. Enter the two-digit section number to be programmed.
Programmable Labels
Zone labels and other LCD display identifiers can be customized
to make operation of the system easier for the end user. The following procedure should be used for creating all LCD labels:
1. Enter Installer Programming. Enter the two-digit section number for the label to be programmed.
[01] to [32] Zone Labels (14 Characters)
Default: “Zone 1” - “Zone 32”
3. Use the arrow keys (<>) to move the underline bar underneath the letter to be changed.
4. Press the number key [1] to [9] corresponding to the letter
you require. The first time you press the number the first letter will appear. Pressing the number key again will display the
next letter. Refer to the following chart:
[1] - A, B, C, 1
[6] - P, Q, R, 6
[2] - D, E, F, 2
[7] - S, T, U, 7
[3] - G, H, I, 3
[8] - V, W, X, 8
[4] - J, K, L, 4
[9] - Y, Z, 9,0
[5] - M, N, O, 5
[0] - Space
5. When the required letter or number is displayed use the
arrow keys (<>) to scroll to the next letter.
6. When you are finished programming the Zone Label, press
the [*] key, scroll to “Save,” then press [*].
7. Continue from Step 2 until all Labels are programmed.
[33] Fire Alarm Label (14 Characters)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Fire Zone”
[34] and [35] Partition Labels (14 Characters)
Default: “System”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Partition 2”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[40] Partition 1 and [41] Partition 2 “Command Output 1” Label (14 Characters)
Default: “Command_O/P_1”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Command_O/P_1”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[44] Partition 1 and [45] Partition 2 “Command Output 2” Label (14 Characters)
Default: “Command_O/P_2”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Command_O/P_2”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[46] Partition 1 and [47] Partition 2 “Command Output 3” Label (14 Characters)
Default: “Command_O/P_3”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Command_O/P_3”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[48] Partition 1 and [49] Partition 2 “Command Output 4” Label (14 Characters)
Default: “Command_O/P_4”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Command_O/P_4”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[51] Fail to Arm Event Message
Default: “System Has Failed to Arm”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[52] Alarm When Armed Event Message
Default: “Alarm Occurred While Armed < >” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
22
Special Installer Functions:
[60]
First User Display Mask
Default
Option ON
ON
I_______I
1
Hold [P]anic Keys prompt ON
OFF
Hold [P]anic Keys prompt OFF
ON
I_______I
2
Zone Bypassing prompt ON
Zone Bypass prompt OFF
ON
I_______I
3
Troubles prompt ON
Troubles prompt OFF
ON
I_______I
4
Alarm Memory prompt ON
Alarm Memory prompt OFF
ON
I_______I
5
Door Chime Control prompt ON
Door Chime Control prompt OFF
ON
I_______I
6
Access Codes prompt ON
Access Codes prompt OFF
ON
I_______I
7
User Functions prompt ON
User Functions prompt OFF
ON
I_______I
8
Output Control prompt ON
Output Control prompt OFF
[61]
Second User Display Mask
Default
Option ON
OFF
I_______I
1
Installer Programming prompt ON
OFF
Installer Programming prompt OFF
ON
I_______I
2
Stay Arm prompt ON
Stay Arm prompt OFF
ON
I_______I
3
Quick Arm prompt ON
Quick Arm prompt OFF
ON
I_______I
4
Interior Arm prompt ON
Interior Arm prompt OFF
OFF
I_______I
5
Quick Exit prompt ON
Quick Exit prompt OFF
View Event Buffer prompt OFF
ON
I_______I
6
View Event Buffer prompt ON
OFF
I_______I
7
For Future Use
OFF
I_______I
8
Music Input ON
[62]
Third User Display Mask
Default
Option ON
ON
I_______I
1
System Test prompt ON
Music Input OFF
OFF
System Test prompt OFF
ON
I_______I
2
Time and Date prompt ON
Time and Date prompt OFF
ON
I_______I
3
Auto-arm Control prompt ON
Auto-arm Days prompt OFF
ON
I_______I
4
Auto-arm Time prompt ON
Auto-arm Time prompt OFF
ON
I_______I
5
Download Enable prompt ON
Download Enable prompt OFF
ON
I_______I
6
Bright Control prompt ON
Bright Control prompt OFF
ON
I_______I
7
Contrast Control prompt ON
Contrast Control prompt OFF
ON
I_______I
8
Buzzer Control prompt ON
Buzzer Control prompt OFF
[63]
Downloaded LCD Message Duration
Default: 003 I_______I_______I_______I (Valid entries are 000-255, 000=Unlimited Message Display. This number represents the number of
times the Downloaded message is cleared by pressing any key while the message is up after timeout)
[64]
Key Options
Default
Option
ON
I_______I
1
ON
[F]ire Keys enabled
OFF
[F]ire Keys disabled
ON
I_______I
2
[A]uxiliary Keys enabled
[A]uxiliary Keys disabled
ON
I_______I
3
[P]anic Keys enabled
[P]anic Keys disabled
OFF
I_______I
4-8
For Future Use
[65]
Fourth User Display Mask
Default
Option ON
ON
I_______I
1
User Initiated Call-up prompt ON
OFF
User Initiated Call-up prompt OFF
OFF
I_______I
2
For Future Use
OFF
I_______I
3
For Future Use
ON
I_______I
4
Command Output #1 prompt ON
Command Output #1 prompt OFF
ON
I_______I
5
Command Output #2 prompt ON
Command Output #2 prompt OFF
OFF
I_______I
6
Command Output #3 prompt ON
Command Output #3 prompt OFF
OFF
I_______I
7
Command Output #4 prompt ON
Command Output #4 prompt OFF
OFF
I_______I
8
For Future Use
23
[66]
Keypad Options
Default
Option
ON
I_______I
1
ON
Display Access Code when Programming
OFF
Display ‘X’ when Programming
ON
I_______I
2
Local Clock Display Enabled
Local Clock Display Disabled
OFF
I_______I
3
Local Clock Displays 24 Hour time
Local Clock Displays AM/PM
ON
I_______I
4
Auto Alarm Memory Scroll Enabled
Auto Alarm Memory Scroll Disabled
OFF
I_______I
5
Local Display of Temperature Enabled*
Local Display of Temperature Disabled
OFF
I_______I
6
Bypass Options prompt ON
Bypass Options prompt OFF
OFF
I_______I
7-8
For Future Use
[67] Fifth User Display Mask
Default
Option ON
OFF
I_______I
1
Thermostat CTRL Prompt ON*
OFF
Thermostat CTRL Prompt OFF
OFF
I_______I
2
Temperature Setting Prompt ON*
OFF
I_______I
3
Occupancy Mode Prompt ON*
Occupancy Mode Prompt OFF
OFF
I_______I
4
Thermostat Mode Prompt ON*
Thermostat Mode Prompt OFF
OFF
I_______I
5
Fan Control Prompt ON*
Fan Control Prompt OFF
OFF
I_______I
6
For Keypad View Prompt ON*
For Keypad View Prompt OFF
OFF
I_______I
7-8
Temperature Setting Prompt OFF
For Future Use
[68] Sixth User Display Mask
Default
Option ON
OFF
I_______I
1
Occupancy Mode Auxiliary Prompt ON*
OFF
Occupancy Mode Auxiliary Prompt OFF
OFF
I_______I
2
Occupancy Mode Day Prompt ON*
Occupancy Mode Day Prompt OFF
OFF
I_______I
3
Occupancy Mode Away Prompt ON*
Occupancy Mode Away Prompt OFF
OFF
I_______I
4
Occupancy Mode Night Prompt ON*
Occupancy Mode Night Prompt OFF
OFF
I_______I
5-8
For Future Use
NOTE: These options are only relevant if you are using an LCD5500Z v2.1 or higher or an LCD5520Z v3.1.
[97] View Software Version
[98] Initiate Global Label Broadcast
All LCD programming is done per keypad. If more than one LCD keypad are present on the system, and the PC5400 receives
labels, labels programmed at one keypad can be broadcast to all other LCD keypads. Perform the following procedure in order to
broadcast labels:
Step 1 - Program one LCD keypad completely.
Step 2 - Make sure all LCD keypads are connected to the Keybus.
Step 3 - Enter Installer’s Programming, then enter section [98] at the keypad that was programmed. The keypad will now broadcast
all the information programmed to all the other LCD keypads on the system.
Step 4 - When the keypad is finished press the [#] key to exit.
[99] Reset LCD EEPROM to Factory Defaults
ASCII Characters
24
Special Installer Functions:
LCD5500Z/LCD5520Z v3.x and Higher Keypads
The following is a description of the available programming
options and their accompanying programming sections:
How to Enter LCD Programming
Programming LCD keypads is similar to programming the rest of
the system. Follow the programming procedure as outlined in
Section 3 of the Installation Manual.
1. Enter keypad programming by pressing [*][8][Installer Code].
2. Press the [*] key.
3. Enter the three-digit section number to be programmed (see
the following page for section numbers).
Programmable Labels
Zone labels and other LCD display identifiers can be customized to
make operation of the system easier for the end user. The following
procedure should be used for creating all LCD labels:
1. Enter Installer’s Programming. Enter the three-digit section number for the label to be programmed.
2. Use the arrow keys (<>) to move the underline bar underneath
the letter to be changed.
3. Press the number key [1] to [9] corresponding to the letter you
require. The first time you press the number the first letter will
appear. Pressing the number key again will display the next letter.
Refer to the following chart:
[1] - A, B, C, 1
[6] - P, Q, R, 6
[2] - D, E, F, 2
[7] - S, T, U, 7
[3] - G, H, I, 3
[8] - V, W, X, 8
[4] - J, K, L, 4
[9] - Y, Z, 9,0
[5] - M, N, O, 5
[0] - Space
4. When the required letter or number is displayed use the arrow
keys (<>) to scroll to the next letter.
5. When you are finished programming the Zone Label, press the [*]
key, scroll to “Save,” then press [*].
6. Continue from Step 2 until all Labels are programmed.
[001] to [032] Zone Labels (14 Characters)
Default: “Zone 1” - “Zone 32”
[065] Fire Alarm Label (14 Characters)
Default: “Fire Zone”I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[066] Fail to Arm Event Message
Default: “System Has Failed to Arm” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[067] Alarm When Armed Event Message
Default: “Alarm Occurred While Armed < >”I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[070] First User Display Mask
Default
Option ON
OFF
ON I_______I
1
Hold [P]anic Keys prompt ON
Hold [P]anic Keys prompt OFF
ON I_______I
2
Zone Bypassing prompt ON
Zone Bypass prompt OFF
ON I_______I
3
Troubles prompt ON
Troubles prompt OFF
ON I_______I
4
Alarm Memory prompt ON
Alarm Memory prompt OFF
ON I_______I
5
Door Chime Control prompt ON
Door Chime Control prompt OFF
ON I_______I
6
Access Codes prompt ON
Access Codes prompt OFF
ON I_______I
7
User Functions prompt ON
User Functions prompt OFF
ON I_______I
8
Output Control prompt ON
Output Control prompt OFF
[071] Second User Display Mask
Default
Option ON
OFF
1
Installer Programming prompt ON
Installer Programming prompt OFF
OFF I_______I
ON I_______I
2
Stay Arm prompt ON
Stay Arm prompt OFF
3
Quick Arm prompt ON
Quick Arm prompt OFF
ON I_______I
4
Interior Arm prompt ON
Interior Arm prompt OFF
ON I_______I
OFF I_______I
5
Quick Exit prompt ON
Quick Exit prompt OFF
6
View Event Buffer prompt ON
View Event Buffer prompt OFF
ON I_______I
7
For Future Use
OFF I_______I
OFF I_______I
8
Music Input ON
Music Input OFF
[072] Third User Display Mask
Default
Option ON
OFF
ON
I_______I
1
System Test prompt ON
System Test prompt OFF
I_______I
2
Time and Date prompt ON
Time and Date prompt OFF
ON
ON
I_________I
3
Auto-arm Control prompt ON
Auto-arm Days prompt OFF
ON
I_________I
4
Auto-arm Time prompt ON
Auto-arm Time prompt OFF
I_________I
5
Download Enable prompt ON
Download Enable prompt OFF
ON
ON
I_________I
6
Bright Control prompt ON
Bright Control prompt OFF
ON
I_________I
7
Contrast Control prompt ON
Contrast Control prompt OFF
I_________I
8
Buzzer Control prompt ON
Buzzer Control prompt OFF
ON
25
[073] Downloaded LCD Message Duration
Default: 003 I_______I_______I_______I (Valid entries are 000-255, 000=Unlimited Message Display. This number represents the number of
times the Downloaded message is cleared by pressing any key while the message is up after timeout)
[074] Key Options
Default
Option ON
OFF
ON
I_______I
1
[F]ire Keys enabled
[F]ire Keys disabled
I_______I
2
[A]uxiliary Keys enabled
[A]uxiliary Keys disabled
ON
ON
I_______I
3
[P]anic Keys enabled
[P]anic Keys disabled
I________I
4-8
For Future Use
OFF
[075] Fourth User Display Mask
Default
Option ON
OFF
ON
I_______I
1
User Initiated Call-up prompt ON
User Initiated Call-up prompt OFF
OFF
I_______I
2
Last Code to Disarm/Arm prompt ON
Last Code to Disarm/Arm prompt OFF
OFF
I_______I
3
Walk Test Prompt ON
Walk Test Prompt ON
ON
I_______I
4
Command Output #1 prompt ON
Command Output #1 prompt OFF
ON
I_______I
5
Command Output #2 prompt ON
Command Output #2 prompt OFF
OFF
I_______I
6
Command Output #3 prompt ON
Command Output #3 prompt OFF
OFF
I_______I
7
Command Output #4 prompt ON
Command Output #4 prompt OFF
OFF
I_______I
8
For Future Use
[076] Keypad Options
Default
Option
ON
I_______I
1
ON
Display Access Code when Programming
OFF
Display ‘X’ when Programming
ON
I_______I
2
Local Clock Display Enabled
Local Clock Display Disabled
OFF
I_______I
3
Local Clock Displays 24 Hour time
Local Clock Displays AM/PM
ON
I_______I
4
Auto Alarm Memory Scroll Enabled
Auto Alarm Memory Scroll Disabled
OFF
I_______I
5
Local Display of Temperature Enabled*
Local Display of Temperature Disabled
OFF
I_______I
6
Bypass Options prompt ON
Bypass Options prompt OFF
OFF
I_______I
7
For Future Use
OFF
I_______I
8
Auto Scroll Open Zones Enabled
[077] Fifth User Display Mask
Default
Option ON
OFF
I_______I
1
Thermostat CTRL Prompt ON*
Auto Scroll Open Zones Disabled
OFF
Thermostat CTRL Prompt OFF
OFF
I_______I
2
Temperature Setting Prompt ON*
Temperature Setting Prompt OFF
OFF
I_______I
3
Occupancy Mode Prompt ON*
Occupancy Mode Prompt OFF
OFF
I_______I
4
Thermostat Mode Prompt ON*
Thermostat Mode Prompt OFF
OFF
I_______I
5
Fan Control Prompt ON*
Fan Control Prompt OFF
OFF
I_______I
6
For Keypad View Prompt ON*
For Keypad View Prompt OFF
OFF
I_______I
7-8
For Future Use
[078] Sixth User Display Mask
Default
Option ON
OFF
I_______I
1
Occupancy Mode Auxiliary Prompt ON*
OFF
Occupancy Mode Auxiliary Prompt OFF
OFF
I_______I
2
Occupancy Mode Day Prompt ON*
Occupancy Mode Day Prompt OFF
OFF
I_______I
3
Occupancy Mode Away Prompt ON*
Occupancy Mode Away Prompt OFF
OFF
I_______I
4
Occupancy Mode Night Prompt ON*
Occupancy Mode Night Prompt OFF
OFF
I_______I
5-8
For Future Use
NOTE: These options are only relevant if you are using LCD5500Z v2.1 or higher or LCD5520Z v3.1 and higher keypads.
Partition Labels
Default: “System” - “Partition 2”
Section
Partition
Label
[101]
1/System
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[102]
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
26
Special Installer Functions:
Command Output Labels
Default: “Command_O/P_1” - “Command_O/P_4”
Program a label for each Command Output used, as it will appear at each partition ( of the Installation Manual).
Section
Partition
Command Output
Label
[120]
1
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[121]
1
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[122]
1
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[123]
1
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[124]
2
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[125]
2
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[126]
2
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[127]
2
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[[997]View Software Version
[998] Initiate Global Label Broadcast
All LCD programming is done per keypad. If more than one LCD keypad are present on the system, and the PC5400 receives
labels, labels programmed at one keypad can be broadcast to all other LCD keypads. Perform the following procedure in order to
broadcast labels:
Step 1 - Program one LCD keypad completely.
Step 2 - Make sure all LCD keypads are connected to the Keybus.
Step 3 - Enter Installer’s Programming, then enter section [998] at the keypad that was programmed. The keypad will now broadcast all the information programmed to all the other LCD keypads on the system.
Step 4 - When the keypad is finished press the [#] key to exit.
[999]
Reset LCD EEPROM to Factory Defaults
ASCII Characters
27
Appendix B: Programming LCD5501Z Keypads
There are several programming options available for the LCD5501Z keypad. These are described below. Record all your programming choices in the programming worksheets included in this manual.
Programming Keypad Options
Programming the LCD5501Z is similar to programming the rest
of the system. To change the keypad programming:
1.
2.
3.
4.
Enter [*][8][Installer’s code]
Enter [000] to go to keypad programming
Enter section number [6] or [7].
To turn any of the options on or off, press the option number
(from [1] to [8]).
5. When you are finished programming, press [#].
When you are in the LCD5501Z programming sections, the keypad will display which options are turned on along the top of the
display. To turn an option on or off, press the number corresponding to the option on the number pad. The numbers of the
options that are currently turned ON will be displayed.
For example, if options 1 and 2 are on, the display will look like:
Clock Options
The LCD5501Z will display the current time after 30 seconds of
no key presses. To set the correct time and date for the system,
please refer to the PowerSeries User Guide. You can change how
the keypad displays the time with options [1] to [3] in programming section [6].
NOTE: If the Time does not display on keypad option is selected, make sure that the Keypad displays time when zones are open
option is also selected.
Alarms Displayed While Armed Option
You can disable the display of alarms on the keypad when the
system is armed. The display of alarms is enabled by default. To
disable the display of alarms when the system is armed, turn off
section [6], option [5].
off on the keypad, enter section [7], and turn on or off options
[1] to [3].
Emergency Key Options
You can enable or disable the Fire, Auxiliary and Panic keys at
each keypad. These keys are enabled by default. Please see the
PC1555 CP-01 Installation Manual for more information on these
keys and their options. To turn any of the emergency keys on or
To change the door chime opening/closing settings, at each
LCD5501Z keypad, enter section [6], and turn on or off options
[6] and [7].
Door Chime on Zone Openings/Closings
By default, LCD5501Z keypads are programmed to sound door
chimes on both zone openings and closings.
[6] LCD5501Z Keypad Options
Default
Option On
Off
ON
I________I
1
Local Clock Display Enabled
ON
I________I
2
Local Clock Displays AM/PM
Local Clock Display Disabled
Local Clock Displays 24-hour Time
OFF
I________I
3
Open Zones Override Clock Display
Open Zones Do Not Override Clock
OFF
I________I
4
Scandinavian Approvals enabled
Scandinavian Approvals disabled
OFF
I________I
5
Alarms Not Displayed While Armed
Alarms Always Displayed While Armed
ON
I________I
6
Door Chime Enabled for Zone Openings
Door Chime Disabled for Zone Openings
ON
I________I
7
Door Chime Enabled for Zone Closings
Door Chime Disabled for Zone Closings
OFF
I________I
8
For Future Use
[7] Emergency Key Options
Default
Option On
Off
ON
I________I
1
[F]ire Keys Enabled
ON
I________I
2
[A]uxiliary Keys Enabled
[A]uxiliary Keys Disabled
ON
I________I
3
[Panic] Keys Enabled
[P]anic Keys Disabled
OFF
I________I
4-8
[F]ire Keys Disabled
For Future Use
Programming Door Chime Options
You can program the LCD5501Z keypad to sound a tone when
any zone is opened or closed. There are two parts to the
LCD5501Z door chime programming:
• Program if the LCD5501Z will chime when zones are opened
and/or closed (see ).
• Program the type of sound the LCD5501Z will make when an
individual zone is opened or closed.
For the door chime feature to work, you will also need to turn on
the Door Chime attribute for each zone that will trigger the
chime. This programming is done in the control panel software.
Refer to the PC1555 CP-01 Installation Manual for more informa-
tion.
28
Special Installer Functions:
Door Chime Sounds
You can program the LCD5501Z keypad to make different door
chime sounds for individual zones, or groups of zones. Each
LCD5501Z keypad can make any of four door chime sounds for
each zone that triggers the door chime:
• ·6 quick beeps (default sound)
• ·‘Bing – Bing’ tone
• ·‘Ding – Dong’ tone
• ·‘Alarm’ tone
NOTE: For a zone to be able to trigger the door chime sound,
the Door Chime zone attribute must also be enabled in the
control panel programming. Please see your PC1555 CP-01
Installation Manual.
To change the door chime sounds:
4. Turn one of the following options on by pressing [1], [2], [3],
or [4]:
[1] 6 quick beeps (default sound)
[2]‘Bing – Bing’ tone
[3]‘Ding – Dong’ tone
[4]‘Alarm’ tone
NOTE: Make sure that only one of the above options is turned
on. If more than one is on, the keypad will sound the first option
that is enabled. If none of the options are selected, the keypad
will not make any sound when the zone is opened or closed.
5. To program the door chime sound for another zone, repeat
steps 3 and 4.
6. When you are finished programming the door chime sounds,
press [#] to exit.
1. Enter [*][8][Installer’s code].
2. Enter [*] to go to door chime sound programming.
Door Chime Sound Programming
Zone
Location
3. Enter the 2-digit number for the zone you are programming
[01] - [32].
NOTE: LCD5501Z v 1.x keypads only support zones 1 to 32.
Options:
[1]
[2]
6 Beeps
(default)
“Bing-bing”
[3]
[4]
“Ding-dong” Alarm tone
[01]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[02]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[03]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[04]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[05]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[06]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[07]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[08]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[09]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[10]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[11]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[12]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[13]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[14]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[15]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[16]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[17]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[18]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[19]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[20]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[21]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[22]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[23]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[24]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[25]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[26]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[27]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[28]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[29]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[30]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[31]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[32]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
29
Notes
Industry Canada Statement
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the
equipment meets certain telecommunications network protective, operational and safety requirements.
Industry Canada does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to disconnect
the equipment.
User should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal equipment provides
an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.
AVIS : L’étiquette de l’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le
matériel est conforme à certaines normes de protection, d’exploitation et de sécurité des réseaux de télécommunications. Industrie Canada n’assure toutefois pas que le matériel fonctionnera à la satisfaction de
l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations
de l’entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement. L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêchent pas la dégradation du service dans certaines situations.
Les réparations de matériel homologué doivent être effectuées par un centre d’entretien canadien autorisé
désigné par le fournisseur. La compagnie de télécommunications peut demander à l’utilisateur de
débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause
de mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source
d’énergie électrique, les lignes téléphoniques et les canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.
AVERTISSEMENT : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir
recours à un service d’inspection des installations électriques, ou à un électricien, selon le cas.
AVIS : L'indice d'équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre
maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d'une
interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme
d'indices d'équivalence de la sonnerie de tous les dispositifs n'excède pas 5.
L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls
Ltd. could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interfer-ence in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How to Identify and
Resolve Radio/Television Interference Problems". This booklet is available from the U.S.
Government Printing Office, Wash-ington D.C. 20402, Stock # 004-000-00345-4.
Incidence of Harm
IMPORTANT INFORMATION
Additional Information
This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a
label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this number must be provided to the
Telephone Company.
FCC Registration Number:
F53CAN-34330-AL-E
REN:
0.1B
USOC Jack:
RJ-31X
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing
equipment must be connected to a properly installed RJ-31X jack that is electrically in series
with and ahead of all other equipment attached to the same telephone line. Proper installation
is depicted in the figure below. If you have any questions concerning these instructions, you
should consult your telephone company or a qualified installer about installing the RJ-31X
jack and alarm dialing equipment for you.
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the
ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation
instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as determined by the total
RENs, contact the local Telephone Company. For products approved after July 23, 2001, the
REN for this product is part of the product identifier that has the format.
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point
(e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
If this equipment PC1555 CP-01 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required.
But if advance notice is not practical, the Telephone Company will notify the customer as
soon as possible. Also, you will be advised of your right to file a complaint with the FCC if
you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the Telephone Company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment PC1555 CP-01, for repair or warranty information, please contact the facility indicated below. If the equipment is causing harm to the
telephone network, the Telephone Company may request that you disconnect the equipment
until the problem is solved. This equipment is of a type that is not intended to be repaired by
the end user. Simplex Time Recorder Co. 100 Simplex Drive, Westminster MA 01441-0001
USA, Tel: (978) 731-2500.
Customer Premises Equipment and Wiring
Network
Service
Provider's
Facilities
Computer
RJ-31X
Jack
Alarm Dialing
Equipment
Unused
RJ-11 Jack
Telephone
Line
Telephone
Network
Demarcation
Point
Fax Machine
Telephone
Answering
System
Telephone
Unused
RJ-11 Jack
©2003 Digital Security Controls Ltd.
Toronto • Canada • 1-800-387-3630 • www.dsc.com
Printed in Canada
2 9 0 3 4 6 7 7 R0 0 2