Acura | 2008 MDX | BII37607-39736 2008 MDX Running Board Sport.pmd

INSTALLATION
INSTRUCTIONS
Accessory
Application
RUNNING BOARDS (SPORT)
P/N 08L33-STX-200C
2009 MDX
PARTS LIST
Publications No.
BII 39905
Issue Date
JULY 2008
4 Flange nuts, 6 mm
Right running board
2 Brackets A
Left running board
4 Brackets B
24 Flange bolts
Right front end cap
12 Flange nuts, 8 mm
Left front inner end cap
Left front end cap
Right front inner end cap
Right rear end cap
Left rear end cap
Right bracket C
8 Self-tapping screws
Left Bracket C
4 Screws
2 Bumper bolts
4 Washers
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
BII 39905 (0807)
08L33-STX-2C00-91
1 of 4
2.
TOOLS AND SUPPLIES REQUIRED
Ratchet
10 mm and 13 mm Sockets
10 mm and 13 mm Combination wrenches
Install bracket A and two brackets B to the holes
in the bottom of the side sill trim with 12 flange
bolts. Thread the flange bolts in about three or four
turns, but do not tighten.
NOTE: If there is undercoat on the body surface,
remove the undercoat using a scraper or
equivalent tool before installing the bracket A. If
necessary, clean the threads using a tap. Take
care not to damage the paint finish.
Blanket
Torque wrench
Swivel socket
90 degree screwdriver
INSTALLATION
FRONT
Client Information: The information in this
instruction is intended for use only by skilled
technicians who have the proper tools, equipment,
and training to correctly and safely add equipment to
your vehicle. These procedures should not be
attempted by “do-it-yourselfers.”
BRACKET B
NOTE:
•
Thoroughly clean the bottom of the body between
the front and rear wheels.
•
Be careful not to damage the body paint finish. To
prevent damage, place a blanket under the running
board during the installation.
•
These instructions show the left side running
board being installed; the same procedure applies
to installing the right running board.
1.
Remove the left front splash guard (5 self-tapping
screws).
12 FLANGE BOLTS
BRACKET A
5N19050T
3.
Loosely install bracket C (left) to the hole in the
bottom of the left side sill trim using the self
tapping screw removed in step 1.
LEFT
FRONT
SPLASH
GUARD
LONG
SELFTAPPING
SCREW
(Discard.)
3 LONG SELF-TAPPING
SCREWS
(Reuse.)
2 of 4
LEFT SIDE SILL
TRIM
SHORT
SELF-TAPPING
SCREW
(Reuse.)
SHORT
SELF-TAPPING
SCREW
(reused)
BRACKET C
5N19060T
5N19011T
BII 39905 (0807)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
4.
Install the left front end cap and the left rear end
cap to the left running board with the two selftapping screws, two washers, one screw, and one
6 mm flange nut. Install the left rear end cap the
same way. The left rear end cap does not use
washers.
5.
Align the bolts on the left running board to the
holes in brackets A and B you just installed
on the side sill trim, and install it by loosely
tightening six 8 mm flange nuts.
BRACKET B
FRONT
FRONT
LEFT RUNNING
BOARD
LEFT FRONT
END CAP
WASHERS
BRACKET A
LEFT
RUNNING
BOARD
6 LEFT RUNNING
BOARD BOLTS
SCREW
6 FLANGE
NUTS, 8 mm
6 mm
FLANGE
NUT
5N19031T
SELF-TAPPING
SCREWS
6.
REAR
Align the left front inner end cap to the front of the
left running board, and install it by loosely
tightening a bumper bolt.
LEFT RUNNING
BOARD
LEFT RUNNING
BOARD
LEFT REAR
END CAP
SCREW
LEFT
FRONT
INNER
END CAP
BUMPER
BOLT
6 mm
FLANGE
NUT
SELF-TAPPING
SCREW
5N19090T
BRACKET C
LEFT
END
CAP
FRONT
BUMPER
BOLT
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
BII 39905 (0807)
Side view
5N19070T
3 of 4
7.
While pushing up on the running board, secure the
left front inner end cap with the three long selftapping screws.
Make sure there is
no gap in this area.
LEFT
FRONT
INNER
END
CAP
Push up
LEFT
RUNNING
BOARD
3 LONG SELFTAPPING SCREWS
(reused)
8.
Torque all the bolts and nuts you installed in step
2 and step 5. Torque the flange bolts to 27 N·m
(20 lb-ft). Tighten the screw you installed in step
3.
9.
Repeat steps 1 through 8 to install the right
running board.
4 of 4
BII 39905 (0807)
© 2008 American Honda Motor Co., Inc. - All Rights Reserved.
Download PDF