Ask Proxima | DLP Projector | User`s guide | Ask Proxima DLP Projector User`s guide

>>>>>>>
InFocus Corporation
27700B SW Parkway Avenue
Wilsonville, Oregon 97070-9215
1-800-294-6400 • 503-685-8888
Fax: 503-685-8887
http://www.infocus.com
In Europe:
InFocus International B.V.
Strawinskylaan 585
1077 XX Amsterdam,The Netherlands
Phone: +31 20 579 2000
Fax: +31 20 579 2999
In Asia:
InFocus Systems Asia Pte Ltd.
238A Thomson Road
#18-01/04 Novena Square
Singapore 307684
Telephone: (65) 6334-9005
Fax: (65) 6333-4525
User’s
Guide
http://www.pureglare.com.au
Declaration of Conformity
FCC Warning
Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon
97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that this projector conform to the following
directives and norms:
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
March, 2005
Trademarks
Canada
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or
registered trademarks of Adobe Systems Incorporated. InFocus, In Focus, and
INFOCUS (stylized), LP, LiteShow, ScreenPlay, LitePort, ASK and Proxima are either
registered trademarks or trademarks of InFocus Corporation in the United States and
other countries.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, CUL, NOM, IRAM, GOST, C-tick
Other specific Country Approvals may apply. Please see product certification label.
InFocus reserves the right to alter product offerings and specifications at any time
without notice.
2
http://www.pureglare.com.au
If you are experienced in setting up projection systems, use the Quick Setup
card that is included with the projector. For complete details on connecting
and operating the projector, refer to this User’s Guide. Electronic versions of
this User’s Guide in multiple languages are available on the included CD.
The most current versions can be found on our website.
Table of Contents
Introduction
Positioning the projector
Projector and Device Connector Guide
Computer connections
Video connections
Connecting a computer source
Required computer connections
Optional computer connections
Displaying a computer source image
Adjusting the image
Using the projector with Windows 98 for the first time
Connecting a video device
Video device connections
Composite video connection
S-video connection
VGA connection
Displaying video
Adjusting the image
Shutting down the projector
Troubleshooting your setup
Using the remote control
Using the audio
Using the keypad buttons
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Using the menus
Picture menu
Settings menu
Maintenance
Cleaning the Lens
Replacing the Projection Lamp
Cleaning the Lamp Housing Screens
Using the security lock
Appendix
Projected Image Size
Red LED Behavior and Projector Errors
5
7
8
8
8
11
11
11
12
13
14
16
17
17
17
18
19
19
21
21
29
30
31
32
32
33
33
34
35
38
41
41
41
43
43
44
44
44
The website also has technical specifications (an interactive image size calculator, laptop activation commands, connector pin outs, a glossary, the
product data sheet), a web store to buy accessories, and a page for online
registration. See the inside back cover for a list of all relevant web addresses.
3
http://www.pureglare.com.au
Important Operating Considerations for Safety
•
Place the projector in a horizontal position no greater than 15 degrees
off axis.
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
•
Use only InFocus-approved ceiling mounts.
•
Use only the power cord provided. A surge-protected power strip is
recommended.
•
Refer to this manual for proper startup and shutdown procedures.
•
In the unlikely event of the lamp rupturing, discard any edible items
placed in the surrounding area and thoroughly clean the area along all
sides of the projector. Wash hands after cleaning the area and handling
the ruptured lamp. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or
federal ordinances and regulations. For more information see
www.eiae.org.
2 ft (
.6m)
Do not place objects or people in the 2 foot (.6m) area along the front of the projector.
For ceiling mount applications, this area should be 5 feet (1.5m).
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty section at
the end of this User's Guide.
5 ft (1.5m)
4
http://www.pureglare.com.au
Introduction
speaker
keypad
Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too. It has native XGA 1024x768
resolution and is compatible with a wide variety of computers and video
devices, including:
•
power cord
connector
power switch
Most standard VCRs, DVD players (progressive and interlaced), progressive DVD, HDTV sources, TV and satellite tuners, camcorders,
video games, and laser disc players.
•
IBM-compatible computers, including laptops, up to 1280x1024 resolution.
•
Apple® Macintosh® and PowerBook® computers up to 1280x1024 resolution.
remote control
receiver (IR)
adjustable foot release
focus (thin ring)
zoom (thick ring)
tethered lens cap
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our website, as specifications are subject to change. Web address information is located on the back inside cover of this User’s Guide.
Accessories
lamp
housing
door
The standard accessories that came with your projector can be found on the
included packing list. Optional accessories are listed in the Accessories catalog that came with the projector and can also found on our website. See the
inside back cover for the Web address.
Online Registration
security lock
Register your projector on our website to receive product updates,
announcements, and registration incentives. See the inside back cover for
the Web address.
connector
panel
adjustable
foot
5
http://www.pureglare.com.au
Connector Panel
The projector provides both computer and video connection options,
including:
•
M1 for computer and video
•
S-video
•
Composite RCA audio/video
RCA
audio/visual
The projector also provides the following connectors:
•
Monitor out
•
Audio out
•
12 volt DC output (see below)
12 volt
DC output
12 volt DC output
+12v
The 3.5mm mini-jack trigger provides a 12 volt DC output. It provides a
constant output while the projector is on. It has numerous uses. For example, if you connect your projection screen to the 12 volt DC output with the
cable that came with your screen, when you turn on the projector the screen
will move down; when you turn the projector off, the screen will return to
the storage position. To use the 12 volt DC output, you must first remove
the safety plug and turn Screen Trigger on in the System menu (see
page 38).
M1computer monitor
out
audio
out
S-video
ground
3.5mm plug
12 volt DC output
connect to, for example, screen relay (see screen
manufacturer for details)
Wireless Projection
You can use the projector’s M1 connector along with the InFocus LiteShow
wireless adapter and software for cable-free digital projection. Contact an
authorized InFocus dealer or visit the website listed on the back inside
cover of this User’s Guide for more information.
6
http://www.pureglare.com.au
Positioning the projector
.5
12
•
•
•
ft.
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector
within 6 inches (.15m) of a wall or other object.
4.8 ft.
Projection angle in 4:3 mode (default)
Position the projector the desired distance from the screen. The distance
from the lens of the projector to the screen, the zoom setting, and the
video format determine the size of the projected image. The top illustration to the right shows three projected image sizes. For more information about image sizes at different distances, see “Projected Image
Size” on page 44.
bottom of image
1.22 ft above center
of lens
•
See “Connecting a video device” on page 16 for additional information
on 16:9 and 4:3 modes.
lens center
10 ft high
image
The image exits the projector at a given angle. This image offset is
112.2% when the projector is in 4:3 mode (default mode). This means
that if you have an image 10’ high, the bottom of the image will be 1.22’
above the center of the lens.
The image offset is 132.9% when the projector is in 16:9 mode. This
means that if you have an image 10’ high, the bottom of the image will
be 3.29’ above the center of the lens.
19 ft.
7.5 ft.
10 ft high
image
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling” on page 38. We recommend
using an InFocus authorized ceiling mount.
•
ft.
•
5
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 6.4 feet (1.95m) from the projection screen.
3. 3
•
ft.
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general guidelines:
Projection angle in 16:9 mode
bottom of image
3.29 ft above center
of lens
7
http://www.pureglare.com.au
lens center
Projector and Device Connector Guide
The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as computers, standard VCRs, DVD players (progressive and interlaced), HDTV sources (1080i, 1035i, and 720p HDTV formats), TV and satellite tuners, camcorders, video games (progressive and interlaced), and laser disc players.
Computer connections
Computer connections involve attaching the VGA and USB ends of the provided computer cable to a computer and connecting the other end (M1) to the
Computer In input on the projector. The USB part of the computer cable allows you to advance slides in a PowerPoint™ presentation via a remote control.
See page 11 for computer/projector setup information.
Video connections
The first step for connecting video is deciding what type of output connector you want to connect to the projector. If there is more than one output on your
video device, select the one with the highest quality. Your options are S-video (higher quality) and Composite video (lesser quality).
If you are connecting the projector to HDTV sources, the projector’s M1 computer connector, labeled Computer In, should be used. Keep in mind that
HDTV and progressive sources should only be handled through the projector’s computer connector. You can also use an M1 to Component adapter (available as an optional accessory) to connect a progressive source’s component connectors to the projector.
audio/visual
(composite)
projector input connectors
12 volt
DC output
computer in
monitor
S-video
(HDTV and
(out)
audio out
progressive
sources)
8
http://www.pureglare.com.au
Video Device
Standard Broadcast TV (not
HDTV) via: cable, digital
cable, satellite TV, DVD, or
VCR
Standard Video Camera
Video
Compatibility
If Your Device
Connector Is
Attach to Adapter
or Labeled
Connector on
Projector
For Setup Instructions, see
Comments
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Composite video
or S-video
Composite video connection on
page 17.
Not for progressive
(i.e. HDTV) sources.
See page 10.
S-video connection on page 17
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Composite video
or S-video
Composite video connection on
page 17.
Not for progressive
(i.e. HDTV) sources.
See page 10.
S-video connection on page 17
Standard Video Game
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Composite video
or S-video
Composite video connection on
page 17.
S-video connection on page 17
9
http://www.pureglare.com.au
Not for progressive
(i.e. HDTV) sources.
See page 10.
Video Device
Video
Compatibility
If Your Device
Connector Is
Attach to Adapter
or Labeled
Connector on
Projector
For Setup Instructions, see
Comments
1080i, 720p
VGA
Computer In
VGA connection on page 18
Not for Component
480i.
Component video
Computer In via
optional M1 to Component adapter
M1 to Component adapter on
page 18
1080i, 720p
VGA
Computer In
VGA connection on page 18
Component 480p
Component video
Computer In via
optional M1 to Component adapter
M1 to Component adapter on
page 18
1080i, 720p
VGA
Computer In
VGA connection on page 18
Component 480p
Component video
Computer In via
optional M1 to Component adapter
M1 to Component adapter on
page 18
HDTV
(High Definition TV)
Progressive DVD
Progressive Video Game
10
http://www.pureglare.com.au
Not for Component
480i.
Not for Component
480i.
Connecting a computer source
connect computer cable
Required computer connections
Connect one end of the provided computer cable (see page 16 for connecting video devices) to the blue M1 Computer In connector on the projector.
Connect the other ends (USB and VESA) to the USB and VGA ports on your
computer. If you are using a desktop computer, you will need to disconnect
the monitor cable from the computer’s video port first (you can connect this
monitor cable to the Monitor Out connector on the projector, see below).
This USB connection allows you to advance slides in a PowerPoint presentation using the remote. USB drivers must be installed to use the USB feature. For more information, see page 15.
connect power cable
Connect the black power cord to the Power connector on the side of the projector and to your electrical outlet.
NOTE: Always use the power cord that shipped with the projector.
Optional computer connections
connect audio cable
To have sound with your presentation, connect an audio cable (optional
cable, not included) to your computer and to the red and/or white Audio In
connectors on the projector.
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.
connect monitor cable
11
http://www.pureglare.com.au
Displaying a computer source image
remove lens cap
Remove the lens cap.
Toggle the Power switch on the side of the projector to the On position.
toggle Power switch
The LED flashes green and the fans start to run. When the lamp comes on,
the start up screen displays and the LED is steady green. It can take a
minute for the image to achieve full brightness.
? No start up screen? Get help on page 21.
Turn on your computer.
turn on computer
The computer’s image should appear on the projection screen. If it doesn’t,
press the Computer button on the projector’s keypad.
If your computer has Windows 98 as its operating system, see “Using the
projector with Windows 98 for the first time” on page 14 regarding the
driver setup process.
Make sure your laptop’s external video port is active.
activate laptop’s external port
monitor key
or LCD/CRT key
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD
key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop’s documentation to learn your laptop’s key combination.
FN key
? No laptop image? Try pressing the Auto Image button on the keypad. Get help on page 22.
12
http://www.pureglare.com.au
Adjusting the image
adjust height
If necessary, adjust the height of the projector by pressing the release button
to extend the foot.
rotate
leveling
foot
If necessary, rotate the leveling foot located at the rear of the projector.
elevator
foot
Avoid placing your hands near the hot exhaust vent in front of the projector.
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
release button
adjust distance
See page 44 for a table listing screen sizes and distances.
Adjust the zoom or focus.
adjust zoom or focus
focus
(thin ring)
If the image is not square, first make sure that the projector is perpendicular
to the screen. If the image is larger or smaller on the top or bottom edge of
the screen, press the top Keystone button to reduce the upper part of the
image, and press the bottom Keystone button to reduce the lower part.
adjust keystone
If the left or right side of the screen is larger or smaller the other, you can
turn the projector to the left or to the right a few degrees to square the
image.
adjust Picture menu
Adjust the Contrast or Brightness in the Picture menu.
See page 35 for help with these menu adjustments.
13
http://www.pureglare.com.au
zoom
(thick ring)
Using the projector with Windows 98 for the first
time
a
The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wizard to load the correct driver (which was installed with your Windows
operating system).
If you are running Windows 2000, Windows ME, or Windows XP, skip these
steps and go to “Adjusting the image” on page 13.
b
a Click Next to begin searching for the driver.
b Make sure “Search for the best driver” is selected, then click Next.
c
c Uncheck any checked boxes, then click Next. Windows automatically
locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.
d
d When Windows finds the driver, you are ready to install it. Click Next.
14
http://www.pureglare.com.au
Skip this page if you did not connect a USB mouse cable
For Windows 98:
•
If you connected the USB cable, the Add New Hardware Wizard
appears again. Drivers must be installed to use the USB functionality.
•
The Wizard launches three times.
The first time it detects a USB Composite Device.
The second time a USB Human Interface Device (for the keyboard).
The third time it detects a USB Human Interface Device (for the
mouse).
For Windows 2000, Windows ME, and Windows XP:
•
The USB drivers are automatically installed.
15
http://www.pureglare.com.au
Connecting a video device
4:3 screen
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. There is also an audio input via the red and white A/V connectors. You can connect the audio directly to the projector to get sound from
the built-in speaker, or you can bypass the projector’s audio system and
connect the audio directly from your source to a stereo or home theater system.
16:9 screen
Do Not Use
4:3
mode
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered
a tuner.
16:9
mode
Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
projector’s Picture Menu. See page 35 for more information.
What is Aspect Ratio?
Aspect ratio is the ratio of the image width to image height. TV screens are
usually 4:3, which is the default for this projector. HDTV and most DVDs
are 16:9. If you’re projecting onto a screen, the size/shape of the screen may
determine which aspect ratio to use. If you are projecting onto a blank wall,
you don’t have the screen size restriction. What you plan to project will also
help you choose between 4:3 and 16:9. Most TV shows are 4:3, while most
movies are 16:9.
Native
mode
(NTSC
only)
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for anamorphic movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies
only appear correctly if the DVD player is set to output to a 16:9 television.
16
http://www.pureglare.com.au
Video device connections
Composite video connection
Plug the provided A/V cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yellow
Video 2 connector on the projector.
connect A/V cable
Plug a white connector into the left audio out connector on the video device
and plug a red connector into the right audio out connector on the video
device. Plug the remaining white connector into the white audio in connector on the projector, and plug the remaining red connector into the red
audio in connector on the projector.
Keep in mind that video output from composite connections is not as high
quality as S-video.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an
S-video cable (available as an optional accessory) into the S-video connector
on your video device and into the S-video connector on the projector. Use
the A/V cable’s red and white audio connectors as described directly above
(the yellow connectors on the A/V cable are not used).
Keep in mind that S-video delivers higher quality video output than composite.
connect S-video and A/V cables
17
http://www.pureglare.com.au
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the M1 computer
end of the cable into the Computer In connector on the projector. Do not
plug the USB end of this cable into the video device.
connect computer and
A/V cables
Use the A/V cable’s red and white audio connectors as described on the
previous page (the yellow connectors on the A/V cable are not used).
M1 to Component adapter
To connect a progressive scan DVD or HD source, use an M1 to Component
adapter (available as an optional accessory). Connect one end of a component cable (not provided) into the adapter. Connect the M1 end of the
adapter into the Computer In connector on the projector.
connect power cable
Connect the power cord to the Power connector on the side of the projector
and to your electrical outlet.
NOTE: Always use the power cord that shipped with the projector.
18
http://www.pureglare.com.au
Displaying video
remove lens cap
Remove the lens cap.
Toggle the Power switch on the side of the projector to the On position.
toggle Power switch
The LED flashes green and the fans start to run. When the lamp comes on,
the start-up screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness.
? No start up screen? Get help on page 22.
Plug in and turn on your video device.
turn on video device
The video device’s image should appear on the projection screen. If it
doesn’t, press the Video button on the keypad.
? No image? Try pressing the Source or Auto Image. Get help on
page 22.
Adjusting the image
adjust height
rotate
leveling
foot
Adjust the height of the projector by pressing the release button to extend
the foot.
Rotate the leveling foot at the rear of the projector, if necessary.
elevator
foot
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
adjust distance
See page 44 for a table listing screen sizes and distances to the screen.
19
http://www.pureglare.com.au
release button
Adjust the zoom and focus.
adjust zoom and focus
focus
(thin ring)
If the image is not square, adjust the keystone using the buttons on the keypad. If the image is not square, first make sure that the projector is perpendicular to the screen. If the image is larger or smaller on the top or bottom
edge of the screen, press the top Keystone button to reduce the upper part
of the image, and press the bottom Keystone button to reduce the lower
part.
adjust keystone
If the left or right side of the screen is larger or smaller the other, you can
turn the projector to the left or to the right a few degrees to square the
image.
adjust volume
Adjust the volume on the keypad or remote.
Adjust the Contrast, Brightness, Color, Tint, or Aspect Ratio in the Picture
menu. See page 35 for help with the menus and these adjustments.
adjust Picture menu options
including Aspect Ratio
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 16.
20
http://www.pureglare.com.au
zoom
(thick ring)
Shutting down the projector
Troubleshooting your setup
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or
keypad button is pressed.
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
The LED on top of the projector indicates the state of the projector and can
help you troubleshoot.
Screen Save
Table 1: LED behavior and meaning
You can make the black screen appear after a preset number of minutes by
turning on the Screen Save feature in the Settings>System menu. See
page 38.
Power Save
The projector also has a Power Save feature that automatically turns the
lamp off after no active sources are detected and no user interaction with
the projector is performed for 20 minutes. By default, this feature is off. See
page 38.
LED color/behavior
Meaning
solid green
The power switch has been toggled on
and the software has initialized or the projector has been powered off via the
remote.
blinking green
The power switch has been toggled on
and the software is initializing, or the projector is powering down and the fans are
running to cool the lamp.
blinking red
A fan or lamp failure has occurred. Make
sure the vents aren’t blocked (see
page 27). Turn off the projector and wait
one minute, then turn the projector on
again. If the projector has been working
exceeded its lamp life (page 41), replace
the lamp and reset the lamp timer. Contact Technical Support if the problem persists.
Turning off the projector
To turn the projector off, press the remote’s Power button to place the projector in the Off state while it is running. When the Power button is pressed
twice (once to start the power-down process and a second time to verify that
you want to power the projector off), the lamp turns off and the LED blinks
green for one (1) minute while the fans continue to run to cool the lamp.
While the LED is blinking green, the projector does not accept any keypad
and remote control input.
see page 44 for more information
When the lamp has cooled, the LED lights solid green and the fans slow
down to minimal speed. To turn off the projector, toggle the power switch to
the off position.
solid red
You can also turn the projector off simply by toggling the power switch to
the off position.
NOTE: Once the projector has been toggled off, you must wait for one (1)
minute before turning the projector on again. This allows the lamp to properly cool. However, if the remote was used to power the projector to the Off
state you do not need to wait one minute to turn it on again.
An unidentifiable error: please contact
Technical Support.
The following tables show common problems. In some cases, more than one
possible solution is provided. Try the solutions in the order they are presented. When the problem is solved, you can skip the additional solutions.
21
http://www.pureglare.com.au
Problem
Solution
Result
no start up screen
plug power cord in projector’s left side
remove lens cap
toggle power switch
correct image
toggle power switch
on side
press the Computer button
activate laptop’s external port
only start up screen appears
A
Startu
p
Scree
n
Start
u
Scre p
en
computer image projected
A
restart laptop
22
http://www.pureglare.com.au
A
no computer image, just the words “Signal out of
range”
A
press the Auto Image button on keypad
computer image projected
adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>Adapter
(location varies by operating system)
Signa
l
rang out of
e
A
A
you may also need to set a different
resolution on your computer, as shown
in the following problem, “image fuzzy
or cropped”
Only my laptop’s background appears, not the
Desktop icons
A
Disable “Extend my Windows Desktop” in
Control Panel>Display>Settings>Display 2
(location varies by operating system)
A
Background and Desktop projected
A
Uncheck this
option, then
click Apply
23
http://www.pureglare.com.au
A
Problem
Solution
Result
image fuzzy or cropped
set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab)
select 1024x768
image clear and not cropped
A
A
A
For a laptop,
disable laptop
monitor
or turn-on dualdisplay mode
move projector, adjust zoom, adjust height
image not centered on screen
correct image
adjust horizontal or
vertical position in
Picture>Advanced
menu
24
http://www.pureglare.com.au
Problem
Solution
Result
image not square
adjust Keystone on keypad
square image
image not sharp
adjust Sharpness (video sources only) in the
Picture>Advanced menu
correct image
AB
AB
image does not fit 4:3 or 16:9 screen
change aspect ratio to 4:3 or 16:9 in
Picture>Aspect ratio menu
25
http://www.pureglare.com.au
correct image
Problem
Solution
Result
image upside down
turn off ceiling in Settings>System menu
correct image
AB
AB
image reversed left to right
turn off rear in Settings>System menu
correct image
A
projected colors don’t match source
AB
adjust color, tint, color temperature,
brightness, contrast in the menus
COLOR
correct image
COLOR
26
http://www.pureglare.com.au
Problem
Solution
Result
The video embedded in my PowerPoint
presentation does not play on the screen
turn off the internal LCD display on your
laptop
Embedded video plays correctly
A
B
A
lamp won’t turn on, LED blinking red
A
B
make sure vents aren’t blocked, turn off the
projector and allow it to cool for one
minute
LED
A
B
lamp turns on
Start
u
Scre p
en
27
http://www.pureglare.com.au
B
Problem
Solution
Result
“Change lamp” message appears at startup or lamp
won’t turn on
lamp must be replaced (see page 41)
lamp turns on
Start
u
Scre p
en
LED
replace lamp
Still need assistance?
If you need assistance, visit our website at www.infocus.com/service or call
us. Check out our HOW TO section there for additional information on
using this projector for home theater or gaming applications. See the inside
of the back cover for support contact information.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
28
http://www.pureglare.com.au
Using the remote control
previous button
next button
The remote uses two (2) provided AA batteries. They are easily installed by
sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.
Caution: When replacing the batteries, be aware that using batteries other
than the type provided with the projector may risk severe damage to the
remote. When disposing of the batteries, be sure to do so in an environmentally proper manner.
navigation
buttons
To operate, point the remote at the projector (not at the computer). The
range of optimum operation is about 15 feet (4.5m).
Pressing the remote’s Power button when the projector’s Power toggle
switch is in the Off position does not cause the projector to power up. You
need to put the projector’s Power toggle switch in the On position to let the
remote power on the projector.
Troubleshooting the remote
•
When the projector is running, you can press the remote’s Power button to
place the projector in the Off state (see page 21 for shutdown info) and
power it off.
Make sure the batteries are installed in the proper orientation and are
not dead.
•
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 34 for more info on the menus.
Make sure you’re pointing the remote at the projector or the screen, not
the computer, and are within the remote range of 15 feet (4.5m). For
best results, point the remote at the projector.
•
If you are trying to advance PowerPoint slides, make sure the USB
cable is connected. If using a USB cable, make sure the correct drivers
are installed.
The remote also has Volume and Mute buttons to control the sound, and
Video and Computer buttons to switch between sources.
Two presentation-specific features are also provided. Use the Blank button
to display a blank screen instead of the current slide (you can choose which
color is displayed, see page 39); use the Effect button to invoke a user-definable action, such as freeze, or change your aspect ratio for viewing DVDs
(see page 39 to learn to program this button).
Previous and Next buttons allow you to navigate through your PowerPoint
presentation while in Slide Show mode. Connect the USB connector on the
provided computer cable to your computer to use these buttons. When you
do this for the first time, the Add New Hardware wizard may appear. See
page 15 for details on loading the correct USB drivers.
29
http://www.pureglare.com.au
Using the audio
connect audio cable
Using the projector’s speakers
To use the projector’s speaker, connect your source to the Audio In connectors (L and/or R) on the projector’s composite connectors.
To adjust the volume, press the Volume buttons on the keypad or remote.
To mute the sound, press the Mute button on the remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
adjust volume
•
Make sure the audio cable is connected.
•
Make sure mute is not active (press the Mute button on the remote).
•
Make sure the volume is turned up enough. Press the Volume button
on the keypad or remote.
•
Make sure the correct source is active.
•
Make sure that you are connected to an “audio out” connector on the
source as opposed to a “line-in” or “microphone” connector.
•
Adjust the audio source.
•
If playing a video, make sure the playback has not been paused.
Connecting external speakers
external speakers
with own power source
The projector can be attached to external amplified speakers by connecting a
3.5mm stereo audio cable from the Audio Out connector on the projector to
the amplified speakers. Alternatively, you can bypass the projector’s audio
system and connect the audio directly from your source to a stereo or home
theater system.
audio out
speaker
cable
30
http://www.pureglare.com.au
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions:
Menu–opens the on-screen menus (page 34).
menu navigation
buttons
Select–confirms choices made in the menus (page 34).
Up/Down arrows–navigates to and adjusts settings in the menus (page 34).
Auto Image–resets the projector to the source.
Presets–cycles through the available preset settings (page 36).
Keystone–adjusts squareness of the image (page 13).
Volume–adjusts sound (page 30).
Video and Computer–changes the active source.
31
http://www.pureglare.com.au
Optimizing computer images
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 34.
Several features are provided to make giving presentations easier. Here is an
overview, details are found in the menu section.
•
The Effect button on the remote allows you to assign various features to
the button. The default effect is About, which displays information
about the projector and current source. You can select among Blank,
Mute, Aspect Ratio, Source, Auto Image, Freeze, and About. See
page 39 for details. The freeze effect allows you to freeze the displayed
image. This is useful if you want to make changes on your computer
without your audience seeing them.
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu (page 37).
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later (page 36).
The Blank button on the remote allows you to display a blank screen
instead of the active source. You can determine the color of this screen
(page 39).
•
The Startup Logo option lets you change the default start up screen to a
blank or default screen (page 39).
•
Two options, Power Save and Screen Save, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life (page 38).
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu
(page 35).
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 35).
•
Adjust the Color Temperature in the Advanced menu (page 37).
•
•
32
http://www.pureglare.com.au
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
information on using the menus, see page 34.
You can customize the projector for your specific setup and needs. See
page 38 to page 40 for details on these features.
•
For rear projection, turn rear mode on in the Settings>System menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu (page 35).
•
For ceiling mounted projection, turn ceiling mode on in the Settings>System menu.
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 35).
•
Specify which source the projector checks first for active video during
power-up.
•
The remote’s Effect button allows you to assign various features to the
button. The default effect is About, which displays information about
the projector and current source. You can select among Blank, Mute,
Aspect Ratio, Source, Auto Image, Freeze, and About. See page 39 for
details.
•
Specify the function of the Effect button on the remote.
•
Turn the projector’s display messages on and off.
•
•
Turn on power saving features.
•
Specify blank screen colors and start up logos.
Select a Sharpness setting (page 37).
•
Specify the language viewed on the menus.
•
Use the Color Control to adjust the color gain (page 37).
•
Save settings for the active source as a preset.
•
Adjust the Color Temperature. Select a listed warmth value (page 37).
•
Turn on Overscan to remove noise on the edges of the image.
33
http://www.pureglare.com.au
Using the menus
keypad navigation
buttons
Main menu
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Previous or Exit, then press Select to
go to the previous menu; press the Menu button at any time to close the
menus.
Settings
menu
Picture
menu
Dots appears before the menu name. The number of dots indicate menu’s
level, ranging from one (the Main menu) to four (the most nested menus).
dots
The menus are grouped by usage:
•
The Picture menu provides image adjustments.
•
The Settings menu provides set-up type adjustments that are not
changed often.
•
The About menu provides a read-only display of information about the
projector and source.
Certain menu items may not be visible or may be grayed depending upon a
particular source being connected. For example, Sharpness is only available
for video sources and is not visible when a computer source is active. Menu
options are grayed out only if the source is selected but no signal is present.
For example, if the projector is set to a video source but the source, such as a
DVD player, is turned off video menu options are grayed out.
About menu
34
http://www.pureglare.com.au
Picture menu
Picture menu
To adjust the following settings, highlight the setting, press Select, use the
up and down arrows to adjust the values, then press Select to confirm the
changes.
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
increasing keystone
decreasing keystone
Brightness: changes the intensity of the image.
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: adjusts the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 4:3. HDTV and most DVDs are 16:9. The default is
4:3.
Select Native to see the unmodified input with no resizing by the projector.
Select 16:9 to watch enhanced widescreen DVDs.
For more information regarding Aspect Ratio, see page 16.
Aspect ratio
35
http://www.pureglare.com.au
Presets: Presets are provided that optimize the projector for displaying
computer presentations, photographs, film images, and video images. Film
input is material originally captured on a film camera, like a movie; video
input is material originally captured on a video camera, like a TV show or
sporting event. You can use the preset as a starting point, then further customize the settings for each source. The settings you customize are saved in
the preset for each source. To restore the factory default settings, choose Factory Reset in the Settings>Service menu (page 40).
Presets
Save
User
Settings
There is also a user-definable preset. To set a preset for the current source,
adjust the image, select Save User in the Presets menu, then select Yes. You
can recall these settings in the future by selecting the User 1 preset.
36
http://www.pureglare.com.au
Advanced menu
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Advanced menu
Color Space: This option applies to computer and component video
sources. It allows you to select a color space that has been specifically tuned
for the input signal. When Auto is selected, the projector automatically
determines the standard. To choose a different setting, turn off Auto, then
choose RGB for computer sources, choose either SMPTE240, REC709 or
REC601 for component video sources.
Sharpness
Color Temperature: changes the intensity of the colors. Select a listed relative warmth value.
Color
Space
Color
Temperature
Color Control: allows you to individually adjust the gain (relative warmth
of the color) and the offset (the amount of black in the color) of the red,
green, and blue colors.
Video Standard: when it is set to Auto, the projector attempts to automatically pick the video standard based on the input signal it receives. (The
video standard options may vary depending on your region of the world.) If
the projector is unable to detect the correct standard, the colors may not
look right or the image may appear “torn.” If this happens, manually select
a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Overscan: (video sources only) removes noise around the video image.
Color Control
Sync Threshold Adjust: (progressive signals only) If a hardware device,
such as a DVD player, is not syncing properly with the projector, select this
option to help it to sync when connected to the projector.
The following four (4) options are for progressive and computer sources
only.
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
Video Standard
Horizontal/Vertical Position: adjusts the position of a computer source.
White Peaking: increases the brightness of whites that are near 100%.
37
http://www.pureglare.com.au
Settings menu
Settings menu
Audio: allows adjustments to Volume of the internal speaker and allows a
chime to play when starting the projector. Adjustments can also be made
from the projector’s keypad and the remote.
Audio
Sources: Power-up Source determines which source the projector checks
first for active video during power-up. When the Autosource feature is On,
the projector automatically finds the active source, checking the selected
Power-up Source first. The source options are Computer 1 for a computer,
progressive DVD, or HDTV source, and Video 1 (for S-video connections),
and Video 2 (for composite video connections) for video sources. When this
feature is Off, the projector defaults to the source selected in Power-up
Source. To display another source, you must manually select one by pressing the Computer or Video button on the remote or keypad.
Sources
Power-up
Source
System>Rear: reverses the image so you can project from behind a translucent screen. Ceiling: turns the image upside down for ceiling-mounted projection. Low Power: toggles between on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector
quieter. Display Messages: displays status messages (such as “Searching” or
“Mute”) in the lower-left corner of the screen. Screen Saver Off: prevents
your computer from going into Screen Save mode. Screen Trigger turns on
the 12 volt DC output switch on the connector panel. Power Save: automatically turns the lamp off after no signals are detected for 20 minutes. After
10 additional minutes with no signal, the projector powers down. If an
active signal is received before the projector powers down, the image will
be displayed. After an additional 10 minutes with no signal, the projector
powers down and can be toggled off. If an active signal is received before
the projector powers down, the image will be displayed. When Power Save
is enabled, Screen Save is disabled. Screen Save automatically blanks the
screen with a black color after no signals are detected for a preset number of
minutes. The image returns when an active source is detected or a remote or
keypad button is pressed.
System menu
Screen Save
38
http://www.pureglare.com.au
Startup Logo: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
Startup Logo
Blank Screen: determines what color is displayed when you press the
Blank button on the remote.
Blank Screen
Effect Key: allows you to assign a different function to the Effect button on
the remote, allowing you to quickly and easily use the effect. Highlight an
effect and press Select to choose a different one.
•
Blank: displays an empty screen.
•
Mute: turns off all sound.
•
Aspect Ratio: toggles among 4:3, 16:9, and Native (see page 16 and
page 35). Set as the Effect Key, it can allow you to switch the Aspect
Ratio for DVDs.
•
Source: cycles through available sources.
•
Auto Image: resets the projector to the source (page 31).
•
Freeze: pauses the projected image.
•
About: the default effect. It opens a window with projector and source
information.
Effect Key
39
http://www.pureglare.com.au
Language: allows you to select a language for the onscreen display.
Language menu
Service: To use these features, highlight them and press Select.
Service menu
Factory Reset: restores all settings to their default.
Lamp Reset: resets the lamp hours used counter in the About menu to
zero. Do this only after changing the lamp.
Service Code: only used by authorized service personnel.
About: provides information about the projector and the active source.
Showing the About box is the default action assigned to the Effect button.
About menu
40
http://www.pureglare.com.au
Maintenance
Cleaning the Lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
Replacing the Projection Lamp
Lamp hours used
The lamp hours used timer in the About menu counts the number of hours
the lamp has been in use. Twenty hours before the lamp life expires, the
message “Change lamp” appears on the screen at startup.
NOTE: You can order new lamp housings from your dealer. See the Packing
list for information. Use only a replacement lamp with the same type and
rating as the original lamp.
turn off and unplug
projector
wait 30 minutes
1 Turn off the projector and unplug the power cord.
2 Wait 30 minutes to allow the projector to cool thoroughly.
3 Turn the projector on its side so that the lamp door is facing you. Using a
flat-blade screwdriver, gently pry the lamp door from the projector by
placing the screwdriver blade into the space between the top of the lamp
door and the projector.
lamp door
41
http://www.pureglare.com.au
4 Loosen the two captive screws that attach the lamp housing to the projector.
lamp
connector
5 Detach the lamp connector from the projector by depressing the locking
lamp cable
tab on the connector and lightly pulling it free.
WARNING:
To avoid burns, allow the projector to cool for at least 30 minutes
before you replace the lamp.
Do not drop the lamp housing or touch the glass bulb! The glass
may shatter and cause injury.
lamp
housing
Be extremely careful when removing the lamp housing. In the
unlikely event that the bulb ruptures, small glass fragments may be
generated. The lamp housing is designed to contain these fragments, but use caution when removing the lamp housing. Before
replacing the lamp, clean the lamp compartment and dispose of
cleaning materials. Wash hands after lamp replacement. This product has a lamp which contains a very small amount of mercury. Dispose of it as required by local, state or federal ordinances and
regulations. For more information see www.eiae.org.
captive screw
connector
6 Carefully remove the lamp housing. Dispose of the lamp in an environ-
lamp cable
locking tab
mentally proper manner.
7 Install the new lamp housing and tighten the screws.
lamp
housing
8 Re-attach the lamp connector to the projector. The locking tab should
captive screw
engage when the connector is fully plugged in.
9 Replace the lamp door.
10 Plug in the power cord and toggle the Power switch to turn the projector
back on.
11 To reset the lamp hour timer, navigate to the Settings>Service menu
Service menu
and select Lamp Reset. See page 40 for details. Or, simultaneously press
both Volume buttons on the keypad and hold them for 10 seconds.
42
http://www.pureglare.com.au
Cleaning the Lamp Housing Screens
In dirty or dusty environments, the two dust filter screens in the lamp housing can become clogged, causing high temperatures and premature lamp
failure. Routine maintenance to remove dust from the screens lowers the
lamp operating temperature and prolongs lamp life. To maximize lamp life
you should clean the screen every 250 hours.
lamp housing
lamp
1 Remove the lamp housing.
two screens
(one on each
side of the
lamp housing)
2 Examine the dust filter screens on the lamp housing. If necessary, use a
vacuum cleaner set on low power to clean the screens. Be careful not to
disturb any internal components when cleaning the screens.
3 Replace the lamp housing and lamp door.
Using the security lock
The projector has a security lock for use with a PC Guardian Cable Lock
System. Refer to the information that came with the lock for instructions on
how to use it.
security
lock
43
http://www.pureglare.com.au
Appendix
Red LED Behavior and Projector Errors
Projected Image Size
If the projector is not functioning properly and the LED is blinking red, consult Table 3 to determine a possible cause. There are two-second pauses
between the blinking cycles. Visit our website for more details on the red
LED error codes.
NOTE: Visit our website for an interactive image size calculator.
Table 3: LEDs
Table 2:
Range of distance to the screen for a given screen size for the
projector
Red LED Behavior
Explanation
One (1) blink
The lamp won't strike after five (5)
attempts. Check the lamp and lamp door
installations for loose connections.
Three (3) blinks
The projector has shut down. Check to
see if the lamp door is open. If the lamp
door is closed, toggle off the projector
and wait one minute, then toggle the projector on again. If the lamp does not strike
after one minute, replace the lamp. Contact Technical Support (see page 28) for
repair if replacing the lamp does not solve
the problem.
Four (4) blinks
The fan has failed. Contact Technical Support (see page 28) for repair.
Five (5) blinks
The projector is overheating. Check for a
blocked air vent or clogged lamp housing
screen (previous page). Contact Technical
Support for repair if clearing the vents/
screens does not solve the problem.
Distance to screen
Diagonal
Screen Size
(inches/m)
50/1.3
60/1.5
100/2.5
150/3.8
200/5.1
Image Width
(inches/m)
40/1
48/1.2
80/2
120/3.1
160/4.1
Maximum
distance
(feet/m)
7.8/2.4
8.8/2.7
14.6/4.5
22.6/6.9
30.5/9.3
Minimum
Distance
(feet/m)
6,5/2.0
7.5/2.3
12.4/3.8
19.03/5.8
25.2/7.7
44
http://www.pureglare.com.au
C
cable box 16
Color 35
Color Control 37
Color Space 37
Color Temperature 37
compatibility
IBM-compatible 5
Macintosh 5
video devices 5
Computer In connector 11
connecting
video device 16
connector panel 6
connectors on projector 9, 10
contacting InFocus 28
Contrast 35
customer service contact information 28
customizing the projector 33
D
Display Messages 38
Drivers
USB 15
Windows 98 15
DVDs 35
E
Effect button 32, 33
Effect Key 39
F
Factory Reset 40
focus 13, 20
INDEX
Numerics
16x9 vs 4x3 screen aspect 16
A
About 39, 40
Advance menu 37
advancing slides 11
Aspect Ratio 39
Aspect ratio 35
aspect ratio 16
Audio 38
Audio In connector 11, 17, 30
audio input 16
Audio Out 16
Autosource 38
B
Blank button 32
Blank Screen 39
blinking green 21
blinking red 21
Brightness 35
45
http://www.pureglare.com.au
M
M1 to Component adapter 18
Macintosh computers
compatibility 5
maintaining the projector 41
Menu button 34
menu usage 34
Monitor Out connector 11
Mute button 30
O
optimizing images 32
optimizing video 33
Overscan 37
P
Phase 37
Picture menu 35
Power connector 11
power cord 11, 18
Power Save 21, 38
Power switch 12
Power-up Source 38
presentation
features 32
Presets 36
projection distance 7
projector
connecting video devices 16
connector panel 6
customization 33
keypad buttons 31
maintenance 41
positioning 7
setting up 7
H
HDTV 8, 35
Horizontal 37
I
IBM-compatible computers 5
image
size 7
image optimization 32
image size
projected 44
K
keypad buttons
projector 31
keystone adjustment 13, 20
L
Lamp Housing Screens
cleaning 43
lamp replacement 41
Lamp Reset 40
Language 40
LED 21
blinking green 21
solid green 21
LED Behavior
red 44
LED behavior 21
leveling foot 19
Low Power 38
46
http://www.pureglare.com.au
troubleshooting problems 21
turning off 21
T
Tint 35
Tracking 37
troubleshooting 21
turning off
projector 21
TV tuner 16
U
USB, connecting 11
V
Vertical 37
video optimizing 33
Video Standard 37
volume adjustment 20
Volume button 30
W
warranty 28
Windows 2000 15
Windows 98 14
Windows ME 15
Windows XP 15
Z
zoom 13, 20
R
Rear 38
Red LED behavior 44
registering your projector 5
remote control
advancing slides 11, 29
Effect key 29
laser pointer 29
Previous/Next buttons 29
usage 29
replacing the lamp 41
S
Screen Aspect 16
Screen Save 21, 38
Screen Saver Off 38
Screen Trigger 38
security lock 43
Service 40
Service Code 40
Settings menu 38
sharpness 37
solid green 21
solid red 21
Sources 38
Startup Logo 39
S-video connector 17
Sync Threshhold Adjust 37
System 38
47
http://www.pureglare.com.au
Limited Warranty
•
Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Corporation (“InFocus”) warrants that the Projector, Lamps and Accessories
(hereinafter collectively or individually referred to as “Product” as appropriate) purchased from InFocus, an InFocus distributor, or an InFocus reseller
will conform to InFocus’ specifications and be free from defects in material
or workmanship for the respective Limited Warranty period provided
below. InFocus products are compatible with many systems, however the
specific functional implementation by the customers of the product may
vary. The suitability of a product for a specific purpose or application must
be determined by the customer and is not warranted by InFocus Corporation.
WARRANTY LIMITATION AND EXCLUSION
THIS WARRANTY SETS FORTH INFOCUS’ MAXIMUM LIABILITY FOR
ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PURCHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER.
InFocus shall have no further obligation under the foregoing Limited Warranty if the Product has been damaged due to abuse, improper ventilation,
fire, water, disaster, mispackaging, shipping, lightning or other acts of
nature, misuse, neglect, smoke exposure (cigarette or otherwise), accident,
unusual physical or electrical stress and/or power surges, unauthorized
modifications (including use of an unauthorized mount), tampering, alterations, service other than by InFocus or its authorized agents, or failure
caused other than from ordinary use or failure to properly use the Product in
the application for which said Product was intended. In addition, failure of
the end-user to follow maintenance procedures as outlined in the product’s
user guide where a schedule is specified for regular cleaning of certain parts
(based on usage and environment), will not be covered under this Warranty.
Finally, InFocus shall have no further obligation if the Product was subjected
to operating conditions outside of the range specified in the user’s guide or
in this Warranty. Normal operating conditions are defined as use not in
excess of 16 hours continuously per day with a minimum 8 hour period of
continuous rest in the powered off state. If a claimed defect cannot be identified or reproduced in service, you will be held responsible for the costs
incurred. This Limited Warranty excludes Product cleaning, removal or
installation of the Product, repair, or replacement of plastics due to cosmetic
damage and damage as a result of normal wear. Product repair outside of
the terms of the Limited Warranty will be on a time and materials basis.
InFocus will not be liable for any rental costs incurred in the event of a failure.
If the Product, while subject to this Limited Warranty, is defective in material
or workmanship during the warranty period, then InFocus, at its option, will
REPAIR or REPLACE the Product.
All exchanged parts and Products replaced under this Limited Warranty will
become property of InFocus. InFocus' sole obligation is to supply (or pay for)
all labor necessary to repair the Product found to be defective within the
Limited Warranty period and to repair or replace defective parts with new
parts or, at the option of InFocus, serviceable used parts that are equivalent
or superior to new parts performance. Limited Warranty periods are as follows:
•
Projector Product Limited Warranty Period (Excluding Lamps):
One (1) year from date of proof of purchase.
•
Lamp Product Limited Warranty Periods: The original installed
lamp shall have a ninety (90) day Limited Warranty Period from
date of Projector proof of purchase, and replacement Lamps will
have a ninety (90) day limited warranty from date of lamp proof of
purchase, and replacement lamps purchased at the time of Projector Product purchase will have a ninety (90) day limited warranty
from date of first use.
Accessory Product Limited Warranty Period: ninety (90) days
from date of purchase.
48
http://www.pureglare.com.au
The Warranty does not apply to cartons, carrying cases, shipping cases,
external cabinets, accessories used in connection with the product, or cosmetic parts, knobs, or batteries. The Warranty period for LCD engines is
either 2 years from the date of purchase of the projector or 2500 hours of
projector usage, whichever comes first. If the LCD engine requires replacement and the projector has exceeded 2500 hours, but is otherwise eligible
for Warranty, this Warranty will cover the cost of labor, but not the cost of
parts that require replacement.
Limited Warranty Period
The Limited Warranty periods hereof commence on the date of proof of purchase by the end-user customer. These Limited Warranty provisions shall
apply only to the end-user purchaser (first person or entity that purchased a
new Product for personal or business use and not for the purpose of distribution or resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER
RIGHTS WITH MINIMUM WARRANTY DURATION THAT DIFFER
FROM THE DURATIONS PROVIDED HEREIN, AND INFOCUS WILL
HONOR ALL SUCH CONSUMER RIGHTS UPON PROOF OF PURCHASE
IN THAT JURISDICTION.
The Accessory Product Limited Warranty covers the accessory item only
and excludes normal wear. The Lamp Product Limited Warranty excludes
expected lamp degradation and InFocus will not be liable for normal
decrease in lamp output over time or as lamp is consumed under the Limited Warranty.
To Be Eligible For Limited Warranty Coverage
Any person exercising a claim under this Limited Warranty must establish
to the satisfaction of InFocus both the date of purchase and that the Product
was purchased new. The sales receipt or invoice, showing the date of purchase of the Product is the proof of the date of purchase.
Remanufactured Products and Software Products are exempt from the foregoing Limited Warranty. Please refer to the appropriate Remanufactured
Product Limited Warranty or Software Product Limited Warranty for applicable Warranty information.
To Obtain Warranty Service
During the Limited Warranty period, to exercise this Limited Warranty, the
purchaser must first contact 1) InFocus, 2) a service facility authorized by
InFocus or 3) the place of original purchase.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR
PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND
THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED
OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS.
SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS
MAY NOT APPLY TO YOU.
InFocus Customer Service in the Americas 1-800-799-9911 or 503-685-8888
or www.infocus.com/service, In Europe, Middle East, and Africa +31 (0) 20
579 2820, and in Asia Pacific +65 6353 9449.
For Warranty service, the purchaser will pay to return or deliver the defective Product and will pay all freight, duty, taxes, VAT, fees, incidental clearance and customs charges to ship the unit to an InFocus Service Center or to
a service facility authorized by InFocus. When returning Product to InFocus, a Return Material Authorization Number (RMA #) is required and
must be clearly displayed on the outside of the shipping carton or a similar
package affording an equal degree of protection.
49
http://www.pureglare.com.au
LIMITATION OF LIABILITY
InFocus or the service facility authorized by InFocus will return the
repaired/replaced Product freight prepaid to the purchaser.
IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY SHALL
NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE
PRICE PAID BY PURCHASER Where applicable national law prohibits the
exclusion or limitation of liability, InFocus excludes or limits its liability to
the maximum extent permitted by national law.
Products returned for Warranty service must be accompanied by a written
letter that: (i) explains the problem; (ii) provides proof of date of purchase;
(iii) provides the dealer’s name; and (iv) provides the model and serial
number of the Product. Upon request of InFocus Corporation or an authorized repair center for InFocus, proof of legal import must accompany the
warranty repair Product, otherwise the Product must be returned to the
place of original purchase, to the manufacturer (Purchaser must bear all tax,
duty and freight), or the Purchaser must bear charges for the warranty
repair.
Limitation on Bringing Action - No action, regardless of form, arising out
of the agreement to purchase the Product may be brought by purchaser
more than one year after the cause of action has accrued.
Governing Law - Any action, regardless of form, arising out of the agreement to purchase the Product is governed by the laws of the state of Oregon, USA.
Mandatory Arbitration – Any action, regardless of form, arising out of the
agreement to purchase the Product is subject to mandatory arbitration.
THIS WARRANTY DOES NOT AFFECT YOUR LEGAL RIGHTS UNDER
APPLICABLE NATIONAL LAWS RELATING TO THE SALE OF CONSUMER PRODUCTS.
No repair or replacement of Product or part thereof shall extend the Limited
Warranty period as to the entire Product. Warranty on the repair part and
workmanship shall only be effective for a period of ninety (90) days following the repair or replacement of that part or the remaining period of the
Product Limited Warranty whichever is greater. InFocus’ or its authorized
service center’s policies shall apply and the Consumer will be charged
accordingly for product returned to an InFocus Authorized Service Center
after the expiration of the warranty period.
50
http://www.pureglare.com.au
Download PDF