Broan-NuTone BELS8 Roomside Series Humidity Sensing Bathroom Exhaust Fan Installation Guide
Broan-NuTone BELS8 is a humidity sensing fan/light combo designed to improve indoor air quality by automatically turning on when humidity levels reach a certain threshold. It features a timer, adjustable humidity settings, manual operation, and a variety of mounting options. This makes it suitable for bathrooms, kitchens, or other areas where humidity control is important.
PDF
Download
Document
Advertisement
Advertisement
BELS8 Roomside Series Humidity Sensing Fan/Light READ AND SAVE THESE INSTRUCTIONS WARNING For Warranty Statement, Service Parts, Technical Support, or to Register your product, please visit our website or call: In the United States - Broan-NuTone.com 800-558-1711. In Canada - Broan-NuTone.ca 800-567-3855. TO CLEAN THE SENSOR: Remove the grille and grille trim. Use a dry dustcloth, clean toothbrush or lightly vacuum to clean sensor and grille. DO NOT USE ABRASIVE CLOTH, STEEL WOOL PADS OR SCOURING POWDERS. DO NOT USE cleaning sprays, solvents or water on or near sensor! The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or unusual noises, replace the blower assembly (includes motor and impeller). TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards. 4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. 5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 6. Ducted fans must always be vented to the outdoors. 7. Acceptable for use over a tub or shower when connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit (ceiling installation only). 8. This unit must be grounded. 9. Do not use this fan with any solid-state speed control device. 10. Do not use replacement parts that have not been recommended by Broan NuTone LLC. 11. If the fan makes excessive noise or if there is unusual noise or smells of smoke. Disconnect power supply and contact customer service. 12. The wearing of safety glasses and gloves is recommended when installing, maintaining or cleaning the unit to reduce the risk of injury that could be caused by the presence of thin metal and/or moving parts. OPERATION Use an on/off switch to operate the fan, light and sensor. The fan, light and sensor can be operated separately if an appropriate 3-function wall control is used. Refer to Broan-NuTone catalog for a complete line of accessories/ controls to effectively adapt these fans to your requirements. SENSOR OPERATION To activate the humidity sensor, turn the humidity switch ON. The fan will run automatically when the set Humidity condition is met, and stop automatically when the timer condition is met. The Humidity Sensor may occasionally turn the fan ON when environmental conditions change. 70 60 80 20 90 10 50 100 OFF 0 % HUMIDITY CAUTION 1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 2. Install the fan at least 8 feet (2.4 m) above the floor. 3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 4. DO NOT TOUCH THE HUMIDITY-SENSING CIRCUIT BOARD. Electrostatic discharge may damage the circuit board. 5. Please read specification label on product for further information and requirements. CLEANING & MAINTENANCE TO CLEAN THE GRILLE: Remove the grille and grille trim. Plastic parts can be cleaned with mild detergent, such as dishwashing liquid. Dry with a soft cloth. DO NOT USE ABRASIVE CLOTH, STEEL WOOL PADS OR SCOURING POWDERS. TO CLEAN INTERIOR OF THE UNIT: Once the grille and grille trim are removed, gently vacuum interior of the unit with the dusting brush attachment. 1 30 40 50 60 TIME % HUMIDITY ADJUSTMENT To adjust the % HUMIDITY: 1. Turn power off at electrical service panel. 2. Use a small screwdriver to carefully rotate %HUMIDITY control to desired level. If fan is not responding to changing humidity conditions, adjust towards 50%. If fan is responding too often to changing humidity conditions, adjust towards 100%. 3. Turn power on. 4. Repeat above steps if necessary. MINUTES ADJUSTMENT (TIMER) This humidity-sensing fan has a timer that controls how long the fan remains on after the humidity in the room returns to the useradjustable set-point. To adjust the timer: 1. Disconnect power at electrical service panel. 2. Use a small screwdriver to carefully rotate MINUTES control to increase or decrease time. 3. Turn power on. 4. Repeat above steps if necessary. If fan is still not responding as desired after making adjustments, contact Broan Technical Support. MANUAL ON To manually energize the fan: - Turn the fan only switch on or - Cycle the Humidity switch on/off/on. ROOF CAP* (with built-in damper) COOKING AREA Do not install above or inside this area. INSULATION (Place around and over fan housing.) FAN HOUSING 45o NOT FOR USE IN A COOKING AREA. POWER CABLE * 45o Keep duct runs short. Seal gaps around housing. Cooking Equipment 4-IN. ROUND DUCT* Floor OR Seal duct joints with tape. * Purchase separately. IMPORTANT - The ducting from this fan to the outside of the building has a strong effect on the air flow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended. Insulation around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their rated airflow. WALL CAP* (with built-in damper) 4-IN. ROUND ELBOWS* OPTION - To mount housing anywhere between ceiling framing: Use optional Hanger Bar Kit (sold separately from local distributors or website). Follow mounting instructions included with kit. QUICK START GUIDE 11 Remove from packaging. Remove blower assembly and wiring panel. Scan this QR code for Installation video. WIRING PANEL SENSOR 21 BLOWER ASSEMBLY Mount housing. Choose one option to mount housing to ceiling structure: Note: If you are installing retrofit, bend New Construction HOUSING Retrofit the ears in and use the mask from packaging to cut opening to correct size. MOUNTING EAR I-JOIST WOOD BLOCKING Use this mask to prevent construction dust, drywall spray, or paint from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE. Utiliser ce couvercle pour empêcher la poussière de construction, le plâtre ou la peinture d'endommager l'intérieur du produit. ENLEVER LE COUVERCLE AVANT D'INSTALLER LA GRILLE. Utilice esta cubierta para prevenir daños al interior del producto debidos a polvo de construcción, rociado en el panel de yeso o pintura. RETIRE LA CUBIERTA ANTES DE INSTALAR LA REJILLA (IF REQUIRED) or Other options: - Hanger bars (sold separately Model Number MHB4) - Flange Install (see Installation video) 2 Choose one option to attach duct connector. 31 New Construction Retrofit Install duct connector (use screw from parts bag and ensure tabs engage in housing), then attach new construction ductwork with foil tape. Pull ductwork into housing and attach to duct connector with foil tape, then install duct connector (use screw from parts bag and ensure tabs engage in housing). FOIL TAPE TABS or FOIL TAPE TABS Pro Tip: First and last 18" of the ducting should be rigid or stretched straight for expected performance. Connect wiring. 41 Scan this QR code for helpful hints. WIRING OPTION # 1 • When first switch (1) is ON, fan will operate automatically based on room humidity conditions. • Turn fan ON immediately for the set timer period (to control odors), by cycling first switch (1) ON/OFF/ON. • Use second switch (2) to turn light ON/OFF. • With optional connection shown, fan will always be ON when light is ON. WIRING OPTION # 2 • When first switch (1) is ON, fan will operate automatically based on room humidity conditions. • Turn fan ON immediately (to control odors), by using second switch (2). • Use third switch (3) to turn light ON/OFF. 3-FUNCTION CONTROL (PURCHASE SEPARATELY) 2-FUNCTION CONTROL (PURCHASE SEPARATELY) (2) BLK RED LIGHT (ON/OFF) (3) (2) (Optional) COM (1) FAN (AUTO/OFF) GRD GREY BLK BLK 120 BLK VAC GRD LINE IN WHT WHT GRD WHT SWITCH WHT UNIT BLK 61 3 RED GREY BRN BLK 120 VAC WHT LINE GRD IN Attach wire enclosure by tab and screw. WHT WHT (1) BLK HUMIDITY CONTROL WHT FAN WHT WHT WHT GRD SWITCH 51 LIGHT RED FAN AUTO (AUTO/OFF) WHT BLK COM FAN (ON/OFF) FAN WHT BRN HUMIDITY CONTROL BLK LIGHT (ON/OFF) LIGHT UNIT Re-install wiring panel and secure with screw from parts bag. 71 Install the blower assembly and sensor with provided screws. Plug in blower. Plug in sensor. Note: For new construction, use mask to protect blower until ceiling is finished. MOTOR PLUG LED MODULE PLUG SENSOR PLUG SENSOR 81 Use this mask to prevent construction dust, drywall spray, or paint from damaging inside of product. Install the grille trim with screws from parts bag. REMOVE MASK BEFORE INSTALLING GRILLE. Utiliser ce couvercle pour empêcher la poussière de construction, le plâtre ou la peinture d'endommager l'intérieur du produit. ENLEVER LE COUVERCLE AVANT D'INSTALLER LA GRILLE. DUCT CONNECTOR HOUSING Utilice esta cubierta para prevenir daños al interior del producto debidos a polvo de construcción, rociado en el panel de yeso o pintura. RETIRE LA CUBIERTA ANTES DE INSTALAR LA REJILLA BLOWER ASSEMBLY WIRING PANEL GRILLE TRIM BELS8 GRILLE LED MODULE 9 Plug in LED module. 1 10 Install the grille by sliding clips into grille trim. Note: Depending upon model, your grille may look different. 4 1115131A Ventilateur avec éclairage de série Roomside BELS8 à détecteur d’humidité LISEZ CES DIRECTIVES ET CONSERVEZ-LES AVERTISSEMENT OBSERVEZ LES DIRECTIVES CI-DESSOUS AFIN DE RÉDUIRE LES RISQUES D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURES CORPORELLES : 1. N’utilisez cet appareil que de la manière prévue par le fabricant. Si vous avez des questions, communiquez avec le fabricant à l’adresse ou au numéro de téléphone indiqués dans la garantie. 2. Avant de procéder à l’entretien ou au nettoyage de l’appareil, coupez l’alimentation du panneau électrique et verrouillez l’interrupteur principal afin d’empêcher que le courant ne soit accidentellement rétabli. S’il est impossible de verrouiller l’interrupteur principal, fixez solidement un message d’avertissement bien visible, par exemple une étiquette, sur le panneau électrique. 3. La pose de l’appareil et les travaux d’électricité doivent être effectués par des personnes qualifiées conformément à la réglementation en vigueur, notamment les normes de la construction ayant trait à la protection contre les incendies. 4. Pour éviter les refoulements, l’apport d’air doit être suffisant pour brûler les gaz produits par les appareils à combustion et les évacuer dans le conduit de fumée (cheminée). Respectez les directives du fabricant de l’appareil de chauffage et les normes de sécurité, notamment celles publiées par la National Fire Protection Association (NFPA), l’American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) et les codes des autorités locales. 5. Veillez à ne pas endommager le câblage électrique ou d’autres équipements non apparents lors de la découpe ou du perçage du mur ou du plafond. 6. Les ventilateurs canalisés doivent toujours rejeter l’air à l’extérieur. 7. Cet appareil peut être installé au-dessus d’une enceinte de baignoire ou de douche s’il est branché sur un circuit de dérivation protégé par un disjoncteur différentiel de fuite à la terre (installation au plafond seulement). 8. Cet appareil doit être relié à une mise à la terre. 9. Ne pas utiliser ce ventilateur avec une commande de vitesse à semi-conducteur. 10. Ne pas utiliser de pièces de rechange non recommandées par Broan NuTone LLC. 11. Si le ventilateur produit un bruit excessif ou s’il y a un bruit, une odeur ou de la fumée inhabituels, débrancher la source d’alimentation et contacter le service à la clientèle. 12. Il est recommandé de porter des lunettes et des gants de sécurité lors de l’installation, de l’entretien ou du nettoyage de cet appareil afin de réduire le risque de blessure causée par la présence d’arête vive et/ou de pièces mobiles. Pour la déclaration de garantie, les pièces de rechange, l’assistance technique ou pour enregistrer votre produit, veuillez visiter notre site Web ou appeler : Aux États-Unis : Broan-NuTone.com 800-558-1711. Au Canada : Broan-NuTone.ca 800-567-3855. NETTOYAGE DU DÉTECTEUR : Enlever la grille et la bordure de la grille. À l’aide d’un chiffon à épousseter, d’une brosse à dents propre ou d’un aspirateur, nettoyer délicatement le détecteur et la grille. NE PAS UTILISER DE CHIFFONS ABRASIFS, DE LAINE D’ACIER NI DE POUDRE À RÉCURER. NE PAS UTILISER de nettoyant en vaporisateur, ni de solvant ni d’eau sur le détecteur ou à proximité! Le moteur est lubrifié en permanence et n’a pas besoin d’être huilé. Si les roulements du moteur sont anormalement bruyants, remplacez l’ensemble de ventilateur (incluant le moteur et la roue à ailettes). FONCTIONNEMENT Utiliser un interrupteur marche/arrêt pour faire fonctionner le ventilateur et le détecteur. Il est possible de faire fonctionner le ventilateur, l’éclairage et le détecteur séparément si une commande murale à trois fonctions est utilisée. Consulter le catalogue Broan-NuTone pour obtenir la ligne d’accessoires/ de commandes complète qui vous permettra d’adapter adéquatement ces ventilateurs selon vos besoins. FONCTIONNEMENT DU DÉTECTEUR Pour activer le détecteur d’humidité, mettre l’interrupteur du détecteur d’humidité en position marche. Le ventilateur fonctionnera automatiquement lorsque le point de consigne sera atteint et s’arrêtera automatiquement à la fin de la minuterie. Le détecteur d’humidité peut à l’occasion mettre le ventilateur en marche lorsque les conditions ambiantes changent. 70 60 80 20 90 10 50 100 OFF 0 % HUMIDITY 30 40 50 60 TIME RÉGLAGE DU % D’HUMIDITÉ Pour ajuster le % D’HUMIDITÉ : 1. Couper le courant au panneau d’alimentation électrique. 2. À l’aide d’un petit tournevis, tourner soigneusement la commande %HUMIDITY au niveau souhaité. Si le ventilateur ne réagit pas aux variations d’humidité, le régler sur 50%. Si le ventilateur réagit trop souvent aux variations d’humidité, le régler sur 100%. 3. Mettre l’alimentation sous tension. 4. Répéter les étapes ci-dessus au besoin. RÉGLAGE DES MINUTES (MINUTERIE) 1. Pour ventilation générale uniquement. N’utilisez pas cet appareil pour Ce ventilateur à détecteur d’humidité comporte une minuterie qui évacuer des matières ou des vapeurs dangereuses ou explosives. détermine combien de temps le ventilateur reste en marche une fois 2. Installer le ventilateur à au moins 2,4 m (8 pi) au-dessus du plancher. le taux d’humidité revenu au point de consigne réglé par l’utilisateur. 3. Pour éviter d’endommager les roulements du moteur, de déséquilibrer les Pour ajuster la minuterie : pales ou de les rendre bruyantes, débarrassez l’appareil de la poussière de plâtre, de construction, etc. 1. Couper le courant au panneau d’alimentation électrique. 4. NE PAS TOUCHER LA CARTE DE CIRCUIT IMPRIMÉ DE DÉTECTION D’HUMIDITÉ. 2. À l’aide d’un petit tournevis, tourner soigneusement la commande Une décharge électrostatique pourrait endommager le circuit imprimé. MINUTES pour augmenter ou pour diminuer la durée. 5. Veuillez lire l’étiquette de spécifications du produit pour obtenir plus de 3. Mettre l’alimentation sous tension. renseignements, notamment sur les exigences. 4. Répéter les étapes ci-dessus au besoin. Si le ventilateur ne réagit pas tel que souhaité suite aux ajustements, contacter l’assistance technique de Broan. POUR NETTOYER LA GRILLE : Enlever la grille et la bordure de la grille. Les pièces en plastique peuvent être nettoyées avec un détergent doux, tel du MISE EN MARCHE MANUELLE liquide à vaisselle. Sécher à l’aide d’un chiffon doux. NE PAS UTILISER DE Pour actionner manuellement le ventilateur : TISSU ABRASIF, DE TAMPON À RÉCURER OU DE POUDRES À RÉCURER. - Mettre l’interrupteur du ventilateur en position marche POUR NETTOYER L’INTÉRIEUR DE L’APPAREIL : Une fois la grille et la ou bordure de la grille enlevées, nettoyez l’intérieur de l’appareil avec un - Effectuer un cycle avec l’interrupteur du détecteur d’humidité aspirateur muni d’une brosse à épousseter. 5 (marche/arrêt/marche). ATTENTION NETTOYAGE ET ENTRETIEN CAPUCHON DE TOIT* (avec clapet intégré) ZONE DE CUISSON Ne pas installer au-dessus ou à l’intérieur de cette zone. ISOLANT (Le placer sur le boîtier du ventilateur et autour.) BOÎTIER DU VENTILATEUR CÂBLE D’ALIMENTATION * 45o NE PAS INSTALLER DANS UNE ZONE DE CUISSON. 45o Utilisez des conduits les plus courts possible. Scellez l’écart autour du boîtier. Appareil de cuisson 10 CM (4 PO) CONDUIT ROND* Scellez les joints avec du ruban à conduit. Plancher * Vendu séparément. IMPORTANT - Les conduits allant de ce ventilateur jusqu’à l’extérieur de l’habitation ont une grande influence sur le débit d’air, le bruit du ventilateur et sa consommation d’énergie. Pour obtenir le meilleur rendement, utilisez les conduits les plus courts et les plus droits possible et évitez d’utiliser des conduits plus petits que ceux recommandés. L’isolation des conduits peut contribuer à réduire les pertes d’énergie et éviter la prolifération de moisissures. Les ventilateurs installés sur d’anciens conduits pourraient ne pas produire leur débit d’air nominal. OU CAPUCHON MURAL* (avec clapet intégré) 10 CM (4 PO) COUDES RONDS* OPTION - Pour installer le boîtier n’importe où entre les solives du plafond : Utilisez l’ensemble de barres de suspension offert en option (vendu séparément chez votre distributeur local ou site Web). Suivez les instructions accompagnant l’ensemble. GUIDE DE DÉMARRAGE RAPIDE 11 Déballer. Enlever l’assemblage du ventilateur et le panneau du câblage. Balayer ce code QR pour accéder à une vidéo d’installation. PANNEAU DU CÂBLAGE DÉTECTEUR 21 ASSEMBLAGE DU VENTILATEUR Installer le boîtier. Choisir une option pour installer le boîtier à la charpente du plafond : Nouvelle construction BOÎTIER Rénovation BRIDE DE MONTAGE I-JOIST EN «I» SOLIVE WOOD BLOC DE BOIS BLOCKING Note : S’il s’agit d’une installation pour rénovation, plier les brides vers l’intérieur et utiliser le masque qui fait partie de l’emballage pour découper l’ouverture à la bonne dimension. Use this mask to prevent construction dust, drywall spray, or paint from damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE. Utiliser ce couvercle pour empêcher la poussière de construction, le plâtre ou la peinture d'endommager l'intérieur du produit. ENLEVER LE COUVERCLE AVANT D'INSTALLER LA GRILLE. Utilice esta cubierta para prevenir daños al interior del producto debidos a polvo de construcción, rociado en el panel de yeso o pintura. RETIRE LA CUBIERTA ANTES DE INSTALAR LA REJILLA (SI REQUIS) ou Autres options : - Support de montage (vendu séparément numéro de modèle MHB4) - Installation sur bride (voir la vidéo d’installation) 6 Choisir une option pour raccorder le connecteur de conduit. 31 Nouvelle construction Rénovation Tirer le conduit dans le boîtier et raccorder au connecteur de conduit avec du ruban d’aluminium, puis installer le connecteur de conduit (utiliser la vis dans le sac de pièces et s’assurer que les ergots s’engagent dans le boîtier). Installer le connecteur de conduit (utiliser la vis dans le sac de pièces et s’assurer que les ergots s’engagent dans le boîtier), puis raccorder le conduit de la nouvelle construction avec du ruban d’aluminium. RUBAN D’ALUMINIUM ERGOTS ou RUBAN D’ALUMINIUM ERGOTS Conseil : La première et la dernière section de 18 po de conduit doit être rigide ou étirée pour obtenir le rendement attendu. Balayer ce code QR 41 Effectuer les branchements. pour des conseils. OPTION DE BRANCHEMENT # 1 • Lorsque le premier commutateur (1) est en position marche, le ventilateur fonctionne automatiquement en fonction des conditions d’humidité ambiante. • Mettre immédiatement le ventilateur en marche pendant la période programmée (pour contrôler les odeurs) en effectuant un cycle avec le premier commutateur (marche/arrêt/marche). • Utiliser le deuxième commutateur (2) pour allumer/éteindre l’éclairage. • Avec le branchement optionnel illustré, le ventilateur sera toujours en marche lorsque l’éclairage est allumé. OPTION DE BRANCHEMENT # 2 • Lorsque le premier commutateur (1) est en position marche, le ventilateur fonctionne automatiquement en fonction des conditions d’humidité ambiante. • Mettre immédiatement le ventilateur en marche (pour contrôler les odeurs) en utilisant le deuxième commutateur (2). • Utiliser le troisième commutateur (3) pour allumer/éteindre l’éclairage. COMMANDE À 2 FONCTIONS (VENDUE SÉPARÉMENT) COMMANDE À 2 FONCTIONS (VENDUE SÉPARÉMENT) (2) (3) NOIR ROUGE ÉCLAIRAGE (ALLUMÉ/ÉTEINT) ÉCLAIRAGE (ALLUMÉ/ ÉTEINT) ÉCLAIRAGE (2) (en option) COM GRIS (1) FIL DE TERRE VENTILATEUR (MARCHE/ARRÊT) NOIR ENTRÉE 120 FIL DE TERRE Vca BLANC INTERRUPTEUR 51 NOIR FIL DE TERRE NOIR VENT. BLANC (1) NOIR VENT. AUTO (AUTO/ARRÊT) BRUN CONTRÔLE D’HUMIDITÉ BLANC GRIS NOIR ROUGE BLANC VENT. BLANC BRUN NOIR ENTRÉE BLANC 120 Vca FIL DE TERRE BLANC BLANC BLANC ÉCLAIRAGE ROUGE VENT. MARCHE/ ARRÊT) BLANC NOIR NOIR COM APPAREIL Fixer le boîtier du câblage avec l’ergot et la vis. 6 1 7 INTERRUPTEUR CONTRÔLE D’HUMIDITÉ BLANC BLANC BLANC FIL DE TERRE APPAREIL Réinstaller le panneau du câblage et le fixer avec la vis dans le sac de pièces. 71 Installer l’assemblage du ventilateur et le détecteur à l’aide des vis fournies. Brancher le ventilateur. Brancher le détecteur. Note : Dans le cas d’une nouvelle construction, utiliser le masque pour protéger le ventilateur jusqu’à ce que le plafond soit fini. PRISE MOTEUR PRISE MODULE DEL PRISE DÉTECTEUR DÉTECTEUR 81 Use this mask to prevent construction dust, drywall spray, Installer la bordure de la grille à l’aide des visfrom dans le sac de pièces. or paint damaging inside of product. REMOVE MASK BEFORE INSTALLING GRILLE. CONNECTEUR DE CONDUIT Utiliser ce couvercle pour empêcher la poussière de construction, le plâtre ou la peinture d'endommager l'intérieur du produit. ENLEVER LE COUVERCLE AVANT D'INSTALLER LA GRILLE. BOÎTIER Utilice esta cubierta para prevenir daños al interior del producto debidos a polvo de construcción, rociado en el panel de yeso o pintura. RETIRE LA CUBIERTA ANTES DE INSTALAR LA REJILLA ASSEMBLAGE DU VENTILATEUR PANNEAU DU CÂBLAGE BORDURE DE LA GRILLE GRILLE BELS8 MODULE DEL 91 Brancher le module DEL. 1 10 Installer la grille en glissant les clips dans la bordure de la grille. Note : La grille peut différer selon le modèle. 8 1115131A ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Humidity Sensing
- Timer
- Adjustable Humidity Settings
- Manual Operation
- Light fixture
- Quiet Operation
- Energy Efficient
- Easy Installation
- GFCI Protected
- Durable Construction
Frequently asked questions
Turn the power off at the electrical panel. Use a small screwdriver to rotate the %HUMIDITY control to the desired level. If the fan is not responding to humidity changes, adjust towards 50%. If it's responding too often, adjust toward 100%. Turn the power back on.
You can manually turn the fan on by either turning the fan-only switch on or by cycling the humidity switch on/off/on.
The timer controls how long the fan remains on after the humidity in the room has returned to the set-point. You can adjust the timer duration with a small screwdriver.