Sid Harvey part #'s DVO-12-12 and M4-83A ...

Sid Harvey part #'s DVO-12-12 and M4-83A    ...
Sid Harvey part #'s DVO-12-12 and M4-83A
SDS # Z0493
Sid Harvey part # DVO-12-12
MSDS # Z0493
MATERIAL SAFETY DATA SHEET
1. PRODUCT AND COMPANY IDENTIFICATION
Brand Name:
Manufacturer:
Pinnacle Oil, Inc.
City:
Indianapolis
Product Name(s):
Address:
5009 W. 81st Street
Zip:
46268
Vacuum Pump Oil
State:
IN
Fax:
(317) 875-0889
Phone:
(800) 829-8899
Black Gold
Emergency Number:
2. COMPOSITION/INFORMATION ON INGREDIENTS
Component Name:
CAS#:
% Volume:
ACGIH TLV
(800) 829-8899
ACGIH STEL
OSHA PEL
Oil Mist, If Generated
None
N/A
5 mg/m3, 8 hr.
TWA
10 mg/m3, 8 hr.
TWA
5 mg/m3, 8 hr.
TWA
Lubricant Base Oil(Petroleum)
Mixture
100
See Oil Mist, if
Generated
See Oil Mist, if
Generated
See Oil Mist, if
Generated
The base oil for this product can be a mixture of any of the following highly refined petroleum streams:
64741-88-4,64742-01-4,64742-54-7,64742-65-0,64742-47-8,8042-47-5,64742-46-7,64742-52-5,64742-54-7,72623-84-8,72623-85-9,72623-860,72623-87-1,178603-63-9,178603-64-0,178603-65-1,178603-66-2, 68037-01-4, 151006-63-2
Note:
State, local, or other agencies or advisory groups may have established more stringent limits. Consult an industrial
hygienist or similar professional, or your local agencies, for further information. All components are listed on the TSCA
inventory.
3. HAZARDS IDENTIFICATION
P otential Health E ffec ts
Emergency
Overview:
Oily Liquid with Hydrocarbon Odor. Can cause eye irritation. Can burn in fire, releasing toxic vapors, gases
and fumes. Extremely slippery when spilled.
Eye:
Contact may cause mild eye irritation including stinging, watering, and redness.
Skin:
Contact may cause mild skin irritation including redness, and a burning sensation. Prolonged or repeated contact can
worsen irritation by causing drying and cracking of the skin leading to dermatitis(inflammation). No harmful effects
from skin absorption are expected.
Ingestion:
No harmful effects expected from ingestion.
Inhalation:
No information available. Studies by other exposure routes suggest a low degree of toxicity by inhalation.
Chronic Effects:
Effects of overexposure may include irritation of the nose and throat, irritation of the digestive tract, nausea and
diarrhea.
Potential
Environmental
Effects:
See Ecological Information, See Section 12.
4. FIRST AID MEASURES
Eye:
If irritation or redness develops, move victim away from exposure and into fresh air. Flush eyes with clean water. If
symptoms persist, seek medical attention.
Skin:
Wipe material from skin and remove contaminated shoes and clothing. Cleanse affected area(s) thoroughly by
washing with mild soap and water and, if necessary, a waterless skin cleanser. If irritation or redness develops and
persists, seek medical attention.
Inhalation:
If respiratory symptoms develop, move victim away from source of exposure and into fresh air. If symptoms persist,
seek medical attention. If victim is not breathing, clear airway and immediately begin artifical respiration. If breathing
difficulties develop, oxygen should be administered by qualified personnel. Seek immediate medical attention.
Ingestion:
First aid is not normally required; however, if swallowed and symptoms develop, seek medical attention.
Note to
Physicans:
High pressure hydrocarbon injection injuries may produce a substantial necrosis of underlying tissue despite an
innocuous appearing external wound. Often these injuries require extensive emergency surgical debridement and all
injuries should be evaluated by a specialist in order to assess the extent of the injury. Acute aspirations of large
amounts of oil-laden material may product a serious aspiration pneumonia. Patients who aspirate these oils should be
Date Revised :
October 1, 2009
Page 1 of 4
followed for the development of long-term sequelae. Inhalation exposure to oil mists below current workplace
exposure limits is unlikely o cause pulmonary abnormalities.
5. FIRE FIGHTING MEASURES
Flash Point:
LEL/UEL % No Data
390F-D92
Auto Igniton Temperature:
No Data
OSHA Flammability Class:
Not applicable
Extinguishing Media:
Dry chemical, carbon dioxide, foam, or water spray is recommended. Water or foam may cause frothing of
materials heated above 212F. Carbon dioxide can displace oxygen. Use caution when applying carbon dioxide in
confined spaces.
Fire Fighting Instructions:
For fires beyond the incipient stage, emergency responders in the immediate hazard area should wear bunker
gear. When the potential chemical hazard in unknow, in enclosed or confined spaces, or when explicitly required
by DOT, a self contained breathing apparatus should be worn. In addition, wear other appropriate protective
equipment as conditions warrant(see Section 8). Isolate immediate hazard area, keep unauthorized personnel out.
Stop spill release if it can be done with minimal risk. Move undamaged containers from immediate hazard area if it
can done with minimal risk. Water spray may be useful in minimizing or dispersing vapors and to protect
personnel. Cool equipment exposed to fire with water, if it can be done with minimal risk. Avoid spreading burning
liquid with water used for cooling purposes.
Fire and Explosion Hazards:
This material may burn, but will not ignite readily. Vapors are heavier than air and can accumulate in low areas. If
container is not properly cooled, it can rupture in the heat of a fire.
6. ACCIDENTIAL RELEASE MEASURES
Accidental Release
Measures:
This material may burn, but will not ignite readily. Keep all sources of ignition away from spill/release. Stay
upwind and away from spill/release. Notify persons down wind of the spill/release, isolate immediate hazard area
and keep unauthorized personnel out. Stop spill/release if it can be done with minimal rish. Wear appropriate
protective equipment including respiratory protection as conditions warrant(see Section 8).
Prevent spilled material from entering sewers, storm drains, other unauthorized drainage systems, and natural
waterways. Dike far ahead of spill for later recovery or disposal. Spilled material may be absorbed into an
appropriate absorbent material.
Notify fire authorities and appropriate federal, state and local agencies. Immediate cleanup of any spill is
recommended. If spill of any amount is made into or upon navigable waters, the contiguous zone, or adjoining
shorelines, notify the National Response Center(phone number 800-424-8802).
7. HANDLING AND STORAGE
Handling:
Do not enter confined spaces such as tanks or pits without following proper entry procedures such as ASTM D-4276
and 29CFR 1910.146. The use of appropriate respiratory protection is advised when concentrations exceed any
established exposure limits(See Section 2 and 8).
Do not wear contaminated clothing or shoes. Use good personal hygiene practices.
High pressure injection of hydrocarbon fuels, hydraulic oils or greases under the skin may have serious consequences
even though no symtoms or injury may be apparent. This can happen accidentally when using high pressure
equipment such as high pressure grease guns, fuel injectiton appartus or from pinhole leaks in tubing of high pressure
hydraulic oil equipment.
Empty containers retain residue and may be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or
expose such containers to heat, flame, sparks, or other sources of ignition. They may explode and cause injury or
death. Empty drums should be completely drained, properly bunged, and promptly shipped to the supplier or drum
reconditioner. All containers should be disposed of in an environmentally safe manner and in accordance with
governmental regulations.
Before working on or in tanks which contain or have contained this material, refer to OSHA regulations, ANSI Z49.1
and other references pertaining to cleaning, repairing, welding, or other contemplated operations.
Storage:
Keep container(s) tightly closed. Use and store this material in cool, dry, well-ventilated areas away from heat and all
sources of ignition. Storage temperatures above 113F may lead to thermal decomposition, resulting in the generation
of hydrogen sulfide and other sulfur containing gases. Store only in approved containers. Keep away from any
incompatible material(see Section 10). Protect container(s) against physical damage.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls:
If current ventilation practices are not adequate to maintain airborne concentrations below the
established exposure limits(see Section 2), additional ventilation of exhaust system may be
required.
Other Protective Equipment:
A source of clean water should be available in the work area for flushing eyes and skin. Impervious
clothing should be worn as needed.
Eye/Face:
Approved eye protection to safeguard against potential eye contact, irritation, or injury is
recommended. Depending on conditions of use, a face shield may be necessary.
Skin:
The use of gloves impervious is the specific material handled is advised to prevent skin contact and
Date Revised :
October 1, 2009
Page 2 of 4
possible irritation(see manufacturers literature for information on permeability).
Respiratory:
A NIOSH certified air purifying respirator with a Type 95(R or P) particulate filter may be used under
conditions where airborne concentrations are expected to exceed exposure limits(see Section 2).
General Hygiene Considerations:
There are no known hazards associated with this material when used as recommended. The
following general hygiene considerations are recognized as common good industrial hygiene
practices: Avoid breathing vapor or mist, Avoid contact with eyes and skin, Wash thoroughly after
handling and before eating or drinking.
Exposure Guidelines:
See Section 2, Composition/Information on Ingredients.
9. PHYSICAL AND CHEMICAL PROPERTIES
NOTE: Unless otherwise stated, values are determined at 20C(68F) and 760mm Hg(1 atm)
Appearance:
Brown
Solubility in Water:
Not soluble
Odor
Characterisc Petroleum
Flash Point:
390F-D92
Physical State:
Liquid
Flammable/Explosive Limits(%):
pH:
Not applicable
Vapor Pressure(mm Hg):
Not determined
NFPA Health:
Vapor Density(air=1):
Not determined
Boiling Point/Range:
Not determined
Freezing/Melting Point:
Not applicable
Not determined
1
HMIS Health:
1
NFPA Flammability:
1
HMIS Fire:
1
NFPA Reactivity:
0
HMIS Reactivity:
0
10. STABILITY AND REACTIVITY
Stability:
Stable under normal ambient and anticipated storage and handling conditions of temperature and pressure.
Conditions to
Avoid:
Extended exposure to high temperatures can cause decomposition.
Avoid contact with strong oxidizing agents.
Materials to
Avoid(Incompatibl
e Materials):
Hazardous
Decomposition
Products:
Combustion can yield aldehydes and carbon, nitrogen, sulfur, phosphorus and zinc oxides. Hydrogen sulfide and alkyl
mercaptans may also be released. Thermal decomposition may produce hydrogen sulfide and other sulfur-containing
gases at temperatures greater than 113F.
Hazardous
Polymerization:
Will not occur
11. TOXICOLOGICAL INFORMATION
Carcinogenicity:
The petroleum base oils contained in this product have been highly refined by a variety of processes including solvent
extraction, hydrotreating, and dewaxing to remove aromatics and improve performance characteriscs. None of the oils
used are listed as a carcinogen by NTP, IARC, or OSHA.
12. ECOLOGICAL INFORMATION
Ecological
Information:
Not Evaluated at this Time
13. DISPOSAL CONSIDERATIONS
Disposal
Consideration:
This material under most intended uses would become used oil due to contamination by physical or chemical
impurities. RECYCLE ALL USED OIL. While being recycle, used oil is regulated by 40 CFR 279. Use resulting in
chemical or physical change or contamination may also subject it to regulation as hazardous waste. Under federal
regulations, used oil is a solid waste managed under 40 CFR 279. However, in California, used oil is managed as
hazardous waste until tested to show it is not hazardous. Consult state and local regulations regarding the proper
handling of used oil. In the case of used oil, the intent to discard it may cause the used oil to be regulated as
hazardous waste.
14. TRANSPORT INFORMATION
Note:
Date Revised:
Not classified as hazardous
October 1, 2009
Page 3 of 4
15. REGULATORY INFORMATION
OSHA Hazard
Determination:
This material is not known to be hazardous as defined by OSHA's Hazard Communication Standard, 29 CFR
1910.1200.
TSCA
Inventory:
All of the components of this material are listed on theToxic Chemical Substances Inventory. This product is in
compliance with the Toxic Substances Control Act(TSCA).
CERCLA(RQ) :
This product is not subject to CERCLA reporting requirements.
SARA 311/312
Acute Health:
No
Pressure Hazard: No
Chronic Health:
No
Reactive Hazard: No
Fire Hazard:
No
SARA 302/304:
There are no components in this product on the SARA 302/304 list.
SARA 313, Toxic
Component(s):
This product does not contain >1.0%(greater than 0.1% for carginogenic substance) of any chemical substances listed
under SARA Section 313.
California Prop
65:
Warning: This material contains the following chemicals which are known to the State of California to cause cancer,
birth defects or other reproductive harm, and are subject to the requirements of California Proposition 65 (CA Health &
Safety Code Section 25249.5): -- None Known -Used engine oils, while not a component of this material, is on the Proposition 65 list of chemicals known to the State
of California to cause cancer.
16. OTHER INFORMATION
Disclamation:
This information relates only to the specific material designated and may not be valid for such material used for in
combination with other materials or in any process. Such information is, to the best of Pinnacle Oil's knowledge and
belief, accurate and reliable as of the date indicated. However, no representation, warranty or guarantee is made as to
its accuracy, reliability or completeness. It is the user's responsibility to satisfy himself as to the suitableness and
completeness of such information for his particular use.
Preparers Info:
Pinnacle Oil, Inc.
Date Revised :
October 1, 2009
Date Revised:
10/1/2009
Date Prepared:
Page 4 of 4
2 /20/2004
Sid Harvey part # M4-83A MSDS # Z0346
J/B Industries Inc.
Section 1: Product And
Company Identification
COMPANY:
LOCATION:
J/B INDUSTRIES INC.
601 N. Farnsworth Ave.
Aurora, IL 60507
Emergency Telephone Number:
630/851-9444
PRODUCT NAME:
Vacuum Pump Oil
PRODUCT GRADES:
PRODUCT CODE:
DATE ISSUED:
December 28, 1992
DATE REVISED:
September 18, 2006
Sept. 18, 2003
Section 2: Composition/
Information On Ingredients
CAS NAME:
Distillates, hydrotreated heavy paraffinic
CAS NUMBER:
64742-54-7
AMOUNT:
100% weight
This product is not approved for direct
food use [CFR 178.3620 (a) & (b)]
Section 3: Hazards Identification
EMERGENCY OVERVIEW
Clear colorless to pale yellow liquid.
IMMEDIATE HEALTH EFFECTS
EYE:
Not expected to cause prolonged or
significant eye irritation.
SKIN:
Contact with the skin is not expected to
cause prolonged or significant irritation.
Not expected to be harmful to internal
organs if absorbed through the skin.
Contact with the skin is not expected to
cause an allergic skin response.
INGESTION:
Not expected to be harmful if swallowed.
INHALATION:
Not expected to be harmful if inhaled.
Contains a petroleum-based mineral oil.
May cause respiratory irritation or other
pulmonary effects following prolonged
or repeated inhalation of oil mist at
airborne levels above the recomm
ended mineral oil mist exposure limit.
Symptoms of respiratory irritation
may include coughing and
difficulty breathing.
Material Safety Data Sheet
Section 4: First Aid Measures
EYE:
No specific first aid measures are
required because this material is not
expected to cause eye irritation. As a
precaution, remove contact lenses, if
worn, and flush eyes with water.
SKIN:
No specific first aid measures are
required because this material is not
expected to be harmful if it contacts the
skin. As a precaution, remove clothing
and shoes if contaminated. To remove
the material from skin, use soap and
water. Discard contaminated
clothing and shoes or thoroughly
clean before reuse.
No specific first aid measures are
required because this material is not
expected to be harmful if swallowed. Do
not induce vomiting. As a precaution,
give the person a glass of water or milk
to drink and get medical advice. Never
give anything by mouth to an
unconscious person.
INHALATION:
No specific first aid measures are
required because this material is not
expected to be harmful if inhaled. If
exposed to excessive levels of material
in the air, move the exposed person to
fresh air. Get medical attention
if coughing or respiratory
discomfort occurs.
Section 5: Fire Fighting Measures
FIRE CLASSIFICATION;
OSHA Classification (29 CFR
1910.1200): Not classified by OSHA as
flammable or combustible.
NFPA RATINGS:
HEALTH FLAMMABILITY
REACTIVITY
1
0
FLAMMABLE PROPERTIES:
FLASH POINT:
Cleveland Open Cup 378°F (190°C)
(Min)
AUTOIGNITION:
No data available
FLAMMABLE (EXPLOSIVE) LIMITS (% by
volume in air):
Lower N/A
Combustion Products:
Highly dependent on combustion
conditions. A complex mixture of
airborne solids, liquids, and gases
including carbon monoxide, carbon
dioxide, and unidentified organic
compounds will be evolved when this
material undergoes combustion.
Section 6. Accidental Release
Measures
PROTECTIVE MEASURES:
Eliminate all sources of ignition in
vicinity of spilled material.
SPILL MANAGEMENT:
INGESTION:
0
material, do not enter any enclosed or
confined fire space without proper
protective equipment, including selfcontained breathing apparatus.
Upper N/A
EXTINGUISHING MEDIA:
Use water fog, foam, dry chemical or
carbon dioxide (CO2) to extinguish
flames.
PROTECTION OF FIRE FIGHTERS:
Fire Fighting Instructions:
This material will burn although it is not
easily ignited. For fires involving this
Stop the source of the release if you can
do it without risk. Contain release to
prevent further contamination of soil,
surface water or groundwater. Clean up
spill as soon as possible, observing
precautions in Exposure Controls/
Personal Protection. Use appropriate
techniques such as applying noncombustible absorbent materials or
pumping. Where feasible and
appropriate, remove contaminated soil.
Place contaminated materials in
disposable containers and dispose of
in a manner consistent with
applicable regulations.
REPORTING:
Report spills to local authorities and/or
the U.S. Coast Guard's National
Response Center at (800) 424-8802 as
appropriate or required.
Section 7. Handling and Storage
GENERAL HANDLING INFORMATION:
Avoid contaminating soil or releasing this
material into sewage and drainage
systems and bodies of water.
STATIC HAZARD:
Electrostatic charge may accumulate and
create a hazardous condition when
handling this material. To minimize this
hazard, bonding and grounding may be
necessary but may not, by themselves,
be sufficient. Review all operations which
have the potential of generating an
accumulation of electrostatic charge and/
or a flammable atmosphere (including
tank and container filling, splash filling,
tank cleaning, sampling, gauging, switch
loading, filtering, mixing, agitation, and
vacuum truck operations) and use
appropriate mitigating procedures. For
more information, refer to OSHA
1
Standard 29 CFR 1910.106, 'Flammable
and Combustible Liquids', National Fire
Protection Association (NFPA 77,
'Recommended Practice on Static
Electricity; and /or the American
Petroleum Institute (API) Recommended
Practice 2003, 'Protection Against
Ignitions Arising Out of Static, Lightning
and Stray Currents'.
CONTAINER WARNING:
Container is not designed to contain
pressure. Do not use pressure to empty
container or it may rupture with
explosive force. Empty containers retain
product residue (solid, liquid, and/or
vapor) and can be dangerous. Do not
pressurize, cut, weld, braze, solder, drill,
grind, or expose such containers to heat,
flame, sparks, static electricity, or other
sources of ignition. They may explode
and cause injury or death. Empty
containers should be completely
drained, properly closed, and promptly
returned to a drum reconditioner or
disposed of properly.
RESPIRATORY PROTECTION:
No respiratory protection is normally
required.
If user operations generate an oil mist,
determine if airborne concentrations are
below the OSHA Permissible Exposure
Limit (PEL) of 5 mg/m3 for mineral oil
mist. If not, wear a NIOSH approved
respirator that provides adequate
protection from the measured
concentrations of this material. For
air-purifying respirators use a
particulate cartridge.
Use a positive pressure, air-supplying
respirator if there is potential for
uncontrolled release, exposure levels are
not known, or other circumstances
where air-purifying respirators may not
provide adequate protection.
Section 9: Physical And
Chemical Properties
APPEARANCE AND ODOR:
Clear colorless to pale yellow liquid.
PH:
Not Available
Section 8. Exposure Controls/
Personal Protection
VAPOR PRESSURE:
GENERAL CONSIDERATIONS:
VAPOR DENSITY (Air =1):
Consider the potential hazards of this
material (see Section 3), applicable
exposure limits, job activities, and other
substances in the work place when
designing engineering controls and
selecting personal protective equipment.
If engineering controls or work practices
are not adequate to prevent exposure to
harmful levels of this material, the
personal protective equipment listed
below is recommended. The user should
read and understand all instructions and
limitations supplied with the equipment
since protection is usually provided for a
limited time or under certain
circumstances.
ENGINEERING CONTROLS:
Use in a well-ventilated area.
PERSONAL PROTECTIVE EQUIPMENT:
EYE/FACE PROTECTION:
No special eye protection is normally
required. Where splashing is possible,
wear safety glasses with side shields as
a good safety practice.
SKIN PROTECTION:
No special protective clothing is normally
required. Where splashing is possible,
select protective clothing depending on
operations conducted, physical
requirements and other substances.
Suggested materials for protective
gloves include: Nitrile Rubber, Silver
Shield, Viton.
<0.01 mmHg @ 100°F
>1
BOILING POINT:
>600°F (>315° C)
SOLUBILITY:
Soluble in hydrocarbons, insoluble in
water
FREEZING POINT
NA
MELTING POINT
NA
SPECIFIC GRAVITY:
0.85-0.87 @ 15.6 °C/15.6°C
VOLATILE ORGANIC COMPOUNDS (VOC):
2.9% weight (Approximate)
VISCOSITY:
18.7 cST - 105 cST @40°C
Section 11. Toxicological
Information
IMMEDIATE HEALTH EFFECTS
EYE IRRITATION:
The mean 24-hour Draize eye irritation
score in rabbits is 4.0/110.
SKIN IRRITATION:
For a 24-hour exposure, the
Primary Irritation Score (PIS) in
rabbits is: 0.2/8.0.
SKIN SENSITIZATION:
This material did not cause skin
sensitization reactions in a Buehler
guinea pig test.
ACUTE DERMAL TOXICITY:
The 24 hour(s) LD50 in the rabbit is
>5g/kg.
ACUTE ORAL TOXICITY:
The LD50 in the rat is >5 g/kg.
ACUTE INHALATION TOXICITY:
The acute inhalation toxicity hazard is
based on evaluation of data for similar
materials or product components.
GENETIC TOXICITY:
This product gave negative results in the
following mutagenicity assays:
Microbial/Microsome Reverse Mutation
Assay.
ADDITIONAL TOXICOLOGY INFORMATION:
This product contains petroleum base
oils which may be refined by various
processes including severe solvent
extraction, severe hydrocracking, or
severe hydrotreating. None of the oils
requires a cancer warning under the
OSHA Hazard Communication Standard
(29 CFR 1910.1200). These oils have not
been listed in the National Toxicology
Program (NTP) Annual Report nor have
they been classified by the International
Agency for Research on Cancer (IARC)
as; carcinogenic to humans (Group 1),
probably carcinogenic to humans
(Group 2A), or possibly carcinogenic to
humans (Group 2B).
Section 10. Stability And
Reactivity
Section 12. Ecological
Information:
CHEMICAL STABILITY:
EXOTOXICITY
This material is considered stable under
normal ambient and anticipated storage
and handling conditions of temperature
and pressure.
INCOMPATIBILITY WITH
OTHER MATERIALS:
May react with strong oxidizing agents,
such as chlorates, nitrates, peroxides,
etc.
HAZARDOUS DECOMPOSITION PRODUCTS:
None known (None expected)
HAZARDOUS POLYMERIZATION:
Hazardous polymerization will not occur.
Ten 96 hour(s) LC50 for rainbow trout
(Oncorhynchus mykiss) is >1000 mg/l.
ENVIRONMENTAL FATE
READY BIODEGRADABILITY:
This material is not expected to be
readily biodegradable.
Section 13. Disposal
Considerations
Oil collection services are available for
used oil recycling or disposal. Place
contaminated materials in containers
and dispose of in a manner consistent
2
with applicable regulations. Contact your
sales representative or local
environmental or health authorities for
approved disposal or recyling methods.
Section 14. Transportation
Information
The description shown may not apply to
all shipping situations. Consult 49CFR,
or appropriate Dangerous Goods
Regulations, for additional description
requirements (e.g., technical name) and
mode-specific or quantity-specific
shipping requirements.
DOT SHIPPING NAME:
Not regulated as a hazardous material for
transportation under 49 CFR
DOT HAZARD CLASS:
Not Applicable
DOT IDENTIFICATION NUMBER:
Not Applicable
DOT PACKING GROUP:
Not Applicable
Section 15. Regulatory
Information
SARA 311/312 CATEGORIES:
1.
2.
3.
4.
Immediate (Acute) Health Effects:
Delayed (Chronic) Health Effects:
Fire Hazard:
Sudden Release of
Pressure Hazard:
5. Reactivity Hazard:
REGULATORY LISTS SEARCHED:
4_I1=IARC Group 1
4_I2A=IARC Group 2A
4_I28B=IARC Group 2B
05=NTP Carcinogen
06-OSHA Carcinogen
09-TSCA 12(b)
10=TSCA Section 4
11=TSCA Section 8(a) CAIR
12=TSCA Section 8(a) PAIR
13=TSCA Section 8(d)
15=SARA Section 313
16=CA Proposition 65
17=MA RTK
18=NJ RTK
19=DOT Marine Pollutant
20=PA RTK
21=TSCA Section 5(a)
25=CAA Section 112 HAPs
26=CWA Section 311
28=CWA Section 307
30=RCRA Waste P-List
31-RCRA Waste U-List
32=RCRA Appendix VIII
No components of this material were
found on the regulatory lists above.
No
No
No
No
No
CHEMICAL INVENTORIES:
AUSTRALIA: All the components of this
material are listed on the Australian
Inventory of Chemical Substances
(AICS).
KOREA: All the components of this
product are on the Existing Chemicals
List (ECL) in Korea.
PHILIPPINES: All the components of this
product are listed on the Philippine
Inventory of Chemicals and Chemical
Substances (PICCS).
CANADA: All the components of this
material are on the Canadian Domestic
Substances List (DSL).
EUROPEAN UNION: All the components
of this material are in compliance with
the EU Seventh Amendment Directive
92/32/EEC.
UNITED STATES: All of the components
of this material are on the Toxic
Substances Control Act (TSCA) Chemical
Inventory.
NEW JERSEY RTK CLASSIFICATION:
Under the New Jersey Right-to-Know Act
L. 1983 Chapter 315 N.J.S.A.34:5A-1 et.
seq., the product is to be indentified as
follows: PETROLEUM OIL
WHMIS CLASSIFICATION:
This product is not considered a
controlled product according to the
criteria of the Canadian Controlled
Products Regulations.
Section 16. Other Information
NFPA RATINGS:
Health: Flammability:
0
1
Reactivity:
0
HMIS RATINGS:
Health: Flammability: Reactivity
1
1
0
(0-Least, 1-Slight, 2-Moderate, 3-High,
4-Extreme, PPE:-Personal Protection
Equipment Index recommendation, *Chronic Effect Indicator). These values
are obtained using the guidelines or
published evaluations prepared by the
National Fire Protection Association
(NFPA) or the National Paint and Coating
Association (for HMIS ratings).
Prepared according to the OSHA Hazard
Communication Standard (29 CFR
1910.1200) and the ANSI MSDS
Standard (Z400.1).
The above information is based on the
data of which we are aware and is
believed to be correct as of the date
hereof. Since this information may be
applied under conditions beyond our
control and with which we may be
unfamiliar and since data made available
subsequent to the date hereof may
suggest modifications of the information,
we do not assume any responsibility for
the results of it use. This information is
furnished upon condition that the person
receiving it shall make his own
determination of the suitability of the
material for his particular purpose.
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement