Delta | PD-01 | User manual | Delta PD-01 User manual

PD-01 USER MANUAL
PROFIBUS-DP Module for
VFD Series Drives
ASIA
DELTA ELECTRONICS, INC.
TAOYUAN Plant/
31-1, SHIEN PAN ROAD,
KUEI SAN INDUSTRIAL ZONE
TAOYUAN 333, TAIWAN
TEL: 886-3-362-6301
FAX: 886-3-362-7267
http://www.delta.com.tw/acdrives
EUROPE
NORTH/SOUTH AMERICA
DELTRONICS (Netherlands)
DELTA PRODUCTS
B.V.
CORPORATION
Sales Office/
Sales Office/
Industriegebied Venlo Nr. 9031
P.O. BOX 12173
Columbusweg 20
5101 DAVIS DRIVE
NL-5928 LC Venlo
RTP, NC 27709 U. S. A.
The Netherlands
TEL: 1-919-767-3813
TEL: 31-77-324-1930
FAX: 1-919-767-3969
http://www.deltaww.com/acdrives FAX: 31-77-324-1931
PD-01 PROFIBUS-DP Module
Table of Contents
Preface .............................................................................................................. 1
Chapter 1
Overview ...................................................................................... 3
Technical information.................................................................................... 4
Functionality ................................................................................................. 4
Chapter 2
Introduction ................................................................................. 5
PROFIBUS ................................................................................................... 5
PROFIBUS-DP ............................................................................................. 6
Chapter 3
Installation ................................................................................... 7
Installing the PD-01 ...................................................................................... 7
Removing the PD-01 .................................................................................... 9
PIN assignment of PROFIBUS-DP interface (DB9)...................................... 9
Terminator..................................................................................................... 9
Chapter 4
Communication ........................................................................... 11
PROFIBUS address ..................................................................................... 11
Parameters setting in VFD series Drives...................................................... 11
Cyclical data of PD-01 via PROFIBUS-DP ................................................... 12
Useful data structure as defined in PROFIDrive Profile 2.0.................... 12
Extended configuration........................................................................... 12
Default settings of PZD structure............................................................ 13
Control and Status words ....................................................................... 13
Accessing parameters via PKW area ..................................................... 15
PKE ............................................................................................... 15
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
IND ................................................................................................ 16
Parameter value (PWE) 3rd and 4th word .................................... 16
Examples for PKW mechanism..................................................... 17
Response time about PD-01 ........................................................................ 19
Chapter 5
User Parameters Setting in GSD file ......................................... 21
GSD file ........................................................................................................ 21
User parameters in GSD file......................................................................... 25
Chapter 6
Troubleshooting .......................................................................... 29
Troubleshooting via LED displays ................................................................ 29
Troubleshooting via diagnostic data ............................................................. 30
Troubleshooting via error codes ................................................................... 31
Chapter 7
Dimensions .................................................................................. 33
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Preface
Thanks for using DELTA PD-01 PROFIBUS-DP Module. Please read this manual carefully
prior to use the PD-01 to ensure its operation properly. Please keep this manual in handy
place for quick reference.
Getting Start
This manual is intended be used as an instruction manual and a reference guide.
Detailed description of PROFIBUS and DP protocol will not be covered here. If you are
interested in understanding and learning more about the PROFIBUS and DP protocol, we
recommend you study the related comprehensive literatures.
The content in this manual is based upon the most updated hardware and software
information that are published recently. Therefore, please understand no guarantee will
be given that no any discrepancy in this manual. Moreover, We reserve the right to modify
this manual without any written notice, or any obligation to notify the end users for
revision changes.
Copying or reproducing any part of this manual, without written consent of Delta
Electronics Inc. is prohibited.
WARNING
Failure to read, fully understand and implement the instructions contained in
this manual may result in damage the equipment, the drive or a possible of plant
personnel injury.
This equipment operates under higher voltages, to control of a running machine.
Only suitable qualified personnel familiar with the operation and construction of
the equipment are allowed for equipment operation, to prevent any damage or
hazard of this equipment.
A successful and safe operation of this equipment depends upon the proper
handling, storage, installation, operation and maintenance.
1
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Receiving and Inspection
All Delta PD-01 have gone through rigorous quality control tests at the factory prior to the
shipment. Upon the receive of PD-01, please check that the package includes:
◆
1pcs PD-01,
◆
1pcs 8cm disc (mini size compact disc),
◆
1pcs communication cable (for RJ11, 6 pins),
◆
1 instruction sheet
Using this Manual
◆
This is the User Manual for PD-01.
◆
Chapter 1 describes the overview of PD-01
◆
Chapter 2 briefly describes the introduction to PROFIBUS and PROFIBUS-DP
◆
Chapter 3 introduces how to install and remove the PD-01
◆
Chapter 4 describes the communication with PROFIBUS-DP system
◆
Chapter 5 introduces GSD file and parameter settings in GSD file of PD-01
◆
Chapter 6 provides LEDs information, and corrective actions for problem
solving.
◆
Chapter 7 provides the dimensions of the PD-01
◆
Firmware version should conform with VFD Drives as table below:
Delta AC Drive
VFD-B
VFD-M
VFD-F
VFD-L
115V/200~400W
230V/200W~2HP
VFD-S
Firmware Version
Version 4.00 and above
Version 3.00and above
Version 1.09 and above
All Version
All Version
2
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Chapter 1 Overview
PD-01, defined as a communication module for PROFIBUS-DP, is used to link VFD series
Drives and PROFIBUS-DP system.
Screw Mounting Hole
SP LED
NET LED
Extended Socket
Address Switches
Profibus DP Interface (DB9)
RS-485 Interface (RJ11)
Screw Mounting Hole
SP LED: Indicating the connection status between Drives and PD-01
NET LED: Indicating the connection status between PD-01 and PROFIBUS-DP
Address Switches: Setting the address of PD-01 on PROFIBUS-DP network
RS-485 Interface (RJ11): Connecting to VFD Drives, and supply power to PD-01
PROFIBUS-DP Interface (DB9): 9-PIN connector that connects PD-01 to
PROFIBUS-DP network
Extended Socket: 4-PIN socket that connects PD-01 to PROFIBUS-DP network
Screw Mounting Hole: Used to mount PD-01
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
3
PD-01 PROFIBUS-DP Module
Technical information
Two LEDs on PD-01 used to display the connection status of PD-01:
SP LED: indicating the connection status between PD-01 and VFD series Drives
NET LED: indicating the connection status between PD-01 and PROFIBUS-DP
% For more information of LEDs display, refer to Chapter 6. Troubleshooting.
The address in PROFIBUS-DP can be set via two rotary address switches, ADDH
and ADDL, on PD-01:
ADDH used as a high 4 bits of address, ADDL used as a low 4 bits of address.
% For more information of address switches, refer to Chapter 4. Communication.
A specific 6-PIN communication cable for RJ11, is used to connect the PD-01 to
VFD series Drives via RS-485 interface. VFD series Drives supply the 15V DC
power to PD-01 through this cable.
PROFIBUS-DP interface (DB9) uses a standard PROFIBUS-DP system interface.
We recommend users use the standard connector to connect PD-01 to
PROFIBUS-DP system. Besides, the PD-01 also provides a 4-PIN extended socket
for users to connect it to PROFIBUS-DP system based upon the requirements.
However, please pay attention to the assignment of A1, B1, and A2, B2 on the
4-PIN extended socket.
PD-01 supports baud rates of 9.6kbaud to 12Mbaud.
Functionality
Cyclical process data exchange (PZD).
Parameter accessing: cyclical accessing of parameters (PKW).
PROFIBUS supports the control commands SYNC and FREEZE for data
synchronization between master and slaves.
Support the configuration of data structure for data exchange with VFD series
Drives.
4
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Chapter 2 Introduction
PROFIBUS
PROFIBUS is an international, vendor- independent, opening filed bus standard for a wide
range of applications in the fields of manufacturing, production, process and building
automation, and other automation control field.
The PROFIBUS family comprises three types of protocol, PROFIBUS-DP, PROFIBUS-PA and
PROFIBUS-FMS, each of them is used for different tasks:
PROFIBUS-DP (Decentralized Periphery): PROFIBUS-DP is a rapid and low cost
communication connection designed for high-speed data transmission at field level.
PROFIBUS-DP has widespread usage for such items as remote I/O systems, motor
control centers, and variable speed drives. It is designed and optimized especially for
communication between automation systems and decentralized peripheral devices.
PROFIBUS-PA (Process Automation): PROFIBUS-PA is the PROFIBUS solution for
process automation, typically with MBP-IS transmission technology. Based upon
PROFIBUS-DP, PROFIBUS-PA is an extension of the PROFIBUS-DP protocol for data
transmission. It is designed to support intrinsically safe applications and can be used
within hazardous areas, with high explosion risk using intrinsic safe MBP-IS interface.
PROFIBUS-PA is used to connect sensor and controller to the bus.
PROFIBUS-FMS (Fieldbus Message Specification): PROFIBUS-FMS is multiple
master communications designed for communication at the cell level. It is designed for
acyclic or cyclic data transfers at medium speed between control equipment and
cell-level controllers. FMS services open up a wide range of applications and offer a
wide range of functionality and flexibility.
The Maximum cable length in a segment depends on the transmission speed. PROFIBUS-DP
communicates at speeds from 9.6 Kbps to 12 Mbps over distances from 100 to 1,200 meters.
Baud Rate
187.5K
500K
1.5M
12M
9.6K
19.2K
93.75K
(bps)
Length (m)
1200
1200
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
1200
1000
5
400
200
100
PD-01 PROFIBUS-DP Module
PROFIBUS-DP
PROFIBUS-DP is a PROFIBUS communication profile optimized for high-speed, time-critical
data transmission at field level using low-cost connections. PROFIBUS-DP is a suitable
substitute for conventional, costly parallel wiring of 24 V measurement signals in production
and manufacturing automation, as well as for analog 4(0) to 20mA measurement signals in
process automation.
6
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Chapter 3 Installation
IMPORTANT NOTE:
Prior to the installation or remove the PD-01 from network, make sure the power of VFD
series Drives is switched off (not-energized).
Installing the PD-01
Improper installation of the PD-01 will cost its life usage. Please follow the instructions to
install your PD-01 carefully.
DIN Rail Installation
PD-01 can be secured by mounting to DIN rail. There is a small retaining clip locates at
the bottom of PD-01, place the PD-01 onto the DIN rail and gently push up on the clip to
ensure the PD-01 is mounted to the DIN rail.
Direct Mounting
Please use the specified M4 screws to install the PD-01. Also please ensure to tighten
them properly.
DIN RAIL
Screw
Mounting
Hole
CLIP
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
7
PD-01 PROFIBUS-DP Module
Insert the connector into the PROFIBUS-DP Interface (DB9), and tighten screws to
secure the connector in place.
Power Supply
The power of PD-01 is supplied from VFD series Drive. Firmware version should
conform the VFD series Drives as table listed in the page 2. No external power
needed. The +15VDC power is applied to PD-01 directly via a specific 6-PIN
communication cable (This 6-PIN cable is packed together with PD-01).
NOTE:
Though the PD-01 power is supplied from VFD series Drives, it will energized till power to
VFD series Drives is applied
RJ11
+15V
1: +15V
3: SG5: not used
GND
6
1
2: GND
4: SG+
6: not used
SGSG+
8
Not used
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
If the connection of PD-01 to VFD drives does not conform the table listed in page 2, users
need to provide external 15VDC supply the power to PD-01 (not through the communication
cable). Refer to the pin assignment of RJ11, it is allowed to supply power to PD-01 via RJ11.
PD-01 is energized while the power is applied to the VFD series Drives, then the SP
LED will be steady green.
Removing the PD-01
To remove the PD-01, users shall:
Remove the connection cable between PD-01 and VFD series Drives.
Loose the PD-01 screws and remove DP connector from PD-01.
Pull down on the retaining clip and pull out the PD-01 from DIN rail gently.
Pin assignment of PROFIBUS-DP interface (DB9)
Use PROFIBUS-DP interface (DB9) of PD-01 connecting PD-01 to PROFIBUS DP system.
The terminals are short-circuit-proof and isolated.
9
5
6
1
Pin
1
2
3
4
5
6
7
8
9
Designation
Rxd/TxD-P
DGND
VP
RxD/TxD-N
-
Meaning
Not assigned
Not assigned
Receive/send data P (B)
Not assigned
Data reference potential (C)
Supply voltage positive
Not assigned
Receive/send data N (A)
Not assigned
Terminator
Bus terminator is important when connects PD-01 to PROFIBUS-DP system. This terminator
can be switched in and out via switches when the recommended bus connectors have been
used.
If extended 4-PIN socket for the connection is used, user may use the internal terminator
provided by PD-01 via setting the switch. If the switch is turned to "S" (Short), the internal
terminator is disabled, then A1 and A2, B1 and B2 are all normally close. If the switch is
turned to "R" (Resistor), the internal terminator between A1 and B1 is enabled, but A2 and B2
are disconnected from bus.
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
9
PD-01 PROFIBUS-DP Module
A2
A1
Terminator
switch for A1/B1
B2
B1
S
R
121ohm
When user uses the extend socket, the bus topology is as follows:
PLC
Green
Red
(master)
Green
A1
B1
A2
B2
Green
A1
B1
Red
A2
B2
Red
A1
B1
A2
B2
PD-01
PD-01
PD-01
VFD
series
Drive
VFD
series
Drive
VFD
series
Drive
10
Green
Red
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Chapter 4 Communication
NOTE:
Before reading this chapter, make sure you read chapter 3 and understand the installation of
PD-01.
PROFIBUS address
PD-01 has two rotary switches to set the PROFIBUS address, the only way
for user to set the address.
The address switches, ADDH and ADDL, allow user to set the address in a
HEX format. ADDH is used to set high 4 bits of address, and ADDL is used
to set low 4 bits of address. If both ADDH and ADDL are set to F, and PD-01
is power ON or re-power ON, then PD-01 will enter the TEST mode, the SP
LED and NET LED will be in steady orange.
Address
1..0x7D
0 or
0x7E..0xFE
0xFF
Meaning
Valid PROFIBUS address
Invalid PROFIBUS address
Enter TEST mode
NOTE:
Setting changes via address switches will not effective when PD-01 is operating. This means
the setting changes will effective after PD-01 power re-boot. Please understand this cold
restart must be initiated by toggling the power to OFF and then ON.
Parameters setting in VFD series Drives
PD-01 is designed to communicate with VFD series Drives via MODBUS communication port.
Prior to the connection, users have to set parameters below in VFD series Drives:
Set the communication protocol of VFD series Drives to RTU 8, N, 2.
Set the baud rate of VFD series Drives to 9600bps.
Set the frequency source for VFD series Drives to operate via RS485.
Set the operation source of VFD series Drives via MODBUS communication.
Refer to the following table for the above settings when connecting to VFD series Drives:
VFD-L type
VFD-B / VFD-S
VFD-M type
VFD-F type
115V/200~400W
type
230V/200W~2HP
P89=01
P09-01=1
P09-01=1
P09-01=1
Baud Rate 9600
P92=03
P09-04=3
P09-04=6
P09-04=2, P09-05=0
RTU 8,N,2
P00=04
P02-00=4
P02-00=4
P02-00=4
Freq. Source
P01=03
P02-01=3
P02-01=3
P02-01=3
Command Source
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
11
PD-01 PROFIBUS-DP Module
After these settings completed, connecting PD-01 and VFD series Drives via communication
cable mentioned earlier, PD-01 is then energized. Two LED will be firstly in orange because
PD-01 is initialized and test itself. SP LED will be then in steady green since that the
connection is established between PD-01 and VFD series Drives.
Cyclical data of PD-01 via PROFIBUS-DP
PD-01 is controlled via cyclical PROFIBUS-DP channel. This channel can be used to access
the parameters of VFD series Drives.
Useful data structure as defined in PROFIDrive Profile 2.0
The structure of useful data for the cyclical channel is defined in the PROFIDrive Profile,
version 2.0. Please refer to the Parameter Process data Object (PPO).
PKW
PKE
IND
1st
2nd
word word
PPO1
PPO2
PZD
3rd
4th
PZD1
STW
ZSW
1st
word
word
word
PWE
PZD2
HSW
HIW
2nd
word
PZD3
PZD4
PZD5
PZD6
PZD7
PZD8
PZD9
PZD10
3rd
4th
5th
6th
7th
8th
9th
10th
word
word
word
word
word
word
word
word
PPO3
PPO4
PPO5
PKW: Parameter ID/value
PZD: Process data
PKE: Parameter ID
IND: Sub-index
PWE: Parameter value
STW: Control word
ZSW: Status word
HSW: Main setpoint
HIW: Main actual value
NOTE:
PD-01 supports PPO1 and PPO3 structure only.
Extended configuration
In addition to the PPO types, cyclical data can also be configured to EXT CONF 1 or EXT
CONF 2 (see table below). These two extended configuration both have four process
data words. The areas of consistency can be set flexibly.
PKW
PKE
1
st
PZD
IND
2
nd
word word
EXT CONF 1
PWE
3
rd
word
4
th
word
PZD1
STW
ZSW
st
1
PZD2
HSW
HIW
nd
2
word
word
PZD3
3
rd
word
PZD4
4
th
word
PZD5
5
th
word
PZD6
6
th
word
PZD7
7
th
word
PZD8
8
th
word
PZD9
9
th
word
PZD10
10
th
word
EXT CONF 2
12
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Default settings of PZD structure
PD-01 must receive the user parameters from master that configured via GSD file. The
default settings of PZD structure are as follows:
STW1: Control Word, mapping to MODBUS address 0x2000 of VFD series Drives.
HSW: Main set point, mapping to MODBUS address 0x2001 of VFD series Drives.
ZSW: Drives status, mapping to MODBUS address 0x2101 of VFD series Drives.
HIW: Main command frequency, mapping to MODBUS address 0x2102 of VFD series
Drives.
DP master -> VFD series Drives:
PZD3: No default assignment
PZD4: No default assignment
VFD series Drives-> DP master:
PZD3: Output frequency, mapping to MODBUS address 0x2103 of VFD series Drives.
PZD4: Output current, mapping to MODBUS address 0x2104 of VFD series Drives.
Control and Status words
PD-01 supports the PPO1 and PPO3 data structure. However, it does not support the bit
assignments of control and status words in PROFIDRV. It only supports the DELTA VFD
series Drives control and status words.
Control word (data from DP to VFD series Drives)
00: No function
01: Stop
b1-b0
10: Run
11: JOG+Run
b3-b2
Not used
00: No function
01: FWD
b5-b4
10: REV
11: Change direction
00: 1st Accel / Decel time
01: 2nd Accel / Decel time
b7-b6
10: 3rd Accel / Decel time
11: 4th Accel / Decel time
0000: Main speed
0001: 1st speed
b11-b8
0010: 2nd speed
0011: 3rd speed
0100: 4th speed
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
13
PD-01 PROFIBUS-DP Module
b11-b8
b12
b14-b13
b15
0101: 5th speed
0110: 6th speed
0111: 7th speed
1000: 8th speed
1001: 9th speed
1010: 10th speed
1011: 11th speed
1100: 12th speed
1101: 13th speed
1110: 14th speed
1111: 15th speed
1: Enable b11-b6
00: No function
01:Operation command controlled by PU
10:Operation command by Pr. setting
11:Switch between PU and Pr. setting
Not used
NOTE:
Table above is for reference only, please check VFD series Drives user manual for
details. The control word that is mapping to the address of VFD series Drives can be
carried out by PD-01, so the bit assignments in the user manual of VFD series Drives is valid.
Status word (data from VFD series Drives to DP)
00: RUN LED light off, STOP LED light up (Drive Stop)
b1-b0
b2
b4-b3
b5
b6
b7
b8
b9
b10
b11
b12
b15-b13
01: RUN LED blink, STOP LED light up (Drive Decelerate
during the drive stopping)
10: RUN LED light up, STOP LED blink (Drive standby)
11: RUN LED light up, STOP LED light off (Drive Run)
1: JOG is active
00: REV LED light off, FWD LED light up (Forward)
01: REV LED blink, FWD LED light up (Reverse to Forward)
10: REV LED light up, FWD LED blink (Forward to Reverse)
11: REV LED light up, FWD LED light off (Reverse)
1: Reserved parameters opened
Reserved
Reserved
1: Main frequency controlled by communication
1: Main frequency controlled by external terminal (EXT)
1: Operation command controlled by communication (PU)
1: Parameters have been locked
Copy command enable
Reserved
14
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
NOTE:
Table above is for reference only, please check VFD series Drives user manual for
details. PD-01 will get the status word from VFD series Drives, so the bit assignments in
the user manual of VFD series Drives is valid.
Accessing parameters via PKW area
In cyclical data, PD-01 can provide request and response (read / write) message to
access the parameters of VFD series Drives. Due to the request and response
mechanism, the master must send the request until it receives a corresponding
response.
PKW have at least 4 words:
Word 1 Parameter ID (PKE)
15
12
11
10
AK
SPM
Parameter number (PNU)
Word 2 Parameter sub-index (IND)
15
8 7
Word 3 PWE1
reserved in PD-01
Word 4 PWE2
parameter value of read/write
PKE
Bits 0 to 10 (PNU) contain the number of the relevant parameter.
Bit 11 is reserved.
Bits 12 to 15 (AK) contain the request or the response identifier.
Request identifier (master
PD-01)
Request Identifier
Meaning
0
No request
1
Request parameter value
2
Modify parameter value (word)
Response identifier (PD-01
master)
Response Identifier
Meaning
0
No response
1
Transfer parameter value (word)
7
Cannot process request (with error number)
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
15
0
0
PD-01 PROFIBUS-DP Module
Fault numbers for "Cannot process request" response
NO.
Meaning
0
Illegal Parameter number
Parameter does not exist
Parameter value cannot Parameter is a read-only parameter
be modified
or can not change in current state
Minimum/maximum not
reached / exceeded
Other error
1
2
18
IND
Structure of IND for cyclical communication via PPOs
PKE
HIGH
15
14
IND
LOW
HIGH
12
11-8 7
13
PWE1
LOW
HIGH
PWE2
LOW
HIGH
LOW
0
Para Page selection Not used
20 23 22 21
0
Function of Parameter Page Selection
Basic PNU
(B.PNU bit 10-0 of PKE)
Page selection
(P.PNU)
Total PNU
(B.PNU+P.PNU*2000)
0…1999
0
0…1999
0…1999
1
2000…3999
0…1999
2
4000…4999
…
…
…
0…1999
15
30000…31999
NOTE:
In IND, Bit 15 uses a multiplier of 20, so the value of Bit 15 for the access P2000P3999 must be set to 1.
Parameter value (PWE) 3rd and 4th word
All parameters in VFD series Drives are 16-bit. A 16-bit parameter value is transferred
in PWE2 (4th word). PWE1 (3rd word) must be set to 0 on the PROFIBUS-DP master
in this case.
16
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Examples for PKW mechanism
Example 1: Read data of parameter P0003
To read value of P0003, set the request ID to 1 (request parameter value - word).
Because P0003 is less than 2000, the Para Page Select is 0, thus, the data sequence
are as follows:
Master
PD-01 : 1003 0000 0000 0000
PD-01
Master : 1003 0000 0000 1770
Request
request value of P0003
Response
Word 1 (PKE)
1003
Word 1 (PKE)
1003
Word 2 (IND)
0000
Word 2 (IND)
0000
Word 3 (PWE1)
0000
Word 3 (PWE1)
0000
Word 4 (PWE2)
0000
Word 4 (PWE2)
1770
PD-01 responds the value of P0003. All parameters in VFD series Drives are 16-bit
value, so the value is transferred in PWE2 (4th word). The value of P0003 is 0x1770
(6000 decimal), in VFD-M series Drives, it is “Maximum Output Frequency”.
Example 2: Read command frequency in VFD series Drives (0x2102)
To read value of command frequency, set the request ID to1, we should set the Para
Page Select because the parameter address is greater than 2000. The address
0x2102 is 8450 in decimal, if set Page Select to 4, then the Basic PNU is 8450 –
4*2000 = 450 (0x1c2), thus, the data sequence are as follows:
Master
0x2102
PD-01 : 11C2 2000 0000 0000
PD-01
Master : 11C2 2000 0000 0868
Request
request value of address
Response
Word 1 (PKE)
11C2
Word 1 (PKE)
11C2
Word 2 (IND)
2000
Word 2 (IND)
2000
Word 3 (PWE1)
0000
Word 3 (PWE1)
0000
Word 4 (PWE2)
0000
Word 4 (PWE2)
0868
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
17
PD-01 PROFIBUS-DP Module
Example 3: Write data 2 to parameter P0804
To write data to P0804, request ID is set to 2 (Modify parameter value - word), Para
Page Select should be set because the parameter address is greater than 2000. The
address of P0804 is 0x0804, which is 2052 in decimal, if set Page Select to 1 (bit 15
of IND is 1), then the Basic PNU is 2052 – 1*2000 = 052 (0x34), thus, the data
sequence are as follows:
Master
PD-01 : 2034800000000002
PD-01
Master : 1034800000000002
Request
write data to P0804
Response
Word 1 (PKE)
2034
Word 1 (PKE)
1034
Word 2 (IND)
8000
Word 2 (IND)
8000
Word 3 (PWE1)
0000
Word 3 (PWE1)
0000
Word 4 (PWE2)
0002
Word 4 (PWE2)
0002
All parameters values in VFD series Drives are 16-bit, so the data may be transferred
in PWE2 (4th word).
NOTE:
VFD series Drives will write the data to EEPROM. When using PKW to change the
value of parameter, the data will be written to EEPROM directly. However, if this
action is too often, the EEPROM will have no capability of directly saving data.
So please pay close attention on it.
Example 4: Read diagnostic data
User can use the special address to read the current diagnostic data. Please refer to
Section 6.2 for details. The diagnostic address starts from 0x7500 to 0x7504 (5
words). To read diagnostic data in these addresses, request ID is set to 1, Para Page
Select should be set because the parameter address is greater than 2000. The
address 0x7500, which is 29952 in decimal, if set Page Select to 14, then the Basic
PNU is 29952-14*2000=1952(0x7A0), thus, the data sequence are as follows:
Master - > PD-01 : 17A0700000000000
PD-01 - > Master : 17A0700000000300
18
read data from 0x7500
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Request
Word 1 (PKE)
Word 2 (IND)
Word 3 (PWE1)
Word 4 (PWE2)
Response
Word 1 (PKE)
Word 2 (IND)
Word 3 (PWE1)
Word 4 (PWE2)
17A0
7000
0000
0000
17A0
7000
0000
0300
If PD-01 returns the data 0x0300, it indicates that Scan port is disconnected. Please
refer to Section 6.2 for details.
Example 5: Access error
If take any action using PKW to access parameter in AC Drives and it fails, PD-01 will
response error information. Suppose that Master send data sequence is 202D 8000
0000 0002, if VFD series Drives does not find this address (0x07FD), it will respond
the data sequence 702D 8000 0000 0000, response ID is 7 which means cannot
process request (with error number), and error number is 0 (Illegal Parameter
Number).
Request
Response
Word 1 (PKE)
202D
Word 1 (PKE)
702D
Word 2 (IND)
8000
Word 2 (IND)
8000
Word 3 (PWE1)
0000
Word 3 (PWE1)
0000
Word 4 (PWE2)
0002
Word 4 (PWE2)
0000
Response time about PD-01
The update time via PROFIBUS connection can be divided in 3 parts:
T1: Communication time in transmit data from the master to PD-01, and
T2: Wait processing in data buffer of PD-01, and
T3: Communication time in transmit data from PD-01 to VFD Drives.
T1
PD-01
Master
Timer
Data Buffer
T2
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
19
T3
VFD
series
Drives
PD-01 PROFIBUS-DP Module
T1 depends on the actual transmission speed and the type of master in use.
T2 depends on the internal timer of PD-01. Data is transmitted to VFD series Drives per
70ms triggered by a timer. User cannot change the time-out interval.
T3 depends on the Modbus communication between PD-01 and VFD series Drives.
So the update time is,
Max update time = T1 + T2 (70ms) + T3
In fact, the actual update time is less than the Max update time. If the timer time-out
when the data arrive PD-01, PD-01 will save the data to data buffer, and transmit the data
to VFD series Drives immediately.
20
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Chapter 5 User Parameters Setting in GSD file
GSD file
A GSD file is a text file used to identify PROFIBUS-DP device (Master or Slave), which
contains the necessary data for the configuration of DP slaves within a standard DP master.
Typical information in a GSD file are Vendor information, Baud rates supported, Timing
information, Options/features supported and Available I/O signals. The GSD file is the
fundamental building block for the master parameter record.
GSD-File for Delta VFD series Drives
File: DELT08DB.GSD
File start: ===========================================================
#Profibus_DP
; Unit-Definition-List:
GSD_Revision
Vendor_Name
Model_Name
Revision
Ident_Number
Protocol_Ident
Station_Type
FMS_supp
Hardware_Release
Software_Release
Redundancy
Repeater_Ctrl_Sig
24V_Pins
Implementation_Type
Bitmap_Device
Bitmap_Diag
Bitmap_SF
Slave_Family
=1
= "Delta Electronics"
= "VFD DRIVES"
= "Rev. 1"
= 0x08DB
=0
=0
=0
= "V1.0"
= "V1.0"
=0
=2
=0
= "SPC3"
= "VFDDRV"
= "VFDDRV"
= "VFDDRV"
= 1@TdF@Delta VFD Drives
Auto_Baud_supp
=1
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
21
PD-01 PROFIBUS-DP Module
9.6_supp
19.2_supp
93.75_supp
187.5_supp
500_supp
1.5M_supp
3M_supp
6M_supp
12M_supp
MaxTsdr_9.6
MaxTsdr_19.2
MaxTsdr_93.75
MaxTsdr_187.5
MaxTsdr_500
MaxTsdr_1.5M
MaxTsdr_3M
MaxTsdr_6M
MaxTsdr_12M
=1
=1
=1
=1
=1
=1
=1
=1
=1
= 60
= 60
= 60
= 60
= 100
= 150
= 250
= 450
= 800
Freeze_Mode_supp
Sync_Mode_supp
Set_Slave_Add_supp
Min_Slave_Intervall
=1
=1
=0
=1
Modular_Station
Max_Module
Max_Input_Len
Max_Output_Len
Max_Data_Len
Modul_Offset
Fail_Safe
Max_Diag_Data_Len
ORDERNUMBER
=1
=1
= 32
= 32
= 64
=0
=0
= 16
= "PD-01"
Max_User_Prm_Data_Len = 26
User_Prm_Data_Len
= 26
User_Prm_Data
= 0x20,0x00,\
22
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
0x20,0x01,\
0x00,0x00,\
0x00,0x00,\
0x21,0x01,\
0x21,0x02,\
0x21,0x03,\
0x21,0x04,\
0x00,0x01,\
0x00,0x02,\
0x00,0x02,\
0x00,0x01,\
0x00,0x00
Module = "4 PKW, 2 PZD (PPO 1)
EndModule
Module = "0 PKW, 2 PZD (PPO 3)
EndModule
Module = "4 PKW, 4 PZD
EndModule
Module = "0 PKW, 4 PZD
EndModule
" 0xF3, 0xF1
" 0x00, 0xF1
" 0xF3, 0xF3
" 0x00, 0xF3
PrmText = 1
Text(0) = "Address discontinuous"
Text(1) = "Address continue"
EndPrmText
PrmText = 2
Text(0) = "Ignore and Continue"
Text(1) = "Stop accord to Pr.STOP METHOD"
EndPrmText
PrmText = 3
Text(0) = "Stop DataExchange & Report Fault"
Text(1) = "Continue & Report Alarm"
Text(2) = "Ignore & Continue DataExchange"
EndPrmText
ExtUserPrmData = 1 "Data Input 1(PD-01 -> VFD)"
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
23
PD-01 PROFIBUS-DP Module
Unsigned16 0x2000 0-65535
EndExtUserPrmData
ExtUserPrmData = 2 "Data Input 2"
Unsigned16 0x2001 0-65535
EndExtUserPrmData
ExtUserPrmData = 3 "Data Input 3"
Unsigned16 0x0000 0-65535
EndExtUserPrmData
ExtUserPrmData = 4 "Data Input 4"
Unsigned16 0x0000 0-65535
EndExtUserPrmData
ExtUserPrmData = 5 "Data Output 1(VFD -> PD-01)"
Unsigned16 0x2101 0-65535
EndExtUserPrmData
ExtUserPrmData = 6 "Data Output 2"
Unsigned16 0x2102 0-65535
EndExtUserPrmData
ExtUserPrmData = 7 "Data Output 3"
Unsigned16 0x2103 0-65535
EndExtUserPrmData
ExtUserPrmData = 8 "Data Output 4"
Unsigned16 0x2104 0-65535
EndExtUserPrmData
ExtUserPrmData = 9 "d_state"
Unsigned16 1 0-1
Prm_Text_Ref = 1
EndExtUserPrmData
ExtUserPrmData = 10 "din_len"
Unsigned16 2 0-4
EndExtUserPrmData
ExtUserPrmData = 11 "dout_len"
Unsigned16 2 0-4
EndExtUserPrmData
ExtUserPrmData = 12 "LossDPComTreat"
Unsigned16 1 0-1
Prm_Text_Ref = 2
EndExtUserPrmData
24
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
ExtUserPrmData = 13 "LossSPComTreat"
Unsigned16 0 0-2
Prm_Text_Ref = 3
EndExtUserPrmData
Ext_User_Prm_Data_Ref(0) = 1
Ext_User_Prm_Data_Ref(2) = 2
Ext_User_Prm_Data_Ref(4) = 3
Ext_User_Prm_Data_Ref(6) = 4
Ext_User_Prm_Data_Ref(8) = 5
Ext_User_Prm_Data_Ref(10) = 6
Ext_User_Prm_Data_Ref(12) = 7
Ext_User_Prm_Data_Ref(14) = 8
Ext_User_Prm_Data_Ref(16) = 9
Ext_User_Prm_Data_Ref(18) = 10
Ext_User_Prm_Data_Ref(20) = 11
Ext_User_Prm_Data_Ref(22) = 12
Ext_User_Prm_Data_Ref(24) = 13
File END: ==========================================================
NOTE:
The required GSD file is available and can be downloaded from the DELTA web site
http://www.delta.com.tw, or you can copy this text to a text editor such as NOTEPAD, and
save it as a GSD file named “DELT08DB.GSD”. Please make sure to specify the file name
extension as “.GSD”, PLEASE DO NOT SAVE IT extension “.GSD.TXT”.
User parameters in GSD file
The user parameters in GSD file are used for the configuration of the PROFIBUS network.
The description of the user parameters are shown in the following table:
Item
Name
1 Data Input 1
2
Data Input 2
Type
Description
UINT This is a MODBUS address. The 1st word in
PZD of cyclic output data will be sent to this
address.
UINT This is a MODBUS address. The 2nd word in
PZD of cyclic output data will be sent to this
address.
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
25
Default
0x2000
0x2001
PD-01 PROFIBUS-DP Module
Item
Name
3 Data Input 3
4
Data Input 4
5
Data Output 1
6
Data Output 2
7
Data Output 3
8
Data Output 4
9
d_state
10
din_len
11
dout_len
12
LossDPComTreat
Type
Description
UINT This is a MODBUS address. The 3rd word in
PZD of cyclic output data will be sent to this
address if select Module = "4 PKW, 4 PZD".
UINT This is a MODBUS address. The 4th word in
PZD of cyclic output data will be sent to this
address if select Module = "4 PKW, 4 PZD".
UINT This is a MODBUS address. PD-01 will
monitor this address, and copy the return
data to the 1st word in PZD of cyclic input
data.
UINT This is a MODBUS address. PD-01 will
monitor this address, and copy the return
data to the 2nd word in PZD of cyclic input
data.
UINT This is a MODBUS address. PD-01 will
monitor this address, and copy the return
data to the 3rd word in PZD of cyclic input
data if select Module = "4 PKW, 4 PZD".
UINT This is a MODBUS address. PD-01 will
monitor this address, and copy the return
data to the 4th word in PZD of cyclic input
data if select Module = "4 PKW, 4 PZD".
UINT This is a flag. If address in Data Output 1 ~
Data Output 4 is continuous, set it to 1, and
set the others to 0.
UINT This is a length, and unit is word. It specifies
the length of PD-01 to process data in PZD, if
user select the Module = "4 PKW, 4 PZD", but
din_len is 3, PD-01 will process 3 word and
ignore the 4th word.
UINT This is a length, and unit is word. It specifies
the length of PD-01 to monitor data from AC
Drive, if user select Module = "4 PKW, 4
PZD", but dout_len is 3, PD-01 will monitor 3
word and ignore the 4th address.
UINT This variable indicates that the PD-01 will
take action when communication with
Profibus network is lost, the value can be
assigned as follows:
00 – Ignore event and continue;
01 – Stop according to Pr “Stop Method” in
VFD series Drives.
26
Default
0x0000
0x0000
0x2101
0x2102
0x2103
0x2104
0x0001
0x0002
0x0002
0x0001
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Item
Name
13 LossSPComTreat
Type
Description
UINT This variable indicates that the PD-01 will
take action when the SP communication
(SCANport communication) is lost, the value
can be assigned as follows:
00 – Stop data exchange and report fault;
01 – Continue data exchange and report
alarm;
02 – Ignore and continue data exchange.
Default
0x0000
If the address in Data Output 1 ~ Data Output 4 is continuous, then set d_state to 1, PD-01
will get starting address from Data Output 1. The next data will be got from the address next
to the starting address, and the reading length is determined by dout_len. If the MODBUS
address for reading is discontinuous, please set d_state to 0, PD-01 will also get starting
address from Data Output 1, but the difference is the other data will be got from the address
saved in Data Output 2, Data Output 3 and Data Output 4 in order.
Example, if
Data Output 1
= 0x2100;
Data Output 2
= 0x2101;
Data Output 3
= 0x2102;
Data Output 4
= 0x2103;
dout_len
= 0x0003;
The MODBUS address in Data Output 1~Data Output 4 is continuous, so you can set the
d_state to 1, then PD-01 will monitor the address starting from Data Output 1, and monitor 3
words from VFD series Drives one time. When the dout_len is 3, PD-01 will ignore the
address in Data Output 4. If d_state is set to 0, PD-01 will read data from the address in Data
Output 1, and read data from the address in Data Output 2, and so forth.
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
27
PD-01 PROFIBUS-DP Module
Edit the user parameters in S7 Step hardware configuration tools shown below:
NOTE:
Please do not set d_state to 1 when the address in Data Output 1 ~ Data Output 4 is
non-continuous to avoid Parameterization error and IO disconnect. The PD-01 just check the
address starting from Data Output 1 to Data Output [dout_len-1], in other words, if the
address in Data Output 1 ~ Data Output 3 is continuous, but the address in Data Output 4 is
not, and dout_len is 0x0003, then the check still can pass.
28
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Chapter 6 Troubleshooting
Troubleshooting via LED displays
Two LEDs, SP and NET LED, are used to monitor the PD-01 communication status.
Possible LED displays of NET LED:
LED
OFF
Red, flickering (rapid
blinking)
Red, blinking
Red ON
Green, blinking
Green ON
Indication
No Power Supply
Corrective Actions
Verify that the power supply of PD-01.
Check whether the power supply is
connected and that power is applied to
the PD-01 through the connector.
Invalid PROFIBUS address Check whether the switch value is
set via switch
valid, valid value of slave is within
1-125. Set the valid value and re-power
Communication link to
User parameter are sent by master
PROFIBUS, but No cyclical (from GSD file), for example, if d_state
data exchanged, or
is set 1, ensure the data in Data Output
Extended user parameter
1 ~ Data Output 1 + dout_len are
error
continuous addresses. Otherwise,
PD-01 will not be able to pass the
Parameterization check.
No connection to
1. Verify that network installation is OK.
PROFIBUS
2. Verify that PLC is working.
3. Verify that switch address setting is
correct.
“Master” is in “Stop” mode, Turn the KEY of PLC to RUN mode,
and cyclical process data
and send the control command to
exchange in progress, but PD-01.
set-points invalid (control
word = 0)
Cyclic data exchange in
progress and OK
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
29
PD-01 PROFIBUS-DP Module
Possible LED displays of SP LED:
LED
OFF
Indication
No Power Supply
Red, blinking
CRC check fault
Red ON
Connection failure, or
No connection
Green, blinking
Green ON
Corrective Actions
Verify that the power supply of PD-01.
Check whether the power supply is
connected and that power is applied to
the PD-01 through the connector.
Check your communication setting in
AC Drive (9600, <8,N,2>, RTU)
1. Check whether the connections
between AC Drive and RS485 of
PD-01 are all correct
2. Re-wire the connections between AC
Drive and ensure that the wire
specification is correct.
AC Drive returns error code 1. Check the AC Drive type and version.
Not all Delta VFD series Drive are
supported.
2. Check the PLC program, and ensure
the operating address in PD-01 is
correct.
Normal
NOTE:
If both SP LED and NET LED are in steady orange, it indicates that PD-01 has entered into
the “test mode”. Please do not set the value of address switch of PD-01 to 0XFF at this time.
Be sure to set other value and energize PD-01 again.
Troubleshooting via diagnostic data
PD-01 provides 16 bytes diagnostic data when the alarm occurs and when user parameter
setting “LossSPComTreat” is set to “Continue data exchange and report alarm”. It includes 6
bytes standard diagnostic data and 10 bytes device related diagnostic data. The following
table shows the meanings of the 16 bytes:
Byte 1-6
Byte 7
Byte 8
Byte 9
Standard
diagnostic data
Length in bytes
SP communication
status
Error code
Byte 10
Byte 16
Reserved
Byte 7 indicates the length of device related diagnostic data including itself, so if byte 7 is 10
(0Ahex), it indicate device related to diagnostic data have 10 bytes (including byte 7).
Byte 8 indicates the SP communication status when the alarm occurs, and the valid value
should be as follows:
30
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
00 – Normal
01 – CRC check failure
02 – VFD series Drive returns error code
03 – Communication is time out and disconnected
Byte 9 indicates the error code when byte 8 is 02 (VFD series Drive returns error code). Refer
to the Section 6.3 for the meanings of invalid code.
Other word, user can get the diagnostic data via PZD area any time. PD-01 provides some
special MODBUS addresses to indicate the diagnostic status, the address assignments are
as following:
0x7500
0x7501
0x7502
0x7503
0x7504
Address
High
Low
High Low High Low High Low High Low
byte
byte
byte byte byte byte byte byte byte byte
SP
Error
Meaning comm
Reserved, read to 0
code
status
User can get these data through “Data Output 1”, or 2, or 3, or 4 in user parameters. For
example, if set the “Data Output 1” to 0x7500 means get the diagnostic data from 0x7500,
and get the return data from address 0x7500 in 1st word of PZD area.
NOTE:
These special addresses are read-only, it will fail if user tries to write data to it.
Troubleshooting via error codes
If there is a communication error detected between PD-01 and VFD series Drives, the error
code will be displayed on the digital keypad of VFD series Drives.
VFD series Drives can process the message from PD-01 if the communication setting is valid.
But if the command of message is invalid, the VFD series Drives will respond a report
message that has error codes listed in table below, to PD-01.
Code
Meaning
01 Illegal command code
The command code received in the
command message is not available
for the drives.
02 Illegal data address
The data address received in the
command message is not available
for the drives.
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
Corrective actives
1. Check the Request Identifier in PKW area.
PD-01 just supports ID 0, 1, 2.
2. Re-supply power to PD-01.
1. Check the Parameter number in PKW area,
and refer the user manual of VFD Drives.
2. Check the settings of user parameters “Data
Input 1” to “Data Input 4” and “Data Output
1” to “Data Output 4”, and refer to the user
manual of VFD series Drives.
3. Re-supply power to PD-01.
31
PD-01 PROFIBUS-DP Module
Code
Meaning
03 Illegal data value
The data value received in the
command message is not
available for the drives.
Corrective actives
1. Check the parameter data (PWE2) in PKW
area, and refer the user manual of VFD series
Drives.
2. Check the PLC program to confirm the data
that transmitted to PD-01 from master is valid.
3. Re-supply power to PD-01.
04
Slave device failure
1. Check all data in PKW.
The drive is unable to perform the
2. Re-supply power to PD-01.
requested action.
VFD series Drives will not respond message to PD-01 if it receives an invalid message from
PD-01, but error code shown in the table below will be displayed on the digital keypad.
Code
05
06
07
08
09
10
11
12
13
14
Meaning
Corrective actives
Reserved
AC Drive is busy
Reserved
Reserved
1. Please refer to section 4.2 in this manual
Check sum is error
and check the setting of VFD series Drives.
Time out
2. If the error still exists, return it to factory.
Baud rate or protocol is invalid
Message is too short
Message is too long
Message contain invalid character
32
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
PD-01 PROFIBUS-DP Module
Chapter 7 Dimensions
PD-01
SP
NET
A1
B1
A2
ADDH
B2
ADDL
RS-485
DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
33
Download PDF