Quick Installation Guide SkyIPCam1747W

Quick Installation Guide SkyIPCam1747W
Quick Installation Guide
SkyIPCam1747W
Wireless N Night Vision Pan & Tilt Network Camera
Model # AICN1747W
Ver. 1A
Package Contents
•
•
•
•
•
•
•
•
Wireless N Night Vision Pan & Tilt Network Camera
Antenna
Wall Mount Kit
GPIO Connector
Power Adapter
Ethernet Cable (Cat.5)
Setup CD
Quick Installation Guide
System Requirement
• Accessing the Camera using Web Browser
- Supported Browsers*: Microsoft® Internet Explorer 6.0 or above;
Apple Safari, Mozilla Firefox with JAVA plug-in
­ CPU:
Intel Pentium III 800MHz or above
­ RAM:
512MB
­ Resolution:
800x600 or above
• Accessing the Camera using Software SkyIPCam UltraView
­ Platform:
Microsoft® Windows® 7, Vista and XP
­ Hard Disk:
80GB or above
­ Resolution:
1024x768 or above
­ Suggested Hardware Requirement*
▪ 1~8 cameras connected: Intel Core 2 Duo; 2GB RAM
▪ 9~32 cameras connected: Intel Core 2 Quad; 4GB RAM
NOTE If you connect multiple cameras to monitor various places
simultaneously, it is recommended that you use a higher end computer.
* It is recommended to use Internet Explore to view/manage the camera,
because Safari and Mozilla Firefox may not support certain features, such as
configuring motion detection or snapshot.
1
Section 1
This Quick Installation Guide only provides basic instructions. For detailed
information on using this product, please refer to the User’s Manual on the
supplied CD.
Getting Started
Step 1.1 Attach the included external antenna to the camera.
Step 1.2 Connect one end of the Ethernet cable to the IP Camera and connect
the other end to one of the LAN ports on your router or switch.
Step 1.3 Power on the IP Camera by connecting one end of supplied power
adapter to the power jack of the Camera and connecting the other end to an
electrical outlet.
Step 1.4 Verify that the orange light (Power) is solid and the green light (Link) is
blinking.
2
Section 2
Installing the SkyIPCam Utility
Step 2.1 Insert the provided CD into your computer’s CD ROM drive.
Step 2.2 Click on Install Utility and Software.
Note: If you do not see the autorun menu pops up on the screen, please go to
your CD-ROM drive > UltraView folder > run “Setup.exe”.
3
Step 2.3 Click Install to install the utility.
Step 2.4 Click Finish when installation finishes.
4
Section 3
Configuring the Camera
Step 3.1 Open SkyIPCam Utility by double clicking on its icon on your desktop.
Step 3.2 Click on Search to find the camera on your network. Select the
Camera you wish to configure and click on Link.
Note If the Camera you wish to configure does not show up in the utility, make
sure the camera is properly connected to the same local network as your
computer is, and the Green LED should be on. Click on Search to try again.
5
Step 3.3 When you are prompted for the username and password, enter
“admin” for both Username and Password, and click OK.
Step 3.4 The camera viewing window will appear. Click on Setup, then click
on Smart Wizard.
1
2
Step 3.5 You may change the default Camera Name and enter a name for the
Location if you like. Then enter “admin” for both Admin Password and
Confirm Password. Click Next.
6
Step 3.6 You can specify a static IP address to this camera by selecting Static
IP, and enter IP, Subnet Mask, Default Gateway, Primary/Secondary DNS
addresses here.
If you are not sure how to configure Static IP Setting, please select DHCP.
Click Next.
Note Be sure to enter Primary/Secondary DNS addresses assigned by
your ISP if you set up Static IP for the camera so that the Email alert / FTP
uploading can function properly.
7
Step 3.7 If you would like to set up email alerts that you can receive in the
future, enter your email information here. You can get this information from
your Email Service Provider. You can set this up at a later time. Click Next.
Step 3.8 Enter the Network ID (SSID) of your wireless network, or click on Site
Survey and select from the list. Select the Authentication and Encryption
modes, and enter the security Key of your wireless network. This information is
stored in your wireless AP/router. Click Next.
Note You may contact the manufacturer of your wireless router/AP’s to find out
its SSID and wireless security settings.
8
Step 3.9 Confirm your settings at this page. If everything is correct, click Apply
to save the settings, then the camera will restart in 50 seconds.
Step 3.10 After the camera is restarted, unplug the network cable from it. It will
take around 1 or 2 minutes for the camera connecting to your wireless
router/AP.
To make sure the wireless connection is successfully established, open the
SkyIPCam Utility and click on Search. If the camera shows up in the list, it is
connected to your wireless network successfully. If not, please verify the SSID
and the wireless security settings you configured at Step 3.8 are correct.
9
Section 4
Viewing Images
Method A > Access Camera from SkyIPCam Utility
Step 4.1A Open Airlink101 SkyIPCam Utility, select the camera you wish to
connect to and click on Link button. Go to Step 4.3.
Method B > Access Camera from Web Browser
Step 4.1B If you assigned a static IP address for your camera (at Step 3.6),
you may open the Web Browser on your computer.
Step 4.2B Type the IP address of your camera in the Address bar, and press
Enter.
10
Step 4.3 Enter administrator’s username and password of the camera, then
click OK. The default username and password are both “admin” if you did not
make any change to it at Step 3.5.
Step 4.4 Internet Explorer User: If this is the first time for your computer to
view image from the web configuration page, you will be prompted to install the
ActiveX Control. Click on the bar on top of the screen and click on Run Add-on
or Install ActiveX Control (depends on different IE versions).
11
Step 4.5 Click on Run, then you will be able to view the image.
Note If you are using Mozilla Firefox or Safari and you are not able to view any
image, please make sure you have Java and Quick Time add-ons installed.
Step 4.6 To get a clear view of images, you can simply rotate the camera’s lens
clockwise or counter-clockwise to adjust the focus.
12
Section 5
Technical Support
E-mail: [email protected]
Toll Free: 1-888-746-3238
Website: www.airlink101.com
* Monitoring multiple cameras simultaneously demands high performance computer system.
** Theoretical maximum wireless signal rate derived from IEEE standard 802.11 specifications.
Actual data throughput will vary. Network conditions and environmental factors, including volume of
network traffic, building materials and construction, mix of wireless products used, radio frequency
interference (e.g., cordless telephones and microwaves) as well as network overhead lower actual
data throughput rate. Compatibility with 802.11n devices from other manufactures is not guaranteed.
Specifications are subject to change without notice. Photo of product may not reflect actual content.
All products and trademarks are the property of their respective owners. Copyright ©2011
Airlink101®
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement