DeWalt DCD990 Instruction manual

If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-DEWALT • www.dewalt.com
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO.
DCD990 20V Max* Heavy-Duty 1/2" (13 mm) Brushless Cordless Drill/Driver
DCD995 20V Max* Heavy-Duty 1/2" (13 mm) Brushless Cordless Drill/Driver/Hammerdrill
Perceuse/visseuse industrielle, sans fil et sans balai, DCD990 20v max* 13 mm (1/2 po)
Perceuse/visseuse/perceuse à percussion industrielle, sans fil et sans balai, DCD995 20v max* 13 mm (1/2 po)
DCD990 Taladro/destornillador inalámbrico sin escobillas de 20 V Max* para trabajos pesados de 1/2" (13 mm)
DCD995 Taladro/destornillador/taladro percutor inalámbrico sin escobillas de 20 V Max* para trabajos pesados de 1/2" (13 mm)
The definitions below describe the level of severity for each signal
word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable,
use a ground fault circuit interrupter (GFCI) protected
supply. Use of a GFCI reduces the risk of electric shock.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR
ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT
(1-800-433-9258).
WARNING: To reduce the risk of injury, read the instruction
manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1
English
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Definitions: Safety Guidelines
English
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed. Use
of the power tool for operations different from those intended
could result in a hazardous situation.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energizing power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another battery
pack.
b) Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of
injury and fire.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
2
6) SERVICE
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
Drill/Driver/Hammerdrill Safety Warnings
• Wear ear protectors when impact drilling. Exposure to noise
can cause hearing loss.
• Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
• Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live” and could
give the operator an electric shock.
• Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or
against your body is unstable and may lead to loss of control.
• Wear safety goggles or other eye protection. Hammering and
drilling operations cause chips to fly. Flying particles can cause
permanent eye damage.
• Always use the side handle supplied with the tool. Keep a
firm grip on the tool at all times. Do not attempt to operate
3
English
this tool without holding it with both hands. Operating this
tool with one hand will result in loss of control. Breaking through or
encountering hard materials such as re-bar may be hazardous as
well.
• Accessories and tool may get hot during operation. Wear
gloves when handling them if performing heat producing applications
such as hammerdrilling and drilling metals.
• Do not operate this tool for long periods of time. Vibration
caused by hammer action may be harmful to your hands and arms.
Use gloves to provide extra cushion and limit exposure by taking
frequent rest periods.
• Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in moving parts.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are
NOT safety glasses. Also use face or dust mask if cutting operation is
dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains chemicals
known to the State of California to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do
this type of work. To reduce your exposure to these chemicals: work
in a well ventilated area, and work with approved safety equipment,
such as those dust masks that are specially designed to filter out
microscopic particles.
c) When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws,
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
English
• Avoid prolonged contact with dust from power sanding,
sawing, grinding, drilling, and other construction activities.
Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth, eyes, or lay on the
skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust,
which may cause serious and permanent respiratory or other
injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face
and body.
WARNING: Always wear proper personal hearing protection
that conforms to ANSI S12.6 (S3.19) during use. Under some
conditions and duration of use, noise from this product may contribute
to hearing loss.
CAUTION: When not in use, place tool on its side on a stable
surface where it will not cause a tripping or falling hazard. Some
tools with large battery packs will stand upright on the battery pack
but may be easily knocked over.
• The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ................... volts
A...................... amperes
Hz ................. hertz
W..................... watts
or AC .......... alternating
min ............... minutes
or DC ... direct current
........................ current
................. Class I Construction
or AC/DC... alternating
..................... (grounded)
........................ or direct
................. Class II Construction ........................ current
no .................... no load
..................... (double insulated)
........................ speed
…/min .......... per minute
n ...................... rated
BPM ............. beats per minute
IPM ............... impacts per minute ........................ speed
RPM ............. revolutions per
..................... minute
sfpm ............. surface feet
..................... per minute
SPM ............. strokes per minute
.................... earthing
........................ terminal
..................... safety alert
........................ symbol
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure to include the
catalog number and voltage. Consult the chart at the end of this manual
for compatibility of chargers and battery packs.
The battery pack is not fully charged out of the carton. Before using
the battery pack and charger, read the safety instructions below and
then follow charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use the battery pack in explosive
atmospheres, such as in the presence of flammable liquids,
gases or dust. Inserting or removing the battery pack from the
charger may ignite the dust or fumes.
• NEVER force the battery pack into the charger. DO NOT
modify the battery pack in any way to fit into a noncompatible charger as battery pack may rupture causing
serious personal injury. Consult the chart at the end of this
manual for compatibility of batteries and chargers.
• Charge the battery packs only in designated DEWALT chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations
where the temperature may reach or exceed 105 °F (40 °C)
(such as outside sheds or metal buildings in summer). For
best life store battery packs in a cool, dry location.
4
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling
Corporation) Seal on the nickel cadmium, nickel metal
hydride or lithium ion batteries (or battery packs)
indicate that the costs to recycle these batteries (or
battery packs) at the end of their useful life have already
been paid by DEWALT. In some areas, it is illegal to
place spent nickel cadmium, nickel metal hydride or lithium ion batteries
in the trash or municipal solid waste stream and the RBRC program
provides an environmentally conscious alternative.
RBRC™, in cooperation with DEWALT and other battery users, has
established programs in the United States and Canada to facilitate the
collection of spent nickel cadmium, nickel metal hydride or lithium ion
batteries. Help protect our environment and conserve natural resources
by returning the spent nickel cadmium, nickel metal hydride or lithium
ion batteries to an authorized DEWALT service center or to your local
retailer for recycling. You may also contact your local recycling center
for information on where to drop off the spent battery.
RBRC™ is a registered trademark of the Rechargeable Battery
Recycling Corporation.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)
• Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
lithium ion battery packs are burned.
• If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If battery
liquid gets into the eye, rinse water over the open eye for 15 minutes
or until irritation ceases. If medical attention is needed, the battery
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for battery chargers.
5
English
electrolyte is composed of a mixture of liquid organic carbonates
and lithium salts.
• Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persist, seek medical
attention.
WARNING: Burn hazard. Battery liquid may be flammable if
exposed to spark or flame.
NOTE: Do not store the battery packs in a tool with the
trigger switch locked on. Never tape the trigger switch in the
ON position.
WARNING: Fire hazard. Never attempt to open the battery pack
for any reason. If the battery pack case is cracked or damaged, do
not insert into the charger. Do not crush, drop or damage the battery
pack. Do not use a battery pack or charger that has received a sharp
blow, been dropped, run over or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped on). Damaged battery packs
should be returned to the service center for recycling.
WARNING: Fire hazard. Do not store or carry the battery pack
so that metal objects can contact exposed battery terminals.
For example, do not place the battery pack in aprons, pockets, tool
boxes, product kit boxes, drawers, etc., with loose nails, screws,
keys, etc. Transporting batteries can possibly cause fires if the
battery terminals inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the like. The US
Department of Transportation Hazardous Material Regulations (HMR)
actually prohibit transporting batteries in commerce or on airplanes
(e.g., packed in suitcases and carry-on luggage) UNLESS they are
properly protected from short circuits. So when transporting individual
battery packs, make sure that the battery terminals are protected and
well insulated from materials that could contact them and cause a
short circuit.
English
• When operating a charger outdoors, always provide a dry
location and use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric
shock.
• An extension cord must have adequate wire size (AWG or
American Wire Gauge) for safety. The smaller the gauge number
of the wire, the greater the capacity of the cable, that is, 16 gauge
has more capacity than 18 gauge. An undersized cord will cause a
drop in line voltage resulting in loss of power and overheating. When
using more than one extension to make up the total length, be sure
each individual extension contains at least the minimum wire size.
The following table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier
gauge. The lower the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
Volts
Total Length of Cord
in Feet (meters)
120 V
25
50
100
150
Ampere Rating
(7.6)
(15.2)
(30.5)
(45.7)
240 V
50
100
200
300
(15.2) (30.5)
(61.0)
(91.4)
More
Not
AWG
Than More
Than
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Recommended
• Do not place any object on top of the charger or place the
charger on a soft surface that might block the ventilation
slots and result in excessive internal heat. Place the charger
• Before using the charger, read all instructions and cautionary
markings on the charger, battery pack and product using the battery
pack.
WARNING: Shock hazard. Do not allow any liquid to get inside the
charger. Electric shock may result.
CAUTION: Burn hazard. To reduce the risk of injury, charge only
DEWALT rechargeable battery packs. Other types of batteries may
overheat and burst resulting in personal injury and property damage.
NOTICE: Under certain conditions, with the charger plugged into the
power supply, the charger can be shorted by foreign material. Foreign
materials of a conductive nature, such as, but not limited to, grinding
dust, metal chips, steel wool, aluminum foil or any buildup of metallic
particles should be kept away from the charger cavities. Always unplug
the charger from the power supply when there is no battery pack in the
cavity. Unplug the charger before attempting to clean.
• DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger and
battery pack are specifically designed to work together.
• These chargers are not intended for any uses other than
charging DEWALT rechargeable batteries. Any other uses may
result in risk of fire, electric shock or electrocution.
• Do not expose the charger to rain or snow.
• Pull by the plug rather than the cord when disconnecting the
charger. This will reduce the risk of damage to the electric plug and
cord.
• Make sure that the cord is located so that it will not be
stepped on, tripped over or otherwise subjected to damage
or stress.
• Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in risk of
fire, electric shock or electrocution.
6
•
•
•
•
Indicator Light Operation
PACK CHARGING
PACK CHARGED
HOT/COLD DELAY
x
PROBLEM POWERLINE
Charge Indicators
Chargers
This charger is designed to detect certain problems that can arise.
Problems are indicated by the red light flashing at a fast rate. If this
occurs, re-insert the battery pack into the charger. If the problem
persists, try a different battery pack to determine if the charger is
working properly. If the new pack charges correctly, then the original
pack is defective and should be returned to a service center or other
collection site for recycling. If the new battery pack elicits the same
trouble indication as the original, have the charger and the battery pack
tested at an authorized service center.
Your tool uses a DEWALT charger. Be sure to read all safety instructions
before using your charger. Consult the chart at the end of this manual
for compatibility of chargers and battery packs.
Charging Procedure
(Fig. 1)
FIG. 1
PROBLEM PACK OR CHARGER
H
1. Plug the charger into an appropriate
outlet before inserting the battery
pack.
2. Insert the battery pack (H) into
the charger, as shown in Figure 1,
making sure the pack is fully seated
in charger. The red (charging) light
will blink continuously, indicating
that the charging process has
started.
HOT/COLD DELAY
This charger has a hot/cold delay feature: when the charger detects a
battery that is hot, it automatically starts a delay, suspending charging
until the battery has cooled. After the battery has cooled, the charger
automatically switches to the pack charging mode. This feature ensures
maximum battery life. The red light flashes long, then short while in the
hot/cold delay mode.
7
English
•
•
3. The completion of charge will be indicated by the red light remaining
ON continuously. The pack is fully charged and may be used at this
time or left in the charger.
in a position away from any heat source. The charger is ventilated
through slots in the top and the bottom of the housing.
Do not operate the charger with a damaged cord or plug.
Do not operate the charger if it has received a sharp blow,
been dropped or otherwise damaged in any way. Take it to an
authorized service center.
Do not disassemble the charger; take it to an authorized
service center when service or repair is required. Incorrect
reassembly may result in a risk of electric shock, electrocution or fire.
Disconnect the charger from the outlet before attempting
any cleaning. This will reduce the risk of electric shock.
Removing the battery pack will not reduce this risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard 120V
household electrical power. Do not attempt to use it on any
other voltage. This does not apply to the vehicular charger.
English
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the charge
indicator showing Pack Charged.
4. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other
appliance;
b. Check to see if receptacle is connected to a light switch which
turns power off when you turn out the lights;
c. Move the charger and battery pack to a location where the
surrounding air temperature is approximately 65 °F – 75 °F
(18° – 24 °C);
d. If charging problems persist, take the tool, battery pack and
charger to your local service center.
5. The battery pack should be recharged when it fails to produce
sufficient power on jobs which were easily done previously.
DO NOT CONTINUE to use under these conditions. Follow the
charging procedure. You may also charge a partially used pack
whenever you desire with no adverse effect on the battery pack.
6. Foreign materials of a conductive nature such as, but not limited to,
grinding dust, metal chips, steel wool, aluminum foil, or any buildup
of metallic particles should be kept away from charger cavities.
Always unplug the charger from the power supply when there is no
battery pack in the cavity. Unplug the charger before attempting to
clean.
7. Do not freeze or immerse the charger in water or any other liquid.
WARNING: Shock hazard. Don’t allow any liquid to get inside the
charger. Electric shock may result.
WARNING: Burn hazard. Do not submerge the battery pack in
any liquid or allow any liquid to enter the battery pack. Never attempt
to open the battery pack for any reason. If the plastic housing of the
battery pack breaks or cracks, return to a service center for recycling.
WEAK BATTERY PACKS: Weak batteries will continue to function but
should not be expected to perform as much work.
FAULTY BATTERY PACKS: This charger will not charge a faulty
battery pack. The charger will indicate faulty battery pack by refusing to
light or by displaying problem pack or charger.
NOTE: This could also mean a problem with a charger.
PROBLEM POWER LINE
Some chargers have a Problem Power Line indicator. When the charger
is used with some portable power sources such as generators or
sources that convert DC to AC, the charger may temporarily suspend
operation, flashing the red light with two fast blinks followed by a pause.
This indicates the power source is out of limits.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery
pack is charged when the air temperature is between 65 °F and
75 °F (18° – 24 °C). DO NOT charge the battery pack in an air
temperature below +40 °F (+4.5 °C), or above +105 °F (+40.5 °C).
This is important and will prevent serious damage to the battery
pack.
2. The charger and battery pack may become warm to the touch
while charging. This is a normal condition, and does not indicate
a problem. To facilitate the cooling of the battery pack after use,
avoid placing the charger or battery pack in a warm environment
such as in a metal shed or an uninsulated trailer.
3. A cold battery pack will charge at about half the rate of a warm
battery pack. The battery pack will charge at that slower rate
throughout the entire charging cycle and will not return to maximum
charge rate even if the battery pack warms.
Storage Recommendations
1. The best storage place is one that is cool and dry, away from direct
sunlight and excess heat or cold.
8
2. For long storage, it is recommended to store a fully charged battery
pack in a cool dry place out of the charger for optimal results.
NOTE: Battery packs should not be stored completely depleted of
charge. The battery pack will need to be recharged before use.
COMPONENTS (FIG. 2)
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
FIG. 2
E
D
F
Variable Speed Trigger Switch (Fig. 2)
To turn the tool on, squeeze the trigger switch (A). To turn the tool
off, release the trigger switch. Your tool is equipped with a brake. The
chuck will stop as soon as the trigger switch is fully released.
NOTE: Continuous use in variable speed range is not recommended.
It may damage the switch and should be avoided.
DCD995
B
Side Handle (Fig. 2)
A
WARNING: To reduce the risk of personal injury, ALWAYS operate
the tool with the side handle properly installed. Failure to do so may
result in the side handle slipping during tool operation and subsequent
loss of control. Hold tool with both hands to maximize control.
Side handle (G) clamps to the front of the gear case and may be rotated
360° to permit right- or left-hand use. Side handle must be tightened
sufficiently to resist the twisting action of the tool if the accessory binds
or stalls. Be sure to grip the side handle at the far end to control the tool
during a stall.
If model is not equipped with side handle, grip drill with one hand on the
handle and one hand on the battery pack.
NOTE: Side handle comes equipped on both models.
C
G
I
K
L
J
H
9
English
WARNING: Never modify the power tool or any part of it. Damage
or personal injury could result.
A. Trigger switch
G. Side handle
B. Forward/reverse control button
H. Battery pack
C. Worklight
I. Battery release button
D. Chuck
J. Belt hook
E. Torque adjustment collar
K. Bit clip
F. Gear shifter
L. Screw
English
Forward/Reverse Control Button (Fig. 2)
WARNING: When the torque adjustment collar is in the drill or
hammerdrill positions, the drill will not clutch. The drill may stall if
overloaded, causing a sudden twist.
A forward/reverse control button (B) determines the direction of the
tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and depress the
forward/reverse control button on the right side of the tool.
To select reverse, release the trigger switch and depress the forward/
reverse control button on the left side of the tool.
The center position of the control button locks the tool in the OFF
position. When changing the position of the control button, be sure
the trigger is released.
NOTE: The first time the tool is run after changing the direction of
rotation, you may hear a click on start up. This is normal and does not
indicate a problem.
FIG. 3
FIG. 4
FIG. 5
E
E
F
F
Worklight (Fig. 2)
There is a worklight (C) located on the foot of the tool. The worklight is
activated when the trigger switch is depressed, and will automatically
turn off 20 seconds after the trigger switch is released. If the trigger
switch remains depressed, the worklight will remain on.
NOTE: The worklight is for lighting the immediate work surface and is
not intended to be used as a flashlight.
Three-Speed Gearing (Fig. 3–5)
The three-speed feature of your tool allows you to shift gears for greater
versatility. To select speed 1 (highest torque setting), turn the tool off and
permit it to stop. Slide the gear shifter (F) all the way forward. Speed 2
(middle torque and speed setting) is in the middle position. Speed 3
(highest speed setting) is to the rear.
NOTE: Do not change gears when the tool is running. Always allow
the drill to come to a complete stop before changing gears. If you have
trouble changing gears, depress and release the trigger switch and try
again.
Torque Adjustment Collar/Electronic
Clutch (Fig. 3–5)
Your tool has an electronic adjustable torque screwdriver system for
driving and removing a wide array of fasteners. Circling the torque
adjustment collar (E) are numbers. These numbers are used to set the
clutch to deliver a torque range. The higher the number on the collar,
the higher the torque and the larger the fastener that can be driven. To
select any of the numbers, rotate until the desired number aligns with
the arrow.
Keyless Single Sleeve Chuck (Fig. 6–8)
WARNING: Do not attempt to tighten drill bits (or any other
accessory) by gripping the front part of the chuck and turning the
10
tool on. Damage to the chuck and personal injury may result. Always
lock off trigger switch and disconnect tool from power source when
changing accessories.
WARNING: Always ensure the bit is secure before starting the
tool. A loose bit may eject from tool causing possible personal injury.
Your tool features a keyless chuck with one rotating sleeve for onehanded operation of the chuck. To insert a drill bit or other accessory,
follow these steps.
WARNING: To reduce the risk of serious personal injury, DO
NOT suspend tool overhead or suspend objects from the belt hook.
ONLY hang tool’s belt hook from a work belt.
WARNING: To reduce the risk of serious personal injury,
ensure the screw holding the belt hook is secure.
IMPORTANT: When attaching or replacing the belt hook (J) or bit clip
(K), use only the screw (L) that is provided. Be sure to securely tighten
the screw.
The belt hook (J) and bit clip (K) can be be attached to either side of
the tool using only the screw (L) provided, to accommodate left- or
right- handed users. If the hook or bit clip is not desired at all, it can be
removed from the tool.
To move belt hook or bit clip, remove the screw (L) that holds it in place
then reassemble on the opposite side. Be sure to securely tighten the
screw.
FIG. 8
D
OPERATION
WARNING: To reduce the risk of serious personal injury, place
the forward/reverse button in the lock-off position or turn tool
off and disconnect battery pack before making any adjustments
or removing/installing attachments or accessories. An accidental
start-up can cause injury.
1. Turn tool off and disconnect tool from power source.
2. Grasp the black sleeve of the chuck (D) with one hand and use
the other hand to secure the tool as shown in Figure 6. Rotate the
sleeve counterclockwise (as viewed from the front) far enough to
accept the desired accessory.
3. Insert the accessory about 3/4" (19 mm) into the chuck and tighten
securely by rotating the chuck sleeve clockwise with one hand
while holding the tool with the other hand. Continue to rotate the
chuck sleeve until several ratchet clicks are heard to ensure full
gripping power.
Be sure to tighten chuck with one hand on the chuck sleeve and one
hand holding the tool for maximum tightness.
To release the accessory, repeat Steps 1 and 2 above.
Installing and Removing the Battery Pack
(Fig. 9)
NOTE: For best results, make sure your battery pack is fully charged.
To install the battery pack (H) into the tool handle, align the battery
pack with the rails inside the tool’s handle and slide it into the handle
until the battery pack is firmly seated in the tool and ensure that it does
not disengage.
11
English
FIG. 7
FIG. 6
Belt Hook and Bit Clip (Fig. 2)
NOTE: The fuel gauge is only an indication of the charge left on the
battery pack. It does not indicate tool functionality and is subject to
variation based on product components, temperature and end-user
application.
For more information regarding fuel gauge battery packs, please call
1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.
com.
English
To remove the battery pack from the tool, press the release button (I)
and firmly pull the battery pack out of the tool handle. Insert it into the
charger as described in the charger section of this manual.
FIG. 9
Screwdriving (Fig. 3)
I
1. Select the desired speed/torque range using the gear shifter to
match the speed and torque to the planned operation.
2. Turn the torque adjustment collar (E) to the desired position.
NOTE: Use the lowest torque setting required to seat the fastener
at the desired depth. The lower the number, the lower the torque
output.
3. Insert the desired fastener accessory into the chuck as you would
any drill bit.
4. Make some practice runs in scrap or on unseen areas of the
workpiece to determine the proper position of the torque
adjustment collar.
5. Always start with lower torque settings, then advance to higher
torque settings to avoid damage to the workpiece or fastener.
NOTE: When torque is achieved in screwdriving mode, the unit will
automatically shut off with a set of short pulses.
H
FUEL GAUGE BATTERY PACKS (FIG. 10)
Some DEWALT battery packs include a fuel gauge which consists of
three green LED lights that indicate the level of charge remaining in the
battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button (M). A
combination of the three green LED lights will illuminate designating the
level of charge left. When the level of charge in the battery is below the
usable limit, the fuel gauge will not illuminate and the battery will need
to be recharged.
FIG. 10
Drilling (Fig. 4)
M
NOTICE: If drilling thin material, use a wood “back-up” block to
prevent damage to the material.
1. Select the desired speed/torque range using the gear shifter to
match the speed and torque to the planned operation. Turn the
collar (E) to the drill symbol.
12
3. Drill straight, keeping the bit at a right angle to the work. Do not
exert side pressure on the bit when drillling as this will cause
clogging of the bit flutes and a slower drilling speed.
4. When drilling deep holes, if the hammer speed starts to drop off,
pull the bit partially out of the hole with tool still running to help clear
debris from the hole.
NOTE: A smooth, even flow of dust from the hole indicates proper
drilling rate.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, place
the forward/reverse button in the lock-off position or turn tool
off and disconnect battery pack before making any adjustments
or removing/installing attachments or accessories. An accidental
start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air
at least once a week. To minimize the risk of eye injury, always wear
ANSI Z87.1 approved eye protection when performing this.
WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals may
weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.
Hammerdrilling (Fig. 5)
1. Select the desired speed/torque range using the gear shifter to
match the speed and torque to the planned operation. Turn the
collar (E) to the hammerdrill symbol.
IMPORTANT: Use carbide-tipped or masonry bits rated for
percussion drilling only.
2. Drill with just enough force on the hammer to keep it from bouncing
excessively or "rising" off the bit. Too much force will cause slower
drilling speeds, overheating, and a lower drilling rate.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC
outlet before cleaning. Dirt and grease may be removed from the
exterior of the charger using a cloth or soft non-metallic brush. Do not
use water or any cleaning solutions.
13
English
2. Use sharp drill bits only. For MASONRY, such as brick, cement,
cinder block, etc., use carbide-tipped bits rated for percussion
drilling.
3. Always apply pressure in a straight line with the bit. Use enough
pressure to keep drill biting, but do not push hard enough to stall
the motor or deflect the bit.
4. Hold tool firmly with both hands to control the twisting action of the
drill. If model is not equipped with side handle, grip drill with one
hand on the handle and one hand on the battery pack.
WARNING: Drill may stall if overloaded causing a sudden twist.
Always expect the stall. Grip the drill firmly to control the twisting
action and avoid injury.
5. IF DRILL STALLS, it is usually because it is being overloaded
or improperly used. RELEASE TRIGGER IMMEDIATELY,
remove drill bit from work, and determine cause of stalling. DO
NOT DEPRESS TRIGGER ON AND OFF IN AN ATTEMPT
TO START A STALLED DRILL — THIS CAN DAMAGE THE
DRILL.
6. To minimize stalling or breaking through the material, reduce
pressure on drill and ease the bit through the last fractional part of
the hole.
7. Keep the motor running when pulling the bit back out of a drilled
hole. This will help prevent jamming.
English
Accessories
Repairs
WARNING: Since accessories, other than those offered by
DEWALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the risk of
injury, only DEWALT recommended accessories should be used with
this product.
Recommended accessories for use with your tool are available at
extra cost from your local service center. If you need any assistance
in locating any accessory, please contact DEWALT Industrial Tool Co.,
701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT
(1-800-433-9258) or visit our website: www.dewalt.com.
The charger and battery pack are not serviceable. There are no
serviceable parts inside the charger or battery pack.
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustments should be performed by a DEWALT factory service
center, a DEWALT authorized service center or other qualified service
personnel. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will help you
obtain more efficient warranty service in case there is a problem
with your product.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss,
such as fire, flood or theft, your registration of ownership will serve
as your proof of purchase.
• FOR YOUR SAFETY: Registering your product will allow us to
contact you in the unlikely event a safety notification is required
under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
MAXIMUM RECOMMENDED CAPACITIES
DCD990
DCD995
Auger
1-1/4" (32 mm)
1-1/4" (32 mm)
Paddle
1-1/2" (38 mm)
1-1/2" (38 mm)
1/2" (13 mm)
1/2" (13 mm)
Self-feed
2-9/16" (65 mm)
2-9/16" (65 mm)
Hole saw
4" (100 mm)
4" (100 mm)
1/2" (13 mm)
1/2" (13 mm)
1-3/8" (35 mm)
1-3/8" (35 mm)
–
1/2" (13 mm)
WOOD
Twist
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials
or workmanship for three years from the date of purchase. This warranty
does not cover part failure due to normal wear or tool abuse. For further
detail of warranty coverage and warranty repair information, visit www.
dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty
does not apply to accessories or damage caused where repairs have
been made or attempted by others. This warranty gives you specific
legal rights and you may have other rights which vary in certain states
or provinces.
METAL
Twist
Hole saw
MASONRY
Carbide
14
FREE WARNING LABEL REPLACEMENT: If your warning labels
become illegible or are missing, call 1-800-4-DEWALT (1-800-4339258) for a free replacement.
In addition to the warranty, DEWALT tools are covered by our:
English
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by
normal use, for free, any time during the first year after purchase.
2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS
DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120,
DCB201 and DCB203
3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS
DCB200, DCB204
DEWALT BATTERY PACKS
Product warranty voided if the battery pack is tampered with in any
way. DEWALT is not responsible for any injury caused by tampering and
may prosecute warranty fraud to the fullest extent permitted by law.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your DEWALT
Power Tool, Laser, or Nailer for any reason, you can return it within 90
days from the date of purchase with a receipt for a full refund – no
questions asked.
LATIN AMERICA: This warranty does not apply to products sold in
Latin America. For products sold in Latin America, see country specific
warranty information contained in the packaging, call the local company
or see website for warranty information.
15
DEWALT Battery and Charger Systems
Battery
Output
Chargers/Charge Time (Minutes) – Chargeurs/Durée de charge (Minutes) – Cargadores de baterías/Tiempo de carga (Minutos)
120 Volts
Cat #
DC9360
DC9280
DW0242
DC9096
DC9099
DC9180
DC9181
DCB080
DCB200
DCB201
DCB203
DCB204
DCB207
DW9096
DW9098
DW9099
DC9091
DC9094
DW9091
DW9094
DCB120
DC9071
DW9050
DW9071
DW9072
DW9048
DW9061
DW9062
DW9057
Voltage
36
28
24
18
18
18
18
8
20
20
20
20
20
18
18
18
14.4
14.4
14.4
14.4
12
12
12
12
12
9.6
9.6
9.6
7.2
DW9106
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
90
60
60
45
X
90
40
60
45
40
60
45
45
DW9118
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
115
90
90
60
X
115
X
90
60
X
90
60
60
DW9107
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
60
45
45
30
X
60
X
45
30
X
45
30
30
DW9108
X
X
X
60
45
X
X
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
DW9116
X
X
X
60
45
X
X
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
DW9216
X
X
X
60
45
X
X
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
DW9117
X
X
X
20
15
X
X
X
X
X
X
X
X
20
12
15
20
15
15
12
X
20
X
15
12
X
15
12
12
DW911
X
X
X
60
45
X
X
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
DC011
X
X
X
60
45
X
X
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
12 Volts
DC022
X
X
X
60
45
X
X
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
DC9000
60
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DC9310
X
X
X
60
45
60
30
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
DC9320
X
X
X
60
45
60
30
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
DCB095
X
X
X
X
X
X
X
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DCB100
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
40
X
X
X
X
X
X
X
X
DCB101
X
X
X
X
X
X
X
X
60
30
40
80
30
X
X
X
X
X
X
X
30
X
X
X
X
X
X
X
X
DCB103
X
X
X
60
45
60
30
X
60
30
40
80
30
60
30
45
60
45
45
30
30
60
X
45
30
X
45
30
30
DCB106
X
X
X
X
X
X
X
X
140
70
90
185
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DW0246
X
X
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DCB119
X
X
X
X
X
X
X
X
90
45
60
120
X
X
X
X
X
X
X
X
40
X
X
X
X
X
X
X
X
DW0249
X
X
60
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DW9109
X
X
X
60
45
X
X
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
DC9319
X
X
X
60
45
60
30
X
X
X
X
X
X
60
30
45
60
45
45
30
X
60
X
45
30
X
45
30
30
“X” Indicates that the battery pack is not compatible with that specific charger.
“X” indique que le bloc-piles n’est pas compatible avec ce chargeur.
Una “X” indica que el paquete de baterías no es compatible con ese determinado cargador.
All charge times are approximate. Actual charge time may vary. Read the instruction manual for more specific information.
Les durées de charge sont approximatives; la durée de charge rélle peut varier. Lire le manuel d’utilisation pour obtenir des renseignements plus précis.
El tiempo de duración de carga es aproximado; la duración de carga real puede variar. Lea el manual de instrucciones para obtener información más precisa.
* Maximum initial battery voltage (measured without a workload) is 20 volts. Nominal voltage is 18.
* La tension initiale maximum du bloc-piles (mesurée à vide) est de 20 volts. La tension nominale est de 18.
* El máximo voltaje inicial de la batería (medido sin carga de trabajo) es 20 voltios. El voltaje nominal es de 18.
DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286
(JUL13)
Part No. N257740
DCD990, DCD995
Copyright © 2013 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array
of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.