Avital | 4003 | Quick Reference Install Guide

Quick Reference Install Guide
4003 Remote Start
Remote start (H2) 6-pin connector
H2/1
PINK
OUTPUT TO PRIMARY IGNITION CIRCUIT
H2/2
PURPLE
OUTPUT TO STARTER CIRCUIT
H2/3
ORANGE
OUTPUT TO ACCESSORY CIRCUIT
Wiring Connections
H2/4
RED
(+) (30A) HIGH CURRENT 12V INPUT
H2/5
PINK/WHITE
OUTPUT TO SECOND IGNITION/ACCESSORY CIRCUIT
Main Harness (H1), 9-pin connector
H2/6
RED
(+) (30A) HIGH CURRENT 12V INPUT
H1/1
LIGHT GREEN BLACK
(-) 200mA FACTORY ALARM DISARM
H1/2
GREEN/WHITE
(-) 200mA FACTORY ALARM REARM
H1/3
YELLOW
(+) IGNITION OUT (TO ALARM)
H1/4
WHITE/BLUE
(-) ACTIVATION INPUT
H1/5
ORANGE
(-) 500mA GROUND WHEN LOCKED/ANTI-GRIND OUTPUT
H1/6
BROWN
(-) 200mA HORN OUTPUT
H1/7
RED/WHITE
(-) 200mA TRUNK RELEASE OUTPUT
H1/8
BLACK
GROUND
H1/9
WHITE
(+/-) LIGHT FLASH OUTPUT
BLUE
(-) 200mA STATUS OUTPUT
2
ORANGE
(-) 200mA ACCESSORY OUTPUT
3
PURPLE
(-) 200mA STARTER OUTPUT
4
PINK
(-) 200mA IGNITION OUTPUT
If a feature/virtual tach needs to be reset or the remote controls need to be deleted,
use the following procedure.
To learn the tach signal:
1. Start the vehicle with the key.
2. Within 5 seconds, press and hold the Valet button.
3. After 3 seconds the LED will light constant when the tach signal is learned.
4. Release the Valet button.
1.
2.
Virtual Tach Reset: Deletes all previously learned values for Virtual Tach,
and on the next remote start sequence the unit begins virtual tach initialization.
Note: The “Zap” feature on the Bitwriter does not reset the Virtual tach
setting.
Virtual Tach
Note: Virtual tach is not recommended for diesel trucks
H3/1
BLACK/WHITE
(-) NEUTRAL SAFETY SWITCH INPUT
H3/2
VIOLET/WHITE
TACHOMETER INPUT WIRE
1
BLUE
(-) UNLOCK
H3/3
BROWN
(+) BRAKE SHUTDOWN INPUT WIRE
2
EMPTY
NOT USED
H3/4
GRAY
(-) HOOD PIN SWITCH SHUTDOWN WIRE
(-) LOCK
H3/5
BLUE/WHITE
(-) 200 mA 2ND STATUS/REAR DEFOGGER
To program Virtual Tach:
1. After the install is complete, remote start the car.
2. If the car does not start on the first attempt, let the remote start attempt again.
3. Once the car starts, let it run until the parking lights come on.
4. When the parking lights come on, shut off the remote start with the remote that’s it! Virtual Tach is programmed.
Turn the ignition to the ON position (The heavy gauge pink wire must be connected).
Within 10 seconds, press and release the Valet button: 2 times if you want to
delete remotes, 3 times to reset features or 4 times to reset virtual tach. These
features are described next.
Reset Features: This resets all features of the system to the factory default
settings.
Note: This feature does not delete the remotes from the system or reset
the Virtual Tach setting
If the tachometer input on the system is connected to the vehicle, the D2D tachometer
input will be ignored.
Door Lock, 3-pin connector
GREEN
Tach Learning
When programming tach learning with:
• Analog, the parking lights flash one time
• D2D inerface module, the parking lights flash twice
Remote Start harness (H3), 5-pin connector
3
How to Reset Features and Virtual Tach
Important: This unit can learn the tachometer with the analog input or
through D2D using an interface module. The unit confirms which source
is used.
Satellite harness - 4-pin connector
1
Installation Points
Note: Channel 1 and 2 are unavailable.
3.
4.
Once you have selected the function step, press the Valet button once more
and hold it. The LED flashes to confirm the selected channel. Do not release
the Valet button.
Activate input. When the white/blue is pulsed the LED comes on solid to
confrim the reset.
Once the feature is reset, the Valet button can be released.
Virtual Tach handles disengaging the starter motor during remote starting – it does
not address over-rev. If the customer wants to have the over-rev protection capability, the tach wire must be connected. This may involve more installation shop
charges than initially quoted.
Important: If the Virtual Tach mode over cranks or doesn't crank the
vehicle long enough to start and run the car, use the Bitwriter to add or
subtract the starter output time. You can adjust the output time in increments of 50msec of the learned time using the Bitwriter.
Red 4-pin port, Bitwriter/ESP2 or D2D programming
Activation input (+/-)
Parking light Jumpers
Side View
Red 4-pin port, Bitwriter/ESP2 or D2D
Antenna
The Red 4-pin plug may be configured as a Bitwriter/ESP2 or D2D port.
The factory default is Bitwriter/ESP2 mode.
Side View
LED (Programming
indicator)
Control Button
(Valet Switch)
Heavy
Gauge
Relay
Door Lock/unlock
Harness
4003
Satellite Harness
Primary Harness
Remote Start Harness
Antenna
To use as D2D mode follow the below steps:
1. Make sure White/Blue activation wire is grounded.
2. Power the unit up. The system LED flashes for 5 seconds to confirm D2D mode
change.
3. Remove the White/Blue wire from ground.
To change from D2D to Bitwriter/ESP2 mode:
1. Make sure the White/Blue activation wire is grounded.
2. Power the unit up, the system LED turns on solid for 5 seconds to confirm Bitwriter/ESP2 mode change.
3. Remove the White/Blue wire from ground.
The procedure can be repeated to toggle from one mode to the other.
Important: If you power up the system with the White/Blue activation
wire ungrounded, the system LED will come on solid for 5 seconds indicating the system is in Bitwriter/ESP2 mode.
© 2011 Directed Electronics. All rights Reserved.
1
Programming System Features
Remote Start Shutdown Diagnostics
The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the
feature settings using the Valet button.
To perform shutdown diagnostics:
1. With the ignition Off, press and hold the Valet button.
2. Turn the ignition On and then back Off while holding the Valet button.
3. Release the Valet button.
4. Press and release the Valet button. The LED flashes to report the last shutdown for one minute or until the
ignition is turned on, as shown in the following table:
1.
2.
3.
4.
5.
Turn the ignition on, then off.
Select a Menu. Press and hold the Valet button. When the LED flashes once, Menu One has been selected. Continue to hold the switch until the LED flashes twice. Menu Two has now been selected.Release
the Program switch after the desired Menu choice has been selected.
Choose. Within 10 seconds, press and release the Valet button the number of times corresponding to the
feature number you want to program. (See Features Menu section.)
Once the Valet button has been pressed and released the desired number of times, press it once more and
hold it. After a second, the LED will flash to indicate which feature you have accessed. For example, groups
of eight flashes would indicate access to the status output feature (Feature 8 of menu 2).
Activate Input. Each time the white/blue is pulsed, the LED will turn on or off indicating the feature setting.
If the feature has more than two selections, each time this input is pulsed the next available setting will be
picked. For example if 60 minute runtime is chosen, (Feature 2, Menu 2) the LED flashes 3 times.
Release. The Valet button can now be released.
LED Flashes
1 flash
2 flashes
3 flashes
4 flashes
5 flashes
6 flashes
7 flashes
8 flashes
Menu 2
Shutdown Mode
Timed out
Over-rev shutdown
Low or no RPM, low battery (voltage and virtual tach modes)
Transmitter shutdown (or optional push button)
(-) Hood Shutdown (H3/4 GRAY)
(+) Shutdown (H3/3 BROWN)
(-) Neutral safety shutdown (H3/1 BLACK/WHITE)
Wait-to-start timed out
Feature Menus
Default settings are in bold type.
Once a feature is programmed:
• Other features can be programmed within the same menu
• Another menu can be selected
• The learn routine can be exited if programming is complete
Menu 1
To access another feature in the same menu:
1. Press and release the Valet button the number of times necessary to advance from the feature you just programmed to the next one you want to program.
2. Then press the Valet button once more and hold it.
To select another menu:
1. Press and hold the Valet button.
2. After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
The learn routine exits if any of the following occurs:
• The ignition is turned On
• There is no activity for 30 seconds
• The Valet button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine has
previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the Valet
button.
The Bitwriter®
gives you access to a wider range of system options. These features and the adjustments that
may be programmed are described in the table below.
Feature #
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
Opt. 5+
1
Horn function
Off
Siren
20 mS
Siren
30 mS
Siren
40 mS
Siren
50 mS
2
Ignition controlled lock
On
Off
3
Ignition controlled unlock
On
Off
4
Doorlock output duration
0.8 sec.
3.5 sec.
5
Double pulse
unlock
Off
On
6
Double pulse
lock
Off
On
7
Factory Alarm
Disarm function
with unlock
Before unlock
8
Factory Alarm
Disarm Pulses
Single
Double
9
Comfort
Closure
Comfort
Closure 1
Off
Panic
On
Off
10
0.4 sec.
Feature #
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
1
Engine checking
Virtual tach
voltage
Off
tachometer
2
Engine
Runtime
12 min
24 min
60 min
3
Park light
output
Pulsed
Constant
4
Cranking time
0.6 sec.
0.8 sec.
1.0 sec.
5
Activation
pulse count
1 pulse
2 pulses
3 pulses
6
2nd Ignition
behavior
Ignition
Accessory
7
Accessory
output
Off during
wait-to-start
On during
wait-to-start
8
2nd Status
behavior
Normal
Latch rear
defogger
9
Anti-grind
On
Off
10
Diesel start
delay
Off
Timed 15 sec
Timed 30 sec.
Timed 45 sec.
11
Timer mode
run time
12 min
3 min
6 min
9 min
1.4,
1.6,
1.8,
2.0,
4.0 sec
Pulse rear
defogger
Bitwriters with a date code of 6a Directed
or olderLogo
require
Usagean IC
upgrade (p/n 998M). Some bitwriters with a date code
of 6B do not require the IC upgrade, refer to tech tip #
1112 for more information.
The Bitwriter® (p/n 998U)
requires chip version 2.7 or
Logo, Directed with designed
in USA.eps
newer
to program this unit.
Remote start
only
Comfort
Closure 2
1.2 sec.
Opt. 5+
See full Installation Guide for more
detailed information on this system.
Such information and more can be
found online at:
www.directechs.com
Logo, Directed Electronics w-driven.eps
Menu Item
Feature
Default
Options
1
Engine Runtime
12 min.
1-60 min.
2
Diesel start type
Off
Timed
3
Diesel start delay time (seconds)
15 sec
1-90 sec.
4
Virtual Tach Fine Tune
Not initialized
0 to 1 second in 50 millisecond
increments
5
Remote control programming
Unlocked
Locked
6
Feature Programming
Unlocked
Locked
Logo, Directed with Distributed By.eps
QRN4003 2011 -12
© 2010 Directed Electronics. All rights Reserved.
2
Download PDF