OREI UHD48-EX230-K 4x4 HDMI Matrix Extender User Manual

18Gbps 4 x 4 HDMI Matrix (70M)
VER 1.0
Thank you for purchasing this product
For optimum performance and safety, please read these instructions carefully before connecting,
operating or adjusting this product. Please keep this manual for future reference.
Surge protection device recommended
This product contains sensitive electrical components that may be damaged by electrical
spikes, surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly
recommended in order to protect and extend the life of your equipment.
Table of Contents
1. Introduction..................................................................................................................... 1
2. Features........................................................................................................................... 1
3. Package Contents........................................................................................................ 2
4. Specifications................................................................................................................ 2
5. Operation Controls and Functions.............................................................................. 4
5.1. Matrix Panel.......................................................................................................... 4
5.2. CAT Receiver Panel............................................................................................... 5
6. IR Remote..................................................................................................................... 6
7. IR Cable Pin Assignment.............................................................................................. 6
8. EDID Management........................................................................................................7
9. Web GUI User Guide.................................................................................................... 9
10. RS-232 Control Command........................................................................................... 16
11. Application Example................................................................................................... 21
1. Introduction
The 18Gbps 4x4 HDMI Matrix can connect four HDMI sources to eight displays. It features
four HDMI outputs and each HDMI output is mirrored to provide a CAT-Cable output which
runs simultaneously. It supports the transmission of video (resolution is up to 1080p Full HD
and 4Kx2K@60Hz 4:4:4) and supports HD digital audio formats such as LPCM 7.1CH, Dolby
TrueHD, Dolby Digital Plus and DTS-HD Master Audio. Connect a CAT Receiver to each of
the CAT-Cable outputs to extend the HDMI signal up to 230ft/70m for multi-room connectivity.
Each HDMI output supports 4K2K to 1080P downscaler independently. The product supports
control via front panel buttons, IR remote, RS-232, LAN, and Web GUI.
2. Features
☆ HDMI 2.0b and HDCP 2.2/1.x compliant
☆ Video resolution up to 4K2K@60Hz (YUV 4:4:4) on all HDMI & CAT ports
☆ 4 HDMI inputs, 4 HDMI & CAT mirrored outputs
☆ HDMI ports support 18Gbps lossless uncompressed video bandwidth
☆ Support 4K->1080P Down Scaler for each output port
☆ HDR, HDR10, HDR10+, Dolby Vision, HLG are supported
☆ CAT output can extend the transmission distance up to 230ft/70m via a single CAT6 cable
☆ HDMI audio pass-through up to 7.1CH HD audio (LPCM, Dolby TrueHD and DTS-HD
Master Audio)
☆ Advanced EDID management and CEC control are supported
☆ 12V POC on all CAT ports
☆ Control via front panel buttons, IR remote, RS-232, LAN and Web GUI
- 1 / 21 -
3. Package Contents
① 1 x 18Gbps 4x4 HDMI Matrix
② 4 x CAT Receiver
③ 1 x Matrix IR Remote
④ 1 x 12V2.5A Power Supply
⑤ 1 x RS-232 serial Cable (1.5 meters, male to female head)
⑥ 1 x 3-pin Phoenix Connector
⑦ 4 x IR Blaster Cable (1.5 meters)
⑧ 4 x IR Receiver Cable (1.5 meters)
⑨ 10 x Mounting Ear (Matrix and Receiver)
⑩ 1x User Manual
4. Specifications
Technical
HDMI Compliance
HDCP Compliance
Video Bandwidth
HDMI 2.0b
HDCP 2.2/1.x
18Gbps
Video Resolution
Color Space
Up to 4K2K@50/60Hz (4:4:4)
RGB 4:4:4, YCbCr 4:4:4/4:2:2/4:2:0
8-bit, 10-bit, 12-bit (1080p@60Hz)
8-bit (4K2K@60Hz YUV4:4:4)
8-bit，10-bit,12-bit (4K2K@60Hz YCbCr 4:2:2/4:2:0）
HDR10, HDR10+, Dolby Vision, HLG
LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD,
Dolby Digital Plus (DD+), DTS-ES, DTS HD Master,
DTS HD-HRA, DTS-X
230ft / 70m (via a single CAT6 cable)
Human-body Model:
±8kV (Air-gap discharge) , ±4kV (Contact discharge)
Color Depth
HDR
HDMI Audio Formats
Transmission Distance
ESD Protection
- 2 / 21 -
Connection
Matrix
Inputs: 4 x HDMI Type A [19-pin female]
Outputs: 4 x HDMI Type A [19-pin female]
4 x CAT port [RJ45]
4 x IR OUT [3.5mm Stereo Mini-jack]
Controls: 1 x TCP/IP [RJ45]
1 x RS-232 [3-pin phoenix connector]
CAT Receiver
Inputs: 1x IR IN [3.5mm Stereo Mini-jack]
1x CAT port [RJ45]
Output: 1x HDMI Type A [19-pin female]
Control: 1x SERVICE [Micro USB, Update port]
Mechanical
Housing
Metal Enclosure
Color
Black
Dimensions
Matrix: 320mm (W) × 100mm (D) × 36mm (H)
Receiver: 61mm (W) x 88mm (D) x 18mm (H)
Weight
Matrix: 915g, Receiver: 155g
Power Supply
Input: AC 90 - 260V 50/60Hz
Output: DC 12V/2.5A
(US/EU standards, CE/FCC/UL certified)
Power Consumption
19.68W (Max)
Operating Temperature
0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature
-20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity
20~90% RH (non-condensing)
Resolution / Cable length
4K60 Feet / Meters
4K30 Feet / Meters
1080P60 Feet / Meters
16ft / 5M
32ft / 10M
50ft / 15M
HDMI IN / OUT
The use of “Premium High Speed HDMI” cable is highly recommended.
- 3 / 21 -
5. Operation Controls and Functions
5.1 Matrix Panel
Front Panel
ON
1
OFF
2
2
1
NO.
1
3
OUT 1
IR
2
3
1
OUT 2
3
1
2
OUT 3
3
OUT 4
4
3
Name
2
Function Description
4
1
Power switch
Press the switch to power on/off the Matrix.
2
Power LED
The LED will illuminate in green when the Matrix is working
normally, and red when the Matrix is on standby.
3
IR Window
IR receiver window, it only receives the IR remote signal
from this Matrix.
4
OUT 1-4 buttons Press the OUT 1/2/3/4 button to circularly select HDMI source
&
signal for the corresponding output port, then the
Source LED 1~4 corresponding source LED will be on.
Rear Panel
OUTPUT 1
RS-232
TX
TCP/IP
1
2
1
1
TCP/IP port
2
RS-232 port
3
OUTPUT 1-4
ports
5
6
IR OUT 1-4
ports
HDMI IN 1-4
ports
DC 12V
IR
4
3
Name
OUTPUT 3
OUTPUT 2
4
2
HDMI
OUT
OUTPUT 4
RJ45
RJ45
HDMI
No.
4
OUT
RJ45
RX
1
2
HDMI IN
5
3
3
4
HDMI
RJ45
3
3
IR
4
4
HDMI
DC 12V
3
6
Function Description
The link port for TCP/IP control. Connect to an active Ethernet
link with an RJ45 cable.
RS-232 command control port. Connect to a PC or control
system with a D-Sub 9-pin cable to control the Matrix.
HDMI output ports, connect to HDMI display devices such as
TV or monitor with HDMI cable.
CAT mirrored output ports, connect to CAT Receivers with CAT
cable.
Connect to IR blaster cable, the IR signal is from the “IR IN”
port of the CAT Receiver.
HDMI signal input ports, connect to HDMI source device such
as DVD or PS4 with HDMI cable.
DC 12V power supply port.
- 4 / 21 -
5.2 CAT Receiver Panel
No.
1
2
3
4
5
6
7
HDMI OUT
CAT IN
1
3 2 4
Name
SERVICE IR IN
5
6
DC 12V
7
Function Description
HDMI output port, connect to HDMI display device such as
HDMI OUT
TV or Projector with an HDMI cable.
Connect to the CAT OUTPUT port on the Matrix with a CAT
CAT IN
cable.
Power Indicator When the receiver is powered on, the power indicator lamp
Lamp (Green) will be on.
Data signal
When there is signal transmission between the Matrix and the
Indicator Lamp
receiver, the lamp will be on.
(Orange)
SERVICE port Used for firmware update.
Connect to the IR Receiver cable. The IR signal will send to
IR IN
the IR OUT port of the Matrix.
Plug DC 12V/1A power supply into the unit and connect the
adapter to an AC outlet.
DC 12V
(Note: The CAT receiver also can be powered by the Matrix
via a CAT cable. )
- 5 / 21 -
6. IR Remote
1
2
3
4
5
① Power on or Standby: Power on the Matrix or set
it to standby mode.
② Output 1: Press 1\2\3\4 button to select input source to
HDMI OUTPUT 1.
③ Output 2: Press 1\2\3\4 button to select input source to
HDMI OUTPUT 2.
④ Output 3: Press 1\2\3\4 button to select input source to
HDMI OUTPUT 3.
⑤ Output 4: Press 1\2\3\4 button to select input source to
HDMI OUTPUT 4.
: Select the last or next input source button.
7. IR Cable Pin Assignment
IR RECEIVER
IR BLASTER
- 6 / 21 -
8. EDID Management
This Matrix has 21 factory defined EDID settings, 2 user-defined EDID modes and 8 copy EDID
modes. You can select defined EDID mode or copy EDID mode to input port through RS-232
control or Web GUI.
RS-232 control operation: Connect the Matrix to PC with a serial cable, then open a Serial
Command tool on PC to send ASCII command “s edid in x from z!” to set EDID. For details,
please refer to “EDID Setting” in the ASCII command list of “10. RS-232 Control Command”.
Web GUI Operation: Please check the EDID management in the “Input page” of “9. Web
GUI User Guide”.
- 7 / 21 -
The defined EDID setting list of the product is shown as below:
EDID Mode
1
2
3
4
EDID Description
1080P, Stereo Audio 2.0
1080P, Dolby/DTS 5.1
1080P, HD Audio 7.1
1080I, Stereo Audio 2.0
5
6
7
1080I, Dolby/DTS 5.1
1080I, HD Audio 7.1
3D, Stereo Audio 2.0
8
9
10
3D, Dolby/DTS 5.1
3D, HD Audio 7.1
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
4K2K30_444, Stereo Audio 2.0
4K2K30_444, Dolby/DTS 5.1
4K2K30_444, HD Audio 7.1
4K2K60_420, Stereo Audio 2.0
4K2K60_420, Dolby/DTS 5.1
4K2K60_420, HD Audio 7.1
4K2K60_444, Stereo Audio 2.0
4K2K60_444, Dolby/DTS 5.1
4K2K60_444, HD Audio 7.1
4K2K60, Stereo Audio 2.0 HDR
4K2K60, Dolby/DTS 5.1 HDR
4K2K60, HD Audio 7.1HDR
User Define1
User Define2
COPY_FROM_HDMI 1
COPY_FROM_HDMI 2
COPY_FROM_HDMI 3
COPY_FROM_HDMI 4
COPY_FROM_CAT 1
COPY_FROM_CAT 2
COPY_FROM_CAT 3
COPY_FROM_CAT 4
- 8 / 21 -
9. Web GUI User Guide
The Matrix can be controlled by Web GUI. The operation method is shown as below:
Step 1: Get the current IP Address.
The default IP address is 192.168.1.100. You can get the current Matrix IP address via RS-232
control. Send the ASCII command “ r ipconfig!” through a Serial Command tool, then you’ll get
the feedback information as shown below:
IP:192.168.2.209 in the above figure is the current Matrix IP address (this IP address is
variable, depending on what the specific machine returns).
For the details of RS-232 control, please refer to “10. RS-232 Control Command”.
Step 2: Connect the TCP/IP port of the Matrix to a PC with an UTP cable (as shown in the
following figure), and set the IP address of the PC to be in the same network segment with
the Matrix.
NAL
NAL
PC
Step 3: Input the current IP address of Matrix into your browser on the PC to enter Web GUI page.
- 9/ 21 -
After entering the Web GUI page, there will be a Login page, as shown below:
Select the Username from the list and enter the password. The default passwords are:
Username
Password
User
user
Admin
admin
After entering the password, click the “LOGIN” button and the following Status page will
appear.
■ Status Page
The Status page provides basic information about the product model, installed firmware
version and the network settings of the device.
- 10 / 21 -
■ Video Page
You can do the following operations on the Video page:
① Output: The current device’s OUTPUT port. You can select signal source for it.
② Input: You can click the drop-down menu to select signal source for the corresponding
OUTPUT port .
③ Presets Name: You can name the current scene with maximum length of 12 characters
(Chinese name is unsupported).
④ Presets Set: You can restore the settings of the last saved audio-video matrix switching
relationship.
⑤ Presets Save: You can save audio-video matrix switching relationship.
⑥ Presets Clear: You can clear the saved audio-video matrix switching relationship.
■ Input Page
You can do the following operations on the Input page:
① Inputs: Input channel of the device.
② Active: It indicates whether the channel is connected to a signal source.
③ Name: The input channel’s name. You can modify it by entering the corresponding name
(max length: 12 characters) in the input box (Chinese name is unsupported).
④ EDID: You can set the current channel’s EDID. The specific operation is as follows:
- 11 / 21 -
Set EDID for the User
Click the “Browse” button, then select the bin file. If you select the wrong EDID file, there will
be a prompt, as shown in the following figure:
Make sure to select the correct file, then you can check the name of the selected file. Select
“User 1” or “User 2”, then click “Upload”. After successful setting, it will prompt as follows:
Download the EDID File for the Corresponding Input Channel
Click the drop-down box of “Select EDID File” to select the corresponding input channel. Then
click “Download” to download the corresponding EDID file.
■ Output Page
You can do the following operations on the Output page:
① Outputs: Output channel of the device.
② Name: The current output channel’s name. You can modify it by entering the corresponding
name (max length: 12 characters) in the input box (Chinese name is unsupported).
③ Type: The current output channel’s type (HDMI or CAT).
④ Cable: It indicates the connection status of output ports. When the output port is connected
to the display, it shows green, otherwise, it shows gray.
⑤ Scaler Mode: Set the current output resolution mode.
⑥ Stream: Turn on/off the output stream.
- 12 / 21 -
■ CEC Page
You can perform CEC management on this page:
① Input Control: You can control the operation of each input source by pressing the icons
on the page. (You can control multiple inputs simultaneously.)
② Output Control: You can control the operation of each display, such as power on/off,
volume +/-, active source switching. (You can control multiple outputs simultaneously.)
■ Network Page
Set the Default Network
Click “Set Network Defaults” button, there will be a prompt, as shown in the following figure:
- 13 / 21 -
Click “OK” to search the IP Address again, as shown in the figure below.
After searching is completed, it will switch to the login page, the default network setting is
completed.
Modify User Password
Click the “User” button, enter the correct Old Password, New Password, and Confirm
Password, then click “Save”. After successful modification, there will be a prompt, as shown
in the following figure:
Note: Input rules for changing passwords:
(1) The password can’t be empty.
(2) New Password can’t be the same as Old Password.
(3) New Password and Confirm Password must be the same.
Modify Network Setting
Modify the Mode/IP Address/Gateway/Subnet Mask/Telnet Port as required, click “Save”
to save the settings, then it will come into effect.
After modification, if the Mode is “Static”, it will switch to the corresponding IP Address;
if the Mode is “DHCP”, it will automatically search and switch to the IP Address assigned
by the router.
- 14 / 21 -
■ System Page
① Panel Lock: Click to lock/unlock panel buttons. “On” indicates that panel buttons are
unavailable; “Off” indicates panel buttons are available.
② Beep: Click to turn on/off the beep.
③ Serial Baud Rate: Click the value to set the Serial Baud Rate.
④ Firmware Update: Click “Browse” to select the update file, then click “Update” to complete
firmware update.
⑤ Factory Reset: You can reset the machine to factory defaults by clicking “Reset”.
⑥ Reboot: You can reboot the machine by clicking “Reboot”.
Note: After reset/reboot, it will switch to the login page.
- 15 / 21 -
10. RS-232 Control Command
The product also supports RS-232 control. You need a serial cable with RS-232 phoenix
connector and RS-232 male head. The RS-232 phoenix connector is connected to the Matrix,
and the RS-232 male head of the serial cable is connected to the RS-232 female head of an
RS-232 to USB cable, while the USB head of the RS-232 to USB cable is connected to a PC.
The connection method is as follows:
TX
Ground
RX
3-pin Phoenix Connector
RS-232
RS-232 to USB cable
PC
Then, open a Serial Command tool on PC to send ASCII command to control the Matrix.
The ASCII command list about the product is shown as below.
ASCII Command
Serial port protocol. Baud rate: 115200,
Data bits: 8bit, Stop bits:1, Check bit: 0
x - Parameter 1
y - Parameter 2
! - Delimiter
Command Code
Function Description
Example
Feedback
Default Setting
Power
Power on
s power z!
Power on/off the device,z=0~1
(z=0 power off, z=1 power on)
s power 1!
r power!
Get current power state
r power!
System Initializing... power on
Initialization Finished!
FW version x.xx.xx
power on/power off
Reboot...
Reboot the device
s reboot!
help!
List all commands
help!
r type!
Get device model
r type!
r status!
Get device current status
r status!
r fw version!
Get Firmware version
r fw version!
s reboot!
System Initializing...
Initialization Finished!
FW version x.xx.xx
System Setup
- 16 / 21 -
HDP-MXB44D70
Get the unit all status:
power, beep, lock, in/
out connection, video/
audio crosspoint,
edid, scaler,hdcp,
network status
MCU BOOT:Vx.xx.xx
MCU APP :Vx.xx.xx
WEB GUI :Vx.xx
Command Code
Function Description
Example
Feedback
r link in x!
Get the connection status of the
x input port，x=0~4(0=all)
r link in 1!
hdmi input 1: connect
r link out y!
Get the connection status of the
y output port，y=0~4(0=all)
r link out 1!
hdmi output 1: connect
s reset!
Reset to factory defaults
s reset!
s beep z!
Enable/Disable buzzer function,
z=0~1(z=0 beep off, z=1 beep on) s beep 1!
r beep!
Get buzzer state
s lock z!
Lock/Unlock front panel button,
z=0~1 (z=0 lock off,z=1 lock on)
Get panel button lock state
Save switch state between all
output port and the input port to
preset z, z=1~4
Call saved preset z scenarios,
z=1~4
Clear stored preset z scenarios,
z=1~4
r lock!
s save preset z!
s recall preset z!
s clear preset z!
Default Setting
Reset to factory defaults
System Initializing...
Initialization Finished!
FW version x.xx.xx
beep on
beep on
beep off
r beep!
beep on / beep off
s lock 1!
panel button lock on
panel button lock off
r lock!
panel button lock on/off
s save preset 1!
save to preset 1
panel button
lock off
s recall preset 1! recall from preset 1
s clear preset 1!
clear preset 1
r preset 1!
video/audio crosspoint
r preset z!
Get preset z information, z=1~4
s baud rate xxx!
Set the serial port baud rate of
s baud rate
RS02 module, z=(115200,57600,
115200!
38400,19200,9600,4800)
Baudrate:115200
r baud rate!
Get the serial port baud rate of
RS02 module
r baud rate!
Baudrate:115200
s id z!
Set the control ID of the product,
z=000~999
s id 888!
id 888
0
s in x av out y!
Set input x to output y，
x=1~4，y=0~4(0=all)
s in 1 av out 2!
input 1 -> output 2
ptp
r av out y!
Get output y signal status
y=0~4(0=all)
r av out 0!
input 1 -> output 1
input 2 -> output 2
input 3 -> output 3
input 4 -> output 4
Output Setting
Set hdmi output y stream on/off,
s hdmi y stream z! y=0~4(0=all)
z=0~1(0:disable,1:enable)
r hdmi y stream!
s cat y stream z!
enable hdmi output 1
stream
disable hdmi output 1
s hdmi 1 stream 1! stream
enable
s hdmi 0 stream 1! enable hdmi all outputs
stream
disable hdmi all outputs
stream
Get hdmi output y stream status, r hdmi 1 stream! enable hdmi output 1
y=0~4(0=all)
stream
enable cat output 1
stream
disable cat output 1
Set cat output y stream on/off,
s cat 1 stream 1! stream
y=0~4(0=all)
enable
z=0~1(0:disable,1:enable)
s cat 0 stream 1! enable cat all outputs
stream
disable cat all outputs
stream
- 17 / 21 -
Command Code
Function Description
r cat y stream!
Get cat output y stream status,
y=0~4(0=all)
Set hdmi output y port output
s hdmi y scaler z! scaler mode，y=0~4(0=all),
z=1~3(1=bypass,2=4k->1080p,
3=Auto)
r hdmi y scaler!
Get hdmi output y port output
mode y=0~4(0=all)
Example
r cat 1 stream!
Feedback
Default Setting
enable cat output 1
stream
hdmi output 1 set to
s hdmi 1 scaler 1! bypass mode
hdmi all outputs
set to bypass
hdmi
all
outputs
set
to
mode
s hdmi 0 scaler 1!
bypass mode
r hdmi 1 scaler!
hdmi output 1 set to
bypass mode
EDID Setting
Set input x EDID from default
EDID z,
x=0~4(0=all),z=1~31
1, 1080p,Stereo Audio 2.0
2, 1080p,Dolby/DTS 5.1
3, 1080p,HD Audio 7.1
4, 1080i,Stereo Audio 2.0
5, 1080i,Dolby/DTS 5.1
6, 1080i,HD Audio 7.1
7, 3D,Stereo Audio 2.0
8, 3D,Dolby/DTS 5.1
9, 3D,HD Audio 7.1
10, 4K2K30_444,Stereo Audio 2.0
11, 4K2K30_444,Dolby/DTS 5.1
12, 4K2K30_444,HD Audio 7.1
13, 4K2K60_420,Stereo Audio 2.0
input 1 EDID:1080p,
14, 4K2K60_420,Dolby/DTS 5.1
s edid in 1 from 1! Stereo Audio 2.0
15, 4K2K60_420,HD Audio 7.1
1080p,
16, 4K2K60_444,Stereo Audio 2.0
Stereo Audio 2.0
s edid in x from z! 17, 4K2K60_444,Dolby/DTS 5.1
18, 4K2K60_444,HD Audio 7.1
s edid in 0 from 1! all inputs EDID:1080p,
19, 4K2K60_444,Stereo Audio 2.0
Stereo Audio 2.0
HDR
20, 4K2K60_444,Dolby/DTS 5.1
HDR
21, 4K2K60_444,HD Audio 7.1
HDR
22, User define1
23, User define2
24, copy from hdmi output 1
25, copy from hdmi output 2
26, copy from hdmi output 3
27, copy from hdmi output 4
28, copy from cat output 1
29, copy from cat output 2
30, copy from cat output 3
31, copy from cat output 4
r edid in x!
Get EDID status of the input x，
x=0~4(0=all input)
r edid data hdmi y! Get the EDID data of the hdmi
output y port，y=1~4
r edid in 0!
input1 EDID: 4K2K60_
444,Stereo Audio 2.0
input2 EDID: 4K2K60_
444,Stereo Audio 2.0
input3 EDID: 4K2K60_
444,Stereo Audio 2.0
input4 EDID: 4K2K60_
444,Stereo Audio 2.0
EDID: 00 FF FF FF FF
r edid data hdmi 1! FF FF 00 ………
hdmi output 1:
disconnect
CEC Setting
s cec in x on!
s cec in x off!
set input x power on by CEC,
x=0~4(0=all input)
set input x power off by CEC,
x=0~4(0=all input)
s cec in 1 on!
input 1 power on
s cec in 1 off!
input 1 power off
- 18 / 21 -
Command Code
s cec in x menu!
s cec in x back!
s cec in x up!
s cec in x down!
s cec in x left!
s cec in x right!
s cec in x enter!
s cec in x play!
s cec in x pause!
Example
Function Description
Feedback
set input x open menu by CEC,
s cec in 1 menu!
x=0~4(0=all input)
set input x back operation by
s cec in 1 back!
CEC, x=0~4(0=all input)
set input x menu up operation by s cec in 1 up!
CEC, x=0~4(0=all input)
input 1 menu up
operation
set input x menu down operation s cec in 1 down!
by CEC, x=0~4(0=all input)
set input x menu left operation by s cec in 1 left!
CEC, x=0~4(0=all input)
input 1 menu down
operation
input 1 menu left
operation
set input x menu right operation
by CEC, x=0~4(0=all input)
set input x menu enter operation
by CEC, x=0~4(0=all input)
input 1 menu right
operation
input 1 menu enter
operation
set input x play by CEC,
x=0~4(0=all input)
set input x pause by CEC,
x=0~4(0=all input)
s cec in 1 right!
s cec in 1 enter!
input 1 open menu
input 1 back operation
s cec in 1 play!
input 1 play operation
s cec in 1 pause!
input 1 pause
operation
s cec in x stop!
set input x stop by CEC,
x=0~4(0=all input)
s cec in 1 stop!
input 1 stop operation
s cec in x rew!
set input x rewind by CEC,
x=0~4(0=all input)
s cec in 1 rew!
input 1 rewind
operation
s cec in x mute!
set input x volume mute by CEC,
s cec in 1 mute!
x=0~4(0=all input)
input 1 volume mute
s cec in x vol-!
set input x volume down by CEC,
s cec in 1 vol-!
x=0~4(0=all input)
input 1 volume down
s cec in x vol+!
set input x volume up by CEC,
x=0~4(0=all input)
s cec in 1 vol+!
input 1 volume up
s cec in x ff!
set input x fast forward by CEC,
x=0~4(0=all input)
s cec in 1 ff!
input 1 fast forward
operation
s cec in x previous!
set input x previous by CEC,
x=0~4(0=all input)
s cec in 1 previous!
input 1 previous
operation
s cec in x next!
set input x next by CEC,
x=0~4(0=all input)
s cec in 1 next!
input 1 next operation
s cec hdmi out y
on!
set hdmi output y power on by
CEC, y=0~4(0=all hdmi output)
s cec hdmi out 1
on!
hdmi output 1 power
on
s cec hdmi out y
off!
s cec hdmi out y
mute!
set hdmi output y power off by
s cec hdmi out 1
CEC, y=0~4(0=all hdmi output)
off!
set hdmi output y volume mute by s cec hdmi out 1
CEC, y=0~4(0=all hdmi output) mute!
hdmi output 1 power
off
hdmi output 1 volume
mute
s cec hdmi out y
vol-!
set hdmi output y volume down
by CEC, y=0~4(0=all output)
s cec hdmi out 1
vol-!
s cec hdmi out y
vol+!
set hdmi output y volume up by
CEC, y=0~4(0=all output)
s cec hdmi out 1
vol+!
hdmi output 1 volume
down
hdmi output 1 volume
up
s cec hdmi out y
active!
set hdmi output y active source
by CEC, y=0~4(0=all output)
s cec hdmi out 1
active!
hdmi output 1 active
source
r ipconfig!
IP Mode: Static
IP: 192.168.1.72
Subnet Mask:
255.255.255.0
Gateway: 192.168.1.1
TCP/IP port=8000
Telnet port=10
Mac address:
00:1C:91:03:80:01
Network Setting
r ipconfig!
Get the Current IP Configuration
- 19 / 21 -
Default Setting
Command Code
Function Description
Example
Feedback
r mac addr!
Mac address:
00:1C:91:03:80:01
s ip mode z!
Set network IP mode to static IP
or DHCP,
z=0~1 (z=0 Static, z=1 DHCP )
s ip mode 0!
Set IP mode:Static
(Please use "s net
reboot!" command or
repower device to
apply new config!)
r ip mode!
Get network IP mode
r ip mode!
s ip addr
xxx.xxx.xxx.xxx!
Set network IP address
s ip addr
192.168.1.100!
r ip addr!
Get network IP address
r ip addr!
r mac addr!
Get network MAC address
s subnet
xxx.xxx.xxx.xxx!
Set network subnet mask
s subnet
255.255.255.0!
r subnet!
Get network subnet mask
r subnet!
s gateway
xxx.xxx.xxx.xxx!
Set network gateway
s gateway
192.168.1.1!
r gateway!
Get network gateway
r gateway!
s tcp/ip port x!
r tcp/ip port!
s telnet port x!
r telnet port!
s net reboot!
Set network TCP/IP port
(x=1~65535)
Get network TCP/IP port
Set network telnet port
(x=1~65535)
Get network telnet port
Reboot network modules
IP Mode: Static
Set IP address:
192.168.1.100 (Please
use "s net reboot!"
command or repower
device to apply new
config!)
DHCP on, Device can't
config static address,
set DHCP off first.
IP:192.168.1.100
Set subnet Mask
address:255.255.255.0
(Please use "s net
reboot!" command or
repower device to
apply new config!)
DHCP on, Device can't
config subnet mask,
set DHCP off first.
Subnet Mask:
255.255.255.0
Set gateway:
192.168.1.1
Please use "s net
reboot!" command or
repower device to
apply new config!
DHCP on, Device can't
config gateway, set
DHCP off first.
Gateway:192.168.1.1
s tcp/ip port 8000! Set TCP/IP port:8000
r tcp/ip port!
TCP/IP port:8000
s telnet port 23!
Set Telnet port:23
r telnet port!
Telnet port:23
s net reboot!
Network reboot…
IP Mode: Static
IP: 192.168.1.72
Subnet Mask:
255.255.255.0
Gateway: 192.168.1.1
TCP/IP port=8000
Telnet port=10
Mac address:
00:1C:91:03:80:01
- 20 / 21 -
Default Setting
11. Application Example
PC
OUTPUT 1
RS-232
TX
TCP/IP
OUT
HDMI
OUTPUT 3
OUTPUT 2
RJ45
RX
RJ45
1
IR
2
HDMI
OUTPUT 4
OUT
RJ45
1
2
HDMI IN
3
4
HDMI
RJ45
3
IR
4
HDMI
DC 12V
LAN
TV
HDMI OUT
Power Supply
CAT6
IR Blaster
CAT IN
SERVICE IR IN
DC 12V
TV box
LAN
PC
Receiver
DVD or Blu-ray Player
IR Receiver
x4
TV
The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
- 21 / 21 -
">