Crystal fires | Jewel | Technical data | crystal fires Jewel Technical data

CRYSTAL FIRES
1 BECHERS DRIVE
AINTREE RACECOURSE
BUSINESS PARK
AINTREE
LIVERPOOL
L9 5AY
CRYSTAL GEM
DECORATIVE FUEL EFFECT GAS FIRE
THIS APPLIANCE IS CATEGORY I2H FOR USE
WITH NATURAL GAS AT A SUPPLY
PRESSURE OF 20 mbar OR CATEGORY I3P
FOR USE WITH PROPANE AT A SUPPLY
PRESSURE OF 37mbar
G.B. AND I.E.
INSTALLATION & SERVICING BOOK
ISSUE 1
1
265mm
230mm
400mm
460mm
585mm
GEM BOX SIZES NOT INCLUDING TRIMS
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE YOU START INSTALLING THE
APPLIANCE.
KEEP THIS BOOKLET HANDY FOR FUTURE REFERENCE
ISSUE 1
2
TECHNICAL DATA
GAS TYPE:
GAS PRESSURE:
CONNECTION
INJECTOR:
REMOTE CONTROL
HEAT INPUT
NATURAL GAS
20mbar
8mm TUBE
CAT 82/440
CAT 82/460
6.9kW HIGH
4.1kW LOW
PROPANE
37mbar
8mm TUBE
CAT 92/160
CAT 92/160
5.4kW HIGH
2.9kW LOW
DATA BADGE ON FRONT BOTTOM SECTION OF APPLIANCE
IMPORTANT NOTES
THIS APPLIANCE IS FITTED WITH AN ATMOSPHERE SENSING DEVICE AND CAN ONLY BE
FITTED IN CONJUNCTION WITH THE FOLLOWING FLUES.
CONVENTIONAL BRICK OR STONE CHIMNEY.
OR A METAL FLUE BOX CONFORMING TO BS715
A NON COMBUSTIBLE HEARTH MUST BE PROVIDED TO COMPLY WITH THE BUILDING
REGULATIONS OR A SUITABLE PROPRIETARY FIRE SURROUND WITH 100 DEGREES C
RATING.
THE CHIMNEY OR FLUE (UNLESS NEW) MUST BE SWEPT BEFORE INSTALLATION, IF IT
HAS BEEN USED FOR SOLID FUEL
INSTALLER
THIS APPLIANCE MUST BE INSTALLED BY A COMPETENT PERSON
IE. A REGISTERED INSTALLER IN ACCORDANCE WITH THE
CURRENT EDITION OF THE GAS SAFETY (INSTALLATION AND USE) REGULATIONS OR
THE RULES IN FORCE. FAILURE TO DO SO COULD LEAD TO PROSECUTION.
VENTILATION GREAT BRITAIN
NO SPECIAL VENTILATION BRICKS OR VENTS ARE NORMALLY REQUIRED INTO THE
ROOM CONTAINING THE APPLIANCE, PROVIDED NORMAL ADVANTAGEOUS ROOM
VENTILATION EXISTS, THE INSTALLER MUST SATISFY THIS POINT BY A MANDATORY
SPILLAGE TEST.
IRELAND. PURPOSE PROVIDED VENTILATION MUST BE PROVIDED AND MUST HAVE A
MINIMUM FREE AREA OF 100CM2
WARNING
THIS APPLIANCE HAS A NAKED FLAME, AS WITH ALL SUCH FIRES IT IS
RECOMMENDED THAT A FIREGUARD SHOULD BE USED FOR THE PROTECTION OF
CHILDREN, THE ELDERLY AND INFIRM. FIRE GUARDS SHOULD CONFORM TO BS8423
2002 (FIREGUARDS FOR FIRES AND HEATING APPLIANCES FOR DOMESTIC USESPECIFICATION)
ISSUE 1
3
INSTALLATION REQUIREMENTS
CONVENTIONAL CHIMNEY
A CONVENTIONAL BRICK OR STONE CHIMNEY AS USED FOR SOLID FUEL APPLIANCE
WITH A MINIMUM EFFECTIVE CROSS SECTIONAL
DIMENSION OF 225*225mm, WITH A MINIMUM OF 3 METERS EFFECTIVE HEIGHT.
A LINED FLUE WITH A MINIMUM DIAMETER OF 125mm WITH THE FIREPLACE
COMPONENTS CONFORMING TO BS 1251
A BUILDERS OPENING A MINIMUM OF 560mm HIGH AND 400mm WIDE WITH A MINIMUM
DEPTH OF 260mm TO ALLOW SUFFICIENT VOLUME OF DEBRIS COLLECTION.
TO OBTAIN THIS DEPTH IT IS NECESSARY TO REMOVE THE CHAIRBRICK.(EXCEPT WHEN
INSTALLING FIRETRAY ONLY)
ANY PERMANENT FLUE RESTRICTION OR VARIABLE DAMPER MUST BE REMOVED OR
LOCKED FULLY OPEN.
THE CHIMNEY MUST BE SWEPT PRIOR TO INSTALLATION IF NOT NEW.
THE CHAIRBRICK MUST BE REMOVED ON ALL INSTALLATIONS.
EXCEPT WHEN INSTALLING FIRETRAY ONLY
WHEN INSTALLING FIRETRAY THE FOLLOWING HEARTH AND HEIGHT DIMENSIONS
MUST BE ADHERED TOO
fig 2
ISSUE 1
4
INSTALLATION REQUIREMENTS FIRETRAY ONLY
THE GEM FIRETRAY MAY BE INSTALLED INTO A STANDARD FIREBACK OR HOT BOX
INSTALLED WITH A CERAMIC FIRE BACK
OR HOLE IN THE WALL FIREPLACE WHERE THE OPENING HEIGHT DOES NOT EXCEED
560mm (ie sunrise gas appliance)
THE INSTALLATION MUST ADHERE TO OPENING SIZES IN FIG 2
THE RELEVANT BRITISH STANDARDS MUST BE FOLLOWED
BS EN 1856
BS 5871 :PART 3
BS 5440: PART 1 AND 2
BS 6891
BS 8303
BS 1251
AND I.S 813 FOR IRELAND
FIRE TRAY SIZES NOT INCLUDING CERAMICS
TOP VIEW
O
O
ISSUE 1
POSITION FIRETRAY
210 mm TO LEVEL
WITH TRAY FRONT
LEG, MARK DRILL
AND PLUG HOLES
SCREW AND
SECURE
5
Front view
545mm high
395mm wide
Top view of flue opening
100mm
minimum
250 mm minimum
A CERAMIC FIREBACK TO BS1251 INSTALLED IN A METAL BOX ,CAN BE USED AS A
HOTBOX TO HOUSE THE GEM FIRETRAY
MUST BE TO THE DIMENSIONS SHOWN ABOVE
ISSUE 1
6
INSTALLATION REQUIREMENTS
5 “ FLUE PIPE AND STARTER BOX
A DOUBLE WALLED SELKIRK RECESSED FLUE BOX BUILT TO THE REQUIREMENTS OF BS 715 OR
BS EN 1856 WITH AN INSULATED FLUE HAVING A MINIMUM DIAMETER OF 125mm (5”) AND A
MINIMUM EFFECTIVE OVERALL HEIGHT OF 3 METRES (10ft)
RECESSED GAS FLUE BOX DIMENSIONS (NOT INCLUDING FIBREGLASS INSULATION)
NOTE
THE METAL FLUE BOX MUST BE INSULATED WITH FIBRE GLASS OR EQUIVALENT TO A THICKNESS OF 25 mm.
NOTE
WHERE INSTALLATION IS FOR A METAL FLUE BOX, THE SURROUND MUST HAVE A TEMPERATURE RATING OF 150 DEGREES C .
NOTE
IF THE FLUE BOX IS TO BE USED WITH AN EXISTING BRICK OR STONE CHIMNEY A 125 mm (5”) MINIMUM DIAMETER FLUE LINER
CONFORMING TO BS 715 MAY BE USED.
NOTE
A BRICK CHAMBER TO THE SIZES IN FIG 2 IN AN EXISTING BRICK OR STONE CHIMNEY A
125mm MINIMUM DIAMETER FLUE LINER CONFORMING TO BS EN 1856 MAY BE USED,
PROVIDING IT IS SEALED AT THE TOP AND BOTTOM OF THE EXISTING BRICK OR STONE
CHIMNEY.
NOTE
ANY OF THE ABOVE FLUES MUST NOT BE RESTRICTED BY DAMPERS OR REGISTER
PLATES, THE FLUE MUST SERVE ONLY ONE APPLIANCE AND NOT HAVE ANY BRANCHES
OR TRAPS WHICH MAY IMPEDE THE NATURAL DRAUGHT .IF ANY TERMINAL IS FITTED
IT MUST BE SUITABLE FOR THE PURPOSE.
ISSUE 1
7
FIG 3
THE FRONT FACE SEAL MUST BE FLAT TO ENSURE A GOOD SEAL IS FORMED BETWEEN
THE REAR AND BASE OF THE APPLIANCE AND CHIMNEY TO AVOID ANY REDUCTION IN
THE NATURAL DRAUGHT.
ALWAYS ENSURE THE HEARTH IS LEVELED OFF TO HELP ENSURE NO NATURAL
DRAUGHT IS LOST BELOW BASE (SEE FIG 3)
A NON COMBUSTIBLE HEARTH MUST BE PROVIDED BENEATH THE APPLIANCE WITHIN
THE FIREPLACE OPENING.
A FIRE RESISTANT HEARTH MUST ALSO BE PROVIDED SYMMETRICALLY DISPOSED
ABOUT THE FIREPLACE OPENING A MINIMUM THICKNESS OF 12mm WITH THE
PERIMETER 50mm ABOVE THE FLOOR LEVEL
THE WIDTH MUST EXTEND A MINIMUM OF 150mm EITHER SIDE OF THE FIREPLACE
OPENING AND A DEPTH OF 300mm FROM THE FUEL BED
ANY COMBUSTIBLE MATERIAL MUST BE REMOVED ABOVE THE OPENING TO A HEIGHT
OF 900 mm ABOVE THE HEARTH LEVEL.
PURPOSE BUILT SUPERIMPOSED FIRE RESISTANT HEARTHS AND BACK PANELS,
SPECIFIED AS SUITABLE BY THE MANUFACTURERS MAY BE USED, OR A SUITABLE
PROPRIETARY FIRE SURROUND WITH A 1OO DEGREES C RATING.
CARE SHOULD BE TAKEN TO PREVENT ANY DAMAGE BEING CAUSED TO SURROUNDING
SOFT FURNISHINGS OR DECORATION.
MANY EMBOSSED VINYL WALL COVERINGS MAY BECOME DISCOLOURED IF PLACE TOO
CLOSE TO THE APPLIANCE
CHECK FLUE
CHECK THAT THE CHIMNEY CONFORMS TO THE REQUIRED SPECIFICATIONS AS
ISSUE 1
8
PREVIOUSLY STATED.
EXAMINE THE CONDITION AND CARRY OUT ANY REMEDIAL WORK
IF THE FLUE HAS BEEN USED FOR SOLID FUEL IT MUST BE SWEPT AND A SMOKE TEST
CARRIED OUT TO CHECK THAT SATISFACTORY SMOKE CLEARANCE HAS BEEN
ESTABLISHED.
IF ALL THE SMOKE IS NOT DRAWN INTO THE FLUE , PRE HEAT THE FLUE WITH A BLOW
TORCH OR SIMILAR AND RE CHECK, IF THERE IS ANY UNCERTAINTY EXAMINE FOR THE
CAUSE AND IF NECESSARY SEEK EXPERT ADVICE.
GAS SUPPLY
IT IS RECOMMENDED A CONCEALED CONNECTION IS MADE USING SEMI RIGID TUBING
ON THE LEFT SIDE OF THE APPLIANCE TAKING INTO ACCOUNT THE REQUIREMENTS OF
BS 6891 1988 DEALING WITH ENCLOSED PIPES.
AN ISOLATING VALVE IS BUILT IN TO THE APPLIANCE AS PART OF THE PRESSURE TEST
POINT ELBOW.
SECURE FIRE TO FIREPLACE
MARK POSITION OF FLANGE HOLES, DRILL AND PLUG AND FIX FIRE TO FIREPLACE
ENSURING A GOOD SEAL USING FOAM SEAL SUPPLIED.
CHECKING GAS PRESSURE AND SOUNDNESS
REMOVE THE PRESSURE TEST POINT SCREW FROM THE INLET ELBOW AND CONNECT PRESSURE
GAUGE.
TURN ON GAS TO APPLIANCE.
ROTATE THE CONTROL TO THE IGNITION POSITION AND PUSH IN TO ALLOW THE AIR IN THE
PIPEWORK TO BE PURGED.
PUSH IN PIEZO IGNITION SWITCH
CHECK THAT THE ELECTRODE IS SPARKING.
CONTINUE SPARKING UNTIL PILOT IGNITION IS ESTABLISHED.
TURN THE GAS CONTROL KNOB ON TO THE HIGH POSITION AND ALLOW TO RUN FOR FIVE MINUTES.
CHECK THE INLET PRESSURE IS 20 MBAR. +/- 1MBAR ON NATURAL GAS OR 37 mbar ON PROPANE
CHECK FOR GAS SOUNDNESS.
TURN OFF GAS SUPPLY, DISCONNECT PRESSURE GAUGE AND REPLACE PRESSURE TEST POINT
SCREW.
ISSUE 1
9
COAL BED LAYOUT
PERIODICALLY SMALL DEPOSITS OF SOOT MAY GATHER ON THE FUEL BED AND
BURNER, THIS MUST BE REMOVED BY REMOVING FUEL AND BRUSHING ANY DEPOSITS
WITH A SOFT BRUSH AND VACUUMING THE BURNER, THEN REPLACE FUEL USING THE
FOLLOWING PROCEDURE.
THE MAIN FIBRE BASE IS LIABLE TO HAVE SURFACE CRACKS DUE TO THE HIGH
TEMPERATURES OF THE FIBRE AND THE PAINT BEING DIFFERENT THIS IS QUITE
NORMAL AND SHOULDN’T CAUSE CONCERN
Main ceramic matrix sits on back base central
Front piece sits in to well of burner and flat
onto the curved front of fire tray
Flat and stable
Piece marked underneath 1 sits snugly above
front piece
central and touching left side and right
ISSUE 1
10
The rear piece can be fitted to the top
Sitting central and behind the coal pieces on the
side matrix.
Sitting flat
Piece marked underneath 2 sits flat centrally above
piece 1 onto the flat ledge on the main matrix
Piece 2 should not be touching piece 1 and there
should be a gap of approx 5mm
Final piece marked underneath 3 sits on top of
piece 2 and to the rear pieces
This piece should not actually touch the rear
piece and there should be a gap of approx 5 mm
THE EFFECT CAN ALSO COME AS PEBBLES THE LAYOUT IS EXACTLY THE SAME AS ARE
THE PIECES HOWEVER THE TOP EFFECT LOOKS LIKE PEBBLES RATHER THAN COAL.
ISSUE 1
11
TEST FOR SPILLAGE
CHECK FOR SATISFACTORY CLEARANCE OF COMBUSTION PRODUCTS
CLOSE ALL DOORS AND WINDOWS IN THE ROOMS CONTAINING THE FIRE
TURN ON GAS FIRE AND SET THE CONTROL TO HIGH
LEAVE THE FIRE BURNING FOR FIVE MINUTES AND INSERT A LIGHTED SMOKE MATCH
ON A VERTICAL PLANE
50 mm DIRECTLY UNDER FRONT EDGE OF CANOPY AND 50mm FROM EITHER SIDE OF THE
OPENING
ALL SMOKE MUST BE DRAWN INTO THE FLUE
IF SPILLAGE OCCURS ALLOW A FURTHER TEN MINUTES
SHOULD SPILLAGE STILL OCCUR TURN OFF THE FIRE AND SEEK
EXPERT ADVICE
IF AN EXTRACTOR FAN IS SITUATED IN THE ROOM , THIS TEST SHOULD BE REPEATED
WITH THE FAN RUNNING
IF THERE IS A ROOM WITH AN EXTRACTOR FAN, THE TEST SHOULD BE REPEATED WITH
ALL THE DOORS TO THAT ROOM OPENED AND THE EXTRACTOR FAN RUNNING
FITTING TRIMS
Fit The Trim With Four Magnets Placed On The Vertical Side Flanges Of The Firebox (One At The Top And One At The
Bottom)
Offer The Trim Up And Push Into Position
Place Fret Centrally In Front To Cover The Controls
INSTRUCT USER
DEMONSTRATE THE LIGHTING AND EXTINGUISHING PROCEDURES TO THE USER AND REMOVAL AND
REFITTING OF THE TRIM FOR CLEANING.
THE APPLIANCE SHOULD BE OPERATED WITH THE GAS CONTROL NOT TURNED ON MORE THAN LOW FOR
THE FIRST FIVE HOURS OF USE TO ALLOW THE FIBRE FUEL TO CURE SLOWLY.
THE CURING EFFECT OF HEATING THE FUEL AND OTHER CERAMICS COMPONENTS WILL CAUSE AN
INITIAL ODOR.
THE APPLIANCE SHOULD BE SERVICED ANNUALLY BY A COMPETENT PERSON IN ACCORDANCE WITH
THESE INSTRUCTIONS AND THE APPLIANCE CHECKED FOR SPILLAGE IN ACCORDANCE WITH THE
METHOD DETAILED IN THESE INSTRUCTIONS
HAND THESE INSTRUCTIONS TO THE USER.
ISSUE 1
12
SERVICING NOTES
GENERAL NOTES.
SERVICING SHOULD BE CARRIED OUT ANNUALLY BY A COMPETENT PERSON SUCH AS A REGISTERED
PERSON IN ACCORDANCE WITH THE RELEVANT REGULATIONS, TO ENSURE THE SAFE AND CORRECT
OPERATION OF THE APPLIANCE
BEFORE COMMENING ANY SERVICE OR REPLACEMENT OF PARTS TURN OFF GAS SUPPLY TO FIRE
AFTER SERVICING CHECK FOR GAS SOUNDNESS
AT LEAST ONCE A YEAR CHECK FOR DEBRIS
IF SOOT HAS ACCUMULATED CHECK TO ESTABLISH CAUSE AND RECTIFY IF NECESSARY CLEAN FLUE OR
CHIMNEY ACCORDINGLY
EXAMINE THE FUEL FOR SIGNS OF CRACKING AND REPLACE IF NECESSARY. SEE FUEL LAYOUT
PROCEDURE BEFORE ATTEMPTING TO REPLACE FUEL WHICH SHOULD ONLY BE REPLACED AS A
COMPLETE SET WITH NO EXTRA FUEL ADDED.
1 REMOVAL OF FUEL PIECES
REMOVE LOOSE FUEL PIECES
REMOVE FRONT FIBRE BASE
REMOVE MAIN FIBRE BASE
2 REPLACEMENT OF GAS CONTROL
REMOVE FUEL SET AS 1
DISCONNECT FIRE AT INLET ELBOW
REMOVE FIRETRAY BY UNSCREWING TWO SCREWS AT FRONT BOTTOM SECTION OF
FIRE TRAY
REMOVE CONTRO KNOB,DISCONNECT GAS CONNECTIONS TO VALVE INCLUDING PILOT
CONNECTION AND THERMOCOUPLE CONNECTION
REMOVE LOCKNUT HOLDING GAS CONTROL TO FRONT BOTTOM SECTION .
RE ASSEMBLE IN REVERSE ORDER
TURN ON GAS SUPPLY.CHECK FOR SOUNDNESS AND RE COMMISION APLIANCE
3 REPLACEMENT OF INJECTOR
REMOVE FUEL PIECES SEE 1
REPEAT 2 REMOVE GAS CONTROL
DISCONNECT GAS CONNECTION TO INJECTOR
UNSCREW INJECTOR “B” WHILST AT THE SAME TIME HOLDING LOCKNUT WITH A
SPANNER AND CLEAN OR REPLACE.
SEE DIAGRAM BELOW.
ISSUE 1
13
RE ASSEMBLE IN REVERSE ORDER
TURN ON GAS SUPPLY. CHECK FOR SOUNDNESS AND RECOMMISION THE FIRE.
REPLACEMENT OXY PILOT ASSEMBLY
DISCONNECT FIRE AT INLET ELBOW
REMOVE FIRETRAY
DISCONNECT THERMOCOUPLE AT GAS VALVE
DISCONNECT GAS CONNECTION FROM PILOT ASSEMBLY
REMOVE IGNITOR LEAD FROM PILOT ASSEMBLY
UNDO SCREWS SECURING OXY PILOT TO FIRETRAY
RE-ASSEMBLE IN REVERSE ORDER
TURN ON GAS SUPPLY,CHECK FOR SOUNDNESS AND RE-COMMISION APPLIANCE
CLEANING
BEFORE CLEANING ANY PART OF THE FIRE ,ENSURE THAT THE GAS IS TURNED OFF AND
FIRE IS COOL.
BLACK PAINT.
USE ONLY CLEAN DAMP CLOTH ,DO NOT USE ANY CLEANING AGENTS
BRASS TRIM
USE BRASSO ENSURING YOU REMOVE THE BRASS TRIM FROM THE APPLIANCE BEFORE
CLEANING
IMPORTANT
THE PAINT AND BRASS FINISH ARE DURABLE BUT WILL BE DAMAGED IF
PLASTER,CEMENT,OR WALLPAPER PASTE COMES IN CONTACT WITH IT
COALS AND CERAMICS
IF FOR ANY REASON IT IS NECCESARY TO REMOVE CERAMIC PARTS,THEN BEFORE
REPLACEMENT THE BURNER SHOULD BE CHECKED THAT NO PARTICLES HAVE
DEPOSITED ON THE BURNER AND IF NECCESARY VACUUM THEM CAREFULLY,THEN
REFER TO INSTRUCTIONS FOR REPLACING CERAMICS.
CERAMICS SHOULD BE CLEANED BY SHAKING ANY DEBRIS
NO BRUSHING OR VACUUMING SHOULD BE PERFORMED .
INSTALLER SPARE PARTS
FUEL BED
FRONT FIBRE
BRASS TRIM
GAS VALVE
REMOTE ODS
GEM001
GEM003
GEM 005
GEM 007
GEM 009
MAIN MATRIX
GEM002
INSTUCTIONS
GEM 004
ODS COMPLETE GEM006
REMOTE GAS VALVE GEM 008
ISSUE 1
14
CRYSTAL FIRES
1 BECHERS DRIVE
AINTREE RACECOURSE
BUSINESS PARK
AINTREE
LIVERPOOL
L9 5AY
GEM
DECORATIVE FUEL EFFECT GAS FIRE
THIS APPLIANCE IS CATEGORY I2H FOR USE
WITH NATURAL GAS AT A SUPPLY
PRESSURE OF 20 mbar OR CATEGORY I3P
FOR USE WITH PROPANE AT A SUPPLY
PRESSURE OF 37mbar
G.B. AND I.E.
USERS INSTUCTIONS
ISSUE 1
15
USERS INSTRUCTIONS FOR GEM GAS APPLIANCE
YOUR GEM GAS APPLIANCE IS A DECORATIVE LIVE FUEL EFFECT GAS FIRE ,DUE TO ITS
NEWNESS THE FIRE MAY GIVE OFF SLIGHT SMELL FOR A SHORT PERIOD AFTER
INSTALLATION .THIS IS QUITE NORMAL AND WILL DISAPPEAR AFTER A FEW HOURS OF
OPERATION.
THE APPLIANCE TO WHICH THESE INSTRUCTIONS APPLY MUST BE INSTALLED BY A
COMPETENT PERSON(EG. A REGISTERED INSTALLER IN ACCORDANCE WITH THE
CURRENT EDITION OF THE GAS SAFETY INSTALLATIONS AND USE REGULATIONS OR
THE RULES IN FORCE)APPROVED BY THE HEALTH AND SAFETY EXECUTIVE AND MUST
BE IN ACCORDANCE WITH THE INSTALLATION AND SERVICING INSTUCTIONS SUPPLIED.
SERVICING SHOULD BE CARRIED OUT REGULARLY BY A COMPETENT PERSON ( EG A
REGISTERED INSTALLER)IN ACCORDANCE WITH THE CURRENT EDITION OF THE GAS
SAFETY (INSTALLATION AND USE) REGULATIONS OR THE RULES IN FORCE.TO ENSURE
THE CORRECT AND SAFE OPERATION OF THE APPLIANCE .DEBRIS SHOULD ALSO BE
REMOVED FROM BEHIND THE APPLIANCE AT REGULAR INTERVALS.
BEFORE INSTALLATION OF THE APPLIANCE THE CHIMNEY MUST BE SWEPT AND THEN
INSPECTED REGURLARLY TO ENSURE THAT IT REMAINS FREE OF OBSTRUCTION.
A FIRE GUARD COMPLYING TO BS8423 ,MUST BE FITTED IF THE ROOM WILL BE
OCCUPIED BY YOUNG CHILDREN THE ELDERLY ,OR INFIRM PEOPLE. ON NO ACCOUNT
MUST ANY RUBBISH BE THROWN ON TO THE FIRE OR THE LAYOUT OF THE FIREBED
DISTURBED.
OPERATING INSTRUCTIONS.
THE APPLIANCE DATA BADGE IS POSITIONED ON THE FRONT BOTTOM SECTION OF THE APPLIANCE AND
CARIES THE CONTROL KNOB POSITIONS.THE FULL LIGHTING PROCEDURE IS AS FOLLOWS.
1.PUSH CONTROL KNOB IN AS FAR AS POSSIBLE ON GAS CONTROL
2.TURN KNOB ANTICLOCKWISE TO IGNITION POSITION STILL KEEPING KNOB IN AS FAR AS POSSIBLE.
3.THE IGNITION BUTTON WILL IGNITE THE PILOT WITH THIS OPERATION KEEP THE KNOB PRESSED IN FOR
15 SECONDS.IF THE PILOT FAILS TO LIGHT TURN THE CONTROL KNOB CLOCKWISE TO THE OFF POSITION,
WAIT 3 MINUTES AND REPEAT THE PROCEDURE
4.WHEN THE PILOT FLAME IS ALIGHT THE CONTROL KNOB SHOULD BE ALLOWED TO SPRING OUT
SLIGHTLY.TURN THE KNOB FULLY ANTICLOCKWISE TO THE HIGH POSITION.THE PILOT FLAME WILL THEN
IGNITE THE MAIN BURNER.THE PILOT FLAME CAN BE VIEWED TO THE RIGHT OF THE FIRE JUST BEHIND
THE FRONT LOG SET
5.THE APPLIANCE CAN BE ADJUSTED BETWEEN HIGH AND LOW BY MOVING THE CONTROL KNOB TO
SUIT,THE KNOB WILL NEED TO BE DEPRESSED SLIGHTLY TO MOVE FROM LOW HIGH AND IGNITION.
6.TO TURN THE FIRE OFF,DEPRESS THE KNOB SLIGHTLY AND TURN IT TO PILOT POSITION.
7.TO COMPLETELY EXTINGUISH THE FIRE DEPRESS THE KNOB SLIGHTLY AND TURN TO OFF POSITION.
8.SHOULD THE SPARK IGNITION FAIL TO OPERATE.TURN THE CONTROL KNOB TO THE OFF POSITION AND
WAIT 3 MINUTES.TURN THE KNOB TO THE IGNITION POSITION AND THEN LIGHT THE PILOT WITH A
TAPER.”LIGHTING THE PILOT WITH A TAPER IS AN EMERGENCY MEASURE ONLY AND THE APPLIANCE
SHOULD BE SERVICED AS SOON AS POSSIBLE”.AND THEN PROCEED AS STATED IN PARAGRAPHS 2/7.
IMPORTANT .THIS APPLIANCE IS FITTED WITH AN OXYGEN DEPLETION SENSOR INCORPORATED INTO
THE PILOT BODY.SHOULD THE FIRE REEATEDLY EXTINGUISH ITSELF THEN SPECIALIST ADVISE SHOULD
BE SOUGHT,AS THIS MAY INDICATE SPILLAGE INTO THE ROOM OF COMBUSTION PRODUCTS.
ISSUE 1
16
MERTIK MAXITROL REMOTE CONTROL SYSTEM
THESE INSTRUCTIONS ARE FOR THE USE ON CRYSTAL FIRES REMOTE CONTROL RANGE
OF GAS FIRES
ON POSITION
OFF POSITION
IGNITION /PILOT
POSITION
A
OPERATION
FIGURE 1
B
LIGHTING PROCEDURE
1. TURN KNOB A (FIGURE 1) SLIGHTLY LEFT TOWARDS THE IGNITION
POSITION(SHOWN IN FIG 1 ABOVE) UNTIL REACHING STOP,PRESS DOWN AND
HOLD FOR FIVE SECONDS
(ONLY PILOT GAS FLOWS)
2. CONTINUE PRESSING DOWN KNOB A WHILE TURNING FURTHER LEFT TO
ACTIVATE PIEZO,CONTINUE TO HOLD DOWN FOR 10 SECONDS AFTER PILOY HAS
BEEN LIT,IF PILOT DOES NOT LIGHT,STEPS 1 AND 2 CAN BE REPEATED
IMMEDIATELY.
3. UPON LIGHTING,RELEASE KNOB A AND TURN FURTHER LEFT TO ON POSITION
(SHOWN IN FIGURE 1 ABOVE)PILOT GAS FLOWS AND MAIN BURNER FLOWS IN
ACCORDANCE TO THE TEMPERATURE SETTING(KNOB B AS SHOWN IN FIG 1
ABOVE)
ADJUSTING THE FLAME
SETTINGS
TO TURN THE FIRE ON AND/OR TO ADJUST THE
FLAME STTING, PRESS THE ON BUTTONS ON THE
REMOTE HANDSET.CONTINUE PRESSING UNTIL
DESIRED FLAME SETTING IS OBTAINED.PRESS
AND HOLD THE OFF BUTTON TO REVERSE THE
SETTING.THE RECEIVER IS EQUIPPED WITH A
BUILT IN DELAY, RECOGNIZABLE BY THE FLICKERING
LIGHT,TO FACILITATE FINE ADJUSTMENT OF THE FLAME
THE MOTORIZED VALVE IS EQUIPPED WITH A SLIP
CLUTCH ,ALLOWING MANUAL ADJUSTMENT OF MAIN
GAS BY TURNING KNOB B
ON BUTTONS
TO PRESS THE ON BUTTON
YOU MUST PRESS THE 2
BUTTONS TOGETHER
ISSUE 1
17
OFF BUTTON
SHUT OFF PROCEDURE
1.TURN KNOB A RIGHT UNTIL REACHING STOP. IN THIS POSITION ONLY PILOT GAS
FLOWS
2.TO SHUT OFF VALVE COMPLETELY,PRESS DOWN SLIGHTLY AND CONTINUE TURNING
RIGHT FROM PILOT POSITION TO THE OFF POSITION.THE SAFETY INTERLOCK PREVENTS
RE-IGNITION OF THE PILOT FLAME UNTIL THERMOCOUPLE HAS COOLED DOWN
SUFFICIENTLY(ELAPSED TIME WILL VARY BASED ON THERMOCOUPLE TYPE)
3.SWITCHING OFF THE REMOTE IS NOT NECCESARY.
THE SENSOR AND BATTERY HOLDER A INSERTED BENEATH THE RIGHT SIDE OF THE
FIRE.TO REPLACE BATTERIES ALLOW FIRE TO COOL FOR AT LEAST 30 MINUTES THEN
PULL OUT BATTERY HOLDER, THE COVER CAN SLIDE OFF AS ABOVE AND THE
BATTERIES CAN BE REPLACED.(USE ONLY LIKE FOR LIKE ALKALINE AA BATTERIES)
REPLACEMENT PARTS
BATTERY HOLDER AND SENSOR
GAS VALVE
REMOTE HANDSET
CRYSMERTIKHOLDER
CRYSMERTIKVALVE
CRYSMERTIKHANDSET
ISSUE 1
18
CLEANING
BEFORE CLEANING ANY PART OF THE FIRE ,ENSURE THAT THE GAS IS TURNED OFF AND
FIRE IS COOL.
BLACK PAINT.
USE ONLY CLEAN DAMP CLOTH ,DO NOT USE ANY CLEANING AGENTS
BRASS TRIM
USE BRASSO,ENSURING YOU REMOVE THE BRASS TRIM FROM THE APPLIANCE BEFORE
CLEANING
IMPORTANT
THE PAINT AND BRASS FINISH ARE DURABLE BUT WILL BE DAMAGED IF
PLASTER,CEMENT,OR WALLPAPER PASTE COMES IN CONTACT WITH IT
COALS AND CERAMICS
IF FOR ANY REASON IT IS NECCESARY TO REMOVE CERAMIC PARTS,THEN BEFORE
REPLACEMENT THE BURNER SHOULD BE CHECKED THAT NO PARTICLES HAVE
DEPOSITED ON THE BURNER AND IF NECCESARY VACUUM THEM CAREFULLY,THEN
REFER TO INSTRUCTIONS FOR REPLACING CERAMICS.
CERAMICS SHOULD BE CLEANED WITH A SOFT BRUSH
THE TAPER SHOULD BE
POSITIONED TO THE PILOT TO
THE FAR RIGHT OF CURVED
FRONT PIECE AND LEVEL
WITH PIECE 1
SHOWN LEVEL WITH THE LINE
BELOW
-----------------------------
THE GEM CAN BE LIT WITH A TAPER SHOULD THE SPARK IGNITION FAIL
TURN THE KNOB TO THE OFF POSITION AND WAIT 3 MINUTES TURN THE KNOB TO THE
IGNITION POSITION AND THEN LIGHT THE PILOT WITH A TAPER
THIS IS ONLY AN EMERGENCY MEASURE AND THE APPLIANCE SHOULD BE
SERVICED AS SOON AS POSSIBLE,THEN PROCEED AS STATED EARLIER FOR OPERATION
ISSUE 1
19
COAL BED LAYOUT
PERIODICALLY SMALL DEPOSITS OF SOOT MAY GATHER ON THE FUEL BED AND
BURNER, THIS MUST BE REMOVED BY REMOVING FUEL AND BRUSHING ANY DEPOSITS
WITH A SOFT BRUSH AND VACUUMING THE BURNER, THEN REPLACE FUEL USING THE
FOLLOWING PROCEDURE.
Main ceramic matrix sits on back base central
Front piece sits in to well of burner and flat
onto the curved front of fire tray
Flat and stable
Piece marked underneath 1 sits snugly above
front piece
central and touching left side and right
ISSUE 1
20
The rear piece can be fitted to the top
Sitting central and behind the coal pieces on the
side matrix.
Sitting flat
Piece marked underneath 2 sits flat centrally above
piece 1 onto the flat ledge on the main matrix
Piece 2 should not be touching piece 1 and there
should be a gap of approx 5mm
Final piece marked underneath 3 sits on top of
piece 2 and to the rear pieces
This piece should not actually touch the rear
piece and there should be a gap of approx 5 mm
THE EFFECT CAN ALSO COME AS PEBBLES THE LAYOUT IS EXACTLY THE SAME AS ARE
THE PIECES HOWEVER THE TOP EFFECT LOOKS LIKE PEBBLES RATHER THAN COAL.
FUEL BED
FRONT FIBRE
BRASS TRIM
GEM001
GEM 003
GEM 005
CUSTOMER SPARE PARTS
MAIN MATRIX
GEM002
INSTUCTIONS
GEM 004
ISSUE 1
21
REAR MATRIX SITS BEHIND 2 LUGS AND FLAT
ON BASE SEE BELOW
GEM LOOSE COAL SET UP
FRONT FIBRE SITS IN WELL OF BURNER AS ABOVE
NEXT 2 SIT AS ABOVE AGAIN WITH
THE POINTS OF THE COALS LOOKING OUTWARDS
FRONT 4 LOOSE COALS SIT AS ABOVE
FINAL 3 SIT CENTRALLY ON TOP
AS ABOVE
NEXT SET OF 3 FIT AS SHOWN ABOVE WITH
THE LEFT AND RIGHT HAVING THE POINT OF THE
COAL POINTING OUTWARDS
Download PDF