Canon | CP600 | User guide | Canon CP600 User guide

User Guide
ENGLISH
Guía del usuario
ESPAÑOL
Guide d'utilisation
FRANÇAIS
Connecting the Printer to a Camera and Printing
Conexión de la impresora a la cámara e impresión
Connexion de l'imprimante à l'appareil photo
Connecting the Printer to a Computer and Printing
Conexión de la impresora a un ordenador e impresión
Connexion de l'imprimante à un ordinateur et impression
NOTICE! When a computer is connected to the printer, be sure to install the
software and the printer driver bundled on the supplied CD-ROM (Canon CP
Printer Solution Disk).
If you are using another version of software, actual screen contents and procedures may differ slightly from those indicated in this guide.
¡ATENCIÓN! Cuando se conecte un ordenador a la impresora, asegúrese de
instalar el software y el controlador de la impresora incluidos con el CD-ROM
suministrado (disco CP Printer Solution Disk de Canon).
Si está utilizando otra versión de software, el contenido real de la pantalla y los
procedimientos podrán ser un poco diferentes de los indicados en esta guía.
CDI-M184-010
xx05Nixx
© 2005 CANON INC.
PRINTED IN JAPAN
IMPRIMÉ AU JAPON
ATTENTION ! Quand un ordinateur est connecté à l'imprimante, veillez à
installer le logiciel et le pilote d'imprimante inclus sur le CD-ROM fourni (Canon
CP Printer Solution Disk).
Si vous utilisez une autre version de logiciel, le contenu réel de l'écran et les
procédures peuvent être légèrement différents de ceux indiqués dans ce guide.
When used with the EOS 10D, EOS 20D, or EOS DIGITAL REBEL
Be sure to set [Communication] in the camera's menu to [PTP] before
connecting the camera to this printer. If you set [Communication] to [Normal],
printing is not available (refer to the camera's User Guide for the menu
settings).
Cuando se utilice con la EOS 10D, EOS 20D o EOS DIGITAL REBEL
Asegúrese de poner [Comunicación] en el menú de la cámara en [PTP] antes
de conectar la cámara a esta impresora. Si pone [Comunicación] en
[Normal], la impresión no se encontrará disponible (consulte la Guía del
usuario de la cámara para conocer la configuración del menú).
Lors de l'utilisation avec un appareil EOS 10D, EOS 20D ou EOS
DIGITAL REBEL
Avant de connecter l'appareil à cette imprimante, veillez à régler
[Communication] sur [PTP] dans le menu de l'appareil. Si vous réglez
[Communication] sur [Normal], l'impression n'est pas disponible (pour les
réglages du menu, reportez-vous au Guide d'utilisation de l'appareil).
English
Contents
Enjoy Various Kinds of Printing...................................................................2
Printing Procedure and Reference Guides .................................................4
Package Contents..........................................................................................6
Quick Start......................................................................................................8
Before You Begin.........................................................................................12
What Can Be Accomplished with this Printer...........................................13
Symbols Used ......................................................................................................... 13
Read This First.............................................................................................14
Safety Precautions .................................................................................................. 14
Proper Usage and Handling.................................................................................... 18
Components Guide ................................................................................................. 22
Let’s Print .....................................................................................................23
Preparing Your Ink Cassette/Paper Sets and Paper Cassette ............................... 23
Loading the Ink Cassette ........................................................................................ 25
Placing the Paper into the Paper Cassette ............................................................. 26
Loading the Paper Cassette.................................................................................... 28
Connecting a Power Source and the Camera to the Printer ................................... 29
Printing .................................................................................................................... 31
Battery Usage...............................................................................................35
Using the Battery Pack............................................................................................ 35
Troubleshooting ..........................................................................................39
Error Messages............................................................................................42
Specifications ..............................................................................................44
Connecting the Printer to a Computer and Printing.................................46
Read Carefully Before Using!.................................................................................. 46
System Requirements............................................................................................. 48
Printing Operations Overview ................................................................................. 49
Installing the Software and the Printer Driver.......................................................... 50
Windows ............................................................................................................ 50
Macintosh .......................................................................................................... 54
Connecting the Printer to Your Computer ............................................................... 58
Viewing the PDF Manuals....................................................................................... 60
Printer Software Guide ...................................................................................... 60
ZoomBrowser EX Software User Guide/ImageBrowser Software User Guide........ 60
Uninstalling the Software ........................................................................................ 61
Windows ............................................................................................................ 61
Macintosh .......................................................................................................... 61
Uninstalling the Printer Driver ................................................................................. 62
Windows ............................................................................................................ 62
Macintosh .......................................................................................................... 63
Printing with Non-Canon Digital Cameras ................................................65
1
Enjoy Various Kinds of Printing
Connecting a camera to the printer and printing/Printing from a mobile phone
Some mobile phones
cannot use the IrDA
transmission feature.
Connecting the printer to a computer and printing
Software
CP Printer Solution Disk
2
Be sure to install the software
and the printer driver before
connecting the printer to the
computer.
L size paper
cassette
(sold separately)
Print easily at
home.
Credit card size
paper cassette
(sold separately)
Make label
stickers.
(8 per sheet)
Make original
large size
postcards.
Postcard size
paper cassette
Wide size
paper cassette
Various types of paper cassettes
Make borderless
wide size prints*
* Borderless printing
is not supported by
some cameras.
Season's Greetings
You can design layouts as you like.
Titles, captions, etc., can be added.
3
Printing Procedure and Reference Guides
Connecting a camera to the printer and printing/Printing from a mobile phone
Preparing
Connecting a Camera
Communicating with
the mobile phone
Basic
operations
Detailed
instructions
Reference
Guides
User Guide
(This Guide) p. 23
User Guide
(This Guide) p. 29, 32
Direct Print User Guide*
Connecting the printer to a computer and printing
Preparing
Installing the
Software
Reference
Guides
User Guide
(This Guide) p. 46
4
Connecting
Printing
Print settings are made
using the camera.
or
Camera User Guide*
Printing
Error Messages
Troubleshooting
* This does not explain how to print from a
mobile phone.
Please refer to the User Guide (this guide).
When using non-Canon digital cameras, refer
to the user guide that came with your camera.
Error Messages
Troubleshooting
Printer Software Guide (PDF Format)
: Included
with the printer
5
Package Contents
Compact Photo Printer
SELPHY CP600
Paper Cassette
(Postcard size)
Paper Cassette
(Wide size)
Standard Paper
(Postcard size,
5 sheets)
Ink Cassette
(Postcard size,
for 5 sheets)
CP Printer
Solution Disk
Battery Pack
NB-CP2L
Battery Pack
Terminal Cover
Cleaner Stick*1
Compact Power
Adapter CA-CP200
Power Cord
• User Guide (This Guide)
• Warranty Card*2
• Canon Customer Support Leaflet*2
*1 For information about how to use the cleaner stick, refer to Troubleshooting (p. 41).
*2 Not included in some regions.
6
The following products are sold separately.
Paper Cassette PCL-CP100
Paper Cassette PCC-CP100
Color Ink/Paper Set KP-36IP
Color Ink/Paper Set KP-108IP
Color Ink/Paper Set KL-36IP
Color Ink/Paper Set KC-36IP
Color Ink/Paper Set KW-24IP
Color Ink/Full-sized Label Set KC-18IF
Color Ink/Label Set KC-18IL
Battery Pack NB-CP2L
L size
Credit card size
Postcard size, 36 standard sheets
Postcard size, 108 standard sheets
L size, 36 standard sheets
Credit card size, 36 standard sheets
Wide Size (100 × 200 mm), 24 standard sheets
Credit card size, full-size, 18 Label sheets
Credit card size, Multiple (8-screen), 18 Label
sheets
Spare battery pack
Some products are not sold in some regions.
7
Quick Start
Let’s start by printing on postcard size paper.
This section explains the procedures required to print with the paper and the ink
cassette (trial kit) included with your printer.
General camera descriptions in this guide refer to digital cameras or digital
camcorders compatible with the compact photo printer (CP600). However, in
detailed instructions, “camera” refers to “digital cameras”, and “power source”
refers to “compact power adapter” throughout this guide.
The name of the button which is used for printing differs depending on the model of
your camera.
Things to Prepare
Printer (CP600)
Standard Paper (Postcard size, 5 sheets)
Ink Cassette (Postcard size, for 5 sheets)
Paper Cassette (Postcard size)
Compact Power Adapter CA-CP200
Power cord
Digital camera or digital camcorder
Memory card containing the images you wish to print
Camera User Guide or Direct Print User Guide
Interface cable included with your camera kit
: Included with the printer
1
1
8
Loading the Ink Cassette in the Printer (p. 25)
Open the ink cassette
compartment cover.
2
Load the ink cassette and
close the ink cassette
compartment cover.
2
Placing the Paper into the Paper Cassette (p. 26)
Paper (Glossy side up)
Top cover
Middle cover
Middle cover
(Address/stamp side next
to the middle cover)
1
Open the paper cassette’s
top and middle covers.
3
3
1
2
Place the paper (postcard size, 5
sheets), glossy side up and the
address/stamp side next to the
middle cover, in the paper cassette.
Place the middle cover back to its original position,
and leave the top cover open.
Loading the Paper Cassette into the Printer (p. 28)
Open the paper cassette
compartment cover.
2
Push the paper cassette all the way
into the paper cassette compartment,
with the cassette’s top cover open
and its middle cover closed.
9
Quick Start (Continued)
4
Connecting the Printer to a Power Source (p. 29)
1
Insert the power cord into
the compact power adapter
and plug the other end into
a power outlet.
DC IN terminal
To power outlet
2
Connect the compact power adapter to
the printer’s DC IN terminal.
5
1
Connecting the Camera to the Printer (p. 29)
Connect the interface cable (included with the
camera) to the camera’s DIGITAL terminal.
to DIGITAL
terminal
to USB terminal
Connect the interface
cable with its
mark
facing down
Direct print port
2
10
Connect the other end of the interface cable to
the printer’s direct print port.
6
Turn On the Power (p. 29)
Power Button
Indicator
Press the printer’s power button until the indicator lights green.
7
Printing (p. 31)
1
Turn the camera’s power on and display the images.
2
Press the camera’s
• The
(PictBridge) icon or the
(Canon Direct Print) icon appears on the
upper left corner of the LCD monitor.
, SET or SELECT button.
• The button to be pressed differs depending on the camera.
• If the
button is pressed, printing starts immediately.
Screen shot of the camera’s LCD monitor
(The screen shot differs depending on the
model of your camera.)
3
Select [Print] and press the SET or SELECT button.
• Printing starts.
• The color of the printer’s display window changes.
With certain camera models, the camera will power up and display its
images when it is connected to the printer with the interface cable. For
detailed instructions, please refer to the Camera User Guide or Direct Print
User Guide that came with your camera.
11
Before You Begin
Thank you for your purchase of the Canon Compact Photo Printer SELPHY
CP600. This guide explains the printer’s general flow of operations, from
camera print settings to printing and computer connection operations to
printing. For information about how to make prints, refer to the Camera User
Guide or Direct Print User Guide that came with your camera and to the
Printer Software Guide (bundled on the CP Printer Solution Disk).
Before using your printer for the first time, please read through the Safety Precautions
(p. 14).
† Warning Against Copyright Infringement
Please respect all copyrights. Use of images produced by this printer for purposes
other than personal entertainment may be prohibited by law.
† Warranty Limitations
This printer’s warranty is only effective in the country of sale. If a problem arises
while the printer is in use abroad, please convey it back to the country of sale before
proceeding with a warranty claim to a Canon Customer Support center.
For Canon Customer Support contacts, please see the Canon Limited
Warranty supplied with your printer.
Use of genuine Canon accessories is recommended.
12
This product is designed to achieve excellent performance when used with genuine Canon
accessories. Canon shall not be liable for any damage to this product and/or accidents
such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a
leakage and/or explosion of a battery pack). Please note that this warranty does not apply
to repairs arising out of the malfunction of non-genuine Canon accessories, although you
may request such repairs on a chargeable basis.
What Can Be Accomplished with this Printer
Connects directly to supporting Canon cameras
Allows easy printing from any Canon camera that supports direct printing with the compact
photo printer (CP600). Just connect the interface cable and you’re ready to go.
Connects directly to computers
Simply connect the printer to a computer with a commercially available USB cable to
perform the following operations:
• Print the shots taken with your camera in a variety of layouts
• Print part of an image (trimming)
• Print images with captions and artistic layout (Windows only)
• Make your own custom business cards
Four paper sizes and two types of labels
You can print on standard paper in postcard size, L size, credit card size or wide size
(100 × 200 mm (4 × 8 in.)). In addition to the standard size paper, you can print full-sized
labels or 8-label stickers on credit card size paper.
High-quality prints, fast paper feeding
Offers photo-quality prints. Produces up to 18* prints without reloading.
* Up to 12 prints when using wide size paper.
Fast printing
Postcard size images can be printed at a high speed of approximately 63 seconds per sheet*.
* The above printing speeds are applicable when a Canon compact digital camera equipped
with the DIGIC II is connected to the printer. Printing speeds may vary with other cameras.
Coated prints
Applies a protective coating to each print.
Borderless prints
Can produce borderless images that fill the paper completely.
Supports DPOF (Digital Print Order Format)
Supports DPOF settings for print selection, number of copies, and shooting date.
Easy outdoor printing
You can easily print outdoors by attaching the battery pack.
Printing from your mobile phone
You can transmit and print the images shot with a camera equipped mobile phone* using
infrared data communication.
* Only models with a camera function and an IrDA compliant infrared data communication
port.
• If the
or
icon does not display on the camera’s LCD monitor when you
connect your camera to this printer, your camera’s firmware may be incompatible
with this printer. Please check the Canon BeBit website (http://web.canon.jp/
Imaging/BeBit-e.html), or your regional Canon website, for information or to
download compatible firmware.
Since this printer complies with an industry standard for direct printing (PictBridge), you can
print with non-Canon cameras that also comply with this standard. For details, refer to page
65.
Symbols Used
: This mark denotes issues that may affect the printer’s operation.
: This mark denotes additional topics that complement the basic operating
procedures.
13
Read This First
Safety Precautions
• Before using the devices, please ensure that you have read and understood the safety
precautions described below. Always ensure that the devices are operated correctly.
• The safety precautions noted on the following pages are intended to instruct you in the safe
and correct operation of the devices to prevent injuries or damage to yourself and other
persons.
• “Devices” refers to the “printer”, “compact power adapter” or “battery pack” throughout this
guide.
WARNINGS
Do not play the supplied CD-ROM(s) in any CD player that does not support data CD-ROMs.
Playing the CD-ROM(s) in an audio CD player (music player) could damage the speakers. It is
also possible to suffer from hearing loss from listening with headphones to the loud sounds of a
CD-ROM played on a music CD player.
„ Devices
If the devices emit smoke or a burning odor, or show other signs of significant
malfunction, immediately unplug the power cord from the power outlet. Continued
operation under these conditions poses risk of fire or electric shock. Be sure that smoke or
burning odor subsides, and then contact your dealer or the nearest Canon Customer Support
help desk.
If the devices are dropped or the casing becomes damaged, unplug the power cord
from the power outlet. Continued operation poses risk of fire or electric shock. Contact your
dealer or the nearest canon Customer Support help desk.
Never rest small metallic objects or liquid containers on top of the devices. If liquid
splashes onto the devices, wipe the devices dry using a soft absorbent cloth. If liquid spills
into the devices or an object falls into the devices, immediately unplug the power cord from
the power outlet. Continued operation poses risk of fire or electric shock. Contact your dealer
or the nearest Canon Customer Support help desk.
Do not use flammable solvents such as alcohol, benzene, or paint thinner to clean the
devices. Use of such solvents poses a fire risk.
Do not drop or insert metallic or combustible objects into the devices. Entry of foreign
objects into the devices may result in fire, electric shock, or equipment failure. Store the
devices out of the reach of children.
Do not disassemble or modify the devices. The devices contain high-voltage components,
and there is risk of electric shock. If your devices need internal adjustments or repair, contact
your dealer or a Canon Customer Support help desk.
Do not touch metal parts of the devices or the power plug during thunderstorms.
Lightning strikes may produce lethal voltages within the devices. Keep clear of the devices
while thunderstorms are in progress.
14
„ Power
Do not exceed the cable and power outlet ratings when operating this product. Do not
operate this product outside of the specified voltage rating. Connecting too many devices to
the same outlet may result in fire. Check that the voltage of the outlet is compatible with the
devices before plugging them in.
If the power cord becomes damaged (if internal wiring is exposed, etc.), immediately
unplug it from the power outlet. Continued use poses risk of fire or electric shock.
Do not plug in or unplug the power cord while your hands are wet, as this may result in
electric shock. When unplugging the power cord, hold it firmly at the plug area. Do not pull
directly on the cord, as this may damage or expose the cord’s internal wiring, resulting in risk
of fire or electric shock.
Be sure that the power cord is plugged all the way in. A loose connection may result in
heat buildup, fire, or electric shock.
Do not damage, modify, or rest heavy objects on the power cord. Damage to the cord
may result in the exposure of live wires, fire, or electric shock.
Keep the power cord free of dust. The presence of dust or metallic debris on the plug
poses risk of fire or electric shock. If the plug area is not clean, unplug the power cord and
then wipe the plug area clean using a dry cloth. Check the plug periodically to make sure it is
clean.
„ Usage Location
Do not place the devices on an unstable or tilted table or desk, as there is risk that the
devices may fall and cause injury.
15
CAUTIONS
„ Devices
Do not block the air vents on the printer. Blocking the vents may cause the inside of the
printer to overheat, resulting in damage to internal components and risk of equipment failure
or fire. Use the devices in a well-ventilated area.
Do not rest heavy objects on the devices. Objects may fall off the devices and cause
injury. Weight placed on the devices may deform the casing, resulting in damage to internal
parts and posing risk of fire.
Unplug the devices when you are not using them. If the devices remain plugged in, there
is risk that accidental contact with the device’s internal parts may cause electric shock.
Leaving the devices plugged in during prolonged periods of non-use poses risk of fire.
Do not remove the paper cassette from the printer while printing is in progress. Paper
moves back and forth in the cassette four times during printing. Placing your hand in the way
of moving paper may result in injury. Wait for printing to finish completely before removing the
cassette. Never place your hand into the paper cassette slot.
Do not reach into internal parts of the devices except as specified in the operating
instructions. Reaching into inappropriate parts of the devices may cause your hand to
become caught or injured.
„ Power
Do not move the devices while they are plugged in. Doing so may damage the power
cord. Continued use of a damaged power cord poses risk of fire or electric shock.
Do not excessively bend or twist the power cord. Doing so may damage the cord.
Continued use of a damaged cable poses risk of fire or equipment failure. Leave about 15 cm
(6 in.) of clearance at the front and back of the devices and 10 cm (4 in.) of clearance on both
sides to ensure adequate ventilation.
Do not pull on the power cord. Doing so may damage the power cord. Continued use of a
damaged cord poses risk of fire or electric shock. Always hold the cord by the plug area when
unplugging it.
16
„ Usage Location
Do not use the devices in locations that are smoky, humid, dusty, or subject to strong
vibration. Entry of water or dust into the devices, or internal damage caused by strong
vibration, may pose risk of fire or electric shock. Have the devices checked approximately
once a year (contact your dealer), preferably before the onset of your area’s humid season.
Do not leave the devices exposed to high temperatures. Do not leave in direct sunlight, or
close to heating equipment, or in a car with windows closed on a hot day. High temperatures
may cause deformation of the devices and pose risk of fire.
Do not use the devices near an open flame. Sheets ejected from the printer (onto the top
of the paper cassette) may fall into the flame, resulting in fire.
Do not use the devices close to TV sets or AM radios. Devices’ operation may adversely
affect TV and radio reception.
17
Proper Usage and Handling
„ Usage Location
Do not use near strong magnets or near devices that produce strong electromagnetic
fields. Electromagnetic radiation from devices such as TVs and game machines, and strong
magnetic fields from devices such as speakers and large motors, may cause distortion in
printed images.
Use in a well-ventilated, level area.
Leave about 15 cm (6 in.) of clearance at the front and back of the devices and 10 cm
(4 in.) of clearance on both sides. Be sure to leave clearance around the paper-handling
slot (at the rear) so that paper has sufficient room to jut out from the slot during printing.
Place the printer so that the air vents on the back will not be blocked. If the air vents
blocked, the printer interior could heat up, causing the printer to temporarily stop.
„ Handling Precautions
Please avoid turning the printer’s power on and off needlessly as the printer
initialization consumes ink. There may not be enough ink left for the allotted sheets in the
set.
When the printer is not in use, please remove the battery pack.
Unplug the printer when you are not using it. But please note that you should plug in and
run the printer at least once every six months to ensure that it remains functional.
Before transporting the printer, remove the paper and ink cassettes and close the
paper cassette cover and the ink cassette cover. If dirt or foreign objects enter the printer,
print quality may deteriorate.
Pack the printer into an appropriate case for transport. If a case is not available, wrap it
with cloth or other protective material to protect against scratches.
Never use volatile compounds or insecticides on the printer, and do not allow rubber
or vinyl material to remain in prolonged contact with the printer. These materials may
cause deformation of the printer’s casing.
† Overheating
If the printer overheats, it will temporarily stop operating. This does not mean that the
printer has malfunctioned. The printer will resume normal printing as soon as it cools
down.
Temporary stoppages are most likely to occur in the following cases:
• When printing continuously.
• If the room is unusually warm.
• If the air vents on the back of the printer are blocked or if ventilation is inadequate.
18
† To Prevent Damage from Condensation
Condensation may form in the printer if you suddenly move it from a cold location to a
warm location. To prevent damage that might be caused by condensation, place the printer
in a sealed plastic bag prior to moving it, and allow it to reach room temperature before using
it. Stop using the printer immediately if you detect condensation. Continued use may damage
the equipment. Wait until the water droplets have evaporated completely before resuming
use.
† Cleaning the Printer
Never use benzene, paint thinner, or other volatile solvents to clean the printer. Volatile
solvents may cause deformation or peeling of the printer’s casing. To clean the printer, wipe it
with a soft dry cloth. If stronger cleaning is required, wipe first with a cloth moistened with a
dilute neutral solvent, then wipe again with a soft dry cloth. If you use a chemical cleaning
cloth, read the instructions that come with it and observe all indicated precautions.
Keep the air vents clean and free of dust. Clean the vents as necessary. Dust that enters
the printer through the vents may land on the ink sheet, resulting in poor print quality and
possibly leading to printer breakdown. If the ink sheet becomes dusty, remove the ink
cassette and replace it with a new one.
„ Proper Handling of Ink Cassettes
Please use only the ink cassettes specified for use by Canon.
Do not open the ink cassette cover while printing is in progress, and do not pull the
ink cassette out. These actions may damage the printer.
Do not touch or pull on the ink sheet. There may not be enough ink left for the allotted
sheets in the set.
Do not handle the ink cassettes with wet or sweaty hands.
Allow ink cassettes to reach room temperature before installing and using them.
Condensation may form if you suddenly move ink cassettes from a cold location to a warm
location. If there is risk of condensation, leave the cassette in its packaging until it reaches
room temperature, and wipe away any moisture before loading it.
If you are not planning to use the printer for a while, remove and store the ink cassette.
19
„ Proper Handling of Paper Cassettes
Do not apply excessive force to the paper cassette. Force or impact on the cassette may
result in paper jams or equipment damage.
Do not bend or deform the spring located at the rear of the middle cover of the paper
cassette.
Spring
Do not place any foreign objects in the print output receptacle (on the top of the paper
cassette). This area is for paper only.
If you are not planning to use the printer for a while, remove the paper cassette, close
the paper cassette’s top cover and store the paper cassette. Also remove the paper
from the paper cassette and store it horizontally.
„ Proper Handling of Paper
Please use only the paper types specified for use by Canon.
Paper must be printed on the glossy side (the side without any printed markings).
Always load paper into the cassette with the glossy side up. Loading the paper the wrong way
may result in poor print quality, and in some cases may cause damage to the printer.
Do not tear or bend the paper’s perforated edges before printing. Tearing the paper’s
perforated edges will cause the ink sheet to wind up automatically and waste one print’s
worth of ink. If this happens, there will not be enough ink left to print all the paper sheets
included in the kit.
Do not use label sheets on which labels are partially peeled off.
Do not touch the print side of the paper with your fingers. Always hold the paper along
the edges (outside the perforated border).
WRONG
RIGHT
Be sure that hands are dry before touching the paper. Sharp objects will scratch the paper
surface. Keep the paper surface free from fingerprints, dust, water droplets, etc.
Do not write on the paper before printing. Writing on paper before printing on it may result
in malfunction.
20
Do not touch paper while it is being printed. During printing, the sheet repeatedly moves
back and forth along the top of the paper cassette and in and out through the paper-handling
slot. Please do not touch the sheet during this process as this could damage the printer.
Do not allow too many prints to accumulate in the print output receptacle. Do not allow
more than 9 sheets to accumulate in the print output receptacle.
You may write on the paper with an oil-based pen, but to avoid smudging please allow
ink time to dry before touching it.
Allow the paper to reach room temperature before installing and using it. Condensation
may form if you suddenly move the paper from a cold location to a warm location. If there is
risk of condensation, leave the paper in its packaging until it reaches room temperature, and
wipe away any moisture before loading it.
Please avoid the following actions as they may result in color change, color fading or
color bleeding.
• Sticking any type of adhesive tape onto the print surface.
• Allowing print surfaces to come into contact with vinyl materials.
• Applying alcohol or other volatile solvents to the print surface.
• Leaving print surfaces tightly pressed against any other surfaces or objects for prolonged
periods.
„ Paper Storage
If you wish to mount prints into an album, select an album with nylon-based sleeves,
or with propylene or cellophane sleeves. Other types of sleeves may cause color loss or
color bleeding.
Color change may occur over time in accordance with conditions of storage. Canon
assumes no liability for color changes.
To avoid print quality deterioration, do not store your prints in the following types of
locations.
• Locations that reach temperatures above 40 °C (104 °F)
• Humid or dusty locations
• Locations exposed to direct sunlight.
Remove unused paper from the paper cassette, return it to the bag and then into its
original package. Store the package horizontally.
„ Others
When opening a color ink/paper set (full-sized label set, label set), check the contents.
If something seems to be missing or appears to be damaged, contact the dealer for
assistance.
The battery pack is charged while installed on the printer, and the printer is connected
to the compact power adapter supplied with the printer.
When using the battery pack, if the battery status is low, the finished print may not be
ejected into the print output receptacle completely. If this happens, gently pull out the
paper.
21
Components Guide
„ Compact Photo Printer SELPHY CP600
Front View
Indicator
Indicates the printer’s status.
Orange: Charging the battery pack
Off: Charging complete
Green: Ready to print
Blinking green: Printing in progress
Blinking orange: Battery depleted
Red/Blinking red: Error
Power Button
Turns the printer’s power
on and off.
Display Window*
Lights during printing
in the following order:
yellow Æ pink (magenta) Æ light
blue (cyan) Æ white Æ blue.
Infrared Data
Receiver
Used for infrared
data
communication
with a mobile
phone.
Paper Cassette Slot
The paper cassette loads
into this compartment.
Ink Cassette
Compartment Cover
Ink Cassette Slot
The ink cassette is inserted
into this compartment.
Paper Cassette
Compartment Cover
* The display window is covered with a thin plastic film for protection against
scratches during shipment. Remove it before using the printer.
Back View
Battery Cover Lever
Used when the battery pack or
battery cover is removed.
USB Port
Connects commercially
available USB cables to a
computer.
Direct Print Port
Air Vents
Battery Cover
Paper-handling Slot
Paper extends out from this slot
while printing is in progress.
22
Connects the interface cable
(included with the camera) to the
camera.
DC IN Terminal
Connects to the Compact Power Adapter.
Let’s Print
Preparing Your Ink Cassette/Paper Sets and
Paper Cassette
Since there are several kinds of ink/paper set (including the separately sold sets),
please make sure you are using the right ink cassette and paper cassette for the
chosen paper. If the set is not correct, you will not be able to print.
Please check the sets and the names of their components in the table below.
Look here for the paper cassette name
Look here for the ink cassette name
„ Checking Your Ink/Paper Sets
† Printing on Postcard Size Paper (100 × 148 mm (4 × 6 in.))
Paper
Number
of
Sheets
Paper Cassette
Name
Ink Cassette Name
The design of the label on your ink cassette
may slightly differ from the examples below.
5
36
•
Included in package
† Printing on L Size Paper (89 × 119 mm (3.5 × 4.7 in.))
Paper
Number
of
Sheets
Paper Cassette
Name
Ink Cassette Name
The design of the label on your ink cassette
may slightly differ from the examples below.
36
• The paper cassette PCL-CP100 (sold separately) is required when printing on L size paper.
23
† Printing on Credit Card Size Paper (54 × 86 mm (2.1 × 3.4 in.))
Paper
Number
of
Sheets
Paper Cassette
Name
Ink Cassette Name
The design of the label on your ink cassette
may slightly differ from the examples below.
36
Standard Paper
18
Full-sized Label
18
8-sticker Label
• The paper cassette PCC-CP100 (sold separately) is required when printing on credit card
size paper.
† Printing on Wide Size Paper (100 × 200 mm (4 × 8 in.))
Paper
Number
of
Sheets
Paper Cassette
Name
Ink Cassette Name
The design of the label on your ink cassette
may slightly differ from the examples below.
24
† Separately Sold Ink and Paper Products
You can use the following color ink/paper sets (sold separately) with the Canon
Compact Photo Printer SELPHY CP600.
Paper Size
Contents
Product Name
Postcard size
Standard paper (36 sheets)
Dedicated ink cassette
Color Ink/Paper Set KP-36IP
L size
Standard paper (36 sheets)
Dedicated ink cassette
Color Ink/Paper Set KL-36IP
Credit card size
Standard paper (36 sheets)
Dedicated ink cassette
Color Ink/Paper Set KC-36IP
Full-sized label (18 sheets)
Dedicated ink cassette
Color Ink/Full-Sized Label Set KC-18IF
8-sticker label (18 sheets)
Dedicated ink cassette
Color Ink/Label Set KC-18IL
Standard paper (24 sheets)
Dedicated ink cassette
Color Ink/Paper Set KW-24IP
Wide size
(100 × 200 mm
(4 × 8 in.))
• One ink cassette can print to all of the paper included in the ink/paper set.
24
Loading the Ink Cassette
1
Open the ink cassette
compartment cover.
2
Remove any slack from the ink
sheet.
Ink sheet
3
Sprocket
Clip
• Push in on the sprocket, and turn it gently in
the indicated direction to take up the slack
until the ink sheet straightens out (It will not
be possible to print to all of the paper if you
overwind the ink sheet).
Hold the cassette so that the
embossed arrow is at the top,
and insert it all the way into the
compartment (in the direction of
the arrow).
• Be careful to avoid touching or pulling on the
ink sheet when inserting the cassette.
• Push the cassette all the way in, so that it
clicks into place.
• When you are ready to remove the ink
cassette, lift the clip and pull the cassette
out.
4
Close the ink cassette
compartment cover.
• You can check the name of the ink cassette
in the printer through the display window on
the top of the printer.
Display
Window
• Do not reuse empty ink cassettes. Attempting to reuse an empty ink
cassette may result in malfunction or damage to the printer.
• Please also refer to the Proper Handling of Ink Cassettes section of Proper Usage
and Handling (p. 19).
25
Placing the Paper into the Paper Cassette
1
Open the paper cassette’s top
cover and middle cover.
Top
cover
• Open the top cover, then push the middle
cover in the direction of the arrow and lift it
up.
Middle cover
2
Paper (Glossy side up)
Fan the paper stack properly and
place the paper into the paper
cassette, with the printable side
(glossy side) facing up.
• Insert the postcard size paper with the
glossy side up and the address/stamp side
next to the middle cover as shown in the
figure.
• Do not touch the glossy side of the paper (to
avoid fingerprints) when you fan the paper
stack.
(Address/stamp side next to
the middle cover)
• Insert the credit card size paper as shown in
• Insert the wide size paper
the figure below.
(100 × 200 mm (4 × 8 in.)) as shown in
the figure below.
Paper (Glossy side up)
Wide Size
26
Credit Card Size
(Standard Paper/
Full-sized Label)
Credit Card Size
(8-label Sticker)
• Insert the L size paper as shown in
the figure below.
Paper (Glossy side up)
L Size
3
Place the middle cover back to
its original position.
• After pulling the middle cover down, slide it
in the direction of the arrows until it clicks
back into place.
• Do not close the top cover.
• Please use specified paper types only.
• Do not insert more than 18 sheets in the paper cassette.
• Do not insert more than 12 sheets wide size paper (100 × 200 mm (4 × 8 in.)) in
the paper cassette.
• Printed or fed paper is coated even when nothing is printed on the paper.
Therefore, never reuse the printed or fed paper for printing. Reused paper
may stick to the ink sheet, resulting in damage to the printer.
• Please also refer to the Proper Handling of Paper Cassettes and the Proper
Handling of Paper sections of Proper Usage and Handling (p. 20).
27
Loading the Paper Cassette
1
Open the paper cassette
compartment cover.
2
Push the paper cassette all the
way into the paper cassette slot.
• Be sure the paper is set correctly before
pushing the cassette in.
• Insert the paper cassette evenly so that it
slides over the bottom of the slot entrance.
Middle cover
closed
Top cover open
• Do not remove the paper cassette while feeding, printing, or ejection is in
progress.
• The printer outputs the finished prints into the receptacle onto the top of the printer
cassette (top of the middle cover or inside of the top cover). Be sure to close the
middle cover and open the top cover so that output can proceed normally.
Print receptacle
28
Connecting a Power Source and the Camera to
the Printer
Connect the camera to the printer using the cable (included with the camera)
and turn the printer’s power on.
For more detailed camera connection instructions, refer to your Camera User
Guide or Direct Print User Guide.
To DIGITAL terminal
5
7
To DC IN terminal
1
15 cm (6 in.) at the
front and back of the
devices and 10 cm
(4 in.) on both sides
or more of open
space
Camera*1
Interface cable
included with
the camera
4
6
2
Compact power adapter
3
To power
outlet
Camera’s Compact
Power Adapter (sold
separately or included
with the camera)*2
To power outlet
*1 Canon cameras compatible with CP600, and non-Canon cameras compatible with
PictBridge can also be connected.
*2 Please use the camera’s compact power adapter or a fully charged battery pack
(or charged batteries).
The numbered steps in the following instructions refer to the numbers in the above
illustration.
1
Place the printer on a flat area.
2
Connect the supplied power cord to the supplied Compact
Power Adapter CA-CP200.
• Be sure to leave about 15 cm (6 in.) of clearance around the paper-handling slot
(at the rear) so that paper has sufficient room to jut out from the slot during
printing.
29
3
4
5
6
7
Insert the plug in a power outlet.
Connect the Compact Power Adapter cable to the printer.
Connect the interface cable to the camera.
• Use the interface cable that came with your camera.
Connect the interface cable to the printer.
• Insert the cable in the left port, with the
mark on the cable facing down.
Press the power button until the indicator goes on.
• The indicator lights green once the printer powers up.
„ Turning the Printer’s Power Off
Press the power button until the indicator goes off.
• We recommend that you also connect the camera’s compact power adapter (sold
separately or included with the camera) when using the camera with your printer. If
you wish to run the camera on battery power, be sure that batteries are fully
charged.
• When connecting the cable, be sure that the connectors on the cable match up
correctly with the connectors on the camera and printer.
• Use an easily accessible power outlet for the printer’s power cord, so that you can
unplug the printer cable quickly in the event of a problem.
• Please also refer to the Usage Location section of Proper Usage and Handling for
information about printer usage location (p. 18).
• Some camera models do not come with a compact power adapter. For details,
please see the System Map that came with your camera.
30
Printing
This section explains the flow of printing operations with Canon cameras*.
For more details, refer to your Camera User Guide or Direct Print User Guide.
* In other cases, please refer to the Printing with Non-Canon Digital Cameras (p. 65).
1
2
Turn the camera’s power on and
display the images.
• Check that the
(PictBridge)/ (Canon
Direct Print) icon is displayed in the upper
left corner of the LCD monitor.
• Some camera models automatically power
up when the cable is connected to the
printer. The icon then displays on the LCD
monitor.
Display the images to be printed and press the SET or
SELECT button.
• If your camera has the
after you press the
(Print/Share) button, printing starts immediately
button (Step 3 is not necessary).
3
Select [Print] and press the SET
or SELECT button.
The screen shot differs depending
on the model of your camera.
If
or
• Printing starts. The camera returns to the
playback screen once printing is
successfully completed.
• The display window light changes color
during printing in the following order:
yellow Æ pink (magenta) Æ light blue (cyan)
Æ white Æ blue.
does not display in step 1, check the following:
• Is the cable correctly connected? (p. 29)
• Is the printer’s power on? (p. 29)
• Is your camera’s firmware compatible with this printer?
Check the Canon BeBit website or your regional Canon website.
If printing does not start, check the following:
• Does the camera’s LCD monitor display a message? (p. 42)
31
„ Printing on Wide Size (100 × 200 mm (4 × 8 in.)) Paper
The printing area may vary depending on the camera use.
The cards are printed as explained below.
If
appears in step 1 on page 31
Printed on the whole card.
If
appears in step 1 on page 31
Printed on the 100 × 150 mm
(4 × 6 in.) portion of the card.
The upper and lower portions of an image are
trimmed.
Nothing is printed on this portion so you can
write your message with an oil-based pen.
• If
appears in step 1 on page 31, select [Default] on the paper size setting
screen.
„ Printing Images from a Mobile Phone
You can transmit and easily print out the images shot by a camera equipped mobile
phone.
The mobile phone must have the following features.
• JPEG image recording capacity
• Infrared data communication (with an IrDA compliant infrared data communication
port)
Refer to your mobile phone's manual when using infrared data communication.
1
2
32
Shoot an image using your mobile phone.
• Set the image type to JPEG.
If any camera is connected to the printer, disconnect the
camera.
• You can leave your computer connected to the printer.
3
Load the paper cassette that
matches the size of paper you
want to print and the ink
cassette.
• The printer enlarges or reduces the size of
the image according to the paper size and
sets the print direction to vertical or
horizontal automatically. The upper, lower,
left or right portion(s) of the printed image
may be cut depending on the combination of
the image size and paper size.
• When you print wide size paper (100 x 200
mm (4 × 8 in.)), the size of the printed image
will be the same as the postcard size. You
cannot do full-size borderless printing.
4
20 cm or nearer (Do not
block with any obstacles.)
Effective range (about 10 degrees
vertically and horizontally).
5
Transmit an image from your
mobile phone to the printer.
• Aim the mobile phone's infrared port at the
printer's infrared data receiver and transmit
the image data to the printer. See the
illustration on the left for the transmittable
distance. Note that the distance differs
depending on the mobile phone model.
Refer to your mobile phone's manual.
• The printer's indicator blinks green while
receiving the data. If any error occurs the
indicator lights green (returns to the original
state). Check the message appearing on
the mobile phone display if an error occurs.
• If the data transmission fails, move the
mobile phone closer to the front of the
printer's infrared data receiver and repeat
the procedure.
Printing starts after the data transmission is complete.
33
• E-mail and phone directories cannot be printed.
• Images downloaded from internet homepages or images originally downloaded
from a URL and attached to e-mail cannot be printed. This restriction is for
protecting mobile phone security.
• Some mobile phones have limited memory capacity for infrared data transmission
and you may not be able to print the image in the best quality.
• The images in the memory card (such as an SD card or memory stick) of some
mobile phones cannot be printed.
• Movie images cannot be printed.
• If the printer cannot recover from an error, such as a paper jam, turn off the printer
and remove any paper from inside the printer. Turn it on, and repeat the procedure.
• Do not place any obstacle between the printer and the mobile phone.
• Avoid direct sunlight on the infrared data receiver. Direct sunlight may interfere
with the communication with the mobile phone.
• Do not place the printer near a plasma display. Placing it near a plasma display
may prevent the printer from communicating with the mobile phone.
• Do not interrupt the infrared data communication until printing completes. If the
communication is interrupted, turn off the printer. Then, turn it on, and repeat the
procedure.
• If you print L size, postcard size or wide size paper, the printed image may be
coarser and grainier. In this case, printing on credit card size paper is
recommended.
• If you transmit a large image, the transmission may take more than one minute.
• Do not do any printing operations from the camera or computer after the printer
starts communicating with the mobile phone until printing is complete.
• The printer cannot communicate with the mobile phone until all other printing
operations are complete.
† When the Indicator Blinks
The indicator of the printer blinks if any error occurs during printing.
Indicator
34
Cause
Solution
Blinks green and red in turn.
No paper in the paper cassette.
Load paper into the cassette,
printing resumes.
Blinks in the following order:
green Æ red Æ red.
The ink cassette is out of ink.
Load a new ink cassette, printing
resumes.
Blinks in the following order:
green Æ red Æ red Æ red.
The paper and ink are from
different sets.
Check the ink/paper sets. If you
set them properly, printing will
resume.
Blinks red.
An unusual error such as a paper Turn off the printer and turn it on
jam has occurred.
again. Repeat the operations from
the beginning.
Battery Usage
Using the Battery Pack
You can use the rechargeable battery pack (Battery Pack NB-CP2L) to print.
The Battery Pack NB-CP1L (sold separately) cannot be used.
„ Charging the Battery Pack
Attach the battery pack NB-CP2L to the printer to charge it.
1
Remove the battery pack’s
terminal cover.
• When the battery pack is not in use, always
store it with its terminal cover on.
Terminal Cover
2
Press the battery cover lever
down and remove the battery
cover.
3
Install the battery pack.
4
• Slide the battery pack into place, in the
direction of the arrow, and push it in until it
clicks into place.
• To remove the battery pack, push the
battery cover lever down and pull the battery
pack out. Replace the battery cover
afterwards.
To Power Outlet
Attach the power cord to the
compact power adapter CACP200 and plug it into a power
outlet.
Compact Power Adapter
power cord
35
5
Indicator
Connect the compact power
adapter cable to the printer.
• The indicator lights orange while charging
and turns off once the battery pack is fully
charged.
Compact Power
Adapter Cable
6
Disconnect the compact power
adapter cable from the printer
once charging is complete.
• If the power button is pressed and the printer’s power turns on while charging the
battery pack, charging will stop. Pressing the power button again will turn off the
printer and charging will resume.
• Do not use the battery pack in products other than those recommended by Canon.
• Do not charge battery packs other than the battery pack NB-CP2L.
• Do not carry or store the battery pack with metal objects with sharp edges, such as
paper clips and pins. Always put the terminal cover on the battery pack’s terminal
when carrying it or before storing it.
• Avoid dropping or subjecting the battery pack to severe impact.
• Do not apply heat or expose the battery pack to open flame.
• Do not cover the compact power adapter with anything, such as a tablecloth,
cushion or blanket, when it is charging. Heat will build up internally and possibly
lead to fire.
• Immediately flush water over parts of the body or clothing that come into contact
with the inner contents of a battery if the outer casing incurs damage. If any of
these substances should contact internal tissues, such as eyes or the mouth,
immediately flush with water and seek medical assistance.
36
• When the battery pack is used to power the printer, the printer will automatically
turn off if it is idle for 5 minutes or more.
• This is a lithium ion battery pack so there is no need to completely use or
discharge it before recharging. It can be charged at any charge state.
• It takes approximately 150 minutes to bring a fully discharged battery pack to a full
charge state (based on standard Canon testing criteria).
• Charge it within a temperature range of 5 to 40 oC (41 to 104 oF).
• The charge adapter may emit noises while charging. This is not a malfunction.
• Do not charge the battery pack for more than 24 continuous hours to avoid
performance loss.
• When the printer is not in use, remove the battery pack, replace its terminal cover
and store it in a cool place (30 oC/86 oF or less). Charge it before using it again.
• Even charged battery packs continue to discharge naturally. You are advised to
charge the battery on the day of use, or one day before, to ensure a full charge.
• Since storing a fully charged battery pack for long periods of time (about 1 year)
can shorten its lifecycle or affect performance, you are recommended to discharge
the battery pack fully in the printer before storing it in a cool place (30 oC/86 oF or
less). If you do not use the battery pack for long periods of time, charge it fully and
discharge it fully in the printer at least once a year before returning it to storage.
• The printer consumes the battery charge when the power is on even when a
function is not being used. To conserve the battery charge, be particularly attentive
in turning the power off.
• Remove the battery pack when the printer is not in use. The battery pack
continues to discharge a small amount when left in the printer even with the power
turned off. This shortens the battery life.
• Although the battery pack’s maximum operating range is 5 to 40 oC (41 to 104 oF),
the optimal range is 10 to 30 oC (50 to 86 oF). At cold temperatures, such as those
experienced on ski hills, performance will temporarily decline, reducing the usable
time.
• If the usable time of a battery pack diminishes substantially even when fully
charged, it should be replaced.
37
„ Battery Status
If battery status is running down and the indicator of the printer blinks orange while
the printer is connected to the camera, the camera’s LCD monitor may display the
following message.
Error Message
Recharge the printer battery
Solution
The battery pack’s power is too low to operate the printer.
Switch the battery pack for a fully charged one or recharge
the battery pack.
„ Battery Performance
Number of prints
Postcard size paper: Approximately 36 sheets
L size paper: Approximately 36 sheets
Card size paper: Approximately 72 sheets
Wide size (100 × 200 mm (4 × 8 in.)) paper: Approximately 24 sheets
Test conditions: Normal temperature (23 °C/73 °F), Canon images, continuous print.
* The above data may vary according to the printing environment and the image to be printed.
* At low temperatures, the battery pack performance may diminish and the low battery icon
may appear very rapidly.
38
Troubleshooting
If the printer does not seem to be working properly, run through the checks
below to see if you can identify and correct the problem. If you are not able to
solve the problem, please call your dealer or contact a Canon Customer
Support help desk for assistance.
Problem
The printer has no power.
Cause
The compact power adapter or
power cord is not correctly
connected.
Solution
Be sure that the compact power
adapter and power cord are
connected correctly. Be sure that
the power cord is plugged into a
standard power outlet.
The printer’s indicator is blinking There is a malfunction in the
red.
printer.
Turn the printer’s power off and
turn it on again.
The (PictBridge)/ (Canon
The cable is not correctly
Direct Print) icon does not display connected.
in the upper left corner of the LCD The printer’s power is off.
monitor.
Connect the cable correctly.
(p. 29)
The printer does not print.
Turn the printer’s power on.
(p. 29)
Your camera’s firmware is
incompatible with this printer.
Please check the Canon BeBit
website or your regional Canon
website.
The printer is connected to a
computer and printing is in
progress.
Wait until the print outputted by
the computer is complete.
The printer is not correctly
connected to the camera.
Connect the cable correctly.
(p. 29)
If the connection is correct, the
or icon will appear on the
camera’s LCD monitor.
The camera’s batteries are
depleted.
Replace with fully charged
batteries, or plug the camera into
a power outlet (using the
camera’s optional compact power
adapter).
The ink cassette is not loaded
correctly.
Load the ink cassette correctly.
(p. 25)
Too much slack in the ink
cassette’s ink sheet.
Take up the slack. (p. 25)
The paper cassette is not pushed Load the paper cassette correctly.
all the way in.
(p. 28)
Printing stopped midway.
The printer has overheated.
Wait for the printer to cool down.
The printer is not correctly
connected to the camera.
Connect the cable correctly.
(p. 29)
39
Problem
Cause
Solution
The printer’s indicator lights red
without the camera’s LCD
monitor displaying any error
message.
There is a malfunction in the
printer.
Remove the paper from the
paper-handling slot and take up
any slack in the ink sheet. Turn
the printer’s power off and turn it
on again.
Print quality is not good.
You are not using the correct
paper type.
Use the designated paper type.
Paper is loaded with the wrong
side up.
Load the paper correctly. (p. 26)
The ink sheet or paper is dirty.
Use a clean ink sheet and clean
paper.
Condensation has formed inside
the printer.
Wait for condensation to
evaporate. (p. 19)
The printer is too close to a TV,
video game machine, or other
electromagnetic source.
Move the printer so that it is at
least 1 meter (3.3 ft.) away from
the electromagnetic source.
Printed images are distorted.
The printer is too close to a stereo Move the printer away from the
speaker, large motor, or other
strong magnetic source.
strong magnetic source.
There is not enough ink left for
the allotted sheets in the set.
You turned the printer’s power on Please avoid turning the printer’s
and off repeatedly.
power on and off needlessly.
You pulled on the ink sheet.
Do not pull on the ink sheet by
force.
You tore or bent the paper’s
Do not tear or bend the paper’s
perforated edges before printing. perforated edges.
You removed the ink cassette
when paper run out while the
printer was printing more than
one sheet of paper.
Load paper into the paper
cassette without removing the ink
cassette.
Nothing happens when the
camera’s
or SET button is
pressed.
The printer has overheated.
Wait for the printer to cool down.
Printing is in progress.
Wait for the printer to finish
printing.
Frequent paper jams.
The paper cassette is overloaded. Do not load more than 18 sheets
of paper into the cassette.
Do not insert more than 12 sheets
of wide size paper (100 ×
200 mm (4 × 8 in.)) in the paper
cassette.
The print output receptacle is too Do not allow more than 9 sheets
full.
to accumulate in the receptacle.
Paper is creased or curled.
40
Do not use paper that is creased
or curled.
Problem
Faint stripes appear in the print.
Cause
Dust has accumulated inside the
printer.
How to use the cleaner stick
Remove the ink cassette and insert the cleaner
stick in the direction of the arrow and with the
arrow on the cleaner stick facing up.
Push it in completely and slide it in and out of
the printer 2 or 3 times.
Solution
Remove the dust inside the
printer using the cleaner stick
(refer to Figure A).
Figure A
41
Error Messages
If a problem occurs while the printer is connected to the camera, the printer’s
indicator will light or blink red and the camera’s LCD monitor may display one of
the messages indicated below. If the camera is connected to a TV, the message
will appear on the TV screen.
Depending on the camera model, some messages will not be displayed.
Error Message
No paper
42
Cause
Solution
Paper cassette is incorrectly
installed.
Load the paper cassette correctly.
No paper in the paper cassette.
Load paper into the cassette.
Paper is not feeding correctly.
Take out the paper cassette, and
then manually remove any paper
remaining in the printer.
Paper Error
Paper is not loaded correctly in
the paper cassette.
Load paper into the cassette
correctly.
No Ink
No ink cassette in the printer.
Load an ink cassette.
The ink cassette is out of ink.
Load a new ink cassette.
Incompatible paper size
Wrong paper size is loaded in the Use the designated paper size.
printer.
Ink Error
or
Ink cassette error
The ink cassette is not working
correctly.
Remove the ink cassette from the
printer, take up the slack in the ink
sheet, and then reload the
cassette. If this does not solve the
problem, replace with a new ink
cassette. If the ink cassette is
stuck in the printer, contact a
Canon Customer Support help
desk for assistance.
Paper and ink do not match
The paper and ink are from
different sets.
Check the ink/paper sets.
Paper Jam
Paper jammed during printing.
Turn the power off and turn it on
again.
If the printer fails to eject the
paper, contact a Canon Customer
Support help desk for assistance.
Paper has been changed
Paper was changed after the print Change back to the original paper
menu was displayed.
size or change the print settings.
Recharge the printer battery
The printer’s battery pack is
depleted.
Change it with a fully charged
battery pack or recharge the
battery pack. You can also use the
printer’s compact power adapter.
Error Message
Cause
Solution
Communication error
Error in communication between Turn the printer and camera
printer and camera.
power off and turn it on again.
If the error message does not
clear, contact a Canon Customer
Support help desk for assistance.
Cannot print!
The image was taken with a
different camera, recorded in a
different type, or has been altered
by a computer.
Check whether the image’s size
matches the camera’s pixel
capacity. If the size is not
appropriate, resize the image and
convert it as necessary to a JPEG
image that the camera can
display.
Could not print xx images
You have selected a number of
images for DPOF printing, but
some of these images cannot be
printed because they were taken
with a different camera, recorded
in a different type, or have been
altered by a computer (xx
indicates the number of
unprintable images from among
those selected).
Check whether the image size
matches the camera’s pixel
capacity. If sizes are not
appropriate, resize the images
and convert them as necessary to
JPEG images that the camera can
display.
Hardware Error
Error other than a paper or ink
error.
Check whether or not an error
other than a paper or ink error
has occurred.
File Error
You tried to print an image that is Some images that have been
not PictBridge compliant.
recorded with another camera or
modified using a computer
cannot be printed. Convert the
images as necessary to JPEG
images that the camera can
display.
43
Specifications
„ Compact Photo Printer SELPHY CP600
† General Specifications
Printer Type
Full-color direct digital printer
Print Method
Dye-sublimation thermal transfer (with overcoating)
Resolution
Reproduction
300 × 300 dpi
Gradation
256 gradations/color
Ink
Dedicated ink cassette for each paper size (Y/M/C/overcoating)
Paper
Postcard size (standard sheets)
L size (standard sheets)
Credit card size (standard sheets, full-sized label and 8-label sticker)
Wide size (100 × 200 mm (4 × 8 in.)) (standard sheets)
Paper-Feed Method Automatic feed from paper cassette
Paper-Eject Method Sheets eject onto top of paper cassette
Print Modes
Standard (1-screen) print (bordered or borderless)
Multiple (8-screen) print (for use with labels)
Print Sizes
Postcard size print
L size print
: 91.4 × 121.9 mm (3.6 × 4.8 in.)
(borderless)
: 89.0 × 119.0 mm (3.5 × 4.7 in.)
: 79.2 × 105.3 mm (3.1 × 4.2 in.)
(full-sized, borderless)
: 54.0 × 86.0 mm (2.1 × 3.4 in.)
(full-sized, bordered)
: 50.0 × 66.7 mm (2.0 × 2.6 in.)
(8 stickers per label)
: 22.0 × 17.3 mm (0.9 × 0.7 in.)
(per sticker)
(borderless)
: 100.0 × 200.0 mm (3.9 × 7.9 in.)
(bordered)
: 91.4 × 121.9 mm (3.6 × 4.8 in.)
Postcard size print
(bordered/borderless)
Approx. 63 sec.
L size print
(bordered/borderless)
Approx. 54 sec.
Credit card size print
(full-sized, bordered/
borderless)
Approx. 34 sec.
Wide size (100 × 200 mm
(4 × 8 in.)) print *1
Print
(when a Canon
camera is
connected)
: 100.0 × 148.0 mm (3.9 × 5.8 in.)
(bordered)
(bordered)
Credit card size print
Speeds*2
(borderless)
(8 stickers)
Wide size (100 × 200 mm
(4 × 8 in.)) print
Approx. 34 sec.
Approx. 78 sec.
*1 The printing area may vary depending on the camera use.
*2 The above printing speeds are applicable when Canon compact digital camera equipped with the
DIGIC II is connected to the printer. Printing speeds may vary with other cameras.
Based on Canon’s standard testing conditions. Variations may occur depending on printing.
44
† Interface
Signal Transfer
Proprietary protocol for Canon cameras, PictBridge, IrDA
Connection Method Camera connection
Interface cable included with the camera
Computer connection
Commercially available USB cable
Recommended printer cable
Material: AWG 28 or upper-grade
Type:
Twisted-pair, sealed cable
(compatible with high-speed mode)
Length: max. 5.0 m (16.4 ft.)
Phone connection
Infrared data communication
† Device Specifications
Operating
Temperatures
5 – 40 °C (41 – 104 °F)
Operating Humidity 20% to 80% (when running)
Power Source
AC 100 – 240 V (50/60 Hz)
Power consumption
AC 60 W or less (4 W or less when idle)
Dimensions
178.0 (W) × 131.0 (D) × 58.5 (H) mm (7.0 × 5.2 × 2.3 in.)
Weight
Approx. 875 g (30.8 oz.) (excluding ink and paper cassettes)
„ Compact Power Adapter CA-CP200
Input voltage
AC 100-240 V (50/60 Hz)
1.5 A (100 V) – 0.75 A (240 V)
Rated output
DC 24 V, 2.2 A
Operating temperatures
0 – 45 °C (32 – 113 °F)
Dimensions
122.0 × 60.0 × 30.5 mm (4.8 × 2.4 × 1.2 in.) (excluding cable)
Weight
Approx. 310 g (10.9 oz.)
„ Battery Pack NB-CP2L
Type
Lithium ion battery
Nominal voltage
DC 22.2 V
Nominal capacity
1200 mAh
Charge cycles
Approx. 300
Operating temperatures
5 – 40 °C (41 – 104 °F)
Dimensions
110.0 × 40.7 × 37.5 mm (4.3 × 1.6 × 1.5 in.)
Weight
Approx. 230 g (8.1 oz.)
The specifications and appearance are subject to change without notice.
45
Connecting the Printer to a Computer and Printing
Read Carefully Before Using!
CANON SOFTWARE LICENSE AGREEMENT
IMPORTANT – READ THIS AGREEMENT BEFORE USING THE SOFTWARE ON THE CD-ROM IN
THIS BOX. BY USING THE SOFTWARE, YOU AGREE TO BE BOUND BY THE TERMS OF THIS
AGREEMENT.
This is a license agreement (the “Agreement”) between you and Canon Inc. (“Canon”).
IF YOU DO NOT AGREE TO THE TERMS AND CONDITIONS OF THIS AGREEMENT, DO NOT USE
THE SOFTWARE PROGRAM ON THE CD-ROM (INCLUDING ALL SOUND AND IMAGE DATA) AND
THE USER MANUAL IN THIS BOX (COLLECTIVELY, THE “SOFTWARE”) AND PROMPTLY RETURN
THE SOFTWARE TO YOUR POINT OF PURCHASE FOR A REFUND.
In consideration of the right to use the SOFTWARE, you agree to abide by the terms and conditions
of this Agreement.
1. LICENSE: Canon grants you the personal, non-exclusive right to use the SOFTWARE only on a single
computer. You may physically transfer the SOFTWARE from one computer to another provided that the
SOFTWARE is used on only one computer at a time. You shall not install or use the SOFTWARE on a
network, multiple CPU, multiple site arrangement, or any other hardware configuration where the
SOFTWARE is accessible to more than one CPU or to more than one user.
With respect to the sound and image data (“Data”) contained in the Software, which are to be
downloaded to the applicable Canon digital camera product, Canon grants you a personal, nonexclusive license to use the Data on a single Canon digital camera product only.
YOU SHALL NOT ASSIGN, SUBLICENSE, RENT, LEASE, LOAN, CONVEY OR OTHERWISE USE,
TRANSFER, COPY, TRANSLATE, CONVERT TO ANOTHER PROGRAMMING LANGUAGE, ALTER,
MODIFY, DECOMPILE OR DISASSEMBLE THE SOFTWARE, IN WHOLE OR IN PART, EXCEPT AS
EXPRESSLY PROVIDED IN THIS AGREEMENT.
2. BACK-UP COPY: You may make one copy of the SOFTWARE solely for back-up purposes, or copy the
SOFTWARE onto the permanent storage device (e.g. a hard disk) of your computer and retain the
original for back-up purposes. Any other copying of the SOFTWARE is a violation of this Agreement.
You must reproduce and include the copyright notice on the back-up copy.
3. SUPPORT AND UPDATES: Neither Canon, nor its subsidiaries, dealers or distributors will be
responsible for providing maintenance or support for use of the SOFTWARE. No updates, fixes or
support will be made available for the SOFTWARE.
4. LIMITED WARRANTY AND LIMITATION OF LIABILITY: It is your responsibility to choose, maintain
and match the hardware and software components of your computer system. Thus Canon does not
guarantee uninterrupted service or correction of errors or that the functions or performance of the
SOFTWARE will meet your requirements. THE SOFTWARE IS LICENSED ON AN “AS IS” BASIS AND
WITHOUT WARRANTY OR CONDITION OF ANY KIND. The CD-ROM storing the SOFTWARE is
warranted only against defective material under normal use for a period of ninety (90) days after
purchase from an authorized Canon dealer as evidenced by your sales receipt. Your sole remedy for a
defective CD-ROM shall be replacement of the same without charge when returned by you at your
expense to your point of purchase and proven to be defective upon inspection. The Replacement CDROM will be warranted for the remainder of the original ninety (90) day warranty period of the defective
CD-ROM. The limited warranty does not apply if the failure of the CD-ROM resulted from accident,
abuse or misapplication of the SOFTWARE and shall not extend to anyone other than the original user
of the SOFTWARE.
EXCEPT AS SPECIFICALLY SET FORTH IN THIS PARAGRAPH 4, CANON, CANON’S
SUBSIDIARIES, DISTRIBUTORS AND DEALERS DISCLAIM ALL WARRANTIES, OR
CONDITIONS, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OR CONDITION OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE
SOFTWARE.
NEITHER CANON NOR ANY OF CANON’S SUBSIDIARIES, DISTRIBUTORS OR DEALERS IS
LIABLE FOR ANY DAMAGES HOWSOEVER CAUSED, INCLUDING WITHOUT LIMITATION,
DIRECT, CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE INCLUDING LOSS OF PROFITS,
EXPENSE OR INCONVENIENCE HOWSOEVER CAUSED OR ARISING OUT OF THE SOFTWARE
OR THE USE THEREOF.
46
NEITHER CANON, NOR ANY OF CANON’S SUBSIDIARIES, DISTRIBUTORS OR DEALERS
SHALL HAVE ANY OBLIGATION TO INDEMNIFY YOU AGAINST ANY CLAIM OR SUIT BROUGHT
BY A THIRD PARTY ALLEGING THAT THE SOFTWARE OR THE USE THEREOF INFRINGES ANY
INTELLECTUAL PROPERTY OF SUCH THIRD PARTY.
SOME STATES, PROVINCES OR LEGAL JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF
IMPLIED WARRANTIES, OR THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR PERSONAL INJURY OR DEATH RESULTING FROM
NEGLIGENCE ON THE PART OF THE SELLER, SO THE ABOVE DISCLAIMERS AND
EXCLUSIONS MAY NOT APPLY TO YOU.
5. TERM: This Agreement is effective upon your using the SOFTWARE and remains in effect until
expiration of all copyright interests in the SOFTWARE unless earlier terminated. You may terminate this
Agreement by destroying the SOFTWARE. This Agreement will also terminate without notice to you if
you fail to comply with any of the terms of this Agreement and you must then promptly return the
SOFTWARE. In addition, Canon may enforce its other legal rights.
6. U.S. GOVERNMENT RESTRICTED RIGHTS NOTICE:
The SOFTWARE is a “commercial item,” as that term is defined at 48 C.F.R. 2.101 (Oct 1995),
consisting of “commercial computer software” and “commercial computer software documentation,” as
such terms are used in 48 C.F.R. 12.212 (Sept 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R.
227.7202-1 through 227.72024 (June 1995), all U.S. Government End Users shall acquire the
SOFTWARE with only those rights set forth herein. Manufacturer is Canon Inc./30-2, Shimomaruko 3chome, Ohta-ku, Tokyo 146-8501, Japan.
7. EXPORT RESTRICTIONS: You agree to comply with all export laws and restrictions and regulations of
the country involved, and not to export or re-export, directly or indirectly, the SOFTWARE in violation of
any such laws and restrictions and regulations, or without all necessary approvals.
8. SEVERABILITY:
In the event that any provision of this Agreement is declared or found to be illegal by any court or
tribunal of competent jurisdiction, such provision shall be null and void with respect to the jurisdiction of
that court or tribunal and all the remaining provisions of this Agreement shall remain in full force and
effect.
9. CONTROLLING LAW: The terms of this Agreement as it relates to purchases of the Software in the
United States of America shall be governed and construed in all respects in accordance with the laws
and regulations of the State of New York, without reference to choice of law principles. The terms of this
Agreement as it relates to purchases of the Software in Canada shall be governed by the laws of the
province of Ontario.
10. OWNERSHIP: All rights, including but not limited to copyrights and trade secret rights, to the
SOFTWARE belong to Canon, its affiliated corporations and third party licensors. Your use of the
SOFTWARE is subject to the laws of the United States, and Canada, and other applicable copyright
and trademark laws, and nothing in this Agreement constitutes a waiver of the rights of Canon, its
affiliated corporations and third party licensors under such laws. You only own the CD-ROM media in
which the Software is stored. Except as expressly provided herein, no license or right, express or
implied, is hereby conveyed or granted by Canon to you for any intellectual property of Canon. Nothing
contained in Paragraph 1 shall be construed to give Canon any ownership rights in any images,
graphics or textual material that you save in connection with the Software.
You may not modify, remove or delete any or all copyright notices (i) which are contained in the
Software, including any copy thereof, and (ii) which are on the original CD-ROM and on the medium of
a back-up copy made pursuant to Section 2 above.
11. ACKNOWLEDGEMENT: BY USING THE SOFTWARE, YOU ACKNOWLEDGE THAT YOU HAVE
READ THIS AGREEMENT, UNDERSTOOD IT, AND AGREE TO BE BOUND BY ITS TERMS AND
CONDITIONS. YOU ALSO AGREE THAT THIS AGREEMENT IS THE COMPLETE AND EXCLUSIVE
STATEMENT OF AGREEMENT BETWEEN YOU AND CANON CONCERNING THE SUBJECT
MATTER HEREOF AND SUPERSEDES ALL PROPOSALS OR PRIOR AGREEMENTS, VERBAL
OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN THE PARTIES RELATING TO
THE SUBJECT MATTER HEREOF. NO AMENDMENT TO THIS AGREEMENT SHALL BE
EFFECTIVE UNLESS SIGNED BY A DULY AUTHORIZED OFFICER OF CANON.
47
System Requirements
Please install the software on a computer meeting the following minimum
requirements.
„ Windows
OS
Windows 98 SE (Second Edition)
Windows Me
Windows 2000 Service Pack 4
Windows XP (Including Service Pack 1 and Service Pack 2)
Computer Model
The above OS should be pre-installed on computers with built-in USB ports.
CPU
Pentium 500 MHz or higher processor
RAM
Windows 98 SE/Windows Me: 128 MB or more
Windows 2000/Windows XP: 256 MB or more
Interface
USB
Free Hard Disk
Space
• Canon Utilities
- ZoomBrowser EX: 250 MB or more
(including the PhotoRecord printing program)
- PhotoStitch: 40 MB or more
• Canon SELPHY CP600 Printer Driver: 3 MB or more
(the amount of free space required for installation)
Display
1,024 × 768 pixels/High Color (16 bit) or better
„ Macintosh
OS
Mac OS X (v10.1.5 – v10.3)
Computer Model
The above OS should be pre-installed on computers with built-in USB ports.
CPU
PowerPC G3/G4/G5
RAM
256 MB or more
Interface
USB
Free Hard Disk
Space
• Canon Utilities
- ImageBrowser: 200 MB or more
- PhotoStitch: 40 MB or more
• Canon SELPHY CP600 Printer Driver: 3.8 MB or more
(the amount of free space required for installation)
Display
1,024 × 768 pixels/32,000 colors or better
• A CD-ROM drive is required to install the software.
• Even when system requirements are met, not all computer functions can be
guaranteed.
• All procedures performed with a connection to a USB 2.0 compliant board are not
guaranteed.
• Macintosh software cannot be used on disks formatted in the UFS (Unix File
System) format.
48
Printing Operations Overview
Follow the steps outlined below to prepare the printer and install the necessary
software to enable printing and layout of images with a computer.
Prepare the printer.
Load the paper and ink cassette
into the printer.
See this guide. (p. 25 – p. 30)
Install the software and the printer driver onto
the computer.
See this guide.
Place the supplied CP Printer
Windows p. 50
Solution Disk in the computer’s
Macintosh p. 54
CD-ROM drive and install the
necessary software and the printer
driver.
Connect the printer to the computer.
Connect the printer to the
computer using a commercially
available USB cable and turn the
printer power on.
See this guide. (p. 58 – p. 59)
Print the image.
You can use the software you have
installed to print images in a variety See the Printer Software Guide*
(PDF).
of layouts.
* The Printer Software Guide will
automatically be installed to your
computer together with the
installation of the software. (p. 60)
• Please refer to the Specifications on page 44 for detailed information on USB
cables.
49
Installing the Software and the Printer Driver
The CP Printer Solution Disk contains software that your computer will require
for printing. Install the software and the printer driver according to the following
steps.
„ Windows
• Be sure to install the software and the printer driver before connecting the printer
to the computer.
• With Windows XP or Windows 2000, be sure to log on with Administrator
privileges (computer system administrator) when installing the software.
• The instructions in this section are intended for Windows XP. If you are using
another version of Windows, actual screen contents and procedures may differ
slightly from those indicated here.
1
2
50
Close any programs that are running.
Place the CP Printer Solution Disk in the CD-ROM drive.
• The installer panel automatically appears.
If the installer panel does not automatically appear, use the following procedure to
start it.
• For Windows XP, click the [Start] button and select [My Computer], double-click
the CD-ROM icon in the next window.
• For Windows 98 SE/Windows Me/Windows 2000, double-click the [My
Computer] icon on the desktop, and double-click the CD-ROM icon in the next
window.
3
Click the Application Software [Install] button and click
[Next].
Installer Panel
4
5
6
7
Select [Easy Installation] as the setup type and click [Next].
• Select [Custom Installation] to select programs for individual installation.
Click [Yes] if you consent to all the conditions of the
software license agreement.
Review the installation settings and click [Next].
• Follow the screen messages to proceed.
When a dialog box appears instructing that the installation
is complete, select [Yes, I want to restart my computer now.]
and click [Finish].
51
Next, install the printer driver to your computer.
8
Click the CP Printer Driver [Install] button.
If the installer panel does not automatically appear, use the following procedure to
start it.
• For Windows XP, click the [Start] button and select [My Computer], double-click
the CD-ROM icon in the next window.
• For Windows 98 SE/Windows Me/Windows 2000, double-click the [My
Computer] icon on the desktop, and double-click the CD-ROM icon in the next
window.
9
10
52
Click the printer you are using and click [Next].
Click [Yes] if you consent to all the conditions of the
software license agreement.
• The installer starts.
11
When the screen below appears, connect the printer to the
computer with a commercially available USB cable and turn
the printer’s power on.
• Refer to Connecting the Printer to Your Computer (p. 58) on how to connect.
• Follow the screen messages to proceed.
12
13
When a dialog box appears instructing that the installation
is complete, click [Finish].
• Restart your computer when a dialog box appears instructing you to do so.
When the computer desktop displays, remove the CP
Printer Solution Disk from the CD-ROM drive.
53
„ Macintosh
• Be sure to install the software and the printer driver before connecting the printer
to the computer.
• The instructions in this section are intended for Mac OS X (v10.3). If you are using
another version of Mac OS, actual screen contents and procedures may differ
slightly from those indicated here.
1
2
Quit any programs that are running.
Place the CP Printer Solution Disk in the CD-ROM drive, and
double-click the [Canon CP Printer Installer] icon in the CDROM.
• The installer panel automatically appears.
3
Click the Application Software [Install] button.
Installer Panel
4
5
54
Select [Easy Installation] and then click [Next].
• Select [Custom Installation] to select programs for individual installation.
Click [Agree] if you consent to all the conditions of the
software license agreement.
6
7
Review the installation settings and click [Next].
• Follow the screen messages to proceed.
When a dialog box appears instructing that the installation
is complete, click [OK].
Next, install the printer driver to your computer.
8
Click the CP Printer Driver [Install] button.
9
10
Click the printer you are using.
Click [Agree] if you consent to all the conditions of the
software license agreement.
• The installer starts.
55
11
Select [Easy Install], and then click the [Install] button.
• Follow the screen messages to proceed.
• Restart your computer when a dialog box appears instructing you to do so.
12
When the computer desktop displays, remove the CP
Printer Solution Disk from the CD-ROM drive.
Next, register your printer on the Printer List.
56
13
Connect the printer to the computer with a commercially
available USB cable and turn the printer’s power on.
14
15
Double-click the hard disk icon where Mac OS X is installed.
• For directions on connecting the printer, see Connecting the Printer to Your
Computer (p. 58).
Double-click the [Printer Setup Utility] or [Print Center] icon
in [Applications] [Utilities] folder.
• The [Printer List] window appears.
16
Click the [Add] or [Add Printer] button.
17
Select [USB], select the printer name, and then click the
[Add] button.
18
Close the window by clicking
corner.
in the upper left-hand
57
Connecting the Printer to Your Computer
„ Notes about connection
In using the USB cable, be sure to connect the printer directly to your
computer.
If you connect the USB cable via a USB hub, the printer may not function properly.
Do not use other USB devices (with the exception of a USB mouse or
keyboard) with the printer. The printer may not function properly.
Disconnect the other USB devices from your computer and then reconnect the
printer.
Do not connect two or more direct print compatible printers (all CP series
printers) to the same computer.
The printers may not function properly.
For Windows, when connecting the printer to your computer, we recommend
that you connect it to the same USB port you used to install the printer
driver.
If you connect the printer to a different USB port, Windows may create a copy of
the printer driver. This depends on your Windows version and the printer driver,
and does not affect the operation of the printer.
To delete a copy of the printer driver, proceed as follows:
1. Disconnect the USB cable from your computer.
2. Delete the copy of the printer driver as follows (do not use the uninstaller.)
(1) For Windows XP, click the [Start] button and select [Control Panel], [Printers
and Other Hardware], and [Printers and Faxes].
For Windows 98 SE/Windows Me/Windows 2000, click the [Start] button and
select [Settings], and [Printers].
(2) Right-click the copy of the printer driver and then select [Delete] on the shortcut menu.
3. Restart your computer. Connect the printer to the USB port you used to install
the printer driver.
• Do not put your computer into the standby mode (or sleep mode) while the printer
is connected to a USB port.
• If you accidentally do so, do not disconnect the USB cable from your computer
while it is in the standby mode; instead, leaving the USB cable connected, first
return your computer to its normal mode. If you remove the USB cable while your
computer is in the standby mode, your computer may not be able to return to its
normal mode. For details on your computer’s standby mode, refer to the
documentation provided with your computer.
58
1
Connect one end of a commercially available USB cable
(sold separately) to the USB port on the printer, and the
other end to a USB port on your computer.
• There is no need to turn off the printer or your computer.
• When connecting the printer to your computer, make sure the connectors on the
ends of the USB cable match the ports on the printer and your computer.
• For the location and direction of your computer’s USB port, refer to the
documentation provided with your computer.
USB port
on computer
USB cable
• When disconnecting the USB cable, you do not need to turn off the printer or your
computer.
59
Viewing the PDF Manuals
• Adobe Reader or Adobe Acrobat Reader must be installed to view the PDF
Manuals. If this software is not installed in your computer, access the following web
site and download the software.
http://www.adobe.com/products/acrobat/readstep2.html
„ Printer Software Guide
1
Install the software from the CP Printer Solution Disk.
(Windows p. 50, Macintosh p. 54)
2
Double-click
• The Printer Software Guide will automatically be installed to your computer,
[CP Printer Guide] icon appears on the desktop.
and the
[CP Printer Guide].
• Printer Software Guide will be displayed.
CP Printer Guide
• If you need the Printer Software Guide in a different language:
Windows/Macintosh: Double-click the desired language folder in the [Readme] folder
on the CD-ROM, then double-click [CP Printer User Guide.pdf].
„ ZoomBrowser EX Software User Guide/
ImageBrowser Software User Guide
To view the ZoomBrowser EX Software User Guide (Windows) and the ImageBrowser Software
User Guide (Macintosh), access the following site and download.
http://web.canon.jp/Imaging/information-e.html
60
Uninstalling the Software
This section describes how to uninstall the software.
• Uninstall the software when it is no longer needed, or if a problem occurs and
uninstalling becomes necessary. Note that if you uninstall the software, you will not
be able to use it anymore.
„ Windows
The instructions in this section are intended for uninstallation of
ZoomBrowser EX.
1
Click the [Start] button and select [Programs] or [All
Programs], [Canon Utilities], [ZoomBrowser EX], and
[ZoomBrowser EX Uninstall].
• Uninstallation begins and ZoomBrowser EX is removed.
• You can use the same procedure to uninstall PhotoStitch.
• To uninstall PhotoRecord, click the [Start] button and select [Programs] or [All
Programs], [Canon PhotoRecord], and [PhotoRecord Uninstall].
„ Macintosh
Uninstall the programs by dragging the application’s folder (the folder in which it
was installed) into the Trash, and then empty the Trash.
• Please be careful not to accidentally delete any folders with downloaded images
that may be contained within the application folder.
61
Uninstalling the Printer Driver
This section describes how to uninstall the printer driver.
• Uninstall the printer driver if it is no longer needed, or if a problem occurs and
uninstalling becomes necessary. Note that if you uninstall the printer driver, you
will no longer be able to use the printer to print.
Be sure to follow the procedures described in this section to uninstall the printer.
„ Windows
62
1
Click the [Start] and select [Programs] or [All Programs],
[Canon SELPHY CPXXX], [Uninstall].
2
Select the printer you will uninstall and click [Next].
• Follow the screen messages to proceed.
„ Macintosh
1
2
Place the CP Printer Solution Disk in the CD-ROM drive, and
double-click the [Canon CP Printer Installer] icon.
3
4
5
Click the printer you wish to uninstall.
• The installer panel appears.
Click the CP Printer Driver [Install] button.
Click [Agree] if you consent to all the conditions of the
software license agreement.
Select [Uninstall], and then click the [Uninstall] button.
• Follow the screen messages to proceed.
63
6
When the uninstallation is complete, click [Quit], and then
remove the CP Printer Solution Disk from the CD-ROM
drive.
Next, delete the printer from the Printer List.
64
7
8
9
Double-click the hard disk icon where Mac OS X is installed.
10
Close the window by clicking
corner.
Double-click the [Printer Setup Utility] or [Print Center] icon
in [Applications] [Utilities] folder.
• The [Printer List] window appears.
Select the printer you uninstalled, and then click the
[Delete] button.
in the upper left-hand
Printing with Non-Canon Digital Cameras
Since the CP600 printers support the direct print PictBridge* standard, you can
connect PictBridge compliant non-Canon digital cameras to easily print high
image quality photos.
* PictBridge: PictBridge is an industry standard for direct printing that allows you to print
images without using a computer by directly connecting a digital camera or digital camcorder
(hereafter “camera”) to a printer, regardless of their brands and models.
„ Before Using the Printer
Please read carefully the user guide that came with your camera and make sure
that:
• The camera is PictBridge compliant.
• You are using the USB cable for the camera/computer connection to connect the printer to
the camera. (This cable may be included with the camera)
• You set the print settings with the camera. For details, refer to the camera’s user guide.
„ Connecting the Camera
Insert one end of the USB cable used for the camera/computer connection in the
printer’s direct print port (see p. 29) and insert the other end in the camera’s
terminal. (For details, refer to the camera’s user guide)
• The printer’s indicator blinks green several times once the printer and camera are correctly
connected. The indicator lights steadily green once it is ready to print.
• If a problem occurs during a connection or during printing, the printer’s indicator lights or
blinks red. If this happens, the error message that appears on the camera’s LCD monitor
may differ according to your camera model.
• Printing speed may differ according to your camera model and the image’s number
of recorded pixels. (The value written on page 44 is a printing speed obtained
when printing with a Canon camera.)
65
Disclaimer
• While every effort has been made to ensure that the information contained in this guide is
accurate and complete, no liability can be accepted for any errors or omissions. Canon reserves
the right to change the specifications of the hardware and software described herein at any time
without prior notice.
• No part of this guide may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language in any form, by any means, without the prior written permission
of Canon.
• Canon makes no warranties for damages resulting from corrupted or lost data due to a
mistaken operation or malfunction of the camera, the printer, the software, the CompactFlashTM
cards (CF cards), personal computers, peripheral devices, or use of non-Canon CF cards.
Trademark Acknowledgments
•
•
•
•
Canon and SELPHY are trademarks of Canon Inc.
Adobe is a trademark of Adobe Systems Incorporated.
CompactFlash is a trademark of SanDisk Corporation.
Macintosh, Mac OS and QuickTime are trademarks of Apple Computer Inc., registered in the
United States and other countries.
• Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
• Other names and products not mentioned above may be registered trademarks or trademarks
of their respective companies.
66
Download PDF