Aastra | DT422 | User guide | Aastra DT422 User guide

DT412/DT422/DT432
Cordless Telephones for Aastra MX-ONE™ and Aastra MD110
User Guide
Cover Page Graphic
Place the graphic directly on the page, do not care about
putting it in the text flow. Select Graphics > Properties
and make the following settings:
•
Width: 15,4 cm (Important!)
•
Height: 11,2 cm (May be smaller)
•
Top: 5,3 cm (Important!)
•
Left: -0,3 cm (Important!)
This text should then be hidden.
1553-EN/LZT 103 67 D
© Aastra Telecom Sweden AB 2010. All rights reserved.
Table of Contents
Table of Contents
Welcome ......................................................... 4
Important User Information ............................. 6
Description .................................................... 11
Switching On/Off ........................................... 29
Free Seating .................................................. 31
Incoming Calls ............................................... 32
Outgoing Calls ............................................... 37
Phonebook .................................................... 51
During Calls ................................................... 58
Call Forwarding ............................................. 64
Absence Information ..................................... 78
Messages ...................................................... 81
Group Features ............................................. 92
Other Useful Features ................................... 94
Alarm ............................................................. 98
Modes ......................................................... 101
Services ...................................................... 103
Settings ....................................................... 106
Audible Adjustments ................................... 119
Installation ................................................... 123
Reference .................................................... 130
Troubleshooting .......................................... 134
Glossary ...................................................... 136
Index ........................................................... 137
DT412/DT422/DT432
3
Welcome
Welcome
Welcome to the User Guide for the Aastra DT412, DT422 and
DT432 cordless phones. This guide describes the available
features of the telephones when they are connected to Aastra
MD110 or Aastra MX-ONE™.
The functions and features available with these telephones are
designed for easy use in all different telephone handling
situations.
Depending on the version and configuration of the exchange that
your telephone is connected to, some of the functions and
features that are described in this user guide may not be
available. There may also be some differences in the way your
telephone is programmed. Please consult your system
administrator if you need further information.
Some markets use differing codes for some features. In this
guide they are described using the most common code.
The latest version of the user guide can be downloaded from:
http://www.aastra.com
4
DT412/DT422/DT432
Welcome
Copyright
All rights reserved. No parts of this publication may be
reproduced, stored in retrieval systems, or transmitted in any
form or by any means, electronic, mechanical, photocopying,
recording or otherwise, without prior written permission of the
publisher except in accordance with the following terms.
If this publication is made available on Aastra´s homepage, Aastra
gives its consent to downloading and printing copies of the content
provided in this file only for private use and not for redistribution. No
parts of this publication may be subject to alteration, modification or
commercial use. Aastra will not be liable for any damages arising
from use of an illegal modified or altered publication.
Warranty
AASTRA MAKES NO WARRANTY OF ANY KIND WITH
REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. Aastra shall not be
liable for errors contained herein nor for incidental or
consequential damages in connection with the furnishing,
performance or use of this material.
Declaration of Conformity
Hereby, Aastra Telecom Sweden AB, Box 42214,
SE-126 17 Stockholm, declares that this telephone is in
conformity with the essential requirements and other relevant
provisions of the R&TTE directive 1999/5/EC.
Details to be found at: http://www.aastra.com/sdoc
DT412/DT422/DT432
5
Important User Information
Important User Information
Safety instructions
Save these instructions.
Read these safety instructions before use!
Recommendations
•
•
•
•
•
•
•
6
Always keep and handle your products with care
and keep them in a clean and dust-free place.
Proper use and care will prolong the products
life. Use a soft absorbent tissue or cloth to
remove dust, dirt or moisture.
Always ensure that the phone, battery and
charger are used and operated in the
environment for which they are designed.
Operate the phone in temperatures between
0°C to +40°C (32°F to 104°F).
Do not expose your products to
liquid, moisture, humidity, solvents,
strong sunlight, harsh environments
or extreme temperatures, never
above +60°C (+140°F), unless the
product has been specifically
designed and officially approved for such
environments.
Exposure to heat may cause
batteries to leak, overheat or
explode, resulting in fire, burns or
other injuries.
Do not put the product in the
microwave oven: This may cause damage to
either the oven or the product.
Do not attempt to disassemble or
alter any part of the phone, the
charger(s) or the battery-pack.
Disassembly or alteration may result
in electrical shock or irreversible
damage to the equipment. Only a
qualified service personnel or an authorized
Aastra partner should conduct internal
inspections, alterations and repairs.
•
•
•
•
•
Do not expose your product to open flames or lit
tobacco products.
Do not drop, throw or bend your products. This
may cause malfunction or electric shock.
Do not paint your product.
Do not use your product in an area where a
potentially explosive atmosphere exists, unless
the product has been specifically designed and
officially approved for such environments.
To avoid hearing impairment, accept the call
before holding your product (or portable
handsfree device) to your ear.
Disposal of the product
•
Your product should not be placed in
municipal waste. Please check local
regulations for disposal of electronic
products.
DT412/DT422/DT432
Important User Information
Power supply
•
•
•
•
•
•
•
•
•
Connect the AC power adapter of the charging
unit only to the designated power sources as
marked on the charger.
Make sure the cord is positioned so that it will
not be subjected to damage or stress.
To reduce risk of electrical shock, unplug the
chargers from any power source before
attempting to clean or move it.
The AC power adapters must not be used
outdoors or in damp areas.
Never modify the cord or plug. If the plug will not
fit into the outlet, have a proper outlet installed
by a qualified electrician.
Limit the distance between the mains socket and
the cordless phone when charging for easy
accessibility.
As an energy saving measure, disconnect the
charger from the main socket after charging.
When unplugging the mains adapter from the
power outlet, make sure that your hands are dry
and ensure that you hold the solid portion of the
mains adapter.
Do not pull on cables.
•
•
•
•
•
•
•
•
•
•
•
Charging and batteries
Please read carefully the following
important precautions before the first
time use of the batteries. Make sure
to understand and observe all
cautionary instructions stated, so as
to avoid any possible safety hazards
that are caused by any misuse, misapplication
or damage to batteries.
•
Only use batteries, mains adapters or desk and
rack chargers which have been specifically
designed for use with your product.
•
Use of power sources not explicitly
recommended may lead to overheating,
reduced battery performance, distortion of the
equipment and fire or other damages.
•
Cordless phones are equipped with Nickel Metal
Hydride (NiMH) batteries or Lithium Ion Lion
batteries. In a complex infrastructure, the talkand standby time may differ, due to the
consequence of the increase in signaling.
•
The battery must always be completely charged
(minimal 4 hours) before first time use.
•
The battery in your product is designed to
withstand many charge cycles.
•
Use only the recommended charging
equipment.
•
Improper charging can cause heat damage or
even high pressure rupture.
•
Observe proper charging polarity.
DT412/DT422/DT432
•
•
•
•
•
•
Do not solder lead wires directly onto the battery.
Do not allow water to come into contact with the
battery.
The initial charging of a NiMH battery will cause
the battery to become warm. This is a normal
effect of charging NiMH batteries.
The batteries are replaceable, however it is not
the intention to do this frequently.
Only charge the batteries when placed in the
phone.
Use only the specified battery-packs for your
product.
Never heat or dispose of the battery into a fire,
which, or else, may cause leakage, burst or fire.
Remove the carrying case from the product
while in charger.
Do not cover the product while being charged.
Do not charge the phone in a closed cabinet or
drawer. The charging of the battery is a chemical
process and causes the battery to become
warm during charging. Make sure the
environment in which the phone is charged, is
well vented.
The cordless phone can be charged either when
switched on or off.
Do not connect the battery's positive and
negative leads altogether in any circumstances.
Do not strike or drop the battery. It may cause
damage to the battery.
Do not charge the battery below
+5°C (+41°F). Be sure to charge the
battery between +5°C and +45°C
(+41°F and 113°F). Charging beyond
these conditions may impair the
battery performance and shorten the
life cycle.
Do not use battery packs from different types,
brands or of different capacities.
The battery is to be stored in a dry cool place,
with the ambient temperature of approx. +25°C
(+77°F) for best performance.
The battery continues to discharge a minimal
portion of its power, even if the product is
switched off or the battery is removed.
Dispose the battery in accordance with all local
regulations, applicable in your country.
7
Important User Information
Warnings
Preventing malfunction
Smoke or fumes
•
Stop operating the products and
turn off immediately in case of
smoke or fumes. Unplug the mains
adapter and remove the batteries from the
phone immediately. Continued operation may
result in fire or electrical shock.
LCD
•
If the liquid crystal display breaks, avoid injury by
not allowing the liquid crystal to come into
contact with eyes, skin or mouth. Prevent the
liquid crystal from leaking out of the broken
glass.
•
•
•
•
8
Never place the equipment in close proximity of
electric motors, welding equipment or other
devices generating strong (electro) magnetic
fields. Exposure to strong (electro) magnetic
fields may cause malfunction and corrupt the
communication.
Moving the equipment rapidly between warm
and cold temperatures may cause condensation
(water droplets) to form on its internal and
external surfaces. Water droplets may cause
malfunction of the equipment and corrupt or end
communication or damage the equipment.
When condensation is noticed, stop using the
equipment. Switch off the phone, remove the
battery and unplug the mains adapter from the
power outlet. Wait until the moisture evaporates
from the equipment before putting it in operation
again.
Avoid accidental drop of the phone. Use the clip,
security clip or carrying case specified for
carrying purposes of the phone.
Avoid squeezing the phone between furniture
and your body when carrying the phone in your
pocket or attached to clothing.
DT412/DT422/DT432
Important User Information
SIM card
Your phone has a removable SIM card (Subscriber Identity
Module) to store your settings. This means that you can move
your SIM card from one phone to another and keep all your
settings.
Safety information
The DT412, DT422 and DT432 phones are IP64 classified, which
means that they are robust, dust- and waterproof, designed for
people working in tough environments.
Intrinsic safety (DT432)
The DT432 phone is approved according to the ATEX directive to
be used in potentially explosive gas and dust environments.
Compliance with the Essential Health and Safety Requirements,
with the exception of those listed in the schedule to this
certificate, has been assured by compliance with the following
documents:
EN 50014:1997 plus amendments A1 and A2
EN 50020:2002
IEC 61241-0:2004 plus Corrigendum 1
IEC 61241-11:2005
IEC 60529:1989
The classification and marking on the product is “II 2G EEx ib IIC
T4” for gas and “II 3D Ex ibD 22 IP64 T50°C” for dust.
DT412/DT422/DT432
9
Important User Information
Preparing for use
Before using your phone for the first time you have to charge and
connect the battery, see section “Installation” on page 123.
Note: Place the phone in the charger and charge it for at
least one hour before using it the first time.
Cleaning
Clean the phone only with a soft, water dampened cloth. Using
soap or any other cleaning materials may discolor or damage the
phone. Clean the battery contacts using ethanol or isopropyl
alcohol.
10
DT412/DT422/DT432
Description
Description
1
12
14
11
12
2
10
3
4
5
7
6
8
9
13
1
DT412/DT422/DT432
Lamp
A flashing lamp indicates an incoming call or a message waiting.
11
Description
2
Volume Up/Down
Off-hook: raise/lower speaker volume, see section “Audible
Adjustments” on page 119. The Volume Up key can also be used
to answer calls, see section “Answer calls” on page 32.
3
Display
The display can for example show the battery status, time,
system, owner ID/name, extension number and the Soft key
information. See sections “Display information” on page 14 and
“Menu structure” on page 22. It is possible to change the text size
in the display, see section “Settings” on page 106.
4
Soft keys
The functions depend on the traffic state and will be shown on the
last line of the display. When you are requested to (see display),
press the required key to access the function. Used for different
choices in the menu structure (menu mode). In idle mode the
functions of the Soft keys can be changed by you. The middle
Soft key is also used to turn Loudspeaking on or off. See sections
“Settings” on page 106, “Display information” on page 14 and
“Menu structure” on page 22.
5
Call key
Switch on. Make call, answer call, end call.
6
Navigation key
Controls the movement of the cursor in the display. In idle mode,
the Navigation key (down) is used for entering the Call list and
the Navigation key (up) is used for entering the message list.
Pressing Navigation key (left) will show the current date in the
display window. When navigating the menu structure, the key is
used for moving up, down, back (left), or next (right).
7
Menu key
Enter/exit the menu mode, see sections “Display information” on
page 14 and “Menu structure” on page 22. Also used to manually
lock/unlock the keypad, see section “Lock the keypad” on
page 115.
8
Keypad
Enter numbers and writing texts, see section “Enter names and
numbers” on page 52. Keys 0-9 can be programmed as Hot
keys, see section “Hot keys and Soft keys” on page 107.
9
Microphone
10
12
Mute key
Turn off/on audible signals in idle mode, silencing the ring signal
at an incoming call, and also to turn the microphone on/off during
a call.
DT412/DT422/DT432
Description
11
Alarm key (DT422 and DT432 only)
Sending alarms and testing the Alarm function. See section
“Alarm” on page 98.
12
Loudspeakers
One loudspeaker for ring signal and one for Loudspeaking. See
section “Handsfree” on page 58.
Please note: The phone may retain small magnetic
articles around the earpiece region.
DT412/DT422/DT432
13
Charging connector
See section “Installation” on page 123.
14
Headset connector
See section “Headset” on page 132.
13
Description
Display information
The display gives you visual feedback on all actions that you
perform, and also textual warnings. In idle mode the upper row is
used for icons and the clock. The next three rows are information
rows (20 possible characters in each row), showing system
information, names and numbers that you edit or dial, your owner
ID etc. The third information row is used for showing the status of
the phone (current mode). Examples of status information are;
Muted, In charger etc. When there is no status to show, the row
is empty.
Note: It is possible to change the owner ID and the text
size in the display, see section “Settings” on page 106.
The lower row displays the Soft key field. In idle mode it shows
the user defined names of the three Soft keys beneath the
display. In menu mode where the Soft keys are used for different
choices, it gives you the function of each Soft key. Examples of
functions are; Back, Option, Save etc. How to define the Soft keys
in idle mode, see section “Hot keys and Soft keys” on page 107.
Note: The information displayed varies depending on the
version and configuration of the exchange, and whether
you use a DECT or an IP DECT phone. Consult your
system administrator to find out which type of phone you
have.
The display:
3
5
System A
S Evans 2174
Info
14
Doctor
13:05
Jobs
DT412/DT422/DT432
Description
The following display examples show the different states of your
phone:
Note: If a name is available it is displayed instead of or
together with the number.
Idle phone
Depending on the state and setting of your phone, different
information can be shown.
Normal:
System A
Smith 4321
13:05
“System A” is the default name of your network. On the second
row is your name (if available) and extension number.
Note: If the name is long, the number is not displayed.
Follow-me activated:
4321 >
4444
13:05
The display shows your own extension number 4321 diverted to
extension number 4444.
DT412/DT422/DT432
15
Description
Outgoing call
Normal outgoing call:
When you make an outgoing call both the traffic state and the
dialed number or name are displayed:
13:05
Calling
3333
R
When the outgoing call is answered:
13:05
3333
R
Diverted call:
If the dialed number is diverted, the diversion information is
shown. For example, the display shows the dialed number 3333
(Smith) diverted to 4444 (Brown):
13:05
4444
>3333
R
When the diverted call is answered, only the number of the
answering position is displayed:
13:05
4444
R
16
DT412/DT422/DT432
Description
Incoming call
Normal incoming call:
If available, the number or the name of the caller is displayed.
13:05
3333
Diverted call:
A diversion indicator before the number or name informs that the
call is diverted to your phone. For example, the display shows
that number 3333 (Smith) was dialed, but the call was diverted to
you:
4321
>3333
13:05
When you have answered the call, the display shows only the
caller's number.
DT412/DT422/DT432
17
Description
System connection messages
System A
No system
System indication
The phone is in contact with System A. It is also possible for the
system to be named something else, e.g. MD110.
Out of coverage
The phone is not in contact with any system. Please ask your
system administrator to log on the phone.
Note: When re-entering the coverage area it can take a
couple of minutes before the phone automatically has
registered into the system.
It is also possible to get an out of coverage warning signal,
contact your system administrator if you require this.
No access
Access indication
Your phone has contact with a system, calling is not allowed.
Display icons
Call / Off-hook
Appears when your phone is off-hook and flashes during ringing.
Audio signal off
Shown when all alert signals, including ring signal, message
tone, key beep etc. are turned off. High priority messages will
however override this setting. See section “Audible Adjustments”
on page 119.
Battery
Always shown in the display in idle mode. When the level is low it
is time to charge the battery. See section “Installation” on
page 123.
Loudspeaking (handsfree)
Shown when the loudspeaker is activated and the phone is in
Loudspeaking operation (handsfree). See section “During Calls”
on page 58.
3
18
New message
Appears when a new message is received. The number on the
right side of the icon shows the total number of unread
messages. The symbol will remain until the message is marked
as read. See section “Messages” on page 81.
DT412/DT422/DT432
Description
Note: For voice messages the New message icon is only
an indication of received voice messages, the number
does not reflect the actual number of unread messages.
5
Not answered call
Added to not answered calls in the Call list. The number on the
right side of the icon shows the total number of missed calls.
Key
Indicates that your keypad is locked. See section “Automatic key
lock” on page 115.
Padlock
Indicates that the phone has been locked, and has to be
unlocked with a code before it can be used. See section “Phone
lock” on page 112.
Headset
Indicates that a headset is connected to the phone. See section
“Headset” on page 132.
No-movement Alarm on (DT422 and DT432 only)
Indicates that the No-movement Alarm is activated. See section
“Alarm” on page 98.
Man-down Alarm on (DT422 and DT432 only)
Indicates that the Man-down Alarm is activated. See section
“Alarm” on page 98.
ABC
Upper case text input
Indicates that you can type upper case letters and numbers in
text input mode. See section “Enter names and numbers” on
page 52.
abc
Lower case text input
Indicates that you can type lower case letters and numbers in text
input mode. See section “Enter names and numbers” on
page 52.
123
Number input
Indicates that you can type numbers in text input mode. See
section “Enter names and numbers” on page 52.
Incoming call
Added in front of incoming calls in the Call list.
Outgoing call
Added in front of outgoing calls in the Call list.
DT412/DT422/DT432
19
Description
Unread message
Added in front of not read messages in the message list. See
section “Messages” on page 81.
Read message
Added in front of read messages in the message list. See section
“Messages” on page 81.
Interactive message
Added in front of an incoming interactive message in the
message list. See section “Messages” on page 81.
Read interactive message
Added in front of read interactive messages in the message list.
See section “Messages” on page 81.
Add contact
Appears on a Soft key when a phone number is marked in the
Call list. It indicates that it is possible to add the phone number to
the local Phonebook. See section “Phonebook” on page 51.
Contacts
Displayed when it is possible to get a phone number from the
local Phonebook, for example to add it to a function. See section
“Phonebook” on page 51.
>
20
Diversion indicator
When displayed before a name or number it indicates that the
phone is diverted to another extension.
DT412/DT422/DT432
Description
Menu tabs
The following tabs are displayed when you press the Menu key:
Messages
Here you can find the message list. See section “Messages” on
page 81.
Contacts
Here you can find the local Phonebook, the central Phonebook
and the Call list. See sections “Phonebook” on page 51 and “Dial
number from the Call list” on page 41.
Modes
Here you can select between modes, and change or edit modes.
See section “Modes” on page 101.
Services
Here you can select, add, delete, or change a Service function.
See section “Services” on page 103.
Settings
Here you can handle your phone settings. See section “Settings”
on page 106.
To navigate the menus, see section “Menu structure” on page 22.
Additional display features
Depending on which network you are connected to, additional
display features are available. Ask your system administrator if
you require additional display features.
DT412/DT422/DT432
21
Description
Menu structure
ç
The available phone and network functions can be accessed via
the menus.
Press the Menu key to enter or exit the menus.
The last used tab is marked, or if the phone has been restarted,
the menu tab Contacts.
Use the Navigation key (left/right) to choose tab and press the
Navigation key (down) to open it; a heading is shown and the first
alternative is marked. Use the Navigation key (up/down) to step
in the alternatives and select one by pressing Navigation key
(right).
Notes:
Since the phone can be used in several networks, some
functions might not be supported in your network.
A parameter setting in the SIM card determines if changes
that are made from the menu is saved on the SIM card. If
changes are not saved on the SIM card, they will be
discarded when the phone is restarted.
22
DT412/DT422/DT432
Description
Messages tab
Messages list >
Message 1 >
Message 2 >
.
.
Message 20 >
Message 1 (time/date)
SMS tab
Send SMS >
SMS Address >
SMS
Contacts tab
Local phonebook >
Central phonebook
Call list >
DT412/DT422/DT432
Entry 1 >
Entry 2 >
.
.
Entry 100 >
Name: .....
Number: .....
Call number 1
Call number 2
.
.
.
.
.
Call number 20
23
Description
Modes tab
Normal >
In charger >
Mode 2 >
Mode 3 >
Mode 4 >
Mode 5 >
Mode 6 >
Mode 7 >
Mode 8 >
Mode 9 >
Volume >
(Level 1,2..5, Silent)
Ring signals >
Vibrator (on/off)
Key beep (on/off)
Internal call: >
External call: >
Callback: >
Alarm settings* >
No-movement (on/off)
Man down (on/off)
Beep,
Low,
Medium,
High,
Mixed
Absent (on/off)
Switch off
Ordinary
Auto
Loud
Auto loud
Answer >
Soft key**
Name: ...
* Only available for the DT422 and DT432
** See section “Settings tab” on page 25 for more information.
Services tab
Service 1 >
Service 2 >
.
.
Service 10 >
24
Name: ....
Function:
Data send
Data with prefix
Phone call
SMS
DT412/DT422/DT432
Description
Settings tab
Alert signals >
Volume: >
(Level 1,2..5, Silent)
Internal call: >
External call: >
Callback: >
Ring signals >
Vibrator (on/off)
Key beep (on/off)
Alarm settings*> No-movement (on/off)
Man down (on/off)
Hot key >
0, 1, 2.....9 >
Data send
Data with prefix
Phone call
Short-cut >
SMS
Change mode
Not used
General >
Language >
(English, etc)
Text size** >
Small
Medium
Phone lock >
Lock phone
Set lock code
Clock (on/off) >
Auto key lock (on/off)
Quick answer (on/off)
New message rotated (on/off)
Owner ID
Display contrast
Auto setting
Manual setting
Soft key >
System >
Left: >
Middle: >
Right: >
Name: ....
Function: >
Beep,
Low,
Medium,
High,
Mixed
Absent
Local phonebook
Central phonebook
Services
Switch off
No-movement*
Man-down*
Edit alarm data*
Change system
Demo Mess 1
Demo Mess 2
RSSI
* Only available for the
DT422 and DT432
phones.
** Only available for the
DT412 and DT422
phones.
Select system >
Auto, System A.....D
Register >
System A.....D
Location test* >
Activate test
Information >
IPDI / IPEI / SW version / AP SW version
DT412/DT422/DT432
25
Description
Customizing the menus
Your system administrator can customize the menus by hiding
some of the functions that are available. Which functions that
should be hidden are decided with settings in the SIM card. The
following functions can be hidden:
26
•
Deletion of messages - The options Delete and Delete all
are hidden.
•
Administration of local Phonebook - It is not possible to
add new entries, or edit and delete existing entries.
•
Editing modes - The settings for the modes cannot be
altered.
•
Changing modes - The option Select is hidden, i.e. it is not
possible to change modes from the menu.
•
Switch off handset - It is not possible to switch off the phone
from the Modes menu.
•
Administration of services - It is not possible to add new
services, or edit and delete existing services.
•
Changing alert signals - The Alert signals alternative in
the menu is hidden.
•
Changing alarm settings - The Alarm settings alternative
in the menu is hidden.
•
Administration of Soft keys - The Soft key alternative in the
menu is hidden.
•
Administration of Hot keys - The Hot key alternative in the
menu is hidden.
•
Edit of Hot keys - The option Edit is hidden. It is possible to
see the settings for the Hot keys.
•
Changing general settings - The General settings
alternative in the menu is hidden.
•
Handling Phone Lock - The Phone lock alternative in the
menu is hidden.
DT412/DT422/DT432
Description
•
Changing system* - The Select system alternative in the
menu is hidden.
•
Register system* - The Register alternative in the menu is
hidden.
•
Delete system - The option Delete is hidden.
•
View information* - The Information alternative in the menu
is hidden.
•
Location test* - The Location Test alternative in the menu is
hidden.
•
Central Phonebook address - When an address to the
central Phonebook is specified, the alternative Central
Phonebook will appear in the Contacts menu and the short-cuts
list. At delivery the address is set to 999999.
* If all these alternatives are hidden, the System alternative in the
menu will be hidden.
Each mode in the menu can be hidden individually. This makes it
possible to remove modes that are not used from the menu. Note
that it is still possible to change to the hidden modes with help of
Soft and Hot keys.
DT412/DT422/DT432
27
Description
Tones
The following different tones are sent from the exchange to your
phone.
Tone characteristics
The tones shown in this section are the most used tones
worldwide. Many markets use a differing tone for one or more
situations.
Dial tone
Special dial tone
Ringing tone or queue tone
Busy tone
Congestion tone
Number unobtainable tone
Call waiting tone
Intrusion tone
Conference tone
every 15 seconds (to all parties)
Verification tone
Warning tone, expensive route
Ring signals
You can change the ring signals, see section “Ring signals” on
page 121.
28
DT412/DT422/DT432
Switching On/Off
Switching On/Off
æ
Switch on
Press and hold until the display lights up.
If the phone does not switch on or the Battery icon is displayed,
the battery is low. Charge the battery.
The display shows:
Switch on?
No
Yes
Yes
Press within two seconds to confirm (see display).
Now you can use your phone.
Notes:
If the message No System is displayed you cannot make
or answer calls.
Depending on system programming, your phone can be
locked. To unlock the phone, see section “Phone lock” on
page 112.
DT412/DT422/DT432
29
Switching On/Off
Switch off
Notes:
During calls, you cannot switch off your phone.
It is recommended that you program the Switch off
function as a Hot key, see section “Hot keys and Soft
keys” on page 107. If you do not program a Hot key, you
can use the menus, see section “Modes” on page 101.
å
ã Yes Ok
30
If you have programmed a Hot key:
Press and hold the Hot key.
Press to confirm (see display).
Now your phone is switched off.
DT412/DT422/DT432
Free Seating
Free Seating
The Free Seating function is used for persons who have an office
extension number but no telephone set of their own. For
example, flexible office workers, persons mostly outside the
office, etc. As a free seating user and working from the office, you
logon to any free telephone set that temporarily will be assigned
with your extension number and your system authorities.
Note: Free seating is not supported by IP DECT.
*11*
å*
å#æ
æ
#11# æ
æ
DT412/DT422/DT432
To log on
Dial.
Enter the Authorization Code and press.
Enter your phone number and press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
The display shows your phone number.
To log off
Dial and press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
31
Incoming Calls
Incoming Calls
A ring signal and the flashing red lamp indicate an incoming call.
The ring type can tell you whether the call is an internal, external
or callback call and the display indicates an incoming call.
The twenty last received/dialed phone numbers are stored in the
Call list, see section “Dial number from the Call list” on page 41.
Answer calls
The caller’s number and the Call icon is displayed:
13:05
4736
æ
Press to answer.
Note: Calls can be answered at any time, no matter if you
are programming, or keying in a number etc.
The Volume Up key can also be used to answer calls
(handsfree speaking mode activated).
When a headset is connected to the phone, the button on
the headset can be used to answer the call.
32
DT412/DT422/DT432
Incoming Calls
Mute ring signal
If the phone rings at an inconvenient moment:
æ
ä
Press the Mute key on the right side of the phone to suppress
the ringing.
All alert signals, including the vibrator, will silence for this specific
call. See section “Description” on page 11 for the location of the
Mute key.
Press to answer the call.
Handsfree
Press the middle Soft key to answer the call in handsfree
speaking mode.
You are connected to the caller via the loudspeaker and
microphone.
Note: Which key to press depends on the answering
method used, to change the answering method see
section “Change answering method” on page 34.
æ
End the call
Press.
The duration time of the call is shown.
Note: When a headset is connected to the phone, the
button on the headset can be used to end the call.
On another extension
åæ
8
You can answer a call to a phone in another room:
Call the ringing extension and press.
Busy tone.
Press
4
Note: France press ; Sweden press
DT412/DT422/DT432
6
33
Incoming Calls
Change answering method
You can choose; Ordinary, Auto, Loud, or Auto loud.
ç
à á
ã
á
ãá
ã
or
Select
34
•
Ordinary; press the middle Soft key and the call is connected
with Loudspeaking function turned on.
•
Auto; the call is automatically connected (call is not connected
with Loudspeaking function).
•
Loud; press the Call key and the call is connected with
Loudspeaking function turned on.
•
Auto loud; the call is automatically connected with
Loudspeaking function turned on after 2 signals (Calls can be
answered as usual before that).
Press.
The last used tab is marked.
Select Modes.
Press to enter Modes.
Select Normal.
Select Answer.
Select the required answering method.
Press (see display).
The name of the selected method is shown. The new answering
method is selected.
DT412/DT422/DT432
Incoming Calls
Parallel Ringing
The Parallel Ringing function makes it possible for an incoming
call to ring several phones simultaneously and for the call to be
answered on any of the phones. The main advantage of this
function is that you do not risk losing any calls.
The function requires all the phones involved to be defined in a
Parallel Ringing list, which must be configured and initiated by
your system administrator. Because only calls to a main
extension will be distributed among the phones in the list, this
main extension also needs to be defined.
A call to a specific extension will not be distributed to other
phones in the list, and will only ring that specific extension's
phone.
Parallell Ringing can be temporarily disabled by the phone user
using the function “Internal Follow-me”. See also section “Internal
Follow-me” on page 64.
*21* å #
æ
æ
To disable Parallel Ringing temporarily
Dial, enter the extension number and press.
Note: U.K., dial
* 2 * Number #.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
If you want to disable Parallel Ringing for all phones defined in
the list, follow the procedure for disabling the function from the
phone with the main extension number and enter the number of
the answering position.
If you want to disable Parallel Ringing for one specific phone in
the list only, follow the procedure for disabling the function from
this phone and enter its extension number.
DT412/DT422/DT432
35
Incoming Calls
#21#
æ
æ
To restore Parallel Ringing
Dial.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Notes:
U.K., dial
# 2 #.
If you want to restore Parallel Ringing for all phones
defined in the list, follow the procedure for restoring the
function from the phone with the main extension number
and enter the number of the answering position.
If you want to restore Parallel Ringing for one specific
phone in the list only, follow the procedure for restoring
the function from this phone and enter its extension
number.
36
DT412/DT422/DT432
Outgoing Calls
Outgoing Calls
Make calls
You can also make a call via the Phonebook, see section
“Phonebook” on page 51.
åæ
On-hook
Enter the phone number and press.
The number is shown in the display. Your phone will go off-hook
and establish the connection. The number is stored in the Call
list.
The number may be any of the following:
DT412/DT422/DT432
•
an extension number,
•
an external number, where 0 is the digit for external call
access.
37
Outgoing Calls
Notes:
Correct a wrong entry by pressing C (see display). If you
decide not to make the call while keying in the number,
press C (see display) to stop.
It is possible to turn on/off the tone sender in a predialed
number by making a long press on the * key (e.g. when
calling telephone banks). Tone sender on will be indicated
with a T in the number, and off with -. If a pause is required
in the number, it is added by making a long press on the
# key. The pause is indicated with a P in the number.
You can make your calls faster by programming Soft/Hot
keys with frequently used numbers. See section “Program
a Hot key or a Soft key with a phone number” on
page 109.
If you receive a queue tone when the digit or digits to get
an external line are dialed (if the feature Least Cost
Routing is used in the system), keep waiting. Once a line
becomes free you will receive a dial tone. If a warning
tone is heard, the selected line is marked “Expensive”.
Off-hook dialing
æ
å
If you prefer to dial a number off-hook:
Press.
Dial tone.
Key your number on-line.
Notes:
When dialing this way, you cannot press C (see display) to
erase digits.
The number is not stored in the Call list.
Off-hook dialing is not supported by IP DECT.
Handsfree
ä
38
While you are waiting for a connection, dial tone or during the
call:
Press the middle Soft key.
You are connected to the caller via the loudspeaker and
microphone.
DT412/DT422/DT432
Outgoing Calls
Note: Which key to press depends on the answering
method used, to change the answering method see
section “Change answering method” on page 34.
æ
DT412/DT422/DT432
End the call
Press.
The duration of the call is displayed.
39
Outgoing Calls
Number Presentation Restriction
If you do not want your name and number to be displayed to the
person you are calling, use the following procedure.
Notes:
This function might be blocked for use on your extension
(programmed by your system administrator).
*42# æ
å
The Number Presentation Restriction is only valid for the
ongoing call, i.e. the procedure has to be repeated the
next time you want to use it.
Dial and wait for a new dial tone.
Dial the number.
Instead of your name and number, the display on the called
phone shows Anonymous.
Last External Number Redial
*** æ
When you initiate an external call the system automatically stores
all the dialed digits, irrespective of whether the call was
successful or not.
Press to redial the last dialed external number.
The display will show the dialed number.
Note: Finland and Sweden, dial
40
**0
DT412/DT422/DT432
Outgoing Calls
Dial number from the Call list
The twenty last received/dialed phone numbers are stored in the
Call list. You can dial one of these numbers by selecting the
number from the Call list.
ã
If the Clock and Date function is set, you can on the same day
the call was received/dialed, see the time for the call. The time
stamp is changed to a date stamp the following day. See section
“Clock settings” on page 113.
Press until the desired number is displayed.
You can store numbers permanently by adding them to your
Phonebook, see section “Save a number from the Call list to the
Phonebook” on page 55.
If you want to edit the number:
Edit
å
æ
Press (see display).
Make the required changes.
Press to dial.
The display will show the dialed number.
Note: The Call list is cleared when your phone is switched
off or the power of your phone is lost.
DT412/DT422/DT432
41
Outgoing Calls
Delete a number from the Call list
ã
Options
Select
When your phone is in idle mode:
Press until the desired number is displayed.
Press (see display).
Delete is marked.
Press (see display).
Number deleted is displayed and the number is deleted.
Delete all numbers from the Call list
ã
Options
ã
Select
When your phone is in idle mode:
Press to enter the Call list.
The first number in the Call list is marked.
Press (see display).
Delete is marked.
Select Delete all.
Press (see display).
The display shows:
Delete all numbers?
No
Yes
42
Yes
Press (see display).
All numbers are deleted.
DT412/DT422/DT432
Outgoing Calls
When you receive a busy tone
If you call an extension and receive a busy tone, or get no
answer, or all external lines are busy, you can use any of the
following methods:
Callback
6
If a called extension is busy or there is no answer:
æ
Note: France, Finland and Sweden, press
æ
Press.
5
Press to finish the procedure.
You are called back (recall ring signal) when the ongoing call is
finished or the next time a new call is finished. You have to
answer within eight seconds, otherwise the Callback service is
cancelled. While waiting for the Callback, you can make and
receive calls as usual.
Press when you are called back.
The system calls the extension.
Note: Callbacks can be activated on several extensions
at the same time.
DT412/DT422/DT432
43
Outgoing Calls
6#
If all external lines are busy when the Hook key is pressed after
dialing the external number (on-hook dialing):
Press.
Notes:
If you were dialing off-hook (the Hook key was pressed
before the number), you are required to add the external
number now.
æ
æ
France, Finland and Sweden, press
5#
Press to finish the procedure.
When an external line becomes free you will be called back
(recall ring signal). You have to answer within eight seconds,
otherwise the Callback service is cancelled. While waiting for the
Callback, you can make and receive calls as usual.
Press when you are called back.
The system calls the external number.
Note: Only one Callback can be activated on a busy
external line.
#37* å
#æ
æ
44
Cancel any single Callback
Dial and enter the extension number.
Note: To cancel a single Callback on a specific external
line, dial the digit or digits to get a line instead of the
extension number.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
DT412/DT422/DT432
Outgoing Calls
#37#
æ
æ
Cancel all Callbacks
Dial.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Activate Call Waiting
5
If you urgently wish to contact a busy extension or external line,
you can notify by a Call Waiting signal.
Press
6
4
Note: France and Finland, press ; Sweden, press .
Keep your phone off-hook
When the called extension or the external line becomes free, it
will be called automatically.
Note: The Call Waiting function might be blocked for use
on your extension (programmed by your system
administrator). If Call Waiting is not allowed, you will
continue to receive a busy tone.
Intrusion on a busy extension
4
You can intrude on an ongoing call on a busy extension.
Press
8
Note: France and Sweden, press .
Before the Intrusion is executed a warning tone is sent to the
parties in the ongoing call. A three party call is established and a
warning tone is heard.
Note: The warning tone might be disabled for your
system. The Intrusion function might be blocked for use
on your extension (programmed by your system
administrator). If Intrusion is not allowed, you will continue
to receive a busy tone.
DT412/DT422/DT432
45
Outgoing Calls
Bypass
æ
*60* å
#
46
If this function is allowed from your extension, you can bypass
an; activated Diversion, activated Follow-me or activated
Absence Information on a specific extension.
Press.
Dial and enter the extension number.
Press and wait for answer.
DT412/DT422/DT432
Outgoing Calls
Speed Dialing
Note: You can also make Speed Dialing calls via the
Phonebook and Call list, see sections “Phonebook” on
page 51 and “Dial number from the Call list” on page 41.
Common Speed Dialing numbers
å
æ
By using common Speed Dialing numbers, you can make calls
simply by pressing a few keys. The common Speed Dialing
numbers consist of 1–5 digits and are stored in the exchange (by
your system administrator).
Dial the common Speed Dialing number.
Please refer to your telephone directory.
Press to make the call.
Dial a number via Hot key or Soft key
The Hot key or Soft key has to be preprogrammed with a number,
see section “Hot keys and Soft keys” on page 107.
å
Via Hot key:
ä
Via Soft key:
DT412/DT422/DT432
Press and hold the preprogrammed Hot key.
A number between 0 and 9. The display shows the
preprogrammed number. The number is dialed and the
connection will be established automatically.
Press the preprogrammed Soft key (see display).
The display shows the preprogrammed number. The number is
dialed and the connection will be established automatically.
47
Outgoing Calls
Authority
Authorization Code, common
If you are assigned to use a common Authorization Code (1 to 7
digits) you can temporarily change any used phone within the
exchange to the authority level connected to this code. You can
use the code for one call only or you can open the phone for
some calls and lock it when leaving the phone.
48
*72*
å#æ
å
To use for a single call:
#73*
å#æ
æ
To open an extension for some calls:
*73*
å#æ
æ
To lock an extension
Dial.
Enter Authorization Code and press.
Verification tone.
Dial the digit or digits to get an external line and the external
number.
Dial.
Enter Authorization Code and press.
Verification tone.
Press to finish the procedure.
Dial.
Enter Authorization Code and press.
Verification tone.
Press to finish the procedure.
DT412/DT422/DT432
Outgoing Calls
Authorization Code, individual
If you are assigned to an individual Authorization Code (1 to 7
digits, assigned to your own extension) you can lock your own
extension to a common authority level, e.g. when out of the
office. You can also temporarily change any other used phone
within the exchange to the same authority level as you have on
your own phone. The individual code can be changed from your
own extension.
*76*
å#æ
æ
*75*
å#æ
å
#76*
å#æ
æ
DT412/DT422/DT432
To lock your phone:
Dial.
Enter Authorization Code and press.
Verification tone.
Press to finish the procedure.
To make calls with your authority level when your phone is
locked:
Dial.
Enter Authorization Code and press.
Verification tone.
Dial the digit or digits to get an external line and the external
number.
To open your phone:
Dial.
Enter Authorization Code and press.
Verification tone.
Press to finish the procedure.
49
Outgoing Calls
50
*75*
å*
å#æ
å
To assign your own authority level to another phone:
*74*
å*
å#æ
æ
To change your individual Authorization Code:
Dial.
Enter Authorization Code and press.
Dial your own extension number and press.
Verification tone.
Dial the digit or digits to get an external line and the external
number.
Dial.
Enter old Authorization Code and press.
Dial new Authorization Code and press.
Verification tone.
Press to finish the procedure.
DT412/DT422/DT432
Phonebook
Phonebook
Your phone is equipped with a local Phonebook (personal) and a
central Phonebook.
In the local Phonebook you can make up to 100 entries (names
and numbers). The Phonebook entries are stored on the SIM
card in your phone.
Notes:
Phonebook numbers have a maximum of 22 digits and
phone book names have a maximum of 16 characters.
An indication that the Phonebook is full (indicated with a
beep), means that you have to delete an entry before you
can add a new one.
You can also open the Phonebook by programming a
Soft/Hot key. See section “Hot keys and Soft keys” on
page 107.
DT412/DT422/DT432
51
Phonebook
Enter names and numbers
The characters that you can enter, are written above each key.
Use the keypad to write text. The following explains how to write
text when you add a new name in the Phonebook menu.
Example (to write SMITH):
7777
6
444
8
44
ã
The marked character is selected after a time out or when
another key is pressed.
Press for S
Press for M
Press for I
Press for T
Press for H
Press when the name is complete.
Control keys
à
á
*
0
C
While entering a name or a number you can use the following
keys for control and navigation:
Press to move left.
Press to move right.
Press to switch between upper and lower case.
Note: It is possible to turn on/off the tone sender in a
predialed number by making a long press on the * key
(e.g. when calling telephone banks). Tone sender on will
be indicated with a T in the number, and off with -.
Press to enter a space.
Press to correct a wrong entry (see display).
Note: Deletes the entire entry if held longer.
52
DT412/DT422/DT432
Phonebook
Special characters
Use the keypad to enter letters and characters. Press a key once
for the first letter or character, twice for the second, three times
for the third, etc. The most common letters are printed above
each key on the phone. All the available letters and characters
are shown in the following table:
Number of times to press the key
Phone
key
1
2
3
4
5
6
7
8
9
10
11
1
-
?
!
,
.
:
"
’
(
)
1
Â
Ã
Ç
Ô
Õ
6
µ
\
¿
±
¦
2
A
B
C
Å
Ä
Æ
À
Á
3
D
E
F
È
É
Ê
Ë
3
4
G
H
I
ï
Ì
Î
Í
4
5
J
K
L
5
6
M
N
O
Ñ
Ö
Ø
Ò
Ó
7
P
Q
R
S
ß
7
8
T
U
V
Ü
Ù
Ú
Û
8
9
W
X
Y
Z
Ý
9
0
Space
+
&
<
@
=
/
>
$
^
%
_
£
°
#
12
13
2
½
0
§
Note: Depending on the selected menu language, other
characters might be available, which means that the
character order differs from the table above.
2
DT412/DT422/DT432
Example special characters:
To enter Ä press 2 (five times).
1 time
result A
2 times result B
3 times result C
4 times result Å
5 times result Ä
53
Phonebook
Enter the Phonebook
ç
à á
ã
á
or
Access the names and numbers of the Phonebook.
Press.
The last used tab is marked.
Select Contacts.
Press to enter Contacts.
Select Local phonebook.
The name list is shown.
Local phonebook
Adam
>
Bob
Charlie
Add
Delete
Find
Make a call via the Phonebook
When you have accessed the central or local Phonebook:
Find
å
Ok
â ã
æ
or
54
Press (see display).
Find:_ is displayed.
Press the key which has the first letter of the name you are
looking for.
How to write text, see section “Enter names and numbers” on
page 52.
Press to confirm (see display).
The first name beginning with that letter is displayed.
Scroll up or down until you find the name.
Press.
The number is dialed.
DT412/DT422/DT432
Phonebook
Add a name and a number to the
Phonebook
When you have accessed the Phonebook:
Add
Press (see display).
Name: _
Number:
å
C
ã
å Save
ç
à á
ã
á
â ã
or
or
å Save
DT412/DT422/DT432
Back
ABC
C
Save
Enter the name.
How to write text, see section “Enter names and numbers” on
page 52.
Press to correct a wrong entry (see display).
Press.
Enter the phone number and press (see display).
The name and number are stored in the Phonebook.
Save a number from the Call list to the
Phonebook
Press.
The last used tab is marked.
Select Contacts.
Press to enter Contacts.
Select Call list.
Scroll up or down the Call list until you find the number.
Press.
The number is automatically added to the Phonebook.
Enter the name and press (see display).
How to write text, see section “Enter names and numbers” on
page 52. The name and number are stored in the Phonebook.
55
Phonebook
Change a name and a number in the
Phonebook
â ã
á
or
When you have accessed the Phonebook:
Scroll up or down until you find the name.
Select the name.
Name: Adam
Number: 001811005555
Back
Edit
å
C
ã
å Save
56
Delete
Edit
Press (see display).
Edit the name.
How to write text, see section “Enter names and numbers” on
page 52.
Press to correct a wrong entry (see display).
Press.
Edit the phone number and press (see display).
The name and number are changed.
DT412/DT422/DT432
Phonebook
Delete a name and a number from the
Phonebook
â ã
á
or
Delete
When you have accessed the Phonebook:
Scroll up or down until you find the name.
Select the name.
The name and number is displayed.
Press (see display).
Delete entry?
No
Yes
DT412/DT422/DT432
Yes
Press to delete the name and number (see display).
The name and number are deleted.
57
During Calls
During Calls
Handsfree
This function is useful in situations when you need to have a
conversation over the phone while having your hands free for
other tasks (handsfree). You can switch to handsfree speaking
(and back to standard speaking procedure) at any time during a
call.
ä
ä
58
To activate handsfree during a call:
Press the middle Soft key to activate handsfree speaking
mode.
You are connected to the caller via the loudspeaker and
microphone.
Note: You can adjust the volume, see section “Audible
Adjustments” on page 119.
Press again to deactivate handsfree speaking mode.
DT412/DT422/DT432
During Calls
Mute microphone
To mute the microphone during an ongoing conversation:
Press the Mute key at the right side of the phone to turn the
microphone off.
The microphone is disconnected and the caller will not hear an
ongoing conversation or environmental noises. The text Muted is
shown in the display when the microphone is off during a call.
Press the Mute key again to turn the microphone on.
Note: It is advised to use this feature instead of putting a
call on hold. A call on hold may be diverted to your
operator, directly or after some time.
Inquiry
You have an ongoing conversation and you would like to make
an Inquiry to an internal or external party.
R
å
R
ææ
2
Press (see display).
Dial tone. The first call is put on hold.
Call the third party.
When the third party answers, you can switch between the calls
(Refer Back), transfer the call, create a Conference and end one
of the calls.
Press to end the Inquiry call (see display).
The third party is disconnected.
Press to return to the first party.
Refer Back
Press to Refer Back to the other party.
The party you talked to is put on hold, the other party is
connected.
Note: Sweden press R (see display).
DT412/DT422/DT432
59
During Calls
Transfer
You have an ongoing call and you want to transfer the call to
another extension.
R
å
æ
Press (see display).
Dial tone.
Call the third party.
Press before or after answer
The ongoing call is transferred.
Note: If you have put more than one call on hold the last
call that was put on hold will be transferred. If the dialed
extension is busy or Transfer is not allowed, your phone
will ring again.
Call Waiting
If you hear the Call Waiting tone during an ongoing conversation,
another person is trying to contact you.
æ
æ
To terminate the ongoing call and answer the waiting call:
Press to finish the ongoing call.
The waiting call is signalled on your phone.
Press to answer the new call.
Note: The Call Waiting function might be blocked for use
on your extension (programmed by your system
administrator).
60
DT412/DT422/DT432
During Calls
Conference
With this procedure you can include up to seven parties in a
conference. Only the conference leader (i.e. the person initiating
the conference) can admit participants. During the conference a
tone will be heard every 15 seconds.
Note: The conference tone might be disabled for your
system.
You have an ongoing conversation and want to establish a
telephone conference. You will become the conference leader.
R
å
3
æ
Press (see display).
Dial tone.
Call the third party.
Wait for answer.
Press to establish a conference.
Repeat the procedure to add more conference members.
End the call to leave the conference.
Note: A tone burst is heard each time a participant enters
or leaves the conference. When the conference leader
leaves the conference, the conference will continue with
the other included parties. The conversation is changed
back to a normal two party connection when there is only
two parties left.
Answer a conference call
æ
A conference call is indicated by a different signal compared to
normal calls and a text message. The conference call must be
answered within a pre-set time (default 30 seconds). A normal
call in progress has higher priority, but if the normal call is ended
before the pre-set time, the conference call indication starts and
the call can be answered.
Press to answer the conference call.
You are connected to the conference.
Note: Conference call is not supported by IP DECT.
DT412/DT422/DT432
61
During Calls
On hold
You can temporarily put the ongoing call on hold. Calls put on
hold can be resumed on your own or on another phone.
R
æ
æ
åæ
8
Press (see display).
Dial tone.
Press.
To resume the call on your extension
Press within 30 seconds.
If not resumed within 30 seconds you will be called back. An
unanswered external call will be re-routed to the operator after
another 30 seconds.
To resume on another extension
Call the extension where the call was put on hold and press.
Busy tone.
Press.
4
6
Note: France, press ; Sweden, press .
Dialing during a connected call
When calling interactive teleservices, e.g. telephone banks, you
need to use Dual Tone Multi Frequency (DTMF) signals. If your
exchange is not already programmed to automatically convert
your entered digits into DTMF signals, you need to activate the
function during the call.
9å
During an ongoing call:
Press and dial the required digits.
Entered digits are transferred as DTMF signals.
Note: Finland press
62
1 and dial the required digits.
DT412/DT422/DT432
During Calls
Push-to-talk button
There are two different types of push-to-talk functions that are set
by SIM card parameters in the phone. For both variants the Mute
key has to be pressed during conversation.
The first push-to-talk function can be described as a group call/
conference call. To enter the group call the members must press
a Soft/Hot key with a pre-programmed dial-code. If one of the
group members wants to get in contact with the others, he/she
simply presses and holds the Mute key to open the microphone.
The microphone is muted again when the Mute key is released.
The dial-code is set in the Soft/Hot key as a phone number, see
section “Hot keys and Soft keys” on page 107.
Note: When this function is enabled all calls started with
a Soft/Hot key will be using the push-to-talk function.
The second push-to-talk function is used in systems where only
one person is allowed to speak (not two persons at the same
time). The phone sends DTMF tones to the connected system
when the Mute key is pressed/released to open/close the speech
channel.
DT412/DT422/DT432
63
Call Forwarding
Call Forwarding
Internal Follow-me
All calls to your extension are diverted to an extension of your
choice (within the private network). During Follow-me the display
shows a > after your number. On the next row the answering
position number is shown. A special dial tone will be heard.
During Follow-me, your phone can still be used for outgoing calls.
*21* å
#æ
æ
Order
Dial and enter the answering position number.
Note: U.K., dial
* 2 * and number.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Display example:
4736 >
4321
64
13:05
DT412/DT422/DT432
Call Forwarding
#21# æ
Cancel
Dial and press.
Note: U.K., dial
æ
#2#
Wait for the call icon to stop flashing.
Press to finish the procedure.
Remote Programming of Follow-me
Using remote programming of Follow-me, you can manage the
Follow-me settings of other extensions besides the extension you
are currently located at. You can, for example, activate Followme for extension 1234 while being located at extension 5678.
*21* å
*å
#æ
æ
#21* å
#æ
Follow the steps below to activate Follow-me for another
extension:
Dial and press the extension number to divert.
Note: U.K.: press
*2*
Dial and press the internal number of the Follow-me position.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Follow the steps below to terminate Follow-me for another
extension:
Dial and press the diverted extension number.
Note: U.K.: press
#2*
Press.
Wait for the call icon to stop flashing.
DT412/DT422/DT432
65
Call Forwarding
æ
Press to finish the procedure.
External Follow-me
If external Follow-me is allowed, you can have all calls to your
extension diverted to an external number of your choice. During
Follow-me the display shows a > after your number. A special dial
tone will be heard. During Follow-me, your phone can still be
used for outgoing calls.
*22#
å
#æ
æ
Order
Dial.
Dial the digit or digits to get a line and enter the external
number.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Display example:
4736 >
#22#
æ
66
13:05
Cancel
Dial.
Press.
DT412/DT422/DT432
Call Forwarding
æ
Wait for the call icon to stop flashing.
Press to finish the procedure.
Remote Programming of External Follow-me
Using remote programming of External follow-me, you can
manage the External follow-me settings of other extensions
besides the extension you are currently located at. You can, for
example, activate External follow-me for extension 1234 while
being located at extension 5678.
*22* å
#å
#æ
æ
#22* å
#æ
æ
DT412/DT422/DT432
Follow the steps below to activate External follow-me for another
extension:
Dial and press the extension number to divert.
Dial and press the external call access digits and the external
number.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Follow the steps below to terminate External follow-me for
another extension:
Dial and press the diverted extension number.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
67
Call Forwarding
Personal Number
With this feature you can be reached on your normal office phone
number even if you are out of the office, at home, etc.
Depending on the functionality of your office exchange, you can
have either one individual single search profile (standard) or you
can choose between five individual search profiles (optional).
A search profile can be designed to fit the situation, i.e. in the
office, traveling, at home, etc. Both internal or external phone
numbers can be used in a profile.
Your search profile is programmed or modified by your system
administrator. See section “To design and order your search
profiles” on page 71.
When the feature is activated, incoming calls are transferred to
your selected phones or back-up services in the order that you
choose. If an answering position in the profile is busy, the call can
be transferred to another predefined position in the profile, i.e.
Voice Mail or a colleague.
You can handle the profiles from your own office phone. How to
do this is described in this section (an operator can also assist
you).
You can also use any of the Personal Assistant applications, if
available. Contact your system administrator for more
information.
When out of the office, the feature Direct Inward System Access
(DISA) can be used, if available in your system. How to use DISA
is described in this section.
68
DT412/DT422/DT432
Call Forwarding
*10*
(1–5)
#æ
æ
To activate or change to another profile from your office
phone
Dial.
Press the search profile digit.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Note: When another party is included in the activated
profile, a colleague or an operator, etc., always remember
to inform about your absence. If Voice Mail is included in
the activated profile, always update your greeting with
Absence Information.
#10#
æ
æ
DT412/DT422/DT432
To cancel from your office phone
Dial.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
69
Call Forwarding
To activate or change to another profile from an external
phone
z
*75*
z*
z#
*10*
z*
(1–5)
#d
#
*
The external phone must be of push button type provided with
pound key ( ) and star key ( ) or a mobile phone adapted for
dial tone pulses (DTMF).
Call the DISA function at your office.
Dial tone.
Dial.
Enter the Authorization Code and press.
Dial your own extension number and press.
Dial tone.
Dial.
Dial your own extension number and press.
Press the search profile digit.
Press and replace the handset.
Note: When another party is included in the activated
profile, a colleague or an operator, etc., always remember
to inform about your absence. If Voice Mail is included in
the activated profile, always update your greeting with
Absence Information.
70
DT412/DT422/DT432
Call Forwarding
To cancel from an external phone
z
*75*
z*
z#
#10*
z#
d
#
*
The external phone must be of push button type provided with
pound key ( ) and star key ( ) or a mobile phone adapted for
dial tone pulses (DTMF).
Call the DISA function at your office.
Dial tone.
Dial.
Dial the Authorization Code and press.
Dial your own extension number and press.
Dial tone.
Dial.
Dial your own extension number and press.
Replace the handset.
To design and order your search profiles
The search profiles are installed or changed by your system
administrator. In order to set up your profiles, copy the setting
form, fill in your new or changed profiles and give it to your
system administrator.
Note: If a profile handling application is connected to your
system, you can edit profiles via your Intranet. See
separate instructions for the application.
DT412/DT422/DT432
71
Call Forwarding
Important notes when designing your search profiles:
•
Avoid ring times longer than 45 seconds for your profiles.
Usually the caller hangs up after 3-6 ring signals. If you need
a longer ring time, the maximum time is 60 sec.
•
Consider the time you need to react and answer on each
answering position in your profile.
You might need up to 15 seconds to react and answer a call
on a desk or cordless phone and 20–25 seconds for a mobile
phone.
•
There must be an answering position at the end of every
profile (Voice Mail or operator/secretary).
If not, calls might end up unanswered.
•
Consider what should happen while you are busy on a phone.
The available options are:
•
–
Follow-me to Voice Mail
–
Follow-me to the operator
If an answering machine, a fax or other answering device is
used as an early answering position, it might interrupt the
searching.
Disconnect the answering device, or design the ring times so
they do not affect the searching.
•
If your system admits just one single personal profile, design
the profile only with your 2–3 most frequently used positions.
If you add more numbers, there is a risk that the caller hangs
up before a latter position is called.
•
If your system admits 1–5 personal profiles, design the
different profiles to fit your most frequently used positions.
Make sure you use as few answering positions as possible for
each profile. Profile examples:
72
–
In office
–
At home
–
Traveling
–
Absent/not reachable
DT412/DT422/DT432
Call Forwarding
Example:
How to fill in your setting form for search profiles:
Profile 1
In office
Search
order
Type of telephone or
Answering position*
Telephone number
Ring time
(seconds)
1
Desk
1234
10
2
Cordless
5234
15
3
Voice Mail
* Examples: Desk, Cordless, Mobile, External, Voice Mail, Operator, etc.
Profile 2
DT412/DT422/DT432
At home
Search
order
Type of telephone or
Answering position*
1
External
222222
20
2
Mobile
0706666666
25
3
Voice Mail
Telephone number
Ring time
(seconds)
73
Call Forwarding
Setting form for search profiles
Name:
Department:
Telephone No:
Account:
Profile 1
..........................
Search
order
Type of telephone or
Answering position*
Telephone number
Ring time
(seconds)
1
2
3
4
* Examples: Desk, Cordless, Mobile, External, Voice Mail, Operator, etc.
Profile 2
..........................
Search
order
Type of telephone or
Answering position*
Telephone number
Ring time
(seconds)
Telephone number
Ring time
(seconds)
Telephone number
Ring time
(seconds)
Telephone number
Ring time
(seconds)
1
2
3
4
Profile 3
..........................
Search
order
Type of telephone or
Answering position*
1
2
3
4
Profile 4
..........................
Search
order
Type of telephone or
Answering position*
1
2
3
4
Profile 5
..........................
Search
order
Type of telephone or
Answering position*
1
2
3
4
74
DT412/DT422/DT432
Call Forwarding
Remote Programming of Diversion
Remote Programming of Direct Diversion
By using Direct diversion, incoming calls are directly forwarded to
a predefined extension. Using remote programming of Direct
diversion, you can manage the Direct diversion settings of other
extensions besides the extension you are currently located at.
You can, for example, activate Direct diversion for extension
1234 while being located at extension 5678.
Follow the steps below to activate Direct diversion for another
extension:
*21*
å*
#æ
æ
#21*
å
#æ
Dial.
Dial the extension number to divert and press.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Follow the steps below to terminate Direct diversion for another
extension:
Dial.
Dial the diverted extension number.
Press.
Wait for the call icon to stop flashing.
DT412/DT422/DT432
75
Call Forwarding
æ
Press to finish the procedure.
Remote Programming of Diversion on No Answer
By using Diversion on no answer, incoming calls are forwarded to
a predefined extension after a number of signals. Using remote
programming of Diversion on no answer, you can manage the
Diversion on no answer settings of other extensions besides the
extension you are currently located at. You can, for example,
activate Diversion on no answer for extension 1234 while being
located at extension 5678.
Follow the steps below to activate Diversion on no answer for
another extension:
*211*
å
#æ
æ
#211*
å
#æ
æ
76
Dial.
Dial the extension number to divert.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Follow the steps below to terminate Diversion on no answer for
another extension:
Dial.
Dial the diverted extension number.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
DT412/DT422/DT432
Call Forwarding
Remote Programming of Diversion on Busy
By using Diversion on busy, incoming calls are forwarded to a
predefined extension when you are busy in a call. Using remote
programming of Diversion on busy, you can manage the
Diversion on busy settings of other extensions besides the
extension you are currently located at. You can, for example,
activate Diversion on busy for extension 1234 while being located
at extension 5678.
*212*
å
#æ
æ
#212*
å
#æ
æ
DT412/DT422/DT432
Follow the steps below to activate Diversion on busy for another
extension:
Dial.
Dial the extension number to divert.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Follow the steps below to terminate Diversion on busy for
another extension:
Dial.
Dial the diverted extension number.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
77
Absence Information
Absence Information
The Absence Information is used to inform callers why you are
absent and when you return. If you are authorized, you can also
enter Absence Information for another extension from your own
extension. A special dial tone will be heard. During Absence
Information, your phone can still be used for outgoing calls.
Order
*23* ( 0 – 9 )
*0915
#æ
æ
Example: Back on September 15 (=0915).
Dial and enter the absence code.
Note: The absence code is system dependent. Contact
your system administrator regarding the available
absence codes.
Press and enter date (MMDD) or time (HHMM) of your return.
Note: If no return time or date is needed, this step can be
skipped.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Display example:
4736 TRIP
15 Sep
13:05
Note: This is not displayed on IP DECT.
78
DT412/DT422/DT432
Absence Information
#23#
æ
æ
*230*
å*
(0–9)
*0915
#æ
Cancel
Dial.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
The programmed information is erased.
Order for another extension
Dial.
Dial the extension number and press.
Enter the absence code.
Press and enter the date (MMDD) or time (HHMM) of the other
person's return.
Note: If no return time or date is needed, this step can be
skipped.
Press.
Wait for the call icon to stop flashing.
æ
DT412/DT422/DT432
When the display on the other person's extension shows the
reason, and if entered, time or date of return:
Press to finish the procedure.
79
Absence Information
#230*
å#æ
Cancel for another extension
Dial.
Dial the extension number and press.
Wait for the call icon to stop flashing.
æ
80
Note: If the special dial tone is received, the Authorization
Code for the other extension is required. Add the code
and press before pressing the Hook key.
#
Press to finish the procedure.
DT412/DT422/DT432
Messages
Messages
When you receive a new message, the flashing lamp,
accompanied by a message tone and/or a vibrating phone, give
you notice of a message (a special dial tone can also be used to
indicate a waiting message, if programmed).
The New message icon is also used to indicate a new message.
In addition you can see the number of queued messages in the
display.
The message tone can be silenced by a press on the Mute key.
Notes:
The message tone will break through silent mode if the
message is urgent.
The message list is cleared when your phone is switched
off or the power of your phone is lost.
DT412/DT422/DT432
81
Messages
Manual Message Waiting (MMW)
If the called extension does not answer you can initiate a
message waiting indication on that extension (if this function is
allowed).
Answer
An indication of a waiting message appears in the display, e.g.
Voice mail: 1.
Listen
Press (see display).
A call is initiated to the extension that requested Message
Waiting.
Note: If the message is not answered within a certain time
(pre-defined by the system administrator), the Message
icon appears in the display, e.g. 3 . The message is
answered via the message list, see section “Text
messages” on page 84.
*31* å
#æ
æ
#31# å
#æ
Order MMW to another extension
Dial and enter the extension number.
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
The message is sent to the called extension.
Cancel MMW to another extension
Dial and enter the extension number.
Press.
Wait for the call icon to stop flashing.
82
DT412/DT422/DT432
Messages
æ
DT412/DT422/DT432
Press to finish the procedure.
83
Messages
Text messages
The twenty last received text messages are stored in the
message list. To send text messages see section “SMS (Short
Message Service)” on page 87.
Notes:
If there is not enough free memory to store an incoming
message the oldest message will be deleted. This means
that it is not always possible to store twenty messages, it
depends on how big the messages are.
â
â ã
á
or
By pressing any key (not Alarm, Mute, and Volume keys)
the received message is marked as read.
Press to enter the message list.
Scroll up or down until you find the message.
The selected message is highlighted.
Press to read the message.
Lunch today?
From: Phil Collins
11:00 15/12
Delete Exit
13:05
If the Clock and Date function is set, you can on the same day
the message was received, see the time for the message. The
time stamp is changed to a date stamp the following day. See
section “Clock settings” on page 113.
The size of the text can be changed or be displayed upside
down, see section “Settings” on page 106.
84
DT412/DT422/DT432
Messages
To delete a message:
Delete
Yes
Press (see display).
Delete message? is shown in the display.
Press to delete the message (see display).
If you get a text message with a request for answer, the text
Acknowledge is added to the message. Use the Soft keys to do a
positive or negative acknowledgement.
Note: The option Delete is not available for a message
with request for answer. An unacknowledged message
can only be deleted from the message list.
To reply to an incoming text message:
å Send
Reply
DT412/DT422/DT432
Press (see display).
Enter the message text and press (see display).
Sending is displayed as a confirmation of the transfer.
85
Messages
Absent
Activate Absent if you cannot receive any SMS messages. The
system will then receive an absent notice, and keeps track of if
you can be reached or not.
This function can be programmed as a Hot key or a Soft key.
How to program a Soft/Hot key, see section “Hot keys and Soft
keys” on page 107. It is also possible to activate/deactivate this
function via the menu, see section “Modes” on page 101.
Notes:
This feature may be restricted or not available. Ask the
system administrator for the availability and for more
information.
If you program a Hot key, you have to press and hold the
key when you activate/deactivate this feature.
Activate
Absent
Press the preprogrammed Soft/Hot key (see display).
The display shows:
Absent
Smith 4321
13:05
Deactivate
Absent
Press preprogrammed Soft/Hot key (see display).
The display shows:
System A
Smith 4321
86
13:05
DT412/DT422/DT432
Messages
SMS (Short Message Service)
SMS messages from one phone to another is enabled by
programming a Soft/Hot key to SMS, see section “Hot keys and
Soft keys” on page 107. If you program the Soft/Hot key without a
destination address you will be able to use it for sending an SMS
to any phone within the system, but you can also choose to send
to a predefined destination address.
An incoming SMS is immediately displayed and the number of
the sending phone is shown on a separate row. The time and
date the SMS was received, and the number of the sending
phone, is shown when you read the message. To view and reply
incoming SMS messages, see section “Text messages” on
page 84. All SMS messages are saved along with other
messages in the message list.
Notes:
This feature may be restricted or not available. Ask the
system administrator for the availability and for more
information.
If you program a Hot key, you have to press and hold the
key when you activate/deactivate this feature.
Send an SMS
SMS
å
Press the preprogrammed Soft/Hot key (see display).
Enter the destination number,
If you are sending an SMS to a predefined destination address,
this step is excluded.
or
press to fetch it from the local Phonebook (see display).
If you are sending an SMS to a predefined destination address,
this step is excluded.
Ok
å Send
DT412/DT422/DT432
Press (see display).
If you are sending an SMS to a predefined destination address,
this step is excluded.
Enter the message text and press (see display).
Sending is displayed as a confirmation of the transfer.
87
Messages
Interactive Messaging
Interactive Messaging (IM) is a function that extends basic
messaging. It makes it possible to access information from a
client application in the system. An example can be a centralized
Phonebook (a central phone number directory) that can be
accessed from your phone, or that a list of actions is included in
the message sent from the application to the phone.
Mobile data from the phone can initiate the application to send
the Interactive Message. The user can then select one action
from the list. The action can be sending a message back to the
application, and/or dialing a specific number etc.
Note: This feature may be restricted or not available.
Ask the system administrator for the availability and for
more information.
Incoming Interactive Message
An Interactive Message is indicated and viewed the same way as
an ordinary message, but the Interactive message icon is added
in front of the message. It is saved along with other messages in
the message list.
If the message gives you several options:
Select
å Ok
Mark the one you want and press (see display).
If the selected option requests input:
Enter the information needed and press (see display).
A press on the middle Soft key will change to digit input mode to
facilitate entering numbers.
Send mobile data
It is possible to send user entered data from the phone by
pressing a preprogrammed Hot key or Soft key, or selecting a
service. Mobile data can be used for opening a door, starting/
stopping a machine etc. The data can either be predefined, or
entered after the Soft/Hot key is pressed or service is selected.
Mobile data with prefix can be used to send information to an
application in the system (can also be predefined when you
program the Soft/Hot key or service). See sections “Hot keys and
Soft keys” on page 107 and “Services” on page 103.
88
DT412/DT422/DT432
Messages
Voice Mail (optional)
The Voice Mail application allows you to leave a voice message
to the caller when you are unable to answer calls, e.g. when out
of office, in a meeting, etc. The caller can then leave a message
in your mailbox. When back in your office you can enter your
mailbox and listen to the messages received.
You can choose to divert all incoming calls to your mailbox, or
calls when there is no answer, or calls when your phone is busy.
If you use the Personal Number feature, it is recommended to
program Voice Mail as the last answering position for all search
profiles.
When you enter your mailbox, you will hear recorded instructions
on how to handle listening, recording, storing and deleting
messages, and how to change your security code.
Note: How to handle your mailbox, depends on the type
of Voice Mail system. The following describes the, in
MD110, integrated type. For other types, please refer to
separate user instructions. Contact your system
administrator if you do not know which type of Voice Mail
system you have.
To activate and deactivate your mailbox
See section “Internal Follow-me” on page 64 (function code 21).
Use the number to the Voice Mail system as the “answering
position number”.
To access your mailbox when there is a new message
Listen
å
DT412/DT422/DT432
Press (see display).
If you are asked to enter your security code:
Enter your security code.
Code at delivery = your extension number.
89
Messages
To access your mailbox in general
åæ
å
åæ
#
å
å
åæ
#
å
å
90
When you want to listen to saved messages, change your
security code or change your greeting.
Dial the number to the Voice Mail system and press.
If you are asked to enter your security code (if the phone you are
using has a mailbox of its own):
Enter your security code.
Code at delivery = your extension number.
To access your mailbox from another phone
Dial the number to the Voice Mail system and press.
If you are asked to enter your security code (if the phone you are
using has a mailbox of its own):
Press.
Dial your mailbox number.
(normally your office extension number)
Enter your security code (if required).
To access someone else’s mailbox
Dial the number to the Voice Mail system and press.
If you are asked to enter your security code (if the phone you are
using has a mailbox of its own):
Press
Dial the mailbox number
(normally the office extension number of the other person).
Enter the security code of the other person (if required).
DT412/DT422/DT432
Messages
To handle the mailbox
Recorded information on the line informs about the number of
new and stored messages. If you have too many messages
stored, you will first be asked to delete saved messages.
Recorded instructions ask you to press different digits in order to
listen to caller's messages, record your own greetings, change
your password or exit your mailbox, etc.
The following diagram gives an overview of the mailbox system
and the digits to be used.
t level
DT412/DT422/DT432
91
Group Features
Group Features
Group Call-pick-up
People working in a team can have their phones programmed by
the system administrator to form Call-pick-up groups.
*8# æ
In a Call-pick-up group, any member can answer any individual
call to group members.
Dial and press to answer.
Notes:
One Call-pick-up group can serve as an alternative to
another group. Calls to the alternative group can only be
answered when there are no calls to your own group.
Finland and Sweden, press
*0#
Common Bell Group
*8# æ
Calls are signalled on a common bell.
Dial and press to answer.
Note: Finland and Sweden, press
92
*0#
DT412/DT422/DT432
Group Features
Group Hunting
An internal Group Hunting number is a common directory number
for a group of extensions. Calls to the group will be indicated at a
free extension in the group.
When you leave the group temporarily, you make your phone
unavailable for incoming calls.
*21* å
#æ
æ
#21# æ
To leave the group temporarily
Dial and enter your own extension number.
Note: U.K., dial
Press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
To re-enter the group
Dial and press.
Note: U.K., dial
æ
DT412/DT422/DT432
* 2 * and number.
#2#
Wait for the call icon to stop flashing.
Press to finish the procedure.
93
Other Useful Features
Other Useful Features
Account Code
*61*
å#æ
å
This function is used to charge a call to an account number or to
prevent unauthorised calls from your phone. The Account Code
can have 1 to 15 digits.
Dial.
Note: Norway and Finland, dial
* 7 1 *.
Dial the Account Code and press.
Dial tone.
Dial the digit or digits to get an external line and the external
number.
Ongoing external call
When the Account Code function is used to charge a call it is also
possible to connect an ongoing external call to an Account Code.
During the call:
R
*61*
å#
R
ææ
94
Press to put the ongoing call on hold (see display).
Dial tone.
Dial.
Note: Norway and Finland press
* 7 1 *.
Enter Account Code and press.
Dial tone.
Press (see display).
Press to resume the call that was put on hold.
DT412/DT422/DT432
Other Useful Features
General Deactivation
The following features can be simultaneously cancelled:
#001# æ
æ
•
Callback (all Callbacks are cancelled).
•
Internal and External Follow-me.
•
Manual Message Waiting/Message Diversion.
Order
Dial and press.
Wait for the call icon to stop flashing.
Press to finish the procedure.
Night Service
When the exchange is in Night Service mode, all your incoming
calls to the operator are transferred to a selected extension or
group of extensions. The exchange is equipped with three
different Night Service modes:
Common Night Service
All incoming calls to the operator are transferred to one specific
extension. Answer the call in the normal way.
Individual Night Service
Selected external calls to the operator are transferred to one
specific extension. Answer the call in the normal way.
Universal Night Service
All incoming calls to the operator are transferred to a universal
signalling device, e.g. the common bell. Answer the call as
descibed in section “Common Bell Group” on page 92.
DT412/DT422/DT432
95
Other Useful Features
Emergency mode
In the event of an emergency, the operator can set the exchange
into Emergency mode, during which only preprogrammed
extensions are permitted to make calls. If your extension is not
assigned with this category and you try to make a call, you will
not receive a dial tone.
Malicious Call Tracing
If you are disturbed by bothersome or malicious external
incoming calls, you can request number tracing from the network
provider.
You can invoke tracing during or after an ongoing conversation.
The external line can be held for a limited period of time.
Order
During an ongoing conversation:
R
*39#
96
Press (see display).
Dial tone.
Dial.
The system acknowledges with different tones whether the
tracing request was accepted or rejected.
DT412/DT422/DT432
Other Useful Features
DISA = Direct Inward System Access
If you are assigned to use this function and you are working
externally, you can call your office and get access to an external
line in order to make business calls. The business call will be
charged your office extension number or an account number. You
will just be charged for the call to the office.
#
*
The external phone must be of push button type provided with
pound key ( ) and star key ( ) or a mobile phone adapted for
dial tone pulses (DTMF).
After a completed DISA call you must hang up before a new
DISA call can be made.
There are different procedures depending on the type of
Authorization Code, or when an Account Code is used.
z
*72*
z#
z
With common Authorization Code
z
*75*
z*
z#
z
With individual Authorization Code
DT412/DT422/DT432
Call the DISA function at your office.
Dial tone.
Dial.
Dial the Authorization Code and press.
Dial tone.
Dial the external number.
Call the DISA function at your office.
Dial tone.
Dial.
Dial the Authorization Code and press.
Dial your own extension number and press.
Dial tone.
Dial the external number.
97
Alarm
Alarm
Note: The Alarm features are only available for the
DT422 and DT432 phone.
When you work alone and at risk, your personal safety is
important. For situations like this, the DT422 and DT432 phones
are equipped with a red Alarm key on top. When you are in
trouble, just press the Alarm key to summon help by sending a
preset message to the alarm central, which distributes it (requires
an external alarmserver).
Note: The Alarm features may be restricted or not
available. Ask the system administrator for the availability
and for more information.
Alarm with data
Additional data for example a location code, can be sent along
with an alarm. The data must manually be programmed by you.
To use the function, one Soft/Hot key must be defined as a short
cut to the menu Edit alarm data, see section “Hot keys and Soft
keys” on page 107. The stored data is added to all types of alarm
at transmission.
Automatic call after an alarm
The phone can be programmed to call a predefined phone
number directly after an alarm. One Hot key must be
programmed with the specific phone number, see section “Hot
keys and Soft keys” on page 107. It can be any external or
internal phone number but also a pre-defined group of phones.
The phone can be configured to call the same number for all
types of alarms or to call different numbers depending on the
alarm type.
98
DT412/DT422/DT432
Alarm
The automatic call can be programmed with speech monitoring,
i.e. the microphone on the phone that sends the alarm is
discreetly activated and will give the answering party opportunity
to listen and to take an appropriate decision on how to act.
Personal Alarm
Activate
Press the red Alarm key twice within 2 seconds.
The display shows Personal Alarm and an alarm is sent to the
alarm central. After that, the phone returns to idle mode.
Note: You can always trigger the alarm, even when you
are speaking, editing your settings or while the phone is
locked.
Cancel
C
Press to cancel the Personal Alarm (see display).
Test Alarm
Press and hold the red Alarm key until the information text is
displayed.
The default information text is Test Alarm.
C
DT412/DT422/DT432
Press to cancel (see display).
99
Alarm
No-movement Alarm and Man-down Alarm
Notes:
This function requires an installed optional alarm module.
The stand-by time will decrease by approximately 25%
when the phone is equipped with the alarm module.
•
The No-movement Alarm will go off when you have not moved
within a preset time (default 30 seconds).
•
The Man-down Alarm will go off when the phone is tilted more
than 45º for a preset time (default 30 seconds), for example if
you fall.
Before an alarm is activated a warning signal sounds and the
No-movement alarm on or Man-down alarm on icon starts to
flash. If you do not cancel the alarm by pressing a key, it is sent
and a sensor inside the phone will alert the preprogrammed
number.
To use any of these features, you have to activate them first. You
can do this via the Settings menu, see section “Settings” on
page 106 or by programming the function as a Hot key or Soft
key, see section “Hot keys and Soft keys” on page 107.
Press and hold the preprogrammed Soft/Hot key, to put the
alarm in operation respectively out of operation.
No-movement/Man-down Alarm is shown in the display when the
alarm is activated.
The No-movement and Man-down Alarms can be deactivated for
ten minutes (programmed by your system administrator). When
the warning signal sounds, press the Mute key to deactivate an
alarm for ten minutes.
A parameter in the phone determines whether or not an Acoustic
Localization Signal (ALS) should sound after a No-movement
and Man-down Alarm. The ALS is silenced by pressing the Mute
key.
Make the alarm active again
When the No-movement Alarm has been sent, it is made active
again by moving the phone or pressing a key. When the Mandown Alarm has been sent, it is made active again by moving the
phone to upright position or pressing a key.
100
DT412/DT422/DT432
Modes
Modes
The phone is equipped with ten modes. Two modes are preset at
delivery and the remaining eight modes are defined by you. The
preset modes are; Normal, and In charger.
The option Switch off is also located in the Modes menu.
Normal mode
The Normal mode is the default mode.
In charger mode
The In charger mode is activated when the phone is placed in the
charger and deactivated when removed, it cannot be manually
selected. Your last selected mode is automatically chosen when
the phone is removed from the charger.
User defined modes
Eight modes can be defined and saved by you. The modes can,
for example, be used to create a special headset mode with
different ring signal volume and automatic answer of incoming
calls.
Another example is when several users are sharing the same
phone. Each user can then define his own settings, for example;
type of ring signal, volume, answering method, Soft key settings
etc. Note that one has to change to the user defined modes
manually.
DT412/DT422/DT432
101
Modes
ç
à á
ã
â ã
or
or
Select
ç
ç
à á
ã
â ã
á
or
or
ç
102
Change modes
Press.
The last used tab is marked.
Select Modes.
Press to enter Modes.
A list with all modes is shown. See also section “Menu structure”
on page 22.
Scroll up or down until you find the required mode.
Press (see display).
The name of the selected mode is shown.
Note: A Soft/Hot key can also be programmed to change
modes, see section “Hot keys and Soft keys” on
page 107.
Press to leave the Modes menu.
Change mode settings
Press.
The last used tab is marked.
Select Modes.
Press to enter Modes.
A list with all modes is shown. See also section “Menu structure”
on page 22.
Scroll up or down until you find the required mode.
Press to view the settings.
The settings are basically the same as in the Settings menu, but
you also have the possibility to set Absent on/off, choose
answering method, and give the mode a new name. See sections
“Absent” on page 86, “Change answering method” on page 34
and “Settings” on page 106.
Note: It is possible to set that a mode should not be
shown in the list. This is an easy way to hide modes that
are not used. See section “Customizing the menus” on
page 26.
Press to leave the Modes menu.
DT412/DT422/DT432
Services
Services
ç
à á
ã
or
ç
To enter the Services menu
Press.
The last used tab is marked.
Select Services.
Press to enter Services.
A list with all created services is shown. See also section “Menu
structure” on page 22.
Press to leave the Services menu.
Change service
â ã
or
When you have entered Services:
Scroll up or down until you find the required service.
Services
Open door
>
Get lab results
Require wheelchair
Add
Select
Delete
Select
Press (see display).
The service is activated. If data is sent, the text Sending is shown.
Note: You can also open a service by programming a
Soft/Hot key. See section “Hot keys and Soft keys” on
page 107.
DT412/DT422/DT432
103
Services
Create a new service
When you have entered Services:
Add
å
Save
ã
Change
â ã
Select
å
or
Save
104
Press (see display).
Name:_ is displayed.
Enter a name that describes the service you want to add.
For example, if you want this service to open a door, then name it
Open door.
Press (see display).
The new name is marked and added to the list.
Press.
Function: Not used is marked.
Press to enter functions (see display).
The available functions are; Data send, Data with prefix, Phone
call, and SMS.
Choose the function you want the service to have.
Press (see display).
Enter data, prefix, phone number, or SMS address and text.
Press to save the setting (see display).
The new service is saved.
DT412/DT422/DT432
Services
Edit a service
â ã
á
Edit
å Save
ã
Change
â ã
Select
å
or
or
Save
When you have entered Services:
Scroll up or down until you find the service you want to edit.
Press.
Press to change the name (see display).
Change the name and press (see display).
Press.
Press (see display).
Choose the function you want the service to have.
Press (see display).
Enter data, prefix, phone number, or SMS address and text.
Press to save the setting (see display).
The service is changed.
Delete a service
â ã
or
Delete
When you have entered Services:
Scroll up or down until you find the service you want to
delete.
Press (see display).
Delete service?
No
Yes
DT412/DT422/DT432
Yes
Press (see display).
Entry deleted is shown for one second and the service is
deleted.
105
Settings
Settings
Notes:
Some settings can also be controlled via the Modes
menu, see section “Modes” on page 101.
The alert signals are described in section “Audible
Adjustments” on page 119.
ç
à á
ã
â ã
ç
or
or
106
To enter the Settings menu
Press.
The last used tab is marked.
Select Settings.
Press to enter Settings.
A list with all available settings is shown.
Scroll up or down until you find the required setting.
Press to leave the Settings menu.
DT412/DT422/DT432
Settings
Alarm settings
Note: The Alarm settings are only available for the DT422
and DT432 phones.
Deactivate/Activate No-movement/Man-down Alarm
ãá
â ã
or
Change
When you have entered Settings:
Select Alarm settings.
Select No-movement or Man-down.
Press (see display).
The checkbox for the selected alarm is marked/unmarked.
Hot keys and Soft keys
By programming Soft/Hot keys, you can make calls or activate a
function by simply pressing one key. The programmed numbers
and functions are stored on the SIM card of your phone.
In idle mode the Soft keys can be used for specific functions
defined by you. The function can be to dial a specific phone
number, sending mobile data, a short cut to the menu, or sending
SMS. It can also be a link, for example to a central Phonebook.
When navigating the menu structure the Soft keys are used for
different choices in the menu.
A Hot key is one of the ordinary number keys 0 to 9. A Hot key
can have the same function as a Soft key, see above.
Note: The possibility to define a Hot key can be locked by
your system administrator.
To make a call with a Soft/Hot key, see section “Dial a number via
Hot key or Soft key” on page 47.
DT412/DT422/DT432
107
Settings
Activate a function or number with a preprogrammed Soft
key or a preprogrammed Hot key
Absent
å
Press the preprogrammed Soft key (see display),
The pre-set function will be activated, in this example Absent.
or
press and hold the preprogrammed Hot key.
A number between 0 and 9. The pre-set function will be
activated.
Available functions
Data send - See section “Send mobile data” on page 88.
Data with prefix - See section “Send mobile data” on page 88.
Phone call - You program a key with a name and a number.
Short-cut - A short cut to any of the following functions:
•
Absent - See section “Absent” on page 86.
•
Local phonebook - See section “Phonebook” on page 51.
•
Central phonebook - See section “Phonebook” on page 51.
•
Services - See section “Services” on page 103.
•
Switch off - See section “Switching On/Off” on page 29.
•
No-movement Alarm *
•
Man-down Alarm *
•
Edit alarm data *
•
Change system - See section “Change system” on page 117.
•
Demo Mess 1
•
Demo Mess 2
•
RSSI
* Only available for the DT422 and DT432 phones. See
section “Alarm” on page 98.
SMS - See section “SMS (Short Message Service)” on page 87.
Change mode - See section “Change modes” on page 102.
Not used - If you do not need a function or a phone number any
longer, you can set the key to Not used.
108
DT412/DT422/DT432
Settings
Program a Hot key or a Soft key with a phone number
ãá
â ã
á
or
Edit
å Save
ã
Change
ã
Select
å
When you have entered Settings:
Select Soft key or Hot key.
Select key.
For the Soft keys you can select keys Left, Middle or Right and
for the Hot keys you can select keys 0 to 9.
Press.
Press (see display).
Name: is displayed.
Enter the name and press (see display).
Changes saved is displayed. How to write text, see section “Enter
names and numbers” on page 52.
Press.
Function: is marked.
Press (see display).
Select Phone call.
Press (see display).
Enter the phone number.
Notes:
If you program an external number, you have to enter the
prefix digit for external call access (e.g. ).
0
* #
You can also store codes that contain or . You can for
example turn on/off the tone sender in the entered
number by making a long press on the * key (e.g. when
calling telephone banks). Tone sender on will be indicated
with a T in the number, and off with -.
Save
Press to save the setting (see display).
The key is programmed and the name of the selected function is
shown.
Repeat the procedure to program a new key or edit a
programmed key.
DT412/DT422/DT432
109
Settings
Program a Hot key or a Soft key with a function
ãá
â ã
á
or
Edit
å Save
ã
Change
â ã
or
Select
When you have entered Settings:
Select Soft key or Hot key.
Select key.
For the Soft keys you can select keys Left, Middle or Right and
for the Hot keys you can select keys 0 to 9.
Press.
Press (see display).
Name: is displayed.
Enter the name and press (see display).
Changes saved is displayed. How to write text, see section “Enter
names and numbers” on page 52.
Press.
Function: is marked.
Press (see display).
Select the required function.
See section “Available functions” on page 108.
Press (see display).
The following prerequisites apply:
Data send - Enter data if you want to predefine it, or leave it out if
you want to enter data after pressing the Soft key.
Data with prefix - Enter prefix.
Short-cut - Assign the short cut.
SMS - When SMS address is shown you can leave it blank, or
you can predefine a destination address. You can also predefine
the SMS text.
Change mode - Mark the mode that should be changed to.
Not used - Not used will be indicated in the Soft key list.
Save
or
Select
Press to save the setting (see display).
The key is programmed and the name of the selected function is
shown.
Repeat the procedure to program a new key or edit a
programmed key.
110
DT412/DT422/DT432
Settings
Language
The display messages are available in eleven languages:
Danish, Dutch, English, Finnish, French, German, Italian,
Norwegian, Portuguese, Spanish, and Swedish.
ãá
á
â ã
or
Select
When you have entered Settings:
Select General.
Select Language.
Select the required language.
Press (see display).
The selected language is shown.
Change text size
Note: This function is only available for the Cordless
DT412 and DT422 phone.
You can change the text size in the display.
ãá
ã
á
â ã
or
Select
DT412/DT422/DT432
When you have entered Settings:
Select General.
Select Text size.
Press.
Select the text size.
You can choose between Small and Medium.
Press (see display).
Selected size is shown.
111
Settings
Phone lock
You can protect your phone from being used by others by locking
it. You can lock the phone manually or automatically. The
Padlock icon indicates when your phone is locked.
Note: When the phone is locked, it is still possible to send
all types of alarms.
Lock the phone manually
ãá
ãá
á
Select
When you have entered Settings:
Select General.
Select Phone lock.
Select Lock phone.
Press to lock your phone (see display).
Lock the phone automatically
With this function your phone is locked automatically when
placed in a charger or switched off.
Note: This function requires a SIM card parameter
setting. The function can only be enabled/disabled in the
SIM card, not from the phone.
Unlock the phone
The phone can only be unlocked with the lock code. The lock
code is preprogrammed on the SIM card and can be changed
from the phone, see section “Set lock code” on page 113.
å
112
With the phone switched on:
Dial your lock code.
DT412/DT422/DT432
Settings
Set lock code
The lock code consist of one to four digits and you can change it
from your phone.
ãá
ãá
ã
á
Select
å
Save
When you have entered Settings:
Select General.
Select Phone lock.
Select Set lock code.
Press.
Press (see display).
Dial your lock code (one to four digits).
Press to save the lock code (see display).
Clock settings
If the clock and date is set, you can on the same day a message
or call is received, see the time for it.
Set the clock to get the time automatically from the system
ãá
ã
á
â ã
or
Select
When you have entered Settings:
Select General.
Select Clock.
Press.
Select Auto setting.
Press (see display).
Auto setting is shown.
Set the clock manually
When you have entered Settings:
DT412/DT422/DT432
113
Settings
ãá
ã
á
â ã
Select
å
or
Save
Select General.
Select Clock.
Press.
Select Manual setting.
Press (see display).
Enter time, year, month, and day according to the example
below.
Example: Time:0815, Year:2002, Month:03, Day:30.
Press (see display).
The setting is saved.
Set the clock to be visible/invisible in idle mode
ãá
ã
Change
114
When you have entered Settings:
Select General.
Select Clock.
Press (see display).
The clock checkbox is marked/unmarked.
DT412/DT422/DT432
Settings
Automatic key lock
You can set the keypad to lock after 20 seconds after the last
usage. In idle mode a locked keypad is indicated by the Key icon.
ãá
ã
Change
When you have entered Settings:
Select General.
Select Auto key lock.
Press (see display).
The Auto key lock checkbox is marked/unmarked.
Lock the keypad
ç*
The following procedure describes how to manually lock/unlock
the keypad, but it is recommended to always have the automatic
lock on.
Press to lock/unlock the keypad.
The Key icon indicates when your keypad is locked.
Quick answer
When this function is activated, you can answer incoming calls by
simply taking the phone out of the desktop charger. There is no
need to press the Call key.
ãá
ã
Change
DT412/DT422/DT432
When you have entered Settings:
Select General.
Select Quick answer.
Press (see display).
The Quick answer checkbox is marked/unmarked.
115
Settings
Set new messages to be displayed upside
down
Your incoming messages can be displayed upside down.
ãá
ã
Change
When you have entered Settings:
Select General.
Select New message rotated.
Press (see display).
The New message rotated checkbox is marked/unmarked.
Note: When this is set, the call information for incoming
calls is also displayed upside down.
Owner ID
With this function, you can program your personal owner ID.
ãá
ã
Edit
å
Save
116
When you have entered Settings:
Select General.
Select Owner ID.
Press (see display).
Enter your Owner ID.
The phone is changing to text entry mode automatically. How to
write text, see section “Enter names and numbers” on page 52.
Press (see display).
The new ID is shown.
DT412/DT422/DT432
Settings
Display Contrast
With this setting, you can adjust the LCD contrast for best
reading comfort.
ãá
ãá
â ã
or
Select
When you have entered Settings:
Select General.
Select Display contrast.
Select the desired contrast setting.
Press (see display).
The selected setting is confirmed.
System
Use this menu to select a system and view all phone related
information. If you are often moving between systems, it might be
convenient to change system quickly, therefore you can set this
function as a Soft key, or Hot key. See also section “Installation”
on page 123.
Note: The Register option may only be performed by the
system administrator and is described in a separate
documentation.
Change system
When you have registered to more than one system, you can
manually select which system to connect to. You can connect to
up to four different exchange systems with your phone, normally
named A, B, C and D.
When you have entered Settings:
DT412/DT422/DT432
117
Settings
ãá
á
â ã
or
Select System.
Select Select system.
Select the required system.
Note: The normal setting is Auto. This setting makes the
phone automatically look and connect to a system.
Select
Press (see display).
System selected is shown.
System information
The Information menu shows general information about your
phone and your network connection.
ãá
ã
á
When you have entered Settings:
Select System.
Select Information.
Press.
You can view the following information:
IPDI
IPEI
SW version
AP SW
version
The unique global GAP registration number for
the SIM card.
The unique global GAP registration number for
the phone.
Here you can see which version of the phone
software you have.
The alarm module software. If the alarm
module is not connected, it will be indicated
with NC (Not Connected).
Notes:
You cannot alter these settings.
*#46#
You can also view the system information via the quick
access code. The code is
.
118
DT412/DT422/DT432
Audible Adjustments
Audible Adjustments
In order to satisfy your personal needs, your phone is equipped
with many options to set and adjust a personal volume and ring
signal. In addition to this there is a vibrator option.
Your phone is delivered with a set of standard audio settings for
best audio quality. In some environments, for example one with a
high noise level, these standard values might have to be adjusted
to get good audio quality. There are different SIM card settings
for normal conversation, and when loudspeaking function or
headset is used. Ask your system administrator if you require a
different setting.
Volume control
Use the volume keys to adjust the volume in the earpiece.
See section “Description” on page 11 for the location of volume
controls.
To turn the microphone on or off during a call, see section “Mute
microphone” on page 59.
Loudspeaker volume
When you are making a call, the volume keys affect the
loudspeaker volume. This is useful when e.g. you enter a
machinery room.
Press the volume controls to adjust the loudspeaker volume
during a call.
The volume level is set and maintained until you adjust the
volume again.
DT412/DT422/DT432
119
Audible Adjustments
Ringer volume
ç
à á
ã
á
á
â ã
or
or
There are 5 audible ringer levels and one silent level. You can set
the ringer volume via the Alert signals menu.
Press.
The last used tab is marked.
Select Settings.
Press to enter Settings.
A list with all available settings is shown.
Select Alert signals.
Select Volume.
Select the required volume level.
You have six available alternatives; Level 1 to 5, or Silent.
If you want to hear the volume level during the changing:
Play
Select
Press (see display).
The marked volume is played until you press Stop or Select.
Press to select the volume (see display).
The selected volume is shown.
Mute audible signals
To mute the ring signal before answering a call, see section
“Mute ring signal” on page 33. See section “Description” on
page 11 for the location of the Mute key.
You can also turn the ringer off permanently. When the phone is
on-hook (idle mode):
Press and hold the Mute key on the right side of the phone.
The Ringer off icon is shown. Now only the vibrator and the red
lamp will indicate an incoming call.
Note: High priority messages will override this setting.
This action will also mute message signals.
Press and hold the Mute key to turn the ringer on again.
The Ringer off icon disappears.
120
DT412/DT422/DT432
Audible Adjustments
ç
à á
ã
á
ã
á
â ã
á
â ã
or
or
or
Ring signals
Press.
The last used tab is marked.
Select Settings.
Press to enter Settings.
A list with all available settings is shown.
Select Alert signals.
Select Ring signals.
Press.
Select the required call type.
You can change the ring signal for Internal calls, External calls, or
Callback calls.
Press.
Select the required signal.
Available alternatives are; Beep, Low, Medium, High, and Mixed.
If you want to hear the new signal during the changing:
Play
Select
DT412/DT422/DT432
Press (see display).
The marked ring signal is played until you press Stop or Select.
Press to select the ring signal (see display).
The selected ring signal is shown.
121
Audible Adjustments
Key beep
ç
à á
ã
á
ã
or
Change
Use this feature to set if you want every keystroke to be
confirmed with a short tone or not.
Press.
The last used tab is marked.
Select Settings.
Press to enter Settings.
A list with all available settings is shown.
Select Alert signals.
Select Key beep.
Press (see display).
The Key beep checkbox is marked/unmarked.
Vibrator
ç
à á
ã
á
ã
or
Change
You can set the vibration alarm instead of the ring signal to
indicate incoming calls and messages.
Press.
The last used tab is marked.
Select Settings.
Press to enter Settings.
A list with all available settings is shown.
Select Alert signals.
Select Vibrator.
Press (see display).
The Vibrator checkbox is marked/unmarked. A call will now be
indicated by both the vibrator and the ring signal. If you want only
the vibrator to indicate calls, you have to mute the ring signal first.
Note for DT432: Loudspeaking disables the vibrator. The
vibrator is active after the beep and never during a beep.
122
DT412/DT422/DT432
Installation
Installation
This chapter describes how to connect and charge the battery of
your phone. You will also find procedures for installation and
maintenance of your phone.
Note: If you have a DT412 or a DT422 phone, you need
to know what version of the phone you are using, as only
certain battery packs are compatible with each version.
Check the phone label to see the phone version. If the
label starts with “RAID2-” your phone is a version two
phone.
ATEX battery and charging information (DT432)
DT412/DT422/DT432
•
It is only allowed to use the special ATEX battery pack
together with the DT432 ATEX phone. Using a standard
battery pack will void the ATEX approval.
•
The DT432 ATEX phone may only be charged in the ATEX
desk top charger II and in rack charger II.
123
Installation
Battery
All batteries are rechargeable.
Charging the battery
The battery requires charging when the Battery icon in the
display is empty.
Place the phone in the charger. A beep indicates connection with
the charger. The charging status is shown by the Battery icon in
the display. A fully charged phone is indicated by a filled Battery
icon. If the phone is switched off when placed in the charger, it
will start up automatically within 2 minutes.
Note: If a call is connected when the phone is placed in
the charger, the call will be disconnected.
Removing the battery
The battery is fastened by a screw and two hooks. To remove the
DT412 and DT422 battery, use a small coin and turn the screw to
horizontal position. To remove the DT432 battery, use the key
which is delivered with the phone and turn the screw to horizontal
position. Remove the battery by pulling the screw. When
fastening the battery again the screw has to be in horizontal
position.
Note: Avoid using a screwdriver as it may damage the
screw.
Battery handling
The battery contains environmental polluting material. If
damaged, return it to a collecting point.
Note: Only use the charger that is delivered with your
phone to charge the battery.
124
DT412/DT422/DT432
Installation
Chargers
Desktop charger
The desktop charger is used for charging your phone, but also for
storing it when you are placed at one location, for example at
your desk. The tilted design facilitates the use of handsfree
operation, i.e. in loudspeaking mode. The charger is delivered
with a plug-in power supply and is connected into an ordinary
wall socket.
Important!
Only use the equipment designed for the DT412/DT422/DT432
phones, see below.
Battery
type
Battery pack
article number
Charger article
number
Programmer article
number
Rack charger article
number
Battery pack adapter
for rack charger
NTM/DPYNB 220 21/1,
NTM/DPYNB 220 21/2,
NTM/DPYNB 220 21/3
or DPY 901 624/1
NTM/DPYNB 220 28/1, DPYNB 101 54/1
NTM/DPYNB 220 28/2, (*BMLNB 101 54/1)
NTM/DPYNB 220 28/3 or DPY 901 642/1
or LTT 999 07/1
DPYNB 220 29/1
or DPY 901 495/1
Only
BKBNB 902 44/1
NTM/DPYNB 220 21/1,
NTM/DPYNB 220 21/2,
NTM/DPYNB 220 21/3
or DPY 901 624/1
NTM/DPYNB 220 28/1, DPYNB 101 54/1
NTM/DPYNB 220 28/2, (*BMLNB 101 54/1)
NTM/DPYNB 220 28/3 or DPY 901 642/1
or LTT 999 07/1
Only
DPY 901 495/1
Only
DPY 901 639/1
Only
DPY 901 624/1
Only
LTT 999 07/1
Only
DPY 901 495/1
DT412 and DT422
NiMH
Only
BKBNB 220 21/1
DT412 v2 and DT422 v2
Li-Ion
DT432
Li-Ion
Only
DPY 901 642/1
* power supply.
DT412/DT422/DT432
125
Installation
Charging rack
Note: See also separate installation guide, supplied
together with your phone.
022
The charging rack is used for charging your phone and/or spare
batteries. When charging spare batteries an adapter is needed.
The wall mounted charging rack and its power supply are
modular systems which enables a number of installation
configurations.
Each power supply can support three charging racks with four
positions for phones and/or batteries in each rack (see technical
specifications for the charging rack).
As the phone cannot distinguish between a desktop charger and
the charging rack, it is recommended that the alert signal is
silenced when placed in a rack, see section “Audible
Adjustments” on page 119. There is also a SIM parameter that
can be set in the SIM card programmer by your system
administrator.
126
DT412/DT422/DT432
Installation
Belt clip
The clip on the back of the phone helps you fasten it to a belt or
similar. It is also possible to change the clip to a swivel-type or if
no clip is needed, to replace it with a covering plate.
Change the hinge-type clip
A hinge-type belt clip is mounted on the phone at delivery. The
clip can be replaced with a cover plate that is in the delivery or a
swivel-type belt clip that can be ordered separately.
The required tool is a Pozidriv Point size 1.
Unscrew and replace the clip.
DT412/DT422/DT432
127
Installation
SIM card
All your personal phone settings are programmed and stored in
the Subscriber Identity Module (SIM) card.
The SIM card provides you with personal mobility as you can
easily move it to another cordless phone, enabling you to receive
calls, make calls and keep all your personal settings such as
Phonebook, identity, alert signal, and your defined functions of
the Soft keys and Hot keys
Changing the SIM card
Remove the battery as described.
See section “Battery” on page 124.
Slide the SIM card out of position.
Insert the new SIM card and slide it into position.
Changing SIM parameters
The SIM card parameters can be altered from the phone but also
by using a SIM card programmer. The parameters can be saved
to file from the SIM card programmer software to be able to give
the same parameter settings to several phones.
The file can also be used to reset the parameters to default
values. The SIM card programmer is delivered with a CD
containing required software.
DT412/422/432 functionality using a DT400/410/420/430
SIM card
The phone can be used with a SIM card for the DT400/410/420/
430 phones but the functionality will be limited as described
below:
128
•
Man-down alarm does not work.
•
Central phonebook from Contacts menu is not available.
•
Modes are not available.
•
Switch off from Modes menu is not possible.
•
Services are not available.
•
Internal/External and Callback call has same ring signal
setting.
DT412/DT422/DT432
Installation
•
Soft keys cannot be used.
•
Some Hot key short-cuts cannot be used
DT412/422/432 functions that are working:
• Phone calls to and from the phone
• Messages
• SMS from the phone
• Interactive Messaging
• Push-button alarms
• No-movement alarm
Hot keys
The DT400/410/420/430 and DT412/422/432 do not have the
same set of Hot key functions. When the Hot keys on a DT400/
410/420/430 SIM card are programmed with functions, the
following applies:
DT400/410/420/430 function
DT412/422/432 short-cut
Manual absent on
Manual absent off
Switch off
Change system
No-movement alarm on
No-movement alarm off
Edit alarm data
RSSI
Demo message 1
Demo message 2
Absent on/off
Switch off
Change system
No-movement alarm on/off
Man-down alarm on/off
Edit alarm data
RSSI
Demo message 1
Demo message 2
It is not possible to program the DT400/410/420/430 SIM card
with the short-cuts Local phonebook and Services.
Note: If a Hot key indicates Man-down alarm when a
DT400/410/420/430 SIM card is used, the phone will
indicate Wrong SIM when the Hot key is pressed.
DT412/DT422/DT432
129
Reference
Reference
This section describes the terminology used on the display, the
phone communication signals, technical specifications, spare
parts and accessories.
Terminology
The list below explains the terms which may appear on the
display.
Terminology used in display
Term
Meaning
IPDI
International Portable part Equipment Identity, unique
identity assigned to your SIM card.
International Portable part Equipment Identity, unique
identity assigned to your phone by the manufacturer.
Portable Access Rights Key, unique identity assigned
to your network.
Here you can see which version of the phone software
you have.
Here you can see which version of the Alarm software
you have.
IPEI
Park
SW
AP SW
130
DT412/DT422/DT432
Reference
Phone signals
The phone is signalling certain events audibly and visually as
described below.
Signal
Meaning
Red warning light Incoming call.
Message waiting.
The phone also generates audible ring signals and alarm signals.
Sound
Meaning
Ring signal
Alarm signal
Incoming call.
1 short beep: phone is out of range of base
system.
Message beep: Incoming message.
No-movement alarm or Man-down alarm
about to be sent (DT422 and DT432 only)
You hear this each time you press a key
(when selected).
Key beep
DT412/DT422/DT432
131
Reference
Optional accessories
All of the following accessories are optional and can be
purchased at your local Aastra contact.
Belt clip, swivel-type
The ordinary belt clip can be replaced with a special swivel-type
belt clip adapted to firmly place your phone onto your belt.
Leather casing
The leather casing is especially designed for the phone. The
casing comes with the swivel-type belt clip and the phone is fully
operational while placed in the casing.
Note: The leather case may not be used in potentially
explosive areas.
Headset
A headset is recommended if you frequently use the phone, and/
or want to have both hands free. The phone has a special
headset connector that is waterproof. The headset comes in
three versions; with microphone integrated in the cable (with or
without adapter), with microphone on a boom, and with hearing
protection (Peltor). An adapter, that makes it possible to connect
other standard types of Peltor headsets, is also available.
Notes:
The phone must be equipped with the factory mounted
headset connector.
The headset answering button is only active during a call
or when the phone is ringing and cannot be used to get a
line when making a call.
Microphone integrated in the cable, microphone on a
boom and headset adapter may not be used with DT432.
ATEX headset information (DT432)
•
132
It is not allowed to use any other headsets than the Peltor
ATEX headsets connected via the ATEX headset adapter.
Using any other headset or headset adapter will void the
ATEX approval.
DT412/DT422/DT432
Reference
Security chain
The security chain is 800 mm long. Fasten one end to the hingetype belt clip and the other end to, for example, your pocket.
Additional accessories
•
DT412/DT422/DT432
Standard clip, hinge-type
•
Desktop charger
•
Spare battery
133
Troubleshooting
Troubleshooting
This section contains information on how to solve common
operational problems, and warnings you may receive.
Go through the following lists if you encounter any problems. If
this checklist does not solve the problem, contact your system
administrator. If others have similar problems, there may be a
system error.
Fault / Display
Probable cause
The phone does
not switch on
No display
The battery level is
low.
The battery level is
low or the phone is
defective.
The Ringer off icon
is on or the phone
is defective.
The battery level is
low or the phone is
defective.
The battery level is
low or the phone is
defective.
The phone is
defective.
No ringing
Battery icon
flashes
Call icon is
switched off after
2 seconds
Lamp shows
steady light
When adding
names to the
Phonebook, an
error beep sounds
Wrong sim
134
Action or
comment
Charge the
battery.
Charge the battery
or contact system
administrator.
Off icon on =
Turn on the ringing
signal.
Charge the
battery.
Charge the battery
or contact system
administrator.
Contact system
administrator.
The memory is full,
you cannot add
new names.
Delete a name.
The SIM card is
not compatible
with the software
version of the
phone.
Contact system
administrator.
DT412/DT422/DT432
Troubleshooting
DT412/DT422/DT432
Fault / Display
Probable cause
Action or
comment
Check SIM card
The SIM card is
missing or inserted
the wrong way.
Insert or adjust the
SIM card or
contact system
administrator.
Keys locked
Unlock
The key pad is
locked.
Press Menu key
followed by .
No System
Cannot connect to
the network, the
phone is not
registered or out of
range.
Contact system
administrator.
*
135
Glossary
Glossary
136
DECT
Digital Enhanced Cordless Telephony.
Exchange
Switch. Your telephone switching system.
Idle mode
The state your phone is in when nothing is activated; not
calling, not ringing, not diverted etc.
Least Cost Routing
A function that automatically selects the cheapest way to
connect your external call (not necessarily the shortest
distance).
Speed Dialing number
Abbreviated number or short number, used for making
frequently used numbers faster to dial.
Third party
A third connection (person), which can be included in an
ongoing two person conversation. The connection can be
internal or external.
DT412/DT422/DT432
Index
Index
A
Absence Information 78
Absent 86
Account Code 94
Add a name and a number to the
PhoneBook 55
Alarm 98
Automatic call after 98
No-movement Alarm and Man-down
Alarm 100
Personal Alarm 99
Test 99
With data 98
Alarm settings 107
Alarm with data 98
Answer calls 32
Audible adjustments 119
Key beep 122
Ring signals 121
Vibrator 122
Volume control 119
Authority 48
Authorization Code, common 48
Authorization Code, individual 49
Automatic call after an alarm 98
Automatic key lock 115
B
Battery 124
Belt clip 127
Bypass 46
C
Call Forwarding 64
External Follow-me 66
Internal Follow-me 64
Personal Number 68
Setting form for search profiles 74
Call Waiting 45, 60
DT412/DT422/DT432
Callback 43
Change a name and a number in the
PhoneBook 56
Change answering method 34
Change modes 102
Change services 103
Change system 117
Change text size 111
Chargers 125
Charging the battery 124
Cleaning 10
Clock settings 113
Common Bell Group 92
Conference 61
Copyright 5
Create a new service 104
D
Declaration of Conformity 5
Delete a name and a number from the Phone
book 57
Delete a service 105
Description 11
Display information 14
Menu structure 22
Switching on/off the Cordless 29
Tones 28
Dial number from the Call list 41
Dialing during a connected call 62
DISA = Direct Inward System Access 97
Display contrast 117
Display information 14
Idle telephone 15
Incoming call 17
Outgoing call 16
During calls 58
Call Waiting 60
Conference 61
Dialing during a connected call 62
137
Index
Handsfree 58
Inquiry 59
Mute microphone 59
Push-to-talk button 63
Put a call on hold 62
Transfer 60
E
Edit a service 105
Emergency mode 96
Enter names and numbers 52
Enter the PhoneBook 54
External Follow-me 66
F
Free Seating 31
G
General Deactivation 95
Glossary 136
Group Call-pick-up 92
Group features 92
Common Bell Group 92
Group Call-pick-up 92
Group Hunting 93
Group Hunting 93
H
Handsfree 58
Hot Keys and Soft keys 107
I
Important user information 6
Cleaning 10
Intrinsic safety 9
Preparing for use 10
Safety information 9
SIM card 9
Incoming calls 32
Answer calls 32
Change answering method 34
Handsfree 33
Parallel Ringing 35
Information 78
Inquiry 59
Installation 123
Battery 124
Belt clip 127
Chargers 125
SIM card 128
138
Interactive Messaging 88
Internal Follow-me 64
Intrinsic safety 9
Intrusion 45
K
Key beep 122
L
Language 111
Last External Number Redial 40
M
Mailbox 91
Make a call via the PhoneBook 54
Make calls 37
Malicious Call Tracing 96
Man-down Alarm 100
Manual Message Waiting (MMW) 82
Menu structure 22
Messages 81
Absent 86
Interactive Messaging 88
Manual Message Waiting (MMW) 82
SMS 87
Text messages 84
Voice Mail 89
Modes 101
Change 102
Mute microphone 59
N
Night Service 95
No-movement Alarm 100
Number Presentation Restriction 40
O
Optional accessories 132
Other useful features 94
Outgoing calls 37
Authority 48
Bypass 46
Call Waiting 45
Callback 43
Dial number from the Call list 41
Handsfree 38
Intrusion 45
Last External Number Redial 40
Make calls 37
Number Presentation Restriction 40
DT412/DT422/DT432
Index
Speed Dialing 47
When you receive a busy tone 43
Owner ID 116
P
Parallel Ringing 35
Personal Alarm 99
Personal Number 68
Phone book
Delete a name and a number 57
Phone lock 112
Phone signals 131
PhoneBook 51
Add a name and a number 55
Change a name and a number 56
Enter 54
Enter names and numbers 52
Make a call 54
Save a number from the Call list to the
PhoneBook 55
Preparing for use 10
Push-to-talk button 63
Put a call on hold 62
Q
Quick answer 115
R
Reference 130
Remote 75, 76, 77
Ring signals 121
S
Safety information 9
Safety instructions 6
Save a number from the Call list to the
PhoneBook 55
Services 103
Change 103
Create 104
Delete 105
Edit 105
DT412/DT422/DT432
Set new messages to be displayed upside
down 116
Setting form for search profiles 74
Settings 106
Alarm 107
Automatic key lock 115
Change text size 111
Clock 113
Display contrast 117
Hot Keys and Soft keys 107
Language 111
Owner ID 116
Phone lock 112
Quick answer 115
Set new messages to be displayed upside
down 116
System 117
SIM card 9, 128
SMS 87
Speed Dialing 47
Switch on/off 29
System 117
T
Terminology on display 130
Test Alarm 99
Text messages 84
Tones 28
Transfer 60
Troubleshooting 134
U
Unlock the phone 112
V
Vibrator 122
Voice Mail 89
Volume control 119
W
Warranty 5
Welcome 4
When you receive a busy tone 43
139
Subject to alteration without prior notice.
For questions regarding the product,
please contact your Aastra certified Sales Partner.
Also visit us on http://www.aastra.com
© Aastra Telecom Sweden AB 2010. All rights reserved.
EN/LZT 103 67 D
Download PDF