PictureMate Pal - Start Here Card

Start Here
PM 200
2
1
Connect the power adapter to the back of
PictureMate Pal.
2
Connect the power
cable to the power
adapter.
3
Set up your PictureMate Pal
and print –no computer
required!
4
Note: To print from your computer, see
Plug In and Turn On
Slide the cartridge lever left
to the Release position.
3
Remove the initial photo cartridge
from its package.
Plug the other end
of the power cable
into a power outlet.
Caution: Do not install a
different PictureMate Pal
cartridge for initial setup.
Install only the initial photo cartridge
that came with PictureMate Pal.
Flip the handle to the back.
the Basics book and your CD after completing these steps.
1
2
4
Slide the cartridge straight into the slot, label side up,
until it clicks into place. It will not go in all the way.
5
Slide the lever all the way right, to the Lock position.
Unpack
PictureMate Pal comes with all these items in the box.
5
PictureMate Pal
PictureMate Pal
photo paper
Power adapter
Open the paper support.
Power cable
Initial PictureMate Pal
photo cartridge
6
Press the
On button to turn on PictureMate Pal.
After a moment, you see
this on the photo
viewer screen:
Basics book
PictureMate Pal
Printer Software CD
1
Remove all the tape and packing material from the
outside of PictureMate Pal.
2
Open the cartridge door
on the back of
PictureMate Pal.
3
Remove the packing
material from inside the
cartridge slot.
4
Close the cartridge door.
Caution: If the cartridge is not inserted correctly,
ink may leak.
6
Close the cartridge door.
Initial Charge
Charging.
Please wait.
Now you can install your initial photo cartridge.
PictureMate Pal charges the print head for
3 to 4 minutes and displays the screen above.
3
1
Install the Initial
Photo Cartridge
7
When you see the
Charging complete
message on the photo
viewer screen, press OK.
Open the cartridge door.
Press OK
*410591100*
*410591100*
Turn over
Start Here
PM 200
2
1
Connect the power adapter to the back of
PictureMate Pal.
2
Connect the power
cable to the power
adapter.
3
Set up your PictureMate Pal
and print –no computer
required!
4
Note: To print from your computer, see
Plug In and Turn On
Slide the cartridge lever left
to the Release position.
3
Remove the initial photo cartridge
from its package.
Plug the other end
of the power cable
into a power outlet.
Caution: Do not install a
different PictureMate Pal
cartridge for initial setup.
Install only the initial photo cartridge
that came with PictureMate Pal.
Flip the handle to the back.
the Basics book and your CD after completing these steps.
1
2
4
Slide the cartridge straight into the slot, label side up,
until it clicks into place. It will not go in all the way.
5
Slide the lever all the way right, to the Lock position.
Unpack
PictureMate Pal comes with all these items in the box.
5
PictureMate Pal
PictureMate Pal
photo paper
Power adapter
Open the paper support.
Power cable
Initial PictureMate Pal
photo cartridge
6
Press the
On button to turn on PictureMate Pal.
After a moment, you see
this on the photo
viewer screen:
Basics book
PictureMate Pal
Printer Software CD
1
Remove all the tape and packing material from the
outside of PictureMate Pal.
2
Open the cartridge door
on the back of
PictureMate Pal.
3
Remove the packing
material from inside the
cartridge slot.
4
Close the cartridge door.
Caution: If the cartridge is not inserted correctly,
ink may leak.
6
Close the cartridge door.
Initial Charge
Charging.
Please wait.
Now you can install your initial photo cartridge.
PictureMate Pal charges the print head for
3 to 4 minutes and displays the screen above.
3
1
Install the Initial
Photo Cartridge
7
When you see the
Charging complete
message on the photo
viewer screen, press OK.
Open the cartridge door.
Press OK
*410591100*
*410591100*
Turn over
Start Here
PM 200
2
1
Connect the power adapter to the back of
PictureMate Pal.
2
Connect the power
cable to the power
adapter.
3
Set up your PictureMate Pal
and print –no computer
required!
4
Note: To print from your computer, see
Plug In and Turn On
Slide the cartridge lever left
to the Release position.
3
Remove the initial photo cartridge
from its package.
Plug the other end
of the power cable
into a power outlet.
Caution: Do not install a
different PictureMate Pal
cartridge for initial setup.
Install only the initial photo cartridge
that came with PictureMate Pal.
Flip the handle to the back.
the Basics book and your CD after completing these steps.
1
2
4
Slide the cartridge straight into the slot, label side up,
until it clicks into place. It will not go in all the way.
5
Slide the lever all the way right, to the Lock position.
Unpack
PictureMate Pal comes with all these items in the box.
5
PictureMate Pal
PictureMate Pal
photo paper
Power adapter
Open the paper support.
Power cable
Initial PictureMate Pal
photo cartridge
6
Press the
On button to turn on PictureMate Pal.
After a moment, you see
this on the photo
viewer screen:
Basics book
PictureMate Pal
Printer Software CD
1
Remove all the tape and packing material from the
outside of PictureMate Pal.
2
Open the cartridge door
on the back of
PictureMate Pal.
3
Remove the packing
material from inside the
cartridge slot.
4
Close the cartridge door.
Caution: If the cartridge is not inserted correctly,
ink may leak.
6
Close the cartridge door.
Initial Charge
Charging.
Please wait.
Now you can install your initial photo cartridge.
PictureMate Pal charges the print head for
3 to 4 minutes and displays the screen above.
3
1
Install the Initial
Photo Cartridge
7
When you see the
Charging complete
message on the photo
viewer screen, press OK.
Open the cartridge door.
Press OK
*410591100*
*410591100*
5
4 Load Paper
PictureMate Pal comes with geniune Epson glossy photo paper
made especially for printing lab quality photos.
Caution: Don’t load or print on plain paper; this may damage
PictureMate Pal.
1
1
Move the handle to the back.
2
Insert your memory card into the correct slot on
PictureMate Pal.
Memory card light
SD™ (Secure Digital)
SDHC™ (High Capacity)
mini SD™ *
mini SDHC *
micro SD *
micro SDHC
MMC™ (MultiMediaCard™)
xD Picture Card™
xD Picture Card (Type M and Type H)
Sony Memory Stick® **
Memory Stick Duo™ *
Memory Stick PRO™
Memory Stick PRO Duo™ *
MagicGate™ Memory Stick **
MagicGate Memory Stick Duo™ *
Top
2
Open the paper support.
Microdrive™
CompactFlash™ (Type I and II)
3
Press the Open button to
open the output tray.
1
Press Select All.
2
To print more than one copy of all the photos, press to increase the number of copies. (Press to decrease
the number.)
3
Continue with “Print Selected Photos” below.
Remove the memory card containing photos from
your digital camera.
Insert a Memory
Card
Select All Photos
Bottom
Print Selected Photos
1
Press Layout to select the layout
of your photos on the paper.
Note: You can access other print
options by pressing the Menu button,
including selecting a Proof Sheet
layout containing small images
(thumbnails) of all your photos.
2
Press Print.
3
Press or to review your selected photos and copies
on the preview screen.
4
Press Print to print your photos.
* Adapter required
** Maximum capacity 128MB
4
3
Push the card in until it stops (it won’t go in all the
way). The memory card light comes on and
PictureMate Pal tells you how many photos are
on the card.
Note: Insert just one card at a time. PictureMate Pal does
not read multiple cards at once.
Slide the edge guides outward.
6
5
Load up to 20 sheets at a time. Fan the sheets to
slightly separate them.
6
Place your paper into the slot between the edge
guides with the glossy side up. Slide the edge guides
inward slightly.
Print Your Photos
PictureMate Pal’s photo viewer screen
makes it easy to select the photos
you want to print.
More on PictureMate Pal
Check your printed manual
See the Basics book for instructions on
printing from PictureMate Pal, your computer,
and other devices. Also learn how to save
photos on your computer, replace your Print
Pack (photo paper and photo cartridge), take
care of PictureMate Pal, and solve problems.
Check your on-screen manual
When you install your PictureMate Pal software
from the CD, you’ll see an icon for your on-screen
PictureMate Pal User’s Guide on your computer
screen. Double-click that icon for comprehensive
instructions on using PictureMate Pal and its software.
Note: For information on possible software updates for PictureMate
Load glossy side up
Make sure paper
is beneath arrow
on edge guide
Note: Keep unused paper in the original package and store it flat to
prevent curling.
Select Some Photos
1
Press or to view the photo you want to print.
2
Press OK to select it.
3
To print more than one copy, press OK to increase
the number of copies. (Press Cancel to decrease the
number.)
4
To select more photos, press or to view the photo
and press OK to select it. Repeat step 3 to select more
copies, if necessary.
5
Continue with “Print Selected Photos” to the right.
Pal, go to http://support.epson.com, select Printers, and select your
product under Personal Photo Lab. Then check for updated software
in the Drivers & Downloads section.
Caution: To avoid damaging your PictureMate Pal,
keep it out of the sun and don’t leave it in your car
or other location where it can get too hot or too cold.
Epson and PictureMate are registered trademarks and Exceed Your Vision is a
trademark of Seiko Epson Corporation.
General Notice: Other product names used herein are for identification purposes
only and may be trademarks of their respective owners. Epson disclaims any and
all rights in those marks.
© 2006 Epson America, Inc. 5/06
CPD-21347
Printed in XXXXXX XX.XX-XX XXX
5
4 Load Paper
PictureMate Pal comes with geniune Epson glossy photo paper
made especially for printing lab quality photos.
Caution: Don’t load or print on plain paper; this may damage
PictureMate Pal.
1
1
Move the handle to the back.
2
Insert your memory card into the correct slot on
PictureMate Pal.
Memory card light
SD™ (Secure Digital)
SDHC™ (High Capacity)
mini SD™ *
mini SDHC *
micro SD *
micro SDHC
MMC™ (MultiMediaCard™)
xD Picture Card™
xD Picture Card (Type M and Type H)
Sony Memory Stick® **
Memory Stick Duo™ *
Memory Stick PRO™
Memory Stick PRO Duo™ *
MagicGate™ Memory Stick **
MagicGate Memory Stick Duo™ *
Top
2
Open the paper support.
Microdrive™
CompactFlash™ (Type I and II)
3
Press the Open button to
open the output tray.
1
Press Select All.
2
To print more than one copy of all the photos, press to increase the number of copies. (Press to decrease
the number.)
3
Continue with “Print Selected Photos” below.
Remove the memory card containing photos from
your digital camera.
Insert a Memory
Card
Select All Photos
Bottom
Print Selected Photos
1
Press Layout to select the layout
of your photos on the paper.
Note: You can access other print
options by pressing the Menu button,
including selecting a Proof Sheet
layout containing small images
(thumbnails) of all your photos.
2
Press Print.
3
Press or to review your selected photos and copies
on the preview screen.
4
Press Print to print your photos.
* Adapter required
** Maximum capacity 128MB
4
3
Push the card in until it stops (it won’t go in all the
way). The memory card light comes on and
PictureMate Pal tells you how many photos are
on the card.
Note: Insert just one card at a time. PictureMate Pal does
not read multiple cards at once.
Slide the edge guides outward.
6
5
Load up to 20 sheets at a time. Fan the sheets to
slightly separate them.
6
Place your paper into the slot between the edge
guides with the glossy side up. Slide the edge guides
inward slightly.
Print Your Photos
PictureMate Pal’s photo viewer screen
makes it easy to select the photos
you want to print.
More on PictureMate Pal
Check your printed manual
See the Basics book for instructions on
printing from PictureMate Pal, your computer,
and other devices. Also learn how to save
photos on your computer, replace your Print
Pack (photo paper and photo cartridge), take
care of PictureMate Pal, and solve problems.
Check your on-screen manual
When you install your PictureMate Pal software
from the CD, you’ll see an icon for your on-screen
PictureMate Pal User’s Guide on your computer
screen. Double-click that icon for comprehensive
instructions on using PictureMate Pal and its software.
Note: For information on possible software updates for PictureMate
Load glossy side up
Make sure paper
is beneath arrow
on edge guide
Note: Keep unused paper in the original package and store it flat to
prevent curling.
Select Some Photos
1
Press or to view the photo you want to print.
2
Press OK to select it.
3
To print more than one copy, press OK to increase
the number of copies. (Press Cancel to decrease the
number.)
4
To select more photos, press or to view the photo
and press OK to select it. Repeat step 3 to select more
copies, if necessary.
5
Continue with “Print Selected Photos” to the right.
Pal, go to http://support.epson.com, select Printers, and select your
product under Personal Photo Lab. Then check for updated software
in the Drivers & Downloads section.
Caution: To avoid damaging your PictureMate Pal,
keep it out of the sun and don’t leave it in your car
or other location where it can get too hot or too cold.
Epson and PictureMate are registered trademarks and Exceed Your Vision is a
trademark of Seiko Epson Corporation.
General Notice: Other product names used herein are for identification purposes
only and may be trademarks of their respective owners. Epson disclaims any and
all rights in those marks.
© 2006 Epson America, Inc. 5/06
CPD-21347
Printed in XXXXXX XX.XX-XX XXX
5
4 Load Paper
PictureMate Pal comes with geniune Epson glossy photo paper
made especially for printing lab quality photos.
Caution: Don’t load or print on plain paper; this may damage
PictureMate Pal.
1
1
Move the handle to the back.
2
Insert your memory card into the correct slot on
PictureMate Pal.
Memory card light
SD™ (Secure Digital)
SDHC™ (High Capacity)
mini SD™ *
mini SDHC *
micro SD *
micro SDHC
MMC™ (MultiMediaCard™)
xD Picture Card™
xD Picture Card (Type M and Type H)
Sony Memory Stick® **
Memory Stick Duo™ *
Memory Stick PRO™
Memory Stick PRO Duo™ *
MagicGate™ Memory Stick **
MagicGate Memory Stick Duo™ *
Top
2
Open the paper support.
Microdrive™
CompactFlash™ (Type I and II)
3
Press the Open button to
open the output tray.
1
Press Select All.
2
To print more than one copy of all the photos, press to increase the number of copies. (Press to decrease
the number.)
3
Continue with “Print Selected Photos” below.
Remove the memory card containing photos from
your digital camera.
Insert a Memory
Card
Select All Photos
Bottom
Print Selected Photos
1
Press Layout to select the layout
of your photos on the paper.
Note: You can access other print
options by pressing the Menu button,
including selecting a Proof Sheet
layout containing small images
(thumbnails) of all your photos.
2
Press Print.
3
Press or to review your selected photos and copies
on the preview screen.
4
Press Print to print your photos.
* Adapter required
** Maximum capacity 128MB
4
3
Push the card in until it stops (it won’t go in all the
way). The memory card light comes on and
PictureMate Pal tells you how many photos are
on the card.
Note: Insert just one card at a time. PictureMate Pal does
not read multiple cards at once.
Slide the edge guides outward.
6
5
Load up to 20 sheets at a time. Fan the sheets to
slightly separate them.
6
Place your paper into the slot between the edge
guides with the glossy side up. Slide the edge guides
inward slightly.
Print Your Photos
PictureMate Pal’s photo viewer screen
makes it easy to select the photos
you want to print.
More on PictureMate Pal
Check your printed manual
See the Basics book for instructions on
printing from PictureMate Pal, your computer,
and other devices. Also learn how to save
photos on your computer, replace your Print
Pack (photo paper and photo cartridge), take
care of PictureMate Pal, and solve problems.
Check your on-screen manual
When you install your PictureMate Pal software
from the CD, you’ll see an icon for your on-screen
PictureMate Pal User’s Guide on your computer
screen. Double-click that icon for comprehensive
instructions on using PictureMate Pal and its software.
Note: For information on possible software updates for PictureMate
Load glossy side up
Make sure paper
is beneath arrow
on edge guide
Note: Keep unused paper in the original package and store it flat to
prevent curling.
Select Some Photos
1
Press or to view the photo you want to print.
2
Press OK to select it.
3
To print more than one copy, press OK to increase
the number of copies. (Press Cancel to decrease the
number.)
4
To select more photos, press or to view the photo
and press OK to select it. Repeat step 3 to select more
copies, if necessary.
5
Continue with “Print Selected Photos” to the right.
Pal, go to http://support.epson.com, select Printers, and select your
product under Personal Photo Lab. Then check for updated software
in the Drivers & Downloads section.
Caution: To avoid damaging your PictureMate Pal,
keep it out of the sun and don’t leave it in your car
or other location where it can get too hot or too cold.
Epson and PictureMate are registered trademarks and Exceed Your Vision is a
trademark of Seiko Epson Corporation.
General Notice: Other product names used herein are for identification purposes
only and may be trademarks of their respective owners. Epson disclaims any and
all rights in those marks.
© 2006 Epson America, Inc. 5/06
CPD-21347
Printed in XXXXXX XX.XX-XX XXX