SINGLE OVEN DUAL FUEL RANGE VCLFSGE 365 ..

SINGLE OVEN DUAL FUEL RANGE VCLFSGE 365 ..
SINGLE OVEN DUAL FUEL RANGE
R
Models:
VCLFSGE 365 ..
INSTALLATION INSTRUCTIONS
IMPORTANT - PLEASE READ AND FOLLOW
•
•
•
•
•
Before beginning, please read these instructions completely and carefully.
Do not remove permanently affixed labels, warnings, or plates from the product. This may
void the warranty.
Please observe all local and national codes and ordinances.
Please ensure that this product is properly grounded.
The installer should leave these instructions with the consumer who should retain
for local inspector’s use and for future reference.
Installation must conform with local codes or in the absence of codes, the National Fuel Gas
Code ANSI Z223.1/NFPA 54 - Iatest edition. Electrical installation must be in accordance
with the National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes.
IN CANADA: Installation must be in accordance with the current CAN/CGA-B149.1 National
Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.
Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical
Codes Part 1 and/or local codes.
INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform
with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280
[formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD
(Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.
INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with
state or other codes or, in the absence of such codes, with the Standard for Recreational
Park Trailers, ANSI A119.5.
Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual
shut-off valve must be installed in an accessible location in the gas line external to the
appliance for the purpose of turning on or shutting off gas to the appliance (In Massachusetts
such shutoff devices should be approved by the Board of State Examiners of Plumbers &
Gas Fitters).
If an external electrical source is utilized, the appliance, when installed, must be electrically
grounded in accordance with local codes or, in the absence of local codes, with the national
Electrical Code, ANSI/NFPA 70.
Some models are supplied with a protective film on steel and aluminium
parts. This film must be removed before installing/using the appliance.
FOR INSTALLER ONLY
THIS RANGE IS FOR RESIDENTIAL USE ONLY
WARNING !
To reduce the risk of tipping the appliance,
the appliance must be secured by properly
installed anti-tip device packed with the
appliance.
• ALL RANGES CAN TIP
• INJURY TO PERSONS COULD RESULT
• INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE
• SEE INSTALLATION INSTRUCTIONS
WARNING !
If the information in this manual is not followed exactly,
a fire or explosion may result causing property damage,
personal injury, or death.
–– Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
–– NEVER use this appliance as a space heater to heat or
warm the room. Doing so may result in carbon monoxide
poisoning and overheating of the appliance.
–– WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• lmmediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• lf you cannot reach your gas supplier, call the fire
department.
–– Installation and service must be performed by a qualified
installer, service agency, or the gas supplier.
2
DATA PLATE
CONVERSION LABEL
The Governor of California is required to publish a list of substances known to the state of California
to cause cancer or reproductive harm and requires businesses to warn customers of potential
exposures to such substances.
WARNING!: Gas appliances contain or produce substances which can cause death or serious illness
and which are known to the State of California to cause cancer, birth defects or other reproductive
harm. To reduce the risk from substances in fuel or from fuel combustion, make sure this appliance
is installed, operated, and maintained according to the manufacturer’s instructions.
This appliance is designed and manufactured solely for the cooking of domestic (household)
food and in not suitable for any none domestic application and therefore should not be used in a
commercial environmement.
The appliance warranty will be void if the appliance is used within a none domestic environmement
i.e. a semi commercial, commercial or communal environment.
3
INSTALLATION INSTRUCTIONS
WARNING!
THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER.
Installation must conform with local codes.
Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a
qualified installer, service agente or the gas supplier.
IMPORTANT: The use of suitable protective clothing/gloves is
recommended when handling, installing of this appliance.
TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE)
4
Screwdriver
2 - Wrench
Suitable protective
gloves
Hammer
T-handle
wrench
Pencil
Adjustable
wrench
Adjustable
pliers
Tape
measure
Drill
GENERAL INFORMATION
1. Installation must conform with local codes or, in the absence
of local codes, with the National Fuel Gas Code, ANSI
Z223.1/NFPA 54 - Latest Edition, CAN/CGA-B149.1 or CAN/
CGA-B149.2.
2. Installation in manufactured (mobile) home: installation must
conform with the Manufactured Home Construction and
Safety Standard, Title 24 CFR, Part 3280 [formerly the
Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD (Part 280)] or, when such standard
is not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or with local codes
where applicable.
3. Installation in Recreational Park Trailers: installation must
conform with state or other codes or, in the absence of such
codes, with the Standard for Recreational Park Trailers,
ANSI A119.5.
4. To eliminate risk of burns or fire by reaching over heated
surface units, cabinet storage located above the surface units
should be avoided.
5. Air curtain or other overhead range hoods, which operate
by blowing a downward air flow on to a range, shall not be
used in conjunction with gas ranges other than when the
hood and range have been designed, tested and listed by an
independent test laboratory for use in combination.
WARNING!!
ELECTRICAL GROUNDING INSTRUCTIONS
The range must be electrically grounded in accordance with
local codes or, in the absence of local codes, with the National
Electrical Code, ANSI/NFPA No. 70-latest edition, in Canada
Canadian Electrical Code.
Installation should be made by a Iicensed electrician.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
If an external electrical source is utilized, the installation must be
electrically grounded in accordance with local codes or, in the
absence of local codes, with the national Electrical Code, ANSI/
NFPA 70.
WARNING!!
6.
16. When installing or removing the range for service, a rolling lift
jack should be used. Do not push against any of the edges of
the range in an attempt to slide it into or out of the installation.
Pushing or pulling a range (rather than using a lift jack) also
increases the possibility of bending the leg spindles or the
internal coupling connectors.
This appliance shall not be used for space heating. This
information is based on safety considerations.
7. AlI openings in the wall behind the appliance and in the floor
under the appliance shall be sealed.
8. Keep appliance area clear and free from combustible
materials, gasoline, and other flammable vapors.
9. Do not obstruct the flow of combustion and ventilation air.
REPLACEMENT PARTS
Only authorized replacement parts may be used in performing
service on the range. Replacement parts are available from factory
authorized parts distributors. Contact the nearest parts distributor
in your area.
10. Disconnect the electrical supply to the appliance before
servicing.
11. When removing appliance for cleaning and/or service;
A. Shut off gas at main supply.
B. Disconnect AC power supply.
C. Disconnect gas line to the inlet pipe.
D. Carefully remove the range by pulling outward.
CAUTION: Range is heavy; use care in handling.
12. Electrical Requirement
Electrical installation should comply with national and local
codes.
13. Air Supply and Ventilation
The installer must refers to local/national codes.
14. Gas Manifold Pressure
Natural gas - 4.0” W.C.P.
LP/Propane - 11.0” W.C.P.
15. The misuse of oven door (e.g. stepping, sitting, or leaning on
them) can result in potential hazards and/or injuries.
5
installation
1
PROXIMITY TO SIDE CABINETS
1. This range may be installed directly adjacent to existing 36”
(914 mm) high base cabinets.
Range dimensions:
• width: 35” 7/8 (911 mm)
• depth: 23” 31/32 (609 mm)
• height (without backguard / island trim): MIN 35” 7/16
(900 mm) MAX 35” 5/8 (905 mm)
• backguard (height): 8” (203 mm)
• island trim (height): 3” (76 mm)
Gas line opening:
Wall - 7” 15/32 (190 mm) from the floor; 17” 15/16 (455.5 mm)
from the rear left side to centre of the range.
Grounded outlet: Grounded outlet should be located 17”
15/16 (455.5 mm) from the right side to centre of range and
from 6” 11/16 (170 mm) to 6” 57/64 (175 mm) [depending on
feet regulation] from the floor.
2. The range CANNOT be installed directly adjacent to sidewalls,
tall cabinets, tall appliances, or other side vertical surfaces
above 36” (914 mm) high.
There must be a minimum of 11” 13/16 (300 mm) side
clearance from the range to such combustible surfaces TO
THE LEFT or TO THE RIGHT above the 36” (914 mm) high
countertop.
IMPORTANT: One side (left or right) above the 36” (914
mm) high countertop must always be kept clear.
Installation with island trim: There must be a minimum of 12”
(305 mm) clearance from the back of the island trim to such
combustible surface on the back of the range above the 36”
(914 mm) high countertop.
3. The maximum upper cabinet depth recommended is 13” (330
mm). Wall cabinet above the range must be a minimum of 30”
(762 mm) above the countertop for a width of minimum 35”
7/8 (911 mm): it has to be centred with the range. Side wall
cabinets above the range must be a minimum of 18” (457 mm)
above the countertop.
(76 mm)
3"
MIN 35" 7/16 (900 mm)
23"
(60 31/32
9m
m)
MAX 35" 5/8 (905 mm)
(203 mm)
Island trim
23"
(60 31/32
9m
m)
MAX 35" 5/8 (905 mm)
MIN 35" 7/16 (900 mm)
8"
Backguard
7/8
7/8
35"
)
mm
(911
35"
)
mm
(911
Fig. 1.1a
6
Fig. 1.1b
1
GAS AND ELECTRIC CONNECTION
Rif.
inch
mm
A
7” 15/32
190
B
17” 15/16
455.5
C
6” 11/16 ÷ 6” 57/64 (*)
170 ÷ 175 (*)
D
17” 15/16
455.5
* : Depending on feet regulation
Dotted line showing the position
of the range when installed
Area for GAS connection
B
Area for ELECTRICAL
connection
D
A
C
Fig. 1.2
7
1
PROXIMITY TO SIDE CABINETS
13" max.
(330 mm)
min. (300
mm)
30" min.
(762 mm)
11" 13/16
18" min.
(457 mm)
RANGE WITH BACKGUARD
20" min
. (500 m
36"
(914 mm)
m)
Fig. 1.3a
0"
(0 mm
)
0"
(0 mm
13" max. (3
)
30 mm)
18" min.
(457 mm)
30" min.
(762 mm)
OVEN
11" 13/16
min. (300
mm)
)
500 mm
OVE
N VE
36"
(914 mm)
.(
20" min
0"
m)
(0 m
0"
)
(0 mm
8
Fig. 1.3b
NT
VENT
1
13" max. (3
30 mm)
PROXIMITY TO SIDE
CABINETS
min
. (30
5m
m)
18" min.
(457 mm)
12"
30" min.
(762 mm)
RANGE WITH ISLAND TRIM
)
. (300 mm
min
11" 13/16
m)
. (500 m
36"
(914 mm)
20" min
Fig. 1.3c
0"
m)
(0 m
0"
)
(0 mm
(330 mm)
11" 13/16
min. (300
mm)
30" min.
(762 mm)
VENT
18" min.
(457 mm)
12"
305
in. (
)
mm
m
20" min
. (500 m
N
OVE
T
VEN
m)
36"
(914 mm)
OVEN
13" max.
0"
(0 mm
)
0"
(0 mm
)
Fig. 1.3d
9
1
Fig. 1.4
Fig. 1.5
FITTING THE ADJUSTABLE FEET
The adjustable feet must be fitted to the base of the cooker before use.
Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base
for the fitting of the feet.
ATTENTION: Most important! Pay special attention not to damage the range
during this operation.
Fit the 4 legs by screwing them tight into the support base as shown in picture 1.5.
LEVELLING THE COOKER
Fig. 1.6
The cooker may be levelled by screwing the lower ends of the feet IN or OUT (fig. 1.6).
It is important to observe the directions of figure 1.6.
MOVING THE COOKER
WARNING
When raising cooker to upright position always ensure two people carry out this
manoeuvre to prevent damage to the adjustable feet (fig. 1.7a).
WARNING
Be careful: do not lift the cooker by the door handle when raising to the upright
position (fig. 1.7b).
WARNING
When moving cooker to its final position DO NOT DRAG (fig. 1.7c).
Lift feet clear of floor (fig. 1.7a).
Fig. 1.7a
10
Fig. 1.7b
Fig. 1.7c
1
IMPORTANT: THE BACKGUARD OR ISLAND TRIM IS NOT PACKAGED
WITH THE APPLIANCE BUT IT IS SUPPLIED SEPARATELY BY THE
DISTRIBUTOR.
WITH RESPECT TO THE FIGURES BELOW, ONE ADDITIONAL
BACKGUARD (HEIGHT = 4”) OR ISLAND TRIM (HEIGHT = 2”) IS ALSO
AVAILABLE FOR RANGE DEPTH = 25” ½.
IT IS MANDATORY TO INSTALL THE BACKGUARD OR
ISLAND TRIM.
B
ASSEMBLING THE BACKGUARD
OR THE ISLAND TRIM
It is mandatory to install the backguard or the
island trim
• Assemble the backguard or the island trim
as shown in figure 1.8 or 1.9 and fix it
by screwing the 5 screws “A” (which are
already fixed on the back of the cooktop).
• Do not remove the 3 spacers “B” already
fitted on the back of the backguard or island
trim.
A
A
B
Fig. 1.8
B
A
A
B
Fig. 1.9
11
1
YOU
MUST
USE
STABILITY ANTI TIP
BRACKET TO PREVENT
UNIT FROM TIPPING.
ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS
1. The anti-tip bracket has to be attached as shown on figure below, it has to be fixed
on the rear wall by no. 2 (two) suitable screws (supplied with the anti-tip kit).
2. After fixing the anti-tip bracket, slide range into place. Be sure the anti-tip bracket is
fully inserted in the slot of the range back.
Dotted line showing the position
of the range when installed
from top of cooktop
with range installed
in final position
ANTI-TIP STABILITY
DEVICE FIXING
26" 11/16 (678 mm)
17" 15/16
(455.5 mm)
17" 15/16
(455.5 mm)
Anti-tip
stability device
Slot for inserting
the anti-tip bracket
Fig. 1.10
12
gas connection
2
All gas connections must be made according to national and local codes. This gas
supply (service) line must be the same size or greater than the inlet line of the
appliance. Sealant on all pipe joints must be resistant to te action of LP/Propane gas.
The range is equipped for the use with NATURAL gas. It is design-certified by CSA
International for NATURAL and L.P. gases with appropriate conversion.
The model/serial rating plate, located on the inner side of the storage compartment
pivoting panel, has information on the type of gas that can be used. If this information
does not agree with the type of gas available, check with the local gas supplier. See
page from 19 to 21 for L.P. gas conversion inctructions.
1. Manual Shut-off Valve
(fig. 2.1):
A manual shut-off valve must be installed in an accessible location in the gas line
external to the appliance for the purpose of turning on or shutting off gas to the
appliance (In Massachusetts such shutoff devices should be approved by the Board
of State Examiners of Plumbers & Gas Fitters). This valve should be located in the
same room as the range and should be in a location that allows ease of opening and
closing (in a position where it can be reached quickly in the event of an emergency).
Do not block access to the shutoff valve. The valve is for turning on or shutting off
gas to the appliance.
Explosion Hazard
Use a new CSA or UL approved
gas supply line.
Install a shut-off valve.
Securely tighten
connections.
all
gas
If connected to LP, have a
qualified person make sure gas
pressure does not exceed 14”
water column.
Examples of a qualified
person
include
licensed
heating personnel, authorized
gas company personnel, and
authorized service personnel.
Failure to do so can result in
death, explosion, or fire.
Shutoff valve
“open” position
To range
Gas supply line
Fig. 2.1
2. Pressure Regulator:
a) A
ll heavy duty, commercial type cooking equipment must have a pressure regulator
on the incoming service line for safe and efficient operation, since service pressure
may fluctuate with local demand.
Before installing the regulator mount the 1/2” NPT (conical) male connector to the
regulator (see picture 2.2a). Gasket supplied have to be placed between 1/2” NPT
(conical) connector/extension pipe male pipe fitting (see picture 2.2b).
The regulator supplied with this range must be installed before any gas connections
are made.
Use supplied pressure regulator only. b)Assemble the extension pipe + pressure regulator group to the range manifold
interposing the gasket supplied.
13
2
PRESSURE REGULATOR INSTALLATION
STEP 1
Mount the 1/2” NPT (conical) male connector to the pressure
regulator and tighten by using a wrench.
Do not over tighten the connector.
Over tightening may crack regulator.
LOCK
Arrow
Fig. 2.2a
STEP 2
Assemble the 1/2” NPT connector + pressure regulator group to the
extension pipe interposing the gasket supplied. The regulator cover must
be ordiented toward the front side of the range.
IMPORTANT: use two spanners to tighten the connection.
Regulator
cover
Fig. 2.2b
14
2
STEP 3
Insert the extension pipe + pressure regulator
group in the “A” bracket.
A
A
Fig. 2.2c
STEP 4
Assemble the extension pipe + pressure
regulator group to the range manifold
interposing the gasket supplied. The
regulator cover must be ordiented toward
the front side of the range.
IMPORTANT: use two spanners to
tighten the connection.
Fig. 2.2d
15
2
STEP 5
Fix the “B” bracket on the back of the range by the 2 (two) screws
supplied with the kit for gas connection.
The regulator cover must be ordiented toward the front side of
the range. B
B
Fig. 2.2e
16
2
GAS CONNECTION SPECIFICATION
To range
Range
manifold
Manifold male
pipe fitting
1/2” G cylindrical
(ISO 228-1) male
Gasket
1/2” G cylindrical
(ISO 228-1) female
Extension
Extension
pipe
pipe female
female
pipe
pipe fitting
fitting
To mains
connection
Extension
pipe
Pressure
regulator
Gasket
1/2” NPT
female
1/2” NPT
(conical)
male
Extension
pipe male
pipe fitting
1/2” NPT
female
Arrow
Connector
1/2” G cylindrical
(ISO 228-1) male
1/2” G cylindrical
(ISO 228-1) female
WARNING: check the right
positioning of the gas regulator.
The arrow on the gas regulator must
be oriented toward the connector.
Fig. 2.3
17
2
TEST POINT ADAPTER
The Test Point adapter is available from
the After-Sales Service.
c) Any conversion required must be performed by your dealer or a qualified licensed
plumber or gas service company. Please provide the service person with this
manual before work is started on the range. (Gas conversions are the responsibility
of the dealer or end user.)
d) This range can be used with NATURAL or LP/PROPANE gas. It is shipped from
the factory adjusted for use with NATURAL gas.
e) Manifold pressure should be checked with a manometer and by operating as
below detailed:
- Remove the injector from the front left burner and mount the proper test point
adapter which is available from the After-Sales Service (see side figure and the
“OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE INJECTORS”
chapter).
- Turn the front left burner control knob to the maximum position (
position)
- Press the knob and keeping it pressed check the manifold pressure with a
manometer; NATURAL gas requires 4.0” W.C.P. and LP/PROPANE requires
11.0” W.C.P.
- Incoming line pressure upstream from the regulator must be 1” W.C.P. higher
than the manifold pressure in order to check the regulator.
- The regulator used on this range can withstand a maximum input pressure of 1/2
PSI (14.0” W.C.P). If the line pressure is in excess of that amount, a step-down
regulator will be required.
f) The appliance, its individual shut-off valve, and pressure regulator must be
disconnected from the gas supply piping system during any pressure testing of
that system at pressures in excess of 1/2 PSI (3.5 kPa).
g) The appliance must be isolated from the gas supply piping system by closing its
individual manual shut-off valve during any pressure testing of the gas supply piping
system at test pressure equal to or less than 1/2 PSI (3.5 kPa).
3. Flexible Connections:
Fig. 2.4
If local codes permit, CSA design-certified, flexible metal appliance connector is
recommended for connecting this range to the gas supply line. Do Not kink or damage
the flexible connector when moving the range. The pressure regulator has 1/2” NPT
female pipe threads.You will need to determine the fittings required, depending on the
size of your gas supply line, flexible metal connector and shutoff valve.
4. Rigid Pipe Connections:
If rigid pipe is used as a gas supply line, a combination of pipe fittings must be used
to obtain an in-line connection to the range. All strains must be removed from the
supply and fuel lines so range will be level and in line.
• Use joint compounds and gaskets that are resistant to action of natural or propane
gas on all male pipe threads.
• Do not over tighten gas fitting when attaching to pressure regulator. Over tightening
may crack regulator.
5. Leak Testing:
IMPORTANT: Leak testing of the appliance shall be conducted as follows:
• After final gas connection is made, turn on manual gas valve and test all
connections in gas supply piping and appliance for gas leaks with a soapy water
solution. During this test all appliance gas valves have to be closed.
• In order to avoid property damage or serious personal injury, never use a Iighted
match. If a leak is present, tighten joint or unscrew, apply more joint compound,
tighten again and retest connection for leak.
18
2
CONVERSION TO LP/PROPANE GAS (OR CONVERSION
BACK TO THE ORIGINAL GAS - NATURAL GAS)
Every range is provided with a set of injectors for the various types of gas.
Select the injectors to be replaced according to the “INJECTORS TABLE”.
The nozzle diameters, expressed in hundredths of a millimetre, are marked on the
body of each injector.
CAUTION: Save the orifices removed from the appliance for future use.
SETTING THE PRESSURE REGULATOR (fig. 2.5)
The pressure regulator is accessible through the storage compartment by opening
the bottom pivoting panel; the pressure regulator is positioned on the rear left side
of the range.
To set the pressure regulator:
1. Unscrew the regulator cover;
2. Unscrew the "A" component, reverse and screw it according to the LP/PROPANE (or
NATURAL GAS) regulation.
Pressure
regulator
1
REGULATOR
COVER
2
A
component
LP/PROPANE
REGULATION
NATURAL GAS
REGULATION
Fig. 2.5
19
2
INJECTORS TABLE
LP/PROPANE
11” W.C.P.
NATURAL GAS
4” W.C.P.
BTU/hr
Ø injector
[1/100 mm]
Ø injector
[1/100 mm]
6000
1500
72
118
12000
5000
102
170
2800 for NATURAL GAS (*)
3500 for LP/PROPANE GAS (*)
1000 (*)
55
(no. 1 central)
80
(no. 1 central)
72
(no. 2 outer)
130
(no. 2 outer)
NOMINAL POWER
REDUCED POWER
BTU/hr
Semi-rapid (R)
Triple ring (TC)
BURNERS
Inner crown
Dual (D)
16000 for NATURAL GAS (#)
6500
for NATURAL GAS (#)
for LP/PROPANE GAS (#)
Outer crowns 15000 for LP/PROPANE GAS (#) 4500
(*) Power calculated only with inner crown operating
(#) Power calculated with inner and outer crowns operating
Triple ring
burner
Semi-rapid
burner
J
Fig. 2.6a
DUAL
burner
J
Injectors for
outer crowns
Fig. 2.6c
20
J
OPERATIONS TO BE
PERFORMED WHEN
SUBSTITUTING THE
INJECTORS
•
Remove the gratings and the burner
covers;
•
Using a wrench substitute the nozzle
injectors “J” (figs. 2.6a - 2.6b - 2.6c)
with those most suitable for the kind
of gas for which it is to be used.
The burner are conceived in such a
way so as not to require the regulation
of the primary air.
Fig. 2.6b
J
Injector for inner crown
2
SETTING THE BURNER MINIMUM
When switching from one type of gas to another, the minimum flow rate must also be
correct: the flame should not go out even when passing suddenly from maximum to
minimum flame.
To regulate the flame follow the instructions below:
Semirapid and triple ring burners
– Light the burner
– Set the gas valve to
position
– Remove the knob
– With a thin screwdriver turn the screw "F" until adjustment is correct (fig. 2.7).
Inside crown of DUAL burner
F
regulation
screw
Fig. 2.7
– Light the DUAL burner
– Set the gas valve to
position
– Remove the knob
– Using a screwdriver turn the screw "H" until the correct setting is obtained (fig. 2.8).
H
G
Outside crowns of DUAL burner
– Light the DUAL burner
– Set the gas valve to
position
– Remove the knob
– Using a screwdriver turn the screw "G" until the correct setting is obtained (fig. 2.8).
For LP/PROPANE gas, tighten the adjustment screws completely.
Fig. 2.8
After regulation repeat the operations indicated in paragraph “2. PRESSURE
REGULATOR” at page 13 and 18.
If the range has been disconnected and then connected again to the gas supply line
repeat the operations indicated in paragraph “5. LEAK TESTING” at page 18.
IMPORTANT:
•
After conversion to LP/PROPANE gas has been carried out affix near the data plate
the conversion label supplied and also affix a conversion label at page 3 of this
instruction manual.
•
After conversion back to the original gas (NATURAL GAS) has been carried
out remove, near the data plate and at page 3 of this instruction manual, the
LP/PROPANE conversion labels. Save the labels removed for future use.
21
electrical connection
3
ELECTRICAL REQUIREMENTS
WARNING
TO AVOID ELECTRICAL SHOCK
HAZARD, BEFORE INSTALLING
THE APPLIANCE, SWITCH POWER
OFF AT THE SERVICE PANEL AND
LOCK THE PANEL TO PREVENT
THE
POWER
FROM
BEING
SWITCHED ON ACCIDENTALLY.
• This appliance must be properly installed and grounded by a qualified technician in
accordance with the National Electrical Code ANSI/NFPA No.70 (latest edition) and
local electrical code requirements. IN CANADA: Electrical installation must be in
accordance with the current CSA C22.1 Canadian Electrical Codes Part1 and/or local
codes.
• This appliance may be connected by means of permanent “Hard Wiring” or “Power
Supply Cord Kit”. Power supply cord is not supplied, but it is available through your
local electric supply house.
• Use only 3-conductor or 4-conductor CSA/UL listed range cord rated at 30 amps with
250 V minimum and provided with ring terminals. These cords should be provided with
strain relief or conduit connector.
Warning: Frame grounded through neutral lead. If used in,
- New branch-circuit installations (1996 NEC),
- Mobile homes,
- Recreational vehicles, or
- In an area where local codes prohibit grounding through neutral, use a 4 conductor
cord or conduit.
• The range must be connected to the proper electrical voltage and frequency as
specified on the rating plate.
• The range can be connected directly to the fused disconnect (or circuit breaker box)
through flexible, armoured or non-metallic sheathed, copper cable (with grounding
wire). Allow two to three feet of slack in the line so that it can be moved if servicing is
ever necessary.
Electrical Shock Hazard
Electrically ground range.Failure to
follow these instruc-tions can result
in death, fire, or electrical shock.
ELECTRICAL CONNECTION WITH POWER CORD
Use a 3-wire power supply cord kit rated for 50 amps - 125/250 volts with closed loop
terminals and marked for use with ranges. Where local codes do not permit grounding
through neutral, use a 4-wire power supply cord kit.
The cord must be secured to the range with a suitable strain relief. The electrical
connection is made at the terminal block, which is located behind the terminal block
access plate on the back of the range.
ELECTRICAL CONNECTION WITH CONDUIT
Use 1/2” (1.3 cm) trade size CSA/UL-listed conduit with a conduit clamp, 16 AWG/600
volt copper conductor colored red for line 1 and black for line 2 and 16 AWG/600 volt
copper conductor (or 12 AWG/600 Volt copper conductor if grounding through neutral)
colored white for neutral with closed loop terminals marked for use with ranges.
Location of
Nameplate
22
Where local codes do not permit grounding through neutral, use a green 12 AWG
copper conductor as directed in the 4-wire connector directions. The conduit must be
secured to the range with the strain relief bracket. The electrical connection is made at
the terminal block which is located behind the terminal block access plate on the back
of the range.
3
3-Wire Power Cord Installation
(See figures 3.1, 3.2 and 3.3)
Fig. 3.1
1. Remove the Terminal Block Access Plate on the back of the
range by unscrewing the 6 fixing Screws (fig. 3.1).
2. Insert the Power Cord through the hole in the Power Cord
Bracket; then tighten the Power Cord by using a suitable
Strain Relief. Allow enough slack to easily attach the cord
terminals to the Terminal Block.
3. Remove the 3 wire terminal nuts and washers from the
Terminal Block.
4. Plug the terminal holes of Power Cord. The Neutral or
Ground Wire of the Power Cord must be connected to the
neutral terminal located in the center of Terminal Block. The
Power Wires must be connected to the outside terminals.
Screws
Terminal Block
Access Plate
5. Plug washers and tighten nuts securely.
Do not remove Ground strap.
Fig. 3.2
6. Assemble the Terminal Block Access Plate.
4-Wire Power Cord Installation
(See figures 3.1, 3.2 and 3.4)
Power Cord
Bracket
1. Remove the Terminal Block Access Plate on the back of the
range by unscrewing the 6 fixing Screws (fig. 3.1).
2. Insert the Power Cord through the hole in the Power Cord
Bracket; then tighten the Power Cord by using a suitable
Strain Relief. Allow enough slack to easily attach the cord
terminals to the Terminal Block.
3. Remove the 3 wire terminal nuts and washers from the
Terminal Block.
Fig. 3.3
Ground strap
Terminal Block
4. Remove the Ground Strap from the frame of range and
terminal by removing its screw and cutting it as shown in
Figure 3.4.
5. Plug the terminal holes of Power Cord. The Neutral Wire of
the Power Cord must be connected to the neutral terminal
located in the center of Terminal Block; the Power Wires
must be connected to the outside terminals; the Ground Wire
must be attached to the frame of range by using the
(Ground) identified Grounding Screw.
Hole D 1" 9/64
(29 mm)
Neutral Wire
Power Wires
Tighten the Power Cord
by using a suitable Strain Relief
Power Cord
6. Plug washers and tighten nuts securely.
7. Assemble the Terminal Block Access Plate.
Fig. 3.4
Cut Ground Strap
Terminal Block
Grounding
Screw
Grounding Wire
Neutral Wire
Power Wires
Tighten the Power Cord
by using a suitable Strain Relief
Power Cord
23
3
Fig. 3.5
3-Wire Conduit Installation
(See figures 3.1, 3.5 and 3.6)
1. Remove the Terminal Block Access Plate on the back of the
range by unscrewing the 6 fixing Screws (fig. 3.1).
2. Feed 1/2” (1.3 cm) trade size Conduit through the hole in the
Conduit Bracket and secure to the Conduit Bracket with a
Conduit Clamp.
3. Remove the 3 wire terminal nuts and washers from the
Terminal Block.
Counduit
Bracket
4. Plug the terminal holes of conductors. The Neutral or Ground
Wire of the Power Cord must be connected to the neutral
terminal located in the center of Terminal Block. The Power
Wires must be connected to the outside terminals.
Hole D 7/8"
(22.5 mm)
5. Plug washers and tighten nuts securely.
Fig. 3.6
Do not remove Ground strap.
6. Assemble the Terminal Block Access Plate.
Ground strap
Terminal Block
Neutral Wire
Power Wires
Conduit Clamp
Conduit
4-Wire Conduit Installation
(See figures 3.1, 3.5 and 3.7)
1. Remove the Terminal Block Access Plate on the back of the
range by unscrewing the 6 fixing Screws (fig. 3.1).
Fig. 3.7
Cut Ground Strap
2. Feed 1/2” (1.3 cm) trade size Conduit through the hole in the
Conduit Bracket and secure to the Conduit Bracket with a
Conduit Clamp.
3. Remove the 3 wire terminal nuts and washers from the
Terminal Block.
Terminal Block
Grounding
Screw
Grounding Wire
Neutral Wire
Power Wires
Conduit Clamp
Conduit
4. Remove the Ground Strap from the frame of range and
terminal by removing its screw and cutting it as shown in
Figure 3.7.
5. Plug the terminal holes of conductors. The Neutral Wire of the
Power Cord must be connected to the neutral terminal
located in the center of Terminal Block; the Power Wires
must be connected to the outside terminals; the Ground Wire
must be attached to the frame of range by using the
(Ground) identified Grounding Screw.
6. Plug washers and tighten nuts securely.
7. Assemble the Terminal Block Access Plate.
24
3
WIRING DIAGRAM
L1
P-E61
P-PR
P-PR
ST
ST-CF
P8
P7
2
AS
TPL
CE
GE
BE
TE
1
A
ISG
E61
CF
B
EARTH
P3 P4 P5 P6
PR
OT
L1 - L2 = 240V
L1 - N = 120V
L2 - N = 120V
OF
LF
P1
IC
P2
P-E61
L2
N
Cod.0422409
ELECTRIC DIAGRAM KEY
PR
E61
P-E61
P-PR
CF
P1...8
AS
OF
TPL
CE
GE
BE
TE
OT
ST
ST-CF
LF
ISG
IC
Electronic programmer
Relay
Relay contact
Programmer contact
Cooling fan
Oven switch contact
Air flow switch
Oven fan
Thermostat pilot lamp
Circular element
Broil element
Bottom element
Top element
Oven thermostat
Safety thermal overload
Cooling fan thermal overload
Oven lamp
Ignition switches group
Ignition coil
25
26
27
The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors
in the present booklet.
The manufacturer reserves the right to make all modifications to its products deemed necessary for
manufacture or commercial reasons at any moment and without prior notice, without jeopardising the
essential functional and safety characteristics of the appliances.
Cod. 1104900 - ß1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement