Quoizel UPEV8701WT Wall Sconce Assembly Instruction Sheet

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

.

.

Quoizel, Inc.

6 Corporate Parkway

Goose Creek, SC

29445

Customer Service

Phone 631.273.2700

Fax 631.231.7102

www.quoizel.com

Assembly Instruction Sheet #IS-UPEV8701WT

For Style UPEV8701WT

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Bulb Recommended: (1) Medium Base Edison Bulb 60W Maximum (supplied)

Estimated Assembly Time: 20-30 minutes

Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement parts.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

Part

A

B

E

F

C

D

G

H

Description

Crossbar

Nipple

Lock Washer

Hex Nut

Mounting Ball

Shade

Edison Bulb

Fixture Body

Quantity

1 pc.

1 pc.

1 pc.

1 pc.

1 pc.

1 pc.

1 pc.

1 pc.

A

B

C

D

E

G

F

H

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com

2012 QuoizelInc.

1of4

October2012

UPEV8701WT

FINISH: WESTERN BRONZE

2

11”

6.5” Dia.

6”

3.5” Dia.

8.5”

1

2.4mm

13Ga

GND

QUOIZEL

R

(1)60W Medium

Base Edison Bulb

(Supplied) NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2

"

NO.

PART NUMBER

1

2

18701WTUPEV

G3443SH

REPLACEMENT PART DESCRIPTION

BASE WESTERN BRONZE UPEV8701WT

GLASS SHADE - CLEAR

2of4

REQ.

1

1

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

.

.

Assembly Instruction Sheet #IS-UPEV8701WT

For Style UPEV8701WT

STEP 1 - Attach Crossbar to Outlet Box

A. Secure the Crossbar (A) to the outlet box with outlet box screws (not supplied). Tighten until snug.

Figure 1 Outlet Box

Crossbar

Outlet Box

Screw (not

Supplied)

Mounting Hole

STEP 2 Attach Nipple to Crossbar

A. Thread one Hex Nut (D) onto the top end of the Nipple

(B).

B. Place one Lock Washer (C) over the top end of the

Nipple (B) and then thread the Nipple (B) into the center lock hole of the Crossbar (A).

C. Using pliers, thread the Hex Nut (D) against the

Crossbar (A) and hand tighten until snug.

Figure 2

Crossbar

Nipple

Lock Washer

Hex Nut

STEP 3

-

Make Wire Connections

A. Use standard wire connectors to make all wire connections. (Connectors are not included with fixture.)

Strip and prepare wire ends according to instructions supplied with connectors.

B. Connect White Supply Wire from the Outlet Box to White

Wire from fixture.

C. Connect Black (or Red) Supply Wire from the Outlet Box to Black Wire from fixture.

D. Connect Ground Wire from the Outlet Box to Ground

Wire from fixture.

E. Twist connectors until wires are tightly joined together.

F. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.

White wire from supply White wire from fixture

Figure 3

Black wire from supply

(or Red)

Ground wire from supply

Black wire from fixture

Ground wire from fixture

Figure 4

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com

2012 QuoizelInc.

3of4

October2012

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

.

.

Assembly Instruction Sheet #IS-UPEV8701WT

For Style UPEV8701WT

STEP 4 - Attach Fixture Body to Nipple

A. Place the Backplate of the Fixture Body (H) over the

Nipple (B) and secure with the Mounting Ball (E). Hand tighten until snug.

Mounting Ball

Outlet Box

Nipple

Backplate

Figure 5

STEP 5 - Attach Shade to Fixture Body

A. Place the Shade (F) over Socket, seat onto Shade

Holder as shown.

Shade

STEP 6 Install Bulb

A. This fixture uses Edison bulb (supplied) with a standard screw base. Maximum 60 watts.

B. Insert bulb and screw properly into place.

Your fixture is now assembled and ready to use.

Enjoy!

Socket

Shade Holder

Figure 6

Bulb

Socket

Figure 7

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700 or visit us on-line at www.quoizel.com

2012 QuoizelInc.

4of4

October2012