ADS | COM-IDS(RS)-BM1-EN | Install guide | ADS COM-IDS(RS)-BM1-EN Install guide

install guide
FLC-IDS(RS)-BM1-EN
Document number
Revision Date
20130523
fiRmware
FLC-IDS(RS)-BM1
hardware
FLRSBM1
accessories
PROGRAMMING CABLE FLPROG (REQUIRED)
FLRF1/2 (OPTIONAL)
CARLINK ASCL2 (OPTIONAL)

NOTICE The manufacturer will accept no responsability for any electrical
damage resulting from improper installation of this product, be that either
damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully
before beginning any work.
Automotive Data Solutions Inc. © 2013
BEFORE INSTALLATION
1- Connect module to computer
2- Login to Weblink account
3- Flash firmware to module (module is not preloaded with firmware)
4- Use accessories accordingly (accessories are sold separately)
www.flashlogic.com
Page 2 of 15
• 20130523
VEHICLE LIST - 1 OF 1
FEATURES
REMOTE START FROM OEM REMOTES
SECURE TAKEOVER**
DATA IMMOBILIZER BYPASS
ARM OEM ALARM
DISARM OEM ALARM
DOOR LOCK
DOOR UNLOCK
PRIORITY UNLOCK
TRUNK/HATCH RELEASE
PARKING LIGHT CTRL
RAP SHUTDOWN CTRL
TACHOMETER STATUS MONITORING
BRAKE PEDAL STATUS MONITORING
VSS STATUS MONITORING
DOOR STATUS MONITORING
TRUNK STATUS MONITORING
HOOD STATUS MONITORING*
08-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
3 Series PTS AT
06-11 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5 Series PTS AT
05-10 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
6 Series PTS AT
05-10 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1M PTS AT
11
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
M3 PTS AT
08-12 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
M5 PTS AT
06-10 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
M6 PTS AT
06-10 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
X1 PTS AT
12-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
X5 PTS AT
08-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
X5 Diesel PTS AT
08-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
X5 M PTS AT
10-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
X6 PTS AT
08-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
X6 M PTS AT
10-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Z4 PTS AT
09-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Clubman PTS AT
08-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Cooper PTS AT
07-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Cooper Convertible PTS AT
08-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Countryman PTS AT
11-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Coupe PTS AT
12-13 1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Roadster PTS AT
12-13 1
* If equipped with a factory hood switch.
** If equipped with an electric E-brake and it is activated, vehicle will shudown when a door is opened during RS sequence.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
FLC-IDS(RS)-BM1-EN
INSTALL TYPE
MAKE
BMW
MINI
Automotive Data Solutions Inc. © 2013
GLOW PLUG STATUS MONITORING
YEAR
1 Series PTS AT
POWER LIFTGATE
MODEL
NOTES
I This firmware covers Automatic Transmission
(AT) vehicles only.
•
www.flashlogic.com
Page 3 of 15
• 20130523
BOX CONTENTS - 1 OF 1
BOX CONTENTS
MODULE
LED 1
M
N
10 PIN WHITE CONNECTOR
T-HARNESS 1
LED 2
L
K
PROGRAMMING
BUTTON
A
12 PIN BLACK CONNECTOR
J
I
B
H
C
G
AFTERMARKET HOOD SWITCH AND CABLE
D
E
F
T-HARNESS 2
EXPANSION PACK
XP LED 1
STICKER 1
XP LED 2
O
STICKER 2
EXPANSION CABLE
P
ACCESSORIES (SOLD SEPARATELY)
RF KIT (OPTIONAL)
PROGRAMMING CABLE (REQUIRED)
COMPATIBLE MODELS ONLY
TELEMATICS DEVICE (OPTIONAL)
COMPATIBLE MODELS ONLY
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
Page 4 of 15
• 20130523
MODULE INSTALLATION PROCEDURE - 1 OF 1
01
02
START vehicle. Verify all vehicle
functionalities. If the vehicle displays error
messages or any malfunction: stop the
installation and service the vehicle.
07
Turn ignition to OFF position. Remove keyfob
from keyport.
08
Connect and secure every connector to the
vehicle, as shown in STEP 1 of the WIRING
DIAGRAM.
13
Connect the P connector to the module, as
shown in STEP 3 of the WIRING DIAGRAM.
P
WARNING: Any vehicle harness that is
disconnected during installation, must be
re-connected before performing any system
tests. Failure to comply will result in vehicle
displaying error messages. An OEM scantool
will be required to clear the error messages.
14
If required, connect a compatible RF Kit, as
shown in STEP 4 of the WIRING DIAGRAM.
RF
F
03
Verify all keyfob functionalities (Door Lock,
Door Unlock, Trunk Release and Comfort
Access System if equipped).
09
04
Insert the expansion pack into module.
10
WARNING: If the vehicle displays error
messages or any malfunction, stop the
installation, verify every connection and if the
problem persists, call technical support.
16
If the vehicle is not equipped with a factory
hood switch, install an aftermarket hood
switch as shown in STEP 4 of the WIRING
DIAGRAM.
05
Use the EXPANSION CABLE to connect the A
connector to the module and the O connector
to the expansion pack.
11
Turn ignition to OFF position. Remove keyfob
from keyport.
17
Put sticker 1 on a clean and visible surface
in the engine bay and put sticker 2 under the
dashboard near the OBDII connector.
Connect the module to the computer with the
programming cable and flash the module with
the latest firmware. (F port)
12
Connect the C connector to the module, as
shown in STEP 2 of the WIRING DIAGRAM.
18
Module installation procedure completed.
O
START vehicle. Verify all vehicle
functionalities.
15
I
If required, connect a compatible Telematics
Device, as shown in STEP 4 of the WIRING
DIAGRAM.
A
06
C
F
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
Page 5 of 15
• 20130523
TYPE 1 - WIRING DIAGRAM - 1 OF 1
STEP 1:
CONNECT THE FOLLOWING TO THE VEHICLE
START THE VEHICLE WITH THE OEM KEYFOB
TO TEST THE CONNECTIONS
MODULE
N
M
L
K
J
I
H
G
O
A
B
C
WARNING
1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4
2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1
A1
D
BRAKE SWITCH
4
3
2
1
A1
A2
BRAKE HARNESS
P
E F
COMFORT ACCESS SYSTEM MODULE
RELAY
MINI: BEHIND INSTRUMENT PANEL, DRIVER SIDE
BMW: UNDER DASH, DRIVER SIDE
STEP 2:
CONNECT THE FOLLOWING TO THE MODULE
C
C1
BLACK 20 PIN
B1
B1
B1 CONNECTOR
B2 HARNESS
STEP 3:
CONNECT THE FOLLOWING TO THE MODULE
B2
P
RELAY
WHITE 10 PIN
C1
C1 CONNECTOR
WARNING:
THESE CONNECTORS HAVE TWO
[2X] LOCKING MECHANISMS.
INSERT THE CONNECTOR IN ITS
HOUSING AND APPLY GENTLE
PRESSURE ON BOTH EXTREMITIES
TO SECURE THE CONNECTION.
(TWO AUDIBLE CLICKS WILL BE HEARD.)
C2
C2 HARNESS
STEP 4:
CONNECT THE FOLLOWING IF REQUIRED
H
07 GRAY/WHITE - HOOD STATUS (-) INPUT
08 GRAY/BLACK (NC)
IF NOT EQUIPPED
WITH AN OEM HOOD SWITCH,
INSTALL AN AFTERMARKET HOOD SWITCH
AFTERMARKET HOOD SWITCH (-)
F
BLACK 4 PIN - RF CABLE
RF KIT
I
BLUE 4 PIN - TELEMATIC CABLE
Automotive Data Solutions Inc. © 2013
TELEMATIC
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
Page 6 of 15
• 20130523
MODULE PROGRAMMING PROCEDURE - 1 OF 1
01
LED 1 is solid RED. Insert keyfob 1 into
keyport.
07
Remove keyfob 1 from keyport.
13
LED 1 will turn solid GREEN for 2 seconds.
02
Within 10 seconds, LED 1 will flash GREEN
once (1x).
08
WARNING: Follow steps 4, 3, 2 as shown in the
wiring diagram to disconnect the module from
the vehicle.
14
Remove keyfob 1 from keyport.
03
Remove keyfob 1 from keyport.
09
Connect module to computer and proceed
with KLON programming.
15
Module Programming Procedure completed.
04
LED 1 will turn solid RED. Wait 5 seconds.
10
WARNING: Follow steps 2, 3, 4 as shown in
the wiring diagram to connect the module to
the vehicle.
05
Insert keyfob 1 into keyport.
11
LED 1 will turn solid RED.
06
Within 10 seconds, LED 1 will flash GREEN
rapidly.
12
Insert keyfob 1 into keyport.
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
instaLLation checKList - 1 OF 2
Page 7 of 15
• 20130523
checKList
01
WARNING: Vehicle engine will start many times. Test in a well ventillated area.
02
Open driver door window for easy vehicle access.
03
Close all vehicle doors, hood and trunk.
04
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?


YES: Go to step 5.
05
Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connection, repeat step 4 and call technical support if the problem persist.
Question 2: Does the vehicle shut down?


YES: Go to step 6.
06
Unlock and open driver door.
07
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
NO: Repeat step 5. If problem persists, push vehicle start button once [1x] to shut down the vehicle and call technical support.
Question 3: Does the vehicle remote start?


YES: The module does NOT detect the door signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support.
08
Open hood.
NO: Go to step 8.
Question 4: Is the orange warning sticker "Sticker 1" placed under the hood?


YES: Leave hood open and go to step 9.
09
Close all doors.
10
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
NO: Put the mandatory orange warning sticker "Sticker 1", leave hood open and go to step 9.
Question 5: Does the vehicle remote start?


YES: Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Go to Question 6.
NO: Go to step 11.
Question 6: Is the vehicle equipped with a factory hood switch? (Inside hood latch)


YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support.
11
Close hood.
12
Enter vehicle. Do NOT press brake pedal.
13
Close all doors.
14
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
15
Wait for the vehicle to start.
16
Press brake pedal.
NO: Install the mandatory hood switch included in the kit. Repeat installation checklist.
Question 7: Does the vehicle shut down?


YES: Go to step 17.
17
Apply parking brake.
18
Exit vehicle.
NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical
support.
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
instaLLation checKList - 2 OF 2
Page 8 of 15
• 20130523
checKList
19
Close all doors.
20
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
21
Wait for the vehicle to start.
Question 8: Is the vehicle equipped with Comfort Access System ?


YES: Touch exterior driver door handle to unlock door using Comfort Access System. Within 45 seconds, go to step 22.
22
Open driver door.
NO: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 22.
Question 9: Does the vehicle shut down?

YES: For Z4, X5, X6: Go to step 25.
YES: For 1, 3, 5, 6, X1: The module does NOT detect the parking brake signal or the unlock signal from the vehicle communication network. Call technical support.

NO: For Z4, X5, X6: The module does NOT detect the parking brake signal correctly from the vehicle communication network. Call technical support.
NO: For 1, 3, 5, 6, X1: Go to step 23.
23
Press and release brake pedal.
24
Push vehicle start button once [1x] to shut down the vehicle.
25
Installation checklist completed.
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1
>>
NOTE: In Valet Mode, the Remote starter is not
functional. Keyless entry, Lock and Unlock will
remain functional. See RF kit user manual for
alternate valet mode programming.
06
Remove keyfob from keyport.
01
Insert keyfob into keyport.
07
Valet Mode Programming Procedure
completed.
02
Time restriction. Complete next step within 5
seconds.
>>
To exit valet mode: repeat steps 1 to 6.
03
STOP ACC
ON START
Page 9 of 15
• 20130523
Cycle ignition ON five times [5x OFF/ON]
rapidly. Parking Light will flash once [1x].
ENGINE
START
STOP
04
05
Wait, Parking Light will flash once [1x] to
indicate that the valet mode is ON or twice [2x]
to indicate that the valet mode is OFF.
Turn ignition to STOP position.
STOP ACC
ON START
ENGINE
START
STOP
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
aFteRmaRKet Remote PRogRamming - 1 OF 1
Page 10 of 15
• 20130523
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
aFteRmaRKet Remote PRogRamming:
notes
I All aftermarket remotes must be programmed to the
RF-Kit.
Refer to the RF-Kit user guide for aftermarket remote
features and programming procedures.
Automotive Data Solutions Inc. © 2013
Page 11 of 15
• 20130523
MODULE NAVIGATION PROCEDURE - 1 OF 1
>>
It is mandatory to exit the Module Navigation
at the end of this procedure. Failure to exit the
Module Navigation will drain vehicle battery.
To exit the Module Navigation at any time:
Follow STEP 13.
04
>>
Module must be programmed to the vehicle.
05
>>
Use the Module Navigation Chart on the next
page.
06
Set ignition to OFF position.
07
TO ACCESS THE MENUS: Press and hold
programming button until LED 1 turns solid
GREEN.
08
IN THE MENUS: Press the programming
button as many times as the menu number
indicates. LED 1 will flash GREEN an equal
amount of times continuously.
09
01
STOP ACC
ON START
TO ACCESS THE OPTIONS: Press and hold
programming button until LED 1 turns solid
RED.
10
IN THE OPTIONS: Press the programming
button as many times as the option number
indicates. LED 1 will flash RED an equal
amount of times continuously.
11
TO ACCESS THE SETTINGS: Press and hold
programming button until LED 1 turns solid
GREEN.
12
Configure every other setting and proceed to
step 13.
[Z]
LED 1 will flash GREEN as many times as
the current (or default) setting number,
continuously.
13
MANDATORY: EXIT MODULE NAVIGATION.
Press and hold programming button for 7
seconds. LED 1 will flash RED rapidly. Release
programming button. LED 1 will turn OFF.
[Z]
IN THE SETTINGS: Press the programming
button as many times as necessary to access
your setting. LED 1 will flash GREEN an equal
amount of times continuously.
14
Module navigation completed.
To return to the MENUS: exit the Module
Navigation and redo the Module Navigation
Procedure.
>>
Failure to exit the Module Navigation will drain
vehicle battery.
[Y]
To save and return to the OPTIONS: Press and
hold programming button until LED 1 turns
solid RED.
[Y]
LED 1 will flash RED as many times as the
current option number continuously.
ENGINE
START
STOP
02
03
[X]
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
Page 12 of 15
• 20130523
[Y] oPtions
[X] menus
moDuLe navigation chaRt:
notes
I Default settings are listed in bold.
01
oFF
02
ON
01
oFF
02
ON
01
oFF
02
ON
01
oFF
02
ON
01
enabLe
02
DISABLE*
01
45 sec
02
90 SEC
03
03 MIN
04
04 MIN
01
DISABLE
02
N/A
03
LOCK + UNLOCK + LOCK
04
LocK + LocK + LocK
01
03 MIN
02
05 MIN
03
10 MIN
04
15 MIN
05
25 MIN
06
30 MIN
07
35 MIN
08
15 min
01
02 sec
02
05 SEC
03
08 SEC
04
10 SEC
05
15 SEC
06
20 SEC
07
25 SEC
08
30 SEC
10-15 N/A
01
N/A
01
01
N/A
01
II Make sure the option is covered on the vehicle before
attempting to change the setting.
02
03
04
05
06
07
01
[Z] settings
moDuLe navigation chaRt - 1 OF 1
DISARM/UNLOCK BEFORE START
RELOCK AFTER START
RELOCK AFTER SHUTDOWN
FORCE UNLOCK ALL ON FIRST PRESS
TAKEOVER
SECURE TAKEOVER DELAY
FACTORY KEYLESS RS SEQUENCE
CONFIGURATION
08
09
02-07 Technical Support only
MODULE RUN TIME
WAIT TO START DELAY
N/A
*Vehicle will shudown when a door is opened.
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
www.flashlogic.com
[X] numbeR oF
PaRKing Light
FLashes
Diagnostic
Remote staRteR eRRoR coDes - 1 OF 1
I WARNING: The following applies only when the parking
lights are connected and supported by the system.
03
Foot brake is ON.
04
Hood is open.
II After a remote starter failure, the parking lights will flash
[X] number times to indicate an error code. See table.
05
Engine tach signal is lost.
06
System is in Valet Mode.
07
Vehicle is moving (VSS).
08
Glow plug timeout error.
09
RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
10
N/A
11
N/A
12
N/A
13
N/A
14
N/A
15
N/A
16
CAN communication failure during RS sequence.
Remote staRteR eRRoR coDes:
notes
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
Page 13 of 15
• 20130523
www.flashlogic.com
I
II
III
DURING PROGRAMMING
DURING REMOTE START
WITH IGNITION OFF
Automotive Data Solutions Inc. © 2013
Diagnostic
test moDuLe
LeD 1 status
moDuLe Diagnostics - 1 OF 1
Flashing RED
Missing/wrong information from firmware or vehicle.
Solid RED
Module waiting for more vehicle information.
Flashing GREEN
Additional steps required to complete module programming.
Solid GREEN then OFF
Module correctly programmed.
OFF
No activity or module already programmed.
Flashing RED
Module incorrectly programmed.
Solid RED
Module incorrectly programmed.
Flashing GREEN
Module correctly programmed and operational.
Solid GREEN then OFF
Reset in progress.
OFF
Invalid ground when running status from remote starter.
Flashing RED
Module incorrectly programmed or connected.
Solid RED
Module not programmed. Waiting for more vehicle information.
Flashing GREEN
False ground when running status from remote starter.
Solid GREEN then OFF
Reset in progress.
OFF
Module at rest and ready for a remote start sequence.
FLC-IDS(RS)-BM1-EN
Page 14 of 15
• 20130523
www.flashlogic.com
MODULE RESET PROCEDURE - 1 OF 1
01
Disconnect all connectors from module except
the BLACK 20-PIN connector.
07
Reconnect all connectors.
02
Disconnect the BLACK 20-PIN connector.
08
Repeat programming procedure.
03
PRESS AND HOLD programming button while
connecting the BLACK 20-PIN connector.
>>
Failure to follow procedure may result with a
DTC or a CHECK ENGINE error message.
04
Wait, LED 1 will flash RED. RELEASE
programming button.
05
LED 1 will turn RED for 2 seconds.
06
Module RESET completed.
Automotive Data Solutions Inc. © 2013
FLC-IDS(RS)-BM1-EN
Page 15 of 15
• 20130523
www.flashlogic.com
Download PDF