Denon AVR3310CI - Multi-Zone Home Theater Receiver Owner`s manual

AV SURROUND RECEIVER
AVR-3310CI
Owner’s Manual GAdditional functions editionH
The AVR-3310CI owner’s manual is organized in the following two volumes.
•GThe original versionH
•GAdditional functions editionH·············This version
Le manuel d’utilisation de l’AVR-3310CI est organisé en deux volumes, comme suit.
•GLa version originaleH
•GÉdition des fonctions supplémentairesH··········· La présente version
This version contains descriptions of additional and changed functions only.
The additional and changed functions are items indicated by “
GUI Menu Map (vpage 5)
Manuel de l’Utilisateur GÉdition des fonctions supplémentairesH
” in the GUI Menu Map.
La présente version contient uniquement les descriptions des fonctions supplémentaires
et modifiées.
Les fonctions supplémentaires et modifiées sont signalées par le symbole “
l’interface graphique GUI.
Plan du menu de l’interface graphique GUI (vpage 5)
” dans plan du menu de
ENGLISH
n Additional functions
n Contents
•Addition of Audyssey DSX™
(Dynamic Surround Expansion™)
Getting Started
Part Names and Functions····························································2
Remote Control Unit······································································2
Audyssey Dynamic Surround Expansion™ (DSX)
Realistic reproduction of sound relies on the ability of audio systems
to match human hearing performance. Three key requirements are:
(i) frequency response; (2) dynamic range; and (3) accurate spatial
reproduction. The requirements for frequency response have already
been surpassed with sampling rates that exceed human hearing. The
dynamic range limits of human perception have also been met with
current digital audio systems operating capable of signal to noise ratios
that approach 120 dB. Accurate spatial sound rendering, however, has
not yet reached the limits of perception as human perception relies
on the combination of sounds arriving from many more directions
than what 5.1 surround sound systems provide. Audyssey DSX™
technology was developed to overcome the spatial sound rendering
limitations faced by 5.1 surround sound formats.
The ITU 5.1 channel standard recommends three front loudspeakers
and two rear loudspeakers. The Left (L) and Right (R) front loudspeakers
should be placed at ±30° relative to the central listening position. The
Center (C) loudspeaker should be at 0° and the surround loudspeakers
(SL, SR) should be placed between 100° and 120°. All loudspeakers
must be equidistant from the center listening position or compensated
with time delay if that is not possible. A separate lowfrequency effects
(LFE) channel is used to reproduce additional bass content from the
subwoofer.
There are certain things that 5.1 surround sound systems do well
compared to 2-channel stereo. For example, it is possible to move
sounds across the front seamlessly. It is also possible to create
ambience behind the listener. But 5.1 channel surround systems do not
provide enough channels from which to render the required reflected
sound components for a seamless and enveloping soundstage.
Unfortunately, the additional two back surround channels in 7.1
systems are not in the right place to provide a significant perceptual
improvement.
Adding more channels to a surround system is not for special effects.
Accurate spatial sound reproduction requires rendering of directional
sound cues and non-directional ambient cues. Reflections arriving after
the direct sound play a critical role in the perception of soundstage
width and depth. To have the most impact, additional surround channels
should be used to control the direction, time of arrival, and frequency
response of the reflected sound to render an expanded soundstage
that reproduces sound with better localization and envelopment than
what 5.1 systems provide.
Research in the perception of auditory source width has shown that
there are strong preferences in the direction of reflected sound and
the perception of soundstage width and spaciousness. The single
most important direction of side-wall reflections is ±60°. Audyssey
DSX provides a pair of Wide channels (LW and RW) at ±60° with
appropriate frequency response and perceptual processing to match
the requirements of human hearing. In fact, the Wide channels are
much more critical in the presentation of a realistic soundstage than
then Back Surround channels found in traditional 7.1 systems. A more
enveloping 7.1 channel system is one in which Wide speakers are
used instead of Back Surround speakers. Adding surround channels
behind the listener has a very small impact compared to the increase
in envelopment and soundstage width that the front wide channels
will provide.
After side reflections, the next most important acoustical and perceptual
cues come from reflections above the front stage. Audyssey DSX
provides a pair of Height channels (LH and RH) at a ±45° azimuth angle
and elevated to a 45° angle in the median plane.
In addition to creating new Wide and Height channels, Audyssey
DSX also provides Surround Processing to enhance the envelopment
of the Surround and Back Surround channels (if present). Audyssey
DSX Surround Processing processes the standard surround signals in
the time and frequency domains to improve the perceived sense of
envelopment and blending with the other speakers in the surround
system.
Audyssey Dynamic Surround Expansion is a scalable system that can
adapt to the practical needs of the user. The first level of surround stage
enhancement comes from adding the Wide channels. The second
level comes from adding the Height channels. If it is practical to have
both Wides and Heights then the surround performance will be further
enhanced. Audyssey DSX automatically reconfigures its processing to
optimize surround rendering over any number of available speakers
beyond 5.1.
Manufactured under license from Audyssey Laboratories™. U.S.
and foreign patents pending. Audyssey MultEQ® is a registered
trademark of Audyssey Laboratories. Audyssey Dynamic EQ® is a
registered trademark of Audyssey Laboratories. Audyssey Dynamic
Volume™ is a trademark of Audyssey Laboratories. Audyssey
Dynamic Surround Expansion™ is a trademark of Audyssey
Laboratories.
Connections
Installing / Setting the Speakers··················································3
Speaker Connections·····································································4
Settings
GUI Menu Map···············································································5
Make the Optimal Speaker Settings, and Correct the Room
Acoustics (Audyssey™ Auto Setup)·············································6
Making Detailed Settings (Manual Setup)··································8
Playback
Adjusting the Sound and Picture Quality
(Audio/Video Adjust)···································································11
Adjusting the Sound (Audio Adjust)············································· 11
Other Information
Surround·······················································································17
Surround Modes and Parameters················································ 17
Unavailable Functions After Upgrading···················19
Specifications·········································································20
NOTE
When upgrading, the RS-232C connector cannot be used for the
DENON RF remote controller.
For details, see “Unavailable Functions After Upgrading” on page
19.
ENGLISH
Getting Started
Getting Started
Part Names and Functions
Connections
Remote Control Unit
Main Remote Control Unit (RC-1118)
qSPEAKERS button····························································································· (12, 15)
Front Height
Function when the button is
pressed
STANDARD
Audyssey DSX ON/OFF
(vpage 15)
DSP SIMULATION
Front Height ON/OFF
(vpage 12)
DIRECT/STEREO
No function
STANDARD
Audyssey DSX ON/OFF
(vpage 15)
DSP SIMULATION
Front Wide ON/OFF
(vpage 12)
DIRECT/STEREO
No function
Unavailable Functions After Upgrading
Front Wide
Surround Mode
(vpage 69 of GThe original
versionH Operating Instructions)
Information
Amp Assign
(vpage 8)
Playback
Rear
Settings
When upgrading, the function of the button shown below is modified.
For the other buttons, refer to page 7 of GThe original versionH Operating Instructions.
q
Specifications
ENGLISH
Getting Started
Connections
Installing / Setting the Speakers
Connections
Audyssey DSX™ is a function to reproduce sound with deeper and more spacious surround space.
To use Audyssey DSX, install front wide or front height speakers.
Settings
a Determine the Speaker Layout
Installing All the Speakers
n When 7.1ch (Front Height Speaker) Connected
Playback
Information
Front height speakers
Front height speakers
Front speakers
Front speakers
Center speaker
Front wide
speaker
Subwoofer
z2
z1
Center speaker
Monitor
z
Point slightly
downwards
3
Front height
speaker
Front speaker
Surround speaker
2 to 3 feet /
60 to 90 cm
Surround speakers
Surround speaker
Surround back speakers
Surround speaker
GAs seen from aboveH
GAs seen from the sideH
n When 7.1ch (Front Wide Speaker) Connected
NOTE
Front wide speakers
Front speakers
Center speaker
Monitor
Subwoofer
3
Specifications
It is not possible to use the surround back speakers, front height speakers and front wide speakers
simultaneously.
z
Unavailable Functions After Upgrading
Subwoofer
Front wide
speaker
z1:22˚ ~ 30˚
z2:22˚ ~ 45˚
z3:90˚ ~ 110˚
z
2
z1
z1:22 ~ 30˚
z2:55 ~ 60˚
z3:90 ~ 110˚
Surround speaker
Front speaker
Front wide
speaker
2 to 3 feet /
60 to 90 cm
Surround speakers
GAs seen from aboveH
GAs seen from the sideH
ENGLISH
Speaker Connections
s Set the “Amp Assign” Mode According to the Speaker
Layout
Front
speakers A
Center
speaker
Surround
speakers
Front Height
Speakers
(L)
w
(L)
(R)
q w
q
w
q
w
(R)
qw
(L)
w
q
(R)
q w
q
*/
Playback
Front Height
Example of speaker installation
(Number of channels played)
Settings
SURR. BACK /
AMP ASSIGN
Speaker connections
Subwoofer
with built-in
amplifier
Connections
Amp assign
mode
(vpage 8)
Front
speakers B
Subwoofer
The signals output from the AVR-3310CI’s SURR. BACK/AMP ASSIGN speaker terminals can be switched
(vpage 8 “Amp Assign”).
Getting Started
Installing / Setting the Speakers
Front Wide
Speakers
Unavailable Functions After Upgrading
Front Wide
Information
(7.1)
(7.1)
(L)
w
(R)
q w
q
Specifications
Surround back /
Front height /
Front wide speakers
For connections of the SURR. BACK/AMP ASSIGN speaker terminals, see “Set the “Amp Assign”
Mode According to the Speaker Layout” (vpage 4).
ENGLISH
Getting Started
Settings
GUI Menu Map
indicates functions modified by upgrading.
Connections
Pressing MENU displays the GUI menu. From this menu, you can
move to various setting screens.
Setting items
Settings
Audio / Video Adjust
Adjust various audio and
video parameters.
Information
Show information about
receiver settings, input
signals, etc.
Detailed items
Playback
Information
Unavailable Functions After Upgrading
Adjust various audio parameters.
Picture Adjust
Status
Audio Input Signal
HDMI Information
Auto Surround Mode
Adjust various video parameters.
Shows information about current settings.
Shows information about audio input signals.
Shows information about HDMI input/output signals and monitor.
Shows information about settings stored for the auto surround
mode.
Shows information about settings stored for the Quick Select
function.
Shows information about preset channels.
Makes the optimum settings for the speakers being used
automatically.
Check Audyssey Auto Setup measurement results.
This item is only displayed after Audyssey Auto Setup procedure has
been performed.
Quick Select
Items that only need to be set once
Set these for example upon purchase.
Once these items are set, there is no need to
set them again unless the speaker layout or the
connected speakers have been changed.
Specifications
MENU
Front
uto Setup
A
Makes the optimum
speaker settings and
corrects for the acoustic
characteristics of the
room.
Manual Setup
Use this to make
various types of detailed
settings.
Input Setup
Use this to make
settings
related
to
playing input sources.
Description
Audio Adjust
Preset Channel
Audyssey™ Auto Setup
Parameter Check
Speaker Setup
HDMI Setup
Audio Setup
Network Setup
Zone Setup
Option Setup
Auto Preset
Preset Skip
Preset Name
Parental Lock
Antenna Aiming
Input Assign
Video
Input Mode
Rename
Source Level
Playback Mode (for iPod)
Playback Mode (for NET/USB)
Still Picture
Sets the speaker size and distance, the channel level, etc.
Make settings for HDMI video/audio output.
Make settings for audio playback.
Make network settings.
Make settings for audio playback in the multi-zone system.
Make various other settings.
Use the auto preset function to program radio stations.
Set the preset memories that you do not want to display when tuning.
Assign name to a preset memory.
Set the Parental Lock.
Adjust the SIRIUS reception sensitivity.
Change input connector assignment.
Makes the video settings.
Sets the audio input mode and decode mode.
Change the display name for this source.
Adjust the playback level of the audio input.
Make settings for “iPod” playback.
Make settings for “NET/USB” playback.
Make settings for still picture playback.
Page
11
6
8
19
ENGLISH
The acoustic characteristics of the connected speakers and
listening room are measured and the optimum settings are made
automatically.
When upgrading, contents of “Amp Assign” are modified.
n Set the channel to be measured (Channel Select)
dPerform Audyssey Auto Setup
GExample qH
FHL
FL
SW
C
FR
GExample wH
FHR
FHL
FL
SW
C
FR
FHR
C
GExample wH
FR
FWL
FL
FWR
SW
C
FR
FWL
FWR
( : Measuring positions)
*M
*M
SL
SR
FL : Front speaker (L)
FR : Front speaker (R)
FHL : Front height speaker (L)
FHR : Front height speaker (R)
FWL : Front wide speaker (L)
FWR : Front wide speaker (R)
SL
SR
C : Center speaker
SW : Subwoofer
SL : Surround speaker (L)
SR : Surround speaker (R)
SBL : Surround back speaker (L)
SBR : Surround back speaker (R)
The main listening position refers to the most central position where
one would normally sit within the listening environment.
MultEQ® uses the measurements from this position to calculate
speaker distance, level, polarity, and the optimum crossover value
for the subwoofer.
*M
*M
SR
SL
Specifications
SL
SW
About the main listening position (*M)
( : Measuring positions)
Check the Measuring Results and Equalizer
Type after Audyssey Auto Setup
(Parameter Check)
GExample qH
FL
Unavailable Functions After Upgrading
n When using Front Height Speakers
Information
n Change the Amplifier Assignment
(Amp Assign) (vpage 7)
n When Using the Front Wide Speakers
Playback
sAudyssey Auto Setup Preparations
Audyssey MultEQ® automatically measures the acoustical problems
in the listening environment to create the best audio experience for
your home theater.
•When Audyssey™ Auto Setup procedure is performed, the MultEQ®,
Dynamic EQ® and Dynamic Volume™ functions (vpage 13 ~15)
are enabled.
•Use the included setup microphone (DM-A409) to perform Audyssey
Auto Setup procedure.
•Measurements are performed by placing the calibrated microphone
successively at multiple positions throughout the listening area as
shown in GExample qH. For best results, it is strongly recommended
to measure 6 positions so that the measurements have the proper
spatial weighting.
Even if the listening environment is small as shown in GExample wH,
measuring at multiple points throughout the listening environment
results in more effective correction.
Settings
aConnect the Included Setup Microphone
Important Information
Connections
n Audyssey Auto Setup Flow
Getting Started
Make the Optimal Speaker Settings, and Correct the Room Acoustics
(Audyssey™ Auto Setup)
SR
See overleaf
ENGLISH
Getting Started
Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey™ Auto Setup)
NOTE
Connections
Settings
Playback
Information
•Loud test sounds may be played during Audyssey MultEQ®
automatic speaker setup. This is part of normal operation. If there
is background noise in room, these test signals will increase in
volume.
•Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
•Make the room as quiet as possible. Background noise can disrupt
the room measurements. Close windows, silence cell phones,
televisions, radios, air conditioners, fluorescent lights, home
appliances, light dimmers, or other devices as measurements may
be affected by these sounds.
Cell phones should be placed away from all audio electronics during
the measurement process as Radio Frequency Interference (RFI)
may cause measurement disruptions (even if the cell phone is not in
use).
• Operating MASTER VOLUME during the measurements will cancel
the measurements.
o p to select Amp Assign Mode, then press
2 Press
RETURN.
a Connect the Included Setup
Microphone
vpage 29 of GThe original versionH Operating Instructions
s Audyssey Auto Setup Preparations
around items indicate the default setting.
STEP1 Preparation
Perform the following settings if adjustments, etc., are required for
the speaker environment you’re using.
If you do not need to perform the following settings, or have already
completed them, select “Auto Setup Start” and then press ENTER.
Proceed to “ STEP2 ”.
Change the Amplifier Assignment (Amp Assign)
Unavailable Functions After Upgrading
The signal output from the SURR.BACK/AMP ASSIGN speaker
terminal of the AVR-3310CI can be switched to match your speaker
environment (vpage 8 “Amp Assign”).
1
Press ui to select
“Amp Assign”, then
press ENTER.
Normal
: The surround back channel audio signals are
output.
ZONE2
: The ZONE2 audio signals are output.
ZONE3
: The ZONE3 audio signals are output.
ZONE2/3-MONO : The ZONE2 / ZONE3 monaural audio signals are
output.
Front A Bi-Amp
: The bi-amp audio signals are output. Set this for
bi-amp playback of the front A speakers.
Front B Bi-Amp
: The bi-amp audio signals are output. Set this for
bi-amp playback of the front B speakers.
Front Height
: The front height channel audio signals are output.
Front Wide
: The front wide channel audio signals are output.
indicates functions added by upgrading.
• When you are using surround back speakers with ZONE2/ZONE3,
set to “ZONE2” or “ZONE3”.
• You can set in the same way as described in “Amp Assign” on page
8.
NOTE
Since “Amp Assign” of AVR-3310CI is set to “ZONE2” by default,
audio is not output from the surround back speakers. When using the
surround back speakers with MAIN ZONE, change the “Amp Assign”
setting to “Normal”.
Set the channel to be measured (Channel Select)
Specifications
vpage 30 of GThe original versionH Operating Instructions
d Perform Audyssey Auto Setup
vpage 30 of GThe original versionH Operating Instructions
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting
:Return to previous menu
ENGLISH
For details on how to select, set and cancel settings for each menu, see “GUI Menu
Operation” (vpage 26 of GThe original versionH Operating Instructions).
Setting contents
NOTE
Perform when setting the speakers manually or when changing settings made in Audyssey Auto Setup.
Sets the signal output to the
speaker connected to the
SURR. BACK/AMP ASSIGN
terminals.
Setting contents
Normal : The surround back channel audio signals are output.
ZONE2 : The ZONE2 audio signals are output.
ZONE3 : The ZONE3 audio signals are output.
ZONE2/3-MONO : The ZONE2 / ZONE3 monaural audio signals are
output.
Front A Bi-Amp : The bi-amp audio signals are output. Set this for bi-amp
playback of the front A speakers.
Front B Bi-Amp : The bi-amp audio signals are output. Set this for bi-amp
playback of the front B speakers.
Front Height : The front height channel audio signals are output.
Front Wide : The front wide channel audio signals are output.
When “Front” is set to “Small”, “Subwoofer” can automatically set
to “Yes”.
Surround : Set the presence and size of the surround speakers.
• Large : Use of a large speaker that can adequately playback low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround speakers are not connected.
• When “Surround” is set to “Large”, “Surround Back”, “Front Height”
and “Front Wide“ can be set to “Large”.
• When “Surround” is set to “None”, “Surround Back”, “Front Height”
and “Front Wide” can automatically set to “None”.
See overleaf
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting
:Return to previous menu
Specifications
Since “Amp Assign” of AVR-3310CI is set to “ZONE2” by default,
audio is not output from the surround back speakers. When using the
surround back speakers with MAIN ZONE, change the “Amp Assign”
setting to “Normal”.
“Large” is not displayed when “Front” is set to “Small”.
Subwoofer : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
Unavailable Functions After Upgrading
Setting items
Amp Assign
Information
Default settings are underlined.
Playback
Making the Speaker Settings (Speaker Setup)
• When “Subwoofer” is set to “No”, “Front” can automatically set to
“Large”.
• When “Front” is set to “Small”, “Center”, “Surround”, “Surround
Back”, “Front Height” and “Front Wide“ can not be set to “Large”.
Center : Set the presence and size of the center speaker.
• Large : Use of a large speaker that can adequately playback low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when a center speaker is not connected.
Settings
When upgrading, contents of “Speaker Setup” are modified.
For setting “Speaker Setup”, make settings by referring to this manual
but not GThe original versionH Operating Instructions.
elect “Large” or “Small”
S
not according to the
physical size of the speaker
but according to the low
frequency reproduction
capabilities based on the
frequency set at “Crossover
Frequency” (vpage 10).
Connections
Front : Set the front speaker size.
Select speaker configuration • Large : Use of a large speaker that can adequately playback low
frequencies.
and size (bass reproduction
• Small : Use of a small speaker that has inadequate playback capacity for
capability).
low frequencies.
Getting Started
Setting items
Speaker Configuration
Making Detailed Settings
(Manual Setup)
ENGLISH
Getting Started
Making Detailed Settings (Manual Setup)
Setting items
Speaker Configuration
(Continued)
Setting contents
Connections
Surround Back : Set the presence, size and number of surround back
speakers.
• Large : Use of a large speaker that can adequately playback low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround back speakers are not connected.
Setting items
Bass Setting
Setting contents
Settings for subwoofer and
LFE signal range playback.
Settings
• 2spkrs : Use two surround back speakers.
• 1spkr : Use only one surround back speaker. When you select this
setting, connect the surround back speaker to the left (L) channel.
Playback
Information
• When the “Amp Assign” setting (vpage 8) is other than “Normal”,
you cannot make the “Surround Back” setting.
• Even when the Surround Back Speaker setting is other than “None”,
sound may not be emitted from the surround back speaker, depending
on the playback source. In this case, “Surround Parameters” – “Surround
Back” setting other than “OFF” (vpage 12).
Front Height : Set the presence and size of the front height speakers.
• Large : Use of a large speaker that can adequately playback low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the front height speakers are not connected.
Distance
Unavailable Functions After Upgrading
Set distance from listening
position to speakers.
Measure beforehand the
distance from the listening
position to each speaker.
When the “Amp Assign” setting (vpage 8) is other than “Front
Height”, you cannot make the “Front Height” setting.
Front Wide : Set the presence and size of the front wide speakers.
• Large : Use of a large speaker that can adequately playback low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the front wide speakers are not connected.
Specifications
When the “Amp Assign” setting (vpage 8) is other than “Front
Wide”, you cannot make the “Front Wide” setting.
Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
• LFE : The low range signal of the channel set to “Small” speaker size is
added to the LFE signal output from the subwoofer.
• LFE+Main : The low range signal of all channels is added to the LFE
signal output from the subwoofer.
• This can be set when “Speaker Configuration” – “Subwoofer” (vpage
8) is set to “Yes”.
• Play music or a movie source and select the mode offering the strongest
bass.
• Select “LFE+Main” if you want the bass signals to always be produced
from the subwoofer.
LPF for LFE : Set LFE signal playback range.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz
Unit : Set the unit of distance.
• Feet
• Meters
Step : Set the minimum variable width of the distance.
• 1ft / 0.1ft
• 0.1m / 0.01m
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
S. Back Lz / S. Back Rz / Front Height L / Front Height R / Front Wide
L / Front Wide R : Select the speaker.
z: When the “Speaker Configuration” – “Surround Back” setting
(vpage 9) is set to “1spkr”, “S. Back” is displayed.
• 0.0ft ~ 60.0ft / 0.00m ~ 18.00m : Set the distance.
• Speakers set to “None” in “Speaker Configuration” (vpage 8) are not
displayed.
• The speakers that can be selected differ depending on the “Amp Assign”
(vpage 8) and “Speaker Configuration” (vpage 8) settings.
• Default settings :
Front / Center / Subwoofer / Front Height / Front Wide : 12.0 ft (3.60 m)
Surround / Surround Back : 10.0 ft (3.00 m)
• Set the difference in the distance between the speakers to less than 20
feet (6.0 meters).
Default : Reset all distance settings to factory default.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select “Default” and press ENTER, the “Default Setting?”
prompt is displayed. Select either “Yes” or “No”, and press ENTER.
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting
:Return to previous menu
ENGLISH
Setting items
Channel Level
Setting contents
Setting items
Front Speaker Setup
Set the front speakers to
use for every surround
mode.
• –12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.
MULTI CH : The front speakers used in modes other than the direct,
stereo and pure direct play modes (2 channel) are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
Unavailable Functions After Upgrading
Advanced : Specify crossover frequency for each speaker.
• Front / Center / Surround / Surround Back / Front Height / Front
Wide : Select the speaker.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz /150Hz / 200Hz /
250Hz : Set the crossover frequency.
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
Specifications
• Can be set when the “Speaker Configuration” – “Subwoofer” (vpage
8) setting is “Yes”, or when you have a speaker that is set to “Small”.
• Always set the crossover frequency to “80 Hz”. When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to “Small”, sound below the crossover frequency is cut
from the sound output. The cut bass sound is output from the subwoofer
or front speakers.
• The speakers that can be set when “Advanced” is selected differ
according to the “Subwoofer Mode” setting (vpage 9).
• When “LFE” is selected, speakers set to “Small” at “Speaker
Configuration” can be set. If the speakers are set to “Large”, “Full
Band” is displayed and the setting cannot be made.
• If set to “LFE+Main”, this setting can be made regardless of the
speaker size.
Main remote control
operation buttons
Information
NOTE
•When set to “Custom”, <FRONT SPEAKERS> does not operate.
•The front speaker setting stored for the “Quick Select” function is given
priority.
Playback
Outputs at below set
frequency, each speaker’s
bass signal output from
the subwoofer. Set this
according to the low
frequency reproduction
capabilities of the speakers
you are using.
2CH DIRECT/STEREO : The front speakers used in the direct, stereo and
pure direct play modes (2 channel) are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
Settings
Crossover Frequency
• Speakers set to “None” in the “Speaker Configuration” (vpage 8)
settings are not displayed.
• When o is pressed while the subwoofer volume is set to “–12 dB”, the
“Subwoofer” setting switches to “OFF”.
• When a headphones jack is inserted in the PHONES terminal of the AVR3310CI, the “Channel Level” is not displayed.
• You can also press [CHANNEL LEVEL] to set (vpage 79 of GThe
original versionH Operating Instructions “Adjust the Volume of the
Different Speakers“).
Default : Reset all channel level settings to factory default.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
Setting contents
Setting : Choose the method for setting the front speakers.
• Normal : The front speakers are set using the <FRONT SPEAKERS>.
• Custom : The front speakers used for the different playing modes are
set in advance.
Connections
Test Tone Start : Output test tone.
• Front L / Front Height L / Center / Front Height R / Front R / Front
Set the volume of the test
Wide R / Surround R / S. Back Rz / S. Back Lz / Surround L / Front
tone to be the same when it
is output from each speaker. Wide L / Subwoofer : Select the speaker.
z : When the “Speaker Configuration” – “Surround Back” setting
(vpage 9) is set to “1spkr”, “S. Back” is displayed.
Getting Started
Making Detailed Settings (Manual Setup)
:Confirm the setting
:Return to previous menu
10
ENGLISH
Getting Started
Playback
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Connections
For details on how to select, set and cancel settings for each menu, see “GUI Menu Operation” (vpage 26 of GThe original versionH Operating Instructions).
Settings
When upgrading, contents of “Audio Adjust” are modified.
For setting “Audio Adjust”, make settings by referring to this manual but
not GThe original versionH Operating Instructions.
Setting items
Surround Parameters
(Continued)
Playback
Adjusting the Sound (Audio Adjust)
Information
Default settings are underlined.
The sound being played in the surround mode can be adjusted to your liking.
The items (parameters) that can be adjusted depend on the signal being input and the currently set surround
mode. For details on the adjustable parameters, see “Surround Modes and Parameters” (vpage 17).
Unavailable Functions After Upgrading
Setting items
Surround Parameters
Adjust surround sound
parameters.
Setting contents
Mode : Set the play modes for the different surround modes.
n In the PLgx or PLg mode
Cinema : Surround sound mode optimized for movie sources.
Music : Surround sound mode optimized for music sources.
Game : Surround sound mode optimized for games.
Pro Logic : Dolby Pro Logic playback mode (PLg mode only).
n In the PLgz mode
Height : Dolby PLgz Height playback mode.
Specifications
n In the DTS NEO:6 mode
Cinema : Surround sound mode optimized for movie sources.
Music : Surround sound mode optimized for music sources.
• When “Surround Parameters” – “Front Height” (vpage 12) is set to
“ON”, the “Height” mode is set automatically.
• The “Music” mode is also effective for movie sources including a lot of
stereo music.
• The “Cinema” and “Music” modes can also be set by pressing [CINEMA]
or [MUSIC].
11
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
Setting contents
Cinema EQ : Soften the treble range of movie soundtracks for better
understanding.
• OFF : “Cinema EQ” is not used.
• ON : “Cinema EQ” is used.
DRC : Compress dynamic range (difference between loud and soft
sounds).w
• Auto : Automatic dynamic range compression on/off control according
to source. This can be set in the Dolby TrueHD mode.
• Low / Middle / High : These set the compression level.
• OFF : Dynamic range compression always off.
D.COMP : Compress dynamic range (difference between loud and soft
sounds).
• OFF : Turn dynamic range compression off.
• Low / Middle / High : These set the compression level.
LFE : Adjust the low-frequency effects level (LFE).
• –10dB ~ 0dB
For proper playback of the different sources, we recommend setting
to the values below.
• Dolby Digital sources : “0dB”
• DTS movie sources : “0dB”
• DTS music sources : “–10dB”
Center Image : Assign center channel signal to front left and right channels
for wider sound.
• 0.0 ~ 1.0 (0.3)
Panorama : Assign front L/R signal also to surround channels, for wider
sound.
• OFF : Do not set.
• ON : Set.
Dimension : Shift sound image center to front or rear, to adjust playback
balance.
• 0 ~ 6 (3)
Center Width : Assign center channel signal to front left and right channels
for wider sound.
• 0 ~ 7 (3)
:Confirm the setting
:Return to previous menu
ENGLISH
Setting items
Surround Parameters
(Continued)
Setting contents
Setting items
Surround Parameters
(Continued)
• “Front Wide” is not displayed with the settings listed below.
• When the ”Amp Assign” setting (vpage 8) is set to something other
than “Front Wide”
• When the “Speaker Configuration” – “Front Wide” setting (vpage
9) is set to “None”.
• “Front Wide” can be set by pressing [SPEAKERS] in DENON original
surround mode (DSP SIMULATION) (vpage 2).
n For multi-channel sources
Set the decoding method for the surround back channel.
DSCRT ON : Play the surround back signals included in the 7.1-channel
source.
MTRX ON : Generate and play the surround back signals from the
surround channel signals.
ES MTRXz1 : Generate and play the surround back signals from the
surround channel signals of the DTS source.
ES DSCRTz2 : Play the surround back signals included in the 6.1channel DTS source.
PLgx CINEMAz3 : Generate and play the surround back signals by
decoding the signals in the Dolby Pro Logic gx Cinema mode.
PLgx MUSIC : Generate and play the surround back signals by decoding
the signals in the Dolby Pro Logic gx Music mode.
OFF : The surround back channel is not played.
z1 : This can be selected when playing DTS sources.
z2 : This can be selected when playing DTS sources including a signal
to identify discrete 6.1-channel signals.
z3 : This can be selected when “Speaker Configuration” – “Surround
Back” (vpage 9) is set to “2spkrs”.
See overleaf
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting
:Return to previous menu
12
Specifications
• “Front Height” is not displayed with the settings listed below.
• When the ”Amp Assign” setting (vpage 8) is set to something other
than “Front Height”
• When the “Speaker Configuration” – “Front Height” setting (vpage
9) is set to “None”
• “Front Height” cannot be set if the HD Audio source being played
includes a front height channel. In this case, the Front height channel is
played back without decoding in PLgz mode, using the input signal.
• “Front Height” can be set by pressing [SPEAKERS] in DENON original
surround mode (DSP SIMULATION) (vpage 2).
Front Wide : Set the front wide channel.
• ON : Use the front wide channel.
• OFF : Do not use the front wide channel.
Unavailable Functions After Upgrading
n For 2-channel sources
ON : The surround back channel is used.
OFF : No signal is played from the surround back channels.
Information
Front Height : Set the front height channel.
• ON : Use the front height channel.
• OFF : Do not use the front height channel.
• Some Dolby Digital EX sources do not include EX flags. If the playback
mode does not switch automatically even when “AFDM” is set to “ON”,
set “Surround Back” to “MTRX ON” or “PLgx CINEMA”.
• If the setting in “Speaker Configuration” – “Surround Back” (vpage 9)
is “None”, “Surround Back” is not displayed.
Surround Back : Sets the method of generating of the surround back
channel.
Playback
NOTE
“Room Size” does not indicate the size of the room in which sources are
played.
[Example] Playing Dolby Digital software (with EX flag)
• When “AFDM” is set to “ON”, the surround mode is automatically set
to the DOLBY D + PLgx C mode.
• To play in the DOLBY DIGITAL EX mode, set “AFDM” to “OFF” and
“Surround Back” to “MTRX ON”.
Settings
Set to a lower level if the positioning and sense of phase of the
surround signals seems unnatural.
Room Size : Determine size of acoustic environment.
• Small : Simulate acoustics of a small room.
• Medium small : Simulate acoustics of a medium-small room.
• Medium : Simulate acoustics of a medium room.
• Medium large : Simulate acoustics of a medium-large room.
• Large : Simulate acoustics of a large room.
Setting contents
AFDM (Auto flag detect mode) : Detects the source’s surround back
channel signal and sets the optimum surround mode automatically.
• OFF : Do not set.
• ON : Set.
Connections
Delay Time : Adjust delay time to control sound stage size.
• 0ms ~ 300ms (30ms)
Effect Level : Adjust effect signal level.
• 1 ~ 15 (10)
Getting Started
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
ENGLISH
Getting Started
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting items
Surround Parameters
(Continued)
Connections
Settings
Playback
Information
Unavailable Functions After Upgrading
Tone
Adjust the tonal quality of
the sound.
Setting contents
Setting items
Audyssey Settings
• This can also be set by pressing STANDARD.
• If the source being played contains a surround back signal, the decoder
type is automatically selected by the AFDM function. Set “AFDM” to
“OFF” to switch to your preferred decoder.
• If the setting in “Speaker Configuration” – “Surround Back” (vpage 9)
is “None”, “Surround Back” is not displayed.
Subwoofer Att. : Attenuate subwoofer level when using EXT. IN input.
• ON : Set.
• OFF : Do not set. Usually use in this mode.
Set this to “ON” if the subwoofer channel level seems too high when
playing audio signal.
Subwoofer : Turn subwoofer output on and off.
• ON : The subwoofer is used.
• OFF : The subwoofer is not used.
Default : Restores all the surround parameter settings to their defaults.
• No : Do not reset to the defaults.
• Yes : Reset to the defaults.
Tone Control : Sets the tone control function ON and OFF.
• ON : Allow tone adjustment (treble, bass).
• OFF : Playback without tone adjustment.
Setting contents
Set Audyssey MultEQ®,
Audyssey Dynamic EQ®
and Audyssey Dynamic
Volume™.
NOTE
If you have not performed
Auto Setup, or if you
change the speaker
settings after performing
Auto Setup, you may not
be able to select Dynamic
EQ/Dynamic Volume, and
“Run Audyssey” may be
displayed.
In this case, either perform
Audyssey Auto Setup over
again or perform “Restore”
(vpage 33 of GThe
original versionH Operating
Instructions) to return to
the settings after Audyssey
Auto Setup was run.
• This can be set when “Dynamic EQ” (vpage 14) is set to “OFF”.
• The tone cannot be adjusted in the direct mode.
Bass : Adjust low frequency range (bass).
• –6dB ~ +6dB
This can be set when “Tone Control” (vpage 13) is set to “ON”.
MultEQ : Corrects both time and frequency response problems in the
listening area.
• Audyssey : Optimize the frequency response of all speakers.
• Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
• Audyssey Flat : Optimize frequency response of all speakers to flat
response.
• Manual : Apply frequency response set with “Manual EQ” (vpage
16).
• OFF : Turn “MultEQ” equalizer off.
• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
selected after Audyssey Auto Setup has been performed. “Audyssey”
is automatically selected after performing Audyssey Auto Setup. “When
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected, “
”
lights.
• After running Audyssey Auto Setup, if the Speaker Configuration,
Distance, Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only “
” lights.
• If “Dynamic EQ” or “Dynamic Volume” is set to “ON” when “MultEQ”
is set to either “OFF” or “Manual”, “MultEQ” is automatically set to
“Audyssey”.
• You can also press MULTEQ to set.
NOTE
• “MultEQ” and “Manual EQ” cannot be selected when “EQ Customize”
is set to “Not Used” (vpage 38 of GThe original versionH Operating
Instructions).
• When using headphones, “MultEQ” is set to “OFF”.
Treble : Adjust high frequency range (treble).
• –6dB ~ +6dB
Specifications
This can be set when “Tone Control” (vpage 13) is set to “ON”.
13
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting
:Return to previous menu
ENGLISH
Setting items
Audyssey Settings
(Continued)
Setting contents
Setting items
Audyssey Settings
(Continued)
Dynamic EQ / Volume : OFF
“OFF”
“OFF”
About Dynamic EQ
Audyssey Dynamic EQ® solves the problem of deteriorating sound
quality as volume is decreased by taking into account human perception
and room acoustics. Audyssey Dynamic EQ works in tandem with
Audyssey MultEQ® to provide well-balanced sound for every listener at
any volume level.
• “
” is displayed when set to “ON”.
• When “MultEQ” is set to “OFF”, “Dynamic Volume” is automatically
set to “OFF”.
• You can also press DYNAMIC VOLUME to set.
Dynamic EQ / Volume : ON
Specifications
Operation on the main unit
Dynamic EQ : ON / Volume : OFF
“Green”
“Red”
Dynamic EQ / Volume : OFF
See overleaf
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting
:Return to previous menu
Unavailable Functions After Upgrading
“Red”
“Green”
etting is enabled when “Dynamic EQ” is “ON” (vpage 14).
S
Dynamic Volume : Solves the problem of large variations in volume level
between TV, movies and other content (between quiet passages and loud
passages, etc.) by automatically adjusting to the user’s preferred volume
setting.
• ON : Use the “Dynamic Volume” equalizer. The Dynamic Volume effect
will be at the level of the “Setting” (vpage 15).
• OFF : Do not use the “Dynamic Volume” equalizer.
Information
Dynamic EQ : ON/Volume : OFF
Playback
• When “MultEQ” is set to “OFF” or “Manual”, “Dynamic EQ” is
automatically set to “OFF”.
• If “Dynamic Volume” is set to “ON”, “Dynamic EQ” is automatically
set to “ON”.
• When you set ”Dynamic EQ” to ”ON”, “Tone Control” is switched
”OFF”.
• You can also press [DYNAMIC EQ] to set.
Settings
• After performing “Audyssey Auto Setup”, the “Dynamic EQ” setting
automatically becomes “ON”.
• “
” is displayed when set to “ON”.
Setting contents
Reference Level Offset : Audyssey Dynamic EQ® is referenced to the
standard film mix level. It makes adjustments to maintain the reference
response and surround envelopment when the volume is turned down
from 0 dB. However, film reference level is not always used in music or
other non-film content. The Dynamic EQ Reference Level Offset provides
three offsets from the film level reference (5 dB, 10 dB, and 15 dB) that can
be selected when the mix level of the content is not within the standard.
• 0dB (Film Ref) : This is the default setting and should be used when
listening to movies.
• 5dB : Select this setting for content that has a very wide dynamic range,
such as classical music.
• 10dB : Select this setting for jazz or other music that has a wider dynamic
range. This setting should also be selected for TV content as that is
usually mixed at 10 dB below film reference.
• 15dB : Select this setting for pop/rock music or other program material
that is mixed at very high listening levels and has a compressed dynamic
range.
Connections
Dynamic EQ : Solves the problem of deteriorating sound quality as
volume is decreased by taking into account human perception and room
acoustics.
• ON : Use the Dynamic EQ equalizer.
• OFF : Do not use the Dynamic EQ equalizer.
Getting Started
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
14
ENGLISH
Getting Started
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting items
Audyssey Settings
Setting contents
Setting items
DSX Soundstage
Operation on the main remote control unit
(Continued)
Dynamic EQ / Volume : ON
Dynamic EQ : ON / Volume : OFF
Connections
“Green”
“Green”
Adjust Audyssey DSX™
setting and sound stage
parameters.
“Red”
Setting contents
Audyssey DSX : Provides more immersive surround sound by adding the
new channels.
• ON : Set Audyssey DSX to expand surround.
• OFF : Do not set Audyssey DSX.
Stage Width : Adjust sound stage width when using front wide speakers.
• –10 ~ 0
Stage Height : Adjust sound stage height when using front height speakers.
• –10 ~ 0
Settings
About Dynamic Volume
Playback
Audyssey Dynamic Volume™ solves the problem of large variations in
volume level between television programs, commercials, and between
the soft and loud passages of movies.
Audyssey Dynamic EQ® is integrated into Dynamic Volume so that
as the playback volume is adjusted automatically, the perceived bass
response, tonal balance, surround impression, and dialog clarity remain
the same.
Information
Unavailable Functions After Upgrading
Setting : Set “Dynamic Volume” equalizer effect.
• Midnight : High setting affects volume the most, causing all sounds to
be of equal loudness.
• Evening : Middle setting prevents loud and soft sounds from being
much louder and softer respectively than average sounds.
• Day : Low setting provides the least adjustments to the loudest and
softest of sounds.
Can be set when “Dynamic Volume” is set to “ON”.
• “Audyssey DSX” can be set when you are using front height speakers
or front wide speakers.
• “Audyssey DSX” is only valid when using a center speaker.
• “Audyssey DSX” is valid when surround mode is STANDARD mode
other than PLgz Height.
• “Audyssey DSX” can be operated by [SPEAKERS].
• “DSX Soundstage” cannot be configured if the HD Audio source being
played includes Front height and Front wide channels. In this case, the
respective channels are played back using the input signals.
About Audyssey Dynamic Surround Expansion (DSX)
Audyssey DSX™ is a scalable surround expansion system that adds
new channels to improve the surround impression. Based on research
in human hearing Audyssey DSX adds a pair of Wide channels in the
front because that information is critical in the rendering of a realistic
soundstage.
Audyssey DSX then adds a pair of Height channels above the main
front channels to reproduce the next most important acoustical and
perceptual cues related to soundstage depth. In addition to creating
these new channels, Audyssey DSX applies Surround Envelopment
Processing to enhance the blend between the front and side/back
surround channels. The result is a much more seamless and enveloping
home theater experience.
Specifications
15
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting
:Return to previous menu
ENGLISH
Setting items
Manual EQ
Setting items
RESTORER
Audio Delay
0ms ~ 200ms
While viewing video,
manually adjust the time to
delay audio output.
“Base Curve Copy” is displayed after Audyssey Auto Setup procedure
has been performed.
Unavailable Functions After Upgrading
Default : Reset the settings to the default values.
• Yes : Reset.
• No : Do not Reset.
OFF : Do not use RESTORER.
RESTORER
Mode 1 (RESTORER 64) : Optimized mode for compressed sources with
This function restores
very weak highs.
compressed audio signals
Mode 2 (RESTORER 96) : Apply suitable bass and treble boost for all
to how they were before
compression and corrects the compressed sources.
sense of volume of the bass Mode 3 (RESTORER HQ) : Optimized mode for compressed sources with
normal highs.
and treble to obtain richer
playback sound.
• This can be set within the range of 0 to 100 ms when “Auto Lip
Sync” is set to “ON” and when a TV compatible with Auto Lipsync is
connected.
• Store “Audio Delay” for each input source.
• You can also press <AUDIO DELAY> to set.
Mode 1
(RESTORER 64)
Specifications
• This can be set with analog signals or when a PCM signal (fs = 44.1/48
kHz) is input.
• This cannot be set when the input mode is set to “EXT. IN” or when the
surround mode is set to “DIRECT”.
• The default setting for “iPod” and “NET/USB” are “Mode 3”. All others
are set to “OFF”.
• When set to something other than “OFF”, “
” is displayed.
• This can also be set by pressing RESTORER during playback.
OFF
Mode 2
(RESTORER 96)
Mode 3
(RESTORER HQ)
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
Information
Can be set when the “MultEQ” setting (vpage 13) is “Manual”.
Base Curve Copy : Copy “Audyssey Flat” curve from MultEQ.
Yes : Copy.
No : Do not copy.
About the RESTORER function
•Such compressed audio formats as MP3, WMA (Windows Media Audio)
and MPEG-4 AAC reduce the amount of data by eliminating signal
components that are hard for the human ear to hear. The RESTORER
function generates the signals eliminated upon compression, restoring
the sound to conditions near those of the original sound before
compression. It also corrects the sense of volume of the bass to obtain
richer sound with compressed audio signals.
•This is displayed on the GUI menu and can be set when the input source
is set to “HD Radio” or “NET/USB”, or when analog signals (including
FM/AM signals) or PCM signals (fs = 44.1/48 kHz) are input.
Playback
(Continued)
Settings
q Select the speaker tone adjustment method.
All : Adjust the tone of all speakers together.
L/R : Adjust the tone of left and right speakers together.
Each : Adjust the tone of each speaker.
w Select the speaker.
e Select the adjustment frequency band.
63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz / 16kHz
b Select the speakers you want to adjust when “L/R” or “Each” is
selected.
r Adjust the level.
–20.0dB ~ +6.0dB (0.0dB)
Setting contents
Connections
Use the graphic equalizer
to adjust the tone of each
speaker.
Setting contents
Adjust CH : Correct the tone of each speaker.
Getting Started
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
:Confirm the setting
:Return to previous menu
16
ENGLISH
Getting Started
Other Information
Connections
Surround Modes and Parameters
Surround
Signals and adjustability in the different modes
Surround Mode
Channel output
Settings
Front L/R
Center
Surround
L/R
Surround
Back L/R
Parameter (default values are shown in parentheses)
Su­b­­­­woofer
Front Wide
L/R
Front Height
L/R
D. COMP
z1
DRC
LFE
z2
AFDM
z3
z1
Surround
Back
Cinema EQ.
Mode
Room Size
Effect Level
Playback
Information
Unavailable Functions After Upgrading
Specifications
PURE DIRECT, DIRECT (2ch)
S
A
A
A
Dz4
A
A
S (OFF)
S (Auto)
S (0 dB)
A
A
A
A
A
A
MULTI CH DIRECT
S
D
D
D
D
A
A
A
A
S (0 dB)
S (ON)
S
A
A
A
A
STEREO
S
A
A
A
D
A
A
S (OFF)
S (Auto)
S (0 dB)
A
A
A
A
A
A
EXT. IN
S
D
D
D
D
A
A
A
A
A
A
A
A
A
A
A
MULTI CH IN
S
D
D
D
D
D (NOTE4)
D (NOTE4)
A
A
S (0 dB)
S (ON)
S
S (OFF)
A
A
A
DOLBY PRO LOGIC gz
S
D
D
A
D
A
D
S (OFF)
S (Auto)
S (0 dB)
A
A
S (OFF)
S (Height)
A
A
DOLBY PRO LOGIC gx
S
D
D
D
D
A
A
S (OFF)
S (Auto)
A
A
S
S (NOTE1)
S (Cinema)
A
A
DOLBY PRO LOGIC g
S
D
D
A
D
D (NOTE4)
D (NOTE4)
S (OFF)
S (Auto)
A
A
S
S (NOTE2)
S (Cinema)
A
A
DTS NEO:6
S
D
D
D
D
D (NOTE4)
D (NOTE4)
S (OFF)
S (Auto)
A
A
S
S (NOTE1)
S (Cinema)
A
A
DOLBY DIGITAL
S
D
D
D
D
D (NOTE4)
D (NOTE3)
S (OFF)
A
S (0 dB)
S (ON)
S
S (OFF)
A
A
A
DOLBY DIGITAL Plus
S
D
D
D
D
D (NOTE4)
D (NOTE3)
S (OFF)
A
S (0 dB)
S (ON)
S
S (OFF)
A
A
A
DOLBY TrueHD
S
D
D
D
D
D (NOTE4)
D (NOTE3)
A
S (Auto)
S (0 dB)
S (ON)
S
S (OFF)
A
A
A
DTS SURROUND
S
D
D
D
D
D (NOTE4)
D (NOTE3)
S (OFF)
A
S (0 dB)
S (ON)
S
S (OFF)
A
A
A
DTS 96/24
S
D
D
D
D
D (NOTE4)
D (NOTE3)
S (OFF)
A
S (0 dB)
S (ON)
S
S (OFF)
A
A
A
DTS-HD
S
D
D
D
D
D (NOTE4)
D (NOTE3)
S (OFF)
A
S (0 dB)
S (ON)
S
S (OFF)
A
A
A
DTS EXPRESS
S
D
D
D
D
D (NOTE4)
D (NOTE3)
S (OFF)
A
S (0 dB)
S (ON)
S
S (OFF)
A
A
A
5CH/7CH STEREO
S
D
D
D
D
D (NOTE6)
D (NOTE5)
S (OFF)
A
S (0 dB)
A
S
A
A
A
A
ROCK ARENA
S
D
D
D
D
D (NOTE6)
D (NOTE5)
S (OFF)
A
S (0 dB)
A
S
A
A
S (Medium)
S (10)
JAZZ CLUB
S
D
D
D
D
D (NOTE6)
D (NOTE5)
S (OFF)
A
S (0 dB)
A
S
A
A
S (Medium)
S (10)
MONO MOVIE
S
D
D
D
D
D (NOTE6)
D (NOTE5)
S (OFF)
A
S (0 dB)
A
S
A
A
S (Medium)
S (10)
VIDEO GAME
S
D
D
D
D
D (NOTE6)
D (NOTE5)
S (OFF)
A
S (0 dB)
A
S
A
A
S (Medium)
S (10)
MATRIX
S
D
D
D
D
D (NOTE6)
D (NOTE5)
S (OFF)
A
S (0 dB)
A
S
A
A
A
A
VIRTUAL
S
A
A
A
D
A
A
S (OFF)
A
S (0 dB)
A
A
A
A
A
A
S: Signal / Adjustable
A : No signal / Not adjustable
D: Turned on or off by speaker configuration setting
NOTE1 :This parameter is availabe when the “Mode” is set to “Cinema” (vpage 11).
NOTE2 :This parameter is availabe when the “Mode” is set to “Cinema” or “Pro Logic” (vpage 11).
NOTE3 :This parameter is availabe when the “Front Height” is set to “ON” or “Audyssey DSX” is set to “ON”(vpage 12, 15).
NOTE4 :This parameter is availabe when the “Audyssey DSX” is set to “ON” (vpage 15).
NOTE5 :This parameter is availabe when the “Front Height” is set to “ON” (vpage 12).
NOTE6 :This parameter is availabe when the “Front Wide” is set to “ON” (vpage 12).
NOTE:
z1 :When playing Dolby Digital and DTS signals.
z2 :When playing Dolby TrueHD signal.
z3 :When playing Dolby Digital, DTS and DVD-Audio.
z4 :When the “Subwoofer Mode” is set to “LFE+Main” (vpage 9) only.
17
ENGLISH
Signals and adjustability in the different modes
Parameter (default values are shown in parentheses)
Surround Mode
Delay Time
Subwoofer
Front
Height
Front
Wide
PRO LOGIC g/gx MUSIC mode only
NEO:6 MUSIC
mode only
EXT. IN only
Dimension
Center Width
Center Image
Subwoofer Att.
MultEQ
Dynamic
EQ
(NOTE9)
Dynamic
Volume
(NOTE10)
RESTORER
(NOTE11)
Audyssey DSX
A
A
A
A
A
A
A
A
A
A
A
A
S
A
A
A
A
A
A
A
A
A
A
A
A
STEREO
A
A
A
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
S
A
EXT. IN
A
A
A
A
A
A
A
A
S
A
A
A
A
A
A
MULTI CH IN
A
A
S
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
A
S
DOLBY PRO LOGIC gz
A
A
S
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
S
A
DOLBY PRO LOGIC gx
A
A
S
A
S (OFF)
S (3)
S (3)
A
A
S (OFF)
S (OFF)
S
S
S
A
DOLBY PRO LOGIC g
A
A
S
A
S (OFF)
S (3)
S (3)
A
A
S (OFF)
S (OFF)
S
S
S
S
DTS NEO:6
A
A
A
A
A
A
A
S (0.3)
A
S (OFF)
S (OFF)
S
S
S
S
DOLBY DIGITAL
A
A
S
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
A
S
DOLBY DIGITAL Plus
A
A
S
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
A
S
DOLBY TrueHD
A
A
S
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
A
S
DTS SURROUND
A
A
S
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
A
S
DTS 96/24
A
A
S
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
A
S
DTS-HD
A
A
S
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
A
S
DTS EXPRESS
A
A
S
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
A
S
5CH/7CH STEREO
A
A
S
S
A
A
A
A
A
S (OFF)
S (OFF)
S
S
S
A
ROCK ARENA
A
A
S
S
A
A
A
A
A
S (NOTE7)
S (OFF)
S
S
S
A
JAZZ CLUB
A
A
S
S
A
A
A
A
A
S (OFF)
S (OFF)
S
S
S
A
MONO MOVIE
A
A
S
S
A
A
A
A
A
S (OFF)
S (OFF)
S
S
S
A
VIDEO GAME
A
A
S
S
A
A
A
A
A
S (OFF)
S (OFF)
S
S
S
A
MATRIX
S (30 ms)
A
S
S
A
A
A
A
A
S (OFF)
S (OFF)
S
S
S
A
VIRTUAL
A
A
A
A
A
A
A
A
A
S (OFF)
S (OFF)
S
S
S
A
Unavailable Functions After Upgrading
A
A
Information
S
A
Playback
A
Settings
PURE DIRECT, DIRECT (2ch)
MULTI CH DIRECT
Connections
Panorama
Tone Control
(NOTE8)
Getting Started
Surround
Specifications
S: Signal / Adjustable
A : No signal / Not adjustable
NOTE7 : BASS +6 dB, TREBLE +4 dB
NOTE8 : Cannot be set when the “Dynamic EQ” (vpage 14) setting is “ON”.
NOTE9 : Cannot be set when the “MultEQ” (vpage 13) setting is “OFF”.
NOTE10: Cannot be set when the “Dynamic EQ” (vpage 14) setting is “OFF”.
NOTE11: “RESTORER” can be set for analog or PCM 48 kHz or 44.1 kHz input signals.
18
ENGLISH
Getting Started
Unavailable Functions After Upgrading
When upgrading, the RS-232C connector cannot be used for the DENON RF remote controller.
Connections
Connecting Devices
Making Detailed Settings
(Manual Setup)
External Controller
vpage 22 of GThe original versionH Operating Instructions
Settings
n RS-232C connector
When you connect an external control device, you can control the AVR-3310CI
with the external control device. Perform the operation below beforehand.
Playback
qTurn on the AVR-3310CI’s power.
wTurn off the AVR-3310CI’s power from the external controller.
eCheck that the AVR-3310CI is in the standby mode.
OPTION
Making Other Settings (Option Setup)
vpage 43 of GThe original versionH Operating Instructions
When upgrading, this setting cannot be selected.
Information
Setting items
Setting contents
232C Port
Unavailable Functions After Upgrading
Serial Control : Set when using an external controller.
Set when using an external 2Way Remote : Set when using a 2-way remote control unit.
controller or two-way remote
When using a DENON two-way remote control (RC-7000CI or RCcontrol connected to the RS7001RCI, sold separately), set to “2Way Remote”.
232C terminal.
NOTE
When setting to “2Way Remote”, you can not use the RS-232C connector
as an external controller.
When upgrading, the DENON
RF remote controller cannot be
connected.
Specifications
Set as Necessary
Set this to use the RS-232C connector for the DENON RF remote controller.
“232C Port”
When using the AVR-3310CI in combination with the DENON RF remote controller (RC-7000CI, sold
separately) or RF remote receiver (RC-7001RCI, sold separately), two-way communication is enabled.
The AVR-3310CI’s status information as well as iPod and Internet audio music files can be browsed
watching the RF Remote Controller’s display. For details, refer to the operating instructions of the
respective devices.
NOTE
On the GUI menu, when setting “232C Port” to “2Way Remote”, you cannot use the RS-232C
connector as an external controller.
19
ENGLISH
nHD Radio section
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
PB / CB signal — 0.7 Vp-p, 75 Ω/ohms
PR / CR signal — 0.7 Vp-p, 75 Ω/ohms
5 Hz ~ 100 MHz — +0, –3 dB (when video convert set to “OFF”)
[FM]
(note: µV at 75 Ω/ohms, 0 dBf = 1 x 10-15 W)
87.5 MHz ~ 107.9 MHz
1.5 µV (14.8 dBf)
MONO 78 dB
STEREO 68 dB
HD
85 dB
MONO 0.1 %
STEREO 0.2 %
HD
0.02 %
[AM]
530 kHz ~ 1710 kHz
20 µV
85 dB
Unavailable Functions After Upgrading
Receiving Range:
Usable Sensitivity:
S/N (IHF-A):
Total harmonic Distortion (at 1 kHz):
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
C (color) signal — 0.286 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +0, –3 dB (when video convert set to “OFF”)
Information
1 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +0, –3 dB (when video convert set to “OFF”)
Playback
• Standard video connectors
Input / output level and impedance:
Frequency response:
• S-Video connectors
Input / output level and impedance:
Frequency response:
• Color component video connector
Input / output level and impedance:
Frequency response:
Settings
nVideo section
• Power amplifier
Front:
Rated output:
120 W + 120 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05 % T.H.D.)
160 W + 160 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Center:
120 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05 % T.H.D.)
160 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Surround:
120 W + 120 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05 % T.H.D.)
160 W + 160 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Surround back:
120 W + 120 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05 % T.H.D.)
160 W + 160 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Front height / Front wide:
120 W + 120 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05 % T.H.D.)
160 W + 160 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Dynamic power:
130 W x 2ch (8 Ω/ohms)
180 W x 2ch (4 Ω/ohms)
6 ~ 16 Ω/ohms
Output connectors:
Center, Surround, Surround back
6 ~ 16 Ω/ohms
Front:
A or B
8 ~ 16 Ω/ohms
A + B
• Analog
Input sensitivity / Input impedance: 200 mV / 12 kΩ/kohms (except for EXT. IN (SW, S, SB), CD, PHONO, V. AUX)
200 mV / 47 kΩ/kohms (EXT. IN (SW, S, SB), CD, PHONO, V. AUX)
Frequency response:
10 Hz ~ 100 kHz +1, –3 dB (DIRECT mode)
S/N:
102 dB (IHF–A weighted, DIRECT mode)
Distortion:
0.005 % (20 Hz ~ 20 kHz) (DIRECT mode)
Rated output:
1.2 V
• Digital
D/A output:
Rated output — 2 V (at 0 dB playback)
Total harmonic distortion — 0.008 % (1 kHz, at 0 dB)
S/N ratio — 102 dB
Dynamic range — 100 dB
Digital input:
Format — Digital audio interface
• Phono equalizer (PHONO input — REC OUT)
Input sensitivity:
2.5 mV
RIAA deviation:
±1 dB (20 Hz to 20 kHz)
S/N:
74 dB (A weighting, with 5 mV input)
Rated output:
150 mV
Distortion factor:
0.03 % (1 kHz, 3 V)
Connections
nAudio section
Getting Started
Specifications
0.02 %
nGeneral
Power supply:
Power consumption:
Maximum external dimensions:
Weight:
AC 120 V, 60 Hz
7.0 A
0.1 W (Standby)
434 (W) x 171 (H) x 414 (D) mm (17-3/32” x 6-47/64” x 16-19/64”)
12.9 kg (28 lbs 7 oz)
nMain remote control unit (RC-1118)
Batteries:
Maximum external dimensions:
Weight:
R6/AA Type (two batteries)
52 (W) x 243 (H) x 21 (D) mm (2-3/64” x 9-9/16” x 53/64”)
184 g (Approx 6.5 oz) (including batteries))
Batteries:
Maximum external dimensions:
Weight:
Specifications
nSub remote control unit (RC-1121)
R03/AAA Type (two batteries)
49 (W) x 220 (H) x 24.5 (D) mm (1-59/64” x 8-21/32” x 31/32”)
114 g (Approx 4 oz) (including batteries)
bFor purposes of improvement, specifications and design are subject to change without notice.
20
www.denon.com
D&M Holdings Inc.
5411 10441 009D