Sharp | R-880B | Service manual | Sharp R-880B Service manual

R-880B
SERVICE MANUAL
S9839R880BPM/
DOUBLE GRILL
CONVECTION
MICROWAVE OVEN
COOK
HELP
Info Display
MULTI
COOK
REHEAT
SENSOR
HELP
Fresh
Vegetables
Frozen
Vegetables
MIX
EASY
DEFPST
ACTION
Reheat Pie
Jacket
Potato
Rice
Pasta
R-880B
GRILL CONVEC
REHEAT
POWER
MIXLEVEL
LESS
DOUBLE GR
MODEL
CONVENIENCE
/PIZZA
SENSOR INSTANT
MORE
ILL CONVEC
TIO
1 2 3 4 5
6 7 8 9 0
N
40˚ C
70˚ C
130˚ C
150˚ C
160˚ C
180˚ C
200˚ C
220˚ C
230˚ C
250˚ C
STOP
CLEAR
Sensor
CLOCK INSTANT COOK
START
In interests of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.
TABLE OF CONTENTS
Page
CAUTION, MICROWAVE RADIATION.................................................................................................... 1
WARNING .................................................................................................................................................1
PRODUCT SPECIFICATIONS ................................................................................................................ 2
GENERAL INFORMATION....................................................................................................................... 2
APPEARANCE VIEW .............................................................................................................................. 3
OPERATION SEQUENCE....................................................................................................................... 4
FUNCTION OF IMPORTANT COMPONENTS ....................................................................................... 8
SERVICING .............................................................................................................................................. 8
TROUBLESHOOTING GUIDE ............................................................................................................... 10
TEST PROCEDURE .............................................................................................................................. 12
TOUCH CONTROL PANEL ASSEMBLY .............................................................................................. 20
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE .................................................. 26
MICROWAVE MEASUREMENT ........................................................................................................... 33
WIRING DIAGRAM ................................................................................................................................ 34
PICTORIAL DIAGRAM .......................................................................................................................... 38
POWER UNIT CIRCUIT ......................................................................................................................... 39
CONTROL PANEL CIRCUIT .................................................................................................................. 40
PRINTED WIRING BOARD .................................................................................................................... 41
PARTS LIST .......................................................................................................................................... 42
SHARP CORPORATION
R-880B
R-880B
SERVICE MANUAL
PRODUCT SPECIFICATIONS
GENERAL INFORMATION
DOUBLE GRILL
CONVECTION
MICROWAVE OVEN
APPEARANCE VIEW
R-880B
GENERAL IMPORTANT INFORMATION
This Manual has been prepared to provide Sharp Corp. Service
engineers with Operation and Service Information.
OPERATING SEQUENCE
It is recommended that service engineers carefully study the entire
text of this manual, so they will be qualified to render satisfactory
customer service.
FUNCTION OF IMPORTANT
COMPONENTS
CAUTION
MICROWAVE RADIATION
SERVICING AND
TROUBLESHOOTING GUIDE
Service engineers should not be exposed to the microwave
energy which may radiate from the magnetron or other microwave generating devices if it is improperly used or connected.
All input and output microwave connections, waveguides, flanges
and gaskets must be secured. Never operate the device without
a microwave energy absorbing load attached. Never look into
an open waveguide or antenna while the device is energized.
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is not any other visible damage with the oven.
Servicing and repair work must be carried out only by trained
service engineers.
TEST PROCEDURE
TOUCH CONTROL PANEL
COMPONENT REPLACEMENT
AND ADJUSTMENT PROCEDURE
MICROWAVE MEASUREMENT
WIRING DIAGRAM
All the parts marked "*" on parts list are used at voltages more than
250V.
Removal of the outer wrap gives access to potentials above 250V.
All the parts marked "∆" on parts list may cause undue microwave
exposure, by themselves, or when they are damaged, loosened or
removed.
Never operate the Top and/ or Bottom heater with the oven
outer cabinet removed. (Because air flow is eliminated, and the
excess heat generated on adjacent components). It can cause
permanent damage or a fire.
SHARP CORPORATION
OSAKA, JAPAN
1
PARTS LIST
R-880B
PRODUCT DESCRIPTION
SPECIFICATION
ITEM
DESCRIPTION
Power Requirements
Power Consumption
Power Output
Grill heater Power Output (Top heater)
Bottom heater Power Output
Case Dimensions
Cooking Cavity Dimensions
Turntable diameter
Control Complement
220 Volts
50 Hertz
Single phase, 3 wire earthed
Microwave cooking 1.6 kW
Top Heater mode
1.3 kW
Grill cooking
Bottom heater mode
0.9 kW
Top and Bottom heater mode
2.1 kW
Convection cooking 2.1 kW
900 W nominal of RF microwave energy (measured by method of IEC 705)
Operating frequency 2450 MHz
1200 W (600 W x 2)
800 W
Width
520 mm
Height 309 mm including foot
Depth
502 mm
Width
352 mm
Height 189 mm
Depth
368 mm
325 mm
Touch Control System
Clock (1:00 - 12:59) / Timer (0 - 99 minutes and 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
100% ................................................... Full power throughout the cooking time
70% ..................................................................... approx. 70% of FULL Power
50% ..................................................................... approx. 50% of FULL Power
30% ..................................................................... approx. 30% of FULL Power
10% ..................................................................... approx. 10% of FULL Power
Mix cooking
High Mix Top Grill ............................... Top heater with 70% microwave power
Low Mix Top Grill ................................ Top heater with 50% microwave power
High Mix Bottom Grill ........................ Bottom heater with 70% microwave power
Low Mix Bottom Grill ......................... Bottom heater with 10% microwave power
Grill Cooking ............... Top heater mode/ Buttom heater mode/ Top and Buttom
heater mode
Convection cooking.......................................... 40˚C to 250˚C temperature control
Set Weight
HELP pad, MULTI COOK pad, CONVIENIENCE/PIZZA pad
REHEAT SENSOR pad, EASY DEFROST pad
SENSOR INSTANT ACTION pads, MIX pad, GRILL pad, CONVEC pad
REHEAT pad, LESS (")/MORE (') pads, POWER LEVEL pad
NUMBER AND TEMPERATURE pads, STOP/CLEAR pad
CLOCK pad, INSTANT COOK/START pad
Approx. 20 kg
GENERAL INFORMATION
WARNING
THIS APPLIANCE MUST BE EARTHED
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
GREEN-AND-YELLOW
BLUE
BROWN
: EARTH
: NEUTRAL
: LIVE
2
R-880B
APPEARANCE VIEW
OVEN
1. Oven lamp
2. Top heaters (Grill heaters)
3. See through door
4. Door hinges
5. Door safety latches
6. Door seals and sealing surfaces
7. Bottom heater
8. Oven cavity
9. Turntable motor shaft
10.Ventilation openings
11.Waveguide cover
12.Door opening button
Turntable
13.Control panel
support
14.Digital display
15.Power supply cord
16.Outer cabinet
17.Menu label
Bottom
heater
4
2
u
0
t
r
0
1
5
8 9
e
q
y
3
6
0
High rack
7
5
0
w
NOTE:
1. Ensure that the bottom heater is in the lowest
position as shown the figure, as it is possible
to move it up and down to help with cleaning.
2. Place the turntable support over the turntable motor shaft on the floor of the cavity.
Low rack
3. Then place the turntable on to the turntable
support.
Turntable
Turntable
motor shaft
TOUCH CONTROL PANEL
1. TOP HEATER SYMBOL
The symbol will light when the top heater is in use.
2. BOTTOM HEATER SYMBOL
The symbol will light when the bottom heater is in use.
3. CONVECTION SYMBOL
1
The symbol will light during convection cooking.
COOK
INDICATOR
HELP
A. HELP PAD
2
Press to select auto start, information guide on/off, child lock,
Info Display
3
demonstration modes or info on pads.
Press to obtain cooking information.
A
HELP
B. MULTI COOK PAD
Press to select Multi Cook mode.
MULTI
CONVENIENCE
C
B
C. CONVIENIENCE/PIZZA PAD
/PIZZA
COOK
Press to select 6 popular menus.
EASY
REHEAT
E
D
SENSOR
DEFPST
D. REHEAT SENSOR PAD
Press to select 3 popular Re-heat menus.
E. EASY DEFROST PAD
SENSOR INSTANT ACTION
Press to defrost meat by entering weight.
Fresh
Jacket
Reheat Pie
Vegetables
Potato
F. SENSOR INSTANT ACTION PAD
F
Frozen
Press once to cook or reheat 6 popular menus.
Rice
Pasta
Vegetables
G. MIX PAD
I
Press to select Mix cooking.
G
MIX
GRILL CONVEC REHEAT
J
H. GRILL PAD
H
Press to select Grill cooking.
L
POWER
I. CONVEC PAD
LESS
LEVEL
MORE
Press to select Convection cooking.
K
J. REHEAT PAD
Press to reheat the oven prior to cooking.
M
K. LESS (")/MORE (') pads
Press to adjust the doneness of food in one minute increments
during cooking or to increase/ decrease the time whilst pro- N
STOP
INSTANT COOK
CLOCK
gramming the automatic operations.
START
CLEAR
P
L. POWER LEVEL PAD
O
Press to select microwave power setting. If not pressed, HIGH
is automatically selected.
M. NUMBER AND TEMPERATURE PADS
O. CLOCK PAD
Press to enter cooking times, clock time, convection temperaPress to set clock time.
ture, weight or quantity of food.
P. INSTANT COOK/START PAD
N. STOP/CLEAR PAD
Press once to cook for 1 minute on HIGH or
Press to clear during programming. Press once to stop operaincrease by 1 minute multiples each time this
tion of oven during cooking; Press twice to cancel cooking
pad is pressed during manual cooking. Press
programme.
to start oven after setting programs.
1 2 3 4 5
6 7 8 9 0
3
40˚ C
70˚ C
130˚ C
150˚ C
160˚ C
180˚ C
200˚ C
220˚ C
230˚ C
250˚ C
R-880B
OPERATION SEQUENCE
OFF CONDITION
Closing the door activates the 1st. latch switch and 2nd.
interlock relay control switch.
IMPORTANT:
When the oven door is closed, the contacts COM-NC
of the monitor switch must be open. When the microwave oven is plugged in a wall outlet (220V 50Hz),
the line voltage is supplied to the noise filter and the
control unit.
Contact
1st. latch switch
2nd. interlock relay
control switch
Monitor Switch
COM-NO
Condition
During
Oven Door
Cooking Open(No cooking)
Closed
Opened
COM-NO
Closed
Opened
COM-NC
Opened
Closed
The circuit to the high voltage transformer, fan motor, oven
lamp and turntable motor are cut off when the 1st. latch
switch and 2nd. interlock relay control switch are made
open. Shown in the display is remaining time.
6. MONITOR SWITCH CIRCUIT
The monitor switch is mechanically controlled by the
oven door, and monitors the operation of the 1st. latch
switch and the 2nd. interlock relay RY2.
6-1. When the oven door is opened during or after the
cycle of a cooking program, the 1st. latch switch and
2nd. interlock relay control switch must open their
contacts first. After that the contacts (COM-NC) of the
monitor switch can be closed.
6-2. When the oven door is closed, the contacts (COMNC) of the monitor switch must be opened. After that
the contacts of the 1st. latch switch and 2nd. interlock
relay control switch are closed.
6-3. When the oven door is opened and the contacts of the
1st. latch switch and the 2nd. interlock relay RY2
remain closed, the fuse M10A will blow, because the
monitor switch is closed and a short circuit is caused.
Figure O-1 on page 34
1. The oven display will show " SHARP MICRO- WAVE
OVEN " .
2. Press the STOP/CLEAR pad. The oven display will
show " :
".
3. Set the clock as follows.
3-1. Press the CLOCK pad once.
3-2. Enter the time of day by perssing the number
pads.
3-3. Start the clock by pressing the CLOCK pad.
NOTE:
1. If you do not set the clock, " : " will appear on the
display. When the operation of the oven is finished, " :
" will appear on the display instead of the time of day.
2. The oven can be also used when the clock is not set.
3. When the oven door is opened, the oven lamp does not
come on.
MICROWAVE COOKING CONDITION
70% (MEDIUM HIGH), 50% (MEDIUM), 30% (MEDIUM LOW), 10% (LOW COOKING)
100% (HIGH) COOKING
Enter a desired cooking time by pressing the number pads
and start the oven by pressing START pad.
When the microwave oven is preset for variable cooking
power, the line voltage is supplied to the high voltage
transformer intermittently within a 32-second time base
through the relay contact which is coupled with the current-limiting relay RY2. The following levels of microwave
power are given.
Function sequence Figure O-2 on page 34
CONNECTED COMPONENTS
Convection motor
High voltage transformer
Grill heater (Top)
Bottom heater
Fan motor,
Oven lamp, Turntable motor
Switch
RELAY
RY1
RY2
RY3
RY4
RY5
RY6
32 sec. ON
SETTING
Approx. 100%
100%
24 sec. ON
8 sec. OFF
18 sec. ON
14 sec. OFF
12 sec. ON
20 sec. OFF
6 sec. ON
26 sec. OFF
Approx. 70%
70%
Approx. 50%
50%
1. The line voltage is supplied to the primary winding of
the high voltage transformer. The voltage is converted
to about 3.3 volts A.C. output on the filament winding
and high voltage of approximately 2000 volts A.C. on
the secondary winding.
2. The filament winding voltage (3.3 volts) heats the
magnetron filament and the high voltage (2000 volts) is
sent to the voltage doubling circuit, where it is doubled
to negative voltage of approximately 4000 volts D.C..
3. The 2450 MHz microwave energy produced in the
magnetron generates a wave length of 12.24 cm. This
energy is channelled through the waveguide (transport
channel) into the oven cavity, where the food is placed
to be cooked.
4. When the cooking time is up, a signal tone is heard and
the relays RY2 + RY5 + RY6 go back to their home
position. The circuits to the oven lamp, high voltage
transformer, fan motor and turntable motor are cut off.
5. When the oven door is opened during a cooking cycle,
the switches come to the following condition.
Approx. 30%
30%
10%
Note:
Approx. 10%
The On/Off time ratio does not exactly correspond
to the percentage of microwave power, because
approx. 2 seconds are needed for heating up the
magnetron filament.
GRILL COOKING CONDITIONS
The oven has three grill cooking condition. They are the
TOP GRILL mode, BOTTOM GRILL mode and TOP AND
BOTTOM GRILL mode.
TOP GRILL MODE
In this mode, the food is cooked by the top heaters. Press
the GRILL pad once and then enter the cooking time by
pressing the number pads. When the START pad is
pressed, the following operations occur:
Figure O-3(a) on page 35
4
R-880B
1. The relay RY3 + RY5 + RY6 are energized.
2. The numbers of the digital read-out start the count
down to zero.
3. Then the top heaters, turntable motor, oven lamp and
fan motor are energized.
4. Now, the food is grilled by the top heaters.
5. Upon completion of the selected cooking time, audible
signal sounds and the contacts of relays RY3 + RY6
are opened, then the top heaters, turntable motor and
oven lamp are de-energized. But the relay RY5 stays
closed and the fan motor operates for 5 minutes. But if
the cooking time is less than 2 minutes the relay RY5
will not stay close.
In these modes, the food is cooked by the top heaters and
the microwave energy. Press the MIX pad once for HIGH
MIX TOP GRILL mode. Press the MIX pad twice for LOW
MIX TOP GRILL mode. And then enter the cooking time
by pressing the number pads. When the START pad is
pressed, the following operations occur:
Figure O-5(a) on page 37
1. The relay RY5 + RY6 are energized.
2. The numbers of the digital read-out start the count
down to zero.
3. The turntable motor, oven lamp and fan motor are
energized.
4. The relay RY2 + RY3 are energized alternately within
a 48 seconds time base by the control unit.
5. The top heaters operate through the relay RY3 is
energized. And the high voltage transformer operates
through the relay RY2 is energized.
6. The relationship between the top heating elements and
magnetron operations are as follows.
BOTTOM GRILL MODE
In this mode, the food is cooked by the bottom heater.
Press the GRILL pad twice and then enter the cooking time
by pressing the number pads. When the START pad is
pressed, the following operations occur:
1.
2.
3.
4.
5.
Figure O-3(b) on page 35
The relay RY4 + RY5 + RY6 are energized.
The numbers of the digital read-out start the count
down to zero.
Then the bottom heater, turntable motor, oven lamp
and fan motor are energized.
Now, the food is grilled by the bottom heater.
Upon completion of the selected cooking time, audible
signal sounds and the contacts of relays RY4 + RY6
are opened, then the bottom heating elements, turntable motor and oven lamp are de-energized. But the
relay RY5 stays closed and the fan motor operates for
5 minutes. But if the cooking time is less than 2 minutes
the relay RY5 will not stay close.
36 SEC.
ON
(MICRO.)
3.
4.
5.
OFF
MICROWAVE POWER
= APPROX. 70%
ON
TOP
HEATERS
OFF
HIGH MIX TOP GRILL mode
26 SEC.
22 SEC.
ON
(MICRO.)
OFF
MICROWAVE POWER
= APPROX. 50%
ON
TOP
HEATERS
TOP AND BOTTOM GRILL MODE
In this mode, the food is cooked by both the top heaters
and bottom heater. Press the GRILL pad three times and
then enter the cooking time by pressing the number pads.
When the START pad is pressed, the following operations
occur:
1.
2.
12 SEC.
OFF
LOW MIX TOP GRILL mode
Note:
The On/Off time ratio does not exactly correspond
to the percentage of microwave power, because
approx. 2 seconds are needed for heating up the
magnetron filament.
7. Upon completion of the selected cooking time, audible
signal sounds and the contacts of relays RY2 + RY3 +
RY6 are opened, then the top heaters, high voltage
transformer, turntable motor and oven lamp are deenergized. At the end of the convection cycle, if the
cavity air temperature is above 120˚C, the circuit to
RY5 will be maintained (by the thermistor circuit) to
continue operation of the cooling fan motor until the
temperature drops below 104˚C, at which time the
relay will be de0energized, turning off the fan motor.
Figure O-3(c) on page 36
The relay RY3 + RY4 + RY5 + RY6 are energized.
The numbers of the digital read-out start the count
down to zero.
Then the top heaters, bottom heater, turntable motor,
oven lamp and fan motor are energized.
Now, the food is grilled by the top heaters and the
bottom heater.
Upon completion of the selected cooking time, audible
signal sounds and the contacts of relays RY3 + RY4 +
RY6 are opened, then the top heating elements, bottom heating element, turntable motor and oven lamp
are de-energized. But the relay RY5 stays closed and
the fan motor operates for 5 minutes. But if the cooking
time is less than 2 minutes the relay RY5 will not stay
closed.
HIGH MIX BOTTOM GRILL MODE AND LOW MIX BOTTOM GRILL MODE
In these modes, the food is cooked by the bottom heater
and the microwave energy. Press the MIX pad three (3)
times for HIGH MIX BOTTOM GRILL mode. Press the MIX
pad four (4) times for LOW MIX BOTTOM GRILL mode.
And then enter the cooking time by pressing the number
pads. When the START pad is pressed, the following
operations occur:
Figure O-5(b) on page 37
1. The relay RY5 + RY6 are energized.
2. The numbers of the digital read-out start the count
down to zero.
3. The turntable motor, oven lamp and fan motor are
GRILL MIX COOKING CONDITION
The oven will cook food by supplying grill heaters (top
heaters or Bottom heater) and microwave energy alternately within a 48 seconds time base. And the oven has
four programmed cooking mode.
HIGH MIX TOP GRILL MODE AND LOW MIX TOP
GRILL MODE
5
R-880B
energized.
4. The relay RY2 + RY4 are energized alternately within
a 48 seconds time base by the control unit.
5. The bottom heater operate through the relay RY4 is
energized. And the high voltage transformer operates
through the relay RY2 is energized.
6. The relationship between the top heating elements and
magnetron operations are as follows.
26 SEC.
NOTE:
1. In case of Automatic operations, the limitations of
power output are not carried out.
2. In case that the STOP/CLEAR pad is pressed or the
oven door is opened during cooking, the limitations of
power output are carried out after the total cooking time
beyond the specified cooking time.
3. In case of the two or more same cooking modes are
carried out, the limitations of power output are carried
out after the total cooking time beyond the specified
cooking time.
4. In case of the two or more different cooking modes are
carried out, the specified cooking time is started to
count from the point when the cooking mode is changed.
5. If the cooking mode has the power level display, the
power level is also displayed when the limitations of
power output are carried out.
22 SEC.
ON
(MICRO.)
MICROWAVE POWER
= APPROX. 50%
OFF
ON
BOTTOM
HEATER
OFF
HIGH MIX GRILL BOTTOM GRILL mode
8 SEC.
CONVECTION COOKING CONDITION
40 SEC.
PREHEATING CONDITION
Press the PREHEAT pad and then select preheating
temperature by pressing the temperature pad. When the
START pad is touched, the following operations occur:
ON
MICROWAVE POWER
= APPROX. 10%
(MICRO.)
OFF
ON
BOTTOM
HEATER
OFF
Figure O-4 on page 36
1. The coils of shut-off relays RY1+RY5+RY6 are energized, the oven lamp, cooling fan motor, turntable
motor and convection motor are turned on.
2. The coil of heater relays RY3+RY4 are energized by
the CPU unit and the main supply voltage is added to
the top and bottom heaters.
3. When the oven temperature reaches the selected
preheat temperature, the following operations occur:
3-1. The heater relays RY3+RY4 de-energized by the
CPU unit temperature circuit and thermistor, opening
the circuit to the top and bottom heaters.
3-2. The oven will continue to function for 30 minutes,
turning the top and bottom heaters on and off, as
needed to maintain the selected preheat temperature. The oven will shut-down completely after 30
minutes.
LOW MIX GRILL BOTTOM GRILL mode
Note:
The On/Off time ratio does not exactly correspond
to the percentage of microwave power, because
approx. 2 seconds are needed for heating up the
magnetron filament.
7. Upon completion of the selected cooking time, audible
signal sounds and the contacts of relays RY2 + RY4 +
RY6 are opened, then the bottom heater, high voltage
transformer, turntable motor and oven lamp are deenergized. At the end of the convection cycle, if the
cavity air temperature is above 120˚C, the circuit to
RY5 will be maintained (by the thermistor circuit) to
continue operation of the cooling fan motor until the
temperature drops below 104˚C, at which time the
relay will be de-energized, turning off the fan motor.
AUTOMATIC OPERATIONS
CONVECTION COOKING CONDITION
This oven has the following automatic operations;
MULTI COOK
CONVIENIENCE/PIZZA
EASY DEFROST
Thease will automatically compute the cooking mode and
the cooking time. And the oven will cook or defrost the food
according to the special cooking sequence.
When the preheat temperature is reached, a beep signal
will sound indicating that the holding temperature has
been reached in the oven cavity. Open the door and place
the food to be cooked in the oven. Press the CONVECTION pad and then enter the cooking temperature by
pressing the temperature pad. And then enter the cooking
time by pressing the NUMBER pads. When the START
pad is touched, the following operations occur:
1. The numbers of the digital read-out start the count
down to zero.
2. The oven lamp, turntable motor, cooling fan motor and
convection motor are energized.
3. The relays(RY3 and RY4) are energized (if the cavity
temperature is lower than the selected temperature)
and the main supply voltage is applied to the heating
element to return to the selected cooking temperature.
The top heaters and the bottom heater work in accordance with the following table while the heaters are
energized.
LIMITATIONS OF POWER OUTPUT IN MANUAL
OPERATION
After the same cooking mode is carried out for more than
the specified cooking time, the power output is automatically reduced by turning the control relays on and off
intermittently, as shown in the table below. This is to
protect the oven door against temperature rising.
Cooking mode
Microwave
100% Power
Top heaters
Bottom heater
Top browner and
Bottom browner
or Oven cooking
Specified cooking
time (minutes)
Limited power
output (%)
Time base
(seconds)
20
70
32
30
50
48
15
50
48
10 (Top)
10 (Bottom)
50
50
48
48
6
R-880B
Selected Temperature (˚C)
Top Heaters
Power (%)
3. Sensor detects moisture and humidity and calculates
cooking time and variable power.
Bottom Heater
Power (%)
250
40
40
230
220
200
40
40
30
40
40
70
180
160
20
10
70
70
150
130
70
10
10
10
70
60
40
40
10
30
AH SENSOR COOKING SEQUENCE
1. In case the AH sensor cooking condition is started, the
coil of shut-off relays (RY5+RY6) are energized, the
oven lamp and cooling fan motor are turned on, but the
power transformer is not turned on.
NOTE: The oven should not be operated on AH SENSOR
COOKING immediately after plugging in the unit.
Wait t wo minutes before cooking on AH SENSOR
COOKING CONDITION.
2. After about 16 seconds, the cook relay (RY2) is energized. The power transformer is turned on, microwave
energy is produced and first stage is started. The 16
seconds is the cooling time required to remove any
vapour from the oven cavity and sensor.
(Figure O-2)
4. Upon completion of the cooking time, the audible
signal will sound, and oven lamp, turntable motor,
cooling fan motor and convection motor are de-energized. At the end of the convection cycle, if the cavity
air temperature is above 120˚C, the circuit to (RY5) will
be maintained (by the thermistor circuit) to continue
operation of the cooling fan motor until the temperature
drops below 104˚C, at which time the relay will be deenergized, turning off the fan motor. Relay (RY1) will
however, open as soon as the convection cycle has
ended, turning off the convection fan motor.
NOTE: During this first stage, do not open the door or
touch STOP/CLEAR pad.
There is a menu which the oven operates in grill
cooking mode.
3. When the sensor detects the vapour emitted from the
food, the display switches over to the remaining cooking
time and the timer counts down to zero. At this time, the
door may be opened to stir food, turn it or season, etc.
ABSOLUTE HUMIDITY SENSOR (AH SENSOR)
COOKING CONDITION
NOTE: In case where a small quantity of food is cooked,
the oven will stop without displaying the remaining
cooking time. In case of "Reheat Pie" of Sensor
Instant Action, the relay (RY2) is turned off and
power transformer is turned off. And then the
relays (RY3 + RY4) are energized. The top and
bottom heaters are turned on.
4. When the timer reaches zero, an audible signal sounds.
The shut-off relay (RY5+RY6) and cook relay (RY2)
are de-energized and the power transformer, oven
lamp, etc. are turned off.
In case where the AH sensor is used (REHEAT SENSOR
or SENSOR INSTANT ACTION), the foods are cooked in
microwave cooking mode or grill cooking mode without
figuring time, power level or quantity. When the oven
senses enough steam from the food, it relays the information to its microprocessor which will calculate the remaining
cooking time and power level needed for best results.
When the food is cooked, water vapour is developed. The
sensor “senses” the vapour and its resistance increases
gradually. When the resistance reaches the value set
according to the menu, supplementary cooking is started.
The time of supplementary cooking is determined by experiment with each food category and inputted into the LSI.
An example of how sensor works:
FIRE SENSING FEATURE (MICROWAVE MODE)
This model incorporates a sensing feature which will stop
the oven's operation if there is a fire in the oven cavity
during microwave cooking. This accomplished by the LSI
repeatedly measures the voltage across the temperature
measurement circuit (thermistor) during it's 32-seconds
time base comparing the obtained voltage measurements.
If the most recent voltage measured is 700mV grater than
the previous voltage measured, the LSI judges it as a fire
in the oven cavity and switches off the relays to the power
transformer, fan motor turntable motor and the oven lamp.
The LSI also stops counting down. Please refer to the
following section for a more detailed description.
Operation
Please refer to the timing diagrams below.
1. The thermistor operates within a 32-seconds time base
and it is energized for three (3) seconds and off for 29
seconds. Two (2) seconds after the thermistor is
energized, the voltage across the temperature measurement circuit is sampled by the LSI and twenty one
(21) seconds after the thermistor is cut off the LSI turns
on the cooling fan for six (6) seconds.
2. The above procedure is repeated. If the difference
between the first voltage measured (in step 1) and
the voltage measured when the procedure is repeated
(step 2) is greater than 700mV the LSI makes the
1. Potatoes at room temperature. Vapour is emitted very
slowly.
MIC
RO
WA
VE
2. Heat potatoes. Moisture and humidity is emitted rapidly. You can smell the aroma as it cooks. ;
AH SENSOR
MIC
RO
WA
VE
7
R-880B
judgment that there is a fire in the oven cavity and will
switch off the relays to the power transformer, fan
motor, turntable motor and the oven lamp. The LSI
also stops counting down.
3. Once the fire sensor feature has shut the unit down, the
programmed cooking cycle may be resumed by pressing the "START" pad or the unit may be reset by
pressing the "CLEAR" pad.
ON/OFF TIME RATIO
In grill cooking, convection cooking or mix cooking, the top
heaters, bottom heater or magnetron operate whithin a 48
second time base. The following table is the ON / OFF time
ratio at each power output of the top heaters, bottom
heater or magnetron.
POWER OUTPUT
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
IMPORTANT:
During sensor cooking operation, the fire sensing
operation sequence will not begin until the AH sensor
has detected vapours and initiated a sensor cooking
cycle. This is because the operation of the convection
fan would interfere with the AH sensor's vapour detection.
0 23
24
30 32 (sec.)
64 (sec.)
6 sec.
CONVECTION
MOTOR
ON
OFF
3 sec.
THERMISTOR
ON
ON TIME
48 sec.
44 sec.
40 sec.
36 sec.
32 sec.
26 sec.
22 sec.
16 sec.
12 sec.
8 sec.
OFF TIME
0 sec.
4 sec.
8 sec.
12 sec.
16 sec.
22 sec.
26 sec.
32 sec.
36 sec.
40 sec.
OFF
ON
Sensing
Voltage OFF
Sensing the voltage across the temperature measurement circuit.
FUNCTION OF IMPORTANT COMPONENTS
be opened.
2. When the door is opened, the contacts (COM-NC)
must be closed.
3. If the oven door is opened and he contacts (COM-NO)
of the 1st. latch switch and 2nd. interlock relay (RY2)
fail to open, the fuse M10A blows immediately after
closing the contacts (COM-NC) of the monitor switch.
DOOR OPEN MECHANISM
The door can be opened by pushing the open button on the
control panel. When the open button is pushed, the switch
lever is moved upward, operating the latch head. The latch
head is moved upward and released from the latch hook.
Now, the door can be opened.
Latch Heads
CAUTION: BEFORE REPLACING A BLOWN FUSE
M10A TEST THE 1ST. LATCH SWITCH, 2ND.
INTERLOCK RELAY (RY2), MONITOR
SWITCH AND MONITOR RESISTOR FOR
PROPER OPERATION. (REFER TO CHAPTER “TEST PROCEDURE”).
Latch Hook
2nd. Interlock
Relay Control
Switch
Door
FUSE M10A 250V
Monitor Switch
1. If the wire harness or electrical components are shortcircuited, this fuse blows to prevent an electric shock or
fire hazard.
2. This fuse blows when the 1st. latch switch and 2nd.
interlock relay (RY2) remain closed with the oven door
open and when the contacts (COM-NC) of monitor
switch closes.
3. The fuse also blows when asymmetric rectifier, H.V.
rectifier, H.V. wire harness, H.V. capacitor, magnetron or
secondary winding of high voltage transformer is shorted.
1st. Latch Switch
Switch Lever
Figure D-1. Door Open Mechanism
1ST. LATCH SWITCH AND 2ND. INTERLOCK
RELAY CONTROL SWITCH
1. When the oven door is closed, the contacts (COM-NO)
of each switch must be closed.
2. When the oven door is opened, the contacts (COMNO) of each switch must be opened.
FUSE 15A
If the wire harness or electrical components are shortcircuited, this fuse blows to prevent an electric shock or fire
hazard.
MONITOR SWITCH
1. When the door is closed, the contacts (COM-NC) must
8
R-880B
ASYMMETRIC RECTIFIER
FAN MOTOR
The asymmetric rectifier is a solid state device that prevents current flow in both directions. And it prevents the
temperature rise of the high voltage transformer by blowing
the fuse M10A when the high voltage rectifier is shorted.
The fan motor drives a blade which draws external cool air.
This cool air is directed through the air vanes surrounding
the magnetron and cools the magnetron. This air is channelled through the oven cavity to remove steam and
vapours given off from heating food. It is then exhausted
through the exhausting air vents of the oven cavity.
D2
ASYMMETRIC
RECTIFIER
D1
CONVECTION MOTOR
HIGH VOLTAGE
RECTIFIER
The convection motor drives the convection fan and
provides the heated air.
The rated peak reverse voltage of D1 of the asymmetric
rectifier is 6 KV. The rated peak reverse voltage of D2 of
the asymmetric rectifier is 1.7 KV. D1 and D2 of the
asymmetric rectifier or high voltage rectifier are shorted
when the each peak reverse voltage goes beyond the
each rated peak reverse voltage. (The process of blowing
the fuse M10A.)
1. The high voltage rectifier is shorted by any cause when
microwave cooking.
2. The peak reverse voltage of D2 of the rectifier goes
beyond the rated peak reverse voltage 1.7 KV in the
voltage doubler circuit.
3. D2 of the rectifier is shorted.
4. The large electric currents flow through the high voltage winding of the high voltage transformer.
5. The large electric currents beyond 10A flow through
the primary winding of the high voltage transformer.
6. The fuse blows by the large electric currents.
7. The power supply to the high voltage transformer is cut
off.
NOISE FILTER
The noise filter assembly prevents radio frequency interference that might flow back in the power circuit.
TOP HEATERS
The top heaters are located on the top of the oven cavity
assembly. The top heaters send out heat to grill foods.
BOTTOM HEATER
The bottom heater is located on the floor of the oven cavity
assembly. The bottom heater sends out heat to grill foods.
ONVECTION COOKING SYSTEM
This oven is designed with a hot air heating system where
food is not directly heated by the top and bottom heaters,
but is heated by forced circulation of the hot air produced
by the top and bottom heaters. The air heated by the top
and bottom heaters is circulated through the convection
passage provided on the outer casing of the oven cavity by
means of the convection fan which is driven by the
convection motor. It then enters the inside of the oven
through the vent holes provided on the left side of the oven.
Next, the hot air heats the food on the turntable and leaves
the oven cavity through the vent in the oven cavity left side
wall. Without leaving the oven, this hot air is reheated by
the top and bottom heaters, passes through the convection passage and enters the inside of the oven cavity
again, in a continuing cycle. In this way, the hot air
circulates inside the oven cavity to raise its temperature
and, at the same time, comes into contact with the food
being cooked. When the temperature inside the oven
cavity reaches the selected temperature, the top and
bottom heaters are de-energized. When the temperature
inside the oven cavity drops below the selected temperature, the top and bottom heaters are energized again. In
this way, the ins ide of the oven cavity is maintained at
approximately the selected temperature. When the convection time reaches 0, the top and bottom heaters are deenergized and the convection fan stops operating and the
oven shuts off. Upon completion of the cooking time, the
audible signal will sound, and oven lamp, turntable motor,
cooling fan motor and convection motor are de-energized.
At the end of the convection cycle, if the cavity air temperature is above 120˚C, the circuit to RY5 will be maintained
(by the thermistor circuit) to continue operation of the
cooling fan motor until the temperature drops below 104˚C,
at which time the relay will be de-energized, turning off the
fan motor. Relay RY1 will however, open as soon as the
convection cycle has ended, turning off the convection fan
motor. This will now cool.
THERMAL CUT-OUT 125˚C (MG)
This thermal cut-out protects the magnetron against overheating. If the temperature goes up higher than 125˚C
because the fan motor is interrupted or the ventilation
openings are blocked, the thermal cut-out will open and
line voltages to the high voltage transformer will be cut off
and the operation of the magnetron will be stopped.
THERMAL CUT-OUT170˚C (OVEN)
The thermal cut-out located on the top of the oven cavity
is designed to prevent damage to the oven if the foods in
the oven catch fire due to over heating produced by
improper setting of the cooking time or failure of control
unit. Under the normal operation, the oven thermal cut-out
remains closed. However, when abnormally high temperature are reached within the oven cavity, oven thermal
cut-out will open at 170˚C causing the oven to shut down.
The thermal cut-out will cut back in at 155˚C.
THERMISTOR
The thermistor is a negative temperature coefficient type.
The temperature in the oven cavity is detected through the
resistance of the thermistor, and then the control unit
causes the heating element relay to operate, thus the
current to the heating element is turned ON/OFF.
MONITOR RESISTOR
The monitor resistor prevents the fuse M10A bursting
when the fuse M10A blows due to the operation of the
monitor switch.
TURNTABLE MOTOR
The turntable motor drives the turntable roller assembly to
rotate the turntable.
9
R-880B
SERVICING
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current. Contact with following parts will
result in electrocution.
High voltage capacitor, High voltage transformer, Magnetron, High voltage rectifier assembly, High voltage harness.
REMEMBER TO CHECK 3D
REMEMBER TO CHECK 4R
1) Disconnect the supply.
2) Door opened, and wedged open.
3) Discharge high voltage capacitor.
1) Reconnect all leads removed from components during testing.
2) Replace the outer case (cabinet).
3) Reconnect the supply.
4) Run the oven. Check all functions.
WARNING: AGAINST THE CHARGE OF THE
HIGH-VOLTAGE CAPACITOR.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a
cup of cold water on the oven turntable, close the door
and set the power level to HIGH (100%) and set the
microwave timer for two (2) minutes. And push the start
key. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out 3D checks and re-examine the
connections to the component being tested.
The high-voltage capacitor remains charged about
60 seconds after the oven has been switched off.
Wait for 60 seconds and then short-circuit the connection of the high-voltage capacitor (that is, of the
connecting lead of the high-voltage rectifier) against
the chassis with the use of an insulated screwdriver.
Sharp recommend that wherever possible fault-finding is
carried out with the supply disconnected. It may in, some
cases, be necessary to connect the supply after the outer
case has been removed, in this event carry out 3D
checks and then disconnect the leads to the primary of
the high voltage transformer. Ensure that these leads
remain isolated from other components and the oven
chassis. (Use insulation tape if necessary.) When the
testing is completed carry out 3D checks and reconnect
the leads to the primary of the high voltage transformer.
When all service work is completed and the oven is fully assembled, the microwave power output should be checked
and microwave leakage test should be carried out.
TROUBLESHOOTING GUIDE
IMPORTANT: If the oven becomes inoperative because
of a blown fuse M10A in the 1st. latch
switch - 2nd. interlock relay(RY2)- monitor
switch - monitor resistor circuit, check the
1st. latch switch, 2nd. interlock relay(RY2),
monitor switch and monitor resistor before replacing the fuse M10A.
When troubleshooting the microwave oven, it is helpful to
follow the Sequence of Operation in performing the checks.
Many of the possible causes of trouble will require that a
specific test be performed. These tests are given a procedure letter which will be found in the “Test Procedure”
section.
10
11
AH. SENSOR
CONVECTION
COOKING
CONDITION
MIX
COOKING
CONDITION
GRILL
COOKING
CONDITION
MICROWAVE
COOKING
CONDITION
COOKING
CONDITION
(COMMON MODE)
OFF
CONDITION
CONDITION
Oven is in sensor cooking condition but AH sensor does not end 1st.
stage or does not stop cooking cycle or the oven stops soon.
Oven stops after 4 minutes 15 sec..
Convection motor does not operate.
Temperature is lower or higher than preset.
Bottom heater does not operate.
Top heaters do not operate.
Oven seems to be operating but little or no heat is produced in oven load.
(Microwave power does not seem to be generated properly.)
Bottom heater does not operate.
Top heaters do not operate.
Oven does not operating properly during variable cooking condition
except 100% cooking condition.
Oven seems to be operating but little or no heat is produced in oven load.
Oven goes into cook cycle but shuts down before end of cooking cycle.
Oven or electrical parts does not stop when cooking time is 0 or
STOP/CLEAR pad is pressed.
Turntable motor does not operate. (Oven lamp lights.)
Fan motor does not operate. (Oven lamp lights.)
Oven lamp does not light. (Turntable motor operates.)
Oven does not start when the INSTANT COOK/ START pad is pressed.
(Display operates.)
Display does not operate properly when STOP/CLEAR pad is pressed.
"SHARP MICRO- OVEN" does not appear in display when power cord is
plugged into wall outlet.
Home fuse blows when power cord is plugged into wall outlet.
Fuse M10A blows when the door is opened.
Fuse 15A blows when power cord is plugged into wall outlet.
PROBLEM
POSSIBLE CASE
AND
DEFECTIVE PARTS
E
MONITOR SWITCH
A B C D E E
RELAY RY2
RELAY RY1
KEY UNIT
TOUCH CONTROL PANEL
THERMISTOR
BOTTOM HEATER
TOP HEATERS
CONVECTION MOTOR
TURNTABLE MOTOR
NOISE FILTER
FUSE 15A
FUSE M10A
THERMAL CUT-OUT 170˚C
THERMAL CUT-OUT 125˚C
2ND. INTERLOCK RELAY
CONTROL SWITCH
1ST. LATCH SWITCH
HIGH VOLTAGE CAPACITOR
H.V. RECTIFIER ASSEMBLY
HIGH VOLTAGE TRANSFORMER
MAGNETRON
K K L M N O O O O O O P Q
RELAY RY3
F F G H I J J J
R-880B
MIS-ADJUSTMENT OF SWITCHES
OPENED WIRE HARNESS
SHORTED WIRE HARNESS
OVEN LAMP
POWER SUPPLY CORD
AH SENSOR
FOIL PATTERN ON P.W.B.
RELAY RY6
RELAY RY5
RELAY RY4
FAN MOTOR
R-880B
TEST PROCEDURES
PROCEDURE
LETTER
A
MAGNETRON TEST
COMPONENT TEST
NEVER TOUCH ANY PART IN THE CIRCUIT WITH YOUR HAND OR AN INSULATED TOOL
WHILE THE OVEN IS IN OPERATION.
CARRY OUT 3D CHECKS.
Isolate the magnetron from high voltage circuit by removing all leads connected to filament terminal.
To test for an open circuit filament use an ohmmeter to make a continuity test between the magnetron
filament terminals, the meter should show a reading of less than 1 ohm.
To test for short filament to anode condition, connect ohmmeter between one of the filament terminals
and the case of the magnetron (ground). This test should be indicated an infinite resistance. If a low
or zero resistance reading is obtained then the magnetron should be replaced.
MICROWAVE OUTPUT POWER (1 litre load)
The following test procedure should be carried out with the microwave oven in a fully assembled
condition (outer case fitted). Microwave output power from the magnetron can be measured by way
of IEC 705, i.e. it is measured by how much power the water load can absorb. To measure the
microwave output power in the microwave oven, the relation of calorie and watt is used. When P(W)
heating works for t(second), approximately P x t/4.187 calorie is generated. On the other hand, if the
temperature of the water with V(ml) rises ∆T (°C) during this microwave heating period, the calorie of
the water is V x ∆T.
The formula is as follows;
P x t / 4.187 = V x ∆ T
P (W) = 4.187 x V x ∆T / t
Our condition for water load is as follows:
Room temperature ........... around 20°C
Power supply Voltage .............. Rated voltage
Water load.................................. 1000 g
Initial temperature .............................. 10±2°C
Heating time .............................. 47 sec.
P = 90 x ∆T
Measuring condition:
1. Container
The water container must be a cylindrical borosilicate glass vessel having a maximum material
thickness of 3 mm and an outside diameter of approximately 190 mm.
2. Temperature of the oven and vessel
The oven and the empty vessel are at ambient temperature prior to the start the test.
3. Temperature of the water
The initial temperature of the water is (10±2)°C.
4. Select the initial and final water temperature so that the maximum difference between the final water
temperature and the ambient temperature is 5K.
5. Select stirring devices and measuring instruments in order to minimize addition or removal of heat.
6. The graduation of the thermometer must be scaled by 0.1°C at minimum and be an accurate
thermometer.
7. The water load must be (1000±5) g.
8. “t” is measured while the microwave generator is operating at full power. Magnetron filament heatup time is not included.
NOTE: The operation time of the microwave oven is “t + 2” sec. (2 sec. is magnetron filament heat-up time.)
Measuring method:
1. Measure the initial temperature of the water before the water is added to the vessel.
(Example: The initial temperature T1 = 11°C)
2. Add the 1 litre water to the vessel.
3. Place the load on the centre of the shelf.
4. Operate the microwave oven at HIGH for the temperature of the water rises by a value ∆ T of
(10 ± 2) K.
5. Stir the water to equalize temperature throughout the vessel.
6. Measure the final water temperature. (Example: The final temperature T2 = 21°C)
7. Calculate the microwave power output P in watts from above formula.
12
R-880B
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
Initial temperature .................................................................................................. T1 = 11°C
Temperature after (47 + 2) = 49 sec ...................................................................... T2 = 21°C
Temperature difference Cold-Warm ....................................................................... ∆T1 = 10C
Measured output power
The equation is “P = 90 x ∆T” ...................................................... P = 90 x 10°C = 900 Watts
JUDGMENT: The measured output power should be at least ± 15 % of the rated output power.
CAUTION: 1°C CORRESPONDS TO 90 WATTS. REPEAT MEASUREMENT IF THE POWER IS
INSUFFICIENT.
1000g
1000g
1000g
T1˚C
T2˚C
Heat up for 49 sec
B
HIGH VOLTAGE TRANSFORMER TEST
WARNING:
High voltage and large currents are present at the secondary winding and
filament winding of the high voltage transformer. It is very dangerous to work
near this part when the oven is on. NEVER make any voltage measurements
of the high-voltage circuits, including the magnetron filament.
CARRY OUT 3D CHECKS.
Disconnect the leads to the primary winding of the high voltage transformer. Disconnect the filament
and secondary winding connections from the rest of the HV circuitry. Using an ohmmeter, set on a low
range, it is possible to check the continuity of all three windings. The following readings should be
obtained:a. Primary winding ................................ approximately 1.5 Ω
b. Secondary winding .......................... approximately 117 Ω
c. Filament winding......................................... less than 1 Ω
If the readings obtained are not stated as above, then the high voltage transformer is probably faulty
and should be replaced.
CARRY OUT 4R CHECKS.
C
HIGH VOLTAGE RECTIFIER ASSEMBLY TEST
HIGH VOLTAGE RECTIFIER TEST
CARRY OUT 3D CHECKS.
Isolate the high voltage rectifier assembly from the HV circuit. The high voltage rectifier can be tested
using an ohmmeter set to its highest range. Connect the ohmmeter across the terminal B+C of the high
voltage rectifier and note the reading obtained. Reverse the meter leads and note this second reading.
The normal resistance is infinite in one direction and more than 100 kΩ in the other direction.
CARRY OUT 4R CHECKS.
A D2
B
D1
ASYMMETRIC RECTIFIER TEST
ASYMMETRIC
RECTIFIER
CARRY OUT 3D CHECKS.
C
HIGH VOLTAGE RECTIFIER
Isolate the high voltage rectifier assembly from the HV circuit. The asymmetric can be tested using an
ohmmeter set to its highest range across the terminals A+B of the asymmetric rectifier and note the
reading obtained. Reverse the meter leads and note this second reading. If an open circuit is indicated
in both direction then the asymmetric rectifier is good. If an asymmetric rectifier is shorted in either
direction, then the asymmetric rectifier is probably faulty and must be replaced with high voltage
rectifier. When the asymmetric rectifier is defective, check whether magnetron, high voltage rectifier,
high voltage wire or filament winding of the high voltage transformer is shorted.
CARRY OUT 4R CHECKS.
13
R-880B
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
NOTE: FOR MEASUREMENT OF THE RESISTANCE OF THE RECTIFIER, THE BATTERIES OF
THE MEASURING INSTRUMENT MUST HAVE A VOLTAGE AT LEAST 6 VOLTS, BECAUSE OTHERWISE AN INFINITE RESISTANCE MIGHT BE SHOWN IN BOTH DIRECTIONS.
D
HIGH VOLTAGE CAPACITOR TEST
CARRY OUT 3D CHECKS.
A. Isolate the high voltage capacitor from the circuit.
B. Continuity check must be carried out with measuring instrument which is set to the highest
resistance range.
C. A normal capacitor shows continuity for a short time (kick) and then a resistance of about 10MΩ after
it has been charged.
D. A short-circuited capacitor shows continuity all the time.
E. An open capacitor constantly shows a resistance about 10 MΩ because of its internal 10MΩ
resistance.
F. When the internal wire is opened in the high voltage capacitor shows an infinite resistance.
G. The resistance across all the terminals and the chassis must be infinite when the capacitor is
normal.
If incorrect reading are obtained, the high voltage capacitor must be replaced.
CARRY OUT 4R CHECKS.
E
SWITCH TEST
CARRY OUT 3D CHECKS.
Isolate the switch to be tested and using an ohmmeter check between the terminals as described in
the following table.
Table: Terminal Connection of Switch
Plunger Operation
COM to NO
COM to NC
Released
Depressed
Open circuit
Short circuit
Short circuit
Open circuit
COM; Common terminal,
NO; Normally open terminal
NC; Normally close terminal
If incorrect readings are obtained, make the necessary switch adjustment or replace the switch.
CARRY OUT 4R CHECKS.
F
THERMAL CUT-OUT TEST
CARRY OUT 3D CHECKS.
Disconnect the leads from the terminals of the thermal cut-out. Then using an ohmmeter, make a continuity
test across the two terminals as described in the below.
Table: Thermal Cut-out Test
Parts Name
Temperature of "ON"
condition (closed circuit).
(˚C)
Temperature of "OFF"
condition (open circuit).
(˚C)
Indication of ohmmeter
(When room temperature
is approx. 20˚C.)
Thermal cut-out 125˚C
This is not resetable type.
Above 125˚C
Closed circuit
Thermal cut-out 170˚C
Cuts back in at 155˚C.
Above 170˚C
Closed circuit
If incorrect readings are obtained, replace the thermal cut-out.
An open circuit thermal cut-out (MG) indicates that the magnetron has overheated, this may be due
to resistricted ventilation, cooling fan failure or a fault condition within the magnetron or HV. circuit.
An open circuit thermal cut-out (OVEN) indicates that the food in the oven cavity may catch fire, this
may be due to over heating produced by improper setting of the cooking timer or failure of the control
panel.
CARRY OUT 4R CHECKS.
14
R-880B
TEST PROCEDURES
PROCEDURE
LETTER
G
BLOWN FUSE M10A
COMPONENT TEST
CARRY OUT 3D CHECKS.
If the fuse M10A is blown when the door is opened, check the 1st. latch switch, 2nd. interlock relay,
monitor switch and monitor resistor.
If the fuse M10A is blown, there could be a short or ground in electrical parts or wire harness. Check
them and replace the defective parts or repair the wire harness.
If the fuse M10A is blown, there could be a short in the asymmetric rectifier or there is a ground in wire
harness. A short in the asymmetric rectifier may be occurred due to short or ground in H.V. rectifier,
magnetron, high voltage transformer or H.V. wire. Check them and replace the defective parts or repair
the wire harness.
CARRY OUT 4R CHECKS.
CAUTION:
H
Only replace fuse M10A with the correct value replacement.
BLOWN FUSE 15A
CARRY OUT 3D CHECKS.
If the fuse 15A is blown, there could be a short or ground in electrical parts or wire harness. Check them
and replace the defective parts or repair the wire harness.
CARRY OUT 4R CHECKS.
CAUTION:
I
Only replace fuse 15A with the correct value replacement.
NOISE FILTER TEST
N
WHT
L
RED
CARRY OUT 3D CHECKS.
Disconnect the leads from the terminals of noise filter.
Using an ohmmeter, check between the terminals as
described in the following table.
MEASURING POINTS
Between N and L
Between terminal N and WHITE
Between terminal L and RED
F8A
INDICATION OF OHMMETER
Approx. 680 kΩ
Short circuit
Short circuit
If incorrect readings are absorbed, replace the noise filter unit.
CARRY OUT 4R CHECKS.
J
MOTOR WINDING TEST
CARRY OUT 3D CHECKS.
Disconnect the leads from the motor. Using an ohmmeter, check the resistance between the two
terminals as described in the table below.
Table: Resistance of Motor
Motors
Resistance
Fan motor
Approximately 290 Ω
Turntable motor
Approximately 14 kΩ
Convection motor
Approximately 293 Ω
If incorrect readings are obtained, replace the motor.
CARRY OUT 4R CHECKS.
K
TOP HEATERS AND BOTTOM HEATER TEST
CARRY OUT 3D CHECKS.
Before carrying out the following tests make sure the heater is cool completely.
1. Resistance of heater.
Disconnect the wire leads to the heater to be tested. Using ohmmeter with low resistance range.
15
R-880B
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
Check the resistance across the terminals of the heater as described in the following table.
Table: Resistance of heater
Parts name
Resistance
Top heaters
Approximately 20 Ω x 2 = 40 Ω
Bottom heater
Approximately 61 Ω
2. Insulation resistance.
Disconnect the wire leads to the heater to be tested. Check the insulation resistance between the
heater terminal and cavity using a 500V - 100MΩ insulation tester. The insulation resistance should
be more than 10 MΩ in the cold start.
If the results of above test 1 and/or 2 are out of above specifications, the heater is probably faulty and
should be replaced.
CARRY OUT 4R CHECKS.
L
THERMISTOR TEST
1. CARRY OUT 3D CHECKS.
2. Disconnect connector-D from the control unit. Measure the resistance of the thermistor with an
ohmmeter. Connect the ohmmeter leads to Pin No’s D1 and D3.
Room Temperature
68˚F(20˚C) - 86˚F(30˚C)
Resistance
Approx. 293kΩ - 184KΩ
3. If the meter does not indicate above resistance, replace the thermistor
4. CARRY OUT 4R CHECKS.
M
CONTROL PANEL ASSEMBLY TEST
The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore,
unlike conventional microwave ovens, proper maintenance can not be performed with only a voltmeter
and ohmmeter.
In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key
Unit, and also the Control unit is divided into two units, CPU unit and Power unit, and troubleshooting
by replacement is described according to the symptoms indicated.
1. Key Unit Note : Check key unit ribbon connection before replacement.
The following symptoms indicate a defective key unit. Replace the key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
2. Control Panel
The following symptoms indicate a defective control unit. Before replacing the control unit.
perform the key unit test (Procedure N) to determine if control unit is faulty.
2-1 In connection with pads
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light up.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) The figure of all digits flicker.
2-3 Other possible troubles caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
d) Proper temperature measurement is not obtained.
16
R-880B
TEST PROCEDURES
PROCEDURE
LETTER
N
KEY UNIT TEST
COMPONENT TEST
If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable
is marking good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing switch
(stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and
make sure the door sensing switch is closed (either close the door or short the door sensing switch
connecter). Use the Key unit matrix indicated on the control panel schematic and place a jumper wire
between the pins that correspond to the STOP/CLEAR pad marking momentary contact. If the control
unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does
not respond, it is a faulty and must be replaced. If a specific pad does not respond, the above method
may be used (after clearing the control unit) to determine if the control unit or key pad is at fault.
G12 G11 G10
G9
G8
5
160˚C
G7
G6
G5
G4
G3
G2
G1
4
3
2
1
130˚C
70˚C
40˚C
EASY
DEFROST
MULTI
COOK
HELP
150˚C
0
9
250˚C
230˚C
8
7
6
220˚C
200˚C
180˚C
INSTANT
COOK
START MORE
Pasta
POWER
LEVEL
Jacket
Potato
CONVEC CLOCK
PREHEAT
GRILL
Reheat
Pie
REHEAT
STOP
Fresh
SENSOR Vegetables CLEAR
Rice
Frozen CONVENIENCE
Vegetables
/PIZZA
LESS
MIX
CARRY OUT 4R CHECKS.
O
RELAY TEST
CARRY OUT 3D CHECKS.
Remove the outer case and check voltage between Pin No. 1 of the 3 pin connector (A) and the
common terminal of the relay RY6 on the control unit with an A.C. voltmeter.
The meter should indicate 220 volts, if not check oven circuit.
Relay Test
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation, grill
operation, convection operation or mix operation.
DC. voltage indicated .......... Defective relay.
DC. voltage not indicated .... Check diode which is connected to the relay coil. If diode is good,
control unit is defective.
RELAY SYMBOL
OPERATIONAL VOLTAGE
CONNECTED COMPONENTS
RY1
RY2
RY3
Approx. 24.0V D.C.
Approx. 24.0V D.C.
Approx. 24.0V D.C.
Convection motor
High voltage transformer
Grill heaters (Top)
RY4
RY5
RY6
Approx. 24.0V D.C.
Approx. 24.0V D.C.
Approx. 24.0V D.C.
Bottom heater
Fan motor
Oven lamp / Turntable motor
CARRY OUT 4R CHECKS.
P
PROCEDURES TO BE TAKEN WHEN THE FOIL PATTERN ON THE PRINTED WIRING BOARD
(PWB) IS OPEN
To protect the electronic circuits, this model is provided with a fine foil pattern added to the input circuit
on the PWB, this foil pattern acts as a fuse. If the foil pattern is open, follow the troubleshooting guide
given below for repair.
Problem: POWER ON, indicator does not light up.
CARRY OUT 3D CHECKS.
17
R-880B
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
STEPS
OCCURRENCE
1
The rated AC voltage is not present at
Power terminal of CPU connector (CN-A).
Check supply voltage and oven power cord.
CAUSE OR CORRECTION
2
The rated AC voltage is present at primary
side of low voltage transformer.
Low voltage transformer or secondary circuit defective.
Check and repair.
3
Only pattern at "a" is broken.
*Insert jumper wire J1 and solder.
(CARRY OUT 3D CHECKS BEFORE REPAIR.)
4
Pattern at "a" and "b" are broken.
*Insert the coil RCILF2003YAZZ between "c" and "d".
(CARRY OUT 3D CHECKS BEFORE REPAIR.)
c
VRS1
a
5
(J1)
NOTE: *At the time of these repairs, make a
visual inspection of the varistor for
burning damage and examine the
transformer with tester for the presence of layer short circuit (check primary coil resistance).
If any abnormal condition is detected,
replace the defective parts.
FAN
b
d
1
AC
CARRY OUT 4R CHECKS.
CN - A
Q
AH SENSOR TEST
Checking the initial sensor cooking condition
(1) The oven should be plugged in at least two minutes before sensor cooking.
(2) Room temperature should not exceed 35˚C.
(3) The unit should not be installed in any area where heat and steam are generated. The unit should
not be installed, for example, next to a conventional surface unit. Refer to the "INSTALLATION
Instructions" .
(4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To
permit adequate ventilation, be sure to install so as not to block these vents. There should be some
space for air circulation.
(5) Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any
moisture with a dry cloth or paper towel.
(6) The Sensor works with food at normal storage temperature. For example, chicken pieces would
be at refrigerator temperature and canned soup at room temperature.
(7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The
sensor will detect the vapor given of by the spray and turn off before food is properly cooked.
(8) After the oven is started on sensor cooking condition, if the sensor has not detected the vapor of
the food, ERROR will appear and the oven will shut off.
Water load cooking test
Make sure the oven has been plugged in at least five minutes before checking sensor cook operation.
The cabinet should be installed and screws tightened.
(1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
(2) Place the container on the center of tray in the oven cavity.
(3) Close the door.
(4) Touch Fresh vegetables pad. Now, the oven is in the sensor cooking condition and "FRESH",
"VEGETABLES", "SENSOR" and "COOKING" will appear in the display.
(5) The oven will operate for the first 16 seconds, without generating microwave energy.
When the AH sensor is defective (open or short), ERROR will appear in the display immediately.
If ERROR appears check sensor wire connections and/or AH sensor.
NOTE: ERROR will appear if the door is opened or STOP/CLEAR pad is touched during first stage of
sensor cooking.
(6) After approximately 16 seconds, microwave energy is produced, and the display should start to
count down the remaining cooking time and oven should turn off after water is boiling (bubbling).
If the oven does not turn off, replace the AH sensor or check the control unit, refer to explanation
below.
18
R-880B
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement
sensor.
(1) Disconnect oven from power supply and then remove outer case.
(2) Discharge the high voltage capacitor.
(3) Remove the AH sensor.
(4) Install the new AH sensor.
(5) Re-install the outer case.
(6) Reconnect the oven to the power supply and check the sensor cook operation, proceed as follows:
6-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
6-2. Place the container on the center of tray in the oven cavity.
6-3. Close the door.
6-4. Touch Fresh Vegetables pad.
6-5. The control panel is in automatic Sensor operation.
6-6. The display will start to count down the remaining cooking time, and the oven will turn off
automatically after the water is boiling (babbling).
If new sensor dose not operate properly, the problem is with the control unit.
CHECKING CONTROL UNIT
(1) Disconnect oven from power supply and then remove outer case.
(2) Discharge the high voltage capacitor.
(3) Disconnect the wire leads from the cook relay.
(4) Disconnect the sensor connector that is mounted to lower portion of control panel.
(5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel.
(6) Reconnect the oven to the power supply and check the sensor cook operation, proceed as follows:
6-1. Touch Fresh Vegetables pad.
6-2. The control panel is in the sensor cooking operation.
6-3. After approximately 1 minute and 15 seconds, push plunger of select switch. This condition
is same as judgement by AH sensor.
6-4. After approximately 3 seconds, the oven stops.
If the above is not the case, the control unit is probably defective.
If the above is proper, the AH sensor is probably defective.
Plunger
NC
NO
F-1
F-2
To connector (F)
on Control Unit.
1
2
3
COM
COM NO
R1
F-3
R2
CONNECTOR
R3
R4
R1,R2 : 22Ω ± 1% 1/2W
R3 : 4.3kΩ ± 5% 1/4W
R4 : 1MΩ ± 5% 1/4W
Sensor Dummy Resistor Circuit
19
NC
R-880B
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
The touch control section consists of the following units as
shown in the touch control panel circuit.
4) ACL
A circuit to generate a signal which resets the LSI to the
initial state when power is supplied.
(1) Key Unit
(2) Control Unit (The Control unit consists of Power unit
and CPU unit.)
5) Buzzer Circuit
The buzzer is responsive to signals from the LSI to emit
audible sounds (key touch sound and completion
sound).
The principal functions of these units and signals communicated among them are explained below.
Key Unit
The key unit is composed of a matrix, signals generated in
the LSI are sent to the key unit from P40, P41, P72, P73
P74, P75, P76 and P77.
When a key pad is touched, a signal is completed through
the key unit and passed back to the LSI through P44 - P47
to perform the function that was requested.
6) Door Sensing Switch (Stop Switch)
A switch to "tell" the LSI if the door is open or closed.
Control Unit
Control unit consists of LSI, power source circuit, synchronizing signal circuit, ACL circuit, buzzer circuit, relay
circuit, temperature measurement circuit, indicator circuit,
absolute humidity sensor circuit and back light circuit.
8) Back Light Circuit
A circuit to drive the back light (Light emitting diodes
LD1 - LD10).
7) Relay Circuit
To drive the magnetron, grill heaters, bottom heater,
convection motor, fan motor, turntable motor, convection motor and light the oven lamp.
9) Indicator Circuit
This circuit consists of 2 line, 7-digits, 45-segments
and 5-common electrodes using a Liquid Crystal Display.
1) LSI
This LSI controls the temperature measurement signal, AH sensor signal, key strobe signal, relay driving
signal for oven function and indicator signal.
10) Temperature Measurement Circuit : (OVEN THERMISTOR)
The temperature in the oven cavity is sensed by the
thermistor. The variation of resistance according to
sensed temperature is detected by the temperature
measurement circuit and the result applied to LSI. The
LSI uses this information to control the relay and
display units.
2) Power Source Circuit
This circuit generates voltage necessary in the control
unit.
Symbol
VC
Voltage
-5.2V
Application
LSI(IC1)
3) Synchronizing Signal Circuit
The power source synchronizing signal is available in
order to compose a basic standard time in the clock
circuit. It accompanies a very small error because it
works on commercial frequency.
11) Absolute Humidity Sensor Circuit
This circuit detects the humidity of a food which is
being cooked, to control its automatic cooking.
DESCRIPTION OF LSI
LSI(IZA927DR)
The I/O signal of the LSI(IZA927DR) are detailed in the following table.
Pin No.
1
2
3-5
6
7
Signal
C1
VL1
I/O
IN
IN
Description
Terminal not used.
Power source voltage input terminal.
Standard voltage for LCD.
AN7-AN5
AN4
IN
IN
Heating constant compensation terminal.
Terminal not used.
AN3
IN
Temperature measurement input: OVEN THERMISTOR.
By inputting DC voltage corresponding to the temperature detected by the
thermistor, this input is converted into temperature by the A/D converter built into
the LSI.
20
R-880B
Pin No.
8
Signal
AN2
I/O
IN
Description
Input signal which communicates the door open/close information to LSI.
Door closed; "H" level signal.
Door opened; "L" level signal.
AH sensor input.
This input is an analog input terminal from the AH sensor circuit, and connected
to the A/D converter built into the LSI.
9
AN1
IN
10
AN0
IN
11
P57
OUT
12
P56
OUT
13
P55
OUT
P54-P50
P47
OUT
IN
20
P46
IN
21
P45
IN
22
P44
IN
23
24
INT1
INT0
IN
IN
14-18
19
Used for initial balancing of the bridge circuit (absolute humidity sensor). This
input is an analog input terminal from the AH sensor circuit, and connected to
the A/D converter built into LSI.
This input is an analog input terminal from the AH sensor circuit, and connected
to the A/D converter built into the LSI.
Timing signal output terminal for temperature measurement(OVEN
THERMISTOR).
"H" level (GND) : Thermistor OPEN timing.
"L" level (-5V) : Temperature measuring timing. (Convection cooking)
Signal to sound buzzer.
0.12 sec
A: key touch sound.
A
B: Completion sound.
2.4 sec
C: When the temperature of the oven
B
cavity reaches the preset
1.2 sec
1.2 sec
temperature in the preheating mode,
H: GND
C
or when the preheating hold time (30
L
minutes) is elapsed.
Timing signal output terminal for temperature measurement(OVEN
THERMISTOR).
"H" level (GND) : Thermistor OPEN timing.
"L" level (-5V) : Temperature measuring timing. (Convection cooking)
Used for initial balancing of the bridge circuit (absolute humidity sensor).
Signal coming from touch key.
When any one of G12 line keys on key matrix is touched, a corresponding signal
from P40, P41, P72, P73, P74, P75, P76 and P77 will be input into P47. When no
key is touched, the signal is held at "L" level.
Signal similar to P47.
When any one of G11 line keys on key matrix is touched, a corresponding signal
will be input into P46.
Signal similar to P47.
When any one of G10 line keys on key matrix is touched, a corresponding signal
will be input into P45.
Signal similar to P47.
When any one of G9 line keys on key matrix is touched, a corresponding signal will
be input into P44.
Terminal not used.
Signal to synchronized LSI with commercial power source
frequency(50Hz).
This is basic timing for time processing of LSI.
H : GND
L (-5V)
20 msec.
25
P41
OUT
26
P40
OUT
27
P77
OUT
28
P76
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P44 - P47 terminal
while one of G8 line key on matrix is touched.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P44 - P47 terminal
while one of G7 line key on matrix is touched.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P44 - P47 terminal
while one of G6 line key on matrix is touched.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P44 - P47 terminal
while one of G5 line key on matrix is touched.
21
R-880B
Pin No.
Signal
I/O
Description
29
P75
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P44 - P47 terminal
while one of G4 line key on matrix is touched.
30
P74
OUT
31
P73
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P44 - P47 terminal
while one of G3 line key on matrix is touched.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P44 - P47 terminal
while one of G2 line key on matrix is touched.
32
P72
OUT
33
P71
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P44 - P47 terminal
while one of G1 line key on matrix is touched.
Oven lamp and turntable motor driving signal(Square Waveform : 50Hz).
To turn on and off shut-off relay
(RY6). The square waveform voltage
is delivered to the relay (RY6) driving
circuit.
20 msec.
H
L
During cooking
34
P70
IN
Connected to VC.
35
RESET
IN
36
P81
OUT
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily
set to "L" level the moment power is applied, at this time the LSI is reset. Thereafter
set at "H" level.
Magnetron high-voltage circuit driving signal.
To turn on and off the cook
relay (RY2). In 100%
operation, the signals hold "L"
level during microwave
cooking and "H" level while not
cooking. In other cooking
modes (70%, 50%, 30%,
10%) the signal turns to "H"
level and "L" level in repetition
according to the power level.
37
P80
OUT
38
XIN
IN
39
XOUT
OUT
40
VSS
IN
41
P27
OUT
ON/OFF time ratio in Micro cooking
(a. 32second time base)
ON/OFF time ratio in Micro cooking
(a. 48second time base)
MICRO
COOK
100%
70%
50%
30%
10%
MICRO
COOK
100%
70%
50%
30%
10%
ON
OFF
32 sec. 0 sec.
24 sec. 8 sec.
18 sec. 14 sec.
12 sec. 20 sec.
6 sec. 26 sec.
Grill heaters (TOP HEATER) driving signal.
To turn on and off the grill heaters
Power output
relay (RY3). "L" level during grill
100 %
90 %
(TOP GRILL, TOP AND
80 %
BOTTOM) cooking, Convection
70 %
cooking or Mix top grill cooking,
60 %
"H" level otherwise.
50 %
The heater relay turns on and off
40 %
30 %
within a 48 second time base in
20 %
accordance with the special
10 %
program in LSI.
ON time
48 sec.
44 sec.
40 sec.
36 sec.
32 sec.
26 sec.
22 sec.
16 sec.
12 sec.
8 sec.
ON
OFF
48 sec.
36 sec.
26 sec.
16 sec.
8 sec.
0 sec.
12 sec.
22 sec.
32 sec.
40 sec.
OFF time
0 sec.
4 sec.
8 sec.
12 sec.
16 sec.
22 sec.
26 sec.
32 sec.
36 sec.
40 sec.
Internal clock oscillation frequency input setting.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit
with respect to XIN terminal.
Internal clock oscillation frequency control output.
Output to control oscillation input of XOUT.
Power source voltage: -5V.
VC voltage of power source circuit input.
Bottom heater driving signal.
To turn on and off the bottom relay
(RY4). "L" level during grill (TOP AND
BOTTOM) cooking, Convection
cooking or Mix bottom cooking, "H"
level otherwise.
The heater relay turns on and off
within a 48 second time base in
accordance with the special program
in LSI.
22
Power output
100 %
90 %
80 %
70 %
60 %
50 %
40 %
30 %
20 %
10 %
ON time
48 sec.
44 sec.
40 sec.
36 sec.
32 sec.
26 sec.
22 sec.
16 sec.
12 sec.
8 sec.
OFF time
0 sec.
4 sec.
8 sec.
12 sec.
16 sec.
22 sec.
26 sec.
32 sec.
36 sec.
40 sec.
R-880B
Pin No.
42
43
Signal
P26
P25
I/O
OUT
OUT
Description
Convection motor driving signal.
To turn on and off shut-off relay(RY1).
"L" level during CONVECTION; "H" level
otherwise. (Relay RY1 does not turn on
at preheating mode.)
Fan motor driving signal.
To turn on and off the fan motor relay
RY5. "L" level during cooking, or for 5
minutes after grill cooking or Mix cooking
for a while after convection. "H" level
otherwise.
OFF
ON
44
P24
OUT
Terminal not used.
45
P23
OUT
46-48
P22-P20
OUT
Common data signal: COM5.
Connected to LCD (Pin No. 37)
Segment data signal.
Connected to LCD. No connection in LCD.
49-50
P17-P16
OUT
51-80
SEG39-SEG10
OUT
SEG9
OUT
Segment data signal.
Connected to LCD. No connection in LCD.
SEG8-SEG0
OUT
Segment data signal.
Connected to LCD. Signal is similar to SEG39.
91
VCC
IN
Connected to GND.
92
VREF
IN
Connected to GND.
93
94
AVSS
COM3
IN
OUT
Connected to VC.
Common data signal: COM4.
Connected to LCD (Pin No. 36).
95
COM2
OUT
96
COM1
OUT
Common data signal: COM3.
Connected to LCD (Pin No. 35).
Common data signal: COM2.
Connected to LCD (Pin No. 34).
97
COM0
OUT
81
82-90
ON
During
cooking
(Convection)
OFF
H. GND
L
H. GND
L
During cooking or for 5 minutes after
grill, mix or for awhile after convection.
Segment data signal.
Connected to LCD. No connection in LCD.
Segment data signal.
Connected to LCD.
The relation between signals are as follows:
LSI signal (Pin No.) LCD (Pin No.) LSI signal (Pin No.) LCD (Pin No.)
SEG 0 (90) ....................SEG45 (51) SEG23 (67) ................. SEG17 (17)
SEG 1 (89) ....................SEG44 (50) SEG24 (66) ................. SEG16 (16)
SEG 2 (88) ....................SEG43 (49) SEG25 (65) ................. SEG15 (15)
SEG 3 (87) ....................SEG42 (48) SEG25 (65) ................. SEG15 (32)
SEG 4 (86) ....................SEG41 (47) SEG26 (64) ................. SEG14 (14)
SEG 5 (85) ....................SEG40 (46) SEG27 (63) ................. SEG13 (13)
SEG 6 (84) ....................SEG39 (45) SEG28 (62) ................. SEG12 (12)
SEG 7 (83) ....................SEG38 (44) SEG29 (61) ................. SEG11 (11)
SEG 8 (82) ....................SEG37 (43) SEG30 (60) ................. SEG10 (10)
SEG 9 (81) ....................SEG31 (31) SEG31 (59) ................... SEG 9 ( 9)
SEG10 (80) ................... SEG30 (30) SEG32 (58) ................... SEG 8 ( 8)
SEG11 (79) ................... SEG29 (29) SEG33 (57) ................... SEG 7 ( 7)
SEG12 (78) ................... SEG28 (28) SEG34 (56) ................... SEG 6 ( 6)
SEG13 (77) ................... SEG27 (27) SEG35 (55) ................... SEG 5 ( 5)
SEG14 (76) ................... SEG26 (26) SEG36 (54) ................... SEG 4 ( 4)
SEG15 (75) ................... SEG25 (25) SEG37 (53) ................... SEG 3 ( 3)
SEG16 (74) ................... SEG24 (24) SEG38 (52) ................... SEG 2 ( 2)
SEG17 (73) ................... SEG23 (23) SEG39 (51) ................... SEG 1 ( 1)
SEG18 (72) ................... SEG22 (22) P16 (50) ...................... SEG32 (38)
SEG19 (71) ................... SEG21 (21) P17 (49) ...................... SEG33 (39)
SEG20 (70) ................... SEG20 (20) P20 (48) ...................... SEG34 (40)
SEG21 (69) ................... SEG19 (19) P21 (47) ...................... SEG35 (41)
SEG22 (68) ................... SEG18 (18) P22 (46) ...................... SEG36 (42)
Common data signal: COM1.
Connected to LCD (Pin No. 33).
23
R-880B
Pin No.
98-99
Signal
I/O
VL3-VL2
IN
C2
IN
100
Description
Power source voltage input terminal.
Standard voltage for LCD.
Terminal not used.
ABSOLUTE HUMIDITY SENSOR CIRCUIT
With this voltage given, the switches SW1 to SW5 in
the LSI are turned on in such a way as to change the
resistance values in parallel with R107 ~ R111 of IC2.
Changing the resistance values results in that there is
the same potential at both F-3 terminal of the absolute
humidity sensor and AN0 terminal of the LSI. The
voltage of AN1 terminal will indicate about -2.5V. This
initial balancing is set up about 16 seconds after the
unit is put in the Sensor Cooking mode. As the sensor
cooking proceeds, the food is heated to generate
moisture by which the resistance balance of the bridge
circuit is deviated to increase the voltage available at
AN1 terminal of the LSI.
Then the LSI observes that voltage at AN1 terminal and
compares it with its initial value, and when the comparison rate reaches the preset value (fixed for each menu
to be cooked), the LSI causes the unit to stop sensor
cooking; thereafter, the unit goes in the next operation
automatically.
When the LSI starts to detect the initial voltage at AN1
terminal 16 seconds after the unit has been put in the
Sensor Cooking mode, if it is not possible to balance,
of the bridge circuit due to disconnection of the absolute humidity sensor, ERROR will appear on the display and the cooking is stopped.
(1) Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed
in the closed vessel filled with dry air while another in
the open vessel. Each sensor is provided with the
protective cover made of metal mesh to be protected
from the external airflow.
Thermistors
Sensing part
Sensing part
(Closed vessel)
(Open vessel)
(2) Operational Principle of Absolute Humidity Sensor
The figure below shows the basic structure of an
absolute humidity sensor. A bridge circuit is formed by
two thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
Each thermistor is supplied with a current to keep it
heated at about 150˚C (302˚F), the resultant heat is
dissipated in the air and if the two thermistors are
placed in different humidity conditions they show different degrees of heat conductivity leading to a potential
difference between them causing an output voltage
from the bridge circuit, the intensity of which is increased as the absolute humidity of the air increases.
Since the output is very minute, it is amplified by the
operational amplifier.
C. Thermistor in
closed vessel
S. Thermistor in
open vessel
620k
14
R108
300k
15
R109
150k
16
R110
75k
17
R111
37.4k
18
R106
S
R105
3.32k R101
1.8k
+
IC2
R102
360k
VA : -15V
24
VA : -15V
P53
P52
P51
P50
47k
D101
VC : -5V
SW2
SW3
SW4
SW5
AN0
0.01uF
R103 R104
10k
R90
F-2
0.1
uF
C101
F-1
C
R112
F-3
3.57k
(3) Detector Circuit of Absolute Humidity Sensor Circuit
This detector circuit is used to detect the output voltage
of the absolute humidity circuit to allow the LSI to
control sensor cooking of the unit. When the unit is set
in the sensor cooking mode, 16 seconds clearing cycle
occurs than the detector circuit starts to function and
the LSI observes the initial voltage available at its AN1
terminal.
10
SW1
P54
LSI
(IC1)
C104
47k
Absolute humidity (g/m 2 )
0.01uF
S : Thermistor
open vessel
C : Thermistor
closed vessel
R107
0.015uF
R3
R2
Absolute humidity vs,
output voltage characterist
C103
S
R1
Operational
amplifier
Output
voltage
+
Output voltage
C
1) Absolute humidity sensor circuit
C102
ventilation opening for sensing
9
AN1
R-880B
SERVICING
1. Precautions for Handling Electronic Components
5) Re-connect the power supply cord after the outer case
is installed.
6) Run the oven and check all functions.
This unit uses CMOS LSI in the integral part of the circuits.
When handling these parts, the following precautions
should be strictly followed. CMOS LSI have extremely
high impedance at its input and output terminals. For this
reason, it is easily influenced by the surrounding high
voltage power source, static electricity charge in clothes,
etc., and sometimes it is not fully protected by the built-in
protection circuit.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them
in aluminium foil. Also wrap PW boards containing
them in aluminium foil.
2) When soldering, ground the technician as shown in
the figure and use grounded soldering iron and work
table.
A. On some models, the power supply cord between the
touch control panel and the oven itself is so short that
the two can't be separated.
For those models, check and repair all the controls
(sensor-related ones included) of the touch control
panel while keeping it connected to the oven.
B. On some models, the power supply cord between the
touch control panel and the oven proper is long enough
that they may be separated from each other. For those
models, therefore, it is possible to check and repair the
controls of the touch control panel while keeping it apart
from the oven proper; in this case you must short both
ends of the door sensing switch (on PWB) of the touch
control panel with a jumper, which brings about an
operational state that is equivalent to the oven door
being closed. As for the sensor-related controls of the
touch control panel, checking them is possible if the
dummy resistor(s) with resistance equal to that of the
controls are used.
approx. 1M ohm
2. Shapes of Electronic Components
(2) Servicing the touch control panel with power
supply from an external power source:
E
C
Disconnect the touch control panel completely from
the oven proper, and short both ends of the door
sensing switch (on PWB) of the touch control panel,
which brings about an operational state that is equivalent to the oven door being closed. Connect an external power source to the power input terminal of the
touch control panel, then it is possible to check and
repair the controls of the touch control panel; it is also
possible to check the sensor-related controls of the
touch control panel by using the dummy resistor(s).
B
Transistor
2SB1238
E
CB
Transistor
DTD143ES
3. Servicing of Touch Control Panel
We describe the procedures to permit servicing of the
touch control panel of the microwave oven and the precautions you must take when doing so.
To perform the servicing, power to the touch control panel
is available either from the power line of the oven itself or
from an external power source.
4. Servicing Tools
Tools required to service the touch control panel assembly.
1) Soldering iron: 30W
(It is recommended to use a soldering iron with a
grounding terminal.)
2) Oscilloscope: Single beam, frequency range: DC 10MHz type or more advanced model.
3) Others: Hand tools
(1) Servicing the touch control panel with power
supply of the oven :
CAUTION:
THE HIGH VOLTAGE TRANSFORMER OF THE
MICROWAVE OVEN IS STILL LIVE DURING
SERVICING AND PRESENTS A HAZARD .
T herefore, before checking the performance of the touch
control panel,
1) Disconnect the power supply cord, and then remove
outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power
transformer.
5) Ensure that these leads remain isolated from other
components and oven chassis by using insulation
tape.
6) After that procedure, re-connect the power supply cord.
After checking the performance of the touch control panel,
1) Disconnect the power supply cord.
2) Open the door and block it open.
3) Re-connect the leads to the primary of the power
transformer.
4) Re-install the outer case (cabinet).
5. Other Precautions
1) Before turning on the power source of the control unit,
remove the aluminium foil applied for preventing static
electricity.
2) Connect the connector of the key unit to the control unit
being sure that the lead wires are not twisted.
3) After aluminium foil is removed, be careful that abnormal voltage due to static electricity etc. is not applied
to the input or output terminals.
4) Attach connectors, electrolytic capacitors, etc. to PWB,
making sure that all connections are tight.
5) Be sure to use specified components where high
precision is required.
25
R-880B
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
WARNING: Avoid possible exposure to microwave energy. Please follow the instructions below before
operating the oven.
1. Disconnect the oven from power supply.
2. Make sure that a definite “click” can be heard when the
microwave oven door is unlatched. (Hold the door in a
closed position with one hand, then push the door open
button with the other, this causes the latch leads to rise,
it is then possible to hear a “click” as the door switches
operate.)
3. Visually check the door and cavity face plate for damage (dents, cracks, signs of arcing etc.).
1.
2.
3.
4.
5.
6.
Door does not close firmly.
Door hinge, support or latch hook is damaged.
The door gasket or seal or damaged.
The door is bent or warped.
There are defective parts in the door interlock system.
There are defective parts in the microwave generating
and transmission assembly.
7. There is visible damage to the oven.
Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS’, when carrying out any
of the following removal procedures:
WARNING FOR WIRING
heater, High voltage transformer and Oven cavity.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button, Turntable motor, Convection motor.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector certainly until its
pin is locked. And make sure that the wire leads
should not come off even if the wire leads is pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
To prevent an electric shock, take the following
manners.
1. Before wiring,
1) Disconnect the power supply.
2) Open the door and wedge the door open.
3) Discharge the high voltage capacitor and wait for
60 seconds.
2. Don't let the wire leads touch to the following parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, Grill heaters, Bottom
OUTER CASE REMOVAL
retaining clips on the cavity face plate.
7. Lift the entire case from the oven.
8. Discharge the H.V. capacitor before carrying out any
further work.
9. Do not operate the oven with the outer case removed.
N.B.; Step 1, 2 and 8 form the basis of the 3D checks.
To remove the outer case proceed as follows.
1. Disconnect oven from power supply.
2. Open the oven door and wedge it open.
3. Remove the two (2) screws holding the back plate to
the oven cavity rear plate.
4. Remove the back plate.
5. Remove the five (5) screws from rear and along the
side edge of case.
6. Slide the entire case back about 3cm to free it from
CAUTION: DISCHARGE HIGH VOLTAGE CAPACITOR
BEFORE
TOUCHING
ANY
OVEN
COMPONENT OR WIRING.
HIGH VOLTAGE COMPONENTS REMOVAL
(HIGH VOLTAGE CAPACITOR AND HIGH VOLTAGE RECTIFIER ASSEMBLY)
To remove the components, proceed as follows.
1. CARRY OUT 3D CHECKS.
2. Disconnect all the leads and terminals of high voltage
rectifier assembly from the high voltage capacitor.
3. Remove one (1) screw holding earth side terminal of
the high voltage rectifier assembly.
4. Remove one (1) screw holding capacitor holder to the
oven cavity rear plate.
26
R-880B
CAUTION: WHEN REPLACING HIGH VOLTAGE
RECTIFIER ASSEMBLY, ENSURE THAT
THE CATHODE (EARTH) CONNECTION
IS SECURELY FIXED TO THE CAPACITOR HOLDER AND BASE PLATE WITH
AN EARTHING SCREW.
5.
6.
7.
8.
Release the capacitor holder from the fan duct.
Remove the capacitor from the capacitor holder.
Now, the capacitor should be free.
Release H.V. wire A from the high voltage rectifier
assembly.
9. Now, the high voltage rectifier assembly should be free.
HIGH VOLTAGE TRANSFORMER REMOVAL
age transformer.
5. Remove the four (4) screws holding the transformer to
base plate.
6. Remove the transformer.
7. Now the high voltage transformer is free.
1. CARRY OUT 3D CHECKS.
2. Disconnect the filament leads of high voltage transformer from high voltage capacitor and the magnetron.
3. Disconnect the high voltage wire of high voltage
rectifier assembly from the high voltage transformer.
4. Disconnect the main wire harness from the high volt-
MAGNETRON REMOVAL
1. CARRY OUT 3D CHECKS.
2. Release the tabs of air intake duct from the chassis
support and the oven cavity.
3. Disconnect the high voltage wire of the high voltage
rectifier assembly and filament lead of the transformer
from the magnetron.
4. Remove the one (1) screw holding the chassis support
to the magnetron.
5. Move the air intake duct to left.
6. Carefully remove four (4) screws holding magnetron to
waveguide, when removing the screws hold the magnetron to prevent it from falling.
7. Remove the magnetron from the waveguide with care
so the magnetron antenna is not hit by any metal object
around the antenna.
CAUTION: WHEN REPLACING THE MAGNETRON,
BE SURE THE R.F. GASKET IS IN PLACE
AND THE MAGNETRON MOUNTING
SCREWS ARE TIGHTENED SECURELY.
POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL
Terminal
1. CARRY OUT 3D CHECKS.
2. Push the lever of positive lock® connector.
3. Pull down on the positive lock ® connector.
Positive lock®
connector
1
CAUTION: WHEN CONNECTING THE POSITIVE
LOCK ® CONNECTORS TO THE TERMINALS, CONNECT THE POSITIVE LOCK®
CONNECTOR SO THAT THE LEVER FACES
YOU
Push
Lever
2
Pull down
Figure C-1 Positive lock® connector
CONTROL PANEL ASSEMBLY REMOVAL
11.Release the two (2) tabs of the LCD holder holding the
CPU unit to the LCD holder.
12.Remove the LCD holder from the CPU unit.
13.Remove the two (2) screws holding the power unit to
the control panel frame.
14.Release the four (4) tabs of the control panel frame
holding the power unit to the control panel frame.
1 5. Now, the control unit (CPU unit + Power unit) is free.
NOTE: 1. Before attaching a new key unit, wipe off remaining adhesive on the control panel frame
surfaces completely with a soft cloth soaked in
alcohol.
2. When attaching the key unit to the control panel
frame, adjust the upper edge and right edge of
the key unit to the correct position of control
panel frame.
3. Stick the key unit firmly to the control panel
frame by rubbing with soft cloth not to scratch.
CONTROL PANEL ASSEMBLY
1. CARRY OUT 3D CHECKS.
2. Disconnect the main wire harness, thermistor harness,
AH sensor harness and the switch harness from the
power unit and control unit.
3. Straighten the tab of the oven cavity front flange
holding the tab of the control panel frame.
4. Lift up the control panel assembly.
5. Now, the control panel assembly is free.
CONTROL UNIT
6. Disconnect the flat ribbon cable from the connector CN-G.
7. Remove the two (2) screws holding the CPU unit to the
control panel frame.
8. Release the four (4) tabs of the control panel frame
holding the CPU unit to the control panel frame.
9. Release the liquid crystal display (LCD) from the LCD
holder.
10.Now, the LCD sheet is free.
27
R-880B
THERMISTOR REMOVAL
1. CARRY OUT 3D CHECKS.
2. Now, the back plate with the sub back plate should be
removed.
3. Disconnect the connector CN-D from the control unit.
4. Remove the one (1) screw holding the air duct to the
oven cavity rear plate.
5. Remove the air duct assembly from the oven cavity
rear plate.
6. Remove the one (1) screw holding the thermistor angle
to the oven cavity rear plate.
7. Remove the thermistor angle together with thermistor
from the oven.
8. Straighten the tab of the thermistor angle holding the
thermistor to the thermistor angle.
9. Remove the thermistor from the thermistor angle.
AH SENSOR ASSEMBLY REMOVAL
1. CARRY OUT 3D CHECKS.
2. Now, the back plate with the sub back plate should be
removed.
3. Disconnect the connector CN-F from the control unit.
4. Remove the two (2) screws holding the AH sensor
assembly to air duct assembly.
5. Now, the AH sensor assembly is free.
CONVECTION MOTOR REMOVAL
1. CARRY OUT 3D CHECKS.
2. Now, the back plate with the sub back plate should be
removed.
3. Disconnect the wire leads from the convection motor.
4. Remove the two (2) screws holding the conv. thermal
cover to the oven cavity rear plate.
5. Remove the four (4) screws holding the convection
duct to the oven cavity rear plate.
6. Remove the convection duct assembly from the oven
cavity rear plate.
7. Remove the one (1) nut and the two (2) washers
holding the convection fan to the convection motor
shaft.
8. Remove the convection fan.
9. Remove the three (3) screws holding the convection
duct to the conv. thermal cover.
10.Remove the convection duct with the conv. air angles
from the conv. thermal cover.
11.Remove the thermal insulation.
12.Remove the one (1) pipe holding the cooling fan to the
convection motor shaft.
13.Remove the cooling fan and the one (1) washer from
the convection motor shaft.
14.Remove the two (2) screws holding the convection
motor to the conv. thermal cover.
15.Remove the convection motor from the conv. thermal
cover.
16.Remove the one (1) ring from the convection motor
shaft.
17.Now, the convection motor is free.
FAN MOTOR REPLACEMENT
2) Remove the fan blade from the shaft of the fan
motor by pulling and rotating the fan blade with your
hand.
3) Now, the fan blade will be free.
REMOVAL
1. CARRY OUT 3D CHECKS.
2. Remove the one (1) screw holding the noise filter to the
chassis support.
3. Release the noise filter from the tab on the fan duct.
4. Disconnect the wire leads from the fan motor.
5. Remove the one (1) screw holding the capacitor holder
to the oven cavity rear plate.
6. Remove the one (1) screw holding the fan duct to the
oven cavity rear plate.
7. Release the tabs of the capacitor holder from fan duct.
8. Remove the fan duct from the oven.
9. Remove the fan blade from the fan motor shaft according to the following procedure.
1) Hold the edge of the rotor of the fan motor by using
a pair of groove joint pliers.
CAUTION:
• Make sure that any pieces do not enter the gap
between the rotor and the stator of the fan
motor. Because the rotor is easy to be shaven
by pliers and metal pieces may be produced.
• Do not let the pliers touch the coil of the fan
motor because the coil may be cut or damaged.
• Do not distort the bracket by touching with the
pliers.
CAUTION:
• Once the fan blade has been removed, it must
be replaced with a new one.
10.Remove the two (2) screws holding the fan motor to the
fan duct.
11.Now, the fan motor is free.
INSTALLATION
1.
Install the fan motor to the fan duct with the two (2)
screws.
2. Fix the fan blade to the fan motor shaft according to
the following procedure.
1) Hold the centre of the bracket which supports the
shaft of the fan motor on a flat table.
2) Install the fan blade to the shaft of fan motor by
pushing the fan blade with a small, light weight, ball
peen hammer or rubber mallet.
CAUTION:
• Do not hit the fan blade when installing it
because the bracket may be deformed.
• Make sure that the fan blade rotates smoothly
after installation.
28
R-880B
• Make sure that the axis of the shaft is not
slanted.
3. Install the fan duct to the oven cavity rear plate with the
one (1) screw.
4. Insert the tabs of the capacitor holder to the fan duct.
5. Install the capacitor holder to the oven cavity rear plate
with the one (1) screw.
6. Install the noise filter to the fan duct and the chassis
support with the one (1) screw.
7. Re-connect the wire leads to the fan motor.
Coil
Shaft
Groove joint pliers
Stator
Gap
Bracket
Shaft
Axis
Rotor
Stator
These are the positions
that should be pinched
with pliers
Table
Center of
bracket
Rotor
Rear view
Side view
TURNTABLE MOTOR REPLACEMENT
remove the two (2) screws holding the turntable motor.
5. Now, the turntable motor is free.
6. After replacement use the one (1) screw provided with
the turntable motor assembly to fit turntable motor
cover.
1. Disconnect the oven from the power supply.
2. Remove the turntable motor cover by snipping of
material in four corners.
3. Where the corners have been snipped off, bend corner
areas flat. No sharp edge must be evident after removal of turntable motor cover.
4. Disconnect the wire leads from the turntable motor and
NOTE: The one (1) screw to fit the turntable motor cover
should be XHTSD40P08RV0.
OVEN LAMP REMOVAL
1. CARRY OUT 3D CHECKS.
2. Remove the two (2) screws holding the air guide to the
top of the oven cavity.
3. Straighten the tab holding the lamp cover to the top of
the oven cavity.
4. Remove the lamp cover.
5. Disconnect the wire leads from the oven lamp.
6. Straighten the tab holding the oven lamp.
7. Remove the oven lamp from the top of the oven cavity.
WARNING: Do not touch the oven lamp right after it is
turned off or during it is turned on. Because the oven lamp is halogen type and
it is very hot then.
AC PLUG AND POWER SUPPLY CORD REPLACEMENT
2. Install the green/yellow wire lead of the power supply
cord to the chassis support with one (1) screw and tight
the screw.
3. Connect the brown and blue wire leads of power supply
cord into the terminals of noise filter, referring to
pictorial diagram.
4. Now the power supply cord is installed.
5. Connect the power supply cord to the AC plug, referring to figure C-2(b).
5-1. Connect the green/yellow wire lead of the power
supply cord to the AC plug terminal which is marked
with the earth symbol ∞ or letter YELLOW GREEN.
And tight the screw.
5-2. Connect the blue wire lead of the power supply cord
to the AC plug terminal which is marked with letter N
or BLUE. And tight the screw.
5-3. Connect the brown wire lead of the power supply cord
to the AC plug terminal which is marked with letter L
or BROWN. And tight the screw.
6. Re-install the power supply cord to the AC plug body,
referring to figure C-2(b).
7. Re-install the AC plug cover to the AC plug body with
one (1) screw and tight screw.
8. Now the AC plug is installed.
Removal
1. CARRY OUT 3D CHECKS.
2. Remove the one screw holding the plug body to the
plug cover.
3. Remove the plug cover from the plug body.
4. Loosen the three (3) screws holding the three wire
leads of the power supply cord to the three (3) terminals
of AC plug.
5. Remove the power supply cord from the AC plug.
6. Now the AC plug is free.
7. Disconnect the brown wire and blue wire of the power
supply cord from the noise filter.
8. Remove the one (1) screw holding green/yellow wire
lead of the power supply cord to the oven cavity rear
plate.
9. Release the moulding cord stopper of the power supply
cord from the square hole of the oven cavity back plate,
referring to figure C-2(d).
10.Now the power supply cord is free.
Re-install
1. Insert the moulding cord stopper of the power supply
cord to the square hole of the oven cavity back plate,
referring to figure C-2(d).
29
R-880B
Oven Cavity
Back Plate
Screw
Power Supply Cord
Screw
Brown Wire
Plug Body
Bule Wire
Green/Yelow
Wire
Plug Cover
L
N
Chassis
Support
WHT
RED
T1
T2
Noise Filter
Figure C-2(a). AC Plug
Figure C-2(c). Wiring to Noise filter
Screw
Brown Wire Lead
L
Screw
Moulding
Cord Stopper
Power Supplu Cord
N
Power
Supply Cord
Oven Cavity
Rear Plate
Green/Yelow
Wire Lead
Screw
Blue Wire Lead
Square Hole
Figure C-2(b). AC Plug Wiring
Figure C-2(d). Power supply cord position
GRILL HEATERS (TOP HEATERS) REMOVAL
1. CARRY OUT 3D CHECKS.
2. Remove the one (1) screw holding the exhaust duct to
the oven cavity.
2. Remove the exhaust duct from the oven cavity.
4. Disconnect the wire leads from the grill heaters.
5. Lay down the two (2) tabs holding the reflector to the
oven cavity.
6. Remove the reflector from the oven cavity by sliding it
leftward.
7. Remove the grill heaters and the short terminal together from the oven cavity top plate.
8. Remove the two (2) screws holding the short terminal
to the grill heaters.
9. Now the individual grill heaters are free.
BOTTOM HEATER REMOVAL
1. CARRY OUT 3D CHECKS
2. Remove the fan duct from the oven cavity, referring to
"FAN MOTOR REPLACEMENT".
3. Disconnect the wire leads from the bottom heater.
4. Remove the two (2) nuts holding the bottom heater with
the bottom heater angle and the heat seal spring to the
oven cavity right wall.
5. Remove the two (2) nuts holding the bottom heater with
the bottom heater angle and the heat seal spring to the
oven cavity left wall.
6. Remove the bottom heater from the oven cavity .
1ST. LATCH SWITCH, 2ND. INTERLOCK RELAY CONTROL SWITCH, AND MONITOR SWITCH REMOVAL
Latch Hook
1. CARRY OUT 3D CHECKS.
2. Remove the control panel assembly referring to "CONTROL PANEL ASSEMBLY REMOVAL".
3. Remove the switch lever.
4. Disconnect the leads from all switches.
5. Remove the two (2) screws holding the latch hook to
the oven cavity.
6. Remove the latch hook.
7. Push the retaining tab slightly and remove the switch.
Tab
2nd. Interlock
Relay Control
Switch
Monitor Switch
Tab
1st. Latch Switch
Tab
Figure C-3. Switches
30
R-880B
1ST. LATCH SWITCH, 2ND. INTERLOCK RELAY CONTROL SWITCH
AND MONITOR SWITCH ADJUSTMENT
If the 1st. latch switch, 2nd. interlock relay control switch
and monitor switch do not operate properly due to a misadjustment, the following adjustment should be made.
1. CARRY OUT 3D CHECKS.
2. Loosen the two (2) screws holding the latch hook to the
oven cavity front flange.
3. With the door closed, adjust the latch hook by moving
it back and forward or up and down. In and out play of
the door allowed by the latch hook should be less than
0.5 mm. The horizontal position of the latch hook
should be placed where the monitor switch has activated with the door closed. The vertical position of the
latch hook should be placed where the 1st. latch switch
and 2nd. interlock relay control switch have activated
with the door closed.
4. Secure the screws with washers firmly.
5. Make sure of the 1st. latch switch, 2nd. interlock relay
control switch and monitor switch operation. If those
switches have not activated with the door closed, two
(2) screw holding latch hook to oven cavity front flange
and adjust the latch hook position.
ing and pulling the door toward the oven face. The
results (play of the door) should be less than 0.5mm.
2. The contacts (COM-NO) of the 1st. latch switch and
2nd. interlock relay control switch interrupt the circuit
before the door can be opened.
3. The contacts (COM-NC) of the monitor switch close
when the door is opened.
4. Re-install outer case and check for microwave leakage
around the door with an approved microwave survey
meter. (Refer to Microwave Measurement Procedure.)
Latch Heads
Latch Hook
2nd. Interlock
Relay Control
Switch
Door
Monitor Switch
1st. Latch Switch
After adjustment, make sure of following:
Switch Lever
1. In and out play of door remains less than 0.5 mm when
latched position. First check latch hook position, push-
Figure C-4 Latch Switches Adjustment
DOOR REPLACEMENT
with releasing latch spring from door frame and latch
head.
13.Now, latch head and latch spring are free.
14.Remove the two (2) screws holding the glass stopper
to the door frame.
15.Remove the glass stopper from the door frame.
16.Slide the front door glass left and then slide upwards
to release the tabs holding it.
17.Now, the front door glass is free
REMOVAL
1. Disconnect the oven from power supply.
2. Push the open button and open the door slightly.
3. Insert an putty knife (thickness of about 0.5mm) into the
gap between the choke cover and door frame as shown
in Figure C-5 to free engaging parts.
4. Pry the choke cover by inserting a putty knife as shown
in Figure C-5.
5. Release choke cover from door panel.
6. Now choke cover is free.
RE-INSTALL
1. Re-install the front door glass to the door frame as
follows.
1) Insert the lower edge of the front door glass into the six
(6) tabs of the door frame.
2) Slide the front door glass upwards and insert the upper
edge of the front door glass into the five (5) tabs of the
door frame.
3) Slide the front door glass righ and insert the right
edge of the front door glass into the two (2) tabs of the
door frame.
2. Re-install the glass stopper to the door frame as
follows.
1) Re-install the glass stopper to the door frame so that
the two (2) holes of the glass stopper meet the two (2)
pins of the door frame.
2) Hold the glass stopper to the door frame with the two
(2) screws.
3. Re-install the latch spring to the latch head. Re-install
the latch spring to the door frame. Re-install latch head
to door frame.
4. Re-install door panel to door frame by fitting seven (7)
tabs of door frame to seven (7) holes of door panel.
5. Hold the door panel to the door frame with four (4)
Choke Cover
Putty Knife
Door Frame
Figure C-5. Door Disassembly
7. Release two (2) pins of door panel from two (2) holes
of upper and lower oven hinges by lifting up.
8. Now, door sub assembly is free from oven cavity.
9. Remove the four (4) screws holding the door panel to
the door frame.
10.Release door panel from seven (7) tabs of door frame
by sliding door panel downward.
11.Now, door panel is free.
12.Slide latch head upward and remove it from door frame
31
R-880B
screws.
6. Catch two (2) pins of door panel on two (2) hole of upper
and lower oven hinges.
7. Re-install choke cover to door panel by pushing.
Note: After any service to the door;
(A) Make sure that door sensing switch and primary
latch switch are operating properly. (Refer to
chapter "Test Procedures".).
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave radiation emission limitation standards.
(Refer to Microwave Measurement Procedure.)
After any service, make sure of the following :
1. Door latch heads smoothly catch latch hook through
latch holes and that latch head goes through centre of
latch hole.
2. Deviation of door alignment from horizontal line of
cavity face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Check for microwave leakage around door with an
approved microwave survey meter. (Refer to Microwave Measurement Procedure.)
Note:
The door on a microwave oven is designed to act
as an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
cycle. This function does not require that door be
air-tight, moisture (condensation)-tight or lighttight. Therefore, occasional appearance of moisture, light or sensing of gentle warm air movement
around oven door is not abnormal and do not in
themselves indicate a leakage of microwave energy from oven cavity.
Pin
Upper
Oven
Hinge
Upper Oven
Hinge
Door
Panel
Lower
Oven
Hinge
Choke Cover
Pin
Lower
Oven
Hinge
Figure C-6. Door Replacement
32
R-880B
MICROWAVE MEASUREMENT
After adjustment of door latch switches, monitor switch
and door are completed individually or collectively, the
following leakage test must be performed with a survey
instrument and it must be confirmed that the result meets
the requirements of the performance standard for microwave oven.
2.
3.
REQUIREMENT
The safety switch must prevent microwave radiation emission in excess of 5mW/cm2 at any point 5cm or more from
external surface of the oven.
PREPARATION FOR TESTING:
4.
Before beginning the actual test for leakage, proceed as
follows;
1. Make sure that the test instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement
for instrumentations as prescribed by the performance
standard for microwave ovens must be used for testing.
5.
6.
Recommended instruments are:
NARDA 8100
NARDA 8200
HOLADAY HI 1500
SIMPSON 380M
Place the oven tray into the oven cavity.
Place the load of 275 ± 15ml of water initially at 20 ± 5˚C
in the centre of the oven tray. The water container
should be a low form of 600 ml beaker with inside
diameter of approx. 8.5cm and made of an electrically
non-conductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that
any leakage is measured accurately.
Close the door and turn the oven ON with the timer set
for several minutes. If the water begins to boil before
the survey is completed, replace it with 275ml of cool
water.
Move the probe slowly (not faster that 2.5cm/sec.)
along the gap.
The microwave radiation emission should be measured at any point of 5cm or more from the external
surface of the oven.
SHARP
mW cm 2
mW cm 2
Microwave leakage measurement at 5 cm distance
33
THERMAL
CUT-OUT(OVEN)
34
RY4
COM.
1ST.
LATCH SWITCH
Figure O-2 Oven Schematic-Microwave cooking Condition
H.V. RECTIFIER
MAGNETRON
T2
FM
H.V. RECTIFIER
CAPACITOR
1.07µF
AC2200V
MONITOR SWITCH
GRILL HEATER (TOP)
N.O.
N.O.
COM.
MONITOR RESISTOR
0.8/ 20W
N.O.
MAGNETRON
HIGH VOLTAGE
TRANSFORMER
RY4
COM.
RY2
RY6
RY5
RY1
RY3
A3
A5
D3
D1
COM.
COM.
N.O.
BOTTOM HEATER
TURNTABLE
MOTOR
TTM
OVEN LAMP
ASYMMETRIC
RECTIFIER
1ST.
LATCH SWITCH
CAPACITOR
1.07µF
AC2200V
MONITOR SWITCH
MONITOR RESISTOR
0.8/ 20W
N.O.
T1
FUSE
M10A
GRILL HEATER (TOP)
CONTROUNIT
N.O.
N.O.
COM.
OL
FAN MOTOR
CONVECTION
MOTOR
CM
THERMISTOR
CONTROUNIT
HIGH VOLTAGE
TRANSFORMER
RY3
RY2
RY6
COM.
COM.
A3
RY5
RY1
THERMAL CUT-OUT
(MG.)
T1
T2
FUSE
M10A
BOTTOM HEATER
FM
A5
D3
D1
B2
B1
F1
F2
A1
LINE BYPASS CAPACITOR
0.0033µF/ 250V
RESISTOR 10M/ 0.5W
L
THERMAL CUT-OUT
(MG.)
TURNTABLE
MOTOR
TTM
OVEN LAMP
OL
FAN MOTOR
CONVECTION
MOTOR
CM
THERMISTOR
AH SENSOR
2ND. INTERLOCK
RELAY CONTROL
SWITCH
F3
FUSE 15A
NOISE SUPPRESSION COIL
RESISTOR 680 k/ 0.5W
LINE BYPASS CAPACITOR
0.0033µF/ 250V
BRN
LIVE
LINE CROSS CAPACITOR
0.22µ/250V
EARTH
G-Y
220 V ~ 50Hz
NOTE:
B2
A1
THERMAL
CUT-OUT(OVEN)
B1
F1
F2
F3
LINE BYPASS CAPACITOR
0.0033µF/ 250V
N
NEUTRAL
BLU
NOISE FILTER UNIT
2ND. INTERLOCK
RELAY CONTROL
SWITCH
N.O.
LINE BYPASS CAPACITOR
0.0033µF/ 250V
RESISTOR 10M/ 0.5W
RESISTOR 680 k/ 0.5W
NOISE SUPPRESSION COIL
FUSE 15A
L
NOISE FILTER UNIT
AH SENSOR
LIVE
LINE CROSS CAPACITOR
0.22µ/250V
EARTH
G-Y
BRN
220 V ~ 50Hz
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2.
:
OR CLOCK APPEAR ON DISPLAY.
ASYMMETRIC
RECTIFIER
N
NEUTRAL
BLU
R-880B
Indicates components with potential above 250 V.
RY2: 2ND.
INTERLOCK
RELAY
Figure O-1 Oven Schematic-OFF Condition
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. MICROWAVE POWER LEVEL PAD PRESSED ONCE(100%).
3. COOKING TIME PROGRAMMED.
4. START PAD TOUCHED.
RY2: 2ND.
INTERLOCK
RELAY
THERMAL
CUT-OUT(OVEN)
35
RY4
COM.
1ST.
LATCH SWITCH
Figure O-3(b) Oven Schematic-Grill cooking Condition (BOTTOM HEATER mode)
H.V. RECTIFIER
MONITOR RESISTOR
0.8/ 20W
MAGNETRON
T2
FM
CM
H.V. RECTIFIER
CAPACITOR
1.07µF
AC2200V
MONITOR SWITCH
GRILL HEATER (TOP)
N.O.
N.O.
COM.
MONITOR RESISTOR
0.8/ 20W
N.O.
MAGNETRON
HIGH VOLTAGE
TRANSFORMER
RY4
COM.
RY2
RY6
RY5
RY1
RY3
A3
A5
D3
D1
COM.
COM.
N.O.
BOTTOM HEATER
TURNTABLE
MOTOR
TTM
OVEN LAMP
ASYMMETRIC
RECTIFIER
1ST.
LATCH SWITCH
CAPACITOR
1.07µF
AC2200V
MONITOR SWITCH
N.O.
T1
FUSE
M10A
GRILL HEATER (TOP)
CONTROUNIT
N.O.
N.O.
COM.
OL
FAN MOTOR
CONVECTION
MOTOR
THERMISTOR
B2
B1
F1
F2
A1
CONTROUNIT
HIGH VOLTAGE
TRANSFORMER
RY3
RY2
RY6
RY5
COM.
COM.
N.O.
A3
A5
D3
THERMAL CUT-OUT
(MG.)
L
T1
T2
FUSE
M10A
BOTTOM HEATER
FM
CM
RY1
AH SENSOR
2ND. INTERLOCK
RELAY CONTROL
SWITCH
F3
LINE BYPASS CAPACITOR
0.0033µF/ 250V
RESISTOR 10M/ 0.5W
RESISTOR 680 k/ 0.5W
LINE BYPASS CAPACITOR
0.0033µF/ 250V
FUSE 15A
NOISE SUPPRESSION COIL
LINE CROSS CAPACITOR
0.22µ/250V
EARTH
BRN
LIVE
THERMAL CUT-OUT
(MG.)
TURNTABLE
MOTOR
TTM
OVEN LAMP
OL
FAN MOTOR
CONVECTION
MOTOR
D1
B2
THERMAL
CUT-OUT(OVEN)
B1
F1
A1
NOISE FILTER UNIT
F2
F3
LINE BYPASS CAPACITOR
0.0033µF/ 250V
N
G-Y
220 V ~ 50Hz
NOISE FILTER UNIT
2ND. INTERLOCK
RELAY CONTROL
SWITCH
LINE BYPASS CAPACITOR
0.0033µF/ 250V
RESISTOR 10M/ 0.5W
RESISTOR 680 k/ 0.5W
NOISE SUPPRESSION COIL
FUSE 15A
L
NEUTRAL
BLU
NOTE:
THERMISTOR
LIVE
LINE CROSS CAPACITOR
0.22µ/250V
EARTH
G-Y
BRN
220 V ~ 50Hz
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. GRILL PAD TOUCHED ONCE.
3. COOKING TIME PROGRAMMED.
4. STRAT PAD TOUCHED.
ASYMMETRIC
RECTIFIER
N
NEUTRAL
BLU
R-880B
Indicates components with potential above 250 V.
RY2: 2ND.
INTERLOCK
RELAY
Figure O-3(a) Oven Schematic-Grill cooking Condition (TOP HEATER mode)
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. GRILL PAD TOUCHED TWICE.
3. COOKING TIME PROGRAMMED.
4. STRAT PAD TOUCHED.
RY2: 2ND.
INTERLOCK
RELAY
THERMAL
CUT-OUT(OVEN)
36
RY4
COM.
1ST.
LATCH SWITCH
Figure O-4 Oven Schematic-Convection cooking Condition
H.V. RECTIFIER
MAGNETRON
T2
FM
H.V. RECTIFIER
CAPACITOR
1.07µF
AC2200V
MONITOR SWITCH
GRILL HEATER (TOP)
N.O.
N.O.
COM.
MONITOR RESISTOR
0.8/ 20W
N.O.
MAGNETRON
HIGH VOLTAGE
TRANSFORMER
RY4
COM.
RY2
RY6
RY5
RY1
RY3
A3
A5
D3
D1
COM.
COM.
N.O.
BOTTOM HEATER
TURNTABLE
MOTOR
TTM
OVEN LAMP
ASYMMETRIC
RECTIFIER
1ST.
LATCH SWITCH
CAPACITOR
1.07µF
AC2200V
MONITOR SWITCH
MONITOR RESISTOR
0.8/ 20W
N.O.
T1
FUSE
M10A
GRILL HEATER (TOP)
CONTROUNIT
N.O.
N.O.
COM.
OL
FAN MOTOR
CONVECTION
MOTOR
CM
THERMISTOR
B2
B1
F1
F2
A1
CONTROUNIT
HIGH VOLTAGE
TRANSFORMER
RY3
RY2
RY6
COM.
COM.
A3
RY5
THERMAL CUT-OUT
(MG.)
L
T1
T2
FUSE
M10A
BOTTOM HEATER
FM
A5
RY1
AH SENSOR
2ND. INTERLOCK
RELAY CONTROL
SWITCH
F3
LINE BYPASS CAPACITOR
0.0033µF/ 250V
RESISTOR 10M/ 0.5W
RESISTOR 680 k/ 0.5W
LINE BYPASS CAPACITOR
0.0033µF/ 250V
FUSE 15A
NOISE SUPPRESSION COIL
LINE CROSS CAPACITOR
0.22µ/250V
EARTH
BRN
LIVE
THERMAL CUT-OUT
(MG.)
TURNTABLE
MOTOR
TTM
OVEN LAMP
OL
FAN MOTOR
CONVECTION
MOTOR
CM
D3
N
G-Y
220 V ~ 50Hz
NOTE:
D1
B2
B1
F1
F2
A1
THERMAL
CUT-OUT(OVEN)
THERMISTOR
2ND. INTERLOCK
RELAY CONTROL
SWITCH
F3
LINE BYPASS CAPACITOR
0.0033µF/ 250V
NOISE FILTER UNIT
N.O.
LINE BYPASS CAPACITOR
0.0033µF/ 250V
RESISTOR 10M/ 0.5W
RESISTOR 680 k/ 0.5W
NOISE SUPPRESSION COIL
FUSE 15A
L
NEUTRAL
BLU
NOISE FILTER UNIT
AH SENSOR
LIVE
LINE CROSS CAPACITOR
0.22µ/250V
EARTH
G-Y
BRN
220 V ~ 50Hz
SCHEMATIC
NOTE: CONDITION OF OVEN FOR GRILL COOKING
1. DOOR CLOSED.
2. GRILL PAD THREE TIMES.
3. COOKING TIME PROGRAMMED.
4. STRAT PAD TOUCHED.
ASYMMETRIC
RECTIFIER
N
NEUTRAL
BLU
R-880B
Indicates components with potential above 250 V.
RY2: 2ND.
INTERLOCK
RELAY
Figure O-3(c) Oven Schematic-Grill cooking Condition (TOP AND BOTTOM GRILL mode)
SCHEMATIC
NOTE: CONDITION OF OVEN FOR GRILL COOKING
1. DOOR CLOSED.
2. CONVECTION PAD TOUCHED.
3. TEMPERATURE PAD TOUCHED.
4. COOKING TIME PROGRAMMED.
5. STRAT PAD TOUCHED.
RY2: 2ND.
INTERLOCK
RELAY
THERMAL
CUT-OUT(OVEN)
1ST.
LATCH SWITCH
37
RY4
COM.
H.V. RECTIFIER
MONITOR RESISTOR
0.8/ 20W
MAGNETRON
T2
FM
CM
H.V. RECTIFIER
CAPACITOR
1.07µF
AC2200V
MONITOR SWITCH
GRILL HEATER (TOP)
N.O.
N.O.
COM.
MONITOR RESISTOR
0.8/ 20W
N.O.
MAGNETRON
HIGH VOLTAGE
TRANSFORMER
RY4
COM.
RY2
RY6
RY5
RY1
RY3
A3
A5
D3
D1
COM.
COM.
N.O.
BOTTOM HEATER
TURNTABLE
MOTOR
TTM
OVEN LAMP
ASYMMETRIC
RECTIFIER
1ST.
LATCH SWITCH
CAPACITOR
1.07µF
AC2200V
MONITOR SWITCH
N.O.
T1
FUSE
M10A
GRILL HEATER (TOP)
CONTROUNIT
N.O.
N.O.
COM.
OL
FAN MOTOR
CONVECTION
MOTOR
THERMISTOR
B2
B1
F1
F2
A1
CONTROUNIT
HIGH VOLTAGE
TRANSFORMER
RY3
RY2
RY6
RY5
COM.
COM.
A3
A5
D3
RY1
THERMAL CUT-OUT
(MG.)
L
T1
T2
FUSE
M10A
BOTTOM HEATER
FM
CM
D1
AH SENSOR
2ND. INTERLOCK
RELAY CONTROL
SWITCH
F3
LINE BYPASS CAPACITOR
0.0033µF/ 250V
RESISTOR 10M/ 0.5W
RESISTOR 680 k/ 0.5W
LINE BYPASS CAPACITOR
0.0033µF/ 250V
FUSE 15A
NOISE SUPPRESSION COIL
LINE CROSS CAPACITOR
0.22µ/250V
EARTH
BRN
LIVE
THERMAL CUT-OUT
(MG.)
TURNTABLE
MOTOR
TTM
OVEN LAMP
OL
FAN MOTOR
CONVECTION
MOTOR
THERMISTOR
B2
THERMAL
CUT-OUT(OVEN)
B1
F1
F2
NOISE FILTER UNIT
A1
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. MIX PAD TOUCHED THREE TIMES/FOUR TIMES.
3. COOKING TIME PROGRAMMED.
4. STRAT PAD TOUCHED.
2ND. INTERLOCK
RELAY CONTROL
SWITCH
F3
LINE BYPASS CAPACITOR
0.0033µF/ 250V
N
G-Y
220 V ~ 50Hz
NOISE FILTER UNIT
N.O.
LINE BYPASS CAPACITOR
0.0033µF/ 250V
RESISTOR 10M/ 0.5W
RESISTOR 680 k/ 0.5W
NOISE SUPPRESSION COIL
FUSE 15A
L
NEUTRAL
BLU
NOTE:
AH SENSOR
LIVE
LINE CROSS CAPACITOR
0.22µ/250V
EARTH
G-Y
BRN
220 V ~ 50Hz
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. MIX PAD TOUCHED ONCE/TWICE.
3. COOKING TIME PROGRAMMED.
4. STRAT PAD TOUCHED.
ASYMMETRIC
RECTIFIER
N
NEUTRAL
BLU
R-880B
Indicates components with potential above 250 V.
NOTE: The microwave relay RY2 and heater relay RY3 could not turn on simultaneously.
RY2: 2ND.
INTERLOCK
RELAY
Figure O-5(a) Oven Schematic-Mix cooking Condition (High Mix Top Grill mode / Low Mix Top Grill mode)
NOTE: The microwave relay RY2 and heater relay RY4 could not turn on simultaneously.
RY2: 2ND.
INTERLOCK
RELAY
Figure O-5(b) Oven Schematic-Mix cooking Condition (High Mix Bottom Grill mode / Low Mix Bottom Grill mode)
1
2
3
38
4
RY2
1
CN-A
RY5
RY1
T1
5
ORG
BRN
BLK
5
RY6
5 RED
CN-A
1 GRY
2
3 ORG
4
BRN
ORG
ORG
COM
1ST.
LATCH
SWITCH COM.
GRY
H
6
WHT
TURNTABLE
MOTOR
BLK
WHT
RED
OVEN LAMP
(HALOGEN LAMP)
BOTTOM HEATING
ELEMENT
CONNECTOR
WHT
RED
WHT
EARTH
L
BRN
RED
WHT
WHT
NOISE
FILTER
M10A
GRY
GRY
FAN
MOTOR
ORG
GRY
RED
RED
BRN
THERMAL
CUT-OUT
125°C(MG)
WHT
RED
CONVECTION
MOTOR
RED
WHT
HIGH VOLTAGE
TRANSFORMER
H.V.
CAPACITOR
ASYMMETRIC
RECTIFIER
H.V.
RECTIFIER
H.V.WIRE A
MAGNETRON
HIGH VOLTAGE COMPONENTS
BRN
T2
BLU
LIVE
T1
QRG
N
BRN
5
WHT
N.O.
WHT
WHT
GRY
MONMITOR
SWITCH
N.C.
GRN
GRN
COM.
BLK
WHT
GRY
G–Y
POWER SUPPLY
CORD
4
Figure S-1. Pictrorial Diagram
RED
RY4
RY3
SP1
1
CN-B
2
CN-D
3
CN-B
2 GRY
1 GRN
GRY
GRN
N.O.
GRILL HEATER
THERMAL
CUT-OUT
(OVEN)
WHT
WHT
WHT
3
ORG
RED
ORG
CN-C
CN-F
2ND. INTERLOCK
RELAY CONTROL
SWITCH
BLK
BLK
CN-F
2
BRN
BLK
G
CN-C
3
2
1
A
CONTROL PANEL
CN-G
F
THERMISTOR
C
NEUTRAL
D
AH SENSOR
1
15A
B
RED WHT
CN-F
1 BLK
2 RED
3 WHT
R-880B
6
A
E
B
C
D
E
F
G
H
MONITOR
RESISTOR
R-880B
2
1
4
3
6
5
A
A
Q2 2SB1238
R4 27
C10
D1-4
11ES1
2SB1238
c
R2 680 1/2w
+
–
C2
GND
C3
VC
C1
VA
C9
VR
C4
INT
C5
BUZZER
C15
FAN MOTOR
C16
CONVECTION
MOTOR
C6
OVEN LAMP
TURNTABLE
MOTOR
C14
BOTTOM
HEATER
C8
TOP
HEATER
C11
N.C.
C7
MICRO
C17
OVEN
THERMISTOR
C13
N.C.
C12
DOOR
SWITCH
C4 10µ/35v
Q1
C3 0.1µ/50v
HZ16-1
ZD1
D2
R1 2.4k
D4
b
(J1)
C
B
+
6
d 1
a
LED
R5 4.7k
D1
D3
–
4
D6
C2 1000µ/35v
8
A1
10G471K
AC220V
50Hz
VRS1
B
D5
C1 0.1µ/50v
T1
R3 510 1/2w
C
SP1
D12
RY5
FAN MOTOR
R6 3.3k
A3
RY1
D
D7
D
RY6
N.O.
Q3
DTD143ES
COM
–
+
OVEN LAMP
TURNTABLE
MOTOR
A5
D11
CONVECTION
MOTOR
C5
10µ/35v
RY4
BOTTOM
HEATER
N.O.
D10
E
E
COM
RY3
D9
N.O.
TOP
HEATER
COM
RY2
D8
N.O.
F
MICRO
F
COM
D3
G
D1
B2
DOOR SWITCH
OVEN THERMISTOR
NOTE
B1
G
: IF NOT SPECIFIED, 1/4W ± 5%
: IF NOT SPECIFIED, 1SS270A
H
H
Figure S-2. Power Unit Circuit
1
2
4
3
39
5
6
C3
C5
C1
C10
C9
C15
C16
VC
BUZZER
VA
LED
VR
FAN
MOTOR
CONVECTION
MOTOR
4
C7
MICRO
5
OVEN
C17
THERMISTOR
C13
D30
D23
D22
G
C12
C11
C14
BOTTOM
HEATER
DOOR
SWITCH
C8
TOP
HEATER
C6
C2
OVEN LAMP
TURNTABLE
MOTOR
C4
GND
C11 0.1µ/50v
+
–
Q20
DTA123JKA
Q21
DTA123JKA
C21
0.1µ/50v
Q22
DTA123JKA
Q23
DTA143EKA
Q24
DTA143EKA
Q25
DTA143EKA
LD10 LD9 LD8 LD7 LD6
IC2
BA4558
F2
F3
1.8kF
R101
IC2
0.015µ/25v
C102
(J11)
(J12)
R103 10k
C104
C103
(J10)
(J15) 4.7k
R106 47k
R107 620k
R108 300k
R109 150k
R110 75kF
R111 37.4kF
R102 360kF
+
R10 1k
(J14) 4.7k
H
6
R72 100k
C63 330p/50v
C62 330p/50v
C61 330p/50v
C60 330p/50v
R75 100k
R74 100k
R73 100k
R70 15k
R14
1k
R13
1k
R69 15k
Figure S-3. CPU Unit Circuit
R80 180kF
R11 4.7k
(J13) 4.7k
C1
VL1
AN7
AN6
AN5
AN4
AN3
AN2
AN1
AN0
P57
P56
P55
P54
P53
P52
P51
P50
P47
P46
P45
P44
INT1
INT0
P41
P40
P77
P76
P75
P74
30
25
20
15
10
5
CF1 4.19MGW
R56
1M
4
5
3
G6
8
220˚C
CLOOK
CONVEC
PREHEAT
Pasta
9
230˚C
MORE
250˚C
130˚C
INSTANT COOK
START
0
G7
150˚C
G8
160˚C
R63 15k
6
GRILL
180˚C
Jacket
Potato
Reheat
Pie
200˚C
POWER
LEVEL
7
1
40˚C
G4
2
70˚C
G5
80 SEG10
SEG11
SEG12
SEG13
SEG14
75 SEG15
SEG16
SEG17
SEG18
SEG19
70 SEG20
SEG21
SEG22
SEG23
SEG24
65 SEG25
SEG26
SEG27
SEG28
SEG29
60 SEG30
SEG31
SEG32
SEG33
SEG34
55 SEG35
SEG36
SEG37
SEG38
SEG39
LESS
Rice
G3
EASY
DEFROST
REHEAT
SENSOR
MIX
G2
G1
MULTI
HELP
COOK
STOP
Fresh
Vegetables
CLEAR
Frozen
CONVENIENCE
Vegetables
/PIZZA
1
5
AH SENSOR
F1
C13
0.1µ/50v
R30 4.7k
C30
R112 3.57kD
C10 47µ/16v
LD1 LD2 LD3 LD4 LD5
R31 15k
C14
D101
MA152WA
R15 4.7k
R90 330 1w
0.1µ/50v
C101
R105 3.32kD
Q40
DTA143EKA
R83 15k
Q10
2SA1037AK
R104 47k
51
95
Q11
DTA143EKA
C80
90
ZD10
UDZ4.3B
R82 10kF
40
R55 4.7k
R12
1k
COOK
HELP
4
R81 180F
3
R60 15k
3
(J1)
C12
0.1µ/50v
R68 15k
C2
VL2
VL3
COM0
COM1
COM2
COM3
AVSS
VREF
VCC
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
85
2
IC-1
RH-IZA927DR
E
R61 15k
INT
R64 15k
: IF NOT SPECIFIED, 0.01µF / 25v
R65 15k
: IF NOT SPECIFIED, 1/10W ± 5%
R66 15k
: IF NOT SPECIFIED, 1SS355
R67 15k
1
R71 15k
C
G12 G11 G10 G 9
B
SEG45
SEG44
SEG43
SEG42
SEG41
SEG40
SEG39
SEG38
SEG37
SEG36
SEG35
SEG34
SEG33
SEG32
COM5
COM4
COM3
COM2
COM1
SEG15
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
F
2
P73
P72
P71
P70
RESET 35
P81
P80
XIN
XOUT
VSS
P27
P26
P25
P24
45
P23
P22
P21
P20
P17
50
P16
1
R62 15k
NOTE
R-880B
6
A
A
B
C
D
D
E
F
G
H
R-880B
2
1
4
3
6
5
A
A
DIP
R3
CN - C 18
B
1
1
2
D6
CN - D
3
Q1
B
3
D5
1
C
CN - B
4
D11
RY6
1
AC
R1
E
R2
C2
C
2
ZD1
C5
E
Q3
SP1
D1
D3
C1
RY3
T-H
D
B
R4
E
Q2
R5
B
D8
C3
C4
R6
D9
D10
B
D
1
D2
8
RY4
B-H
D4
E
E
6
RY2
MICRO
S
P
4
VRS1
F
F
T1
5
(J1)
FAN
1
5
CON
AC
D7
CN - A
6
LOT NO.
G
D12
RY1
G
RY5
F
H
H
Figure S-4. Printed Wiring Board
1
2
4
3
41
5
6
R-880B
PARTS LIST
Note: The parts marked "∆" may cause undue microwave exposure.
The parts marked "*" are used in voltage more than 250V.
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
AG
AH
AH
AH
AU
AT
AW
AY
AY
AW
AW
AP
AF
AE
AD
AX
BD
BB
AK
AH
AK
BR
BN
BN
AN
AP
AW
AX
1
1
1
2
AW
AZ
AX
AC
1
1
1
2
1
1
1
1
2
4
8
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
4
BE
AC
AB
AK
AB
AA
AF
AA
AA
AB
AA
AA
AC
AA
AA
AB
AB
AA
AA
AG
AL
AK
AG
AK
AG
AS
AE
AA
BE
BB
AF
AB
AU
AL
AF
AA
ELECTRIC PARTS
*
*
*
*
∆*
∆*
1- 1
1- 1
1- 2
1- 2
1- 3
1- 3
1- 4
1- 5
1- 5
1- 6
1- 7
1- 8
1- 9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-19
1-20
1-21
1-22
1-23
QSW-MA131WRE0
QSW-MA110WRE0
QSW-MA132WRE0
QSW-MA111WRE0
RMOTDA228WRE0
RMOTDA207WRE0
FH-DZA046WRK0
RC-QZA215WRE0
RC-QZA182WRE0
RMOTEA361WRE0
FPWBFA317WRK0
QACC-A071WRE0
QFS-BA007WRE0
QFS-CQ001YBE0
QTANNA017WRW0
RHET-A200WRE0
RHET-A201WRE0
RLMPUA001WRE0
RR-WZA022WRE0
RTHM-A048WRE0
RTHM-A078WRE0
RTRN-A555WRE0
RV-MZA222WRE0
RV-MZA197WRE0
FDTCTA192WRK0
FH-HZA063WRE0
RMOTEA373WRE0
QPLGAA022WRE0
1st. latch switch, 2nd. interlock relay control switch
1st. latch switch, 2nd. interlock relay control switch (Interchangeable)
Monitor switch
Monitor switch (Interchangeable)
Turntable motor
Turntable motor (Interchangeable)
High voltage rectifier assembly
High voltage capacitor
High voltage capacitor (Interchangeable)
Fan motor
Noise filter
Power supply cord
Fuse 15A
Fuse 10A
Short terminal
Grill heater (Top heater)
Bottom heater
Oven lamp (Halogen lamp)
Monitor resistor 0.8 ohm 20W
Thermal cut out 170˚C OFF / 155˚C ON
Thermal cut-out 125˚C
High voltage transformer
Magnetron
Magnetron (Interchangeable)
AH sensor assembly
Thermistor
Convection motor
AC plug
2222-
1
2
3
4
GCABDA097WRW0
GCABUA649WRP0
GDAI-A305WRW0
GLEGPA074WRE0
Back plate
Outer case cabinet
Base plate
Leg
3- 1
3- 1A
3- 1B
3- 1C
3- 1D
C1
C2
C3
C4-5
D1-4
D5-12
Q1-2
Q3
R1
R2
R3
R4
R5
R6
RY1
RY2
RY3-4
RY5
RY6
SP1
T1
VRS1
ZD1
3- 2
3- 3
3- 3-1
3- 3-2
3- 3-3
3- 4
3- 5
3- 6
CPWBFA808WRK0
QCNCMA234DRE0
QCNCMA275DRE0
FW-VZA238DRE0
QCNCMA410DRE0
RC-KZA087DRE0
VCEAB31VW108M
RC-KZA087DRE0
VCEAB31VW106M
VHD11ES1///-1
VHD1SS270A/-1
VS2SB1238//-3
VSDTD143ES/-3
VRD-B12EF242J
VRD-B12HF681J
VRD-B12HF511J
VRD-B12EF270J
VRD-B12EF472J
VRD-B12EF332J
RRLY-A080DRE0
RRLY-A081DRE0
RRLY-A076DRE0
RRLY-A080DRE0
RRLY-A076DRE0
RALM-A014DRE0
RTRNPA105DRE0
RH-VZA032DRE0
VHEHZ161///-1
DPWBFB871WRK0
DPNLCB516WRK0
JBTN-B086WRF0
MSPRCA050WRE0
FUNTKA895WRE0
LHLD-A185WRF0
PSHEPA626WRE0
XEPSD30P08XS0
Power unit
3-pin connector (CN-A)
2-pin connector (CN-B)
9pin wire harness (WH-1, WH-2)
2-pin connector (CN-D)
Capacitor
0.1 uF
50V
Capacitor
1000 uF
35V
Capacitor
0.1 uF
50V
Capacitor
10 uF
35V
Diode (11ES1)
Diode (1SS270A)
Transistor (2SB1238)
Transistor (DTD143ES)
Resistor
2.4k ohm
1/4W
Resistor
680 ohm
1/2W
Resistor
510 ohm
1/2W
Resistor
27 ohm
1/4W
Resistor
4.7k ohm
1/4W
Resistor
3.3k ohm
1/4W
Relay (OJ-SH-124LM)
Relay (VRB24)
Relay (OMIF-S-124LM)
Relay (OJ-SH-124LM)
Relay (OMIF-S-124LM)
Buzzer (PKM22EPT-THAI)
Transformer
Varistor (10G471K)
Zener diode (HZ16-1)
CPU unit
Control panel frame with key unit
Open button
Open button spring
Key unit
LCD holder
LED sheet
Screw; 3mm x 8mm
CABINET PARTS
CONTROL PANEL PARTS
42
R-880B
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
BR
AL
BF
AG
AP
AE
AN
AB
AQ
AF
AM
AF
AG
AN
AX
AM
AF
AF
AM
AF
AH
AC
AC
AG
AS
AT
AN
AF
BE
AA
AX
AC
AE
AW
AX
AX
AC
AR
AM
AK
AX
AU
AR
AQ
AQ
1
1
1
1
1
1
2
4
1
BB
AZ
AN
AF
AC
AV
AA
AA
AS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AS
AS
BC
AZ
AF
AS
AG
BB
AF
AB
AC
AC
AD
AE
14
2
AA
AA
OVEN PARTS
∆
∆
4- 1
4- 2
4- 3
4- 4
4- 5
4- 6
4- 7
4- 8
4- 9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
4-18
4-19
4-20
4-21
4-22
4-23
4-24
4-25
4-26
4-27
4-28
4-29
4-30
4-31
4-32
4-33
4-34
4-35
4-36
4-37
4-38
4-39
4-40
4-41
4-42
4-43
4-44
4-45
DOVN-A513WRY0
PHOK-A106WRF0
FDUC-A338WRK0
PCUSGA389WRP0
LANGQA478WRP0
MSPRTA186WRE0
NCPL-A051WRE0
PSPA-A109WRE0
LBNDKA136WRP0
NFANJA041WRE0
PDUC-A697WRF0
GCOVHA388WRW0
GLEGPA071WRF0
LANGFA191WRW0
LANGQA480WRP0
LFLG-A025WRE0
MLEVPA226WRF0
MSPR-A004WRE0
PCOV-A011WRP0
PCOVPA339WRE0
PCUSGA385WRP0
PCUSUA190WRP0
PCUSUA191WRP0
PDUC-A691WRF0
PDUC-A692WRP0
PDUC-A696WRP0
PGLSPA506WRE0
PCUSGA399WRE0
PREFHA061WRW0
PSHEPA487WRE0
PSKR-A358WRP0
MSPRCA113WRE0
PCUSGA420WRP0
LANGQA489WRP0
NFANMA047WRP0
NFANMA048WRP0
PCUSUA499WRP0
PDUC-A707WRW0
PFPF-A210WRE0
PPIPFA030WRE0
PSKR-A339WRP0
PSKR-A345WRW0
PSKR-A346WRW0
PSLDHA140WRW0
PCOVPA340WRW0
Oven cavity
Latch hook
Air duct assembly
Cushion
Turntable motor angle
Plate spring
Turntable motor shaft
Spacer
HV capacitor holder
Fan blade
Fan duct
Bottom heater cover
Leg
Chassis support
Lamp cover
Bearing
Switch lever
Heat seal spring
Bottom heater angle
Waveguide cover
Cushion
Cushion
Cushion
Air intake duct
Exhaust duct
Air guide
Light glass
Cushion
Reflector
Heater film
Air separate angle
H-spring
Cushion
Thermistor angle
Convection fan
Cooling fan
Cushion
Convection duct
Thermal insulation
Pipe
Convection air angle
Convection motor guide A
Convection motor guide B
Convection thermal cover
Sub back plate
1
2
3
4
5
6
7
8
9
DDORFA857WRK0
GWAKPA603WRR0
LSTPPA176WRF0
LSTPPA177WRF0
MSPRTA187WRE0
PGLSPA513WRE0
XCPSD40P06000
XCPSD40P08000
GCOVHA387WRF0
Door panel assembly
Door frame
Latch head
Glass stopper
Latch spring
Front door glass
Screw : 4mm x 6mm
Screw : 4mm x 8mm
Choke cover
6- 1
6- 2
6- 3
6- 4
6- 5
6- 6
6- 7
6- 8
6- 9
* 6-10
6-11
6-12
6-13
6-14
FAMI-A099WRM0
FAMI-A100WRM0
FSRAHA062WRY0
NTNT-A092WRH0
TLABMA584WRR0
TINSEA779WRR0
FW-VZB045WRE0
FW-VZB710WRE0
QW-QZA231WRE0
LHLDWA011WRE0
TCAUHA214WRR0
TSPCNC697WRR0
TCAUHA244WRR0
TCAUHA054WRR0
High rack
Low rack
Turntable support
Turntable
Menu label
Instruction book
Switch harness
Main wire harness
High voltage wire A
Purse lock M
K caution label
Rating label
Lamp caution
AC cord caution
DOOR PARTS
∆ 5∆ 5∆ 5555555-
MISCELLANEOUS
SCREWS,NUTS AND WASHERS
7- 1
7- 2
XFPSD40P08K00
XEPSD40P25000
Screw : 4mm x 8mm
Screw : 4mm x 25mm
43
R-880B
REF. NO.
7- 3
7- 4
7- 5
7- 6
7- 7
7- 8
7- 9
7-10
7-11
7-12
7-13
7-14
7-15
7-16
7-17
PART NO.
LX-EZA042WRE0
LX-NZ0061WRE0
XBPWW30P05K00
XCTWW40P08000
XHPSD30P06000
XHTSD40P08RV0
XOTSD40P12RV0
XOTSD40P12000
XWSUW40-10000
XOTSE40P08000
XBTSD40P05000
XNEUW40-32000
XRESE40-06000
XWHUW40-08000
XWHUW48-08120
DESCRIPTION
Special screw
Flange nut
Screw : 3mm x 5mm
Screw : 4mm x 8mm
Screw : 3mm x 6mm
Screw : 4mm x 8mm
Screw : 4mm x 12mm
Screw : 4mm x 12mm
Washer : 4mm x 1mm
Screw : 4mm x 8mm
Screw : 4mm x 5mm
Nut : 4mm x 3.2mm
Ring : 4mm x 0.6mm
Washer : 4mm x 0.8mm
Washer : 4.8mm x 0.8mm
Q'TY
2
4
2
8
3
4
15
10
1
1
2
1
1
1
1
CODE
AB
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
HOW TO ORDER REPLACEMENT PARTS
To have your order filled prompty and correctly, please furnish the following information.
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
INFORMATION FOR PARTS CHANGE
The power supply cord and AC plug will be changed as follows, and new part will be used for products from serial
number 9812xxxxx.
Interchangeability
A. OLD
NEW
B. OLD
NEW
C. OLD
REPLACEMENT PART NO.
REF.NO.
DESCRIPTION
OLD No.
Q'ty
1- 8
Power supply cord
QACC-A071WRE0
1
1-23
AC plug
QPLGAA022WRE0
1-24
Power supply cord
Not listed
NEW No.
NEW
D. OLD
NEW
InterEFFECchange- TIVE
Q'ty ability FROM CODE
-
1
Delete
Delete
-
Dec./'98
1
QACC-A104WRE0
-
-
Dec./'98
1
C
Dec./'98
NOTE: The power supply cord (Ref.: 1- 8) and AC plug (Ref.: 1-23) will be deleted and change to the new power supply
cord (Ref.: 1-24) which has the AC plug from serial number 9812xxxxx.
For old ovens (until serial number 9811xxxxx), after the power supply cord (Ref.: 1- 8) or the AC plug (Ref.:
1-23) is out of order, please use new power supply cord (Ref.: 1-24).
For new ovens (from serial number 9812xxxxx), please use new power supply cord (Ref.: 1-24).
PACKING AND ACCESSORIES
TOP PAD ASSEMBLY
TRAY HOLDER
(FPADBA381WRK0)
(SPADFA424WRE0)
TURNTABLE TRAY
WRAP COVER
HIGH RACK
LOW RACK
(SSAKHA034WRE0)
DOOR PROTECTION SHEET
(SPADPA204WRE0)
LAMP CAUTION
COOK BOOK &
INSTRUCTION BOOK
CABINET COVER
(SPAKHA009WRE0)
BOTTOM PAD ASSEMBLY
TURNTABLE SUPPORT
(FPADBA382WRK0)
TRAY PAD
(SPADPA577WRE0)
PACKING CASE
Not Replaceable Items.
44
(SPAKCD179WRE0)
R-880B
2
1
4
3
6
5
OVEN AND CABINET PARTS
A
A
2-2
7-9
6-11
7-8
4-45
7-9
4-33
2-1
B
B
7-10
4-25
7-12
4-23
1-23
4-29
4-26
7-9
7-10
7-5
6-14
7-10
6-14
7-7
1-8
4-4
4-37
4-42
1-11
7-7
C
4-15
1-14
7-4
1-20
1-12
4-30
1-16
4-31
4-34
4-27
7-15
7-13
4-3
7-10
7-10
4-40
4-43
4-32
1-8
4-18
7-13
4-24
D
1-22
1-21
7-1
4-19
7-10
C
7-17
6-5
D
4-39
7-8
4-1
4-41
1-9
1-15
7-1
7-8
1-17
7-7
7-6
4-44
4-36
1-10
7-6
4-35
7-10
1-13
4-14
7-6
4-16
6-7
7-1
7-1
E
7-6
4-6
4-20
4-18
4-32
4-19
1-7
7-6
4-21
7-14
4-41
E
7-4
4-2
1-1
6-4
1-4
1-5
7-2
4-11
1-6
4-5
1-2
1-3
7-1
4-10
4-9
4-12
1-1
7-1
7-3
F
F
4-17
7-1
6-3
7-11
7-9
4-7
4-8
7-1
4-38
7-16
1-19
1-18
4-22
7-1
4-28
G
G
2-3
7-9
2-4
2-4
7-9
H
H
4-13
7-9
1
2
4
3
45
5
6
R-880B
2
1
4
3
6
5
3-6
CONTROL PANEL PARTS
3-4
A
A
3-5
3-2
3-3
3-6
B
B
3-3-3
6-12
3-1
C
C
DOOR PARTS
3-3-1
D
5-8
3-3-2
D
5-9
5-1
E
E
5-6
5-2
5-7
F
F
5-3
5-4
MISCELLANEOUS
5-5
G
G
6-1
6-8
6-7
6-2
Actual wire harness may be different than illustration.
6-10
H
H
6-9
1
2
4
3
5
6
'98SHARP CORP. (9K0.05E) Printed in Japan
46
Download PDF