Dynamix DW 1 - FXS
Dynamix DW FXS – 02
Dynamix DW FXS - 04
FXS Gateway (H.323)
User Manual
FXS H.323 VoIP Gateway User Manual
Table of Contents
TABLE OF CONTENTS ................................................................................................................... II
LIST OF FIGURES ..........................................................................................................................V
LIST OF TABLE .........................................................................................................................VIII
PREFACE .................................................................................................................................... IX
VOIP GATEWAY OVERVIEW ...................................................................................................1
CHAPTER 1 VOIP GATEWAY OVERVIEW .......................................................................................2
1.1 VoIP Gateway Overview ....................................................................................................2
1.2 Features of The VoIP Gateway ..........................................................................................2
1.3 Default Settings..................................................................................................................3
1.4 Front Panels ......................................................................................................................3
1.5 Back Panel Ports ...............................................................................................................4
1.6 Hardware Specifications....................................................................................................4
1.7 Additional Installation Requirements ................................................................................9
1.8 Setting Up the TCP/IP Protocol ........................................................................................9
1.9 Power Up Your VoIP Gateway .........................................................................................10
WEB CONFIGURATION WITH VOIP GATEWAY ..............................................................12
CHAPTER 2 WEB CONFIGURATION WITH FXS INTRODUCTION ...................................................13
2.1 Web Configuration with FXS Overview ...........................................................................13
2.2 Accessing the Web Configuration ....................................................................................13
2.3 Login and welcome screen...............................................................................................13
2.4 Welcome Screen ...............................................................................................................13
2.5 Saving Your Configuration ..............................................................................................15
2.6 Navigating the Web Configuration ..................................................................................16
CHAPTER 3 INITIAL CONFIGURATION ..........................................................................................17
3.1 Initial Configuration Overview .......................................................................................17
3.2 General Configuration ....................................................................................................17
3.3 Static IP address ..............................................................................................................17
3.4 DHCP mode .....................................................................................................................19
3.5 PPPoE mode ....................................................................................................................20
3.6 IP Sharing Configuration ................................................................................................22
3.7 PPPoE (NAT) mode (1A-FXS).........................................................................................24
CHAPTER 4 MAKING A VOIP CALL .............................................................................................27
4.1 Configure the gateway into the Peer-to-Peer mode ........................................................27
4.2 Configure the gateway into the GK routed mode ............................................................30
CHAPTER 5 UPGRADE ROM VERSION ........................................................................................33
5.1 Before you start downloading..........................................................................................33
Table of Connect
II
FXS H.323 VoIP Gateway User Manual
5.2 Update Application Version .............................................................................................33
5.3 Update Boot2m Version ...................................................................................................35
CHAPTER 6 NETWORK INTERFACE SCREEN ................................................................................39
6.1 Network Interface Overview ............................................................................................39
6.2 Network Interface Screen.................................................................................................39
CHAPTER 7 H323 CONFIGURATION SCREEN ...............................................................................42
7.1 H323 Configuration Overview ........................................................................................42
7.2 H323 Configuration Screen .............................................................................................42
CHAPTER 8 LINE CONFIGURATION SCREEN ................................................................................45
8.1 Line Configuration Overview ..........................................................................................45
8.2 Line Configuration Screen...............................................................................................45
CHAPTER 9 PHONE BOOK CONFIGURATION SCREEN ...................................................................47
9.1 Phone Book Configuration Overview ..............................................................................47
9.2 Phone Book Configuration Screen ..................................................................................47
CHAPTER 10 SUPPORT CONFIGURATION SCREEN ........................................................................49
10.1 Support Configuration Overview...................................................................................49
10.2 Support Configuration Screen .......................................................................................49
CHAPTER 11 SYSTEM CONFIGURATION SCREEN .........................................................................51
11.1 System Configuration Overview ....................................................................................51
11.2 System Configuration Screen .........................................................................................51
CHAPTER 12 VOICE CONFIGURATION SCREEN ............................................................................53
12.1 Voice Configuration Overview.......................................................................................53
12.2 Voice Configuration Screen ...........................................................................................53
CHAPTER 13 PHONE CONFIGURATION SCREEN ...........................................................................55
13.1 Phone Configuration Overview .....................................................................................55
13.2 Phone Configuration Screen..........................................................................................55
CHAPTER 14 RTP PAYLOAD TYPE CONFIGURATION SCREEN ......................................................57
14.1 RTP Payload Type Configuration Overview .................................................................57
14.2 RTP Payload Type Configuration Screen ......................................................................57
CHAPTER 15 IP PACKET TOS CONFIGURATION SCREEN .............................................................59
15.1 IP Packet ToS Overview.................................................................................................59
15.2 IP Packet ToS Configuration Screen .............................................................................59
CHAPTER 16 DDNS DEVICE CONFIGURATION SCREEN ..............................................................61
16.1 DDNS Device Configuration Overview.........................................................................61
16.2 DDNS Device Configuration Screen .............................................................................61
CHAPTER 17 PREFIX DROP/INSERT CONFIGURATION SCREEN .....................................................63
17.1 Prefix Drop/Insert Configuration Overview ..................................................................63
17.2 Prefix Drop/Insert Configuration Screen ......................................................................63
Table of Connect
III
FXS H.323 VoIP Gateway User Manual
CHAPTER 18 PASSWORD CONFIGURATION SCREEN .....................................................................65
18.1 Password Configuration Overview................................................................................65
18.2 Password Configuration Screen ....................................................................................65
CHAPTER 19 VERSION AND INFORMATION SCREEN ....................................................................67
19.1 Version and Information Overview ................................................................................67
19.2 Version and Information Screen ....................................................................................67
CHAPTER 20 ROM UPGRADE SCREEN .......................................................................................68
20.1 ROM Configuration Overview.......................................................................................68
20.2 ROM Configuration Screen ...........................................................................................68
CHAPTER 21 FLASH CLEAN SCREEN ...........................................................................................70
21.1 Flash Clean Overview ...................................................................................................70
21.2 Flash Clean Screen ........................................................................................................70
CHAPTER 22 COMMIT DATA SCREEN ..........................................................................................71
22.1 Commit Configuration Data Overview..........................................................................71
22.2 Commit Configuration Data Screen ..............................................................................71
CHAPTER 23 REBOOT SYSTEM SCREEN ......................................................................................72
23.1 Reboot VoIP Gateway Overview....................................................................................72
23.2 Reboot VoIP Gateway Screen ........................................................................................72
COMMAND WITH VOIP GATEWAY .....................................................................................73
CHAPTER 24 COMMAND LIST .....................................................................................................74
24.1 Hyper Terminal Setting ..................................................................................................74
24.2 Power Up Your Gateway ...............................................................................................75
24.3 Command Structure with Gateway ................................................................................77
24.4 Application modes .........................................................................................................78
24.5 How to upgrade .............................................................................................................89
24.6 Commands with Gateway ..............................................................................................92
24.7 System Commands Overview .........................................................................................93
Table of Connect
IV
FXS H.323 VoIP Gateway User Manual
List of Figures
Figure 1-1 Dynamix DW-1 FXS Gateway Front Panel .......................................................4
Figure 1-3 Dynamix DW- FXS 02 Gateway Front Panel ....................................................4
Figure 1-4 Dynamix DW- FXS 04 Gateway Front Panel ....................................................4
Figure 1-5 Dynamix DW- FXS 01 Gateway Back Panel Ports ...........................................4
Figure 1-7 Dynamix DW- FXS 02 Gateway Back Panel Ports ...........................................4
Figure 1-8 Dynamix DW- FXS 04 Gateway Back Panel Ports ...........................................4
Figure 2-2 VoIP Gateway web configuration welcome screen..........................................14
Figure 2-3 Network Interface Screen ................................................................................16
Figure 3-1 Network Interface ............................................................................................18
Figure 3-2 Commit Configuration Data ............................................................................18
Figure 3-3 Reboot VoIP Gateway ......................................................................................19
Figure 3-4 Network Interface ............................................................................................20
Figure 3-5 PPPoE Device Configuration...........................................................................21
Figure 3-6 Enable the IP sharing function .........................................................................24
Figure 3-7 PPPoE Device Configuration...........................................................................25
Figure 4-1 H323 Configuration – Peer to Peer mode Screen ............................................28
Figure 4-2 Phone Book ......................................................................................................28
Figure 4-3 Phone Book – New Record..............................................................................29
Figure 4-4 Phone Book ......................................................................................................29
Figure 4-5 Configure the GK info .....................................................................................31
Figure 5-1 ROM Configuration .........................................................................................33
Figure 5-2 ROM File Upgrade ok .....................................................................................34
Figure 5-3 Flash Clean ......................................................................................................34
Figure 5-4 Flash Clean OK................................................................................................35
Figure 5-5 ROM File Upgrade ok .....................................................................................36
Figure 5-6 Flash Clean ......................................................................................................37
Figure 5-7 Flash Clean OK................................................................................................37
Figure 6-1 Network Interface ............................................................................................40
Figure 7-1 H323 Configuration .........................................................................................43
Figure 8-1 Line Configuration Information.......................................................................45
Figure 9-1 Phone Book ......................................................................................................47
Figure 10-1 Support Configuration ...................................................................................49
Figure 11-1 System Configuration ....................................................................................51
Figure 12-1 Voice Configuration .......................................................................................53
Figure 13-1 Phone Configuration ......................................................................................55
Figure 14-1 RTP Payload Type Configuration ..................................................................57
Figure 15-1 IP Packet ToS Configuration..........................................................................59
List of Figure
V
FXS H.323 VoIP Gateway User Manual
Figure 16-1 DDNS Device Configuration .........................................................................61
Figure 17-1 Prefix Drop/Insert Configuration ...................................................................63
Figure 18-1 Password Configuration.................................................................................65
Figure 19-1 Version and Information ................................................................................67
Figure 20-1 ROM Configuration .......................................................................................68
Figure 21-1 Flash Clean ....................................................................................................70
Figure 22-1 Commit Configuration Data ..........................................................................71
Figure 23-1 Reboot VoIP Gateway ....................................................................................72
Figure 24-1 Connection Description .................................................................................74
Figure 24-2 Connection Description .................................................................................74
Figure 24-3 Connect To .....................................................................................................75
Figure 24-4 Com Properties ..............................................................................................75
Figure 24-5 Initial Screen ..................................................................................................76
Figure 24-6 Login Screen ..................................................................................................77
Figure 24-7 password –set command ................................................................................77
Figure 24-8 quit commend ................................................................................................94
Figure 24-9 debug commend list .......................................................................................94
Figure 24-10 debug –status commend ...............................................................................95
Figure 24-11 reboot commend...........................................................................................95
Figure 24-12 flash commend list .......................................................................................96
Figure 24-13 flash –clean commend .................................................................................97
Figure 24-14 commit commend ........................................................................................97
Figure 24-15 ifaddr commend list .....................................................................................98
Figure 24-16 ifaddr –print command...............................................................................100
Figure 24-17 time commend list......................................................................................100
Figure 24-18 ping commend list......................................................................................101
Figure 24-19 sysconf commend list.................................................................................102
Figure 24-20 sysconf -print commend.............................................................................103
Figure 24-21 h323 commend list .....................................................................................105
Figure 24-22 h323 -print commend (Gatekeeper mode) .................................................107
Figure 24-23 h323 -print commend (Peer to Peer mode) ................................................107
Figure 24-24 line commend list .......................................................................................108
Figure 24-25 line -print commend ...................................................................................109
Figure 24-26 prefix commend list ...................................................................................109
Figure 24-27 prefix –print commend...............................................................................110
Figure 24-28 pbook commend list ................................................................................... 111
Figure 24-29 pbook -print commend ...............................................................................112
Figure 24-30 voice commend list ....................................................................................114
List of Figure
VI
FXS H.323 VoIP Gateway User Manual
Figure 24-31 voice –print commend ...............................................................................115
Figure 24-32 support commend list .................................................................................116
Figure 24-33 support –print commend ............................................................................117
Figure 24-34 sysinfo commend list .................................................................................118
Figure 24-35 phone commend list ...................................................................................119
Figure 24-36 phone –print rbt commend .........................................................................120
Figure 24-37 phone –print rbt commend .........................................................................120
Figure 24-38 phone –print bt commend ..........................................................................121
Figure 24-39 phone –print dt commend ..........................................................................121
Figure 24-40 phone –print flash commend......................................................................121
Figure 24-41 tos commend list ........................................................................................122
Figure 24-42 tos -print commend ....................................................................................122
Figure 24-43 ddns commend list .....................................................................................123
Figure 24-44 ddns -print commend .................................................................................124
Figure 24-45 pt commend List ........................................................................................125
Figure 24-46 pt -print commend......................................................................................125
Figure 24-47 rom commend List .....................................................................................126
Figure 24-48 rom –print commend..................................................................................126
Figure 24-49 passwd commend List................................................................................127
Figure 24-50 passwd –set commend ...............................................................................127
Figure 24-51 passwd –clean commend ...........................................................................127
List of Figure
VII
FXS H.323 VoIP Gateway User Manual
List of Table
Table 1-1 Dynamix DW- 1 FXS LEDs Descriptions. .........................................................4
Table 1-3 Dynamix DW- FXS 02 LEDs Functions .............................................................5
Table 1-4 LEDs Functions ...................................................................................................6
Table 2-1 Navigation Panel Links .....................................................................................14
Table 6-1 Network Interface ..............................................................................................40
Table 7-1 H323 Configuration...........................................................................................43
Table 8-1 Line Status Information .....................................................................................45
Table 9-1 Phone Book .......................................................................................................47
Table 10-1 Support Configuration .....................................................................................49
Table 11-1 System Configuration ......................................................................................51
Table 12-1 Voice Configuration.........................................................................................53
Table 13-1 Phone Configuration........................................................................................55
Table 14-1 RTP Payload Type Configuration List.............................................................57
Table 15-1 IP Packet ToS Configuration ...........................................................................59
Table 16-1 DDNS Device Configuration ..........................................................................61
Table 17-1 Prefix Drop/Insert Configuration ....................................................................63
Table 18-1 Password Configuration ..................................................................................65
Table 19-1 Version and Information ..................................................................................67
Table 20-1 ROM Configuration.........................................................................................68
Table 21-1 Flash Clean ......................................................................................................70
Table 22-1 Commit Configuration Data ............................................................................71
Table 23-1 Reboot VoIP Gateway......................................................................................72
Table 24-1 Commands with Gateway................................................................................93
List of Table
VIII
FXS H.323 VoIP Gateway User Manual
Preface
Congratulations on your purchase of the Dynamix DW FXS VoIP Gateway.
¤ About this User’s Manual
This user’s guide gives hardware specifications and explains web configuration and
command line configuration for the Dynamix DW- 1 FXS , Dynamix DW- FXS 02, and
Dynamix DW- FXS 04.
¤ General Syntax Conventions
¤ Mouse action sequences are denoted using a comma. For example, click start, Settings,
Control Panel, Network means first you click Start, Click or move the mouse pointer over
Settings the click or move the mouse pointer over Control Panel and finally click (or
double-click) Network.
¤ “Enter” means for your to type one or more characters.
¤ Naming Conventions
¤ “Dynamix DW- 1 FXS ” Gateway provides one Phone port and four Ethernet Port.
¤ “Dynamix DW- FXS 02” Gateway provides two Phone port and two Ethernet Port.
¤ “Dynamix DW- FXS 04” Gateway provides four Phone port and two Ethernet Port.
¤ Related Documentation
¤ This user’s guide provides hardware connection details and configuration and
management instruction for the managements VoIP Gateway.
IX
FXS H.323 VoIP Gateway User Manual
Part I:
VoIP Gateway Overview
This part introduces the general features default settings and hardware of the VoIP Gateway.
-1-
FXS H.323 VoIP Gateway User Manual
Chapter 1
Dynamix DW FXS VoIP
Gateway Overview
The chapter introduces the VoIP Gateway general feature, factory default settings and hardware.
1.1
VoIP Gateway Overview
VoIP Gateway, which based on ITU-T H.323 v3, provides voice and fax over IP networks. Its
simplified operation and configuration features are the most suitable for residential and SOHO
application. There are four models for VoIP Gateway, which are Dynamix DW- 1 FXS,
Dynamix DW- FXS 02, and Dynamix DW- FXS 04. One more added switch hub for A
series is the only difference. User can choose 2 ports or 4 ports as request in A series. Just an
IP address and 2/4 phone sets bring you to Voice over IP world.
1.2
Features of The VoIP Gateway
¤ VoIP Gateway Features


ITU-T H.323 v4 compliance
Ethernet:
m Dynamix DW- 1 FXS : Four 10/100 Base-T Ethernet RJ45 ports (Auto LAN MDI/
MDIX).

















m Dynamix DW- FXS 02 /Dynamix DW- FXS 04: Two 10/100 Base-T Ethernet
ports
Configuration interface: RS-232, TELNET and HTTP web management
Automatic Gatekeeper Discovery
Dimensions:
m Dynamix DW- 1 FXS : 165(W) x 29(H) x 139mm(D)
m Dynamix DW- FXS 02/Dynamix DW- FXS 04: 222(W) x 34(H) x 143mm(D)
Transmit Voice and T.38 fax simultaneously
Support T.38 ECM function (Error Correction in high speed fax Mode)
Provides call progress tone
E.164 Common Dial Plan
DTMF Dialing
Inband/Outband DTMF
TFTP/FTP software upgrade
Remote configuration/reset
LED indication for system status
Support Static IP, DHCP and PPPoE
Set the ring back tone from the IP or local
FAX redundancy support
RAS and Signal port exchangeable
GK id support and GK auto discovery
-2-
FXS H.323 VoIP Gateway User Manual
¤ Audio feature










Codec: G.711 a/µlaw, G.723.1 (6.3kbps), G.729A, G.729B, G.729AB
VAD (Voice Activity Detection)
CNG (Comfort Noise Generate)
G.168/165-compliant adaptive echo cancellation
Dynamic Jitter Buffer
Bad Frame Interpolation
Voice/DTMF Gain Settings
Generate Caller ID (DTMF or FSK)
Provide In-band or Out-band DTMF generation/detection
Provide Progress tone
¤ System Monitoring

System status (Link, Ready, Status, TEL, Power).
¤ Remote Firmware Upgrade
You can use FTP/TFTP to perform configuration backup/restore and firmware upgrade for
the VoIP Gateway from a remote location.
¤ Security


1.3
Password protection for system management
VLAN
Default Settings
The following are the settings of the defualt profile
 Login: root
 Password: Null (default)
1.3.1




1.3.2


1.4
IP Parameters
IP Address = 10.1.1.3
Subnet mask = 255.0.0.0
Default gateway = 10.1.1.254
LAN IP address = 192.168.123.123 (Only Dynamix DW- 1 FXS )
Telnet and Web Login Password
Login = root
Password = Null (default)
Front Panels
The LEDs on the front panel indicate the operational status of the Gateway.
Figure 1-1 Dynamix DW- 1 FXS Gateway Front Panel
-3-
FXS H.323 VoIP Gateway User Manual
The LEDs on the front panel indicate the operational status of the Gateway.
Figure 1-2 Dynamix DW- FXS 02 Gateway Front Panel
Figure 1-3 Dynamix DW- FXS 04 Gateway Front Panel
1.5
Back Panel Ports
Figure 1-4 Dynamix DW- 1 FXS Gateway Back Panel Ports
Figure 1-5 Dynamix DW- FXS 02 Gateway Back Panel Ports
Figure 1-6 Dynamix DW- FXS 04 Gateway Back Panel Ports
1.6
Hardware Specifications
These are the hardware details of the Dynamix DW- FXS 02, Dynamix DW- FXS 04.
1.6.1
Dynamix DW- 1 FXS LEDs
The following table describes the LED functions:
LEDs
Power
TEL
Table 1-1 Dynamix DW- 1 FXS LEDs Descriptions
Functions
Indicator
Active
Description
Status
Power
TEL
Green
Red
On
The Power adapter is connected to the
Gateway.
Off
The system is off or not receiving power.
On
The Telephone is Off-Hook.
-4-
FXS H.323 VoIP Gateway User Manual
LEDs
Ready
Functions
Ready
Indicator
Status
Green
Active
Description
Off
The Telephone is On-Hook.
Slow
Blinking
The VoIP Gateway is in normal mode.
Fast Blinking The VoIP Gateway is in downloading
mode.
Status
Status
Green
Off
The VoIP Gateway is in Peer-to-Peer
Mode.
On
The VoIP Gateway has successfully
registered to Gatekeeper when it is in
Gatekeeper mode.
Blinking
The VoIP Gateway is not registered to
Gatekeeper when it is in Gatekeeper
mode.
The VoIP Gateway is in downloading
mode.
Active
Blinking
Ethernet data is being
transmitted/received.
100/10
Link
LAN
LAN
Green
Green
On
The 100M LAN is connected.
Off
The 10M LAN is connected.
On
The VoIP Gateway is physically
connected to the Ethernet correctly.
Full/HLF
Full/HLF
DPX
DPX
Green
On
Light on means current transmitting
mode is full duplex.
Off
Light off means half-duplex.
1.6.2
Dynamix DW- FXS 02 LEDs
The following table describes the LED functions:
LEDs
Table 1-2 Dynamix DW- FXS 02 LEDs Functions
Functions
Indicator
Active
Description
Status
LAN
Link/ACT
Switch to another device, such as PC
Link/ACT
Green
Blinking
While plugging on the Ethernet cable, it
must light on and the flash if some data is
being TX/RX.
10/100M
LAN
Green
OFF
The Ethernet cable is not connected.
Off
The 10M LAN is connected.
-5-
FXS H.323 VoIP Gateway User Manual
LEDs
Functions
Indicator
Status
Active
On
WAN
Link/ACT
Description
The 100M LAN is connected.
Uplink to the HUB/Router directly.
Link/ACT
Green
Blinking
While plugging on the Ethernet cable, it
must light on and the flash if some data is
being TX/RX.
10/100M
Ready
WAN
Ready
Green
Green
OFF
The Ethernet cable is not connected.
Off
The 10M WAN is connected.
On
The 100M WAN is connected.
Slow
Blinking
The VoIP Gateway is in normal mode.
Fast Blinking The VoIP Gateway is in downloading
mode.
Status
Status
Green
Off
The VoIP Gateway is in Peer-to-Peer
Mode.
On
The VoIP Gateway has successfully
registered to Gatekeeper when it is in
Gatekeeper mode.
Blinking
The VoIP Gateway is not registered to
Gatekeeper when it is in Gatekeeper
mode.
The VoIP Gateway is in downloading
mode.
TEL(1-2)
Power
TEL
Power
Red
Green
On
The Telephone is Off-Hook.
Off
The Telephone is On-Hook.
On
The Power adapter is connected to the
Gateway.
Off
The system is off or not receiving power.
1.6.3
Dynamix DW- FXS 04 LEDs
Table 1-3 LEDs Functions
LEDs
Functions
Indicator
Active
Status
LAN
Link/ACT
Description
Switch to another device, such as PC
Link/ACT
Green
Blinking
While plugging on the Ethernet cable, it
must light on and the flash if some data is
being TX/RX.
-6-
FXS H.323 VoIP Gateway User Manual
LEDs
10/100M
Functions
LAN
Indicator
Status
Green
Active
OFF
The Ethernet cable is not connected.
Off
The 10M LAN is connected.
On
The 100M LANis connected.
WAN
Link/ACT
Description
Uplink to the HUB/Router directly.
Link/ACT
Green
Blinking
While plugging on the Ethernet cable, it
must light on and the flash if some data is
being TX/RX.
10/100M
Ready
WAN
Ready
Green
Green
OFF
The Ethernet cable is not connected.
Off
The 10M WAN is connected.
On
The 100M WAN is connected.
Slow
Blinking
The VoIP Gateway is in normal mode.
Fast Blinking The VoIP Gateway is in downloading
mode.
Status
Status
Green
Off
The VoIP Gateway is in Peer-to-Peer
Mode.
On
The VoIP Gateway has successfully
registered to Gatekeeper when it is in
Gatekeeper mode.
Blinking
The VoIP Gateway is not registered to
Gatekeeper when it is in Gatekeeper
mode.
The VoIP Gateway is in downloading
mode.
TEL(1-4)
Power
1.6.4
TEL
Power
Red
Green
On
The Telephone is Off-Hook.
Off
The Telephone is On-Hook.
On
The Power adapter is connected to the
Gateway.
Off
The system is off or not receiving power.
Back Panel Port
¤ Ethernet Port:
Ethernet port is for connecting VoIP Gateway to network, transmit rate supports 10/100
Base-T.
-7-
FXS H.323 VoIP Gateway User Manual
Ethernet connector LAN
¤ COM Port:
RS232 console port (DB-9pin male connector)
Note: use straightforward cable to connect to your computer.
PINOUTS
Pin Name Dir
Description
2
RXD
Receive Data
3
TXD
Transmit Data
5
GND
System Ground
¤ TEL Port:
RJ-11 connector, FXS interface. To connect analog phone sets or trunk line of PABX.
¤ 12V DC Port:
DC Power supply.
1.6.5
Back Panel Connections
This section outlines how to connect your VoIP Gateway to the LAN and the WAN. In the
case of connecting a Cable Modem you must connect the coaxial cable from your cable service
to the threaded coaxial cable connect on the back of the cable modem.
Step 1. Connecting the Console Port
For the initial configuration of your VoIP Gateway, you need to use terminal emulator
software on a workstation and connect it to the VoIP Gateway the console port. Connect the 9-pin
end of the console cable to the console port of the VoIP Gateway and the other end to a serial port
-8-
FXS H.323 VoIP Gateway User Manual
(COM1, COM2 or other COM port) of your workstation. You can use an extension RS-232 cable
if the enclosed one is too short. After the initial setup, you can modify the configuration remotely
through telnet connections.
Step 2. Connect the VoIP Gateway to the WAN port
Connect the WAN port (silver) on the VoIP Gateway to the Ethernet port on the cable
modem using the cable that came with your cable modem. The Ethernet port on the cable modem
is sometimes labeled “PC” or “Workstation”.
Step 3. Connecting the PC to the LAN
If you have more than one PC, you must use an external hub. Connect the 10/100M LAN
Port (gold) on the VoIP Gateway to a port on the hub using a straight through Ethernet cable. If
you only have one PC, you can connect the VoIP Gateway to the PC directly without a hub. For a
single PC, connect the 10/100M LAN port on the VoIP Gateway to the Network Adapter on the
PC using a crossover cable (red tag).
Step 4. Connecting the Power Adapter to your VoIP Gateway
Connect the power adapter to the port labeled POWER on the rear panel VoIP Gateway.
Caution: To prevent damage to the VoIP Gateway, first make sure you have the correct
AC power adapter. Please see the Appendices for AC power adapter specifications for
your region.
Step 5. Grounding the VoIP Gateway
If you want to ground the VoIP Gateway then connect a grounded wire to the F.G. (Frame
Ground) of the VoIP Gateway.
1.7
Additional Installation Requirements
In addition to the contents of your package, there are other hardware and software
requirements you need before you can install and use your VoIP Gateway. These requirements
include:
1.
2.
A computer with an Ethernet NIC (Network Interface Card) installed.
A computer equipped with communications software configured to the following
parameters:
m VT100 terminal emulation.
m 9600 Baud.
m No parity, 8 Data bits, 1 stop bit, Flow Control set to None.
3.
4.
5.
Use Internet Explorer 5.5 and later or Netscape Navigator 6 and later versions.
Analog telephone set
Software tools: Gatekeeper (optional)
After the VoIP Gateway is properly set up, you can make future changes to the
configuration through telnet connections
1.8
Setting Up the TCP/IP Protocol
If you are not sure whether the TCP/IP Protocol has been installed, follow these setups to
check, and if necessary, install TCP/IP onto your PCs.
-9-
FXS H.323 VoIP Gateway User Manual
Step 1. Click the [Start] button, Choose [Settings], then [Control Panel]. Double-click the
[Network] icon. Your Network window should appear as follows.
Step 2. Select the [Configuration] tab.
Import:
For Windows 2000 & Windows XP Setting, you will find that they differs with Windows
98/ME/NT slightly. See the Following for reference.
Click the “Local Area Connection” icon on the lower right hand side of your desktop
screen.
In the [Local Area Connection Status] windows, click the [Properties] button the your
Network windows will appear.
There is only one tab, [General], in the Network window.
Step 3. Click whether the TCP/IP Protocol has already been installed onto your computer’s
Ethernet card. Note that TCP/IP Protocol an be installed for a computer’s Dial-Up Adapter
as well as for the Ethernet cad.
- If yes, go to set 7.
- If no, click the [Add] button
Step 4. Double-click [Protocol] in the Select Network Component Type or highlight [Protocol]
then click [Add].
Step 5. Highlight [Microsoft] under the list of manufactures
Step 6. After a new second, you will be returned to the Network window. The TCP/IP Protocol
should now be on the list of installed network components.
Step 7. Click the [Properties] button. The TCP/IP Properties windows consist of several tabs.
Choose the [IP Address] tab.
Step 8.
Select [Specify an IP Address] and enter [10.1.1.1] in the [IP Address] location (where
xxx is a number between 2 and 254 used by the VoIP Gateway to identify each computer),
and the default [Subnet Mask: 255.0.0.0]. Note than no two computers on the same LAN
can have the same IP address.
Step 9. Click on the [DNS Configuration] tab and select [Enable DNS]. Then click the [Add]
button.
Step 10. Click on the [Gateway] tab and enter the High-Performance VoIP Gateway default
gateway value 10.1.1.254 in the [new gateway] field, then click [Add] Button.
Step 11. Click [OK] button, Restart your PC to complete the TCP/IP installation.
1.9
Power Up Your VoIP Gateway
At this point, you should have connected the console port, the LAN Port, the WAN port and
the power port to the appropriate devices or lines. Plug the power adapter into a wall outlet. The
Power LED should be on. The Status LED will come on after the system tests are complete. The
WAN LED and one of the LAN LEDs come on immediately after the Status LED come on, if
connections have been made to the LAN and WAN ports.
- 10 -
FXS H.323 VoIP Gateway User Manual
Part II:
Web Configuration with VoIP Gateway
This part tells how to access and navigate the web configurator and perform initial configuration. It
also describes the Getting Started web configuration when you use the VoIP Gateway.
- 12 -
FXS H.323 VoIP Gateway User Manual
Chapter 2
Web Configuration with FXS Introduction
This Chapter describes how to login into the WEB and navigate through it.
2.1
Web Configuration with FXS Overview
The embedded web configuration allows you to use a web browser to manage the VoIP
Gateway.
2.2
Accessing the Web Configuration
You will need a computer with and Ethernet 10BaseT, 100Base-TX Network Interface Card
(NIC). Connect to the LAN port in the FXS.
Use Internet Explorer 5.5 and later or Netscape Navigator 6 and later versions.
Use the following instructions to login on to the web configuration.
2.3
Login and welcome screen
Step 1.
Step 2.
Start your web browser.
Launch your web browser and enter [10.1.1.3] (the default IP address of the VoIP
Gateway) in the Location or Address field. Press Enter.
Step 3. The Password screen now appears. Type [root] in the user name field (it may display
automatically for you) and your password (default [Null]) in the password field.
Step 4.
Click OK.
Step 5.
After a successful login, you will see the welcome screen show next.
2.4
Welcome Screen
This is the web configuration welcome screen. Click a link on the navigation panel to go to
the corresponding screen.
- 13 -
FXS H.323 VoIP Gateway User Manual
Figure 2-1 VoIP Gateway web configuration welcome screen
The following table describes the screen.
LABEL
Network Interface
Table 2-1 Navigation Panel Links
DESCRIPTION
This link takes you to a screen where you can configure the VoIP Gateway
Network Interface Information.
- 14 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
H323 Information
This link takes you to a screen where you can setup up H323 Information.
Line Status
This link takes you to a screen. When will set hotline, no answer forward;
understand Line registration and use status of the VoIP Gateway.
Phone Book
This link takes you to a screen where you can set up Phone Book
Information.
Support Configuration This link takes you to a screen where you can set up Support Functions
Configuration.
System Configuration This link takes you to a screen where you can set up System Configuration.
Voice Setting
This link takes you to a screen where you can set up Voice Configuration.
Phone Configuration This link takes you to a screen. When will set phone patterns of the VoIP
Gateway.
RTP Payload Type
configuration
This link takes you to a screen. When will set RTP Payload Type patterns
of the VoIP Gateway.
IP Packet ToS
This link takes you to a screen. When will set IP Pack ToS of the VoIP
Gateway.
DDNS Configuration This link takes you to a screen. When will use DDNS of the VoIP Gateway.
Prefix Configuration This link takes you to a screen. When will set prefix number of the VoIP
Gateway.
Version and
Information
This link takes you to a screen. When will understand Version and
Information of the VoIP Gateway.
Password
This link takes you to a screen. When will change passwords.
ROM Upgrade
This link takes you to a screen. When will change ROM Upgrade
configuration.
Flash Clean
This link takes you to a screen. When will clean flash memory information
back to factory setting.
Commit Data
This link takes you to a screen. When will save your changes to the
non-volatile memory.
Reboot System
This link takes you to a screen. When will reboot VoIP Gateway.
FXSO Gateway Only FXO Gateway special setting. Only use FXO port can set.
Route Table
This link takes you to a screen. When will set Routing Table is a rule to
define the destination of the calls you make (FXO Gateway only).
Tone Configuration
This link takes you to a screen. When will set Tone pattern (FXO Gateway
only).
FXO Password
This link takes you to a screen. When will set use FXO password (FXO
Gateway only).
2.5
Saving Your Configuration
Click OK to save your changes back to the VoIP Gateway volatile memory. The VoIP
- 15 -
FXS H.323 VoIP Gateway User Manual
Gateway loses these changes if it is turned off or loses power, so use the Commit Data link on the
navigation panel to the left to save your changes to the non-volatile memory when your are done
configuring.
2.6
Navigating the Web Configuration
The web configuration uses one level. For example, to configure [Network Interface], click
the link on the navigation panel to open the configuration screen.
Figure 2-2 Network Interface Screen
- 16 -
FXS H.323 VoIP Gateway User Manual
Chapter 3
Initial Configuration
This Chapter covers the basic configuration needed to set up and use the VoIP Gateway. Refer to
the other part describes about individual fields within screens.
3.1
Initial Configuration Overview
This chapter describes the procedure for the initial configuration of the VoIP Gateway.
Refer to the relevant chapters in this User’s Guide for descriptions of the fields and buttons
within individual screens.
3.2
General Configuration
The VoIP Gateway the factory with a default IP address of 10.1.1.3 and a subnet mask of
255.0.0.0, default gateway of 10.1.1.254.
3.3
Static IP address
Step 1.
Configuration the VoIP Gateway IP address. Click [Network Interface] on the
navigation panel. In the Network Interface screen, type a new IP address, subnet mask and
the default routing gateway (e.g. IP Address: 192.168.13.80, Subnet mask: 255.255.248.0,
Default routing gateway: 192.168.8.254) and click the OK button.
- 17 -
FXS H.323 VoIP Gateway User Manual
Figure 3-1 Network Interface
Step 2. Click [Commit Data] on the navigation panel. In the Commit Configuration Data
screen, click the [Commit] button. In the Commit Configuration Data screen to Display
[Commit to Flash OK!], When the Commit Data Ok.
Figure 3-2 Commit Configuration Data
Step 3. Click [Reboot System] on the navigation panel. In the VoIP Gateway screen, click the
[Reboot] button. It will take 40 seconds to reboot.
- 18 -
FXS H.323 VoIP Gateway User Manual
Figure 3-3 Reboot VoIP Gateway
Step 4. Close the current browser windows and launch your web browser again. Enter the new
IP address in the Location or Address field.
3.4
DHCP mode
Step 1.
Configuration the VoIP Gateway IP address for DHCP Mode. Click [Network
Interface] on the navigation panel. In the Network Interface screen, enable the DHCP
function if you are using the cable modem or DHCP server and click the [OK] button.
- 19 -
FXS H.323 VoIP Gateway User Manual
Figure 3-4 Network Interface
Step 2. Click [Commit Data] on the navigation panel. In the Commit Configuration Data
screen, click the Commit button. In the Commit Configuration Data screen to Display
[Commit to Flash OK!], When the Commit Data Ok.
Step 3.
Click [Reboot System] on the navigation panel. In the VoIP VoIP Gateway screen,
click the [Reboot] button. It will take 40 seconds to reboot.
Step 4. Close the current browser windows and launch your web browser again. Enter the new
IP address in the Location or Address field.
3.5
PPPoE mode
Step 1. Configuration the VoIP Gateway IP address for PPPoE Mode. Click [Network
Interface] on the navigation panel. In the Network Interface screen, Select IP mode: PPPoE,
- 20 -
FXS H.323 VoIP Gateway User Manual
and put the info of the PPPoE User Name, password, and Reboot After Remote Host
Disconnection: Enable (e.g. User: 123456@hinet.net, password: 123456) and click the [OK]
button.
Figure 3-5 PPPoE Device Configuration
Step 2. Click [Commit Data] on the navigation panel. In the Commit Configuration Data
screen, click the Commit button. In the Commit Configuration Data screen to Display
- 21 -
FXS H.323 VoIP Gateway User Manual
[Commit to Flash OK!], When the Commit Data Ok.
Step 3.
Click [Reboot System] on the navigation panel. In the VoIP VoIP Gateway screen,
click the [Reboot] button. It will take 40 seconds to reboot.
Step 4. Close the current browser windows and launch your web browser again. Enter the new
IP address in the Location or Address field. .
3.6
IP Sharing Configuration
The function is only for the user who is using the IP Sharing device. It is said Gateway is
connected to the IP Sharing device.
The IP Sharing Device must support the DMZ or Virtual server functions
An e.g. such as ADSL network is in the following.
- 22 -
FXS H.323 VoIP Gateway User Manual
Step 1. The WAN IP Address obtained from ADSL has two kinds of methods.
Step 2. One is fixed IP Address, while user applies for one or more fixed IP Addresses.
Step 3. Another is dynamic IP Address while user applies for dial-up connection way. The
LAN IP Address of User’s PC can be set as DHCP client in order to gain a valid one.
Step 4. Another IP Address for Gateway must be set as an fixed one in order for that IP
Sharing device pass forwarding the relevant information from WAN to LAN. Besides, a
valid IP Address meets the IP Sharing device (LAN site) is the element.
Step 5.
VoIP Gateway must enable the IP Sharing function for the fixed/dynamic WAN IP
Address.
Note:
With Dynamic WAN IP Address, a valid Gatekeeper for VoIP Gateway to get register
on is a must. In other word, it is not workable in Peer-to-Peer mode while dynamic WAN IP
Address.
Step 6. IP Sharing device must have a function to do IP/Port mapping. Some is named as DMZ,
some is named as virtual server whatever. The VoIP messages from WAN have to
completely pass forward to the LAN. It is said if the VoIP Gateway is assigned a virtual
fixed IP Address such as 192.168.1.5, IP Sharing device must forward the VoIP message to
192.168.1.5.
Step 7.
Configuration the VoIP Gateway IP address for IP Sharing Mode. Click [Network
Interface] on the navigation panel. In the Network Interface screen, enter the IP address,
Subnet mask and the default gateway in the network table. Please follow up your IP Sharing
device
Step 8. Enable the IP sharing function and put the static IP address in the IP Sharing server
address (e.g. 210.59.163.198) and click the OK button.
- 23 -
FXS H.323 VoIP Gateway User Manual
Figure 3-6 Enable the IP sharing function
Step 9. Click [Commit Data] on the navigation panel. In the Commit Configuration Data
screen, click the Commit button. In the Commit Configuration Data screen to Display
[Commit to Flash OK!], When the Commit Data Ok.
Step 10. Click [Reboot System] on the navigation panel. In the VoIP Gateway screen, click the
[Reboot] button. It will take 40 seconds to reboot.
Step 11. Close the current browser windows and launch your web browser again. Enter the new
IP address in the Location or Address field.
3.7
PPPoE (NAT) mode (1A-FXS)
- 24 -
FXS H.323 VoIP Gateway User Manual
Step 1.
Configuration the VoIP Gateway IP address for PPPoE Mode. Click PPPoE
Configuration on the navigation panel. In the PPPoE Configuration screen, On the Device
and put the info of the PPPoE User Name and password (e.g. User: 123456@hinet.net,
password: 123456) and click the OK button.
Step 2.
Figure 3-7 PPPoE Device Configuration
Click Commit Data on the navigation panel. In the Commit Configuration Data screen,
- 25 -
FXS H.323 VoIP Gateway User Manual
click the Commit button. In the Commit Configuration Data screen to Display Commit to
Flash OK!, When the Commit Data Ok.
Step 3. Click [Reboot System] on the navigation panel. In the VoIP Gateway screen, click the
[Reboot] button. It will take 40 seconds to reboot.
Step 4. Close the current browser windows and launch your web browser again. Enter the new
IP address in the Location or Address field.
Step 5.
Setup PC use LAN IP connection Network
Select [Specify an IP Address] and enter [192.168.123.111] in the [IP Address] location
(where xxx is a number between 2 and 254 used by the VoIP Gateway to identify each
computer), and the default [Subnet Mask 255.255.255.0]. Note than no two computers on
the same LAN can have the same IP address. VoIP Gateway default gateway value
192.168.123.123 in the [new gateway] field. Then save your change.
- 26 -
FXS H.323 VoIP Gateway User Manual
Chapter 4
Making a VoIP Call
This Chapter covers the basic configuration the gateway for making VoIP calls. One is the
Peer-to-Peer mode, another is GK routed mode. The configurations and functions are different.
Please make sure about the mode you want and follow up the step to configure your gateway.
4.1
Configure the gateway into the Peer-to-Peer mode
Step 1. Configuration the VoIP Gateway H323 Configuration. Click [H323 Configuration] on
the navigation panel. In the H323 Configuration screen, select Peer-to-Peer Mode function,
set line number (e.g. Line1 Number 3001, Line2 Number: 3002) and click the [OK] button.
- 27 -
FXS H.323 VoIP Gateway User Manual
Step 2.
Figure 4-1 H323 Configuration – Peer to Peer mode Screen
Configuration the VoIP Gateway Phone Book. Click [Phone Book] on the navigation
panel. In the Phone Book screen, enter the Index, Name, IP address and e164 (phone
number) of the destination and click the Add Data button.
Figure 4-2 Phone Book
Step 3. E.g. enter the Index: 1, Name: test1, e164 No.: 20, IP address: 192.168.13.80 and of
the destination and click the [Add Data] button.
- 28 -
FXS H.323 VoIP Gateway User Manual
Step 4.
Figure 4-3 Phone Book – New Record
On table will display on the first index.
Figure 4-4 Phone Book
Step 5. Click [Commit Data] on the navigation panel. In the Commit Configuration Data
screen, click the [Commit] button. In the Commit Configuration Data screen to Display
[Commit to Flash OK!], When the Commit Data Ok.
- 29 -
FXS H.323 VoIP Gateway User Manual
Step 6.
Click [Reboot System] on the navigation panel. In the VoIP VoIP Gateway screen,
click the [Reboot] button. It will take 40 seconds to reboot.
4.2
Configure the gateway into the GK routed mode
4.2.1
Gateway Type: Gateway
Step 1. Configuration the VoIP Gateway H323 Configuration. Click [H323 Configuration] on
the navigation panel. In the H323 Configuration screen, select GK routed Mode function.
Step 2. To change the GK information from your service provider Gatekeeper IP, 2nd
Gatekeeper IP, Gateway Type, Registered Prefix, Line1 Number, Line 2 Number, Line 3
Number and Line 4 Number (e.g. Gatekeeper IP: 192.168.13.71, 2nd Gatekeeper IP:
192.168.13.71, Gateway Type: Gateway, Registered Prefix: 300, Line1 Number: 3001,
Line2 Number: 3002, Line3 Number: 3003, Line 4 Number: 3004), and click the [OK]
button.
- 30 -
FXS H.323 VoIP Gateway User Manual
Step 3.
Figure 4-5 Configure the GK info
Click Commit Data on the navigation panel. In the Commit Configuration Data screen,
click the Commit button. In the Commit Configuration Data screen to Display [Commit to
Flash OK!], When the Commit Data Ok.
Step 4. Click [Reboot System] on the navigation panel. In the VoIP VoIP Gateway screen,
click the [Reboot] button. It will take 40 seconds to reboot.
4.2.2
Gateway Type: Terminal
Step 1. Configuration the VoIP Gateway H323 Configuration. Click [H323 Configuration] on
the navigation panel. In the H323 Configuration screen, select GK routed Mode function.
Step 2. To change the GK information from your service provider Gatekeeper IP, 2nd
Gatekeeper IP, Gateway Type, Line1 Number, Line 2 Number (e.g. Gatekeeper IP:
192.168.13.71, 2nd Gatekeeper IP: 192.168.13.71, Gateway Type: Terminal, Line1
Number: 3001, Line2 Number: 3002, Line3 Number: 3003, Line 4 Number: 3004), and
click the [OK] button.
- 31 -
FXS H.323 VoIP Gateway User Manual
Step 3. Click Commit Data on the navigation panel. In the Commit Configuration Data screen,
click the Commit button. In the Commit Configuration Data screen to Display [Commit to
Flash OK!], When the Commit Data Ok.
Step 4. Click [Reboot System] on the navigation panel. In the VoIP VoIP Gateway screen,
click the [Reboot] button. It will take 40 seconds to reboot.
- 32 -
FXS H.323 VoIP Gateway User Manual
Chapter 5
Upgrade ROM Version
This Chapter covers the basic how to upgrade VoIP Gateway ROM Version.
5.1
Before you start downloading
Step 1.
Please confirm Host PC, which is installed as TFTP / FTP server and device is in
available network.
Step 2.
Remember the current configuration, such as [H323 Configuration] [Line
configuration], [Phone Book].
5.2
Update Application Version
Step 1.
Update the VoIP Gateway ROM Version. Click [ROM Upgrade] on the navigation
panel. In the [ROM Configuration] screen, type a Server IP address, Target File Name,
Method, Target File Type (e.g. Server IP Address: 192.168.4.71, Target File Name:
Dynamix DW- FXS 04.204, Method: TFTP, Target File Type: Application image) and click
the [OK] button.
Figure 5-1 ROM Configuration
Step 2. In the screen to Display [Please issue FLASH CLEAN to consist software version.]
information. When the ROM Upgrade file ok.
- 33 -
FXS H.323 VoIP Gateway User Manual
Figure 5-2 ROM File Upgrade ok
Step 3. Click [Flash Clean] on the navigation panel. In the Flash Clean screen, click the
[CLEAN] button.
Figure 5-3 Flash Clean
Step 4. In the Flash Clean screen to Display [Flash cleaned!! Please reboot your system!!],
When the Flash Clean Ok.
- 34 -
FXS H.323 VoIP Gateway User Manual
Figure 5-4 Flash Clean OK
Step 5. Click [Reboot System] on the navigation panel. In the Reboot VoIP Gateway screen,
click the [Reboot] button. It will take 40 seconds to reboot.
Step 6. Close the current browser windows and launch your web browser again. Enter the IP
address in the Location or Address field.
5.3
Update Boot2m Version
Step 1.
Update the VoIP Gateway 2mROM Version. Click [ROM Upgrade] on the navigation
panel. In the [ROM Configuration] screen, type a Server IP address, Target File Name,
Method, Target File Type (e.g. Server IP Address: 192.168.4.71, Target File Name:
2mDynamix DW- FXS 04.204, Method: FTP, FTP Login name: totoro, passwd: totoro,
Target File Type: 2m Boot image) and click the [OK] button.
- 35 -
FXS H.323 VoIP Gateway User Manual
Step 2. In the screen to Display [Please issue FLASH CLEAN to consist software version]
information. When the ROM Upgrade file ok.
Figure 5-5 ROM File Upgrade ok
Step 3. Click [Flash Clean] on the navigation panel. In the Flash Clean screen, click the
[CLEAN] button.
- 36 -
FXS H.323 VoIP Gateway User Manual
Figure 5-6 Flash Clean
Step 4. In the Flash Clean screen to Display [Flash cleaned!! Please reboot your system!!],
When the Flash Clean Ok.
Figure 5-7 Flash Clean OK
Step 5. Click [Reboot system] on the navigation panel. In the Reboot VoIP Gateway screen,
click the [Reboot] button. It will take 40 seconds to reboot.
- 37 -
FXS H.323 VoIP Gateway User Manual
Step 6. Close the current browser windows and launch your web browser again. Enter the IP
address in the Location or Address field.
- 38 -
FXS H.323 VoIP Gateway User Manual
Chapter 6
Network Interface Screen
This Chapter covers setup Network Interface identification information for VoIP Gateway.
6.1
Network Interface Overview
The web configuration provides Network Interface screen.
6.2
Network Interface Screen
Click [Network Interface] in the navigation panel and open the Network Interface Screen.
Use this screen to setup Network Interface identification information for the VoIP Gateway.
- 39 -
FXS H.323 VoIP Gateway User Manual
Figure 6-1 Network Interface
The following table describes this screen.
LABEL
IP Mode
Table 6-1 Network Interface
DESCRIPTION
Select use defines the networking type for this gateway. It could support
the Static, DHCP and PPPoE function.
IP Address
Enter the IP Address of the VoIP Gateway in dotted decimal notation for
e.g. 192.168.4.92. Range of IP Address setting (0.0.0.0~255.255.55.255).
Subnet Mask
Enter the IP Subnet Mask of your VoIP Gateway in dotted decimal notation
for e.g. 255.255.0.0.
Default Routing
Gateway
Enter the IP Address of the default-outgoing gateway of your VoIP
Gateway in dotted decimal notation for e.g. 192.168.1.254.
LAN Port IP for NAT Specify LAN port IP address for NAT function (Dynamix DW- 1 FXS
only).
HTTP Port
Set VoIP Gateway HTTP Port Number e.g. 80.
DNS primary
Enter the DNS IP Address in dotted decimal notation for e.g. 168.95.1.1
DNS Secondary
Enter the DNS secondary IP Address in dotted decimal notation for e.g.
168.95.1.1
SNTP
Select enable/disable Simple Network Time Protocol.
SNTP Server Address Set specifies a SNTP Server as network time source in dotted decimal
notation for e.g. 168.95.192.12.
GMT
Set local time zone according to GMT e.g. 8.
- 40 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
IP Sharing
Select enable IP Sharing function, when you specify usage of and IP
Sharing device.
IP Sharing
Address
Server Enter specify a global fixed IP Address, user can add this IP Address in
dotted decimal notation for e.g. 210.11.22.33. However, dynamic IP
Address is not working in Peer-to-Peer mode.
PPPoE User Name
Set the PPPoE connection account in this table. Please get this info from
your ISP.
PPPoE Password
Set the PPPoE connection password in this table. Please get this info from
your ISP.
PPPoE IP Address
The field display the IP address. When VoIP Gateway after the connection
success, which the gateway got from the ISP.
PPPoE Destination
The field display the default gateway address. When VoIP Gateway after
the connection success, which the gateway got from the ISP.
PPPoE DNS primary The field display the DNS IP address. When after the connection success,
will show you the DNS ip address from the ISP.
Reboot After Remote Select enable or disable this function will make the gateway restart
Host Disconnection automatically if the PPPoE connection is disconnected or the IP address
was taken back by the ISP.
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
- 41 -
FXS H.323 VoIP Gateway User Manual
Chapter 7
H323 Configuration Screen
This Chapter covers setup H.323 related parameters.
7.1
H323 Configuration Overview
The web configurator provides H.323 Configuration screen.
7.2
H323 Configuration Screen
Click [H323 Configuration] in the navigation panel and open the [H323 Configuration]
Screen.
- 42 -
FXS H.323 VoIP Gateway User Manual
Figure 7-1 H323 Configuration
The following table describes this screen.
Table 7-1 H323 Configuration
DESCRIPTION
LABEL
Mode
Select Gatekeeper routed mode or Peer-to-Peer mode.
GateKeeper IP
Address
Set Gatekeeper IP Address in dotted decimal notation e.g.192.168.4.71.
2nd GateKeeper IP
Set redundancy second 2 Gatekeeper IP Address in dotted decimal notation
e.g.192.168.4.71.
Default Gateway IP
All the calls will be routed to this destination if the destination couldn’t be
found in the Phone Book configuration. Support the Peer-to-Peer mode
only.
Gateway Type
Select registration Gateway Type is Gateway mode or Terminal mode.
Registered Prefix
Set Prefix number while registration Gateway Type is Gateway example
60 (max 20 digits).
Line1 Number
Set Line1 number e.g.601 (1~20 digits).
Line2 Number
Set Line2 number e.g.602 (1~20 digits).
Line3 Number
Set Line3 number e.g.603 (1~20 digits).
Line4 Number
Set Line4 number e.g.604 (1~20 digits).
Registered Alias
Set IP side Registration alias as h323 ID.
Display Information
Set string representing display information for repertory to the called party.
- 43 -
FXS H.323 VoIP Gateway User Manual
LABEL
Gatekeeper ID
DESCRIPTION
The name of the GK. It has used with the Gatekeeper Discovery function.
Support the GK mode only.
Gatekeeper Discovery Select Gatekeeper auto Discovery is enable/disable.
Time To Live (TTL)
Set RAS TTL Time, example 60 (0~3600 second).
RTP Port
Set RTP port number, example 16384 (1024 to 65532).
Gatekeeper finding
port
Set Gatekeeper finding port e.g.1718 (1024 to 65535).
Gatekeeper RAS Port Set Gatekeeper RAS Port e.g.1719 (1024 to 65535).
H225 RAS Port
Set H225 Call RAS Port e.g.1024 (1024 to 65535).
H225 Call Signal Port Set H225 Call Signal Port e.g.1720 (1024 to 65535).
Destination H225 Call The destination Call Signal Port. Support the GK and Peer-to-Peer mode
Signal Port
both (1024 to 65535).
Allocate Port Range
Start
The port range for this gateway (1024 to 19999).
Allocate Port Range
End
The port range for this gateway (1024 to 19999).
Response Timeout
Set max waiting time for 1st response to a new call e.g.15 (1~200).
Connection Timeout
Set max waiting times for call establishment after receiving 1st response of
a new all e.g.200 (1~20000).
H.235 Security Token Support H235 security password for the registration (1~20 digits).
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
Note:
Line1 & Line2 number must follow the prefix number if device is configured as Gateway
type. For example, if prefix number is 999, the line1 & line2 number are 9991 & 9992.
Line number field auto display data follow VoIP Gateway line port number, if you see Line
number field display [-1], you can’t set it.
- 44 -
FXS H.323 VoIP Gateway User Manual
Chapter 8
Line Configuration Screen
This chapter explains the Line Status Information Screen.
8.1
Line Configuration Overview
The web configurator provides Line Status Information screen.
8.2
Line Configuration Screen
Click [Line Configuration] in the navigation panel to open the Line Configuration]
Information screen.
Figure 8-1 Line Configuration Information
The following table describes this screen.
LABEL
Table 8-1 Line Status Information
DESCRIPTION
Line Number
This field Display the Line Number.
Type
This field Display the port type. There is only display FXS Type. It couldn’t
be changed.
Hunting Group
Define the group number of this port. When the port is busy, the call could
be transferred to another port in the same group. Only the same type could
be configured in the same group.
Hotline
Set the hotline number, the hotline mode will be enabled if you enter the
hotline number. The default setting is disabled.
- 45 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
No Answer Forward Set the port no answer will be forward other number. This is only for the
E164 number or the phone numbers you want to transfer.
Registration
This field Display the VoIP Gateway registered on the GK or not.
Status
This field Display line status is Ready or Busy.
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
Note:
Hunting Group field auto display data follow VoIP Gateway line port number, if you see
Hunting Group field display [Null], you can’t set it.
- 46 -
FXS H.323 VoIP Gateway User Manual
Chapter 9
Phone Book Configuration Screen
This Chapter covers Phone Book function allows users to define their own numbers, which
mapping to real IP address. It is effective only in peer-to-peer mode. When adding a record to
Phone Book, users do not have to reboot the machine, and the record will be effective
immediately.
9.1
Phone Book Configuration Overview
The web configuration allows you to Set up Phone Book that tell the VoIP Gateway how to
call management traffic when you configuration P2P mode.
9.2
Phone Book Configuration Screen
Click [Phone Book Configuration] in the navigation panel and open the [Phone Book]
Screen.
Figure 9-1 Phone Book
The following table describes this screen.
LABEL
Table 9-1 Phone Book
DESCRIPTION
Index
The field displays the index number.
Name
The field displays the descriptive name.
E164
The field displays the descriptive E164 number.
IP Address
The field displays the IP Address or Domain name.
- 47 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
Port
The field displays the call signal port of the destination (default: 1720).
Drop Prefix
The filed display the drop function.
Insert Prefix
The field displays the insert digits number.
New Record
Index
Set up an Index number from 1 to 100, to the parameter to show specific
phone number.
Name
Set up a descriptive name (max 20 byte).
IP Address
Set up IP Address or Domain Name.
E164
Set up e164 (telephone) number (max 20 digits)
Port
Set up the call signal port of the destination (default: 1720).
Drop Prefix
Select enable or disable drop prefix function. The function is enable means
to drop e.164 number when dialing out. The function is disable means to
keep e 164 number.
Insert Prefix
Set up the insert digits number (1~20 digits).
Add Data [button]
Click [Add Data] button to insert the information table.
Delete Date [button]
Input the index number on index filed, and then click [Delete Data] button
will to delete the record from the table.
Note:
The e164 number defined in phone book will fully carry to destination. It is not just a
representative number for destination’s IP Address. In other words, user dial this e164 number to
reach destination, destination will receive the number and find out if it is matched to its e164,
including Line number in some particular device.
- 48 -
FXS H.323 VoIP Gateway User Manual
Chapter 10
Support Configuration Screen
This Chapter provides some extra functions that might be needed by users.
10.1 Support Configuration Overview
The web configuration provides Support Configuration screen.
10.2 Support Configuration Screen
Click [Support configuration] in the navigation panel and open the [Support Configuration]
Screen.
Figure 10-1 Support Configuration
The following table describes this screen.
Table 10-1 Support Configuration
LABEL
T.38 FAX
DESCRIPTION
Select enable/disable for T.38 FAX function. When T.38 ability is on, VoIP
Gateway will automatically defer codec (G.723 or G.729a) to T.38 when
FAX signal is detected.
T.38 FAX ECM
Select enable/disable for T.38 FAX ECM function. Support the error
correction in the high speed fax mode
T.38 FXS ASN.1
Select enable/disable for T.38 FXS ASN.1. Support the ASN.1 function.
Fax Redundancy
Depth
Select enable/disable for Fax Redundancy Depth. This support function
could make the data for the FAX sending for twice. But this will take more
- 49 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
bandwidth (0~2).
Fast Start
Select enable/disable for Fast Start function. Fast Start function can
shorten the connection time if the opposite party also supports Fast Start.
H.245 Tunneling
Select enable/disable for H.245 Tunneling function. If the function is on,
VoIP Gateway will send H.245 (Call Control messages) via H.225’s (Call
Signal messages) link. The function is effective only when both side
support h245 tunnel.
H.245 Message After Select enable/disable for H.245 Message After Fast Start function. If the
Fast Start
function is ON, VoIP Gateway will send H.245 messages after Fast Start.
Early H.245
Select enable/disable for Early H.245 Message. The function is effective
only when both sides support early H.245.
H.450
Select enable/disable for H450 related features, which include transfer,
hold and forward.
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
Note:
It is not recommended to change the value in this web, only if users do know well the
application. This might cause incompatibility with other devices.
- 50 -
FXS H.323 VoIP Gateway User Manual
Chapter 11
System Configuration Screen
This Chapter covers System Information and configuration.
11.1 System Configuration Overview
The web configuration provides System Configuration screen.
11.2 System Configuration Screen
Click [System Configuration] in the navigation panel and open the [System Configuration]
Screen.
Figure 11-1 System Configuration
The following table describes this screen.
LABEL
Table 11-1 System Configuration
DESCRIPTION
Inter Digit Time
The call will be sent out if user didn’t enter the digits after this timer. From
1 to 10.
Forward time
It supports the No Answer Forward function. If users configure it for 10,
the call will be forwarded when it rings about 10 seconds. From 5 to 65535.
Keypad Type
Select In-Band: The DTMF signal sending by RTP. Out-Band: The DTMF
signal sending not by RTP. Including the H.245 (Alpha), H.245 (Signal),
Q.931 and RFC 2833.
User defined Prefix
Select on/off for User defined local zone prefix switch. If user enables
- 51 -
FXS H.323 VoIP Gateway User Manual
LABEL
Switch
DESCRIPTION
prefix function, once user dials out, gateway will automatically add prefix
number before number user dialed.
User defined Prefix
Disable
Disable the defined prefix after press the selected digit (0,1~9, *)
User defined Prefix
This will be added in the first digits of the numbers that users had dialed.
Can also define IP address here in P2P mode, once user press “#”, Gateway
will call out this IP address.
Ring Time
(FXS+FXO)
It for the ring detection from the PSTN. The ring detection will be failed if
Ring Before Answer
(FXS+FXO)
This will help the users to answer the calls from PSTN into this gateway
users configure it too long (FXO Only).
quickly. The call will be connected by one time ring if users configure this
for 1. From 1 to 10 (FXO Only).
Codec Select Method This could support that the codec will follow the MSD (Master Slave
Determination) or the caller side. Master: Follow the result from the
Master Slave Determination. Caller: Follow the caller side.
Local Generate Ring To enable or disable the ring back tone generation from the local side.
Back Tone
End of Dial
To enable or disable the end of dial function. This function key will be the
digit “#”.
Gateway Prefix
To keep or drop the prefix number of this gateway. This only support the
Gateway type in the GK routed mode.
FXO Type
(FXS+FXO)
Users could configure the entire calls need the 2nd stage dialing or not.
Normal: The 1st or 2nd stage dialing will depend on the dialing plan from
the users. If user dial the number of the FXO port, that will be the 2nd stage
dialing. Force 2nd dial: Every call will need the 2nd stage dialing type
(FXO Only).
Hardware Type
(FXS+FXO)
Set the hardware detection type, select auto detect/ 1FXS+1FXO/
2FXS+2FXO mode (FXO Only).
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
Note:
The default value is to auto detect hardware type. Usually it is not necessary to change this setting.
Please make sure about your Hardware Type, Gateway may be not functional if set
wrong hardware type.
- 52 -
FXS H.323 VoIP Gateway User Manual
Chapter 12
Voice Configuration Screen
This Chapter covers voice is associated with the audio setting information.
12.1 Voice Configuration Overview
The web configuration provides Voice Configuration screen.
12.2 Voice Configuration Screen
Click [Voice Configuration] in the navigation panel and open the [Voice Configuration]
Screen.
Figure 12-1 Voice Configuration
The following table describes this screen.
LABEL
Table 12-1 Voice Configuration
DESCRIPTION
Codec Priority
Set priority preference of installed codes, G.723, G.711A, G.711U, G.729,
G.729A, G.729B, G.729AB.
Frame Size
Set Specify sending packet size, G.723: 30/60/90, G.711A, G.711U, G.729,
G.729A, G.729B, G.729AB: 20/40/60ms.
The smaller the packet size, the shorter the delay time. If network is in
good condition, smaller sending packet size is recommended.
Line1/
TEL1 Volume
Set voice volume stands for volume, which can be heard from VoIP
Gateway side (0~63, default: 28).
- 53 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
Set input gain stands for volume, which the opposite party hears (0~38,
default: 28).
Set dtmf volume stands for DTMF volume/level (0~31, default: 23).
Line2/
Line1 Volume
Set voice volume stands for volume, which can be heard from VoIP
Gateway side (0~63, default: 28).
Set input gain stands for volume, which the opposite party hears (0~38,
default: 28).
Set dtmf volume stands for DTMF volume/level (0~31, default: 23).
Line3/
TEL2 Volume
Set voice volume stands for volume, which can be heard from VoIP
Gateway side (0~63, default: 28).
Set input gain stands for volume, which the opposite party hears (0~38,
default: 28).
Set dtmf volume stands for DTMF volume/level (0~31, default: 23).
Line4/
Line2 Volume
Set voice volume stands for volume, which can be heard from VoIP
Gateway side (0~63, default: 28).
Set input gain stands for volume, which the opposite party hears (0~38,
default: 28).
Set dtmf volume stands for DTMF volume/level (0~31, default: 23).
G723 Silence
Suppression
Select enable/disable for G723 silence suppression and comfort noise
generation setting.
Echo Canceller
Setting enable/disable of echo canceller.
Jitter Buffer
Setting of jitter buffer min/max delay.
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
Note:
Well the application before you change voice parameters, because this might cause
incompatibility.
- 54 -
FXS H.323 VoIP Gateway User Manual
Chapter 13
Phone Configuration Screen
This Chapter covers VoIP Gateway progress tone is configurable. Default tone value is set
according to U.S. tone specification. Users may adjust the values according to their own
country’s tone specification or users-defined tone specification.
13.1 Phone Configuration Overview
The web configurator provides [Phone Configuration] screen.
13.2 Phone Configuration Screen
Click [Phone Configuration] in the navigation panel and open the [Phone Configuration]
Screen.
Figure 13-1 Phone Configuration
The following table describes this screen.
LABEL
Table 13-1 Phone Configuration
DESCRIPTION
Ring Cadence
Setting the played tone type, when VoIP Gateway is receiving a call.
Ring Back Tone
Setting the played tone type, when VoIP Gateway receives a Q.931
Alerting message. In condition that VoIP Gateway is the originate side.
Busy Tone
Setting the played tone type, when destination is busy.
Dial Tone
Setting the played tone type, when hook off a phone set of workable VoIP
Gateway.
- 55 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
2nd Dial Tone
To configure the value of the local 2nd dial tone (FXO only).
Flash Timer
Setting the detective flash range in ms, for example, 300-500 ms.
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
Note:
For tone simulation, VoIP Gateway adopts dual frequencies as traditional telephone does. If users
want to have their own call progress tone, they can change the value of tones. High and
Low frequency/level/cadence can be configured respectively.
¤
¤
¤
¤
¤
¤
ringing frequency: 15 ~ 100 (Unit: Hz)
ringing ring ON/OFF: 0 ~ 8000 (Unit: ms)
ringing level: 0 ~ 94 (Unit: V)
tone frequency: 0 ~ 65535 (Unit: Hz)
tone freqLevel: 0 ~ 65535 (Unit: mVrms)
tone Tone ON/OFF: 0 ~ 8000 (Unit: ms)
- 56 -
FXS H.323 VoIP Gateway User Manual
Chapter 14
RTP Payload Type Configuration Screen
This Chapter covers RTP Payload Type information and configuration
14.1 RTP Payload Type Configuration Overview
The web configurator provides Speed Dialing screen.
14.2 RTP Payload Type Configuration Screen
Click [RTP Payload Type Configuration] in the navigation panel and open the [RTP Payload
Type Configuration] Screen.
Figure 14-1 RTP Payload Type Configuration
The following table describes this screen.
LABEL
RFC2833 Payload
Type
Table 14-1 RTP Payload Type Configuration List
DESCRIPTION
Set the payload type for RFC2833 type.
DTMF Payload Type Set the payload for the DTMF type.
FAX Payload Type
Set the payload for the FAX type.
FAXByPass Payload Set the payload for the FAX by Pass type.
type
MODEMByPass
Payload Type
Set the payload for the Modem by Pass type. (This is no use for the
hardware as so far.)
- 57 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
Redundancy Payload Set the payload for the Redundancy type.
Type
MODEMRelay
Payload Type
Set the payload for the FAX by Pass type. (This is no use for the hardware
as so far.)
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
- 58 -
FXS H.323 VoIP Gateway User Manual
Chapter 15
IP Packet ToS Configuration Screen
This Chapter covers IP Packet ToS configuration.
15.1 IP Packet ToS Overview
The web configuration provides TOS Configuration screen.
15.2 IP Packet ToS Configuration Screen
Click [IP Packet ToS] in the navigation panel and open the [IP Packet ToS Configuration]
Screen.
Figure 15-1 IP Packet ToS Configuration
The following table describes this screen.
LABEL
Signaling Packet
DSCP Code
Table 15-1 IP Packet ToS Configuration
DESCRIPTION
Set the Signaling Packet DSCP code value, the value of is from 0 to 63
e.g.0.
Media Packet DSCP Set the Media Packet DSCP Code, the value of is from 0 to 63 e.g.0.
Code
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
- 59 -
FXS H.323 VoIP Gateway User Manual
Note:
It’s working if it supported by your network.
According to the RFC 1349 document, the TOS value as following:
1000 – minimize delay
0100 – maximize throughput
0010 – maximize reliability
0001 – minimize monetary cost
0000 – normal service
These values are the Binary format. Please change to the Decimal and put these values in to
the correct table.
- 60 -
FXS H.323 VoIP Gateway User Manual
Chapter 16
DDNS Device Configuration Screen
This Chapter covers Display DDNS related information.
16.1 DDNS Device Configuration Overview
The web configuration provides DDNS Device Configuration screen.
16.2 DDNS Device Configuration Screen
Click [DDNS Configuration] in the navigation panel and open the [DDNS Device
Configuration] Screen.
Figure 16-1 DDNS Device Configuration
The following table describes this screen.
LABEL
Table 16-1 DDNS Device Configuration
DESCRIPTION
Status
Select enable or disable to use DDNS device function.
Server
Enter the server address of your DDNS server.
Host Name
Your Dynamic DNS name.
ID
Your Dynamic DNS Login account.
Password
Your Dynamic DNS Login password.
Check IP
Select On or Off to check IP function. If use IP Sharing machine will use
check IP function. Then will get this information from your DDNS server.
IP Check Server 1
Set check the endpoints IP address.
- 61 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
IP Check Server 2
Set check the endpoints IP address.
Check Every
Set on/off function will check the server after a period. Set how long will
check it (0~59) minutes or (1~24) hours check it.
OK [button]
Click [OK] button to save your changes back to the VoIP Gateway volatile
memory.
Note:
Support DDNS Server: www.dyndns.org.
- 62 -
FXS H.323 VoIP Gateway User Manual
Chapter 17
Prefix Drop/Insert Configuration Screen
This Chapter covers to set Hotline function must be under Peer-to-Peer mode and switch to
hotline mode.
17.1 Prefix Drop/Insert Configuration Overview
The web configurator provides Bureau screen.
17.2 Prefix Drop/Insert Configuration Screen
Click [Prefix configuration] in the navigation panel and open the [Prefix Drop/Insert
Configuration] Screen.
Figure 17-1 Prefix Drop/Insert Configuration
The following table describes this screen.
LABEL
Table 17-1 Prefix Drop/Insert Configuration
DESCRIPTION
Index
This field refers to the index number.
Prefix
This field refers to the numbers that could be into VoIP gateway.
Drop
This field refers to the enable/disable drop function.
Insert
This field refers to the want to insert in this number.
New Prefix
Index
Setting the index number for prefix record (max 100 record).
Prefix
Setting the prefix number of the whole numbers that could be into this
- 63 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
VoIP gateway (1~20 digits).
Drop
Select enable or disable drop prefix function. The function is enable means
to drop prefix number when dialing out. The function is disable means to
keep prefix number.
Insert
Setting the digits that you want to insert in this number (1~30 digits).
Add Data [button]
Click [Add Data] button to insert the information table.
Delete Date [button]
Input the index number on index filed, and then click [Delete Data] button
will to delete the record from the table.
Note:
This function is just like the Phone Book configuration. But it will make the drop and insert
function in the GK routed mode. All the numbers into this gateway will check out the prefix table
first.
- 64 -
FXS H.323 VoIP Gateway User Manual
Chapter 18
Password Configuration Screen
This Chapter explains how to change the VoIP Gateway password.
18.1 Password Configuration Overview
The Password screen allows you to configure the administrator password.
18.2 Password Configuration Screen
Click [Password configuration] in the navigation panel to open the [Password Configuration]
screen.
Use the [Password Configuration] to set root and administrator password for the VoIP
Gateway.
It is highly recommended that you change the default password ([Null)).
Figure 18-1 Password Configuration
The following table describes this screen.
LABEL
Table 18-1 Password Configuration
DESCRIPTION
Username
Select root or administrator different options from the drop-down list box.
Current Password
Type the existing system password ([Null] is the default password when
shipped).
New Password
Type your new system password.
- 65 -
FXS H.323 VoIP Gateway User Manual
LABEL
DESCRIPTION
Confirm New
Password
Confirm your new system password for confirmation.
CHANGE [button]
Click [CHANGE] to save your change back to the VoIP Gateway volatile
memory.
ABORT [button]
Click [ABORT] to clean type data this page afresh.
- 66 -
FXS H.323 VoIP Gateway User Manual
Chapter 19
Version and Information Screen
This chapter explains the Version and Information Screen.
19.1 Version and Information Overview
The web configuration provides Version and Information screen to allow you to see VoIP
Gateway Version Information.
19.2 Version and Information Screen
Click [Version and Information] in the navigation panel to open the [Version and Information]
screen.
Figure 19-1 Version and Information
The following table describes this screen.
LABEL
Table 19-1 Version and Information
DESCRIPTION
Boot Rom
This field refers to the Boot Rom Version.
Application Rom
This field refers to the Application Rom Version.
DSP Application
This field refers to the DSP Application Version.
DSP Kernel
This field refers to the DSP Kernel Version.
DSP Test Code
This field refers to the DSP Test Code Version.
Greeting
This field refers to the Greeting file. (FXO only)
ASK Pin
This field refers to the ASK Pin file. (FXO only)
- 67 -
FXS H.323 VoIP Gateway User Manual
Chapter 20
ROM Upgrade Screen
This Chapter explains how to Update VoIP Gateway Version.
20.1 ROM Configuration Overview
The web configuration provides Update VoIP Gateway ROM Version.
20.2 ROM Configuration Screen
Click [ROM Upgrade] in the navigation panel and open the [ROM Configuration] Screen.
Figure 20-1 ROM Configuration
The following table describes this screen.
LABEL
Table 20-1 ROM Configuration
DESCRIPTION
Server IP Address
Enter the FTP or TFTP Server IP Address.
Target File Name
Enter the file name prepared to upgrade.
Method
Select download method as FTP or TFTP.
FTP Login Name
Enter the FTP Login name (max 20 byte)
FTP Login Password Enter the FTP Login password (max 20 byte)
Target File Type
Select download Target File Type on 2M Boot Image, DSP Application
Image, DSP Core Image, DSP Test Image different options from the
drop-down list box.
OK [button]
Click [OK] to save your change back to the VoIP Gateway volatile memory.
- 68 -
FXS H.323 VoIP Gateway User Manual
Note:
Most of all, the Rom file needed to get upgrade is App or Boot2m. Please check the exactly
Rom file before doing download procedure.
- 69 -
FXS H.323 VoIP Gateway User Manual
Chapter 21
Flash Clean Screen
This Chapter covers save change and clean the entire user defined value in factory default mode.
21.1 Flash Clean Overview
The web configuration provides Flash Clean screen.
21.2 Flash Clean Screen
Click [Flash Clean] in the navigation panel and open the [Flash Clean] Screen.
Figure 21-1 Flash Clean
The following table describes this screen.
LABEL
Clean [button]
Table 21-1 Flash Clean
DESCRIPTION
Clean all configuring VoIP Gateway stored.
Note:
User whose login name is root only executes it. All configurations in [Network Interface]
will be kept.
- 70 -
FXS H.323 VoIP Gateway User Manual
Chapter 22
Commit Data Screen
This Chapter covers save change after configuring VoIP Gateway.
22.1 Commit Configuration Data Overview
The web configuration provides Commit Configuration Data screen.
22.2 Commit Configuration Data Screen
Click [Commit Data] in the navigation panel and open the [Commit Configuration Data]
Screen.
Figure 22-1 Commit Configuration Data
The following table describes this screen.
LABEL
Commit [button]
Table 22-1 Commit Configuration Data
DESCRIPTION
Save changes after configuring VoIP Gateway.
- 71 -
FXS H.323 VoIP Gateway User Manual
Chapter 23
Reboot System Screen
This Chapter covers reboot to reload VoIP Gateway in new configuration.
23.1 Reboot VoIP Gateway Overview
The web configuration provides Reboot VoIP Gateway screen.
23.2 Reboot VoIP Gateway Screen
Click [Reboot System] in the navigation panel and open the [Reboot VoIP Gateway] Screen.
Figure 23-1 Reboot VoIP Gateway
The following table describes this screen.
LABEL
Reboot [button]
Table 23-1 Reboot VoIP Gateway
DESCRIPTION
After commit command, type reboot to reload VoIP Gateway in new
configuration. The procedure is as below:
- 72 -
FXS H.323 VoIP Gateway User Manual
Part III:
Command with VoIP Gateway
This part gives information on commands to use.
- 73 -
FXS H.323 VoIP Gateway User Manual
Chapter 24
Command List
This section introduces the command line interface and lists all of the commands.
24.1 Hyper Terminal Setting
A terminal emulator is needed when using RS-232 port to configure Gateway. There are
kinds of terminal emulator software. Here, we use Microsoft HyperTerminal to depict how to set
up terminal emulator:
Step 1.
Execute the Hyper Terminal program, and then the following windows will pop-up on
the screen (START¬Program files¬Accessories¬ Communication ¬Hyper
Terminal).
Step 2.
Figure 24-1 Connection Description
Define a name such as [3502] for this new connection, after pressing [OK] button.
Step 3.
Figure 24-2 Connection Description
The next windows appear, and then choose COM1/2 Port, which you are going to use.
- 74 -
FXS H.323 VoIP Gateway User Manual
Figure 24-3 Connect To
Step 4. Configure the COM Port Properties as following: Bits per second: 9600, Flow control:
None, Press [OK] button, and then start to configure Gateway.
Figure 24-4 Com Properties
24.2 Power Up Your Gateway
At this point, you should have connected the console port, the LAN Port, the WAN port and
the power port to the appropriate devices or lines. Plug the power adapter into a wall outlet. The
Power LED should be on. The [Status LED] will come on after the system tests are complete.
The WAN LED and one of the LAN LED come on immediately after the [Status LED] come on,
if connections have been made to the LAN and WAN ports.
¤ Initial Screen
When you power on your Gateway it performs server internal tests as well as line
initialization.
After the tests, the Gateway asks you to enter the Login, as shown.
....Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
Hardware Type : 4FXS
- 75 -
FXS H.323 VoIP Gateway User Manual
HTTPD initialized...
AC4804[0] is ok
AC4804[1] is ok
successful 2 2
Initialize OSS libraries...OK!
VP v1.44 stack open sucessfully.
cmInitialize succeed!
Ras port:1024
CallSignal port:1720
login:
Figure 24-5 Initial Screen
¤ Entering Login
For you first login, enter the login [root] and default password [Null]. As you type the
password, the screen displays and (*) for each character you type.
....Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
Hardware Type : 4FXS
HTTPD initialized...
AC4804[0] is ok
AC4804[1] is ok
successful 2 2
Initialize OSS libraries...OK!
VP v1.44 stack open sucessfully.
cmInitialize succeed!
Ras port:1024
CallSignal port:1720
login: root
Welcome to Terminal Configuration Mode
Please enter your configuration item
usr/config$
Figure 24-6 Login Screen
- 76 -
FXS H.323 VoIP Gateway User Manual
Note:
Login account [root] or [administrator] is the default login account and there is no password
needed.
¤ Set Password
To set your own password in root login name, just input command [passwd –set root ****].
For example, if password of root account is prepared as [voip], configuration it. When set
password ok, you can see ok message.
usr/config$ passwd -set root voip
Setting
Login: root
Password: voip
OK
usr/config$
Figure 24-7 password –set command
24.3 Command Structure with Gateway
24.3.1
Setup IP Address
Use command [ifaddr] to configure Gateway IP Address and related information.
For example:
Step 1.
Setting ip address
usr/config$ ifaddr –ip 192.168.1.11 –mask 255.2555.255.0 –gate 192.168.1.254
Description:
This is to configure Gateway IP Address as [192.168.1.11], subnet mask as [255.255.255.0],
default router gateway as [192.168.1.254].
Step 2.
Ather the configuration [commit] and [reboot] the device.
usr/config$ commit
usr/config$ reboot
Note:
After configured the IP Address and input the [commit], then [reboot] process, user can start
to do other configurations via HTTPD.
Application Version 200 supports PPPoE function for user to set up the login ID and
password to connect to Internet. Please refer to PPPoE mode for how to set up PPPoE.
- 77 -
FXS H.323 VoIP Gateway User Manual
24.3.2
Application Mode Configuration
It is including Basic mode, such as Gatekeeper and Peer-to-Peer, and Advanced mode, such
as Hotline mode and IP-Sharing mode. It will be detailed in the next Chapter.
24.3.3
Saving Your Configuration
Save the change of configurations for Gateway and apply the new configurations by
rebooting the device.
Step 1. Confirm the changed configurations, input [commit] and press [enter] key to save it.
Step 2. Input [reboot] then press [enter] key to restart Gateway.
Step 3. After around 40 seconds, Gateway will take effect in new configurations.
These commands save all system configuration into nonvolatile memory. Nonvolatile
memory refers to the Gateway storage that remains even if the Gateway power is turned of. Run
Time (memory) is lost when the Gateway power is turned off. You must use the command to
save any configuration that you make, otherwise the Gateway will return to its default setting
when it is restarted.
Do not turn off your Gateway or remove the Gateway
while saving your configuration.
24.4 Application modes
This Chapter will introduce the four application modes users often use. Particularly the
Gatekeeper and Peer-to-Peer mode are the basic application mode. User would like to set as
advanced application mode, such as Hotline Mode and Behind IP-Sharing mode, please refer to
the basic application mode for more information.
24.4.1
Gatekeeper mode
User has to prepare a Gatekeeper Program. To assign a gatekeeper address for Gateway, and
define it’s own registered ID and phone number. For detail, please refer to [h323] command.
Several important H323 parameters are listed below when setting gatekeeper mode: [–gk],
[gwtype], [-prefix], [–line1], [–line2], [–line3], and [–line4].
Step 1.
Setting gatekeeper mode, and line number
usr/config$ h323 –mode 0 (default gatekeeper mode)
usr/config$ h323 –gk 192.168.1.1 –prefix 1 –line1 11 –line2 12 –line3 13 –line4 14
For example:
usr/config$ h323 -print
H.323 stack relate information
RAS mode
: GK mode
Gatekeeper IP address
: 192.168.13.71
Second Gatekeeper IP
: 192.168.13.71
- 78 -
FXS H.323 VoIP Gateway User Manual
Gateway Type
: Gateway
Registered prefix number : 1
Line1
: 11
Line2
: 12
Line3
: 13
Line4
: 14
H.235 security token
:*
Registered alias
: 4FXS-0015db
Display Information
: 4FXS
Gatekeeper discovery
: Off
Gatekeeper ID
: GK
RAS TTL time
: 60
RTP port
: 16384
Gatekeeper finding port : 1718
GK RAS port
: 1719
H225 RAS port
: 1024
H225 Call signal port
: 1720
Allocated port range
:
start port
: 1024
end port
: 1043
Response timeOut
: 15
Connect timeOut
: 200
usr/config$
Note:
This is to set gatekeeper IP address as [192.168.1.1], prefix as [1], line 1 number as [11],
line 2 number as [12], line 3 number as [13], and line 4 number as [14]. The gateway type is
kept as default value as Gateway Type.
Step 2.
Ather the configuration [commit] and [reboot] the device.
usr/config$ commit
usr/config$ reboot
24.4.2
Peer-to-Peer Mode
Peer-to-Peer Mode allows users to call other VoIP devices without using a gatekeeper. When
in Peer-To-Peer mode, Gateway will send SETUP message directly to the destination IP address
once the dial is finished. Users have 2 methods of dial. One is IP Address dialing, and the other is
[Phone Book] dial, which we will describe later. When using IP address as destination phone
- 79 -
FXS H.323 VoIP Gateway User Manual
number, press [*] as [.] in IP address expression, and press [#] when dial is finished.
When using Phone Book, users can dial predefined phone number, and press [#] as end of
dial.
To configure Peer-To-Peer Mode in Gateway, follow the steps below:
Step 1.
Set Peer-To-Peer Mode, using [h323] command
usr/config$ h323 –mode 1 (Peer To Peer mode)
For example:
usr/config$ h323 –print
H.323 stack relate information
RAS mode
Default Gateway
Line1(TEL 1)
Line2(LINE 1)
Line3(TEL 2)
Line4(LINE 2)
Alias(H323-ID)
Display Information
RTP port
: Peer-to-Peer
:x
: 1001
: 1002
: 1003
: 1004
: 4FXS-0015db
: 4FXS
: 16384
H225 Call signal port
: 1720
Destination H225 call signal port : 1720
Allocated port range
:
start port
: 1024
end port
: 1043
Response timeOut
: 15
Connect timeOut
: 200
usr/config$
Step 2.
Configure Phone Book, using [pbook] command.
Users can refer to [pbook] command for more information.
usr/config$ pbook –add name TEST1 ip 192.168.1.20 e164 20
Memo:
The command is to add a record onto PhoneBook. After the command completed, you
can type [pbook –print] to see if the input record is correct.
Step 3.
Ather the configuration [commit] and [reboot] the device.
usr/config$ commit
usr/config$ reboot
- 80 -
FXS H.323 VoIP Gateway User Manual
24.4.3 Hotline Mode
The Hotline Mode is applied in limited two peers. User just picks up the phone set and then
hears ring back tone or dial tone depended on configurations of destination device.
¤ Gatekeeper Mode
Step 1.
Step 2.
Set gateway under Gatekeeper mode.
Create a Hotline table with [line] command.
Usr/config$ line –config 1 hotline 1001
In this example means: if user picks up phone set of FXS Line1, gateway will automatically
dial out [1001].
Step 3.
Ather the configuration [commit] and [reboot] the device.
Usr/config$ commit
usr/config$ reboot
¤ P2P Mode Usage:
Step 1.
Step 2.
Step 3.
Set gateway under P2P mode.
Create phone book table with [pbook] command.
Create a Hotline table with [line] command.
usr/config$ h323 –mode 1
usr/config$ pbook –add name test ip 10.1.1.1 e164 1001
usr/config$ line –config 1 hotline 1001
In this example means: if user picks up phone set of FXS Line1, gateway will automatically
dial out IP address of [1001].
Step 4.
Ather the configuration [commit] and [reboot] the device.
usr/config$ commit
usr/config$ reboot
24.4.4 Forward Mode
Set no answer forward table provides No Answer Forward function. For call forward
function, it can works under GK or P2P mode.
¤ GK Mode Usage:
Step 1.
Setting Line1 busy forward Line2
usr/config$ line –config 1 forward 1002
In this example means: if user calls in FXS Line and hasn’t been answered in forward time
(please refer to [sysconf -forwardtime] command), gateway will automatically forward this call
to phone number [1002].
Step 2.
Ather the configuration [commit] and [reboot] the device.
- 81 -
FXS H.323 VoIP Gateway User Manual
usr/config$ commit
usr/config$ reboot
¤ P2P Mode Usage:
Step 1.
Setting Line1 busy forward Line2
usr/config$ line –config 1 forward 1002
In this example means: if user calls in FXS Line1 when Line1 is busy, gateway will
automatically forward this call to IP address of [1002] in Phone book.
Step 2.
Ather the configuration [commit] and [reboot] the device.
usr/config$ commit
usr/config$ reboot
24.4.5
Behind IP-Sharing Mode
The function is for user whose network environment is behind IP Sharing device. It is said
Gateway is connected to the IP Sharing device.
An example such as ADSL network is in the following.
Step 1.
The WAN IP Address obtained from ADSL has two kinds of methods. One is fixed IP
Address, while user applies for one or more fixed IP Addresses. Another is dynamic IP
Address while user applies for dial-up connection way.
Step 2.
The LAN IP Address of User’s PC can be set as DHCP client in order to gain a valid
one.
Step 3. Another IP Address for Gateway must be set as an fixed one in order for that
IP Sharing device pass forwarding the relevant information from WAN to LAN. Besides, a
valid IP Address meets the IP Sharing device (LAN site) is the element.
- 82 -
FXS H.323 VoIP Gateway User Manual
Step 4.
Gateway must enable the IP Sharing function for the fixed/dynamic WAN IP Address.
Fixed IP Address:
usr/config$ ifaddr –ipsharing 1 210.11.22.33
Dynamic IP Address:
usr/config$ ifaddr –ipsharing 1
Note:
With Dynamic WAN IP Address, a valid Gatekeeper for Gateway to get register on is a
must. In other word, it is not workable in Peer-to-Peer mode while dynamic WAN IP
Address.
Step 5.
Ather the configuration [commit] and [reboot] the device.
usr/config$ commit
usr/config$ reboot
Step 6. IP Sharing device must have a function to do IP/Port mapping. Some is named as DMZ,
some is named as virtual server whatever. The VoIP messages from WAN have to
completely pass forward to the LAN. It is said if the Gateway is assigned a virtual fixed IP
Address such as 192.168.1.5, IP Sharing device must forward the VoIP message to
192.168.1.5.
Important Notes:
For some IP-Sharing devices do not support DMZ or virtual server function, but allowed user
to allocate some particular TCP/UDP port range.
While a complete H.323 communication is established, the following ports are possibly to be
used:
TCP port:
Q.931/H.225
H.245
1720
Dynamic,
But range 1025 ~ 1029 (not in use if Fast Start or Tunnel mode is
activated)
UDP port:
RAS
Device: 1024,
Gatekeeper: 1719
RTP/RTCP
Adjustable,
Default: 16384 ~ (16384 + 4*Line Numbers)
- 83 -
FXS H.323 VoIP Gateway User Manual
Note:
The port number allocation is for reference only. RTP/RTCP port may allocate on unexpected
port. It is better to define the port in wider range than limited range
24.4.6
PPPoE Mode
Step 1.
Set PPPoE mode, using [ifaddr]
usr/config$ ifaddr –mode 2 (PPPoE mode)
Step 2.
Input the user id & password provided by your ISP, using [ifaddr]
usr/config$ ifaddr –id 123@hinet.net (PPPoE login account)
usr/config$ ifaddr –pwd 123 (PPPoE login Passowd)
Step 3.
Reboot the device once after disconnection, using [ifaddr]
usr/config$ ifaddr –reboot 1 (Enable)
For example:
usr/config$ print
IP mode : PPPoE
PPPoE adapter information
Status
: Not initialized
DNS primary
: 168.95.1.1
DNS secondary
: 168.95.1.2
HTTP port
: 80
SNTP
: mode=1
server 168.95.195.12
time zone : GMT+8
cycle=1024 mins
IPSharing
: no IPSharing device.
IP change
: Disable
PPPoE user name
PPPoE password
: 84460791@hinet.net
: ********
- 84 -
FXS H.323 VoIP Gateway User Manual
PPPoE reboot
: Yes
usr/config$
Step 4.
Ather the configuration [commit] and [reboot] the device.
usr/config$ commit
usr/config$ reboot
Step 5.
When Gateway connection success.
For example:
usr/config$ ifaddr -print
IP mode : PPPoE
PPPoE adapter information
Status
: Ready
IP address
Destination
DNS primary
Subnet Mask
Authenticate
: 61.216.36.6
: 61.216.36.254
: 168.95.192.1
: 255.255.255.255
: PAP Protocol
: TCP/IP
Device
DNS primary
DNS secondary
HTTP port
SNTP
: PPP/PPPoE
: 168.95.1.1
: 168.95.1.2
: 80
: mode=1
server 168.95.195.12
time zone : GMT+8
cycle=1024 mins
IPSharing
: no IPSharing device.
IP change
: Disable
PPPoE user name
PPPoE password
PPPoE reboot
: 84460791@hinet.net
: ********
: Yes
usr/config$
- 85 -
FXS H.323 VoIP Gateway User Manual
24.4.7
PPPoE (NAT) mode (Dynamix DW- 1 FXS only)
Step 1.
Set PPPoE mode, using [ifaddr]
usr/config$ ifaddr –mode 2 (PPPoE mode)
Step 2.
Input the user id & password provided by your ISP, using [ifaddr]
usr/config$ ifaddr –id 123@hinet.net (PPPoE login account)
usr/config$ ifaddr –pwd 123 (PPPoE login Passowd)
Step 3.
Reboot the device once after disconnection, using [ifaddr]
usr/config$ ifaddr –reboot 1 (Enable)
For example:
usr/config$ print
IP mode : PPPoE
PPPoE adapter information
Status
: Not initialized
DNS primary
: 168.95.1.1
DNS secondary
: 168.95.1.2
LAN port IP (for NAT): 192.168.123.123
HTTP port
: 80
SNTP
: mode=1
server 168.95.195.12
time zone : GMT+8
cycle=1024 mins
IPSharing
: no IPSharing device.
IP change
: Disable
- 86 -
FXS H.323 VoIP Gateway User Manual
PPPoE user name
PPPoE password
PPPoE reboot
: 84460791@hinet.net
: ********
: Yes
usr/config$
Step 4.
Ather the configuration [commit] and [reboot] the device.
usr/config$ commit
usr/config$ reboot
Step 5.
When Gateway connection success.
Step 6.
Setup PC use LAN IP connection Network
Select [Specify an IP Address] and enter [192.168.123.111] in the [IP Address] location
(where xxx is a number between 2 and 254 used by the VoIP Gateway to identify each
computer), and the default [Subnet Mask 255.255.255.0]. Note than no two computers on
the same LAN can have the same IP address. Gateway default gateway value
192.168.123.123 in the [new gateway] field. Then save your change.
Note:
One Group only use only LAN IP address, if have two gateway on this group, you must
change second gateway LAN IP Address different first gateway.
Gateway First:
usr/config$ ifaddr -lanip 192.168.124.124
Gateway Second:
usr/config$ ifaddr -lanip 192.168.124.125
Important Note:
This command function only Dynamix DW- FXS 01 (FXS-01) VoIP Gateway used. So, other
mode VoIP Gateway not sees it.
For example:
usr/config$ ifaddr -print
IP mode : PPPoE
PPPoE adapter information
Status
: Ready
IP address
: 61.216.36.6
Destination
: 61.216.36.254
LAN port IP (for NAT): 192.168.123.123
DNS primary
: 168.95.192.1
Subnet Mask
: 255.255.255.255
Authenticate
: PAP
- 87 -
FXS H.323 VoIP Gateway User Manual
Protocol
Device
: TCP/IP
: PPP/PPPoE
DNS primary
: 168.95.1.1
DNS secondary
HTTP port
SNTP
: 168.95.1.2
: 80
: mode=1
server 168.95.195.12
time zone : GMT+8
cycle=1024 mins
IPSharing
: no IPSharing device.
IP change
: Disable
PPPoE user name
PPPoE password
PPPoE reboot
: 84460791@hinet.net
: ********
: Yes
usr/config$
24.4.8
H.450 Call Hold, Transfer and Forward Mode
Gateway provides H.450 function including call hold, transfer and forward. Please be noted
that both calling and called site have to support H.450 feature. For call forward function, it only
works under GK mode. Of course, GK must support H.450 feature.
To enable H.450 feature, it is better for user to prepare a telephone set supported [FLASH]
function on keypad. If telephone set does not support [FLASH] function on keypad, user is
possible to click the Hook quickly by sending FLASH message. The default FLASH value for
Gateway is between 100ms to 300 ms. It is said the value of Gateway is subject to the telephone
set.
¤ Call Hold – press [FLASH]
By pressing the FLASH after making a call, both site shall hear the 2nd dial tone generated
by Gateway. To retrieve the call back, just press the FLASH again.
¤ Call Transfer – press [FLASH], then [transferring number]
For example, A call B, B transfer to C
A make call to B, B press FLASH. A and B hear 2nd dial tone. B presses the C’s number. C
ringing and A hear the RingBack tone. B Hang up its call. A and C Make call.
¤ Call Forward:
¤ Activate - *147#
¤ Deactivate - *258#
¤ Busy Forward – [Forward No.] *#
- 88 -
FXS H.323 VoIP Gateway User Manual
¤ No response/ Answer – [Forward No.]*1#
¤ Unconditional – [Forward No.]*2#
It is important to send an activate/deactivate call forward message before setting up the
forward number. This function is only available under GK mode, and the GK supports H.450
Call Forward function. There are three conditions for user to set a forwarding number.
Step 1.
Step 2.
Step 3.
Busy Forward – while line is engaged or phone set is off-hook.
No response/Answer – while no one answer the call.
Unconditional – forward it unconditionally.
24.5 How to upgrade
¤ Before you start downloading
Step 1.
Please confirm Host PC, which is installed as TFTP / FTP server and device is in
available network.
Step 2. Remember the current configuration, such as [h323], [line], [pbook], and you change
configuration data.
Step 3.
It will list current version and default download method. Please check the Application
Rom in particular, it is showed version list, as well as the most common one you have to
upgrade.
Step 4.
General speaking, App Rom is named including product name and version and size is
under 1MB, such as 2fxs.115a. 2MB Rom is named such as 2m2fxs.115a. Please be very
careful of the prepared Rom file while upgrading.
Step 5.
Check Application Rom Version, input [rom –print] command
For example:
usr/config$ rom –print
Download Method : TFTP
Boot Rom
Application Rom
DSP App
DSP Kernel
DSP Test Code
:
:
:
:
:
sdboot.200
4afxs.203a
48302ce3.140
48302ck.140
483cbit.bin
usr/config$
Step 6.
Prepare FTP or TFTP server ready.
¤ Upgrade steps: FTP Mode (Application Rom)
- 89 -
FXS H.323 VoIP Gateway User Manual
Step 1. Choose Download Method: FTP method
1. [-method]: Choose download method: FTP method,
2. input the FTP Login name and password
3. [rom -print]: check configuration data
usr/config$ rom –method 1
usr/config$ rom –ftp id password
usr/config$ rom –print
For example:
usr/config$ rom -print
Download Method : FTP
FTP username : test
FTP password : test
Boot Rom : sdboot.200
Application Rom
DSP App
DSP Kernel
DSP Test Code
:
:
:
:
4afxs.203a.bin
48302ce3.140
48302ck.140
483cbit.bin
usr/config$
Step 2. Application Rom upgrade
1. [-app]: Choose means the prepared upgrade Rom.
2. [-s]: input the FTP Server IP Address.
3. [-f]: input the Rom files name
usr/config$ rom –app –s 192.168.1.1 –f 4afxs.204
Step 3. flash –clean
Command [flash -clean] to clear old configurations. It will keep all configurations in
[ifaddr].
usr/config$ flash –clean
Note:
Old version: such as 115a, will only keep IP Address and MAC Address.
¤ Upgrade steps: TFTP Mode (Boot2m)
Step 1. Choose Downlaod Method: TFTP method (default)
1. [-method]: Choose download method: TFTP method,
- 90 -
FXS H.323 VoIP Gateway User Manual
2. [rom -print]: check configuration data
usr/config$ rom –method 0
usr/config$ rom –print
For example:
usr/config$ rom –print
Download Method : TFTP
Boot Rom
Application Rom
DSP App
DSP Kernel
DSP Test Code
:
:
:
:
:
sdboot.200
4afxs.203a
48302ce3.140
48302ck.140
483cbit.bin
usr/config$
Step 2. Boot2m upgrade
1. [-boot2m]: Choose means the prepared upgrade Rom.
2. [-s]: input the FTP Server IP Address.
3. [f]: input the Rom files name
usr/config$ rom –boot2m –s 192.168.1.1 –f 2m4afxsH.204
Note:
If the version list is older than 113, all configurations will be back to default value,
including IP Address. In other word, user has to set IP Address and MAC Address before
[reboot] the device; otherwise, user cannot access to device any more via Telnet.
The version 200 and above support to keep every configurations after upgrade. If you
upgrade version 200 over and above you check step 6.
Step 3. Find out MAC Address:
There are 12 digits on label on the back panel of the device, or command as [ifaddr -ifshow]
(find the list information of Ethernet address, it is MAC Address).
usr/config$ ifaddr –ifshow
For example:
usr/config$ ifaddr -ifshow
cpm (unit number 0):
Flags: (0x8063) UP BROADCAST MULTICAST ARP RUNNING
Type: ETHERNET_CSMACD
Internet address: 192.168.13.80
Broadcast address: 192.168.15.255
- 91 -
FXS H.323 VoIP Gateway User Manual
Netmask 0xfffff800 Subnetmask 0xfffff800
Ethernet address is 00:01:a8:00:27:43
Metric is 0
Maximum Transfer Unit size is 1500
0 octets received
0 octets sent
221 packets received
0 packets sent
221 unicast packets received
0 unicast packets sent
0 non-unicast packets received
0 non-unicast packets sent
0 input discards
0 input unknown protocols
0 input errors
138 output errors
0 collisions; 0 dropped
Step 4.
Set MAC Address:
usr/config$ setmac
- enter mac address (xxxxxxxxxxxx):
For example:
usr/config$ setmac
- enter mac address (xxxxxxxxxxxx):0001a8002743
- the mac address is 00 01 a8 00 27 43
- if mac address is correct,please press 'y' to
setup configuration,else press 'n' to continue
y
- mac address configuraton OK.
usr/config$
Step 5.
Set IP Address:
usr/config$ ifaddr –ip xxx.xxx.xxx.xxx –mask xxx.xxx.xxx.xxx –gate xxx.xxx.xxx.xxx
Step 6.
commit, reboot
usr/config$ commit
usr/config$ reboot
24.6 Commands with Gateway
The following table lists all of the commands that you can use with the Gateway. Refer to the
- 92 -
FXS H.323 VoIP Gateway User Manual
following chapters for descriptions of commonly used commands.
This user’s guide describes commands that are helpful for configuring the Gateway. Using
commands not documented in the user’s guide can damage the unit and possibly render it
unusable.
Command
Table 24-1 Commands with Gateway
Description
help
help/man/? [command]
quit
quit/exit/close
debug
Show debug message
reboot
Reboot local machine
flash
Clean configuration from flash rom
commit
Commit flash rom data
ifaddr
Internet address manipulation
time
Show current time
ping
Test that a remote host is reachable
sysconf
System information manipulation
h323
H.323 information manipulation
line
Gateway line information and configuration
prefix
Prefix drop/insert information manipulation
pbook
Phonebook information and configuration
voice
Voice information manipulation
support
Special Voice function support manipulation
sysinfo
System information
phone
Setup of call progress tones and ringing (SLIC control)
tos
IP Packet ToS (Type of Service) values
ddns
Dynamic DNS update manipulation
pt
RTP payload type configuration and information
rom
ROM file update
passwd
Password setting information and configuration
24.7 System Commands Overview
24.7.1
[quit]
Type [quit] will quit the Gateway configuration mode. And turn back to login prompt.
usr/config$ quit
Disconnecting..
- 93 -
FXS H.323 VoIP Gateway User Manual
login: root
Welcome to Terminal Configuration Mode
Please enter your configuration item
usr/config$
Figure 24-8 quit commend
Note:
It is recommended that type the [quit] command before you leave the console. If so,
Gateway will ask password again when next user connects to console port.
24.7.2
[debug]
Open debug message will show up specific information while Gateway is in operation.
After executing the debug command, it should execute command [debug –open] as well.
usr/config$ debug
Debug message information and configuration
Usage:
debug [-add type1 [[type2]..]] | -open | -close | -status
-status
Display the enabled debug flags.
-add
Add debug flag.
-delete
Remove specified debug flag.
-open
Start to show debug messages.
-close
Stop showing debug messages.
Example:
debug -add h323 h323vp
debug -open
usr/config$
Figure 24-9 debug commend list
Parameter Usages:
-status: Display the enabled debug flags.
-add: Add debug flag.
-- h323: h323 related information
-- vp: voice related information
-delete: Remove specified debug flag.
-open: Start to show debug messages.
- 94 -
FXS H.323 VoIP Gateway User Manual
-close: Stop showing debug messages.
In this example, user open debug flags including h323, vp, h323vp.
usr/config$ debug -add h323 vp h323vp
usr/config$ debug –open
For example:
usr/config$ debug -status
Current debug type enabled :
Debug Mode is open
DEBUG-> H323VP H323
usr/config$
Figure 24-10 debug –status commend
24.7.3
[reboot]
After [commit] command, type [reboot] to reload Gateway in new configuration. The
procedure is as below:
usr/config$ reboot
....Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
Hardware Type : 4FXS
HTTPD initialized...
AC4804[0] is ok
AC4804[1] is ok
successful 2 2
Initialize OSS libraries...OK!
VP v1.44 stack open sucessfully.
cmInitialize succeed!
Ras port:1024
CallSignal port:1720
login:
Figure 24-11 reboot commend
- 95 -
FXS H.323 VoIP Gateway User Manual
24.7.4
[flash]
Clean the configuration stored in flash.
usr/config$ flash
Flash memory information and configuration
Usage:
flash [-clean]
flash -clean Clean the configuration stored.
Note:
This command will clean the configuration stored in
the flash and reboot it.
usr/config$
Figure 24-12 flash commend list
Parameter Usages:
-clean: clean all the user defined value, and reboot Gateway in factory default mode.
Note:
It is recommended that use [flash –clean] after application firmware id upgraded.
Warning:
User whose login name is root only executes it. All configurations in command [ifaddr] will
be kept.
For example:
usr/config$ flash -clean
Flash clean ok!! Rebooting ...
Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
Hardware Type : 4FXS
HTTPD initialized...
cmInitialize succeed!
Ras port:1024
CallSignal port:1720
- 96 -
FXS H.323 VoIP Gateway User Manual
AC4804[0] is ok
AC4804[1] is ok
successful 2 2
Initialize OSS libraries...OK!
VP v1.44 stack open sucessfully.
login:
Figure 24-13 flash –clean commend
24.7.5
[commit]
Save changes after configuring Gateway.
usr/config$ commit
This may take a few seconds, please wait..
Commit to flash memory ok!
usr/config$
Figure 24-14 commit commend
Note:
Users shall use [commit] to save modified value, or they will not be activated after system
reboot.
24.7.6
[ifaddr]
Configure and display Gateway network information.
LAN information and configuration
Usage:
ifaddr [-print][-mode used][-ip IP Address][-mask Subnet Mask]
[-gate Default Gateway][-dns 1 IP Address][-http portnumber]
[-lanip IP Address][-sntp mode [server]][-timezone GMT]
[-ipsharing used IP address][-ipchange used][-id PPPoE username]
[-pwd PPPoE password][-reboot used]
-print
-mode
-ip
-mask
Display network information and configuration.
Specify WAN IP mode (0=Static, 1=DHCP, 2=PPPoE).
Specify WAN port static IP address.
Set WAN port static IP subnet mask.
- 97 -
FXS H.323 VoIP Gateway User Manual
-gate
-dns
Specify WAN port static IP default gateway IP address
Set DNS server IP address. Provide set DNS primary and
secondary IP address (1=primary IP address, 2=secondary).
-http
Specify http port number.
-lanip
-sntp
Specify LAN port IP address (For NAT function).
Set SNTP server mode and specify IP address.
SNTP mode (0=No update, 1=Specify server IP, 2=broadcast mode).
-timezone Set local timezone.
-ipsharing Specify usage of an IP sharing device and specify IP address
(0=Disable, 1=Enable).
-ipchange Replace IP address if the shared IP is changed
(0=Disable, 1=Enable).
-id
PPPoE connection user name.
-pwd
PPPoE connection password.
-reboot
Reboot after remote host disconnection in PPPoE mode
(0=No Reboot, 1=Yes Reboot).
Note:
Range of IP address setting (0.0.0.0 ~ 255.255.255.255).
Example:
ifaddr -mode 0
ifaddr -ip 210.59.163.202 -mask 255.255.255.0 -gate 210.59.163.254
ifaddr -dns 1 168.92.1.1 -dns 2 168.95.1.2
ifaddr -http 80
ifaddr -lanip 192.168.123.123
ifaddr -sntp 1 210.59.163.254
ifaddr -ipsharing 1 210.59.163.254
ifaddr -ipchange 1
ifaddr -id 123456@hinet.net -pwd 123456 -reboot 1
Figure 24-15 ifaddr commend list
Parameter Usages:
-print: Print current IP setting and status
-mode: Specify WAN IP mode (0=Static, 1=DHCP, 2=PPPoE), DHCP mode: Dynamic Host
Configuration, PPPoE mode: PPPoE Dial-up function.
-ip: Assigned IP address for Gateway
-mask: Assigned internet subnet mask
-gate: Assigned IP default gateway
-dns: Setup DNS Server IP Address.
- 98 -
FXS H.323 VoIP Gateway User Manual
-http: Assiged Gateway web browser connection port number, default port number 80.
-lanip: Specify LAN port IP address (For NAT function), use this command setup lanip
address assigned to PC or other machine. Setting IP address provide PC setup
Default Gateway Address.
usr/config$ ifaddr -lanip 192.168.124.124
Note:
One Group only use only LAN IP address, if have two gateway on this group, you must
change second gateway LAN IP Address different first gateway.
Gateway First:
usr/config$ ifaddr -lanip 192.168.124.124
Gateway Second:
usr/config$ ifaddr -lanip 192.168.124.125
Important Note:
This command function only 1FXS (FXS-01) VoIP Gateway used. So, other mode VoIP
Gateway not sees it.
-sntp: Simple Network Time Protocol (0=No update, 1=Specify server IP, 2=broadcast mode).
When SNTP function is activated, users have to specify a SNTP server as network time
source. An example is demonstrated below:
usr/config$ ifaddr -sntp 1 10.1.1.1
Note:
While 10.1.1.1 stands for SNTP server’s IP address.
-timezone: set local time zone according to GMT
-ipsharing: To specify a global fixed IP address, user can add this IP address in the command.
usr/config$ ifaddr -ipsharing 1 210.11.22.33
Note:
If the IP address is not a fixed one, the dedicated IP address is not necessary in the
command. However, dynamic IP Address is not working in Peer-to-Peer mode.
-ipchange: If the unit is behind the IP sharing device and the IP address for the WAN port of that
IP sharing is using the dynamic IP address. This function has to be enabled.
usr/config$ ifaddr -ipchange 1
-id: This id is for the user name of the PPPoE usage.
-pwd: This password is for the user name of the PPPoE usage.
-reboot: If the connection disconnected by the ISP, the unit will reboot and get the ip again.
For example:
usr/config$ ifaddr –print
- 99 -
FXS H.323 VoIP Gateway User Manual
IP mode : Static
Internet address information
IP address
: 192.168.13.78
Subnet mask
: 255.255.248.0
Default gateway
: 192.168.8.254
LAN port IP (for NAT): 192.168.123.123
DNS primary
: 168.95.1.1
DNS secondary
: 168.95.1.2
HTTP port
: 80
SNTP
: mode=1
server 168.95.195.12
time zone : GMT+8
cycle=1024 mins
IPSharing
: no IPSharing device.
IP change
: Disable
PPPoE user name
:
PPPoE password
:
PPPoE reboot
usr/config$
: No
Figure 24-16 ifaddr –print command
24.7.7
[time]
When SNTP function of Gateway is enabled and SNTP server can be found as well, type
[time] command to show current network time.
usr/config$ time
Current time is WED SEP 17 12:36:49 2003
usr/config$
Figure 24-17 time commend list
24.7.8
[ping]
Use [ping] to test whether a specific IP is reachable or not.
For example: if 192.168.1.2 is not existing while 210.63.15.32 exists. Users will have the
following results:
usr/config$ ping 192.168.1.2
no answer from 192.168.1.2
- 100 -
FXS H.323 VoIP Gateway User Manual
usr/config$ ping192.168.1.254
PING 192.168.1.254: 56 data bytes
64 bytes from 192.168.1.254: icmp_seq=0. time=5. ms
64 bytes from 192.168.1.254: icmp_seq=1. time=0. ms
64 bytes from 192.168.1.254: icmp_seq=2. time=0. ms
64 bytes from 192.168.1.254: icmp_seq=3. time=0. ms
----192.168.1.254 PING Statistics---4 packets transmitted, 4 packets received, 0% packet loss
round-trIP (ms) min/avg/max = 0/1/5
210.63.15.32 is alive
usr/config$
Figure 24-18 ping commend list
24.7.9
[sysconf]
This command displays system information and configurations.
usr/config$ sysconf
System information and configuration
Usage:
sysconf [-print][-idtime digit][-forwardtime digit][-keypad used]
[-prefixsw used][-prefixdisab used][-usrdefprefix digits]
[-codec used][-localrbt used][-gwprefix used][-eod used]
-print
Display system overall information and configuration.
-idtime
Inter-Digits time (1~10 sec).
-forwardtime Forward time for FXS line if no answer (5~65535 sec).
-keypad
Select DTMF type: 0=In-band,
1=H.245 Alphanumeric,
2=H.245 SignalType,
3=Q.931 UserInfo.
4=RFC2833.
-prefixsw
User defined local zone prefix switch (0=OFF, 1=ON).
-prefixdisab Local zone prefix disable character (one character
from 0~9, *, or NONE('-' key)).
-usrdefprefix User defined local zone prefix (0 ~ 20 digits).
-codec
Codec select method (0=Caller, 1=Master).
-localrbt
Local ring back tone (0=Disable, 1=Enable).
-gwprefix
Drop gateway prefix when call from IP (0=Keep, 1=Drop).
- 101 -
FXS H.323 VoIP Gateway User Manual
-eod
End of dial (0=Disable, 1=Enable).
Example: sysconf -idtime 5
usr/config$
Figure 24-19 sysconf commend list
Parameter Usages:
-print: Print current sysconf settings.
-idtime: Set the duration (in second) of two pressed digits in dial mode as timed out. If after the
duration user hasn’t pressed next number, it will dial out all number pressed (1-10
seconds).
-forwardtime: Set forward time (5-65535 seconds) for FXS Line. If call hasn’t answered the call
in this time, call will be forward to assigned number in [line] command. (Please refer to
[line] command for forward setting.)
-keypad: Select DTMF replay type (0=In-band, 1=H.245 Alphanumeric, 2=H.245 SignalType,
3=Q.931 UserInfo, 4=RFC2833), Users can adjust the value according to various
applications. In-band: Gateway will transfer DTMF signal via RTP payload. H.245
Alphanumeric via H.245 UII Alphanumeric. H.245 SignalType FXS (VoIP) via H.245
UII Singal Type. Q.931 UserInfo via Q.931 UserInfo. RFC2833 via RFC2833.
-prefixsw: Switch on/off prefix function. If user enables prefix function, once user dials out,
gateway will automatically add prefix number before number user dialed.
-prefixdisab: Set disable key (0,1~9, *) to disable the prefix function in this current call. For
example, if user has set prefix as 100, and wants to dial out 100123, user can only press
123, to dial out 100123.However, if user wants to dial 123 without prefix, user can press
prefix disable key, for example [*], user can press [*], then dial 123, gateway will dial out
123 without adding prefix.
-usrdefprefix: Define prefix number.
Note:
The above three commands [prefixsw], [prefixdisab] and [usrdefprefix] have to work
together. If user would like to dial 9 to replace 123456789, he can firstly switch on the
command [sysconf -prefixsw 1], secondly to define the prefix digits as 12345678
[sysconf –usrdefprefix 12345678]. While user would like to dial other numbers, he can dial a
defined digit – [*] to disable the function [sysconf –prefixdisab *], then dial to the number he
wants to dial.
-codec: Set who is the one to determine voice codec during negotiation. 0 is caller will determine
the codec, and 1 is mater will determine the codec. (During negotiation 2 endpoints will
compare gateway type level to determine who is master.)
-localrbt: Enable or Disable locally generate ring back tone. Disable means gateway will receive
- 102 -
FXS H.323 VoIP Gateway User Manual
ring back tone from remote callee, Enable means gateway will generate ring back tone
locally.
-gwprefix: Drop or keep gateway prefix . Keep Means when gateway has incoming call from IP
side, it will not drop prefix before searching for call number. Drop Means when gateway
has incoming call from IP side, it will drop prefix before searching for called number.
-eod: It will transfer the DTMF in [#] if users disable the end of dial function. Users have to press
the keypad in [#] if the end of dial function is enable.
Note:
User can also define IP address here in P2P mode, once user press “#”, Gateway will
call out this IP address.
For example:
usr/config$ sysconf -print
System information
Inter-Digits time
Forward time
Keypad DTMF type
User defined prefix switch
:3
: 30
: In-band
: OFF
User defined prefix disable
:*
User defined prefix
Codec select method
:0
: Master
Local generate ring back tone : Enable
Gateway prefix
End of dial
usr/config$
: Keep
: Enable
Figure 24-20 sysconf -print commend
24.7.10
[h323]
This command is to configure H.323 related parameters.
usr/config$ h323
H.323 stack information and configuration
Usage:
h323 [-print][-mode used][-gk IP address][-algk IP address][-gwtype used]
[-dfgw IP address][-prefix number][-line number][-passwd number]
[-alias h323id][-display information][-gkid ID][-gkdis used]
- 103 -
FXS H.323 VoIP Gateway User Manual
-print
-mode
Display H.323 stack information and configuration.
Configure as Gatekeeper mode or Peer-to-Peer mode
(0=Gatekeeper, 1=Peer-to-Peer).
-gk
Gatekeeper IP address.
-algk
Second Gatekeeper IP address.
-gwtype
Gateway Type (0=Terminal, 1=Gateway).
-dfgw
Default Gateway IP address.
-prefix
Prefix number.
-line1
Line 1 E.164 number.
-line2
Line 2 E.164 number.
-line3
Line 3 E.164 number.
-line4
Line 4 E.164 number.
-passwd
H.235 security password.
-alias
IP side registered H323 ID.
-display String representing display information for reporting
to the called party.
-gkid
-gkdis
-ttl
-rtp
-gkfind
-gkras
-h225
-q931
-dstq931
-range
-respto
-connto
Gatekeeper ID.
Gatekeeper discovery (0=Off, 1=On).
RAS TTL time (0~3600 second).
RTP port number (1024~65532).
Gatekeeper finding port (1024~65535).
Gatekeeper RAS port (1024~65535).
H225 ras port (1024~65535).
H225 call signal port (1024~65535).
Destination H225 call signal port (1024~65535).
Dynamically allocated port range (1024~19999).
Max waiting time for 1st response to a new call (1~200).
Max waiting time for call establishment after receiving 1st
response of a new call (1~20000).
Note:
Range of IP address setting (0.0.0.0 ~ 255.255.255.255).
Example:
h323 -gk 210.59.163.171 -line1 70 -line2 71 -line3 72 -line4 73
h323 -alias Your_Alias_Name -gkid GK -gkdis 1 -passwd 1234
usr/config$
Figure 24-21 h323 commend list
- 104 -
FXS H.323 VoIP Gateway User Manual
Parameter Usages:
-print: Print current h323 related settings
-mode: Alternatives for gatekeeper or peer-to-peer mode (0=gatekeeper mode; 1=peer-to-peer
mode). If users select gatekeeper mode, an extra gatekeeper is needed when Gateway is
in operation.
usr/config$ h323 –mode 1 (peer to peer mode)
-gk: Assign gatekeeper’s IP address when Gateway is in gatekeeper mode.
-algk: Assign second gatekeeper’s IP address as redundancy. If Gateway fails to register to main
GK for 10 times, it will try to register to alternative GK.
-gwtype: Gateway type has two kinds, gateway and terminal. Gateway type: will register as
H.323 defined Gateway; user has to define [prefix] in next command. Terminal type: will
register as H.323 defined Terminal, [prefix] command is not necessary.
-dfgw: Default gateway is applied under Peer-to-Peer mode. User defines a constant default
gateway IP address, then any number dialed will pass forward to this IP Address.
-prefix: Assign VoIP Gateway prefix number, as well as the registered number on the
Gatekeeper.
-line1: Assign line 1 number.
-line2: Assign line 2 number.
-line3: Assign line 3 number.
-line4: Assign line 4 number.
Note:
User can also set “x” in line number to disable the port. If the port is disabled, it can only
receive calls but not calling out.
Line1 & line2 number must follow the prefix number if device is configured as
Gateway type.
-alias: H.323 ID. If in gatekeeper mode, this h.323 ID must be different from others who are
registering to the same gatekeeper.
-display: An addition name for user to recognize in called site.
-gkdis: Set auto discovery function on or off. If this function is enabled and IP address of
GateKeeper is set as 255.255.255.255, Gateway will multicast to search a GateKeeper on
network with configured GateKeeper name; if IP address of GateKeeper is set, before
Gateway register to the assigned GateKeeper, it will send out GRQ (GateKeeper Request)
message with configured GateKeeper name to GateKeeper first.
-gkid: Set GateKeeper name for GateKeeper discovery. When Gateway send out GateKeeper
- 105 -
FXS H.323 VoIP Gateway User Manual
discovery message will search GateKeeper with this GateKeeper name.
-rtp: To allocate RTP port range—NOT RECOMMENDED. This may be used when RTP port
range conflicts with Firewall policy (1024~65532).
-ttl: To set timer for TTL (Time To Live). Gateway would send RRQ, with keep Alive, to
gatekeeper periodically according to TTL timer, default:60 (0~3600 second).
-gkfind: Gatekeeper finding port. Which Gateway uses it to discover a gatekeeper. Default value
is 1718 (1024~65535).
-gkras: To set default gatekeeper RAS port number. Default value, is 1719 well-known port for
RAS communication.
-h225: To set the ras port.(1024~65535)
-q931: To set the call signal port.(1024~65535)
-dstq931: To specify destination H.225 signal port number.
-range: To allocate port range (1024-19999) Gateway may use it.
-respto: Maximum response time out
-connto: Maximum connection time out
-passwd: Set H.235 security password. If user’s GK need H.235 security token password to
authenticate, user have to input open password in this command.
For example:
usr/config$ h323 -print
H.323 stack relate information
RAS mode
: GK mode
Gatekeeper IP address
: 192.168.13.71
Second Gatekeeper IP
: 192.168.13.71
Gateway Type
: Gateway
Registered prefix number : 100
Line1
: 1001
Line2
: 1002
Line3
: 1003
Line4
: 1004
H.235 security token
:*
Registered alias
: 4FXS-0015db
Display Information
: 4FXS
Gatekeeper discovery
: Off
Gatekeeper ID
: GK
RAS TTL time
RTP port
: 60
: 16384
- 106 -
FXS H.323 VoIP Gateway User Manual
Gatekeeper finding port : 1718
GK RAS port
: 1719
H225 RAS port
: 1024
H225 Call signal port
: 1720
Allocated port range
:
start port
: 1024
end port
: 1043
Response timeOut
: 15
Connect timeOut
: 200
usr/config$
Figure 24-22 h323 -print commend (Gatekeeper mode)
usr/config$
H.323 stack relate information
RAS mode
Default Gateway
Line1
Line2
Line3
Line4
Alias(H323-ID)
Display Information
RTP port
: Peer-to-Peer
:x
: 000
: 001
: 002
: 003
: 4FXS-002743
: 4FXS
: 16384
H225 Call signal port
: 1720
Destination H225 call signal port : 1720
Allocated port range
:
start port
: 1024
end port
: 1043
Response timeOut
: 15
Connect timeOut
: 200
usr/config$
Figure 24-23 h323 -print commend (Peer to Peer mode)
24.7.11
[line]
Line information and configuration.
usr/config$ line
- 107 -
FXS H.323 VoIP Gateway User Manual
Gateway line information and configuration
Usage:
line [-config number [hunt number][hotline number][forward number]]
line -print
Gateway line information.
-config Set Gateway line information.
hunt: Hunting group.
hotline: Hot line configuration.
forward: No answer forward for FXS line.
Example:
line -config 1 hunt 1 hotline 1003 forward 1002
usr/config$
Figure 24-24 line commend list
Parameter Usages:
-print: print out all current settings of line
-config: determine which line to configure
--hunt: Set hunting group flag of each line. User can assign different hunt group number
represent different hunt group.
--hotline: Set hotline table. The Hotline Mode is applied in limited two channels. User
just picks up the phone set of one FXS TEL or calls in one FXO line, and gateway
will automatically dial out a phone number. In the other hand, user will hear ring
back tone or dial tone immediately depended on configurations of destination
device.-forward: Set no answer forward table.
For example:
usr/config$ line -print
Line information and configuration
Index Type Hunt Hotline
No Answer Forward Registration Status
========================================================
1
2
3
4
FXS
FXS
FXS
FXS
1
2
3
4
x
x
x
x
x
x
x
x
No
No
No
No
Ready
Ready
Ready
Ready
usr/config$
Figure 24-25 line -print commend
- 108 -
FXS H.323 VoIP Gateway User Manual
24.7.12
[prefix]
This command is for make rules for drop or insert prefix digits.
usr/config$ prefix
Prefix drop/insert information and configuration
Usage:
prefix [-print]
[-add [prefix number][drop used][insert digits]]
[-modify index [prefix number][drop used][insert digits]]
[-delete index number]
prefix -print Display drop/insert information.
-add
Add new prefix drop/insert information
prefix : The prefix of dialed number.
drop
: Drop prefix (0=Disable, 1=Enable).
insert : 1~10 digits.
-modify Modify prefix drop/insert information
index : The prefix index number record.
prefix : The prefix of dialed number.
drop
: Drop prefix (0=Disable, 1=Enable).
insert : 1~10 digits.
-delete Delete prefix index number record.
Example:
prefix -print
prefix -add prefix 100 drop 1 insert 2000
prefix -add prefix 100 drop 1
prefix -add prefix 100 drop 0 insert 200
prefix -modify 1 prefix 100 drop 0 insert 300
prefix -delete 1
usr/config$
Figure 24-26 prefix commend list
Parameter Usages:
-add: Add a rule to drop or insert prefix digits of incoming call.
--prefix: Set which prefix number to implement prefix rule.
- 109 -
FXS H.323 VoIP Gateway User Manual
--drop: Enable or disable drop function. If this function is enabled, Gateway will drop
prefix number on incoming call.
--insert: Set which digit to insert on incoming call.
usr/config$ prefix -add prefix 100 drop 1 insert 2000
-modify: Modify a rule to drop or insert prefix digits of incoming call.
usr/config$ prefix –modify 100 drop 0 insert 200
-delete: Delete a rule to drop or insert prefix digits of incoming call.
usr/config$ prefix –delte modify 100 drop 0 insert 200
For example:
usr/config$ prefix -print
Prefix drop/insert information and configuration
Index Prefix
Drop
Insert
========================================================
1
100
Enable 2000
usr/config$
Figure 24-27 prefix –print commend
24.7.13
[pbook]
Phone Book function allows users to define their own numbers, which mapping to real IP
address. It is effective only in peer-to-peer mode. When adding a record to Phone Book, users do
not have to reboot the machine, and the record will be effective immediately.
usr/config$ pbook
Phone book information and configuration
Usage:
pbook [-print]
[-add [name string][e164 number][IP address][port number]
[drop used][insert digits]]
[-modify number [name string][e164 number][IP address][port number]
[drop used][insert digits]]
[-delete number]
pbook -print
-add
Display phone book information and configuration.
Add new phone book record.
name
: 1 ~ 10 characters.
- 110 -
FXS H.323 VoIP Gateway User Manual
e164 : 1 ~ 10 digits.
ip
: IP adress.
port : 1024 ~ 65535.
drop : Drop prefix (0=Disable, 1=Enable).
insert : 1 ~ 10 digits.
-modify
Modify phone book record.
name
: 1 ~ 10 characters.
e164
: 1 ~ 10 digits.
ip
: IP adress.
port : 1024 ~ 65535.
drop : Drop prefix (0=Disable, 1=Enable).
insert : 1 ~ 10 digits.
-delete
Delete phone book index record.
Note:
Range of IP address setting (0.0.0.0~255.255.255.255).
Range of index setting value (1~100).
Example:
pbook -print
pbook -add name test e164 1234 ip 192.168.1.10
pbook -add name test e164 1234 ip 192.168.1.10 port 1720 drop 1 insert 5678
pbook -modify 1 name test e164 5678 ip 192.168.1.10 port 1720 drop 0
pbook -delete 1
usr/config$
Figure 24-28 pbook commend list
Parameter Usages:
-print: Print out current contents of Phone Book. Users can also add index number, from 1 to 100,
to the parameter to show specific phone number.
Note:
Index number: means the sequence number in phone book. If users do request a specific
index number in phone book, Gateway will give each record a automatic sequence number as
index.
-add: add a new record to phone book. When adding a record, users have to specify name, IP, and
e164 number to complete the command.
--name: Name to represent caller.
--e164: e.164 number for mapping with IP address of caller
--ip: IP address of caller
- 111 -
FXS H.323 VoIP Gateway User Manual
--port: Call signal port number of caller
--drop : Drop e.164 number when dial out. 0 means to keep e.164 number, 1 means to
drop e.164 number when dialing out.
--inert: Insert digits.(1~10 digits)
usr/config$ pbook –add name test e164 100 ip 192.168.13.78
-modify: modify an existing record. When using this command, users have to specify the
record’s index number, and then make the change.
usr/config$ pbook –modify 1 name test e164 5678 ip 192.168.1.10 port 1730 drop 0
-delete: delete a specific record. [pbook –delete 3] means delete index 3 record.
usr/config$ pbook –delete 3
PhoneBook Rules:
The e164 number defined in phone book will fully carry to destination. It is not just a
representative number for destination’s IP Address. In other words, user dial this e164 number to
reach destination, destination will receive the number and find out if it is matched to its e164,
including Line number in some particular device.
For example:
usr/config$ pbook –print
Phone book information and configuration
Index Name
E.164
IP
Port Drop
Insert
========================================================
1
test
100
192.168.13.78
1720 Disable
usr/config$
Figure 24-29 pbook -print commend
24.7.14
[voice]
The voice command is associated with the audio setting information. There are four voice
codecs supported by Gateway.
usr/config$ voice
Voice codec setting information and configuration
Usage:
voice [-print]
[-send [G723 ms] [G729 ms] [G729A ms] [G729B ms] [G729AB ms] [G711U ms]
[G
- 112 -
FXS H.323 VoIP Gateway User Manual
711A ms] ]
voice [-priority [G723] [G729] [G729A] [G729B] [G729AB] [G711U] [G711A] ]
[-volume line [voice level][input level][dtmf level]]
[-nscng [G711U used1][G711A used2][G723 used3]]
[-echo used][-mindelay t1][-maxdelay t2]
-print
-send
Display voice codec information and configuration.
Specify sending packet size.
G.723 (30/60/90 ms)
G.729
(20/40/60 ms)
G.729A (20/40/60 ms)
G.729B (20/40/60 ms)
G.729AB (20/40/60 ms)
G.711U (20/40/60 ms)
G.711A (20/40/60 ms)
-priority Priority preference of installed codecs.
G.723
G.729
G.729A
G.729B
G.729AB
G.711U
G.711A
-volume
Specify the following levels:
voice volume (0~63, default: 30),
input gain (0~63, default: 30),
dtmf volume (0~31, default: 23),
-nscng
No sound compression and CNG (G.723.1 only, 0=Off, 1=On).
-echo
Setting of echo canceller. (0=Off, 1=On, per port basis).
-mindelay Setting of jitter buffer min delay. (0~150, default: 90).
-maxdelay Setting of jitter buffer max delay. (0~150, default: 150).
Example:
voice -send g723 60 g729 60 g729a 60 g729b 60 g729ab 60 g711u 60 g711a 60
voice -volume 1 voice 20 input 32 dtmf 27
voice -echo 1 1 1 1
usr/config$
Figure 24-30 voice commend list
- 113 -
FXS H.323 VoIP Gateway User Manual
Parameter Usages:
-print: Print current voice information and configurations.
-send: To define packet size for each codec. 20/40/60ms means to send a voice packet per
20/40/60 milliseconds. The smaller the packet size, the shorter the delay time. If network
is in good condition, smaller sending packet size is recommended. In this parameter,
20/40/60ms is applicable to G.711u/a law, and G.729 codec, while 30/60ms is applicable
to G.723.1 codec.
-priority: Codec priority while negotiating with other h323 device. This parameter determines
the listed sequence in h.245 TCS message. The codec listed in left side has the highest
priority when both parties determining final codec. User can also select the particular
codec without others.
usr/config$ voice –priority g723 (only select this codec)
usr/config$ voice –priority g723 g729 g711u g711a (select four codecs, and g723 is the
first choice)
-volume: There are three adjustable value.
--voice volume stands for volume, which can be heard from Gateway side(range 0~63,
default: 28).
--input gain stands for volume, which the opposite party hears (range 0~38, default: 28).
--dtmf volume stands for DTMF volume/level, which sends to its own Line (range 0~31,
default: 23).
-nscng: Silence suppression and comfort noise generation setting (1 = ON; 0 = OFF). It is
applicable to G.723 codec only.
usr/config$ voice -nscng g723 1
-echo: On or Off the activate each canceler.
-mindelay: The minimum jitter buffer size (Default value= 90 ms).
-maxdelay: The minimum jitter buffer size (Default value= 150 ms).
usr/config$ voice –mindelay 90 –maxdelay 150
Note:
Be sure to know well the application before you change voice parameters because this
might cause incompatibility.
For example:
usr/config$ voice –print
Voice codec setting relate information
- 114 -
FXS H.323 VoIP Gateway User Manual
Sending packet size :
G.723.1
: 60 ms
G.729
: 60 ms
G.729A
: 60 ms
G.729B
: 60 ms
G.729AB
: 60 ms
G.711U
: 40 ms
G.711A
: 40 ms
Priority order codec :
g7231 g729 g729a g729b g729ab g711u g711a
Volume levels
:
voice volume : 29 28 29 28
input gain
: 36 36 36 36
dtmf volume : 23 23 23 23
No sound compress & CNG :
G.723.1
: Off
G.729
: There is no setting
G.729A
: There is no setting
G.729B
: There is no setting
G.729AB
: There is no setting
G.711(U-Law) : There is no setting
G.711(A-Law) : There is no setting
Echo canceller
: On On On On
Jitter buffer
:
Min Delay
: 90
Max Delay
: 150
usr/config$
Figure 24-31 voice –print commend
24.7.15
[support]
This command provides some extra functions that might be needed by users.
usr/config$ support
Special Voice function support manipulation
Usage:
support [-print][-t38 used][-t38ecm used][-t38asn1 used][-faxrdd digits]
[-fstart used][-tunnel used][-h245fs used][-earkyh245 used]
- 115 -
FXS H.323 VoIP Gateway User Manual
[-h450 used]
support -print Display support information and configuration.
-t38
T.38(FAX) (0=Disabled, 1=Enabled).
-t38ecm
T.38(FAX) ECM (0=Disabled, 1=Enabled).
-t38asn1 T.38(FAX) ASN.1 support (0=Disabled, 1=Enabled).
-faxrdd
FAX redundancy depth (0 ~ 2).
-fstart
Fast start (0=Disabled, 1=Enabled).
-tunnel
H245 Tunneling (0=Disabled, 1=Enabled).
-h245fs
H245 message after FastStart support (0=Disabled, 1=Enabled).
-earlyh245 EarlyH245 support (0=Disabled, 1=Enabled).
-h450
H450 support (0=Disabled, 1=Enabled).
Example:
support -t38 1
support -t38ecm 1
support -t38asn1 1
support -faxrdd 1
support -fstart 1
support -tunnel 1
support -h245fs 1
support -earlyh245 1
support -h450 1
usr/config$
Figure 24-32 support commend list
Parameter Usages:
-print: print current settings in support command.
-t38: Enable or disable T.38 fax ability. The function is will automatically defer codec (G.723 or
G.729a) to T.38 when FAX signal is detected.
-t38ecm: Enable or disable t38ecm function. The function is support the error correction in the
high-speed fax mode.
-t38asn1: Enable or disable Enable ASN.1 function. The function is support with the FAX.
-faxrdd: Set fax redundancy depth. User can increase FAX redundancy depth when network
traffic is heavy. For example, if user set fax redundancy as 2, Gateway will resend fax
packets every 2 packets.
-fstart: Enable or disable fstartStart function. The function is can shorten the connection time if
the opposite party also supports fastStart.
- 116 -
FXS H.323 VoIP Gateway User Manual
-tunnel: Enable or disable H.245 tunneling function. The function is send H.245 (Call Control
messages) via H.225’s (Call Signal messages) link. The function is effective only when
both side support h245 tunnel.
-h245fs: Enable or disable Gateway H.245 FastStart. The function is send h.245 messages after
FastStart.
-earlyh245: Enable or disable early H.245 function. The function is effective only when both
sides support early H.245.
-h450: Enable or disable H.450 related features, which include transfer, hold and forward.
Note:
It is not recommended to change the value in this command, only if users do know well the
application. This might cause incompatibility with other devices.
For example:
usr/config$ support -print
Special Voice function support manipulation
T.38(FAX) support
: Disabled
T.38(FAX) ECM
: Disabled
T.38(FAX) ASN.1
: Disabled
FAX redundancy depth : 0
FastStart support
: Enabled
Tunneling support
: Disabled
H.245 message after FastStart support : Enabled
EarlyH245 support
: Disabled
H450 support
: Disabled
usr/config$
Figure 24-33 support –print commend
24.7.16
[sysinfo]
This command could show up the line is busy or not.
usr/config$ sysinfo
System information
Index Reg. Status
=================
1
No Ready
- 117 -
FXS H.323 VoIP Gateway User Manual
2
3
4
No
No
No
Ready
Ready
Ready
usr/config$
Figure 24-34 sysinfo commend list
Note:
Index: Line channel.
Reg: Line registration Gatekeeper status. If you use registration Gatekeeper server, then
display registration status [No] or [OK].
Status: Line status in use display [busy] or not use display [Ready]. When you set h323 line
number [x] disable, the status field not check h323 line number setup.
24.7.17
[phone]
Gateway progress tone is configurable. Default tone value is set according to U.S. tone
specification. Users may adjust the values according to their own country’s tone specification or
users-defined tone specification.
usr/config$ phone
Phone ringing , ringback tone , busy tone , dial tone setting and notes
Usage:
phone [-print [ring][rbt][bt][dt][flash]]
[-ring [freq ][ringON ][ringOFF ][ringLevel]]
[-rbt [freqLo ][freqHi ][freqLoLev][freqHiLev]
[Tone1ON][Tone1OFF][Tone2ON ][Tone2OFF ]]
[-bt [freqLo ][freqHi ][freqLoLev][freqHiLev]
[Tone1ON][Tone1OFF][Tone2ON ][Tone2OFF ]]
[-dt [freqLo ][freqHi ][freqLoLev][freqHiLev]
[Tone1ON][Tone1OFF][Tone2ON ][Tone2OFF ]]
[-flash [freqLo ][freqHi ]]
phone -print Display phone ringing/tone configuration.
ring : ringing
rbt
: ringback tone
bt
: busy tone
dt
: dial tone
flash : flash tone
-ring
ringing configuration set.
- 118 -
FXS H.323 VoIP Gateway User Manual
-rbt
-bt
-dt
-flash
ringback tone configuration set.
busy tone configuration set.
dial tone configuration set.
flash configuration set.
Note:
ringing frequency
: 15 ~ 100
(Unit : Hz)
ringing ring ON/OFF : 0 ~ 8000 (Unit : ms)
ringing level
: 0 ~ 94
(Unit : V)
tone
frequency : 0 ~ 65535 (Unit : Hz)
tone
freqLevel : 0 ~ 65535 (Unit : mVrms)
tone
Tone ON/OFF : 0 ~ 8000 (Unit : ms)
Example:
phone -print rbt
phone -ring 20 2000 4000 94
phone -rbt 440 480 8 8 2000 4000 2000 4000
phone -bt 620 480 8 8 500 500 1023 1023
phone -dt 440 350 8 8 500 1023 500 1023
phone -flash 100 300
usr/config$
Figure 24-35 phone commend list
Parameter Usages:
-print: Print current call progress tone configurations (ring: ring tone, rbt: ring back tone, bt: busy
tone, dt: dial tone). This parameter should be accompanied with tone type.
-ring: To set RING tone value. The played tone type, when Gateway is receiving a call.
-rbt: To set RingBackTone value. The played tone type, when Gateway receives a Q.931 Alerting
message. In condition that Gateway is the originate side.
-bt: To set BusyTone value. The played tone type, when destination is busy.
-dt: To set DialTone value. The played tone type, when hook off a phone set of workable
Gateway.
-flash: Set the detective flash range in ms, for example, 300-500 ms.
Note:
For tone simulation, Gateway adopts dual frequencies as traditional telephone does. If users
want to have their own call progress tone, they can change the value of tones. High and Low
frequency/level/cadence can be configured respectively.
- 119 -
FXS H.323 VoIP Gateway User Manual
For example:
usr/config$ phone -print rbt
Phone ringback tone paramter
Ringback Tone frequency high
Ringback Tone frequency low
Ringback Tone frequency high level
Ringback Tone frequency low level
Ringback Tone tone1 on
Ringback Tone tone1 off
Ringback Tone tone2 on
Ringback Tone tone2 off
: 480
: 440
: 155
: 155
: 2000
: 4000
: 2000
: 4000
Figure 24-36 phone –print rbt commend
usr/config$ phone -print rbt
Phone ring back tone paramter
Ringback Tone frequency high
Ringback Tone frequency low
Ringback Tone frequency high level
Ringback Tone frequency low level
Ringback Tone tone1 on
Ringback Tone tone1 off
Ringback Tone tone2 on
Ringback Tone tone2 off
usr/config$
: 440
: 480
: 13
: 13
: 100
: 200
: 100
: 200
Figure 24-37 phone –print rbt commend
usr/config$ phone -print bt
Phone busy tone paramter
Busy Tone frequency low
Busy Tone frequency high
Busy Tone frequency low level
Busy Tone frequency high level
Busy Tone tone1 on
Busy Tone tone1 off
Busy Tone tone2 on
: 480
: 620
:8
:8
: 50
: 50
: 50
- 120 -
FXS H.323 VoIP Gateway User Manual
Busy Tone tone2 off
usr/config$
: 50
Figure 24-38 phone –print bt commend
usr/config$ phone -print dt
Phone dial tone paramter
Dial Tone frequency low
Dial Tone frequency high
Dial Tone frequency low level
Dial Tone frequency high level
Dial Tone tone1 on
Dial Tone tone1 off
Dial Tone tone2 on
Dial Tone tone2 off
usr/config$
: 350
: 440
:8
:8
: 500
: 1023
: 500
: 1023
Figure 24-39 phone –print dt commend
usr/config$ phone -print flash
Phone flash paramter
Flash frequency high : 300
Flash frequency low : 100
usr/config$
Figure 24-40 phone –print flash commend
24.7.18
[tos]
IP Packet ToS (Type of Service)/ Differentiated Service configuration.
Usr/config$ tos
IP Packet ToS (Type of Service)/Differentiated Service configuration
Usage:
tos [-print][-rtptype dscp][-sigtype dscp]
tos -print
Display IP packet Tos configuration.
- 121 -
FXS H.323 VoIP Gateway User Manual
-rtptype The packages of voice (0~63).
-sigtype The package of call signal (0~63).
Example:
tos -rtptype 7 -sigtype 0
usr/config$
Figure 24-41 tos commend list
Parameter Usages:
-rtptype: the packages of voice (0~63).
-sigtype: the package of call signal (0~63).
Note:
The value of rtptype and sigtype is from 0 to 63. It’s working if it supported by your
network.
For example:
usr/config$ tos –print
IP Packet ToS information:
Signalling Packet:
DSCP Code : 0
Media Packet
:
DSCP Code : 0
usr/config$
Figure 24-42 tos -print commend
24.7.19
[ddns]
The dynamic DNS service information and configuration
usr/config$ ddns
The dynamic DNS service information and configuration
Usage:
ddns [-print][-enable used][-server Address][-hostname Name][-id Account]
[-passwd Password][-checkip used][-checkipsrv Address][-delay time]
[-force IP]
- 122 -
FXS H.323 VoIP Gateway User Manual
ddns -print
Display Dynamic DNS information and configuration.
-enable
Use the dynamic DNS service(0=Disable, 1=Enabled).
-server
Specify DDNS server address.
-hostname
Registered domain name.
-id
Registered account ID.
-passwd
Registered account password.
-checkip
Check the host current IP address(0=Disable, 1=Enabled).
-checkipsrv1 Specify IP address check server.
-checkipsrv2 Specify secondary IP address check server.
-delay
Setting the service delay time (1~59 minutes or 1~24 horus).
-force
Force execute the dynamic DNS service.
Example:
ddns -print
ddns -enable 1
ddns -server member.dyndns.org -hostname ipphone.dyndns.org
ddns -delay 30 m (30 minutes)
ddns -delay 12 h (12 hours)
ddns -force 11.22.33.44
usr/config$
Figure 24-43 ddns commend list
Parameter Usages:
-enable: Enable or disable the DDNS function.
-server: Enter the server address of the DDNS server you use.
-hostname: Enter the domain name address which you get from the DDNS server.
-id: Enter your login DDNS server id.
-passwd: Enter your login DDNS server password.
-checkIP: Enable or disable the check current user’s IP address.
-checkIPsrv1: Enter the IP address of the check server.
-checkIPsrv2: Enter the secondary IP address of the check server.
-delay: Enable or disable the service delay time.
-force: Execute the DDNS function all the times.
Note:
Support DDNS Server: www.dyndns.org.
For example:
- 123 -
FXS H.323 VoIP Gateway User Manual
usr/config$ ddns -print
Dynamic DNS service information
Status
: Enable
Server
: www.dyndns.org
Host Name
: totoro609.dnsalias.net
ID
: totoro609
Password
: 123456789
Check IP
: Disable
IP Check Server1 : checkip.dyndns.org
IP Check Server2 : checkip.dyndns.org
Delay
usr/config$
: Off
Figure 24-44 ddns -print commend
24.7.20
[pt]
RTP payload type configuration and information
usr/config$ pt
RTP payload type configuration and information
Usage:
pt [-print][-rfc2833 type][-dtmf type][-fax type][-faxbypass type]
[-modembypass type][-redundancy type][-modemrelayp type]
pt -print
Display the RTP payload type information.
-rfc2833
Configurate the DTMF RFC2833 payload type.
-dtmf
Configurate the DTMF payload type.
-fax
Configurate the FAX payload type.
-faxbypass
Configurate the FAX ByPass payload type.
-modembypass Configurate the MODEM ByPass payload type.
-redundancy
Configurate the Redundancy payload type.
-modemrelay
Configurate the MODEM Relay payload type.
Example:
pt -rfc2833 96 -fax 101
usr/config$
Figure 24-45 pt commend List
- 124 -
FXS H.323 VoIP Gateway User Manual
For example:
usr/config$ pt -print
RTP payload type information
RFC2833 payload type
: 96
DTMF payload type
: 100
FAX payload type
: 101
FAX ByPass payload type
: 102
MODEM ByPass payload type : 103
Redundancy payload type
: 104
MODEM Relay payload type : 105
usr/config$
Figure 24-46 pt -print commend
24.7.21
[rom]
ROM file information and firmware upgrade function.
usr/config$ rom
ROM files updating commands
Usage:
rom [-print][-app][-boot][-boot2m][-dsptest][-dspcore][-dspapp]
[-s TFTP/FTP server ip][-f filename][-method used]
[-ftp [username][passwd]]
rom -print
Show versions of rom files (optional).
-app
Update main application code (optional).
-boot
Update main boot code (optional).
-boot2m
Update 2M code (optional).
-dsptest Update DSP testing code (optional).
-dspcore Update DSP kernel code (optional).
-dspapp
Update DSP application code (optional).
-s
IP address of TFTP/FTP server (mandatory).
-f
File name (mandatory).
-method
Download via TFTP/FTP (0=TFTP, 1=FTP)
-ftp
specify username and password for FTP.
Note:
- 125 -
FXS H.323 VoIP Gateway User Manual
This command can run select one option in 'app', 'boot',
'dsptest', 'dspcore', and 'dspapp'.
Example:
rom -method 1
rom -ftp vwusr vwusr
rom -app -s 192.168.4.101 -f app.bin
usr/config$
Figure 24-47 rom commend List
Parameter Usages:
-print: show versions of all rom files
-app, boot, boot2m, dsptest, dspcore, dspapp: To update main Application program code, Boot
code, DSP testing code, DSP kernel code, or DSP application code.
Note:
Most of all, the Rom file needed to get upgrade is App or Boot2m. Please check the
exactly Rom file before doing download procedure.
-s: To specify TFTP server’s IP address when upgrading ROM files.
-f: To specify the target file name, which will replace the old one.
-method: To decide using TFTP or FTP as file transfer server. [0] stands for TFTP, while [1]
stands for FTP.
-ftp: If users choose FTP in above item, it is necessary to specify pre-defined username and
password when upgrading files.
For example:
usr/config$ rom –print
Download Method : TFTP
Boot Rom
Application Rom
DSP App
DSP Kernel
DSP Test Code
:
:
:
:
:
sdboot.200
4afxs.204.bin
48302ce3.140
48302ck.140
483cbit.bin
usr/config$
Figure 24-48 rom –print commend
- 126 -
FXS H.323 VoIP Gateway User Manual
24.7.22
[passwd]
For security concern, users have to input the password before entering configuration mode.
[passwd] command is for password setting purpose.
usr/config$ passwd
Password setting information and configuration
Usage:
passwd [-set [Login name] [Password]][-clean]
passwd -set
Loginname Password.
-clean Clear all password stored in flash.
Note:
1. Loginname can be only 'root' or 'administrator'
2. passwd -clean will clear all passwd stored in flash,
please use it with care.
Example:
passwd -set root Your_Passwd_Setting
passwd -clean
usr/config$
Figure 24-49 passwd commend List
Parameter Usages:
–set: Set login name and password, input login name then input new password.
-clean: Will clear all password setup, and change null.
Note:
Gateway Login name only use [root] or [administrator]. [root] and [administrator] have the
same authorization, except commands that can be excuted by [Login name: root] only
[passwd –set root], [rom –boot], [room-boot2m] and [flash –clean].
For example:
usr/config$ passwd -set root root1234
Setting
login: root
Password: root1234
OK
usr/config$
Figure 24-50 passwd –set commend
- 127 -
FXS H.323 VoIP Gateway User Manual
sr/config$ passwd -clean
Please wait a moment!!
Clean password OK.
usr/config$
Figure 24-51 passwd –clean commend
- 128 -