DIGITAL LED ALARM CLOCK
USER MANUAL
① Some scratches appear on the protective film due to long-distance transportation,please tear
the protective film off before using. (Tips: As our protective film is very thin and fit well, which
requires a little patience to find it and tear off . )
Please feel free to contact us if you have any other problem, we will try our best to solve it.
② Auto Brightness Mode and Night Mode cannot be turned on simultaneously.
③ The supplied battery is only for memorizing the time settings; it just could keep time memory when
power off, couldn't support the digital clock light up.
④ Please remove plastic insulator tab from button battery compartment in the back and connect the
product with electricity by USB or Adapter.
⑤ If time mode is 12 hour mode, when is Afternoon Time, there is “PM” symbol in display, when is
Morning Time, there is no “PM” symbol in display.
① LED Time display (The default time display 0:00).
② There are 3 levels of brightness ( The default setting is the brightest light).
③ Night mode with automatic dimming.
④ Total 4 functional buttons: “M” –Mode button, “+” –Up button, “-”–Down button, “SNOOZE.
⑤ Two kinds of time mode option ( 12/24 hour modes selectable).
⑥ The default Alarm display is 6:00.
⑦ Alarm with Pre-Settable Snooze function ( 5 minutes ).
⑧ Snooze last for 5-60 minutes and unlimited times.
⑨ Power supply: When powered by DC power, the LED is long bright and all functions are normal.
When powered by built-in button cell, the LED light is off and no display, but can keep the time normal
walking and original setting.
⑩ There are 2 USB Output ports on the side (5V, 1A) which allows you to charge Android or Apple
system smart phone in the same time.
Note: Please remove plastic insulator tab from button battery compartment in the back and connect
the product with electricity by USB or Adaptor.
First Press and hold “M” button for more than 3 seconds to start setting time mode. There is“12/24
hours” mode.
Adjust the data using “+” or “-” button. For example, if you choose “24 hours” mode, but “12 hours”
in display, then you can press “+” or “-” to adjust.
After “12/24 hours” mode is setting, you can press “M” once to enter LED Time setting. The
sequence is “Hour”–“Minute. First is “Hour” setting, adjust the data using “+”or“-”button, after “Hour”
setting is done, press “M” to enter “minute” setting.
Remarks:In LED Time setting, there is no “AL” symbol in LED Time display. Adjust the data using
“ + ” or “ - ” buttons, after setting, press “M” once to enter next setting or to confirm. In setup mode, the
setting object is flashing. After setting is done, the setting object is not flashing.
Remarks: Turn on and turn off Alarm: Press " - " to select. For example, when you press “ - ” once,
you can see “AL” symbol in LED Time display and Alarm display. Next you press “-” again, you can see
"AL" symbol only in Alarm display. (There is "AL" symbol both in LED Time display and Alarm display
means Alarm is turn on.
Please check below pictures of LED Time display and Alarm display when Alarm is turn off.
BUZZER alarm last for 2 minutes.
When the alarm beeps, press "SNOOZE" button to enter snooze mode. The corresponding “AL”
symbol flashes till reach to the snooze time set and then alarm again.
When the alarm beeps, press any other buttons except the "SNOOZE" button to turn off the alarm and
snooze. AL symbol stops flashing.
Press and hold "+" button for more than 3 seconds. "OFF" displays which means manual mode. In
manual mode, press the "+" key to select light brightness : bright - medium - dark level by cycle. Press
and hold "+" button for more than 3 seconds. "ON" displays which means auto mode. The default is
auto mode, which means the brightness is changing automatically by the environment, when the
environment is dark, the brightness is low; when the environment is bright, the brightness is high.
After LED Time setting is done, press “M” once to enter Alarm setting, then press and hold “M”
button for more than 3 seconds to make “Hour” – “ Minute”- “Snooze time ”setting.
First Adjust the data using “ + ” or “ - ” buttons to make “hour” setting , then press “M” once to enter
minute setting.
After Alarm is finished, then press “M” to enter snooze time setting. The default Snooze time is 5
minutes, “05” digit is flashing (represents of 5 minutes) . You can press “+” or “ - ” button to set 5-60
minutes snooze time. After snooze time setting is done, press “M” once to confirm.
Night mode means that LED automatically enter into the lowest brightness display status at night.
In LED Time display mode, press “M” button twice to turn on the night mode setting. Select “ON” or
“OFF” by pressing "+" or "-" manually.
The default period of 18:00 to 6:00 the next day, it will automatically enter into lowest brightness
display status. When night mode is “ON”, Press and hold "M" button for more than 3 seconds to enter
interval time setting mode. The setting sequence is:“start hour”–“start minute”- “end hour”–“end
minute”. At start hour and minute setting status, the upper point in the center of the screen is flashing.
At end hour and minute setting status, the lower point in the center of the screen is flashing.
Remarks: Auto Brightness Mode and Night Mode cannot be turned on simultaneously.
If you need to make Night Mode setting, please make sure the dimming setting (Brightness Mode) is
manual. You can choose any time for interval time setting.
">