MK Sound S-125 Operating instructions

MK Sound S-125 Operating instructions
powered subwoofers
operation
manual
MX-SERIES:
MX-2000, MX-1000, MX-1000cc,
MX-100, MX-90, MX-80, MX-70
V-SERIES:
V-125, V-100, V-90, V-1B,
V-2B, V-3B, VX-4, VX-7
Miller & Kreisel Sound Corporation
10391 Jefferson Boulevard
Culver City, CA 90232 USA
(310) 204-2854 FAX (310) 202-8782
© 1994 MILLER & KREISEL SOUND CORP.
powered subwoofers
page 2
TABLE OF CONTENTS
1.
2.
3.
4.
SAFETY INSTRUCTIONS.............................................................................3
INTRODUCTION..........................................................................................4
WHERE TO LOCATE YOUR SUBWOOFER.............................................4
SUBWOOFER HOOK-UP..............................................................................4
STANDARD AMPLIFIER/SPEAKER WIRE CONNECTIONS...................................5
SATELLITE SPEAKER WIRING OPTION 1..........................................................6
V-125 HIGH-LEVEL HIGH-PASS FILTER USAGE..........................................................6
SATELLITE SPEAKER WIRING OPTION 2...........................................................6
WIRING WITH A SEPARATE AMP AND PREAMP (RCA JACKS).............................8
WIRING WITH THE M&K LP-1S OR VF-100 ELECTRONIC HIGH-PASS FILTERS.........9
PLUGGING IN THE SUBWOOFER...................................................................10
5. SATELLITE/SUBWOOFER PHASING TEST...............................................10
6. USE OF THE "FILTER" CONTROL..............................................................11
7. USING TWO SUBWOOFERS....................................................................11
8. FINE-TUNING SUBWOOFER PLACEMENT..............................................12
9. HOME THEATRE USAGE.......................................................................12
CONNECTING TO A SURROUND SOUND RECEIVER OR PROCESSOR.............13
10. SPECIAL INSTALLATION NOTES..............................................................13
11. TROUBLESHOOTING..........................................................................14
REPLACEMENT FUSE VALUES.......................................................................16
12. IF YOU NEED SERVICE.............................................................................16
WIRING DIAGRAMS
FIGURE
FIGURE
FIGURE
FIGURE
FIGURE
1
2
3
4
5
TO AN AMPLIFIER USING SPEAKER WIRES..................................5
SATELLITE SPEAKER WIRING OPTION 1......................................7
SATELLITE SPEAKER WIRING OPTION 2......................................7
USING THE PREAMP INPUTS (RCA JACKS)..................................8
USING AN M&K ELECTRONIC HIGH-PASS FILTER.........................9
WARNING:
To reduce the risk of fire or electric
shock, never expose your M&K Powered
Subwoofer to rain or moisture.
powered subwoofers
page 3
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead,
within an equilateral triangle, is intended
to alert the user of the presence of
uninsulated "dangerous voltage" within
the product's enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK).
NO
USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is intended to alert the
user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
1. SAFETY INSTRUCTIONS
1.
READ INSTRUCTIONS - All safety and operating instructions should be read before this product is operated.
2.
RETAIN INSTRUCTIONS - The safety and operating instructions should be retained for future reference.
3.
HEED WARNINGS - All warnings on this product and in the operating instructions should be adhered to.
4.
FOLLOW INSTRUCTIONS - All operating and use instructions should be followed.
5.
ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they may cause hazards.
6.
WATER AND MOISTURE - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
7.
ACCESSORIES - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the product. Use only with accessories recommended by the
manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions and should
use a mounting accessory recommended by the manufacturer.
8.
POWER SOURCE - This product should be operated only from the type of power source indicated on the marking label. If
you are unsure of the type of power supply to your home, consult your product dealer or local power company.
9.
OVERLOADING - Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.
10.
LIQUID ENTRY - Never spill any liquid of any kind on the product.
11.
SERVICING - Do not attempt to service this product yourself as opening or removing covers, including those over bottom or
side speaker drivers, may expose you to dangerous voltage or other hazards. Refer all service to qualified service personnel.
12.
DAMAGE REQUIRING SERVICE - Unplug this product from the wall outlet and refer servicing to qualified personnel under
the following conditions:
a.
When the power-supply cord or plug is damaged.
b.
If liquid has been spilled, or objects have fallen into this product.
c.
If the product does not operate normally by following the operating instructions. Adjust only controls that are covered
by the operating instructions as an improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to its normal operation.
d.
If the product has been dropped or damaged in any way.
e.
When the product exhibits a distinct change in performance - this indicates a need for service.
13.
REPLACEMENT PARTS - When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result
in risk of fire, electric shock, or other hazard.
14.
SAFETY CHECK - Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
15.
HEAT - This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
powered subwoofers
page 4
2. INTRODUCTION
Congratulations! You have just made perhaps the most exciting and dramatic addition that you
could make to your audio or audio/video system. The new dimension of deep and powerful bass
provided by your M&K Subwoofer will thrill and excite you.
We encourage you to read this owner's manual, as there is a great deal of information provided
here to help you get the best possible performance.
If you have any questions about your Subwoofer, please contact your M&K dealer, or call us
directly at (310) 204-2854, from 8:30 AM to 5:00 PM Pacific Time. We will be more than happy to help
you with any question, no matter how simple or complex it may be.
This manual gives you basic hook-up instructions first, followed by more detailed technical,
installation, and service information.
3. WHERE TO LOCATE YOUR SUBWOOFER
M&K Subwoofers will perform well in just about any room location. In fact, unless your ear is within
a couple feet of the Subwoofer, the deep bass will seem to come exclusively from your Satellite
speakers. (By Satellite speakers, we mean the main speakers used with your Subwoofer). There is
no need to place your Subwoofer between the Satellite speakers or in any specific location in the room.
Except for the V-125, MX-1000 and MX-1000cc, M&K Subwoofers are not magnetically shielded.
Leave 2 - 3 feet of clearance around any television set. This shielding avoids magnetization of the
shadow mask of the television's picture tube, which will distort the television's picture. If this ever
happens to your set, turn it off and on a few times to use the set's built-in degaussing circuitry. If the
problem persists, contact a TV technician and ask him or her to use an external degaussing coil.
No matter where you put the Subwoofer, you must allow room for ventilation of its heatsink and
backplate. The Subwoofer's power amplifier is mounted on the backplate, and it generates heat.
1.
Do not place the Subwoofer against a wall. Leave at least one foot clearance around the
heatsink.
2.
Do not place the Subwoofer where it will be exposed to direct sunlight.
3.
Do not place the Subwoofer near baseboard heaters or forced air heating outlets.
4.
Do not use the Subwoofer outdoors or in a humid environment.
For more detailed placement information, please see Section 8, on page 12.
Do not plug the Subwoofer into an AC outlet until all system wiring is complete.
4. SUBWOOFER HOOK-UP
There are two different ways to connect the Subwoofer to your system. One uses speaker wire,
and the other uses interconnect cable with RCA-type jacks. Read this section before deciding
which is best for your system.
powered subwoofers
page 5
Look at the back panel of the Subwoofer. You will see two RCA input jacks labelled "FROM
PREAMP," and two sets of speaker wire input terminals labelled "FROM AMPLIFIER" and "TO
SPEAKERS." You must choose to use either the speaker wire inputs or the RCA jack inputs.
STANDARD AMPLIFIER/SPEAKER WIRE CONNECTIONS
The most common way to hook up the Subwoofer is to connect it to your receiver or amplifier using
speaker wires. You make the same kind of connections that you would use for your Satellite (or main)
speakers, except that both the left and right channels go to the Subwoofer. (If you are using two
Subwoofers, connect one channel only to each Subwoofer).
1.
2.
Run speaker wire between the Amplifier's Left channel output terminals and the
Subwoofer's Left channel "FROM AMPLIFIER" terminals.
a.
Connect the Amplifier's Left channel Positive (+) terminal and the Subwoofer's
Left RED (+) "FROM AMPLIFIER" terminal.
b.
Connect the Amplifier's Left channel Negative ( — ) terminal and the Subwoofer's
Left BLACK ( — ) "FROM AMPLIFIER" terminal.
Make matching connections for the Right channel. See Figure 1.
FIGURE 1 - TO AN AMPLIFIER USING SPEAKER WIRES
IMPORTANT NOTE FOR SURROUND SOUND SYSTEMS:
When the Subwoofer is connected to the Left and Right amplifier outputs, and the controller is in
Pro-Logic mode, the Center channel WIDE/NORMAL switch MUST be set to the NORMAL mode. If
the switch is set to the WIDE mode, the bass content of the Center channel will not be fed to the
Subwoofer, and you will lose a significant amount of bass.
powered subwoofers
page 6
You now have two options for connecting your Satellite speakers.
SATELLITE SPEAKER WIRING OPTION 1
With this option, you connect the wiring for the Satellites directly to the Subwoofer. There is no
performance advantage with this method, but it may require less speaker wire and be more convenient.
1.
2.
Run speaker wire between the Subwoofer's Left channel output terminals and the Left
Satellite speaker.
a.
Connect the Subwoofer's RED (+) "TO SPEAKERS" terminal to the Positive (+)
terminal on the back of the Left Satellite speaker.
b.
Connect the Subwoofer's Left BLACK ( — ) "TO SPEAKERS" terminals to the
Negative ( — ) terminal on the back of the Left Satellite speaker.
Make matching connections to the Right channel Satellite speaker. See Figure 2.
V-125 HIGH-LEVEL HIGH-PASS FILTER USAGE
The V-125 has a high-level high-pass filter (other M&K subwoofers do not have this filter). When
your main speakers are connected to the speaker terminals on the back of the V-125, the low bass
frequencies below about 80 Hz (which the V-125 reproduces) are filtered from your Satellite speakers.
This will significantly reduce the bass demand placed on your main speakers and can make a
noticeable improvement in their sound quality, especially in the midbass and lower midrange. The filter
may make other subtle changes to the sound quality, however, so you may want to experiment with
and without the filter to determine the best configuration for your system.
To use this filter, simply connect the speaker wire from the left and right channels of your amplifier
or receiver to the ""FROM AMPLIFIER" terminals on the V-125. Then connect your left and right main
speakers to the "TO SPEAKERS" terminals on the back of the V-125. See Figure 2.
If you have a Dolby Pro-Logic system, we recommend that you set the CENTER CHANNEL switch
on the Dolby processor or receiver to the NORMAL mode. This provides a low bass filter for the center
channel speaker and also insures that the bass from all three front channels is fed to the subwoofer.
This high-pass filter does not operate when the V-125 is connected with interconnect cable using
RCA-type jacks. If you want a low (preamp) level Electronic High-Pass filter, contact your M&K dealer.
SATELLITE SPEAKER WIRING OPTION 2
This option has the Satellite speakers directly connected to your amp or receiver. It requires two
sets of speaker wires — one set running to the Satellite speakers and the other set to the Subwoofer.
Please note that (except for the V-125) there is no High-Pass filter built into the Subwoofer.
Connect the Satellite speakers to your Amplifier, following the Satellite speakers' instructions.
Use the same Amplifier output terminals that the Subwoofer is connected to. Do not, however, connect
the Satellite speakers to the Subwoofer.
powered subwoofers
page 7
FIGURE 2 - SATELLITE SPEAKER WIRING OPTION 1
(ALSO SHOWS USE OF THE V-125's HIGH-LEVEL HIGH-PASS FILTER)
If your Amplifier has two sets of speaker outputs (e.g., A and B), you can connect the Satellites
to one set and the Subwoofer to the other. But if you get weak or no output when you connect your
speaker this way, connect both sets of speaker wires to the same output terminals. See Figure 3.
FIGURE 3 - SATELLITE SPEAKER WIRING OPTION 2
If your receiver or amp has two sets of speaker outputs, you may connect the
Satellite speakers to one set of outputs and the Subwoofer to the other set.
powered subwoofers
page 8
Unless you have a V-125, a full-range signal (including deep bass) is fed to your Satellites. To
roll off (filter) the signal fed to the Satellite speakers to achieve true biamplification, you must:
1.
Have a separate amp and preamp OR a receiver or integrated amp that allows you to separate
its amp and preamp stages.
2.
Add an M&K Electronic High-Pass Filter to your system. See Page 9 for more information.
WIRING WITH A SEPARATE AMP AND PREAMP (RCA JACK INPUTS)
The "FROM PREAMP" RCA input jacks on the Subwoofer allow you to directly connect the
Subwoofer to preamp-level components such as preamplifiers, integrated amps and receivers with
preamp outputs, Electronic High-Pass filters, crossovers, surround sound processors, etc.
These inputs will give slightly better bass quality than the speaker wire inputs, because they
bypass the receiver or amplifier. If you have only one set of preamp outputs, and are not using an M&K
Electronic High-Pass Filter or a crossover, you will have to use a Y-connector to feed both the amplifier
and the Subwoofer. The V-125's high-pass filter does not work when the RCA jack inputs are used.
In many cases, the slight improvement this makes in bass quality may be offset by a slight
degradation of the Satellite speakers' sound quality. We generally recommend against using a
Y-connector just to use the Subwoofer's "FROM PREAMP" jacks, but please feel free to experiment.
To connect the Subwoofer in this way, simply run a set of shielded RCA - RCA interconnect cables
from the output jacks on your component to the "FROM PREAMP" jacks on the Subwoofer's
backplate.See Figure 4. If you are using two Subwoofers, run the left channel interconnect cable to
FIGURE 4 - USING THE PREAMP INPUTS (RCA JACKS)
If you have one Preamp Output, connect both the Subwoofer and the Amplifier to it.
powered subwoofers
page 9
the left Subwoofer and the right interconnect cable to the right Subwoofer.
WIRING WITH THE LP-1S & VF-100 ELECTRONIC HIGH-PASS FILTERS
The M&K LP-1S and VF-100 Electronic High-Pass Filters can improve the performance of any
system that allows for separation of its preamp and power amp stages by filtering the bass signal fed
to the main amplifier and Satellite speakers.
To use these filters with an integrated amp or receiver, the amp or receiver MUST have back panel
RCA jacks labelled Preamp/Main Output AND Power Amp/Main Input. There may be a switch or
jumper connections between them.
These filters will give you greater dynamic range, lower distortion, and an increased maximum
output level. If you have any questions about the suitability of your components, please contact your
M&K dealer or the factory.
To connect one of these filters into your system, run one set of shielded RCA — RCA interconnect
cables from the receiver, amp or preamp's Main Output to the set of input jacks labelled "INPUT" (on
the LP-1S) or "FROM PREAMP" (on the VF-100). Run another set of interconnects from the "TREBLE
OUT" (LP-1S) or "TO MAIN AMP" (VF-100) jacks to the receiver or amp's Power Amp Input. Run a
third set of interconnects from the "BASS OUTPUT" (LP-1S) or "TO SUBWOOFER" (VF-100) jacks to
the Subwoofer's "FROM PREAMP" jacks. See Figure 5.
FIGURE 5 - USING AN M&K ELECTRONIC HIGH-PASS FILTER
With an integrated amp or receiver, the preamp and power amp will be on the same chassis.
powered subwoofers
page 10
PLUGGING IN THE SUBWOOFER
Once all the speaker wires or preamp interconnect cables are in place, you are ready to plug in
the Subwoofer. Set the "BASS LEVEL" control to "MIN". Then plug the AC cord in. You should hear
a thump from the Subwoofer. This is the normal sound of its power supply charging and discharging
when it is plugged in and unplugged.
Once your system wiring is complete and the Subwoofer is plugged into the wall, leave it plugged
in, even when the system is turned off. The normal mode of operation for the Subwoofer is to remain
plugged in 24 hours a day. Among other things, this means that you don't have to walk over to the
Subwoofer to turn it on every time you want to use the system.
If you decide to plug the Subwoofer into a switched outlet on another component, that outlet must
have the following minimum power ratings:
Minimum of 150 watts:
V-90, V-2B, V-3B, VX-4, VX-7
Minimum of 200 watts:
MX-1000, MX-1000cc, MX-90, MX-80, MX-70, V-1B, V-125
Do not use a switched outlet with the MX-2000, MX-100, and V-100.
Now, play some music through your system to make sure that the Satellite speakers are working
properly. If they are, carefully advance the "BASS LEVEL" control. The Subwoofer should begin to
play. Set the "BASS LEVEL" control where the Subwoofer sounds in balance with the Satellite
speakers. If the system is not working properly, unplug the Subwoofer and check all of your
connections. Call your dealer or the factory if you cannot solve any problem.
The best way to set the level of the Subwoofer is to do it by ear, listening over several hours or
days to familiar recordings. Make adjustments to the level in small increments, depending on whether
the bass level sounds too high or too low. Of course, you can always deliberately set the level higher
or lower than "flat" if you need a higher bass level or if you don't want to disturb your neighbors.
5. SATELLITE/SUBWOOFER PHASING TEST
SATELLITE/SUBWOOFER PHASING TEST
You are now almost finished with the basic set-up. But before you can sit down to enjoy your new
Subwoofer, you need to perform one simple Phasing Test. This test insures optimum sound in the
critical bass frequencies where your Subwoofer and Satellite speakers overlap.
NOTE: If you have the V-125 subwoofer, ignore the instructions that make reference to changing
the Satellite speaker inputs. In place of changing the inputs, all you have to do is move the "PHASE"
switch on the V-125's back panel from either up (+) or down (—) to the opposite position.
Play a familiar CD, LP, or tape with steady, consistent bass. Listen carefully to the "mid-bass"
(75 - 125 Hz) region — the part of the spectrum where electric or string basses and drums are found.
Then, reverse the Positive and Negative speaker inputs on the back of BOTH Satellite speakers. Move
the lead on the Positive (+) terminal to the Negative (—) terminal, and vice versa.
Alternately, you can do this at the Subwoofer's "TO SPEAKERS" terminals, but never switch the
inputs at both the backs of the Satellite speakers and the Subwoofer.
powered subwoofers
page 11
Now listen to the same musical passage as you did earlier, concentrating on the mid-bass region.
If you hear less bass, the original connections were correct. If you hear more bass, the new
connections are correct.
If you have two Subwoofers, perform one test for each Subwoofer. When you perform each test,
make sure the other Subwoofer is not operating by either unplugging its input cable or its power cord.
Another methods of setting correct phase requires the use of a pink noise source and a spectrum
analyzer. If you have access to these, instead of listening, place the microphone at the main listening
position and look at its display in the "mid-bass" region of 70 - 125 Hz. The wiring or switch position
that shows the greatest output in that region is the correct phase.
You need to perform this test because when Satellite speakers are located separate from a
Subwoofer, each speaker is at a different distance from your ear. In some cases, the difference will
be just enough so that the output from the Subwoofer arrives out of phase with the output of the
Satellites. When this happens, that critical mid-bass is actually cancelled. You should re-do this test
any time you move your speakers.
If you want to experiment further, you can move the Satellite speakers either towards or away from
your listening position, making changes in small increments. This will "focus" the system's sound to
its optimum. When you hear the best balance between stereo image localization and maximum impact
and output in the mid-bass, you have the ideal location.
6. USE OF THE "FILTER" CONTROL
The back panel control labelled "FILTER" sets the upper rolloff point of the Subwoofer, eliminating
mid-bass and midrange signals that are being reproduced by your Satellite speakers. The control is
a means of "fine-tuning" the transition between your Subwoofer and Satellite speakers, and it provides
a rolloff of 18 dB/octave up to 125 Hz, where the filter shifts to 36 dB/octave. In most systems, including
M&K Satellites, 85 Hz gives the best blend. If you don't want to experiment, set the control at 85 Hz.
The goal is to get a balanced acoustic output in your room. This is not necessarily the same as
flat electrical output. Rooms typically reinforce bass frequencies around 100 Hz, so by leaving an
electrical gap, you may actually get a smooth acoustical response where it matters, in the room.
Think of this control as a "mid-bass" fine tuning adjustment that you set to achieve the best
transition between the Satellite speakers and the Subwoofer. When you hear a smooth sound overall,
well balanced between the deep bass and the rest of the audible spectrum, the control is set properly.
7. USING TWO SUBWOOFERS
Using two Subwoofers in your audio/video system gives you the ultimate in bass performance.
You'll hear improved impact and definition, as well as greater output and dynamic range. If the
Subwoofers are located in different parts of the room, you will get a much smoother bass response,
as the room modes excited by one woofer are effectively reduced by the presence of the other.
Wiring with two Subwoofers is very simple. Instead of running two sets of speaker wires or two
interconnect cables to one Subwoofer, run one speaker wire or interconnect to each Subwoofer. You
can do this because both the left and right channel input signals are combined in the Subwoofer's input
stage. The only thing this changes is amplifier gain, and, if you want, you can compensate by setting
powered subwoofers
page 12
the "BASS LEVEL" control slightly higher.
8. FINE-TUNING SUBWOOFER PLACEMENT
If you have the physical space in your room and the interest to experiment with the placement of
your Subwoofer, you may be able to optimize its location and sound. If you want to do this, listen to
the Subwoofer after it is hooked up, using a familiar CD, LP, or tape with good bass content. After you
move the subwoofer from one location to another, listen to the music again, paying attention to the
changes in the amount and quality of bass reproduction.
Ultimately, the amount and quality of bass you get in your room are very dependent on the room
itself. Low frequency bass sounds are affected most by the size of the room and the method of
construction used to build it. All rooms are different when it comes to reproducing bass, and in any
given room, bass quality changes when the Subwoofer is moved from one location to another.
A simple rule to remember is that you get more bass when you move the Subwoofer towards any
wall or corner. Moving it away from a wall or corner gives you less bass. Remember that the floor also
loads the Subwoofer, and that maximum bass is found with the woofer on the floor in a corner.
The Subwoofer will probably sound its best when it is on the floor, within a foot or two of one wall,
either in or within a few feet of a corner. This provides for good "loading" to the room, and is the best
place to start when experimenting.
In some rooms, a corner location may excite resonance modes, resulting in a "muddy" or "boomy"
sound. In these rooms, a more central location along a wall, away from the corner, gives the best
results. If you experiment, try to find a spot where no bass notes seem to overpower others and the
overall sound is powerful and clean. The goal is to achieve a smooth sound quality, with the entire bass
spectrum equally prominent. Again, in most rooms, this will be along one of the room walls, probably
close to a corner (or directly in the corner), rather than in the center of the room.
Because the Subwoofer generates a great deal of energy, its output may vibrate objects close to
it. If you hear such vibration, you may want to move the Subwoofer or act to damp the vibration of
nearby objects.
One Subwoofer is sufficient in a stereo system because of the nature of human hearing. The earbrain hearing system is unable to locate the direction of bass sounds below approximately 150 Hz. The
direction of low frequency sounds (such as drums being struck) is determined by higher frequency
overtones and harmonics that are reproduced by the Satellite speakers.
All M&K Powered Subwoofers have exceptionally sharp (36 dB/octave) low-pass filters to remove
the midbass and midrange frequencies unwanted in a Subwoofer. This makes your M&K Subwoofer
truly non-directional.
We realize that you are not going to design your room around the Subwoofer. Use these
suggestions as guidelines, remembering that the Subwoofer will work well just about anywhere in the
room. This section is intended to help you find a good balance between sound quality and aesthetics.
9. HOME THEATRE USAGE
If you are using your Subwoofer in a Home Theatre system, set-up is essentially the same as for
a music system, so all of the previous instructions apply to both types of systems.
powered subwoofers
page 13
In some cases, however, you may prefer the subwoofer set to a higher playback level for video
sources. This may occur when video sources (especially older films and some television) have very
little deep bass present. You may also want to exaggerate the effect to make spectacular video sources
even more impressive!
When your subwoofer is going to be located close to a television set, remember to leave 2 - 3 feet
of clearance between the television and subwoofer, unless the subwoofer is magnetically shielded
(V-125, MX-1000 and MX-1000cc only).
CONNECTING THE SUBWOOFER TO A SURROUND
SOUND RECEIVER OR PROCESSOR:
The preferred connection from a surround sound amp or controller is from a SUBWOOFER
OUTPUT RCA jack. This connection usually insures that a full bass signal is fed to the subwoofer. If
your component doesn't have a subwoofer output jack, connect the Subwoofer to the front Left and
Right channel speaker outputs (don't use the Center channel).
VERY IMPORTANT: When the Subwoofer is connected to the Left and Right amplifier outputs
(this means using speaker wires), and the controller is in Pro-Logic mode, the Center channel WIDE/
NORMAL switch MUST be set to the NORMAL mode. If the switch is set to the WIDE mode, the bass
content of the Center channel will not be fed to the Subwoofer, and a significant amount of the bass
in the material you are listening to will be lost.
10. SPECIAL INSTALLATION NOTES
MX-2000, MX-100, MX-90, MX-80, V-100, V-90:
An enclosed hardware kit contains four black metal spikes, threaded at one end and tapering to
a sharp point at the other. Depending on their orientation, they can be used either as spikes or rubber
feet. Do not use the spiked feet on hardwood or tile floors. They can damage the floor surface.
By mounting these spikes into the threaded inserts mounted in the bottom of the Subwoofer, you
can elevate the Subwoofer, and on carpet, couple it more tightly to that floor. On hardwood, tile, or
concrete, the spikes should be inverted, with the point mounted facing into the cabinet. One of the black
rubber feet provided should then be pressed over the exposed flat end of the foot.
The threaded inserts are found in the four corners of the cabinet's bottom. The MX-2000 has a
fifth insert, which allows you to use three of the five in a triangular pattern. The inserts are 1/4 - 20,
that is, 1/4 inch in diameter and 20 threads per inch. This is compatible with the most spikes, "cones,"
"tip-toes," etc. offered by other manufacturers.
To properly secure the feet to the cabinet, you must use the provided washer and jamb nut on the
threaded portion of the foot. The washer goes first, with the nut over it, holding the washer securely
in place. This prevents damage to the spike and insert if something moves the cabinet sideways.
MX-100, MX-90, MX-80, MX-70:
Because your M&K MX-series Subwoofer uses an "inverted" driver that fires down into the floor,
it loads differently to the room than a conventional speaker or forward-firing Subwoofer. This means
that you may want to experiment a bit more with its placement and setup to get optimum sound quality.
1.
Because of its downward-firing driver, your MX Subwoofer may be more susceptible to
powered subwoofers
page 14
producing a "boomy" sound if it is located in a corner. Always try the subwoofer first in a
corner. If it sounds "boomy," move it a few feet out of the corner.
2.
While your Subwoofer performs perfectly well directly on the floor, the distortion cancellation
of its push-pull design and its frequency response are best when the Subwoofer is slightly
elevated. We therefore strongly recommend that you use the enclosed feet to raise the
Subwoofer off the floor.
3. Read Section 6, (page 11) Use of the Filter Control, carefully. The setting of this control is more
critical with your MX model Subwoofer. With these models it is more likely that you will find the optimum
setting to be below the 85 Hz recommended for other models.
MX-70:
The MX-70 gives a very high level of performance in a compact cabinet. Therefore, it is likely to
be installed in both vertical and horizontal locations. To avoid having its inverted driver exposed in
installations where the cabinet is horizontal, the MX-70 has two speaker grills.
If you locate the MX-70 with the inverted driver firing down towards the floor, leaving the grille on
will not affect sound quality. Instead, if you want to save the grille, you can remove and store it. In its
place, use the four black caps provided with your MX-70. These caps fit over the grille pegs on the
cabinet "bottom" (where the inverted driver is located). Just snap these in place to use them as feet.
MX-1000 & MX-1000cc:
The MX-1000 and MX-1000cc Subwoofers are specially shielded for use with large-screen directview monitor television sets.
Take special care when installing your MX-1000 or MX-1000cc. Like most all "shielded" speakers,
a magnetic lobe exists, directly in front .of each driver (to the left and right sides of the pedestal). Your
set should not be exposed to this lobe. Therefore:
1.
Do not mount the television on the MX-1000 or MX-1000cc from the side. Place it on the
pedestal from the front or the back only.
2.
The television must face forward on the pedestal, perpendicular to the speaker drivers. Do
not mount the set so that it faces sideways.
11. TROUBLESHOOTING
Your M&K Subwoofer amplifier circuit provides high reliability, and, if necessary, easy modular
replacement of parts. This guide will help you to solve or diagnose most problems that can occur with
your Subwoofer. In the event that a fuse blows, you must replace it with a fuse of the correct value
to avoid a fire hazard and to maintain your warranty protection.
1.
If your Subwoofer has no output:
a.
Make sure that the Subwoofer is plugged into an AC outlet.
b.
Check the "BASS LEVEL" control and make sure that it is set above the
"MIN" position. Rotate it clockwise if it is set to the "MIN" position.
powered subwoofers
page 15
c.
Check the red LED on the Subwoofer's back panel. If the LED is not lit,
check the AC fuse next to the LED. Unplug the Subwoofer before
changing the fuse. See instructions on Page 15. If the element inside the
fuse is broken, replace the fuse. If it blows again, contact your dealer or M&K.
d.
If the red LED is still lit, try this test: Turn the "BASS LEVEL" control
to "MIN". Plug a standard RCA cable into the "FROM PREAMP" jacks.
Lightly touch the plug at the free end of the cable, while slowly turning the
"BASS LEVEL" control clockwise. If you hear noise from the Subwoofer when
you touch the cable, the Subwoofer is functioning. Look elsewhere in your
system for the problem. If you hear no noise, contact your dealer or M&K.
e.
Make sure that the input cables are OK. Double check your connections. If
necessary, replace any defective cables or speaker wires.
2.
If, after operating the woofer at high volume levels for a long time, the woofer
cuts out or becomes intermittent:
Your Subwoofer has a protection circuit that protects it from overheating. After continuous
operation at high volume levels, this circuit kills the power to the Subwoofer. When it activates,
the sound may switch in and out rapidly, with a "fluttering" sound. If this happens, unplug the
unit and let it sit for at least half an hour. After that time, plug it back in. It should operate
normally. If you find this happens frequently, contact the factory for advice.
3.
If you are using the "FROM AMPLIFIER" terminals, and the Subwoofer has very
little output:
Make sure that the input cables are in phase. Reverse the (+) and the ( — )
connections for ONE CHANNEL ONLY at the "FROM AMPLIFIER" terminals. If the
problem remains, put the cables back as they were. Then perform the test in Step 3.
3.
If the midbass range (the area of transition between Subwoofer and Satellite
speakers) sounds weak:
Refer to Section 4, Phasing Test, on page 9. Reverse the (+) and ( — ) connections
at the back of BOTH Satellite speakers. The wiring configuration that gives the most
bass is correct.
4.
If you are using the "FROM PREAMP" input terminals, and you hear
a thump through the Subwoofer every time you turn the system on:
Either the preamp, receiver, or surround sound processor is generating the thump,
and the Subwoofer is reproducing it. To eliminate this problem, switch to the speaker
wire "FROM AMPLIFIER" input terminals.
5.
If you hear a persistent hum or buzz through the Subwoofer:
Because the Subwoofer reproduces the 60 Hz hum frequency, it is often blamed for
causing hum that originates elsewhere in the system. Always avoid running all
speaker wires and RCA interconnect cables near to AC cords and component power
supplies. Wires and cables running close to AC lines are a common source of hum.
If necessary, reroute your cables.
To identify the source of hum, remove all input cables to the Subwoofer, but leave it
plugged into the AC outlet. Carefully turn the "BASS LEVEL" control up towards the
"MAX" position. If you hear hum coming from the Subwoofer's speaker driver, the
Subwoofer is the source of the hum. If you hear no hum or less hum, the problem is
powered subwoofers
page 16
probably coming from another component.
Hum can also be caused by AC ground loops. If the Subwoofer is plugged into a
separate AC outlet, try plugging it into the same outlet used for your amplifier or
receiver, or reverse the polarity of its AC plug. If these suggestions do not solve
your problems, contact your dealer or M&K.
6.
If there is an unusual sound coming from the Subwoofer with no music playing:
Try removing the input cables as described in Step 5 above. If the noise disappears, it is coming
from another component. If it does not go away, contact your M&K dealer or the factory.
IF YOU NEED TO REPLACE THE EXTERNAL FUSE:
Disconnect supply cord before changing fuse. Replace fuse only with same type. Remove the
fuse cap by pushing it in while turning it in the direction of the arrow. Look carefully at the fuse. If the
wire filament inside the glass is broken, replace the fuse ONLY with one of the identical size and value.
Using a larger fuse will void your warranty AND MAY CREATE A FIRE HAZARD. Plug the Subwoofer
back in and try again. If it does not work, unplug it immediately, and contact your M&K dealer or the
factory for service.
REPLACEMENT FUSE VALUES
Replace only with same type 3AG-250 VAC SLO-BLO 1 1/4" x 1/4" fuse.
MODEL
110 v
220 v
MODEL
110 v
220 v
MX-2000
6 amp
3 amp
MX-1000
2 amp
1 amp
MX-100
4 amp
2 amp
MX-90
2 amp
1 amp
MX-80
1.25 amp
.75 amp
MX-70
2 amp
1 amp
V-100
4 amp
2 amp
V-125
2 amp
1 amp
V-90
1.25 amp
.75 amp
V-1B
2 amp
1 amp
V-2B
1 amp
.75 amp
V-3B
1.25 amp
.75 amp
VX-4
1 amp
.75 amp
VX-7
1 amp
.75 amp
12. IF YOU NEED SERVICE
Contact your dealer or M&K with a complete description of the problem. Please have the unit's
model and serial numbers (found on the back of the cabinet), date of purchase, and the name of your
dealer. You can call M&K between 8:30 AM and 5:00 PM Pacific Time, Monday through Friday, at (310)
204-2854. If you call outside these hours, leave a message, and we will return your call.
DO NOT RETURN YOUR SPEAKERS TO THE FACTORY FOR
SERVICE WITHOUT OBTAINING PRIOR AUTHORIZATION.
All M&K powered subwoofers carry a three year limited parts and labor warranty. This warranty
is transferable to new owners up to three years from the date of original purchase, and it includes
Subwoofer amplifiers. It does not cover abuse, misuse, repairs by unauthorized service stations,
speakers without serial numbers, and those damaged in shipping or by accident. If you have any
questions about the warranty, please contact M&K.
rev 07.1094
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement