Quick Reference Guide
Pairing Your iOS Device
with
FuzzyScan Bluetooth Cordless Scanner
Rev. A2
Rev. No
A1
A2
Release Date
April 30, 2014
July 28, 2014
Description
First release.
Delete the section “Pair iOS Device via HID Legacy”
Add the section “Pair iOS Device via HID Mode”
There is one HID radio link modes available for Cino FuzzyScan Bluetooth scanner to pair with iOS device – “HID mode” and
“HID Mode with Passkey”. “HID Mode with Passkey”, it is required to enter 4-digit passkey prompted on your iOS device. For
more details, please refer to the “Pocket Scanner QSG”.
This document describes how to pair CINO FuzzyScan Bluetooth Scanner with iOS device through HID connectivity.
Screenshots in this document are all for reference only. The actual screens during the pairing procedure will be varied
depending on the iOS device you use.
Applicable Models:
Bluetooth Image Scanners
z F680BT and F780BT series with firmware version 3.01.04 or above
z PF680BT series with firmware 1.01.01 or above
z F790BT series with firmware 2.05.02 or above
z A770BT series with firmware 1.01.01 or above
Bluetooth Laser Image Scanners
z L680BT series with firmware version 3.01.04 or above
z L780BT series with firmware version 3.01.04 or above
z PL680BT series with firmware version 1.01.01 or above
If your Bluetooth cordless scanner is not with firmware version listed above, please upgrade the firmware.
Preparation
1. iOS device
iOS device with iOS v4.0 or above.
2. FuzzyScan Bluetooth Cordless Scanner with battery fully charged.
1
Pair iOS Device via HID Mode
Step
1.
Power on the scanner within Bluetooth
coverage of your iOS device.
2.
Scan the ”Uninstall” command listed
below.
3.
Enable the Bluetooth® function of your iOS
device to search Bluetooth device (here, it
is CINO’s scanner).
For this procedure, please refer to the User
Manual of your iOS device.
4.
Scan “HID Mode” command.
5.
6.
Visual Signal
status indicator
Acoustic Signal
Screen
link indicator
blinks red and
green
alternatively
During the pairing:
blinks blue 3 times
per 2 Sec.
The scanner will be discovered by and
shown as ”xxxxBT-xxxx” or
“PxxxxBT-xxxx” on the discovered
Bluetooth device list on your iOS device.
Tap the ”xxxxBT-xxxx” or
“PxxxxBT-xxxx” to pair the scanner with
your iOS device.
7.
The pairing is successful.
8.
Launch any data entering App or function
on your iOS device and scan a barcode to
verify the pairing is successful.
blinks blue 1 time
per 2.5 Sec.
4 beeps in
ascending tone
Note: If your iOS device prompts any message or direction not mentioned above, please confirm or follow it.
2
Uninstall
HID Mode
3
Pair iOS Device via HID Mode with Passkey
Step
1.
Power on the scanner within Bluetooth
coverage of your iOS device.
2.
Scan the ”Uninstall” command listed
below.
3.
Enable the Bluetooth® function of your iOS
device to search Bluetooth device (here, it
is CINO’s scanner).
For this procedure, please refer to the User
Manual of your iOS device.
4.
Scan “HID Mode with Passkey”
command
5.
The scanner will be discovered by and
shown as ”xxxxBT-xxxx” or
“PxxxxBT-xxxx” on the discovered
Bluetooth device list on your IOS device.
6.
Tap ”xxxxBT-xxxx” or “PxxxxBT-xxxx”,
a message shows and asks you to enter it
accordingly. Please enter that pin code by
scanning “Numeric Option Codes” and then
the “FIN” command listed in the next page.
7.
The pairing is successful.
8.
Launch any data editor App or function on
your IOS device and scan a barcode to
verify the pairing is successful.
Visual Signal
status indicator
Acoustic Signal
link indicator
blinks red and
green
alternatively
During the pairing:
blinks blue 3 times
per 2 Sec.
blinks blue 1 time
per 2.5 sec.
4
4 beeps in
ascending tone
Screen
Uninstall
FIN (FINISH)
HID Mode with PassKey
Numeric Option Code
2
0
1
4
3
7
5
6
8
5
9
1. iOS device only allows one HID input device to work at any one time. So, as soon as the scanner is connected
with the Apple iOS device, its virtual keypad will disabled by default. As result, virtual keypad and the paired
scanner can not function simultaneously.
2. To re-enable virtual keypad:
a. For both guy type and pocket-sized scanner:
Please scan following "Sleep" command. The virtual keypad of iOS will show up. If you would like to input the
data by scanning the barcode again, please press the scanner’s trigger once.
b. For pocket-sized scanner:
You also can press the function key1 twice to enable the virtual keypad of iOS directly.
Sleep
6
© Copyright Cino Group
© Copyright PC Worth Int’l Co., Ltd
Disclaimer
Cino makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranty of merchantability
and fitness for any particular purpose. Cino shall not be liable for errors contained herein or for incidental consequential damages in
connection with the furnishing, performance, or use of this publication. This publication contains proprietary information that is protected
by copyright. All rights are reserved. No part of this publication may be photocopied, reproduced or translated into any language, in any
forms, in an electronic retrieval system or otherwise, without prior written permission of Cino. All product information and specifications
shown in this document may be changed without prior notice.
7
">
