Comfort Glow CVDR30 Installation manual

TM
GAS LOG REMOTE READY
VENTED DECORATIVE APPLIANCE
OWNER'S OPERATION AND INSTALLATION MANUAL
Convertible from Natural
Gas to Propane/LP Gas
VANGUARD MODELS:
VVSA18R, VVSA24R, VVDA18R, VVDA24R and VVDA30R
FOR USE WITH LOG SETS:
Hanover Round Oak Log Models VSLR18 and VSLR24
Kingston Split Oak Log Models VDLCR18, VDLCR24 (Shown)
and VDLCR30
FMI MODELS:
FVSA18R, FVSA24R, FVDA18R, FVDA24R and FVDA30R
FOR USE WITH LOG SETS:
Arlington Round Oak Log Models FSLR18 and FSLR24
Manchester Split Oak Log Models FDLCR18, FDLCR24 and
FDLCR30
COMFORT GLOW MODELS:
ANSI Z21.60a-2000
CSA 2.26a-2000
Berkshire Oak Log Models CVDA18R, CVDA24R and
CVDA30R
Amherst Oak Log Models CPVSA18R and CPVSA24R
APPROVED
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
— Installation and service must be performed by a
qualified installer, service agency, or the gas supplier.
WARNING: Improper installation,
adjustment, alteration, service, or
maintenance can cause injury or
property damage. Refer to this
manual for correct installation and
operational procedures. For assistance or additional information
consult a qualified installer, service agency, or the gas supplier.
WARNING: This appliance is for
installation only in a solid-fuel
burning masonry or UL127 factorybuilt fireplace, constructed of noncombustible material, and connected to a working flue. (See page
4 for minimum flue opening.)
WARNING: This is a gas-fired appliance. It uses air (oxygen) from the room in which it is installed.
Provisions for adequate combustion and ventilation air must be provided. Refer to the National
Fuel Gas Codes, ANSI Z233.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation.
Save this manual for future reference.
2
TABLE OF CONTENTS
SAFETY INFORMATION
TABLE OF CONTENTS
SAFETY INFORMATION ............................................................ 2
CLEANING AND MAINTENANCE ............................................ 12
LOCAL CODES ........................................................................... 3
REPLACEMENT PARTS .......................................................... 12
PRODUCT IDENTIFICATION ..................................................... 3
TROUBLESHOOTING .............................................................. 13
UNPACKING ............................................................................... 3
ILLUSTRATED PARTS BREAKDOWN AND PARTS LIST ....... 16
PRODUCT FEATURE ................................................................. 3
ACCESSORIES ........................................................................ 28
INSTALLATION ........................................................................... 4
OWNER'S REGISTRATION FORM .......................................... 29
OPERATING APPLIANCE ........................................................ 10
WARRANTY INFORMATION ...................................... Back Cover
INSPECTING BURNERS .......................................................... 12
SAFETY INFORMATION
WARNING ICON
G 001
WARNINGS
1.
WARNING: This product contains chemicals
known to the State of California to cause cancer or
birth defects, or other reproductive harm.
2.
WARNING: Keep flue open when operating unit.
IMPORTANT: Read this owner’s manual carefully and
completely before trying to assemble, operate, or service this log set. Improper use of this log set can cause
serious injury or death from burns, fire, explosion,
electrical shock, and carbon monoxide poisoning.
3.
DANGER: Carbon monoxide poisoning may lead
to death!
4.
Carbon Monoxide Poisoning: Early signs of carbon monoxide
poisoning resemble the flu, with headaches, dizziness, or nausea. If
you have these signs, the log set may not be working properly. Get
fresh air at once! Have log set serviced. Some people are more
affected by carbon monoxide than others. These include pregnant
women, people with heart or lung disease or anemia, those under the
influence of alcohol, and those at high altitudes.
5.
Natural and Propane/LP Gas: Natural and propane/LP gases are
6.
odorless. An odor-making agent is added to the gas. The odor helps
you detect a gas leak. However, the odor added to the gas can fade.
Gas may be present even though no odor exists.
Make certain you read and understand all warnings. Keep this
manual for reference. It is your guide to safe and proper operation
of this log set.
7.
8.
WARNING: Any change to this log set or its
controls can be dangerous.
This appliance, as supplied, is only for use with the type of gas
indicated on the rating plate. This appliance is convertible for
use with propane/LP.
If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use any phone in
your building
• immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions
• if you cannot reach your gas supplier, call the fire department
Never install the log set
• in a recreational vehicle
• where curtains, furniture, clothing, or other flammable objects are less than 42 inches from the front, top, or sides of
the log set
• in high traffic areas
• in windy or drafty areas
Before installing in a solid fuel burning fireplace, the chimney
flue and firebox must be cleaned of soot, creosote, ashes and
loose paint by a qualified chimney cleaner. Creosote will ignite if highly heated. Inspect chimney flue for damage.
You must operate this log set with fireplace doors or screens in
place and fully closed. Unless provided by other means, fireplace doors or screens shall have openings for introduction of
combustion air.
This log set is designed to be smokeless. If logs ever appear to
smoke, turn off appliance and call a qualified service person.
Note: During initial operation, slight smoking could occur due
to log curing and the burning of manufacturing residues. You
may wish to add more ventilation by opening a window.
To reduce the creation of soot, follow the instructions in Cleaning and Maintenance, page 12.
Do not allow fans to blow directly into the fireplace. Avoid
any drafts that alter burner flame patterns. Ceiling fans can
create drafts that alter burner flame patterns. Altered burner
patterns can increase sooting.
For more information, visit www.desatech.com
901273-01D
SAFETY INFORMATION
LOCAL CODES
PRODUCT IDENTIFICATION
UNPACKING
PRODUCT FEATURE
SAFETY INFORMATION
PRODUCT IDENTIFICATION
Continued
12.
16.
17.
18.
LOCAL CODES
Burner
Manifold
Figure 1 - Product Identification (FVDA24R Shown)
Hearth Kit Model ________________________
Serial Number __________________________
Log Set Model __________________________
UNPACKING
CAUTION: Do not remove the metal data plates
from the burner pan. The data plates contain important warranty and safety information.
1.
2.
Remove logs, hearth kit, pan materials, and hardware
from carton.
Remove all protective packaging applied to logs and base
for shipment.
Check all items for any shipping damage. If damaged, promptly
inform dealer where you bought the product.
Install and use log set with care. Follow all local codes. In the absence
of local codes, use the latest edition of The National Fuel Gas Code
ANSI Z223.1/NFPA 54*.
3.
*Available from:
PRODUCT FEATURE
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
REMOTE READY SAFETY VALVE/PILOT
This unit is provided with a milivolt remote ready control valve
which may be connected to optional remote accessories for wall
switch or wireless operation (see Accessories, page 28).
Unit is tested and approved to ANSI Z21.60a-2000 and CSA 2.26a2000 as a vented decorative appliance. It is supplied with the parts and
instructions to convert to propane/LP gas use.
For more information, visit www.desatech.com
901273-01D
P
15.
Burner
Clamp
FF
14.
Burner
Pan
O
13.
Grate
N
11.
Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this log set.
The installation and provisions for combustion and ventilation
air must conform with the National Fuel Gas Codes, ANSI Z233.1/
NFPA 54, Section 5.3, Air for Combustion and Ventilation.
Do not run log set
• where combustible materials, gasoline and other flammable
vapors and liquids are used or stored
• under dusty conditions
Do not burn solid fuel in the fireplace after installing the log
set. Do not use this log set to cook food or burn paper or other
objects.
Log set becomes very hot when in use. Keep children and adults
away from hot surface to avoid burns or clothing ignition. Log
set will remain hot for a time after shut-down. Allow surface
to cool before touching.
Carefully supervise young children when they are in the room
with log set.
Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
To help prevent breakage, new logs must be broken-in (see
Curing Logs page 11).
Turn log set off and let cool before servicing, installing, or
repairing. Only a qualified service person should install, service, or repair log set.
Provide adequate clearances around air openings.
O
10.
Grate Steps
ILOT
9.
3
3
4
INSTALLATION
Flue Opening Specifications
Check Gas Type
Venting Specifications for Installation
INSTALLATION
WARNING: The Massachusetts State Board requires all installations be performed by a Licensed
Plumber or Gas Fitter. Massachusetts state code requires all vent dampers be welded open or removed.
CAUTION: Do not remove the data plates attached to the burner pan. The data plates contain
important warranty and safety information.
WARNING: Before installing in a solid fuel burning
fireplace, the chimney flue and firebox must be cleaned
of soot, creosote, ashes and loose paint by a qualified
chimney cleaner. Creosote will ignite if highly heated.
A dirty chimney flue may create and distribute soot
within the house. Inspect chimney flue for damage.
NOTICE: Installation, service, and repair of this appliance must be performed by a qualified installer,
service agency, company or gas supplier experienced with this type of gas appliance. Only factory
authorized components listed in these instructions
may be used in accordance with the manufacturer’s
instructions and all codes and requirements of the
authority having jurisdiction. Any modifications to
this kit, or use of unauthorized components or accessory items will void the manufacturer’s warranty, and
may result in a hazardous condition.
FLUE OPENING SPECIFICATIONS
Note: This vented appliance must be installed only in a solid-fuel
burning fireplace with a working flue and constructed of noncombustible material.
The charts in Figure 2 indicate technical information regarding the
installation of your gas log set. Please make sure that all of the
specifications shown are applicable before installation is attempted.
The fireplace must include a working flue and venting system with
the minimum openings shown in the Figure 2.
CHECK GAS TYPE
Use only natural gas. If your gas supply is not natural gas, you must
convert the appliance to propane/LP. Follow the instructions on page 7.
If the fireplace does not have a gas supply shutoff valve, one must
be installed.
VENTING SPECIFICATIONS FOR
INSTALLATION
The fireplace chimney flue and vent must be drafting properly. To
check the vent for proper drafting: Light a tightly rolled newspaper
on one end and place it at the inside front edge of the fireplace.
Observe the smoke and be sure the vent is properly drawing it up the
chimney. If the smoke spills out into the room, extinguish the flame
and remove any obstruction until proper venting is achieved.
The chimney flue damper must be fixed open to provide a minimum
of 81 sq. in. of free air opening during operation of this log set. A
multipurpose damper clamp is provided to fix the damper in position.
The minimum flue sizes shown in Figure 2 are based on a 6'
chimney height using round pipe. Your minimum flue size will
vary based on input rate and chimney height. Refer to the National
Fuel Gas Code ANSI Z223.1/NFPA 54, Section 6.6, for details.
BURNER ORIFICE
LOG
SIZE
18" SA/DA
24" SA
24" DA
30" SA/DA
NATURAL
PROPANE/LP
IN. NUM. COLOR
IN. NUM. COLOR
.129
30
Green
.073
49
Red
.141
28
Yellow
.086
44 Orange
.136
29 White/Yellow .086
44 Orange
.157
22 Yellow/Blue .089
43
Black
MINIMUM FIREBOX SIZES
LOG FRONT BACK
MINIMUM
SIZE WIDTH WIDTH* DEPTH HEIGHT FLUE SIZE
18"
34"
16"
14"
18"
8" dia.
24"
35 3/4"
17"
15 1/2"
18"
8" dia.
30"
42"
27"
18"
18"
9" dia.
FUEL PRESSURE
SPECIFICATIONS (W.C.)
Inlet
Manifold*
NG
5.5"-10.5"
3.5"
LP
11"-13"
10"
* ± .2"
Btu Input Btu Input
Natural Propane/LP
DESCRIPTION
Gas
Gas
18" Single Burner 50,000
40,000
24" Single Burner 60,000
50,000
18" Dual Burner
55,000
45,000
24" Dual Burner
65,000
55,000
30" Dual Burner
70,000
60,000
*At depth indicated
Figure 2 - Technical Information Charts
For more information, visit www.desatech.com
901273-01D
INSTALLATION
Installing Damper Clamp
Connecting to Gas Supply
5
5
INSTALLATION
Continued
INSTALLING DAMPER CLAMP
Secure the damper stop clamp provided to the leading edge of the
damper as shown in Figure 3. If for any reason this clamp doesn't
work on your fireplace, another suitable clamp or permanent stop
must be installed, or the damper blade must be cut or removed.
Damper Clamp
Installation must include an equipment shutoff valve with "T" style
handle, gas union and, for propane/LP gas only, a plugged 1/8" NPT
tap. Locate NPT tap within reach for test gauge hook up. NPT tap
must be upstream from log set (see Figure 4).
IMPORTANT: Install equipment shutoff valve in an accessible
location. The equipment shutoff valve is for turning on or shutting
off the gas to the appliance.
Apply pipe joint sealant lightly to male NPT threads. This will
prevent excess sealant from going into pipe. Excess sealant in pipe
could result in a clogged burner injector.
Damper
Damper
Manufactured
Fireplace
Masonry Fireplace
Damper
Clamp
Damper
WARNING: Use pipe joint sealant that is resistant
to liquid petroleum (LP) gas.
We recommend that you install a sediment trap in the supply line as
shown in Figure 4. Locate sediment trap where it is within reach for
cleaning. Install in piping system between fuel supply and heater.
Locate sediment trap where trapped matter is not likely to freeze. A
sediment trap traps moisture and contaminants. This keeps them
from going into log set controls. If sediment trap is not installed or
is installed wrong, log set may not run properly.
Approved Flexible Gas Hose (no longer
than 36" if required by local codes)
Figure 3 - Attaching Damper Clamp
CONNECTING TO GAS SUPPLY
WARNING: A qualified service person must connect log set to gas supply. Follow all local codes.
Installation Items Needed
Before installing log set, make sure you have the items listed below.
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve
• adjustable (crescent) wrench or pliers
• sediment trap
• tee joint
• pipe wrench
CSA Design-Certified
Equipment Shutoff Valve
With 1/8" NPT Tap*
From Gas Meter
(5" W.C.** to
10.5" W.C.
Pressure)
3" Minimum
Cap
Pipe Nipple Tee Joint
Sediment Trap
Figure 4 - Gas Connection
* Purchase the optional CSA design-certified equipment shutoff
valve from your dealer. See Accessories, page 28.
** Minimum inlet pressure for purpose of input adjustment.
CAUTION: Use only new, black iron or steel pipe.
Internally-tinned copper tubing may be used in certain
areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to log set. If
pipe is too small, undue loss of volume will occur.
For more information, visit www.desatech.com
901273-01D
6
INSTALLATION
Checking Gas Connections
Hearth Kit Installation
INSTALLATION
Continued
Pressure Testing Gas Supply Piping System
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
1.
2.
3.
4.
Gas
Connector
Tube
FF
O
P
5.
6.
Disconnect log set and its individual equipment shutoff valve
from gas supply piping system.
Cap off open end of gas pipe where equipment shutoff valve
was connected.
Pressurize supply piping system by either using compressed
air or opening main gas valve located on or near gas meter.
Check all joints of gas supply piping system. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show
a leak.
Correct all leaks at once.
Reconnect log set and equipment shutoff valve to gas supply.
Check reconnected fittings for leaks.
N
WARNING: Never use an open flame to check for
a leak. Apply a noncorrosive leak detection fluid to all
joints. Bubbles forming show a leak. Correct all leaks
at once.
If using propane/LP gas, see Propane/LP Gas Conversion on page
7, before installing hearth pan.
1. Place the burner pan assembly in the center of the fireplace
floor. Make sure the front of pan faces forward.
2. Thread the gas supply fitting to the fireplace gas supply pipe.
Adjust to most convenient position.
3. Install the gas connector tube to the gas supply adapter. Carefully
shape tube and attach to gas inlet fitting (see Figure 6). Be
careful not to cause kinks in tube.
4. Test for leaks following instructions under Testing Burner for
Leaks, page 8.
5. Retighten and adjust the location of the gas control as necessary.
The gas control should be level, with the control rod to the front.
O
WARNING: Test all gas piping and connections
for leaks after installing or servicing. Correct all leaks
at once.
HEARTH PAN INSTALLATION
ILOT
CHECKING GAS CONNECTIONS
Gas Control Valve
Gas Inlet
Fitting
Inlet Opening
Figure 6 - Installing Inlet Fitting and Gas Connector Tube (Valve
Cover Removed for Clarity)
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
1.
2.
3.
4.
Close equipment shutoff valve (see Figure 5).
Pressurize supply piping system by either using compressed
air or opening main gas valve located on or near gas meter.
Check all joints from gas meter to equipment shutoff valve
(see Figure 5). Apply a noncorrosive leak detection fluid to all
joints. Bubbles forming show a leak.
Correct all leaks at once.
Equipment Shutoff Valve
Gas Meter
Figure 5 - Checking Gas Joints
For more information, visit www.desatech.com
901273-01D
INSTALLATION
Hearth Kit Installation (Cont.)
7
7
INSTALLATION
Continued
Propane/LP Gas Conversion
To convert to propane/LP gas, the regulator pressure must be reset.
Also, the burner inlet fitting and pilot orifice must be replaced. The
propane/LP burner inlet fitting is supplied with the orifice installed for
your log set.
Burner Inlet Fitting
1. Remove the pilot assembly from the valve cover by removing
the two screws on the bracket (see Figure 7).
2. Unscrew and remove piezo ignitor and ignitor cover from
valve cover.
3. Remove the two (2) screws on the burner pan and the remaining
screw on the rear of the control valve to remove valve cover.
4. Unthread control valve and burner inlet fitting from burner tube
by turning valve counter-clockwise (see Figure 8) .
5. Remove natural gas inlet fitting from the control valve and
discard (see Figure 8). DO NOT remove the orifice from this
fitting. The propane/LP burner inlet fitting is included in the
hardware kit (see Figure 11, page 8).
Thermocouple
Pilot
Bracket
Assembly
Screw
Burner Pan
Ignitor
6.
Be sure to use the correct orifice for your appliance. The orifice
kit included with this appliance contains an orifice installed in
an air mixer fitting.
7. Using thread sealant (resistant to the action of propane/LP gas)
on smaller end of fitting, screw the burner inlet fitting into the
outlet side of the gas control. Tighten using a wrench.
8 . Rethread the valve and fitting assembly into the burner tube
until fully threaded and level with the burner pan. Reattach the
valve cover with the three (3) screws previously removed in
step 3.
Injector for
Natural
Gas
Injector for
Propane/LP
Gas
NATURAL
GAS FITTING
PROPANE/LP
GAS FITTING
Figure 9 - Burner Inlet Fittings with Injectors
Adjusting Regulator Pressure For Propane/LP Conversion
1. Locate the pressure button on regulator tower of gas control valve.
2. Remove the pressure button from the regulator tower (see
Figure 10).
3. Reverse the pressure button and replace into regulator tower
(see Figure 11).
Gas Control Valve
P
FF
O
P
Valve
Cover
Piezo Ignitor
Figure 7 - Removing/Installing Thermocouple, Pilot, and Piezo
Ignitor Cover
N
N
Machine
Screw
O
N
ILOT
O
P
FF
O
Piezo Ignitor
Cover
Regulator
Tower
Figure 10 - Removing Pressure Button
ILOT
O
FF
O
Pressure
Button
Gas Control Valve
ILOT
Pressure
Button
P
ILOT
N
O
N
O
FF
O
P
ILOT
Figure 8 - Remove Burner Inlet Fitting
Figure 11 - Replacing the Pressure Button in the Propane/LP
position
For more information, visit www.desatech.com
901273-01D
FF
O
Regulator
Tower
Burner Inlet Fitting
for Natural Gas
8
INSTALLATION
Hearth Kit Installation (Cont.)
Remote Control Options
Testing Burner for Leaks
Adding Pan Material
INSTALLATION
Continued
Changing Pilot Orifice
GWMS2
The pilot is provided with a natural gas orifice installed. For
propane/LP gas you must remove it and replace it with a propane/LP
orifice. The hardware kit contains an propane/LP orifice with a red
stripe for converting the pilot.
1. Gently loosen and remove the pilot line connection from the
bracket (see Figure 12).
2. Replace the orifice (see Figure 12) with the propane/LP pilot
orifice with the red stripe.
3. Replace and tighten the pilot line to the bracket.
4. Reattach the pilot and piezo ignitor assembly to the valve cover
with the screws previouly removed (see Figure 7, page 7).
Note: Follow the instructions under the section, Testing Burner
for Leaks.
When installing the GWMS2 remote wall switch option, follow all
instructions included with the accessory. Connect wires as shown in
Figure 13. You will need to route the wiring away from the gas control
and log set in a way which prevents direct radiant heat on the wires.
No Optional Accessories
If you choose no remote accessories at this time, the provided jumper
wire must be installed to the terminal block on the gas control.
Connect the lead to the fast-on terminals marked TH and TPTH.
TESTING BURNER FOR LEAKS
1.
Generously apply soapy solution to all connections.
WARNING: Never check for gas leaks with
open flame.
2.
Pilot
Orifice
Figure 12 - Installing Propane/LP Pilot Orifice
3.
REMOTE CONTROL OPTIONS
GHRC
If you are using the GHRC remote control option, you must first
connect the leads of the receiver to the terminal block on the gas
control (see Figure 13).
1. Connect the leads to the male fast-on terminals marked TH
and TPTH.
2. Install a 9V battery (refer to the instructions included with the
GHRC).
3. Install a 9V battery into the hand-held transmitter.
4. Insert the receiver into the simulated log control cover, with
the raised cylinder fitting into the hole in the cover.
5. The cover may be moved aside when operation of the gas control is necessary.
4.
5.
ADDING PAN MATERIAL
1.
2.
Control
Valve
Light the burner with the shutoff valve no more than half open
and holding a match slightly in front of the pan (see Lighting
Instructions, page 10).
Inspect all connections for bubbles, raw gas odor, or flame
from any area other than the burner (leaks). If leaks are detected, shut off the gas valve immediately. Tighten, or reassemble the loose connection(s) using pipe joint compound until
burner system is leak free.
When the burner is tested and leak free, observe the individual
tongues of flame on the burner. Note: The burner design includes more ports on the outside of the bar. Make sure that all
ports are clear and producing flame evenly across the burner.
If any ports appear blocked, clear them by removing the burner
manifold and reaming the ports with a modified paper clip or
other suitable tool.
When finished testing, turn the gas shutoff valve OFF to extinguish all flames.
Open the bag of ash bed material (vermiculite) and spread it evenly
across the burner pan to the top. You may overflow the front and
sides of the pan to cover the entire pan. Do not cover valve.
Open the glowing embers and evenly cover the ash bed material (vermiculite) in the burner pan.
Fast-On
Terminals
Figure 13 - Connecting Wire Terminals
For more information, visit www.desatech.com
901273-01D
INSTALLATION
Installing Grate and Logs
9
9
INSTALLATION
Continued
INSTALLING GRATE AND LOGS
5.
P
Figure 16 - Placement of Top Logs (Manchester Split Oak Logs
Shown)
N
O
FF
O
P
ILOT
Figure 14 - Installing Grate (Pan Material Not Shown)
N
O
FF
O
P
ILOT
N
O
FF
O
P
ILOT
Manchester Split Oak Logs
Arlington Round Oak Logs
Figure 15 - Installing Front and Back Logs (Number and style of
your logs may vary)
For more information, visit www.desatech.com
901273-01D
FF
O
Grate Steps
Grate
N
3.
4.
O
2.
Place the grate over the burner pan where the two outer horizontal supports on the grate fit into the two pan positioning
notches in the rear vertical edge of the pan.
Slide the two rear log grate steps over the two outer horizontal
supports on the grate as shown in Figure 14.
Place the back log on the grate onto the grate steps (see Figure 15).
Place the front log(s) on the grate and slide forward against
the front bars on the grate (see Figure 15).
Place the smaller top logs onto the bottom logs (see Figure 16).
Leave as much open space between logs as possible to minimize flame impingement and sooting. Note: Logs may chip if
they are handled roughly or if hit together while being placed.
ILOT
1.
10
OPERATING APPLIANCE
For Your Safety Read Before Lighting
Lighting Instructions
OPERATING APPLIANCE
6.
Note: You may be running this log set for the first time
after hooking up to gas supply. If so, the control knob may
need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.
WARNING: Keep flue open when operating unit.
With control knob pressed in, press and release ignitor button. This will light pilot. Visually locate the pilot on the control valve cover by the edge of the burner pan to look for flame.
If needed, keep pressing ignitor button until pilot lights.
If the pilot will not stay lit after several tries, turn the gas
control knob to "OFF" and call your service technician or
gas supplier.
8.
Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob.
• If control knob does not pop out when released, contact
a qualified service person or gas supplier for repairs.
Note: If pilot goes out, repeat steps 4 through 8.
9. Slightly push in and turn control knob counterclockwise
to the ON position.
10. If Using Optional Hand-Held Remote or Wall Switch:
Wait one minute and switch selector switch to the ON position to light burner.
Ignitor
Button
Control
Knob
OFF
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result
in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
7.
ON
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
Press in and turn control knob counterclockwise
to the PILOT position. Press in control knob for five (5)
seconds (see Figure 17).
OT
PIL
FOR YOUR SAFETY READ
BEFORE LIGHTING
LIGHTING INSTRUCTIONS
1.
2.
3.
STOP! Read the safety information, above.
Make sure equipment shutoff valve is fully open.
If Using Optional Hand-Held Remote or Wall Switch:
Set switch to OFF position.
WARNING: Burner will come on automatically
within one minute when the selector switch is in the
ON position after the pilot is lit.
4.
Press in and turn control knob clockwise
OFF position.
5.
Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information, above. If you don’t smell
gas, go to the next step.
Figure 17 - Control Knob and Ignitor Button Location (Shown as
Supplied, No Control Options)
Thermocouple
Pilot
Burner
to the
Figure 18 - Thermopile and Pilot
For more information, visit www.desatech.com
901273-01D
OPERATING APPLIANCE
To Turn Off Gas To Appliance
Curing Logs
Optional Remote Operation
GWMS2 Wall Mounted Switch
11
11
OPERATING APPLIANCE
Continued
OPTIONAL REMOTE OPERATION
TO TURN OFF GAS TO APPLIANCE
Shutting Off Appliance
Slightly push in and turn control knob clockwise
OFF position.
to the
Note: All remote control accessories must be purchased separately. Follow instructions included with the remote control.
NOTICE: You must light the pilot before using the handheld remote control unit. See Lighting Instructions,
page 10.
Shutting Off Burner Only (pilot stays lit)
You may shut off the burner and keep the pilot lit by doing one
of the following:
1. Slightly push in and turn control knob clockwise
to the PILOT position.
2. If Using Optional Hand-Held Remote or Wall Switch:
Set switch to OFF position.
1.
CURING LOGS
During the 2-3 hour appliance break-in period, you may detect
an odor from the appliance as the various paints and compounds used in the manufacturing of this log set cure. This is a
normal and temporary situation that is not cause for alarm.
However, you may want to provide extra ventilation to the room
during this time.
To ensure proper curing of the logs:
• Ignite a 2" flame and maintain it for 1 hour.
• Burn the logs in consecutive 1 hour periods raising the flame
an additional 2" to full flame height for a total of three hours.
After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Slide the selector switch
to the REMOTE position. Note: The burner may light if
hand-held remote ON button was on when selector switch
was last turned off. You can now turn the burner on and
off with the hand-held remote control unit.
IMPORTANT: Do not leave the selector switch in the REMOTE position when the pilot is not lit. This will drain the
battery.
IMPORTANT: Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
GHRC Operation:
2.
Press the ON/OFF button to turn the burner on and off.
When turning burner off, the pilot will remain lit.
GWMS2 WALL MOUNTED SWITCH
(OPTIONAL)
This wall switch works just like the conventional light switch.
Flip the switch up for on and down for off.
Note: Make sure that this switch is not in a position to be
mistaken for a light switch. This may result in the log set being
inadvertently turned on without the proper precautions being
taken. See installation instructions on page 8 of this manual.
For more information, visit www.desatech.com
901273-01D
12
INSPECTING BURNERS
Pilot Assembly
Burner Flame Pattern
CLEANING AND MAINTENANCE
REPLACEMENT PARTS
INSPECTING BURNERS
Check pilot flame pattern and burner flame patterns often.
PILOT ASSEMBLY
The pilot assembly is factory preset for the proper flame height.
Alterations may have occurred during shipping and handling. The
pilot is located on the back right hand side of the burner.
The thermocouple should be fully enveloped in the flame. The flame
should not be lifting off of the thermocouple element.
If your pilot assembly does not meet these requirements:
• Turn the adjustment screw marked pilot clockwise to decrease
or counterclockwise to increase the flame to proper size (see
Figure 20). Do not remove the adjustment screw.
• see Troubleshooting, pages 13 through 15
Thermocouple
Pilot
Figure 19 - Correct Pilot Flame Pattern
CLEANING AND
MAINTENANCE
• Keep the area around the log set clean and clear of debris.
• Occasionally, you may use a soft bristle brush to clean logs.
• Periodically inspect the air mixer and burner tube for foreign
matter blocking the air inlet and flame holes.
• Once every year a qualified agency or certified chimney sweep
should examine and clean the venting system of the fireplace.
REPLACEMENT PARTS
Note: Use only original replacement parts. This will protect your
warranty coverage for parts replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If they can’t supply
original replacement part(s), call DESA International’s Technical
Service Department at 1-866-672-6040. When calling DESA International, have ready
• your name and address
• model and serial numbers of your log set
• how log set was malfunctioning
• type of gas used (propane or natural gas)
• purchase date
T
Usually, we will ask you to return the defective part to the factory.
Pilot
Adjustment
Screw
PARTS NOT UNDER
WARRANTY
Figure 20 - Locating Pilot Adjustment Screw
BURNER FLAME PATTERN
Burner flames will be steady; not lifting or floating. Flames should
go up through the middle of logset. Flames should not "spill" to the
edges of the pan or sides of the logset.
Contact authorized dealers of this product. If they can’t supply original
replacement part(s), call DESA International at 1-866-672-6040.
When calling DESA International, have ready
• model number of your log set
• the replacement part number
Figure 21 shows a typical flame pattern. If burner flame pattern differs
from that described:
• turn appliance off (see To Turn Off Gas to Appliance, page 11)
• see Troubleshooting, pages 13 through 15
Figure 21 - Typical Flame Pattern
For more information, visit www.desatech.com
901273-01D
TROUBLESHOOTING
13
13
TROUBLESHOOTING
WARNING: Turn off log set and let cool before
servicing. Only a qualified service person should
service and repair log set.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Log set is smoking/sooting excessively
(Note: It is natural and unavoidable for
vented gas log sets to produce moderate
levels of carbon (soot) where flames
contact the logs. This is especially true
with propane/LP gas.)
1. Poor fuel quality
1. Contact local natural or propane/LP gas
company
2. Adjust damper wide open and/or have
fireplace and venting professionally
cleaned and checked
3. Separate the logs to allow more flame
passage
4. Remove any foreign items from the
flame pattern and/or check for proper
orifice sizing
5. Preheat flue in very cold weather
2. Fireplace venting system not drafting
properly
3. Excessive flame impingement or
blockage
4. Improper fuel/air mixture
5. Excessive gas supply/pressure
Burner is excessively noisy
(Note: The movement and combustion of
gas will create low, unavoidable levels of
noise.)
1. Passage of air/gas across irregular surfaces
2. Excessive gas pressure on natural gas
units
1. Relieve any tight bends or kinks in gas
supply line
2. Check/reset gas regulator pressure (see
Adjusting Regulator Pressure For Propane/LP Conversion, page 7)
Burner flame is too low or too high
1. Incorrect gas supply or pressure
2. Blocked burner orifice or burner manifold ports
3. Improper burner orifice size
1. Check for proper gas supply pressure
2. Free burner orifice and manifold ports
of any burrs, paint, or other blockage
3. Verify proper burner orifice sizing (see
Figure 2, page 4)
Remote does not function (GHRC only)
1. Battery is not installed. Battery power
is low
1. Replace 9-volt batteries in receiver and
remote control
For more information, visit www.desatech.com
901273-01D
14
TROUBLESHOOTING
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no
spark at pilot
1. Ignitor electrode not connected to ignitor cable
2. Ignitor cable pinched or wet
1. Reconnect ignitor cable
3. Bad ground on piezo ignitor
4.
5.
6.
7.
When ignitor button is pressed, there is
spark at pilot but no ignition
Broken ignitor cable
Bad piezo ignitor
Ignitor electrode broken
Ignitor electrode positioned wrong
1. Gas supply turned off or equipment
shutoff valve closed
2. Control knob not in PILOT position
3. Control knob not pressed in while in
PILOT position
4. Air in gas lines when installed
5. Pilot adjustment screw closed
6. Pilot is clogged
7. Low gas pressure
Pilot lights but flame goes out when control
knob is released
1. Control knob not fully pressed in
2. Control knob not pressed in long enough
3. Equipment shutoff valve not fully open
4. Pilot flame not touching thermocouple,
which allows thermocouple to cool,
causing pilot flame to go out. This problem could be caused by one or both of
the following:
A) Low gas pressure
B) Dirty or partially clogged pilot
5. Thermocouple connection loose at control valve
6. Thermocouple damaged
7. Control valve damaged
Burner does not light after pilot is lit
1. Burner orifice clogged
2. Inlet gas pressure is too low
3. Burner orifice diameter is too small
4. Thermocouple leads disconnected or improperly connected
Delayed ignition burner
1. Pilot flame needs adjusting
2. Wrong pilot orifice
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Scrape away paint on bracket for better
contact with ground on piezo ignitor
4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace electrode
7. Reposition electrode
1. Turn on gas supply or open equipment
shutoff valve
2. Turn control knob to PILOT position
3. Press in control knob while in PILOT
position
4. Continue holding down control knob.
Repeat igniting operation until air is removed
5. Adjust pilot flame for approximately
2" blue flame
6. Clean pilot (see Cleaning and Maintenance, page 12) or replace pilot assembly
7. Replace gas control
1. Press in control knob fully
2. After pilot lights, keep control knob
pressed in 30 seconds
3. Fully open equipment shutoff valve
4. A) Contact local natural gas company
B) Clean pilot (see Cleaning and Maintenance, page 12) or replace pilot assembly
5. Hand tighten until snug, then tighten
1/4 turn more
6. Replace thermocouple
7. Replace control valve
1. Clean burner orifice
2. Contact local natural or propane/LP gas
company
3. Replace burner orifice
4. Reconnect leads
1. Adjust pilot flame for approximately
2" blue flame
2. Replace pilot orifice set
For more information, visit www.desatech.com
901273-01D
TROUBLESHOOTING
15
15
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating log set where impurities in air exist may create odors.
Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new
carpet or textiles, etc., create fumes. These fumes may mix with combustion air
and create odors. These odors will disappear over time.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Log Set produces a clicking/ticking noise
just after burner is lit or shut off
1. Metal expanding while heating or contracting while cooling
1. This is common with most log sets. If
noise is excessive, contact qualified service person
Log Set produces unwanted odors
1. Log Set burning vapors from paint, hair
spray, glues, cleaners, chemicals, new
carpet, etc. (See IMPORTANT statement above)
2. Gas leak. See Warning statement at
top of page
1. Open flue to maximum. Stop using odor
causing products while log set is running
Gas odor even when control knob is in OFF
position
1. Gas leak. See Warning statement at
top of page
2. Control valve defective
1. Locate and correct all leaks (see Checking Gas Connections, page 6)
2. Replace control valve
Gas odor during combustion
1. Gas leak. See Warning statement at
top of page
1. Locate and correct all leaks (see Checking Gas Connections, page 6)
2. Locate and correct all leaks (see Checking Gas Connections, page 6)
For more information, visit www.desatech.com
901273-01D
16
ILLUSTRATED PARTS BREAKDOWN
Models VVSA18R, VVSA24R, VVDA18R, VVDA24R, and VVDA30R
ILLUSTRATED PARTS
BREAKDOWN
MODELS VVSA18R, VVSA24R, VVDA18R,
VVDA24R, AND VVDA30R
9
9
10
7
25
17
12
5
23
22
14
17
11
5
20
6
4
19
24
3
16
13
15
2
N
O
FF
O
18
P
ILOT
21
8
1
For more information, visit www.desatech.com
901273-01D
PARTS LIST
Models VVSA18R, VVSA24R, VVDA18R, VVDA24R, and VVDA30R
17
17
PARTS LIST
This list contains replaceable parts used in your log set. When
ordering parts, follow the instructions listed under Replacement
Parts on page 12 of this manual.
KEY PART NUMBER FOR
NO.
VVSA18R
VVSA24R
VVDA18R
VVDA24R
VVDA30R
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
901063-01
901056-01
901066-01
901064-03
901208-01
901136-01
901242-01
901232-01
901430-01
901243-01
—
—
—
106824-01
901066-02
901065-02
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
901063-01
901056-01
901066-01
901064-04
901208-02
901136-02
901242-01
901232-01
901430-01
901243-02
—
—
—
106824-01
901066-02
901065-03
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
901063-01
901056-01
901066-01
901064-03
901209-01
901137-01
901242-01
901232-01
901431-01
901246-01
901681-01
901078-01
901076-01
106824-01
901066-02
901065-02
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
901063-01
901056-01
901066-01
901064-08
901209-02
901137-02
901242-01
901232-01
901431-01
901246-02
901681-01
901078-01
901076-01
106824-01
901066-02
901065-03
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
901063-01
901056-01
901066-01
901064-09
901209-03
901137-03
901242-01
901232-01
901431-01
901246-03
901681-01
901078-01
901076-01
106824-01
901066-02
901065-04
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
Brass 3/8 FLR x 1/2 FPT Elbow
Brass 3/8 FLR x 3/8 MPT Elbow
Brass Air Mixer - Natural Gas
Natural Gas Injector
Burner Manifold
Burner Pan
Damper Clamp - Std. Assembly
Gas Line - 12" Aluminum
Grate Steps
Log Grate
Burner Strap
Nut #8/32
Screw #8/32 x 3/8
Piezo Cover
Propane/LP Brass Air Mixer
Propane/LP Brass Orifice
Screw 1/4" #8 “B” pt
Jumper Wire
Machine Screw #10-32 x 3.8" (901077-01)
Piezo Igniter
Valve, mV
Pilot Burner (with natural gas orifice)
Piezo Ignitor Electrode
Steel Shroud
Propane/LP Pilot Burner Orifice
QTY.
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
6
1
1
1
1
1
1
1
1
PARTS AVAILABLE — NOT SHOWN
901156-01
901155-01
901156-01
901155-01
901156-01
901155-01
901156-01
901155-01
901156-01
901155-01
901838-01
901838-01
901838-01
901838-01
901838-01
.125# Bag Embers
1.5# Bag Ash Bed Material
(Vermiculite)
Remote Receiver Cover (Log)
For more information, visit www.desatech.com
901273-01D
1
1
1
18
ILLUSTRATED PARTS BREAKDOWN
Models VSLR18, VSLR24, VDLCR18, VDLCR24, and VDLCR30
ILLUSTRATED PARTS
BREAKDOWN
8
HANOVER ROUND OAK LOG MODELS
VSLR18, VSLR24
6
7
KINGSTON SPLIT OAK LOG MODELS
VDLCR18, VDLCR24, AND VDLCR30
5
4
9
1
3
15
2
12
Kingston Split Oak Logs
13
14
10
11
Hanover Round Oak Logs
For more information, visit www.desatech.com
901273-01D
PARTS LIST
Models VSLR18, VSLR24, VDLCR18, VDLCR24, and VDLCR30
19
19
PARTS LIST
This list contains replaceable parts used in your log set. When
ordering parts, follow the instructions listed under Replacement
Parts on page 12 of this manual.
KEY PART NUMBER FOR
NO.
VSLR18
VSLR24
VDLCR18
VDLCR24
VDLCR30
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
—
—
—
—
—
—
—
—
—
901625-03
901583-01
901541-02
901580-01
901579-01
—
—
—
—
—
—
—
—
—
—
901626-03
901584-01
901541-02
901580-01
901579-01
901578-01
901565-02
901603-01
901593-01
—
901588-01
—
901591-02
901551-03
901587-01
—
—
—
—
—
—
901566-02
901604-01
901594-01
—
901588-01
901592-01
901591-02
901551-03
901587-01
—
—
—
—
—
—
901567-02
901604-04
901595-01
901580-02
901588-01
901592-01
901591-02
901551-03
901587-01
—
—
—
—
—
—
Bottom Rear
Bottom Front
Bottom Front
VR-11\VC Top Log
VS-12 Top Log
VCR-12 Top Log
VCR-11\VC Top Log
CHR-13\VC Top Log
VCR-9 Top Log
Bottom Rear
Bottom Front
CPR-13\VR Top Log
VR-11\VR Top Log
VR-10Y Top Log
VR-10 Top Log
For more information, visit www.desatech.com
901273-01D
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
20
ILLUSTRATED PARTS BREAKDOWN
Models FVSA18R, FVSA24R, FVDA18R, FVDA24R, and FVDA30R
ILLUSTRATED PARTS BREAKDOWN
MODELS FVSA18R, FVSA24R, FVDA18R,
FVDA24R, AND FVDA30R
9
9
10
7
25
17
12
5
23
22
14
17
11
5
20
6
4
19
24
3
16
13
15
2
N
O
FF
O
18
P
ILOT
21
8
1
For more information, visit www.desatech.com
901273-01D
PARTS LIST
Models FVSA18R, FVSA24R, FVDA18R, FVDA24R, and FVDA30R
21
21
PARTS LIST
This list contains replaceable parts used in your log set. When
ordering parts, follow the instructions listed under Replacement
Parts on page 12 of this manual.
KEY PART NUMBER FOR
NO.
FVSA18R
FVSA24R
FVDA18R
FVDA24R
FVDA30R
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
901063-01
901056-01
901066-01
901064-03
901208-01
901136-01
901242-01
901232-01
901430-01
901243-01
—
—
—
106824-01
901066-02
901065-02
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
901063-01
901056-01
901066-01
901064-04
901208-02
901136-02
901242-01
901232-01
901430-01
901243-02
—
—
—
106824-01
901066-02
901065-03
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
901063-01
901056-01
901066-01
901064-03
901209-01
901137-01
901242-01
901232-01
901431-01
901246-01
901681-01
901078-01
901076-01
106824-01
901066-02
901065-02
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
901063-01
901056-01
901066-01
901064-08
901209-02
901137-02
901242-01
901232-01
901431-01
901246-02
901681-01
901078-01
901076-01
106824-01
901066-02
901065-03
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
901063-01
901056-01
901066-01
901064-09
901209-03
901137-03
901242-01
901232-01
901431-01
901246-03
901681-01
901078-01
901076-01
106824-01
901066-02
901065-04
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901070-01
Brass 3/8 FLR x 1/2 FPT Elbow
Brass 3/8 FLR x 3/8 MPT Elbow
Brass Air Mixer - Natural Gas
Natural Gas Injector
Burner Manifold
Burner Pan
Damper Clamp - Std. Assembly
Gas Line - 12" Aluminum
Grate Steps
Log Grate
Burner Strap
Nut #8/32
Screw #8/32 x 3/8
Piezo Cover
Propane/LP Brass Air Mixer
Propane/LP Brass Orifice
Screw 1/4" #8 “B” pt
Jumper Wire
Machine Screw #10-32 x 3.8" (901077-01)
Piezo Igniter
Valve, mV
Pilot Burner (with natural gas orifice)
Piezo Ignitor Electrode
Steel Shroud
Propane/LP Pilot Burner Orifice
QTY.
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
6
1
1
1
1
1
1
1
1
PARTS AVAILABLE — NOT SHOWN
901156-01
901155-01
901156-01
901155-01
901156-01
901155-01
901156-01
901155-01
901156-01
901155-01
901838-01
901838-01
901838-01
901838-01
901838-01
.125# Bag Embers
1.5# Bag Ash Bed Material
(Vermiculite)
Remote Receiver Cover (Log)
For more information, visit www.desatech.com
901273-01D
1
1
1
ILLUSTRATED PARTS BREAKDOWN
22
Models FSLR18, FSLR24, FDLCR18, FDLCR24, and FDLCR30
ILLUSTRATED PARTS
BREAKDOWN
8
ARLINGTON ROUND OAK LOG MODELS
FSLR18, FSLR24
7
MANCHESTER SPLIT OAK LOG MODELS
FDLCR18, FDLCR24, AND FDLCR30
6
4
5
1
3
9
15
2
Manchester Split Oak Logs
12
14
10
13
11
Arlington Round Oak Logs
For more information, visit www.desatech.com
901273-01D
PARTS LIST
Models FSLR18, FSLR24, FDLCR18, FDLCR24, and FDLCR30
23
23
PARTS LIST
This list contains replaceable parts used in your log set. When
ordering parts, follow the instructions listed under Replacement
Parts on page 12 of this manual.
KEY
PART NUMBER FOR
NO.
FSLR18
FSLR24
FDLCR18
FDLCR24
FDLCR30
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
—
—
—
—
—
—
—
—
—
901625-01
901635-01
901620-01
901622-01
—
901623-01
—
—
—
—
—
—
—
—
—
901626-01
901636-01
901620-01
901622-01
901547-01
901623-01
901565-03
901656-01
901666-01
901619-01
901617-01
901612-01
901620-02
—
—
—
—
—
—
—
—
901566-03
901657-01
901667-01
901619-01
901617-01
901612-01
901620-02
901614-01
—
—
—
—
—
—
—
901567-03
901658-01
901668-01
901619-01
901617-01
901612-01
901620-02
901614-01
901623-02
—
—
—
—
—
—
Bottom Rear Log
Bottom Front Log
Bottom Front Log
FS-12Y Top Log
FS-16 Top Log
FS-17 Top Log
FR12L Top Log
FS15 Top Log
FR14 Top Log
Bottom Rear Log
Bottom Front Log
FR12L Top Log
FR11 Top Log
CPR11 Top Log
FR14 Top Log
For more information, visit www.desatech.com
901273-01D
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
24
ILLUSTRATED PARTS BREAKDOWN
Models CVDA18R, CVDA24R, and CVDA30R
ILLUSTRATED PARTS
BREAKDOWN
31
30
MODELS CVDA18R, CVDA24R,
AND CVDA30R
28
29
26
32
27
25
25
9
9
10
7
33
17
23
12
22
14
17
11
5
20
6
4
19
24
3
16
13
15
2
O
N
FF
O
18
P
ILOT
21
8
1
For more information, visit www.desatech.com
901273-01D
PARTS LIST
Models CVDA18R, CVDA24R, and CVDA30R
PARTS LIST
This list contains replaceable parts used in your log set. When
ordering parts, follow the instructions listed under Replacement
Parts on page 12 of this manual.
KEY
PART NUMBER FOR
NO.
CVDA18R
CVDA24R
CVDA30R
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
901058-01
901056-01
901066-01
901064-03
901209-01
901137-01
901242-01
101628-01
901431-01
901246-01
901681-01
901078-01
901076-01
106824-01
901066-02
901065-02
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901645-01
901528-01
901591-03
901587-03
—
901527-03
901541-03
—
901070-01
901058-01
901056-01
901066-01
901064-08
901209-02
901137-02
901242-01
101628-01
901431-01
901246-02
901681-01
901078-01
901076-01
106824-01
901066-02
901065-03
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901646-01
901566-01
901591-03
901587-03
901551-02
901527-03
901541-03
—
901070-01
901058-01
901056-01
901066-01
901064-09
901209-03
901137-03
901242-01
101628-01
901431-01
901246-03
901681-01
901078-01
901076-01
106824-01
901066-02
901065-04
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901647-01
901567-01
901591-03
901587-03
901551-02
901527-03
901541-03
901528-01
901070-01
Brass 3/8 FLR x 1/2 FPT
Brass 3/8 FLR x 3/8 MPT Elbow
Brass Air Mixer - Natural Gas
Natural Gas Injector
Burner Manifold
Burner Pan
Damper Clamp - Std. Assembly
Gas Line - 10" Flexible
Grate Steps
Log Grate
Burner Strap
Nut #8/32
Screw #8/32 x 3/8
Piezo Cover
Propane/LP Brass Air Mixer
Propane/LP Brass Orifice
Screw 1/4" #8 “B” pt
Jumper Wire
Machine Screw #10-32 x 3/8 (901077-01)
Piezo Igniter
Valve, mV
Pilot Burner (with natural gas orifice)
Piezo Igniter Electrode
Steel Shroud
Bottom Front Log
Bottom Rear Log
VCR11/CC Top Log
VCR9/CC Top Log
CHR13/CC Top Log
CS12/CC Top Log
CPR13/CC Top Log
CS16/CC Top Log
Propane/LP Pilot Burner Orifice
901156-01
901155-01
901156-01
901155-01
901156-01
901155-01
901838-01
901838-01
901838-01
QTY.
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
6
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
PARTS AVAILABLE — NOT SHOWN
.125# Bag Embers
1.5# Bag Ash Bed Material
(Vermiculite)
Remote Receiver Cover (Log)
For more information, visit www.desatech.com
901273-01D
1
1
1
25
25
26
ILLUSTRATED PARTS BREAKDOWN
Models CPVSA18R, and CPVSA24R
ILLUSTRATED PARTS
BREAKDOWN
28
27
26
MODELS CPVSA18R, AND CPVSA24R
25
9
23
9
10
24
22
29
14
7
5
20
19
11
14
17
6
16
4
21
3
13
12
2
N
O
FF
O
15
P
ILOT
18
8
1
For more information, visit www.desatech.com
901273-01D
PARTS LIST
Models CPVSA18R, and CPVSA24R
PARTS LIST
This list contains replaceable parts used in your log set. When
ordering parts, follow the instructions listed under Replacement
Parts on page 12 of this manual.
KEY
PART NUMBER FOR
NO.
CPVSA18R
CPVSA24R
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
901058-01
901056-01
901066-01
901064-03
901209-01
901136-01
901242-01
101628-01
901431-01
901246-01
106824-01
901066-02
901065-02
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901641-01
901625-02
—
901555-01
901550-01
901551-01
901556-01
901070-01
901058-01
901056-01
901066-01
901064-04
901209-02
901136-02
901242-01
101628-01
901431-01
901246-02
106824-01
901066-02
901065-03
901075-01
105575-01
M12461-26
097159-04
901071-01
901073-01
901072-01
106823-01
901642-01
901626-02
901580-04
901555-01
901550-01
901551-01
901556-01
901070-01
Brass 3/8 FLR x 1/2 FPT
Brass 3/8 FLR x 3/8 MPT Elbow
Brass Air Mixer - Natural Gas
Natural Gas Injector
Burner Manifold
Burner Pan
Damper Clamp - Std. Assembly
Gas Line - 10" Flexible
Grate Steps
Log Grate
Piezo Cover
Propane/LP Brass Air Mixer
Propane/LP Brass Orifice
Screw 1/4" #8 “B” pt
Jumper Wire
Machine Screw #10/32 x 3/8 (901077-01)
Piezo Igniter
Valve, mV
Pilot Burner (with natural gas orifice)
Piezo Igniter Electrode
Steel Shroud
Bottom Front Log
Bottom Rear Log
VR11/CH Top Log
CHR10/CH Top Log
CHR11/CH Top Log
CHR13/CH Top Log
CHR13Y/CH Top Log
Propane/LP Pilot Burner Orifice
QTY.
1
1
1
1
1
1
1
1
2
1
1
1
1
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
PARTS AVAILABLE — NOT SHOWN
901156-01
901155-01
901156-01
901155-01
901838-01
901838-01
.125# Bag Embers
1.5# Bag Ash Bed Material
(Vermiculite)
Remote Receiver Cover (Log)
For more information, visit www.desatech.com
901273-01D
1
1
1
27
27
28
ACCESSORIES
ACCESSORIES
Purchase these heater accessories from your local dealer. If they can not
supply these accessories, call DESA International at 1-866-672-6040
for referral information. You can also write to the address listed on the
back page of this manual.
SILICA SAND - GA9850A
(Not Shown)
For all models. Use for firebox decoration only. Carton of 6.
LAVA ROCK - GA6067A
(Not Shown)
For all models. Use for firebox decoration only.
DECORATIVE ASH BED CONTROL COVER
CDABKA (Not Shown)
An attractive way to cover control knob and piezo ignitor.
RECEIVER AND HAND-HELD REMOTE
CONTROL KIT - GHRC SERIES
18" ORNAMENTAL GRATE ENHANCER
GA9350A (Not Shown)
For 18" models only. Additional decoration for front grate.
For all models. Allows the gas log heater to be turned on and off by
using a hand-held remote control.
24" ORNAMENTAL GRATE ENHANCER
GA9360A (Not Shown)
WALL-MOUNT ON/OFF SWITCH - GWMS2
For 24" models only. Additional decoration for front grate.
(Not Shown)
For all models. Allows the gas log heater to be turned on and off
with a wall switch.
ASH BED MATERIAL (Vermiculite) - GA9750A
30" ORNAMENTAL GRATE ENHANCER
GA9370A (Not Shown)
For 30" models only. Additional decoration for front grate.
(Not Shown)
For all models. Carton of 6.
GLOWING EMBERS - GA9950A
(Not Shown)
For all models. Use for firebox decoration only.
For more information, visit www.desatech.com
901273-01D
29
29
OWNER'S REGISTRATION FORM
In order to provide better customer service for this and future purchases, we recommend that you register your product with us.
You can register online at www.desatech.com. If access to our website is not available to you, please complete this Owner’s
Registration Form and mail to the address on the back of this owner’s manual. Please provide the following product information:
Brand:
(Comfort Glow, Vanguard, etc.)
Model:
(EFP33PR, VTGH33NR, etc.)
Date Purchased:
Note: Keep receipt for warranty verification.
Serial Number:
7 or 9 digit number located on product or identification tag.
First Name:
Last Name:
Address:
City:
Home Phone:
State:
(
)
Zip:
Country:
-
E-Mail:
Please answer the following questions to register your product with DESA International:
1.
Where will the product be used?
2.
If you bought this product yourself, did you plan to purchase this type of product before going into the store?
3.
Who selected the product? ❍ Male ❍ Female ❍ Both
❍ Living/Family Room
4.
❍ Office/Warehouse
❍ Utility Shed/Outbuilding
What is the population of your area? ❍ Under 10,000
❍ 100,000 to 250,000
❍ 10,000 to 25,000
❍ Bedroom
❍ 25,000 to 50,000
❍ Bathroom
❍ Propane (LP Gas)
❍ Fuel Oil
5.
What is your primary source of heat?
How was the product installed? ❍ Professional Installer
7.
Cost of product excluding sales tax? $___________________
8.
Cost to install product? $____________________
9.
Type of store where product was purchased? ❍ Hardware
❍ Fireplace or Hearth Shop
❍ Farm Store
❍ Self
❍ 50,000 to 100,000
❍ Emergency Back-Up Heat
❍ Heater was on Sale
12. Level of Education of Purchaser: ❍ Some High School
❍ 20 - 29
❍ Natural Gas
❍ Propane Dealer
❍ Electric
❍ Natural Gas/Utility Co.
❍ 30 - 39
❍ Relative or Friend
❍ Other
❍ Home Center/Builder’s Supply
❍ 40 - 49
❍ 50 - 59
❍ D.I.Y. Home Project
❍ Construction Project
❍ Store Display
❍ Completed High School
14. Buyer’s total annual household income: ❍ Under $15,000
❍ $75,000 to $99,999
❍ Replace Older Model
❍ Energy Savings/High Efficiency
11. How did you learn about this product brand? ❍ Advertising
13. Age of Purchaser: ❍ Under 20
❍ Wood
❍ Other
❍ Other
10. What motivated you to buy this product? ❍ Sudden Cold Weather
❍ Completed College
❍ $15,000 to $19,999
❍ $20,000 to $34,999
Name: ______________________________________
City: _______________________ State: __________
16. In choosing this product, how important were the following:
Not Important
Somewhat Important
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
visit
❍
❍ Completed Graduate School
❍ 60 or Over
❍ $100,000 and Over
Availability
❍
Price
❍
Brand Name
❍
Overall Quality
❍
Heat Output
❍
Made in USA
❍
Warranty
❍
Local Service
❍
Value for Price
❍
Prior Brand Experience
❍
Controls Location
❍
Thermostat, Remote, or Manual Operation
❍
Ease of Operation
❍
Special Features
❍
Salesperson’s Recommendation
❍
Friend/Relative’s Recommendation
❍
Portability
❍
For more information,
Quiet Operation
❍
❍ Other
❍ Other ________________________
15. Store where product was purchased:
901273-01D
❍ Other
❍ Yes ❍ No
❍ Over 250,000
6.
❍ $50,000 to $74,999
❍ Garage
Very Important
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
www.desatech.com
❍
❍ $35,000 to $49,999
TAPE
30
Postage
Required
TM
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
For more information, visit www.desatech.com
TAPE
901273-01D
NOTES
31
31
NOTES
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
For more information, visit www.desatech.com
901273-01D
32
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We make
no other warranty, expressed or implied.
LIMITED WARRANTY
VENTED GAS LOGS
DESA International warrants this product to be free from defects on burner system for four (4) years, valves/controls for one (1) year, and logs for
a lifetime from the date of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all
applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this log set to proper operating
condition and an allowance for labor when provided by a DESA International's Authorized Service Center. Warranty part(s) MUST be obtained
through authorized dealers of this product and/or DESA International who will provide original factory replacement parts. Failure to use original
factory replacement parts voids this warranty. The log set MUST be installed by a qualified installer in accordance with all local codes and instructions
furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a
result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and
any and all such other costs related to repairing a defective log set will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS
EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
TO FOUR (4) YEARS ON BURNER SYSTEM, VALVES/CONTROLS FOR ONE (1) YEAR, AND A LIFETIME ON LOGS FROM THE DATE
OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE
PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so
the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
TM
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
901273 01
NOT A UPC
901273-01
Rev. D
10/02
For more information, visit www.desatech.com
901273-01D