Black & Decker KG2000 Instruction manual

www.blackanddecker.com
2
5
1
4
3
UK
Ireland
Australia
New Zealand
1
KG2000.UK.P65
1
31-07-2003, 09:17
9
5
7
9
6
8
8
10
A
B
14
11
6
12
13
11
6
C
D
2
KG2000.UK.P65
2
31-07-2003, 09:17
14
12
11
6
15 14 12
14
12
11
6
4
E
F
3
KG2000.UK.P65
3
31-07-2003, 09:17
Intended use
Your Black & Decker angle grinder has been designed for
cutting metal and masonry using the appropriate type of cutting
or grinding disc.This tool is intended for consumer use only.
Safety instructions
◆
◆
◆
◆
Warning! When using mains-powered tools, basic safety
precautions, including the following, should always be
followed to reduce the risk of fire, electric shock, personal
injury and material damage.
Read all of this manual carefully before operating the tool.
Retain this manual for future reference.
Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the
tool where there is a risk of causing fire or explosion, e.g. in
the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the
work area or to touch the tool or mains cable.
Dress properly
Do not wear loose clothing or jewellery, as these can be
caught in moving parts. Preferably wear rubber gloves and
non-slip footwear when working outdoors. Wear protective
hair covering to keep long hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles.
Hearing protection should be worn.
Guard against electric shock
Prevent body contact with earthed or grounded surfaces
(e.g. pipes, radiators, cookers and refrigerators). Electric safety
can be further improved by using a high-sensitivity
(30 mA / 30 mS) residual current device (RCD).
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.
Connect dust extraction equipment
If devices are provided for the connection of dust extraction
and collection facilities, ensure that these are connected and
properly used.
Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed
from the tool before operating the tool.
Extension cables
Before use, inspect the extension cable and replace if
damaged. When using the tool outdoors, only use extension
cables intended for outdoor use. Up to 30 m of Black & Decker
extension cable can be used without loss of power.
Use appropriate tool
The intended use is described in this instruction manual. Do
not force small tools or attachments to do the job of a heavyduty tool. The tool will do the job better and safer at the rate
for which it was intended. Do not force the tool. Do not use
the tool for purposes not intended, for example, do not use a
circular saw to cut tree limbs or logs.
Warning! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
Check for damaged parts
Before use, carefully check the tool and mains cable for
damage. Check for misalignment and seizure of moving parts,
breakage of parts, damage to guards and switches and any
other conditions that may affect its operation. Ensure that the
tool will operate properly and perform its intended function.
Do not use the tool if any part is damaged or defective. Do not
use the tool if the switch does not turn it on and off. Have any
damaged or defective parts repaired or replaced by an
authorised repair agent. Never attempt any repairs yourself.
Unplug the tool
Unplug the tool when it is not in use, before changing any
parts of the tool, accessories or attachments and before
servicing.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch.
Be sure that the tool is switched off when plugging in.
Do not abuse cord
Never carry the tool by its cord or pull it to disconnect from the
socket. Keep the cord away from heat, oil and sharp edges.
Store idle tools
When not in use, tools should be stored in a dry, locked up or
high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry,
clean and free from oil and grease.
Repairs
This tool complies with relevant safety requirements.
Repairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable
danger to the user.
4
KG2000.UK.P65
4
31-07-2003, 09:17
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Removing
◆ Remove the screws (9).
◆ Take the guard off the tool.
Warning! Never use the tool without the guard.
Additional safety instructions for Australia and
New Zealand
◆ This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
◆ If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Additional safety instructions for angle grinders
◆ Wear safety glasses or goggles when operating this tool.
◆ Wear ear protection when operating this tool.
◆ Wear gloves when operating this tool.
◆ Do not cut or grind light metal with a magnesium content
exceeding 80%, since this type of metal is flammable.
◆ Only use grinding and cutting discs and other accessories
recommended in this manual.
◆ Make sure that the maximum speed of the grinding or
cutting disc exceeds the no-load speed of the tool.
◆ Do not cut workpieces requiring a maximum depth of cut
exceeding that of the cutting disc.
◆ Never use the tool without the guard, except for sanding.
◆ Do not exert side pressure on the grinding or cutting disc.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Side handle
4. Spindle lock
5. Guard
Assembly
Warning! Make sure that the tool is switched off and unplugged.
Adjusting the guard (fig. B)
The guard can be rotated 180°.
◆ Slacken the screws (9) and the nut (10).
◆ Rotate the guard as required.
◆ Re-tighten the screws and the nut.
Fitting the side handle
◆ Screw the side handle (3) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs (fig. C - F)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size
(see technical data). The maximum thickness for grinding discs
is 6 mm, for cutting discs 3.5 mm.
Fitting
◆ Fit the guard as described above.
◆ Place the inner flange (11) onto the spindle (6) as shown
(fig. C). Make sure that the flange is correctly located on
the flat sides of the spindle.
◆ Place the disc (12) onto the spindle (6) as shown (fig. D).
If the disc has a raised centre (13), make sure that the
raised centre faces the inner flange.
◆ Make sure that the disc locates correctly on the inner flange.
◆ Place the outer flange (14) onto the spindle. When fitting
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. E). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. E).
◆ Keep the spindle lock (4) depressed and tighten the outer
flange using the two-pin spanner (15) (fig. F).
Fitting and removing the guard (fig. A)
Fitting
◆ Place the tool on a table, with the spindle (6) facing up.
◆ Hold the guard (5) over the tool as shown.
◆ Align the holes in the adjusting plate (7) with the screw
holes (8).
◆ Press the guard down and insert the screws (9) into the
holes.
◆ Tighten the screws.
Removing
◆ Keep the spindle lock (4) depressed and loosen the outer
flange (14) using the two-pin spanner (15) (fig. F).
◆ Remove the outer flange (14) and the disc (12).
Use
◆
◆
Warning! Let the tool work at its own pace.
Do not overload.
Carefully guide the cable in order to avoid accidentally
cutting it.
5
KG2000.UK.P65
5
31-07-2003, 09:17
◆
◆
Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
Always position the tool in such a way that the guard
provides optimum protection from the grinding or cutting
disc.
Switching on and off
◆ To switch the tool on, press the lock-off button (2) and
subsequently press the on/off switch (1).
◆ To switch the tool off, release the on/off switch (1).
Technical data
Voltage
Power input
No-load speed
Disc diameter
Disc bore
Spindle size
Weight
KG2000
230
2,000
6,500
230
22
M14
kg 7
VAC
W
min-1
mm
mm
KG2001
230
2,000
8,400
180
22
M14
7
EC declaration of conformity
Warning! Do not switch the tool off while under load.
Hints for optimum use
◆ Firmly hold the tool with one hand around the side handle
and the other hand around the main handle.
◆ When grinding, always maintain an angle of approx. 15°
between the disc and the workpiece surface.
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55014
LpA (sound pressure): 86.6dB(A), LWA (acoustic power) 102.7
dB(A), hand/arm weighted vibration 2.9 m/s2
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
◆
◆
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
◆ Safely dispose of the old plug.
◆ Connect the brown lead to the live terminal in the new plug.
◆ Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 13 A.
Protecting the environment
Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge. To take advantage of this service
please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
◆ The product has been used for trade, professional or hire
purposes;
◆ The product has been subjected to misuse or neglect;
◆ The product has sustained damage through foreign
objects, substances or accidents;
◆ Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
6
KG2000.UK.P65
6
31-07-2003, 09:17
Please register at our website www.blackanddecker.com
to be kept up to date on new products and special offers.
Further information on the Black & Decker brand and our range
of products is available at www.blackanddecker.com.
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road
Tel. 03 9895 9200
Box Hill, Victoria 3128
Fax 03 9899 7465
New Zealand
Black & Decker
Tel. 09 579 7600
81 Hugo Johnston Drive
Fax 09 579 8200
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
7
KG2000.UK.P65
7
31-07-2003, 09:17
TYP
1
KG2000
61
28
23
26
25
22
30
29
27
34
32
33
31
24
39
37
19
35
36
21
20
18
17
62
38
41 42
44
46
45
16
15
40
50
49
14
13
48
47
12
53
43
56
55
52
11
57
54
51
41
10
9
8
60
58
7
6
5
4
3
2
1
59
E13601
WWW.2helpU.com
22-07-03
585998-00
07/03
8
KG2000.UK.P65
8
31-07-2003, 09:17