Euphonix | DF66 | Euphonix Reboot Procedures

Euphonix Max Air QUICK System Reboot Procedures
CNN Los Angeles
Updated:2/17/2012
**SAVE TITLE IF NEEDED**
**ALL UNSAVED INFORMATION WILL BE LOST**
1) Restart the System Computer
a) Hit the SYSTEM button on the right side of the Max Air Application
b) Within the SYSTEM page, go to the ABOUT tab.
c) Tap the SHUTDOWN button, and then select EXIT TO OPERATING
SYSTEM. Then press OK.
This is just for Reference:
i) RESTART- this will just restart the application.
ii) EXIT TO OPERATING SYSTEM - will close the Max Air Application and bring you to
the desktop.
d) Once on the DESKTOP, go to the START MENU then select
SHUTDOWN.
i) In the Shutdown window, make sure RESTART is selected, then click
OK.
1 of 6
Euphonix Max Air QUICK System Reboot Procedures
CNN Los Angeles
Updated:2/17/2012
****IF FULL REBOOT IS NEEDED REFER TO PAGE #7****
**NEXT STEPS NEED TO BE DONE QUICKLY.**
**READ THROUGH BEFORE STARTING**
2) REBOOT THE MODULES
a) Once back at the Desktop, double-click on the SHORTCUT TO
EUPHONIX.cpl
i) This will open the DF-66 (Processing Cores) control panel
2 of 6
Euphonix Max Air QUICK System Reboot Procedures
CNN Los Angeles
Updated:2/17/2012
b) RESTART CORE #1
i) Select the First DF-66 in the list (DF-66 ACR-1 on the ACR console)
ii) Hit PROPERTIES
iii) Then go to the DIAGNOSITCS tab
iv) Then hit RESTART
v) Then hit YES to restart the DF-66 Application
vi) Then Hit OK to go back to the main control panel page.
c) RESTART CORE #1-A
i) Repeat the restart in the second core in the list (DF-66 ACR-1A on the
ACR console)
3 of 6
Euphonix Max Air QUICK System Reboot Procedures
CNN Los Angeles
Updated:2/17/2012
d) REBOOT THE MIXER MODULES
i) Under the leather padding and to the left side of each of the 3 mixer
sections (2 on the MOPS console), there is a surface reboot button.
ii) Press each button once. The Surface will clear and the First two
channel label screens in each module will say “Please Wait…”
4 of 6
Euphonix Max Air QUICK System Reboot Procedures
CNN Los Angeles
Updated:2/17/2012
3) OPEN MAX AIR application
a) On the Desktop Open the MAX AIR icon.
i) This will open the software, and take you to a loading screen.
b) Once it gets to a screen that has all the different modules on it, wait for all
to load.
i) You will see 7 items loading
(1) System PC
(2) VIF Pilot
(3) Pilot 1
(4) Pilot 1-A
(5) 416
(6) 416
(7) 404
c) ONCE ALL HAVE LOADED TO 100% YOU CAN CLICK CONTINUE
i) ***DO NOT HIT “SET AS DEFAULT”***
4) LOAD THE TITLE
a) Load the title you need. And the system should be working.
5 of 6
Euphonix Max Air QUICK System Reboot Procedures
CNN Los Angeles
Updated:2/17/2012
THINGS TO REMEMBER AFTER REBOOT
1) ALL MONITOR VOLUMES WILL BE AT “0”
a. The volumes for the main control speakers, the ACR speakers, and
the ACR solo speakers, will all be set to OFF and will be MUTED
when the console comes back up.
b. To set this back to normal:
i. Turn the CONTROL ROOM level to -30.0 (85) and make the
the CUT button is not lit up.
ii. In the volume bus called MONITORS (right above the
CONTROL ROOM volume knob) turn the bottom knob all
the way up, and tap the knob to make it go solid.
-
 Look right after reboot
 With Volumes Set
6 of 6
Euphonix Max Air QUICK System Reboot Procedures
CNN Los Angeles
Updated:2/17/2012
REFER TO THIS PAGE IF FULL SYSTEM REBOOT
IS NEEDED
1) Complete Page 1 as noted
2) Once the Computer has been shut down turn off ALL the
power switches on the mixer surface.
a. There are two switches on EACH mixer module. (6 on
ACR console, 4 on MOPS)
3) Once the surface is off, head up to TGR
a. Turn all the DF-66 Processing computers (two bottom
Euphonix Computers in each rack)
i. Turn them off by pushing the power button briefly.
The unit will power down after about 30 seconds. IF
NOT hold the power button until it turns off.
4) Once all three computers are off reboot them starting with the
System computer (top unit of the 3) followed by the DF-66
processing comps.
5) At this point refer back to page 5.
a. NOTE: It might be easier to pull up the system computer
on KVM in TGR to make sure the DF-66’s (Pilot 1 and 1A) come back online before you return to the control
room.
b. REMEMBER: DO NOT push continue on the max air
status screen until ALL computer and modules are online
and READY. Refer to page 5 to confirm this.
6) Once you return to the ACR or MOPS console you can turn the
surface back on. The modules will come back online and once
all comps and modules are online hit CONTINUE and than load
the default title.
DEFAULT TITLES
ACR
Folder: A_LA DEFAULTS
Title: A_STU_DEFAULT
MOPS
Folder: MOPS Titles
Titles: MOPS_DEFAULT
7 of 6
Download PDF