Extron electronics | DVS 406 | DVS 406 SDI Card - Extron Electronics

4.
Insert the card’s installation screw through the SDI card’s
mounting hole, and gently tighten it into the standoff.
User’s Guide
Fig. 4 — SDI card mounted in place
5.
Install the SDI connector’s hex nut from the outside of the
rear panel opening. Keep the SDI card from twisting as the
nut is tightened.
6.
Replace the top cover on the DVS 406 scaler, and fasten it
with the screws which were removed in step 3 of the
“Internal access” section.
7.
Rack/furniture mount the scaler, and reconnect the AC
power cord.
Part Numbers
Extron Part
SDI Input Card Kit
Part Number
70-168-01
DVS 406 SDI Input Card
70-168-01 Upgrade Kit
www.extron.com
Extron Electronics, USA
Extron Electronics, Europe
Extron Electronics, Asia
Extron Electronics, Japan
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
© 2002 Extron Electronics. All rights reserved.
68-619-01 Rev. B
Printed in the USA
08 02
Installation
Installing the SDI Connector Card
Card installation
The SDI connector card may be installed in the DVS 406 by
following the instructions and illustrations shown below.
After following the instructions in “Internal access” to remove
the cover, do the following:
1.
Internal access
To gain access to the internal components, do the following:
1.
Locate the SDI card standoff located near the middle rear
portion of the main circuit board (looking from above with
the front panel nearest to you).
Remove the power cable from the DVS 406 and from the
power source.
SDI connector opening
Do not open the cover of the scaler without
unplugging the power cord.
2.
If the DVS 406 scaler is rack mounted, remove the input and
output cables from it and remove the unit from the rack. If
the scaler is not rack mounted, you do not need to remove
the input and output cables.
3.
Remove 13 screws from the top and sides of the cover
(figure 1).
Remove (13)
screws from
top and sides
SDI card standoff
Fig. 2 — SDI card standoff and connector opening
ST
JU
AD
MEN
Lift Cover
Straight Up
O
ITAL
TS
MEN
ST
JU
AD
ER
NT
CE
SIZE
IL
DE
ON
T/C
BR
L/T
CO
NT
6
KE
TA
5
4
I
SD
3
O/
O
VIDE
DE
V VI
YU S-
O/
O
VIDE
VIDE
S-
O/
O
VIDE
VIDE
S-
B/
RG
B
RG
Fig. 1 — Removing the cover
4.
3.
The SDI card has a 20-pin socket on the underside which
must align with the 20 pins on the main circuit board. Be
sure to align the pins properly, in order to prevent bending
the pins, before pressing the SDI card firmly in place against
the standoff. The mounting hole on the SDI card should
now be directly over the standoff.
XT
TA
T
2
Remove the plastic cap covering the SDI connector opening
from the rear panel of the scaler, and position the SDI card
at an angle with the SDI connector protruding from the rear
SDI connector opening.
SC
VIDE
DIG
NE
RE
TU
PIC
1
2.
6
S 40
DV ALER
U
Remove the cover by slightly lifting each side alternately
until the cover is free.
20-pin socket on
back of SDI card
Reverse this procedure to reinstall the cover after the SDI
connector card has been installed.
CAUTION
2
Do not touch any switches or other electronic
components inside the scaler. Doing so could damage
the scaler. Electrostatic discharge (ESD) can damage
IC chips even though you cannot feel it. You must be
electrically grounded. A grounding wrist strap is
recommended.
DVS 406 SDI Input Card • Installation
20-pin connector
on main board
Fig. 3 — SDI card situated above pins and standoff
DVS 406 SDI Input Card • Installation
3
Download PDF