Quadra-Fire | Direct Vent Gas Appliance COLBAY-FS-B | Owner`s manual | Quadra-Fire Direct Vent Gas Appliance COLBAY-FS-B Owner`s manual

R
COLUMBIA BAY
DIRECT VENT GAS APPLIANCE
Tested and
Listed by
Owner’s Manual
O-T L
Portland
Oregon USA
US
C
OMNI-Test Laboratories, Inc.
Installation and Operation
Model:
COLBAY-FS-B
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating and • Read, understand and • Leave this manual with
follow these instructions
maintenance instructions
party responsible for use
for safe installation and
included.
and operation.
operation.
fire
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- Do not try to light any appliance.
Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory-trained
professionals, or technicians supervised by an NFI
certified professional.
Page 1
D
DI O N
SC O
AR T
D
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
fl
• Keep clothing, furniture, draperies and other flammable
materials away.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber or gas
fitter.
See Table of Contents for additional Commonwealth of Massachusetts requirements.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer's instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
and Welcome to the Quadra-Fire Family!
Hearth & Home Technologies welcomes you to our tradition
of excellence! In choosing a Quadra-Fire appliance, you
have our assurance of commitment to quality, durability, and
performance.
meticulously fabricated and gold and nickel surfaces are
hand-finished for lasting beauty and enjoyment. Our pledge
to quality is completed as each model undergoes a quality
control inspection. From design, to fabrication, to shipping:
Our guarantee of quality is more than a word, it’s QuadraFire tradition, and we proudly back this tradition with a Limited Lifetime Warranty.
This commitment begins with our research of the market,
including ‘Voice of the Customer’ contacts, ensuring we
make products that will satisfy your needs. Our Research
and Development facility then employs the world’s most
advanced technology to achieve the optimum operation of
our stoves, inserts and fireplaces. And yet we are old-fashioned when it comes to craftsmanship. Each appliance is
We wish you and your family many years of enjoyment in the
warmth and comfort of your hearth appliance. Thank you for
choosing Quadra-Fire.
SAMPLE OF SERIAL NUMBER / SAFETY LABEL
LOCATION: ON BACK OF APPLIANCE
MODEL / MODÈLE:
COLUMBIA BAY
800 West Jefferson Street
Lake City, MN 55041
www.quadrafire.com
FOURNAISE AU GAZ AVEC VENTILATION
NE PAS UTILISER AVEC LE COMBUSTIBLE SOLIDE
APPROVED FOR CANADA AND USA TO:
ANSI Z21.88a-2001 / CSA 2.33a-M01 Vented Gas Fireplace Heaters, and applicable
sections of UL307b Gas Burning Heating Appliances for Manufactured Homes
and Recreational Vehicles, CAN/CGA 2.17-M91 “Gas Fired Appliances for use
at High Altitudes.” This appliance is manufactured for operation with Natural
Gas. For conversion to propane Manufacturer’s Part #842-4041 and instructions
must be used. This appliance may be installed in a bedroom or bedsitting room;
in Canada remote thermostat installation is required.
FAN TYPE VENTED CIRCULATOR / VENTILATEUR CIRCULATOIRE
Blower Electrical Rating / Évaluation du Ventilateur Électrique:
115 V., 1.5 Amps, 60 Hz, 150 Watts
APPROUVÉ POUR LE CANADA ET LES ÉTATS-UNIS:
ANSI Z21.88a-2001 / CSA 2.33a-M01 Fournaises au Gaz avec Ventilation, et les sections
applicable de UL 307b Appareils de Chauffage Au Gaz pour les Maisons Mobiles et les
Véhicules Motorisés, CAN/CGA 2.17-M91 “Gas Fired Appliances for use at High Altitudes”.
Cet appareil est manufacturé pour l’opération avec le Gaz Naturel. Pour une conversion
au gaz propane les pièces du Manufacturier #842-4041 et ses instructions doivent être
utilisées. Cet appareil peut être utilisé dans une chambre à coucher ou salle de séjour; au
Canada, l’installation d’un thermostat à distance est exigée.
A
E
D
l’Alcôve
PL
M
SA
This appliance must be properly connected to a venting system in accordance with the manufacturer's installation instructions.
Cet apprareil doit être correctement raccordé à un système d'évacuation, conformément aux instructions du fabricant.
Keep burner and control compartment clean. See installation and operating instructions accompanying this appliance. This vented gas fireplace heater is not for use with air filters.
Due to high surface temperatures, keep children, clothing and furniture away.
Gardez le brûleur et le compartiment de contrôle propres. Vérifiez les instructions d’installation et d’opération qui accompagnent cet appareil. Cet appareil de chauffage au gaz n’est
pas pour l’usage avec des filtres d’air. Du aux surfaces de températures élevées, gardez les enfants, les vêtements et les meubles à distance éloignée.
Jan
H
Alcove height
This appliance must be installed in accordance with the current Standard CAN/CSA Z240 MH, Mobile Housing or with Manufactured Home Construction and Safety Standard,
Title 24 CFR, Part 3280, or when such standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installation Standard.
WARNING: Do not operate the appliance until all sections have been assembled and installed in accordance with the manufacturer's instructions.
Installer l'appareil selon la norme CAN/CSA-Z240, Serie MM, Maisons mobiles ou la norme 24 CFR Part 3280, Manufactured Home Construction and Safety Standard. Si ces
normes ne sont pas pertineutes, utilisez la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard.
AVERTISSEMENT: Ne pas utiliser l'appareil tant que toutes les sections n'ont pas ete assemblees et installees selon les instructions du fabricant.
2007
E
C
G- Hauteur De
For use with Propane
Usage Au Gaz Propane
0-2000’
30,000
24,500
25,800
.0635 (52 DMS)
11”
14”
10”
This appliance must be installed in accordance with local codes, if any (and Commonwealth of Massachusetts approved); if none, follow the National Fuel Gas Code, ANSI
Z223.1 or Canadian Installation Codes, CAN/CGA-B149. Install and use only in accordance with manufacturer’s installation and operating instructions. NOTE: Have the gas
supply line installed in accordance with local building codes by a qualified installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts,
installation must be performed by a licensed plumber or gas fitter.)
Cet appareil doit être installé en accord avec les codes locaux, s’il-y-a lieu (et approuvé par dans la République de Massachusetts); sinon lisez ANSI Z223.1/CAN 1-B149.
Installez et utilisez en accords avec les instructions d’installation et d’opération du manufacturier. REMARQUE: Le conduit gaz doit être installé conformément aux codes
de construction locaux. L'installation doit être effectuée par un technicien qualifeé et/ou muni d'une licence de manière à respecter les règlements municipaux. (Dans la
République de Massachusetts, l'installation doit être effectuée par un plombier ou un installateur d'appareils à gaz agrée.)
2006
Date of Manufacture / Date du Manufacturier
Feb
Mar
Apr
May
Jun
Jul
Aug
Sep
Oct
Nov
A*
A*
F
A. Side of stove top to side wall
6 in. (152 mm)
Du coté du poêle au coté du mur
A*. In an Alcove
6-3/4 in. (171 mm)
Dans l’alcôve
B. Rear of control box to back wall
2 in. (51 mm)
Le contrôle arrière au mur arrière
C. Flue pipe to back wall
6 in. (152 mm)
Du tuyau de cheminée au mur arrière
D. Flue pipe to side wall
14 in. (356 mm)
Du tuyau de cheminée au mur du coté
E. Rear corner of stove top to side wall
2 in. (51 mm)
Du coin arrière du poêle au mur de coté
F. Min. Floor to ceiling height (std. room)
84 in. (2134 mm)
Hauteur minimum du plancher au plafond (pièce standard)
G. Top of stove to alcove ceiling
19 in. (483 mm)
Du dessus du poêle au plafond de l’alcôve
H. Maximum alcove depth
36 in. (914 mm)
Profondeur maximum de l’alcôve
I. Minimum alcove width
36 in. (914 mm)
Largeur minimum de l’alcôve
HEARTH: A non-combustible hearth pad is not required. However, the
floor beneath the stove must be stable, level, and strong enough to support
the stove without a tipping hazard.
CHEMINÉE: Un coussinet non-combustible de cheminée n’est pas
exigé. Cependant, le plancher en dessous du poêle doit être droit, à
niveau et assez fort pour supporter le poêle sans le hasard de
basculer.
Dec
DO NOT REMOVE THIS LABEL / NE PAS
ENLEVER L’ÉTIQUETTE
Made in U.S.A. / Fait Aux États-Unis
250-5184
Page 2
Barcode
I
B
P.4.1-02 Canada Minimum pipe (P.4.1-02 Le canada tuyau minimum) 65.42% NG / 65.96% LP
Puissance Évaluée à “HI” (BTU/Hr)
Puissance Évaluée à “LO” (BTU/Hr)
Puissance Maximum (BTU/Hr)**
Orifice du Brûleur Principal
Pression Minimum de la Valve (pouces W.C.)
Pression Maximum de la Valve (pouces W.C.)
Pression du Collecteur d’ Échappement à “HI”
(pouces W.C.)
**Max Venting, Blower On
** Ventilation Maximum, Ventilateur Allumé
This appliance equipped only for altitudes 0-2000’ (0-610m) in USA; and in Canada for altitudes of 0-4500’ (0-1370m). In USA for Altitudes above 2000’, the vent
configuration, orifice, or combination of both may need to be changed. See Owner’s Manual for information on making these changes.
Cet appareil est équipé pour les altitudes de 0-2000’ (0-610m) aux États-Unis; et au Canada pour les altitudes de 0-4500’ (0-1370m). Pour les altitudes au dessus de 2000’
aux États-Unis, la configuration du ventilateur, son orifice ou les deux peuvent possiblement avoir à être changé. Voyez le manuel du propriétaire pour les informations
sur ces changements.
2005
Minimum clearances required from combustible construction for all
appliance surfaces.
Espaces minimum exigés de la construction combustible aux surfaces
de l’appareil.
Thermal Efficiency / Efficacité Thermique*
84% NG (blower on / avec ventilateur allumé)
86% LP (blower on / avec ventilateur allumé)
* With Maximum horizontal length. / Avec longueur horizontale maximum.
For use with Natural Gas
Usage Au Gaz Naturel
0-2000’
30,000
21,000
25,250
.1065 (36 DMS)
4.5”
7.0”
3.5”
Top Vent: Input Rate on “HI” (BTU/Hr)
Input Rate on “LO” (BTU/Hr)
Maximum Output (BTU/Hr)**
Main Burner Orifice
Minimum Inlet Pressure (Inches W.C.)
Maximum Inlet Pressure (Inches W.C.)
Manifold Pressure on “HI” (Inches W.C.)
MINIMUM CLEARANCES TO COMBUSTIBLES
ESPACE MINIMUM AUX COMBUSTIBLES
VENTED GAS FIREPLACE HEATER.
NOT FOR USE WITH SOLID FUEL
E
Report / Rapport
061-S-19b-5
SERIAL NO.
002
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Date
- TABLE OF CONTENTS -

A.
B.
C.
D.
E.
F.
G.
H.
Appliance Certifications ......................4
Glass Specifications ............................4
BTU Specifications ..............................4
High Altitude Installations ....................4
Non-Combustible Materials .................4
Combustible Materials ........................4
Electrical Codes ..................................4
Requirements for the
Commonwealth of Massachusetts ......5
A. Design & Installation
Considerations ....................................6
B. Tools and Supplies Needed................6
C. Inspect Appliance & Components .......6
A. Selecting Appliance Location..............7
B. Clearances to Combustibles ...............7
A. Vent Termination Minimum
Clearances..........................................8
A. Recommendation for Wire ..................26
B. Connecting to the Appliance ...............26
C. Standing Pilot Ignition
System Wiring .....................................26
Section 8: Appliance Setup
A. Remove Shipping Materials ................28
B. Accessories .........................................28
C. Door Crown Installation .......................28
D. Brick Installation ..................................28
E. Positioning the Logs ............................29
F. Mineral Wool .......................................30
G. Glass Door Replacement ....................30
H. Blower Installation ...............................31
I. Vertical Damper Adjustment ...............32
J. Shutter Adjustment .............................32
A.
B.
C.
D.
E.
Before Lighting Appliance ...................33
Controls ...............................................33
Lighting Appliance ...............................34
After Appliance is Lit ...........................35
Frequently Asked Questions ...............35
...............................36
A.
B.
C.
D.
E.
F.
G.
Venting Components ..........................10
Use of Elbows .....................................10
Measuring Standards ..........................10
How to Use the Vent Graph ................11
Venting Guidelines ..............................11
Horizontal Termination ........................12
Vertical Termination ............................15
A. Fuel Conversions ................................22
B. Gas Pressures ....................................24
C. Gas Connection.. ................................24
A. Maintenance Tasks .............................39
B. Service and Maintenance Log ............40
A.
B.
C.
D.
E.
F.
Appliance Dimension Diagram ...........41
Vent Components Diagram ................42
Vent Components List ........................43
Service Parts List ................................44
Warranty .............................................47
Contact Information ............................49
= Contains updated information.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 3
1
fications
fication
MODEL:
Columbia Bay FS
LABORATORY:
OMNI Test Laboratories, Inc.
061-S-17b-5
TYPE:
Direct Vent Gas Heater
STANDARD:
ANSI Z21.88a-2000ּCSA 2.33a-M00
ּUL307bּCAN/CBA 2.17-M91
Model
The product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burning
Heating Appliances for Manufactured Homes and Recreational Vehicles” and "Gas Fired Appliances for use at High
Altitudes".
Manufactured Home or Mobile Home installation may occur
only after the home is site located and must conform with
the Manufactured Home Construction and Safety Standard,
Title 24 CFR, Part 3280, or, when such a standard is
not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or Standard for Gas
Equipped Recreational Vehicles and Mobile Housing, CSA
Z240.4.
When installed, the appliance must be electrically grounded
in accordance with local codes or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70, or
the Canadian Electrical Code, CSA C22.1.
fications
This appliance is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
NOTE: This installation must conform with local codes. In the
absence of local codes you must comply with the National
in the U.S.A.
and the CAN/CGA B149 Installation Codes in Canada.
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the unit and to replace any part of the control system and
any gas control which has been under water.
Page 4
(US or Canada)
Maximum
Input BTU
Minimum
Input
BTU
Orifice
Size
(DMS)
*Efficiency
Up To
%
**P.4
%
30,000 21,000
36
84
73.3

30,000 24,500
52
86
75.1

* Thermal efficiency maximum pipe with blower on.
** Canada minimum pipe.
Omni-Test Laboratories listed gas appliances are tested and
approved without requiring changes for elevations from 0 to
2000 feet in the U.S.A. and 0 to 4500 feet in Canada.
When installing this appliance at an elevation above 2000
feet, it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Input
rate should be reduced by 4% for each 1000 feet above a
2000 foot elevation in the U.S.A. If the heating value of the
gas has been reduced, these rules do not apply. To identify
the proper orifice size, check with the local gas utility.
If installing this appliance at an elevation above 4500 feet (in
Canada), check with local authorities.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a Vertical
Tube Furnace at 750°C, shall be considered non-combustible
materials.
Materials made of or surfaced with wood, compressed
paper, plant fibers, plastics, or other materials that can ignite
and burn, whether flame proofed or not, or whether plastered
or unplastered shall be considered combustible materials.
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA 70latest edition or the
• A 110-120 VAC circuit for this product must be protected with
ground-fault circuit-interrupter protection, in compliance with
the applicable electrical codes, when it is installed in locations
such as in bathrooms or near sinks.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
NOTE: The following requirements reference various
Massachusetts and national codes not contained in this
document.
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in whole
or in part for residential purposes, including those owned or
operated by the Commonwealth and where the side wall
exhaust vent termination is less than seven (7) feet above
finished grade in the area of the venting, including but not
limited to decks and porches, the following requirements
shall be satisfied:
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter shall
observe that a hard wired carbon monoxide detector with an
alarm and battery back-up is installed on the floor level where
the gas equipment is to be installed. In addition, the installing
plumber or gas fitter shall observe that a battery operated or
hard wired carbon monoxide detector with an alarm is installed
on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to
secure the services of qualified licensed professionals for the
installation of hard wired carbon monoxide detectors.
Inspection
The state or local gas inspector of the side wall horizontally
vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon
monoxide detectors and signage installed in accordance with
the provisions of 248 CMR 5.08(2)(a) 1 through 4.
The following equipment is exempt from 248 CMR 5.08(2)(a)
1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition of
NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled
equipment installed in a room or structure separated from
the dwelling, building or structure used in whole or in part
for residential purposes.
MANUFACTURER REQUIREMENTS
When the manufacturer of Product Approved side wall
horizontally vented gas fueled equipment provides a venting system design or venting system components with the
equipment, the instructions provided by the manufacturer for
installation of the equipment and the venting system shall
include:
• Detailed instructions for the installation of the venting system design or the venting system components; and
In the event that the side wall horizontally vented gas fueled
equipment is installed in a crawl space or an attic, the hard
wired carbon monoxide detector with alarm and battery backup may be installed on the next adjacent floor level.
• A complete parts list for the venting system design or
venting system.
In the event that the requirements of this subdivision can not
be met at the time of completion of installation, the owner shall
have a period of thirty (30) days to comply with the above
requirements; provided, however, that during said thirty (30)
day period, a battery operated carbon monoxide detector with
an alarm shall be installed.
When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the
parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by
the manufacturer:
Each carbon monoxide detector as required in accordance
with the above provisions shall comply with NFPA 720 and
be ANSI/UL 2034 listed and IAS certified.
A metal or plastic identification plate shall be permanently
mounted to the exterior of the building at a minimum height
of eight (8) feet above grade directly in line with the exhaust
vent terminal for the horizontally vented gas fueled heating
appliance or equipment. The sign shall read, in print size no
less than one-half (1/2) inch in size, “GAS VENT DIRECTLY
• The referenced “special venting system” instructions shall
be included with the appliance or equipment installation
instructions; and
• The “special venting system” shall be Product Approved
by the Board, and the instructions for that system shall
include a parts list and detailed installation instructions.
A copy of all installation instructions for all Product Approved
side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or
all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 5
2
A
Quadra-Fire direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of the
building and all exhaust gases expelled to the outside. No
additional air source is required.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state
and national codes and regulations.
• Consult local building, fire officials or authorities having
jurisdiction about restrictions, installation inspection,
and permits.
When planning an installation, it is necessary to determine
the following information before installing:
Where the appliance is to be installed.
The vent system configuration to be used.
Gas supply piping.
Inspect appliance and components for
damage. Damaged parts may impair safe
operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
Carefully remove the appliance and components from
the packaging.
Remove cast door and glass door, and set aside on protective surface.
Remove log set and component pack from firebox.
Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
Electrical wiring.
fi
Whether optional accessories - devices such as a blower,
thermostat or remote control - are desired.
Keep appliance dry.
• Mold or rust may cause odors.
• Water may damage controls.
Before beginning the installation be sure that the following
tools and building supplies are available. Note: Not all
Reciprocating saw
Pliers
Hammer
Phillips Screwdriver
Flat Blade Screwdriver
Plumb Line
Level
Manometer
Tape Measure
Page 6
Hearth & Home Technologies disclaims any
responsibility for, and the
by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Variable Speed Drill/Driver
Wrench Set
Framing Square
Framing Material
Voltmeter
Gloves
Safety Glasses
Non-corrosive Leak Check Solution
or combustible gas detector
Caulking material (300ºF minimum
continuous exposure rating)
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
fi
3
Appliance Location and Clearances
NOTE:
· Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
· Illustrations/diagrams are not drawn to scale.
· Actual installation may vary due to individual design
preference.
Fire Risk
Provide adequate clearance:
• Around air openings
• To combustibles
• For service access
Locate appliance away from traffic areas.
When selecting a location for your appliance it is important to
consider the required clearances to walls (see
).
Fire Risk.
Locate and install appliance to all
clearance specifications in manual.
I
G - Alcove Height
E
B
A
C
A*
D
A*
F
H
E
Model
Columbia Bay FS
A
A*
B
C
D
E
F
G
H
I
Inches
6
6-3/4
2
6
14
2
84
19
36
36
Millimeters
152
171
515
152
356
51
2134
483
914
914
It is permissible to place the appliance on carpet.
CAUTION
Some carpet materials may be sensitive to radiant heat from the
appliance causing discoloration or odor.
NOTE: Flooring beneath appliance may reach 90 degrees
plus room ambient temperature. Check with flooring
manufacturer for maximum temperature allowed on flooring
surfaces.
Fire Risk.
Odor Risk.
Tipping Risk
• Install appliance on a stable, level platform/
floor strong enough to support appliance
without tipping.
•
USE wood flooring, ceramic tile, brick hearth
or high pressure laminate flooring applied
directly over the sub-flooring material.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 7
4
HORIZONTAL
OVERHANG
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles
as specified.
• Do not pack air space with insulation or
other materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
2 FT.
MIN.
(See
for specific clearances.)
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
20 in. and over
0 in. minimum
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
12
X
ROOF PITCH
IS X/ 12
Measure vertical clearances from this surface.
Measure horizontal clearances from this surface.
20 INCHES MIN.
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft
Flat to 6/12 ......................................................... 1.0*
Over 6/12 to .......................................................
7/12
. 1.25
Over 7/12 to 8/12 ............................................... 1.5*
Over 8/12 to 9/12 ............................................... 2.0*
Over 9/12 to 10/12 ............................................. 2.5*
Over 10/12 to 11/12 ........................................... 3.25
Over 11/12 to 12/12 ........................................... 4.0
Over 12/12 to 14/12 ........................................... 5.0
Over 14/12 to 16/12 ........................................... 6.0
Over 16/12 to 18/12 ........................................... 7.0
Over 18/12 to 20/12 ........................................... 7.5
Over 20/12 to 21/12 ........................................... 8.0
* 3 foot minimum in snow regions
Gas, Wood or Fuel Oil
Termination Cap
specifies minimum vent heights for various
pitched roofs.
B
A*
Gas
Termination
Cap **
*
**
Page 8
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
(SeeNote
Note2)
2)
(S
v
v
v
v
V = VENT TERMINAL
A
B
D*
X = AIR SUPPLY INLET
= 12 inches ............. clearances above grade, veran(See Note 1)
da, porch, deck or balcony
= 12 inches ............ clearances to window or door
that may be opened, or to permanently closed window. (Glass)
= 18 inches ............. vertical clearance to unventilated soffit or to ventilated soffit located above the terminal
*30 inches ............ for vinyl clad soffits and below
electrical service
F
= 9 inches .............. clearance to outside corner
G
= 6 inches ............... clearance to inside corner
H
= 3 ft. (Canada) ...... not to be installed above a gas
meter/regulatorassembly within 3
feet (90cm) horizontally from the
center-line of the regulator
I
J
= 3 ft. ....................... clearance to gas service regulator vent outlet
= 9 inches (U.S.A.)
12 inches (Canada)clearance to non-mechanical air
supply inlet to building or the
combustion air inlet to any other
appliance
= AREA WHERE TERMINAL IS NOT PERMITTED
K
= 3 ft. (U.S.A.)
6 ft. (Canada) ......... clearance to a mechanical
(powered) air supply inlet
L** = 7 ft. ......................... clearance above paved
(See Note 1)
sidewalk or a paved driveway
located on public property
M*** = 18 inches .............. clearance under veranda ,
porch, deck, balcony or overhang
42 inches .............. vinyl
S =
6 inches ................. clearance from sides of
(See Note 3)
electrical service
T = 12 inches ................ clearance above electrical
service
(See Note 3)
Alcove Applications
N
P
= 6 inches ................. non-vinyl sidewalls
12 inches ............... vinyl sidewalls
= 8 ft.
QMIN
RMAX
1 cap
3 feet
2 x Q ACTUA L _
___________________________________________________________________
2 caps
6 feet
1 x Q ACTUA L _
___________________________________________________________________
3 caps
9 feet
2/3 x Q ACTUA L _
___________________________________________________________________
4 caps
12 feet
QMIN = # termination caps x 3
** a vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings and
serves both dwellings.
*** only permitted if veranda, porch, deck or balcony is fully open on
a minimum of 2 sides beneath the floor, or meets Note 2.
1/2 x Q ACTUA L
RMAX = (2 / # termination caps) x QACTUAL
NOTE:
Local codes or regulations may require different
clearances.
NOTE: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
NOTE 1: On private property where termination is less than 7 feet above
a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed
cap is suggested. (See vents components pages.)
WARNING: In the U.S.: Vent system termination is NOT permitted
in screened porches. You must follow side wall, overhang and
ground clearances as slated in the instructions.
NOTE 2: Termination in an alcove space (spaces only open on one side
and without an overhang) are permitted with the dimensions specified for
vinyl or non-vinyl siding and soffits. 1. There must be at least 3 feet
minimum between termination caps. 2. All mechanical air intakes within
10 feet of a termination cap must be a minimum of 3 feet below the
termination cap. 3. All gravity air intakes within 3 feet of a termination cap
must be a minimum of 1 foot below the termination cap.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas with
two or more sides open. You must follow side wall, overhang and
ground clearances as stated in the instructions.
NOTE 3: Location of the vent termination must not interfere with access
to the electrical service.
Quadra-Fire assumes no responsibility for the improper performance of the appliance when the venting system does not meet
these requirements.
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH
VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED (part #VPK-DV).
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 9
5
In order to comply with applicable codes and product
warranties, use only following venting components:
Hearth & Home Technologies (HHT)
Security Chimney's Secure Vent Chimney System
Selkirk Metalbestos
AmeriVent
Simpson Dura-Vent (SDV)
ALL vent configuration specifications MUST be followed.
• This product is tested and listed to these
specifications.
• Appliance performance will suffer if specifications are
not followed.
Diagonal runs have both vertical and horizontal vent aspects
when calculating the effects. Use the rise for the vertical
aspect and the run for the horizontal aspect. (See
)
DO
NOT
USE
FIELD-FABRICATED
VENTING
COMPONENTS. Refer to the venting manufacturer’s
instructions.
Two 45° elbows may be used in place of one 90° elbow. On
45° runs, one foot of diagonal is equal to 8-1/2 in. (216mm)
horizontal run and 8-1/2 in. (216mm) vertical run. A length of
straight pipe is allowed between two elbows. (See
)
This product is approved to be vented either horizontally,
through the side wall or vertically through the roof. You may
vent through a Class A or masonry chimney if an approved
adapter is used.
This appliance is a direct vent heater. All combustion air must
come directly from the outside of the building. The vent pipe
for this unit consists of an inner and an outer pipe. The inner
pipe carries the appliance exhaust out of the system, and the
outer pipe brings fresh combustion air into the appliance.
A support box or ceiling firestop is required when the
venting passes through a ceiling.
•
Roof flashing and a storm collar are required when venting passes through the roof.
•
Follow instructions provided with the venting for installation of these items.
Fire Hazard.
Explosion Risk.
Asphyxiation Risk.
Do NOT connect this gas appliance to a chimney
flue serving a separate solid-fuel or gas burning
appliance.
in
•
12
A round support box/wall thimble or heat shield is
required when the venting passes through a combustible wall.
.
Vertical
•
8-1/2 in.
Horizontal
Vertical and horizontal measurements were made using the
following standards.
•
Pipe measurements are from center line to center line.
•
Horizontal terminations are measured to the outside of
the mounting surface (flange of termination cap). See
on page 8.
•
Vertical terminations are measured to the top of the last
pipe before termination cap.
•
Horizontal pipe installed level with 1/4 in. rise.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
May impair safe operation of this appliance or
other appliances connected to the flue.
Page 10
8-1/2 in.
•
•
•
•
•
CAUTION
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
1.
2.
3.
Measure the vertical distance from the center line of the
flue pipe to the center of the 90° elbow. On the graph
below, draw a horizontal line from that measurement
on the vertical axis across until it intersects with the
slanted line.
From the point of this intersection, draw a vertical line to
the bottom of the graph.
The point at which this line meets the bottom line of the
graph is the maximum length of the horizontal run.
EXAMPLE 1: If the vertical dimension from the center line
of the flue vent to the center of the 90° elbow is 7 ft. (2m),
the horizontal run to the outer wall flange must not exceed
13 ft. (4m).
NOTES
The maximum horizontal vent run is 15 ft. (5m) when the
vertical vent rise is 10 ft. (3m).
The minimum horizontal vent run is 11 in. (279mm).
Horizontal sections require a 1/4 in. (6mm) rise for every 12
ft. (305mm) of horizontal travel.
Exterior Vent Diameter = 6 5/8 in. (168mm); Inner Vent Diameter = 4 in. (101mm)
Horizontal sections require noncombustible support every 3
ft. (914mm), e.g. wall straps.
EXAMPLE 2: If the vertical dimension from the center line
of the flue vent is 21 ft. (6m), the horizontal run to the outer
wall flange must not exceed 9 ft. (3m).
A minimum 2 ft. (610mm) vertical rise is required before the
90 degree elbow.
4. Each 90° elbow is equivalent to 3 ft. (914mm) of vent
pipe and each 45° elbow is equivalent to 1 ft. (305mm)
of vent pipe, and must be subtracted from the vent pipe
run. A single horizontal to vertical 90° elbow is already
calculated into the allowable 15 ft. (5m) run. Each
additional 90° elbow reduces the maximum horizontal
distance by 3 ft. (914mm).
NOTE: If your installation falls within the gray-shaded area
on graph, see information on Vertical damper adjustment in
Section 8. (In the Commonwealth of Massachusetts, the word
damper shall be replaced with the words flue restrictor.)
EXAMPLE: The use of 3 elbows would reduce the allowable
horizontal run to 9 ft. (3 -1 = 2 elbows x 3 ft. = 6 ft.; 15 ft.
max. - 6 ft. = 9 ft. maximum).
35'
34'
32'
EX. 2
30'
28'
26'
24'
22'
20'
18'
VERTICAL DISTANCE
16'
FROM APPLIANCE TO
EX. 1
14'
12'
10'
8'
6'
4'
2'
0'
11" 2'
(MIN)
4'
6'
8'
10'
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
12'
14' 15'
(MAX)
Page 11
HHW2 - Recommended for
optimum performance.
90 DEGREE
ELBOW
PIPE LENGTH
PIPE
LENGTH
WALL WALL THIMBLE
THIMBLE
COVER
Fire Risk.
Explosion Risk.
Combustion Fume Risk.
Use vent run supports per installation instructions.
Connect vent sections per installation instructions.
• Maintain all clearances to combustibles.
• Do NOT allow vent to sag below connection
point to appliance.
Determine the desired location of the appliance. Check to
ensure that wall studs or roof rafters are not in the way when
the venting system is attached. If this is the case, you may
want to adjust the location of the appliance.
Fire Hazard.
Exhaust Fume Risk.
Impaired Performance of Appliance.
• Ensure vent components are locked together correctly.
• Pipe may separate if not properly joined.
• Maintain specified slope (if required).
Improper support may allow vent to sag or separate.
For installations using a round support box/wall thimble
(check pipe manufacturer's instructions), mark the wall for a
10 in. x 10 in. (254mm x 254mm) square hole. The center
of the square hole should line up with the center line of the
horizontal pipe, as shown in
on the next page.
Cut and frame the hole in the exterior wall where the vent will
be terminated. If the wall being penetrated is constructed of
noncombustible material, i.e. masonry block or concrete, a 7
in. (178mm) diameter hole is acceptable.
Direct vent pipe is designed with a locking connection. To
connect the venting system to the appliance flue outlet, a
twist-lock adapter is built into the appliance at the factory.
Remember to include wall thickness in minimum clearances
when figuring the measurements for your installation
needs.
Note: Direct vent pipe is designed to slide straight onto
the male ends of adjacent pipes and fittings by orienting the
pipe indentations so they match and slide into the entry slots
on the male ends, see
. Push the pipe sections
completely together, then twist-lock one section clockwise
approximately one-quarter turn, until the two sections are
fully locked. The female locking lugs may not be visible from
the outside, on the pipe or fittings. They may be located by
examining the inside of the female ends.
Page 12
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
WOOD
SCREW
CENTER OF
HOLE
CENTER
LINE
HOT
WALL
THIMBLE
CENTER
LINE
PART HHW2 PART
841-0670 (Preferred)
WALL THIMBLE
NOTES:
(1) The four wood screws provided should be replaced with
appropriate fasteners for stucco, brick, concrete, or
other types of sidings.
NOTE:
(1) Installation requires a minimum of 6 in. (152mm)
horizontal run of vent with a 1/4 in. (6mm) rise run towards
the termination. Each 1 ft. (305mm) of horizontal venting
must include a 1/4 in. (6mm) rise. Never allow the vent
to run downward. This could cause high temperatures
and may present the possibility of a house or structure
fire.
(2) The location of the horizontal termination cap on an
exterior wall must meet all local and national building
codes, and must not be easily blocked or obstructed,
see
on page 9.
(3) For installations requiring a vertical rise on the exterior
of the building, the HHT RHVK snorkel kit (Part #8448921) is available with a 14 in. (356mm) and a 36 in.
(914mm) tall snorkel termination cap. Follow the
same installation procedures as used for standard
horizontal terminations. If the snorkel termination must
be installed below grade (i.e. basement application),
proper drainage must be provided to prevent water from
entering the snorkel termination. Do not backfill around
snorkel termination.
Position the horizontal termination cap in the center of the 10
in. x 10 in. (254mm x 254mm) square hole and run a bead
of non-hardening mastic around its outside edges, so as to
make a seal between it and the wall, attach termination cap
to the exterior wall with the four wood screws provided. The
arrow on the vent cap should be pointing up (
)
(2) Termination cap HHW2 (Part #841-0670) is highly
recommended on a building with vinyl siding, as the
vinyl siding standoff is built in. The pilot hole will be 2 in.
(51mm) closer to the bottom of the square than the top.
Using a framing square, draw a 14 in. x 14 in. (356mm x
356mm) square around the pilot hole in the siding. See
.
8 in.
(203mm)
7 in.
(178mm)
7 in.
(178mm)
6 in.
(152mm)
(NOTE: If you are installing termination cap HHW2, the
pipe will be off center on the flashing). Ensure that proper
clearances to combustible materials are maintained. If
you are using an approved termination cap other than
HHW2 (part #841-0670) on a building with vinyl siding,
a vinyl siding standoff should be installed between the
vent cap and the exterior wall (
, on the next
page). Attach the vinyl siding standoff to the horizontal
vent termination. The vinyl siding standoff prevents
excessive heat from possibly melting the vinyl siding
material. Vent terminal shall not be recessed into a
wall or siding. Remove siding from the area where the
standoff will be located.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 13
VINYL SIDING
APPLY SEALANT
TO ALL FOUR
SIDES
SCREWS
BOLT HORIZONTAL
TOP TO VINYL
STANDOFF
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as specified.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials away from
vent pipe may cause fire.
SCREWS
WALL THIMBLE
COVER
WALL THIMBLE
VINYL SIDING
STANDOFF WITH
SIDING BENEATH
REMOVED
Place the wall thimble cover over the pipe assembly and
slide the appliance and vent assembly towards the wall,
carefully inserting the vent pipe into the vent cap assembly.
It is important that the vent pipe extend into the vent cap a
sufficient distance so as to result in a minimum pipe overlap
of 1-1/4 in. (32mm). Secure the connection between the vent
pipe and the vent termination cap by attaching the two sheet
metal strips extending from the vent cap assembly into the
outer wall of the vent pipe. Use the two sheet metal screws
provided to connect the strips to the pipe section (
).
Burn Risk.
Local codes may require installation of a cap
shield to prevent anything or anyone from
touching the hot cap.
Do NOT connect a pipe section to a termination cap without
using the telescoping flue section found on the termination
cap.
1/4 in. (6mm)
FOLD STRAP
HERE
SHEET METAL SCREW
WALL THIMBLE COVER/CEILING
FIRESTOP AS REQUIRED BY
LOCAL JURISDICTION
WALL
THIMBLE
STRAP
Note: The attachment from the vent pipe to the vent
termination cap must be sealed with silicone with a minimum
of 300ºF continuous exposure rating. Termination caps shall
not be recessed into a wall or siding.
Page 14
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
NOTE:
VERTICAL
TERMINATION
CAP
Maximum vertical rise allowable is 35 ft. (11m)
).
NOTE: Maximum number of 45° elbows permitted for a
vertical installation is eight, provided their installation does
not decrease maximum allowable horizontal run (as specified
by vent graph, on page 11).
STORM
COLLAR
FLASHING
FIRESTOP
SUPPORT
BOX
35 ft. (11m)
MAXIMUM
PIPE
LENGTH
NOTE: Maximum number of 90° elbows permitted for a
vertical installation is four, provided the termination falls
within the shaded area shown in vent graph on page 10. See
also
, within the four 90° elbows configuration,
the maximum allowable pipe length on the horizontal runs is
1 ft. (305mm) the minimum allowable pipe length on vertical
runs is 1 ft. (305mm).
Check the installation instructions for required 1 in. (25mm)
clearances (air space) to combustibles when passing
through ceilings, walls, roofs, enclosures, attic rafters, or
other nearby combustible surfaces. See page 16,
Check the instructions below for maximum vertical rise
of the venting system, and any maximum horizontal offset
limitations. All offsets must fall within the set parameters of
the vent graph (
) located on page 11.
ADDITIONAL RESTRICTION: This installation may not
have two horizontal sections connected by 90° elbows.
1'
2'
2'
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as specified.
• Do not pack air space with insulation or other
materials.
Failure to keep insulation or other materials away
from vent pipe may cause fire.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
1'
1'
Page 15
Set the gas appliance in its desired location. Drop a plumb
bob down from the ceiling to the position of the appliance
flue exit, and mark the location where the vent will penetrate
the ceiling. Drill a small hole at this point. Next, drop a plumb
bob from the roof to the hole previously drilled in the ceiling,
and mark the spot where the vent will penetrate the roof.
Determine if ceiling joists, roof rafters, or other framing will
obstruct the venting system. You may wish to relocate the
appliance, or to offset, as shown in
to avoid
cutting load bearing members. When location is determined,
drill small hole.
Assemble the desired lengths of pipe and elbows necessary
to reach from the appliance up through the round support
box. Ensure that all pipe and elbow connections are in their
fully twist-locked position. Assemble as instructed.
Cut a hole in the roof centered on the small drill hole placed in
the roof in Step 2. The hole should be of sufficient size to meet
the minimum requirements for clearance to combustibles, as
specified. Continue to assemble lengths of pipe and elbows
necessary to reach from the ceiling support box/wall thimble
up through the roof line. Galvanized pipe and elbows may
be utilized in the attic, as well as above the roofline. The
galvanized finish is desirable above the roofline, due to its
higher corrosion resistance.
NOTE:
(1) If an offset is necessary in the attic to avoid obstructions,
it is important to support the vent pipe every 3 ft. (914mm)
to avoid excessive stress on the elbows, and possible
separation. Wall straps are available for this purpose
.
PLUMBER'S TAPE
CONNECTED TO
WALL STRAP
WALL
STRAP
TWO 45 DEGREE
ELBOWS
(2) Whenever possible, use 45° elbows, instead of 90°
elbows. The 45° elbow offers less restriction to the flow
of flue gases and intake air.
Slip the flashing over the pipe section(s) protruding through
the roof. Secure the base of the flashing to the roof with
roofing nails. Ensure the roofing material overlaps the top
edge of the flashing as shown in
. Verify that the
chimney is the required height above the roof (see roof pitch
table,
on page 8).
To install the round support box/wall thimble cover in a flat
ceiling, cut a 10 in. (254mm) square hole in the ceiling,
centered on the hole drilled in Step 2. Frame the hole as
shown in
.
SHINGLES OVERLAP ON
TOP EDGE OF FLASHING
CEILING JOISTS
FRAMING
ROUND CEILING
SUPPORT BOX/WALL
THIMBLE COVER
1-1/2 in. (38mm) LONG
WOOD SCREWS
Page 16
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Continue to assemble pipe sections until the height of the
vent (before adding the termination cap) meets the minimum
code requirements as outlined in the current CAN/CGA-B149
Installation Codes (in Canada), the National Fuel Gas Code
NFPA 54/ANSI Z223.1 (in USA), or local codes. Note that
for steep roof pitches, the vent height must be increased.
See Roof Pitch Table (
, on page 8). In high wind
conditions, nearby trees adjoining rooflines, steep pitched
roofs, and other similar factors can result in poor draft, or
down drafting. In these cases increasing the vent height or
switching to the high wind termination cap may solve this
problem.
NAILS
CEILING FIRESTOP
CLEARANCE
CLEARANCE
CLEARANCE
Slip the storm collar over the pipe, and push it down to the
top of the flashing (
). Use non-hardening sealant
above and below the joint between the storm collar and the
pipe.
CLEARANCE
OPTIONAL HIGH WIND
TERMINATION CAP
SECURE FLASHING WITH
NON-HARDENING SEALANT
AND ROOFING NAILS
Fire Risk.
Explosion Risk.
• Any occupied areas above the first floor, including
closets and storage spaces, which the vertical
vent passed through must be enclosed. The
enclosure may be framed and sheetrocked with
standard construction materials; however, refer
to these installation instructions for the minimum
allowable clearance between the outside of the
vent pipe and the combustible surfaces of the
enclosure. Do not fill any of the required air space
with insulation.
Twist-lock the vent cap and seal.
Note: For multi-story vertical installations, a ceiling firestop
is required at the second floor, and any subsequent floors
(
). The opening should be framed to 10 in. x
10 in. (254mm x 254mm) inside dimensions, in the same
manner as shown in
, on page 16.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 17
Follow installation Steps 1 and 2 under vertical installation
section, pages 15-16.
Remove shingles or other roof covering as necessary to cut
the rectangular hole for the support box. Cut the hole 1/8 in.
(3mm) larger than the support box outline.
Lower the support box through the hole in the roof until the
bottom of the support box protrudes at least 2 in. (51mm)
below the ceiling (
). Align the support box both
vertically and horizontally with a level. Temporarily tack the
support box in place through the inside walls and into the
roof sheathing.
LEVEL
CATHEDRAL CEILING
SUPPORT BOX
CUT HOLE 1/8 in.
(3mm) GREATER IN
SIZE THAN PATTERN
OF SUPPORT BOX AS
IT IS PROJECTED
ONTO ROOF LINE
2 in. (51mm)
MIN. BELOW
FINISHED
CEILING
Place the support clamp (provided with the support box)
inside the support box (at the bottom), and secure to the pipe
section. The clamp allows the support box to support the
weight of the pipe sections. Continue to add pipe sections
until you are above the roofline.
Complete the cathedral ceiling installation by following the
same procedures outlined in steps 7 through 9 for vertical
installations, page 17.
Install the black trim collar around the outside of the cathedral
ceiling support box (
). The two pieces of the trim
collar slide over one another to allow for easy adjustment
around the support box. Using the six screws provided,
secure the four corners and the overlapping sections of the
trim collar to the ceiling. You may want to predrill the holes for
the overlapped sections for ease of installation.
Using tin snips, cut the support box from the top corners
down to the roofline, and fold the resulting flaps over the
roof sheathing (
). Before nailing it to the roof,
run a bead of non-hardening mastic around the top edges
of the support box to make a seal between it and the roof.
Clean out any combustible material from inside the support
box.
Assemble the desired lengths of pipe and elbows necessary
to reach from the appliance up through the round support
box. Ensure that all pipe and elbow connections are in their
fully twist-locked position. Assemble as instructed.
Page 18
TRIM COLLAR
CATHEDRAL
CEILING
SUPPORT
BOX
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
SCREWS
TERMINATION
CAP
TOP
ADAPTOR
FLASHING
EXISTING
METAL CHIMNEY
SYSTEM
Pass the flex pipe down through the center of the chimney
system, and center the top adapter on the top of the chimney
pipe. Drill four 1/8 in. (3mm) diameter holes through the
top adapter, and into the chimney top. Ensure that you are
drilling into the metal on the chimney. Twist lock the high
wind termination cap onto the top adapter
.
4 in. (102mm)
FLEX PIPE
RETRO
CONNECTOR
DIRECT
VENT PIPE
CAUTION
TERMINATION
CAP
Ensure that existing chimney is functionally sound and clean.
• Have inspection done by qualified chimney sweep or
professional installer BEFORE converting to direct vent
appliance.
SHEET METAL
Remove existing chimney cap.
Measure the distance from the top of the chimney to the
bottom of the ceiling support box, add 3 in. (76mm) to this
measurement, and cut a section of 4 in. (101mm) flex pipe
to that length (the flex should be fully extended).
Connect the end of the flex pipe section to the underside
of the top adapter, using four sheet metal screws
.
Top Adapter
Pipe
HOLES
Pull the flex pipe down through the ceiling support box, until
it protrudes approximately 3 in. (76mm). Connect the flex
pipe to the retro connector, and attach with sheet metal
screws.
Push the flex pipe back up into the ceiling support box,
center the retro connector, and attach it to the support box
with sheet metal screws.
The connection between the appliance and the retro
connector may be completed with sections of direct vent
pipe.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 19
TERMINATION
CAP
TOP ADAPTOR
MASONRY
CHIMNEY
RETRO CONNECTOR
FLASHING
FOUR MASONRY BOLTS
RETRO CONNECTOR
COVER
4 in. (102mm)
FLEX LINER
90 DEGREE
ELBOW
Secure the flashing to the top of the masonry chimney using
a bead of non-hardening sealant-adhesive. If the flashing is
larger than the top of the chimney, cut and fold flashing as
needed to fit chimney
.
DIRECT VENT PIPE
CUT AND BEND FLASHING AS
NEEDED TO FIT CHIMNEY
CAUTION
Ensure that existing chimney is functionally sound and clean.
• Have inspection done by qualified chimney sweep or
professional installer BEFORE converting to direct vent
appliance.
Before cutting any holes, assemble the desired sections
of direct vent pipe to determine the center of the masonry
penetration.
Once the center point of the penetration has been determined,
cut a 6 in. (152mm) diameter hole in the masonry. If the hole
is too large, the retro connector might not mount properly; if
the hole is too small, the appliance might starve for intake
air. If there is a frame wall in front of the masonry wall, cut
and frame a 10 in. (254mm) square opening in the wall
(centered around the 6 in. (152mm) masonry opening). If
there is sheet rock only (no studs) in front of the masonry the
10 in. (254mm) opening is still needed, but does not need
to be framed. If the hole is framed a wall thimble is required.
This allows the retro connector to mount directly on the
masonry and provide the correct clearances to combustibles
Page 20
SEALANT-ADHESIVE
To determine the length of flex needed, measure from 3 in.
(76mm) above the top of the flashing down to the level of the
opening. Add the distance from the center of the chimney
out through the wall. Cut a piece of 4 in. (102mm) flex to this
length (extended to its nominal length). Be sure to leave 2-3
in. (51-76mm) of flex above the existing chimney to allow for
connection to the termination kit.
Connect the flex liner to the top adapter using three sheet
metal screws (
, page 19).
Feed the flex liner through the flashing into the chimney.
Carefully feed the flex liner down the chimney to the bottom
and out the opening in the masonry wall, forming an angle to
line up the flex liner with the vent opening on the appliance.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Fire Risk.
Explosion Risk.
• Do not let the flex liner sag below the level at
which it will connect to the appliance or connector.
This could allow hot gas to become trapped and
potentially become a fire hazard. The flex liner path
should always be sloped up toward the termination
cap.
If additional lengths of flex liner are needed to span the
chimney height, use a flex coupler to connect the pieces of
flex liner together. Connect the flex to the coupler by using
four sheet metal screws for each side (
).
Attach the flex to the retro connector. Use three sheet metal
screws to attach the flex liner to the connector (
). Mount the retro connector to the masonry wall using
masonry bolts. Redrill larger holes on connector as needed.
Be careful to ensure that the connector is centered in the
opening and the mounting holes line up with the masonry
wall.
6 in. (152mm)
DIAMETER
OPENING IN
MASONRY
WALL
FLEX LINER
RETRO CONNECTOR
THREE MASONRY BOLTS
(NOT INCLUDED)
FLEX COUPLER
SHEET METAL
SCREWS
Secure the top adapter to the flashing. Use three sheet
metal screws through the side of the top adapter into the
flange on the flashing (
). Twist lock the high
wind termination cap on to the top adapter.
Slide the wall thimble cover over retro connector and secure
with masonry bolts (
). If you have a framed wall
in front of the masonry, use wood screws to mount wall
thimble cover to framed wall, over retro connector and 10
in. (254mm) square framed opening (
, page
20). If needed, add a section of direct vent pipe to the retro
connector in order to extend through the opening in the wall
thimble cover.
HIGH WIND
TERMINATION CAP
TOP ADAPTOR
THREE SHEET
METAL SCREWS
FLASHING
RETRO CONNECTOR
WALL THIMBLE COVER
FOUR MASONRY BOLTS
(NOT INCLUDED)
The connection between the appliance and the retro
connector may be completed with sections of direct vent
pipe.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 21
6
Before making gas connections ensure that the appliance
being installed is compatible with the available gas type.
Any natural or propane gas conversions necessary to meet
the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified
and approved parts.
Lift the burner from the left side and slide left until
free from the orifice receiver. Remove from the firebox and
handle with care.
KIT CONTENTS:
fi
TOOLS REQUIRED: Power drill (a 90° handle is helpful); #2
Phillips bit; 5/32 in. Allen wrench; 5/8 in. open-end wrench.
Disconnect power and turn off gas supply if installed.
Remove the front, glass, brick refractory and logs if installed.
(It is only necessary to remove the left brick panel for burner
removal. The metal brick refractory does not need to be
removed.)
Opens Left
Closes Right
Loosen the shutter adjustment nut (located underneath the appliance) with a 7/16 in. wrench.
It is helpful to remove the nut completely. Slide the shutter to
the right (closed position).
Page 22
With a 5/8 in. wrench remove orifice retaining nut.
Replace with appropriate orifice.
PROPANE
.0635 (52 DMS)
NATURAL GAS
.1065 (36 DMS)
If the shutter is removed with the burner as indicated in
, it must be reinstalled over the orifice prior to the
reinstallation of the burner.
Remove the pilot hood, and set aside. Using a 5/32
in. allen wrench, remove the pilot injector and replace with an
appropriate injector (35 LP, 62 NG).
Reinstall the burner, and reassemble the appliance.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
E
Fire Risk.
Explosion Risk.
Disconnect any electrical cords and
turn off gas supply to unit before
proceeding if converting fuel on an
appliance already fully installed.
Remove upper and lower back shield. Loosen the set collars on the extension rods with the 3/32 in. Allen wrench.
Remove the rods and adapter cap.
D
F
Ensure that the rubber gasket
is properly positioned and install the new HI/LO pressure regulator assembly to the valve using the new screws
supplied with the
kit. Tighten screws securely. (Reference torque = 25 in./lb.)
Install the enclosed identification label
to the valve body
where it can be seen.
A
B
C
Fill out the conversion label and attach it to the valve cover.
Turn control knob to the OFF position, ensure that
gas supply to the valve has been turned off. Using a Torx
TH20, or slotted screwdriver, remove the three pressure regulator mounting screws
, pressure regulator tower
,
and diaphragm
.
Fire Risk.
Explosion Risk.
Gas Leak Risk.
• Rubber gasket must be seated properly on valve
face.
• Do no install a valve or regulator that has been
dropped.
Fire Risk.
Explosion Risk.
If the information in these instructions is
not followed exactly, a fire, explosion or
production of carbon monoxide may result
causing property damage, personal injury
or loss of life.
The qualified service agency is responsible
for the proper installation of this conversion
kit. The installation is not proper and
complete until the operation of the converted
appliance is checked as specified in the
manufacturer’s instructions supplied with
the kit.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 23
Proper input pressures required for optimum appliance performance, gas line sizing requirements need to be followed
from NFPA54.
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Verify inlet pressures.
• High pressure may cause overfire
condition.
• Low pressure may cause explosion.
Install regulator upstream of valve if line pressure
is greater than 1/2 psig.
Pressure requirements for appliance are shown in the table
below.
PRESSURE
NG
LP
Minimum Inlet Pressure
4.5 inches w.c.
11.0 inches w.c.
Maximum Inlet Pressure
7.0 inches w.c.
14.0 inches w.c.
Manifold Pressure on “HI”
3.5 inches w.c.
10.0 inches w.c.
If the pressure is not sufficient, ensure:
1) the piping used is large enough.
2) the supply regulator is adequately adjusted.
3) that the total gas load for the residence does not exceed
the amount supplied.
The supply regulator (the regulator that attaches directly to the
residence inlet or to the propane tank) should supply gas at
the suggested input pressure listed above. Contact the local
gas supplier if the regulator is at an improper pressure.
Page 24
NOTE: Have the gas supply line installed in accordance with
local building codes, if any. If not, follow ANSI Z223.1. Installation should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth of
Massachusetts, installation must be performed by a licensed
plumber or gas fitter.)
NOTE: A listed (and Commonwealth of Massachusetts
approved) 1/2 inch (13mm) T-handle manual shut-off valve and
flexible gas connector are connected to the 1/2 inch (13mm)
control valve inlet.
Gas Leak Risk.
• Support control when attaching pipe to
prevent bending gas line.
NOTE: The gap between the supply piping and gas access
hole may be plugged with non-combustible insulation to prevent
cold air infiltration.
Leak test all gas line joints and the gas control valve prior
to and after starting the fireplace.
Before making the gas connection, ensure that the appliance
you are installing is designed for the type of gas being
supplied. This information can be found on the Ratings Label
under the appliance. If the appliance has been converted to
propane (LP), the valve cover should have a label stating
that the unit has been converted to propane.
Connect the gas line at the 3/8 in. (9.5mm) pipe connector
on the valve at the back of appliance. We recommend
connecting the appliance with an approved flex gas line.
If flex gas lines are not approved in your area, you must
connect a hard pipe to the gas hookup.
You must supply a manual shut-off valve in a visible location
within 3 feet (914mm) of the appliance.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Fire or Explosion Hazard
• Gas build-up during line purge may ignite.
• Purge should be performed by qualified technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as
sparks or open flame.
A small amount of air will be in the gas supply lines. When
first lighting appliance it will take a short time for air to
purge from lines. When purging is complete the appliance
will light and operate normally.
Air only needs to be purged again if gas valve has been
turned to the OFF position.
Omni-Test Laboratories listed gas appliances are tested
and approved without requiring changes for elevations
from 0 to 2000 feet in the U.S.A. and 0 to 4500 feet in
Canada.
When installing this appliance at an elevation above 2000
feet, it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Input
rate should be reduced by 4% for each 1000 feet above a
2000 foot elevation in the U.S.A. If the heating value of the
gas has been reduced, these rules do not apply. To identify
the proper orifice size, check with the local gas utility.
If installing this appliance at an elevation above 4500 feet
(in Canada), check with local authorities.
CHECK FOR GAS LEAKS
Explosion Risk
Fire Risk
Asphyxiation Risk
• Check all fittings and connections.
• Do not use open flame.
• After the gas line installation is complete, all
connections must be tightened and checked
for leaks with a commercially-available,
non-corrosive leak check solution. Be sure
to rinse off all leak check solution following
testing.
Fittings and connections may have loosened
during shipping and handling.
Fire hazard.
Do NOT change the valve settings.
• This valve has been preset at the factory.
• Changing valve settings may result in fire
hazard or bodily injury.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 25
7
See B5 below for recommended maximum lead length (two
wire) when using wall thermostat/switch.
NOTE: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the
8.
Ensure the thermostat is mounted level for accurate
readings.
9.
The thermostat should be mounted on an inside wall
and not in direct line with the appliance convection air.
10. If the thermostat is located too close to the appliance,
you may need to set the temperature setting slightly
higher to maintain the desired temperature in your
home.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
Wire 110v to electrical junction box.
Do NOT wire 110v to the valve.
Do NOT wire 110V to wall switch.
• Incorrect wiring will damage millivolt
systems.
1.
This appliance may be used with a wall switch, wall
mounted thermostat and / or a remote control.
2.
If using thermostat, use one compatible with a millivolt
gas valve system.
3.
Follow parameters for locating thermostat (see individual thermostat instructions) to ensure proper operation
of appliance.
4.
Use low resistance thermostat wire for wiring from ignition system to the wall switch and thermostat.
5.
Use the following chart for wire sizing.
16 gauge
65 feet
18 gauge
40 feet
20 gauge
25 feet
22 gauge
18 feet
6.
Keep wire lengths as short as possible by removing
any excess wire length.
7.
Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
Page 26
Shock hazard.
• This appliance is equipped with a three
pronged (grounding) plug for your protection
against shock hazard and should be plugged
directly into a properly grounded three prong
receptacle. Do not cut or remove the grounding
prong from this plug.
This appliance DOES NOT require 110 VAC supply for
operation. A wiring diagram is shown in
on the
next page.
This appliance is equipped with a millivolt control valve.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
THERMOPILE
GAS PILOT IGNITOR
THERMOCOUPLE
IGNITOR
Red 28 in.
(711MM)
ON/OFF
SWITCH
Red 28 in.
(711MM)
CAUTION
VALVE
CAUTION
Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
Verify proper operation after servicing.
Shock hazard.
• Replace damaged wire with type 105O C
rated wire.
• Wire must have high temperature insulation.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 27
8
Appliance Setup
Remove shipping materials from inside or underneath the
firebox.
Install approved accessories per instructions included with
accessories. Refer to Section 12 for appropriate accessories.
Shock or fire risk.
Use ONLY optional accessories approved for
this appliance.
• Using non-listed accessories voids
warranty.
• Using non-listed accessories may result in a
safety hazard.
• Only Hearth & Home Technologies approved
accessories may be used safely.
Set the replacement gold crown in place, reinsert
screws and tighten.
IMPORTANT! PREVENT PERMANENT STAINING!
Use a soft cloth and a window cleaning solution to clean
all fingerprint oils from the gold or nickel surface of crown
PRIOR to lighting the appliance.
TOOLS REQUIRED: Phillips head screwdriver.
REMOVAL OF METAL REFRACTORY BRICK
2 Screws
2 Screws
Remove the door from the appliance. Remove
the existing black crown by removing the four screws on the
back side of the face, and pull the crown off the door.
Page 28
To remove existing metal refractory remove the
two screws located on the left and the two on the right sides
behind the side curtains.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
While still breakable, the logs do not become fragile until
after the appliance is burned and they have cured. After
curing, any handling must be done with care as breakage
can easily occur.
Holding both sides of the metal refractory brick
piece, pull slightly together and rotate out of the firebox.
1
4
2
3
Install rear panel, gently wedging it between support shelf and baffle base. Install the brick brackets that are
enclosed with the brick set.
1
Rear Log
1
1
Left Front Log
2
1
Right Front Log
3
1
Twig
4
Locater Pin.
Install the left and right brick panels. Use the screw
placement shown in
to secure them in place.
Reassemble appliance.
Insert locator pin in rear log. Insert rear log onto
log pan over stud.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 29
that gas can contact them on all sides. Avoid stacking the
embers on top of each other.
NOTE: Do not block gas ports.
Remove the grille: Slide the grille out of the slots in the existing door.
Place right and left front logs on burner in the grooves
provided on the burner surface.
Remove the existing door from the appliance.
Remove the crown from the existing door by removing four
screws on the back side of the door assembly. Pull crown
off door face.
Install replacement door with glass onto appliance.
Reinstall the crown.
Reinstall the grille onto the new door assembly.
Place twig over the locator pin on the rear log,
gently laying the log across the two front logs. To complete
your log set application reinstall the front of the unit.
CAUTION
Handle glass assembly with care.
• Inspect the gasket to ensure it is undamaged.
• Inspect the glass for cracks, chips or
scratches.
• Do NOT strike, slam or scratch glass.
• Do NOT operate appliance with glass door
removed, cracked, broken or scratched.
• Replace glass assembly as a complete
assembly.
Explosion Risk.
• Follow ember placement instructions in
manual.
• Do NOT place embers directly over
burner ports.
• Replace ember material annually.
Improperly placed embers interferes with proper burner
operation.
Place individual pieces of embers in front of and
around the gas log where they can be seen. Space them so
Page 30
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Turn off power supply.
INCLUDED IN KIT: Blower; 2 female spade wire connectors.
Remove blower housing from appliance, if necessary.
TOOLS REQUIRED: Phillips head screwdriver.
Disassemble housing if needed, retaining all fasteners, and
remove the blower.
Reassemble blower in housing using fasteners previously
removed.
Reinstall blower housing to appliance.
Turn power supply back on.
Snap Disk
F
F
Fan Speed
Control
WHITE
WHITE
BLACK
BLACK
BLACK
F M
Ground
BLACK
M F
BLACK
BLACK
GRN
WHITE
F
M
F = Female
M = Male
Power Cord (110 VAC)
Strain Relief Bushing
Fan Assembly
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 31
Refer to the vent graph on page 11. If your installation falls
within the range of the gray shaded area of graph, it may be
necessary to make an adjustment to the vertical damper to
improve the flame appearance in your appliance.
OPEN
CLOSE
The shutter is located on the underside of the
appliance, on the right side. To adjust the shutter, loosen
the wingnut.. Retighten the wingnut after adjustment.
The vertical damper adjustment is located on the
right side of the unit behind the side curtain. The damper is
centered towards the top of the unit.
Loosen screws using a Phillips screwdriver.
Pivot the vertical damper adjustor in 1/4 in. increments while
observing the flame activity.
Moving the shutter bolt to the right closes the shutter. Moving
the shutter bolt to the left, will open the shutter. Opening the
shutter causes flames to become shorter and blue. Closing
the shutter creates taller orange/yellow flames.
NOTE: Do not close so much as to cause a sooty flame.
Improper adjustment can cause sooting in the firebox and/or
on the outside of a house with a horizontal termination.
After adjustment, tighten nut to lock in place.
Turn clockwise to open the damper = less flame height and
more blue in flame color.
Turn counterclockwise to close damper = increased flame
height and more yellow in flame color.
Make adjustment until flame size and activity suits your
personal preference, and then retighten screws on
adjustment control.
NOTE: In the Commonwealth of Massachusetts, the word
damper shall be replaced with the words flue restrictor.
Page 32
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
9
Read this entire manual prior to using the appliance. Failure
to follow the instructions may result in property damage,
bodily injury, or even death.
Remove all shipping materials from inside and/or
underneath the firebox.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to
the owner’s information manual provided with this appliance.
For assistance or additional information consult a qualified
installer, service agency or the gas supplier.
Review proper placement of logs, mineral wool.
Check the wiring.
Check the baffle adjustment.
Ensure that there are no gas leaks.
Ensure that the glass is sealed and in the proper position.
Ensure that the flow of combustion and ventilation air
is not obstructed (front grilles and vent caps).
Glass door must be in place when appliance is
operating.
Risk of:
• Combustion Fumes
• Fire
•
•
•
•
Do NOT operate appliance with glass door
removed.
Open viewing glass for servicing only.
Glass door MUST be in place and sealed before
operating appliance.
Only use glass door certified for use with appliance.
Glass replacement should be done by qualified
technician.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
FAN SPEED: This knob controls the speed of the blower
that pushes the heated air into the room.
MAIN BURNER: This control is used to turn the appliance
on and off.
PILOT IGNITOR: The pilot ignitor is used only to start
the pilot. When the valve control knob is turned to the
pilot position and fully depressed press the piezo ignitor
repeatedly creating a blue spark directly next to the pilot,
igniting the pilot flame.
VALVE CONTROL: This knob is used to control gas to
the appliance and for starting the pilot. There are three
positions,
. The indicator on the valve
indicates the position of the knob.
COMFORT CONTROL: This knob controls the flame height
from low (“LO”) to high (“HI”).
NOTE: If using a remote control wall switch, or thermostat,
the On/Off Switch must be left “OFF”. Turning the On/Off
Switch to “ON” will keep the appliance on continually.
fl
• Keep clothing, furniture, draperies and other flammable
materials away.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 33
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life
A. This appliance has a pilot that must be lit manually. When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING, smell around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
* Do not try to light any appliance.
* Do not touch any electric switch, do not use any phone in your building.
* Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
* If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't
try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance
and to replace any part of the control system and any gas control which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. Set the thermostat to the lowest setting (if applicable) and turn off
the switch at the control panel.
3. Disconnect the power from the appliance.
4. Open the door of the appliance. May need to remove face/front first.
5. Push in gas control knob slightly and turn clockwise
to the "OFF"
position. Do not force.
6. Wait five (5) minutes to clear out any gas. Smell for gas, including near the floor. If you smell gas, STOP! Follow "B" of the
safety information above. If you don't smell gas go to the next step.
7. Push gas control knob in and turn counterclockwise
to the pilot position. NOTE: Knob cannot be turned unless knob is
pushed in slightly. Do not force.
8. PIEZO IGNITER: Press down on the gas control knob in pilot position and simultaneously press the piezo igniter.
(This may take many repetitions for lighting.)
ELECTRONIC IGNITER: If the unit is equipped with an electronic igniter it should begin sparking right away.
9. The pilot should be visible through the door opening.
10. After the pilot is lit, continue holding control knob down for approximately
PILOT HOOD
30 seconds. Release the knob and it will pop back up. Pilot should remain lit. MILLIVOLT
THERMOCOUPLE
GENERATOR
If it goes out, repeat steps 7 through 9.
* If the knob does not pop up when released, stop and immediately call your
service technician or gas supplier.
* If the pilot will not stay lit after several tries, turn the gas control knob
clockwise
to "OFF" and call your service technician or gas supplier.
11. Reinstall door and face. Wait five minutes to allow pilot flame to stabilize and
establish proper draft.
12. Push down and turn gas control knob counterclockwise
to "ON".
13. Push burner rocker switch on the control panel to "ON". If thermostat is to be used, leave switch in "OFF" position and set the
thermostat to desired setting.
14. Reconnect electrical power to appliance.
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to lowest setting.
2. Turn off all electric power to the appliance if service is to be performed.
3. Push in gas control knob slightly and turn clockwise
to "OFF" position.
Page 34
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
CAUTION
When you light your appliance, you may notice that it produces heat which does have an associated odor or smell. If
you feel this odor is excessive it may require the initial three
to four hour continuous burn on high followed by a second
burn up to 12 hours to fully drive off any odor from paint and
lubricants used in the manufacturing process. Condensation
on the glass is normal.
NOTE: The appliance should be run three to four hours
on the initial start-up. Turn it off and let it cool completely.
Remove and clean the glass. Replace the glass and run the
appliance for an additional 12 hours. This will help to cure
the products used in the paint and logs.
During this break-in period it is recommended that some
windows in the house be opened for air circulation. This will
help avoid setting off smoke detectors, and help eliminate
any odors associated with the appliance’s initial burning.
Fire Risk.
High Temperatures.
• Prevent accidental appliance operation when not
attended.
• Unplug or remove batteries from remote control if absent
or if appliance will not be used for an extended period of
time.
• Property damage possible from elevated temperatures.
CAUTION
Smoke and odors released during initial operation.
• Open windows for air circulation.
• Leave room during initial operation.
• Smoke may set off smoke detectors.
Smoke and odors may be irritating to sensitive individuals.
Fire Hazard.
Keep combustible materials, gasoline
and other flammable vapors and liquids
clear of appliance.
• Do NOT store flammable materials in the appliance’s
vicinity.
• Do NOT use gasoline, lantern fuel, kerosene, charcoal
lighter fluid or similar liquids in this appliance.
• Combustible materials may ignite.
Keep combustible household items away from appliance.
Do NOT obstruct combustion and ventilation air.
• Do NOT place combustible items on top of or in front of
appliance.
• Keep furniture, draperies away from appliance.
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the appliance warms,
this condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance
is allowed to burn for 20 to 40 minutes.
Odor from appliance
When first operated, this appliance may release an odor for the first several hours.
This is caused by the curing of the paint and the burning off of any oils remaining from
manufacturing. If appliance has not been used for some time, dust can build up and
cause an odor.
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be
cleaned within 3 to 4 hours of initial burning to remove deposits left by oils from the
manufacturing process. A non-abrasive cleaner such as gas appliance cleaner may be
necessary. See your dealer.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down,
similar to the sound produced by a furnace or heating duct. This noise does not affect
the operation or longevity of the appliance.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 35
10
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the
corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician.
1. After repeated triggering of the piezo
button, the spark ignitor
will not light the pilot.
2. The pilot will not stay
lit after carefully following the lighting instructions.
a. Defective ignitor.
Check the spark at the electrode and pilot. If no spark and electrode
wire is properly connected, replace the ignitor.
b. Defective pilot or
misaligned electrode
(spark at electrode).
Using a match, light the pilot. If the pilot lights, turn off the pilot and
trigger the piezo button again. If the pilot lights, an improper gas/air
mixture caused the bad lighting and a longer purge period is recommended. If the pilot will not light, ensure the gap at the electrode and
pilot is one-eighth (1/8) inch to have a strong spark. If the gas is OK,
replace the pilot.
c. No gas or low gas
pressure.
Check the remote shut-off valve from the appliance. Usually, there is
a valve near the gas main. There can be more that one (1) valve from
the appliance and the main.
d. No LP in tank.
Check the LP (propane) tank. You may be out of fuel.
a. Defective thermocouple.
Check that the pilot flame impinges on the thermocouple. Clean and /or
adjust the pilot for maximum flame impingement.
Ensure that the thermocouple connection at the gas valve is fully
inserted and tight (hand tighten plus 1/4 turn).
Disconnect the thermocouple from the valve, place one millivolt lead
wire on the tip of the thermocouple and the other meter wire on the
thermocouple copper lead. Start the pilot and hold the valve knob in. If
the millivolt reading is less than 15mV, replace the thermocouple.
b. Defective valve.
3. The pilot is burning,
a. ON/OFF switch or
there is no gas to the
wires defective.
burner, the valve knob is
in the ON position, and
the ON/OFF switch is in
the ON position.
b. Thermopile may
not be generating
sufficient millivoltage.
If the thermocouple is producing more than 15 millivolts, replace faulty
valve.
Check the ON/OFF switch and wires for proper connections. Place the
jumper wires across the terminals at the switch. If the burner comes on,
replace the defective switch. If the switch is OK, place the jumper wires
across the switch wires at the gas valve. IF the burner comes on, the
wires are faulty or connections are bad.
If the pilot flame is not close enough physically to the thermopile, adjust
the pilot flame.
Be sure the wire connections from the thermopile at the gas valve terminals are tight and that the thermopile is fully inserted into the pilot
bracket.
Check the thermopile with a millivolt meter. Take the reading at TH-TP
& TP terminals of the gas valve. The meter should read 325 millivolts
minimum, while holding the valve knob depressed in the pilot position,
with the pilot lit, and the ON/OFF switch in the OFF position. Replace
the faulty thermopile if the reading is below the specified minimum.
With the pilot in the ON position, disconnect the thermopile leads from
the valve. Take a reading at the thermopile leads. The reading should
be 325 millivolts minimum. Replace the thermopile if the reading is
below the minimum.
Page 36
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
3. (Continued)
c. Defective valve.
Turn the valve knob to the ON position. Place the ON/OFF switch in the
ON position. Check the millivolt meter at the thermopile terminals. The
millivolt meter should read greater than 125mV. If the reading is acceptable, and if the burner does not come on, replace the gas valve.
d. Plugged burner
orifice.
Check the burner orifice for stoppage. Remove stoppage.
e. Wall switch or
wires are defective.
Follow the corrective action in Symptom and Possible Cause 1.a.
Check the switch and wiring. Replace where defective.
4. Frequent pilot outage a. Pilot flame may
Clean and adjust the pilot flame for maximum flame impingement on
problem.
be too high or too
thermocouple. Follow lighting instructions carefully.
low, or blowing
(high), causing safety
pilot to drop out.
5. The pilot and main
burner extinguish while
in operation.
a. No LP in tank.
Check the LP (propane) tank. Refill the fuel tank.
b. Inner vent pipe
leaking exhaust
gases back into the
system.
Check for proper vent connection at flue collar and all vent joints.
c. Horizontal vent
improperly pitched.
The horizontal vent cap should slope down only enough to prevent any
water from entering the appliance.
d. Bad thermopile or
thermocouple.
Replace if necessary.
e. Improper vent cap Check for proper installation and freedom from debris or blockage.
installation.
6. Glass soots.
7. Flame burns blue
and lifts off burner.
a. Flame impingement.
Adjust the log set so that the flame does not excessively impinge on it.
Check that logs are placed according to installation instructions.
b. Improper shutter
setting.
Adjust the air shutter at the base of the burner.
c. Debris around
opening at base of
burner.
Inspect the opening at the base of the burner. NO MATERIAL SHOULD
BE PLACED IN THIS OPENING.
a. Insufficient
oxygen being supplied.
Ensure that the vent cap is installed properly and free of debris. Ensure
that the vent system joints are tight and have no leaks.
Ensure that no debris has been placed at the base of, or in the area of
the air holes in the center of the base pan beneath the burner.
Ensure that the glass is tightened properly on the appliance, particularly on top corners.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 37
11
Although the frequency of your appliance servicing and
maintenance will depend on use and the type of installation,
a qualified service technician should perform an appliance
check-up at the beginning of each heating season.
CAUTION
Handle glass assembly with care.
NOTE: Clean glass after initial 3-4 hours
operation.
fi
Risk of injury or property damage.
• Turn off gas.
• Turn off electricity to appliance.
• Ensure appliance is completely cooled.
• Replace front and glass, if removed.
• Reseal and reinstall any venting removed for servicing.
•
•
•
•
•
Avoid striking, scratching or slamming glass.
Do NOT use abrasive cleaners.
Use a hard water deposit glass cleaner on white film.
Do NOT clean glass when hot.
Turn off appliance after 3-4 hours of operation and ALLOW
TO COOL.
• Remove and clean glass assembly.
• Replace glass assembly and operate appliance for additional
12 hours.
Refer to maintenance instructions.
Annual inspection by qualified technician recommended.
•
•
•
•
•
•
Condition of glass, glass assembly and glass seal.
Obstructions of combustion and ventilation air.
Obstructions of termination cap.
Burner ignition and operation.
Burner air shutter adjustment
Gas connections and fittings.
Clean:
• Glass
• Air passageways, grilles,
control compartment
• Burner, burner ports.
•
•
•
•
Fire
Delayed ignition or explosion
Exposure to combustion fumes
Odors
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
• Combustible materials blocking cap may
ignite.
• Restricted air flow affects burner operation.
Page 38
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Doors
1. Inspect for scratches, dents or other damage and repair as necessary.
2. Verify no obstructions to air flow.
3. Verify maintenance of proper clearance to combustible household objects.
Gasket Seal, Glass
Assembly and Glass
1. Inspect gasket seal and its condition.
2. Inspect glass for scratches and nicks that can lead to breakage when exposed to heat.
3. Confirm there is no damage to glass or glass frame, Replace as necessary.
4. Verify that latches engage properly and glass attachment components are intact and operating properly. Replace as necessary.
5. Clean glass. Replace glass assembly if severely coated with silicate deposits that cannot be
removed.
Valve Compartment
and Firebox Top
1. Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution when cleaning these
areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided.
2. Remove any foreign objects.
3. Verify unobstructed air circulation.
Logs
1. Inspect for broken, damaged, or missing logs. Replace as necessary.
2. Verify correct log placement and no flame impingement causing sooting. Correct as necessary.
Firebox
1. Inspect for paint condition, warpage, corrosion or perforation. Sand and repaint as necessary.
2. Replace appliance if firebox has been perforated.
Burner Ignition and
Operation
1. Verify burner is properly secured and aligned with pilot or igniter.
2. Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if
necessary.
3. Replace ember material with new dime-size and shape pieces. Do not block ports or obstruct
lighting paths.
4. Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.
5. Inspect for lifting and other flame problems.
6. Inspect orifice for soot, dirt or corrosion.
7. Verify manifold and inlet pressures. Adjust regulator as required.
8. Inspect pilot flame strength. Clean or replace orifice as necessary.
9. Inspect thermocouple/thermopile sensor rod for soot, corrosion and deterioration. Clean with
emery cloth or replace as required.
10. Verify millivolt output. Replace as necessary.
Venting
1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc.
2. Confirm that termination cap remains clear and unobstructed by plants, etc.
3. Verify that termination cap clearance to subsequent construction (building additions, decks,
fences or sheds) has been maintained.
4. Inspect for corrosion or separation.
5. Verify weather stripping, sealing and flashing remains intact.
Remote Controls
1. Verify operation of remote.
2. Replace batteries in remote transmitters and battery-powered receivers.
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 39
Page 40
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
12
Dimensions are actual appliance dimensions. Use for reference only. For clearances refer to Section 3.
A
C
D
B
E
F
G
H
I
K
J
A
22-1/2
572
G
11-1/4
286
B
28-1/2
724
H
7-3/4
197
C
16
406
I
5
127
D
18-3/4
476
J
17-7/16
443
E
28-1/2
724
K
16
406
F
22-1/2
572
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 41
6-1/2 in.
165 mm
6-9/16 in.
167 mm
9-7/16 in.
240 mm
6-9/16 in.
167 mm 9-1/4 in.
235 mm
6 in.
152 mm
6-5/8 in.
168 mm
6-5/8 in.
168 mm
9-3/4 in.
248 mm
SLP45
SLP90
6-5/8 in.
168 mm
7-1/4 in.
184 mm
5-1/4 in.
133 mm
6-5/8 in.
168 mm
6-5/8 in.
168 mm
6-5/8 in.
168 mm
6-9/16 in.
167 mm
13-1/4 in.
337 mm
7-1/4 in.
184 mm
SLP6
SLP4
6-5/8 in.
168 mm
6-9/16 in.
167 mm
SLP12A
SLP6A
6-5/8 in.
168 mm
6-5/8 in.
168 mm
49-1/4 in.
1251 mm
37-1/4 in.
946 mm
6-5/8 in.
168 mm
25-1/4 in.
641 mm
13-1/4 in.
337 mm
6-9/16 in.
167 mm
SLP12
6-9/16 in.
167 mm
SLP24
6-9/16 in.
167 mm
SLP36
Note: Pipes overlap 1-3/8 inches (34.93 mm) at each joint.
Page 42
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
6-9/16 in.
167 mm
SLP48
TERMINATION KITS
COMPONENTS
SLP-WT-BK
Ceiling Support / Wall Thimble, Black
SLP-TRAP2
SLP-CCS-BK
Cathedral Ceiling Support, Black
SLP-TVHW
Vertical Termination Cap - High Wind
SLP6-BK
6 inch Pipe Length, Black
SLP-SK-BK
SLP4-BK
9 inch Pipe Length, Black
Horizontal Termination Kit (includes 904B,
930D, SLK-01TRD)
SLP12-BK
12 inch Pipe Length, Black
SLK-SNKD
Snorkel Kit
SLP34-BK
24 inch Pipe Length, Black
SLP36-BK
36 inch Pipe Length, Black
SLP48-BK
48 inch Pipe Length, Black
LINK-STOVE Adapter Kit (includes 30 ft. of 4 inch flex,
apapters, wall thimble, masonry
& ZC flashing, 991DA cap and hardware
package
SLP6A-BK
11 inch - 14-5/8 inch Pipe Length, Black
VPK-DV
Vinyl Siding Protector Kit
SLP12A-BK
12 inch - 17 inch Pipe, Adjustable, Black
SLP-HHW2
SLP45-BK
45 degree Elbow, Black
HHW2 Horizontal High Wind Cap
(recommended for optimal performance)
SLP90-BK
90 degree Elbow, Black
899-4491
SLP4
4 inch Pipe
SLP6
6 inch Pipe
SLP12
12 inch Pipe
HHW2K Horizontal Kit (one 90 degree
black wall thimble, 24 inch black
pipe, 11 inch - 14-5/8 inch adjustable
vent, HHW2 termination cap)
SLP24
24 inch Pipe
844-8921
RHVK Snorkel Kit (with Dura-Vent parts
911B and 940)
SLP36
36 inch Pipe
SLP48
48 inch Pipe
46DVA-SC
Storm Collar
SLP45
45 degree Elbow
46DVA-FS
Ceiling Firestop
SLP90
90 degree Elbow
46DVA-WS
Wall Strap
SLP6A
3-6 in. Adjustable Pipe Extension
46DVA-IS
Attic Insulation Shield
SLP12A
3-12 in. Adjustable Pipe Extension
46DVA-GK
Chimney Liner Termination Kit
SLP-RF6
0/12 - 6/12 Roof Flashing
46DVA-GCL
Co-axial / Co-lineal Appliance Connector
SLP-RF12
7/12 - 12/12 Roof Flashing
46DVA-KMC
SL-SCD
Storm Collar
Retrofit Adj. Chimney Connector Retrofit
Chimney Connector Plate
SLP-FS
Ceiling Firestop
SLP-WS
Wall Firestop
SLP-HVS
Pipe Support Hanger
950
Vinyl Protector Kit - SL Pipe
DRC-RADIUS
Decorative Radius Cover
HTI-DV-WT
Wall Thimble
RF4-8
Roof Flashing
Trapezoid Termination Kit
MISCELLANEOUS
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 43
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
Components Covered
Electric Venting
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
X
Firepots and burnpots
5 years
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Page 1 of 2
Page 47
(continued)
WARRANTY CONDITIONS:
‡
‡
‡
‡
7KLVZDUUDQW\RQO\FRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHGWKURXJKDQ++7DXWKRUL]HGGHDOHURUGLVWULEXWRU$OLVWRI
++7DXWKRUL]HGGHDOHUVLVDYDLODEOHRQWKH++7EUDQGHGZHEVLWHV
7KLVZDUUDQW\LVRQO\YDOLGZKLOHWKH++7DSSOLDQFHUHPDLQVDWWKHVLWHRIRULJLQDOLQVWDOODWLRQ
&RQWDFW\RXULQVWDOOLQJGHDOHUIRUZDUUDQW\VHUYLFH,IWKHLQVWDOOLQJGHDOHULVXQDEOHWRSURYLGHQHFHVVDU\SDUWVFRQWDFW
WKHQHDUHVW++7DXWKRUL]HGGHDOHURUVXSSOLHU$GGLWLRQDOVHUYLFHIHHVPD\DSSO\LI\RXDUHVHHNLQJZDUUDQW\VHUYLFH
IURPDGHDOHURWKHUWKDQWKHGHDOHUIURPZKRP\RXRULJLQDOO\SXUFKDVHGWKHSURGXFW
&KHFNZLWK\RXUGHDOHULQDGYDQFHIRUDQ\FRVWVWR\RXZKHQDUUDQJLQJDZDUUDQW\FDOO7UDYHODQGVKLSSLQJFKDUJHV
IRUSDUWVDUHQRWFRYHUHGE\WKLVZDUUDQW\
WARRANTY EXCLUSIONS:
7KLVZDUUDQW\GRHVQRWFRYHUWKHIROORZLQJ
‡ &KDQJHVLQVXUIDFHILQLVKHVDVDUHVXOWRIQRUPDOXVH$VDKHDWLQJDSSOLDQFHVRPHFKDQJHVLQFRORURILQWHULRUDQG
H[WHULRUVXUIDFHILQLVKHVPD\RFFXU7KLVLVQRWDIODZDQGLVQRWFRYHUHGXQGHUZDUUDQW\
‡ 'DPDJHWRSULQWHGSODWHGRUHQDPHOHGVXUIDFHVFDXVHGE\ILQJHUSULQWVDFFLGHQWVPLVXVHVFUDWFKHVPHOWHGLWHPV
RURWKHUH[WHUQDOVRXUFHVDQGUHVLGXHVOHIWRQWKHSODWHGVXUIDFHVIURPWKHXVHRIDEUDVLYHFOHDQHUVRUSROLVKHV
‡ 5HSDLURUUHSODFHPHQWRISDUWVWKDWDUHVXEMHFWWRQRUPDOZHDUDQGWHDUGXULQJWKHZDUUDQW\SHULRG7KHVHSDUWV
LQFOXGHSDLQWZRRGSHOOHWDQGFRDOJDVNHWVILUHEULFNVJUDWHVIODPHJXLGHVOLJKWEXOEVEDWWHULHVDQGWKHGLVFRORUDWLRQRIJODVV
‡ 0LQRUH[SDQVLRQFRQWUDFWLRQRUPRYHPHQWRIFHUWDLQSDUWVFDXVLQJQRLVH7KHVHFRQGLWLRQVDUHQRUPDODQGFRPSODLQWVUHODWHGWRWKLVQRLVHDUHQRWFRYHUHGE\WKLVZDUUDQW\
‡ 'DPDJHVUHVXOWLQJIURPIDLOXUHWRLQVWDOORSHUDWHRUPDLQWDLQWKHDSSOLDQFHLQDFFRUGDQFHZLWKWKHLQVWDOODWLRQ
LQVWUXFWLRQVRSHUDWLQJLQVWUXFWLRQVDQGOLVWLQJDJHQWLGHQWLILFDWLRQODEHOIXUQLVKHGZLWKWKHDSSOLDQFHIDLOXUHWR
LQVWDOOWKHDSSOLDQFHLQDFFRUGDQFHZLWKORFDOEXLOGLQJFRGHVVKLSSLQJRULPSURSHUKDQGOLQJLPSURSHURSHUDWLRQDEXVHPLVXVHFRQWLQXHGRSHUDWLRQZLWKGDPDJHGFRUURGHGRUIDLOHGFRPSRQHQWVDFFLGHQWRULPSURSHUO\
LQFRUUHFWO\SHUIRUPHGUHSDLUVHQYLURQPHQWDOFRQGLWLRQVLQDGHTXDWHYHQWLODWLRQQHJDWLYHSUHVVXUHRUGUDIWLQJ
FDXVHGE\WLJKWO\VHDOHGFRQVWUXFWLRQVLQVXIILFLHQWPDNHXSDLUVXSSO\RUKDQGOLQJGHYLFHVVXFKDVH[KDXVWIDQVRU
IRUFHGDLUIXUQDFHVRURWKHUVXFKFDXVHVXVHRIIXHOVRWKHUWKDQWKRVHVSHFLILHGLQWKHRSHUDWLQJLQVWUXFWLRQV
LQVWDOODWLRQRUXVHRIFRPSRQHQWVQRWVXSSOLHGZLWKWKHDSSOLDQFHRUDQ\RWKHUFRPSRQHQWVQRWH[SUHVVO\DXWKRUL]HG
DQGDSSURYHGE\++7PRGLILFDWLRQRIWKHDSSOLDQFHQRWH[SUHVVO\DXWKRUL]HGDQGDSSURYHGE\++7LQZULWLQJ
DQGRULQWHUUXSWLRQVRUIOXFWXDWLRQVRIHOHFWULFDOSRZHUVXSSO\WRWKHDSSOLDQFH
‡ 1RQ++7YHQWLQJFRPSRQHQWVKHDUWKFRPSRQHQWVRURWKHUDFFHVVRULHVXVHGLQFRQMXQFWLRQZLWKWKHDSSOLDQFH
‡ $Q\SDUWRIDSUHH[LVWLQJILUHSODFHV\VWHPLQZKLFKDQLQVHUWRUDGHFRUDWLYHJDVDSSOLDQFHLVLQVWDOOHG
‡ ++7¶VREOLJDWLRQXQGHUWKLVZDUUDQW\GRHVQRWH[WHQGWRWKHDSSOLDQFH¶VFDSDELOLW\WRKHDWWKHGHVLUHGVSDFH,QIRUPDWLRQLVSURYLGHGWRDVVLVWWKHFRQVXPHUDQGWKHGHDOHULQVHOHFWLQJWKHSURSHUDSSOLDQFHIRUWKHDSSOLFDWLRQ&RQVLGHUDWLRQPXVWEHJLYHQWRDSSOLDQFHORFDWLRQDQGFRQILJXUDWLRQHQYLURQPHQWDOFRQGLWLRQVLQVXODWLRQDQGDLUWLJKWQHVVRI
WKHVWUXFWXUH
This warranty is void if:
‡
‡
‡
7KHDSSOLDQFHKDVEHHQRYHUILUHGRURSHUDWHGLQDWPRVSKHUHVFRQWDPLQDWHGE\FKORULQHIOXRULQHRURWKHUGDPDJLQJ
FKHPLFDOV2YHUILULQJFDQEHLGHQWLILHGE\EXWQRWOLPLWHGWRZDUSHGSODWHVRUWXEHVUXVWFRORUHGFDVWLURQEXEEOLQJ
FUDFNLQJDQGGLVFRORUDWLRQRIVWHHORUHQDPHOILQLVKHV
7KHDSSOLDQFHLVVXEMHFWHGWRSURORQJHGSHULRGVRIGDPSQHVVRUFRQGHQVDWLRQ
7KHUHLVDQ\GDPDJHWRWKHDSSOLDQFHRURWKHUFRPSRQHQWVGXHWRZDWHURUZHDWKHUGDPDJHZKLFKLVWKHUHVXOWRIEXW
QRWOLPLWHGWRLPSURSHUFKLPQH\RUYHQWLQJLQVWDOODWLRQ
LIMITATIONS OF LIABILITY:
‡
7KHRZQHU¶VH[FOXVLYHUHPHG\DQG++7¶VVROHREOLJDWLRQXQGHUWKLVZDUUDQW\XQGHUDQ\RWKHUZDUUDQW\H[SUHVVRU
LPSOLHGRULQFRQWUDFWWRUWRURWKHUZLVHVKDOOEHOLPLWHGWRUHSODFHPHQWUHSDLURUUHIXQGDVVSHFLILHGDERYH,QQR
HYHQWZLOO++7EHOLDEOHIRUDQ\LQFLGHQWDORUFRQVHTXHQWLDOGDPDJHVFDXVHGE\GHIHFWVLQWKHDSSOLDQFH6RPHVWDWHV
GRQRWDOORZH[FOXVLRQVRUOLPLWDWLRQRILQFLGHQWDORUFRQVHTXHQWLDOGDPDJHVVRWKHVHOLPLWDWLRQVPD\QRWDSSO\WR\RX
7KLVZDUUDQW\JLYHV\RXVSHFLILFULJKWV\RXPD\DOVRKDYHRWKHUULJKWVZKLFKYDU\IURPVWDWHWRVWDWH(;&(3772
7+((;7(173529,'('%</$:++70$.(612(;35(66:$55$17,(627+(57+$17+(:$55$17<
63(&,),('+(5(,17+('85$7,212)$1<,03/,(':$55$17<,6/,0,7('72'85$7,212)7+(
(;35(66(':$55$17<63(&,),('$%29(
4021-645C 12-29-10
Page 48
Page 2 of 2
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
R
CONTACT INFORMATION:
fi
fi
CAUTION
Do NOT discard this manual.
• Important operating and maintenance
instructions included.
• Read, understand and follow these instructions for safe installation and operation.
• Leave this manual with party responsible
for use and operation.
Direct Vent Gas Appliance
SERIAL NUMBER:
__________________
______________________________________
DATE PURCHASED:
__________________
_______________________________________
DATE INSTALLED:
__________________
_______________________________________
DEALER TELEPHONE: __________________
This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487,
5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712,
6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.
2000-945
Page 49
Quadra-Fire • COLBAY-FS-B • 250-5195 Rev. R • 10/11
Download PDF