HD 3G/HD-SDI Monitor
12.1" high resolution monitor
Dear users:
Thank you for purchasing our Photography HD-SDI LCD Monitor Kit. This
product employs advanced integrate circuits and high quality TFT LED modules.
It's high brightness, low power consumption stable performance and emits no
radiation advantages, which make it ideal for any DV and HD video camera.
This monitor has various installation ways, and can be equipped with folding
bracket to use as a desktop monitor, the monitor on the back is reserved for VESA
(100 * 100mm; 75 * 75mm) mounting hole, on the side of the four directions left 1/4
inches screw holes, customers can install various styles of mounting bracket
according to their needs.
This monitor is not only with SDI(Can choose), HDMI, COMPONENT (YPbPr),
Composite Video, Audio signals input, and also has SDI ( Can choose ),
COMPONENT (YPbPr), Composite Video, Audio signals output port. To meet
different user needs.
Product feature:
◆ Peaking focus assist(peaking filter)
◆ Canon 5D MarkII mode (CAMERA)
◆ Image magnification/scaling, image flip function
◆ Picture in picuter(PIP)function
◆ Line field blanking
◆ Tally indicator
◆ Front earphone hole
◆ Monochrome display: color, black, red, green, blue, closed
◆ Screen ratio:panorama, real mode, 4:3, full screen, scaling1, scaling 2
◆ Scan mode: standard, under scan, over scan
◆ Screen marker: off, 96%, 93%, 90%, 85%
◆ Display pixel and the pixel point to point
1
To insure best use of the unit, please read the user's manual carefully .
CAUTION
1. Please use the adapter attached in the accessory.
2. Do not expose this product to direct sunlight, heat or humid conditions
3. Keep away from strong light while using this product so as to obtain the
clearest and the most colorful picture.
4. Please avoid heavy impact or drop on the ground.
5. Do not use chemical solutions to clean this unit. Please simply wipe with a
clean soft cloth to keep the brightness of the surface.
6.
Without adjustable component in the unit, please do not take apart or repair
the unit by yourself, to avoid damage the product.
CONTENTS
1. Front panel view----------------------------------------------3
2. Rear panel view -----------------------------------------------4
3. Key operation instructions--------------------------------5
4. Menu function introduction-------------------------------5
5. Signal mode form --------------------------------------------9
6. SDI support mode form -----------------------------------10
7. Power input ways -------------------------------------------10
8. TALLY use and connect- ----------------------------------11
9. Accessories ---------------------------------------------------12
10. Parameter ----------------------------------------------------13
11.Trouble shooting---------------------------------------------14
2
1.
Front panel view
1.
Power indicator light
2.
► :Volume up adjust, in OSD menu for confirm and value increase
3.
◄ : Volume down adjust, in OSD menu for confirm and value
decrease
4.
: Image pause key, in OSD menu for adjust selection key (down)
5.
: Image magnification key, in OSD menu for adjust selection
key(up)
6.
MENU:
Menu key
7.
B / W : Image color, black and white, Monochrome (red, green, blue)
switch key
8.
16:9/4:3: Image proportion adjustment key
9.
CAMERA:Photography model confirm key
10. SCALE:
Peaking focus assist confirm key
11. MODE:
Input signal selection key
12.
Earphone jack(audio output)
:
13. TALLY (indicator)
3
2.Rear panel view
● Rear panel instruction
1、
HDMI HD signal input
2、4、6、
Component Ypbpr input
3、5、7、
Component Ypbpr output
8、
Composite video input
9、
Composite video output
10、11、
Audio input (Left and right double channel)
12、
3G-SDI input (Can choose)
13、
3G-SDI output(Can choose)
14、
Power DC12V input
15、
Power switch
16、
Tally signal input
17、
Battery plate
4
3.
Key operation instructions
If in the operating status, press button“
Press the unit button“
(display result)
”or“
(sound)
”to select the options which you need:
(system setting)
select the button you need, press“
OSD menu, repress button “
4.
”, then enter into OSD mode.
”or“
(scan position adjust), after
on the unit to confirm, if need to exit
”.
Menu function introduction
● Display result setting
(this setting has 2 pages menu)
Press "
" key, pop up OSD menu as below,"
, press "
" or "
" to confirm, With "
adjustment project,then use "
Press"
◆
" or "
" or "
" or"
" to select
"button to choose
" to adjust or select the adjustment.
" to exit.
Menu page 1 picture
Contrast:
To adjust the brightest and darkest ratio of the image
Brightness:
To adjust the image's brightness
Saturation :
To adjust the saturation
Sharpness:
To adjust the depth to the image
Color Temp:
To adjust the RED, GREEN, BLUE of the color
5
Picture Mode: To set brightness, softness, user to the image
effect(under the color temperature)
◆
Menu page 2 picture
Aspect Ratio:
Tint:
To choose the aspect ratio, 16:9/4:3
In the composite video mode, adjust NTSC color
signal, the other modes are not valid
● Sound setting
Press "
, press "
"key, pop up OSD menu as below,"
" or "
" to confirm, With "
adjustment project,then use "
Press"
" or "
" or"
"to select
"button to choose
" to adjust or select the adjustment.
" to exit.
Volume: To adjust the volume
Balance: To adjust 2-channel(L& R)
6
" or "
● System setting
(this setting has 3 pages menu)
Press "
" key, pop up OSD menu as below,"
, press "
" or "
" to confirm, With "
adjustment project,then use "
Press"
◆
" or "
" or"
" or "
" to select
"button to choose
" to adjust or select the adjustment.
" to exit.
Menu page
1 picture
Language: Chinese, English
PIP: To display two input signal picture at the same
time, adjust position, size and mode
SDI:
Sreen markers:
HD SDI switch optional
Picture framing marker selection frame
Scan mode: To deal with special image
Effect: To select the OSD display effect
◆
Menu page 2 picture
Menu Transparency:
To adjust transparence of the OSD
7
Menu timer : To control the automatic disappearance time after
OSD pop up
Check Field: On the color saturation of images all closed function
makes it a monochrome image
H/V delay: The image U/D, L/R flip
Image Flip: A line field blanking part optional switch
Camera :
Canon 5D II or similar camera when shooting, image
is not deformation, not black, without delay, perfect
without distortion
Menu page 2 picture
◆
Dot By Dot: In the video, the point to point display. Observing the
image more clearly
Reset: On system parameters and settings recover factory
settings
●
Scan adjust
Press "
, press "
" key, pop up OSD menu as below,"
" or "
" to confirm, With "
adjustment project, then use "
Press"
" or "
" to exit.
8
" or"
" or "
" to select
"button to choose
" to adjust or select the adjustment.
Horizontal Position: To adjust the image display(L/R)
Vertical Position: To adjust the image display(U/D)
Horizontal Size: To adjust the image L/R stretch
Vertical Size:
5.
To adjust the image U/D stretch
Signal format form
Signal format form
Video signal
Support signal format
Composite video
PAL/NTSC auto recognize
Component(Y/Pb/Pr)
1080/24p/24psf/25p/30p/50i/60i/50p/60p;
720/50p,720/60p; 480i、480p;576i、576p;
HDMI
1080/24p/24psf/25p/30p/50i/60i/50p/60p;
720/50p,720/60p; 480i、480p;576i、576p;
SDI(optional)
1080/24p/24psf/25p/30p/50i/60i/50p/60p;
720/50p,720/60p; 480i、480p;576i、576p;
DVI
Connect camera dedicated channels to avoid the
black screen
9
6.
SDI support mode
Serial No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Resolution
1080P@60HZ/59.94HZ
1080P@50HZ
1080I@60HZ/59.94HZ
1080I@50HZ
1080P@30HZ/29.97HZ
1080P@25HZ
1080P@24HZ
720P@60HZ/59.94HZ
720P@50HZ
720P@30HZ/29.97HZ
720P@25HZ
720P@24HZ/23.97HZ
480I@60HZ/59.94HZ
576I@50HZ
PAL
NTSC
Mode
Remark
3G
3G
HD
HD
HD
HD
HD
HD
HD
HD
HD
HD
SD
SD
SD
SD
7.
Power input way
●
Please use AC/CD adapter attached
●
When you use self-provided power supply, please reference above form to
connect electrical plug
◆ The monitor can also be supporting the battery plate mounted on the
battery power supply
10
Battery plate:
1. Sony V Mount Battery Plate(Standard)
2. Panasonic Anton Battery Plate(optional)
3. DV Battery Plate(optional)
Sony: F550/F570/F750/F770/F960/F970
Panasonic: D16S/D28S/D54S
Canon: BP930
8.
TALLY use and connect
TALLY Kit
11
●
TALLY use and connect
The use of random TALLY kit in accordance with the icon will be from the
switching station TALLY signal line connection
Connection method:
With power connect:Connect GND and G in short circuit grounding
R + and GND access 0-5 V voltage
When voltage is 0.3-2.7V, Tally green light normally on
When voltage is 2.8-5.5V, Tally red light flash.
Without power connect: Short circuit GND,R+,G, Tally red light flash.
● Please notice connection method
9.
Accessories
Sony V mount battery plate
Power adapter
BNC cable
TALLY kit
(for standard)
BNC to RCA Adapter SDI cable(optional) HDMI cable
Operation manual
Sony V mount battery plate(standard)
Power adapter
BNC cable
TALLY kit
BNC to RCA adapter
SDI cable(optional)
HDMI cable(HDMI to Mini HDMI)
Operation manual
1pc
1pc
1pc
1pc
3pcs
2pcs
1pc
1pc
12
10.Parameters
Panel size
12.1″ TFT LCD
Pixels
1280(H)×800(V)pixels
Distance
0.204(H)×0.0.204(V)mm
Brightness
200 cd/m²
Contrast ratio
500:1
Response time
16 ms
Display ratio
16:9 / 4:3 (adjustable)
Backlight
LED
Input voltage
DC7V-12V±10%
Input signal
3G-SDI, HD-SDI, SD-SDI, (Can choose)
HDMI, Component(Ypbpr), Composite Video, Audio
Output signal
3G-SDI, HD-SDI, SD-SDI, (Can choose)
Component(Ypbpr) Composite Video, Audio
Special function
TALLY,Image magnification,Image pause
Power consumption
≤ 8.5 W
Working temperature
-10℃~55℃
Storage temperature
-20℃~65℃
Size(mm)
300 L × 150 W × 70 .H (mm)
300 L × 275 W ×190 H (mm)
Weight
2520g
13
Folding
Stretch
11 .Trouble shooting
If there is any problem using the unit. You can try follow ways to
inspect and solve.
● Without image display
Trouble shooting
◆Video cable off or connect Check the quality of the cable, make sure the
incorrectly
correct input interface
◆ Without video signal input
Check the signal source and output interface
connect is correct or not
◆ Monitor is not be powered on Check the power whether connected, put the
power switch to “on”position
◆ Supply voltage instability
The power adapter or battery is poor
connected with battery plate
◆ The power use is self-made, Reference "Power input way" reconnect
polarity connect inversely
● Image/color display abnormal
Trouble shooting
◆ Video cable poor contact
Change video cable, try again
◆ Video signal interfered from
external environment
◆ Video input signal amplitude
too low
◆ Menu color saturation
adjustment closing
◆ B/W set in monochrome or
black & white
◆ Image deformation
Move to another environment to try again
Reset the ratio
● Speaker without sound
◆ Audio cable off or connect
improperly
◆ Volume adjustment was
closed
Trouble shooting
Confirm connected with the corresponding
input end
Reset the volume control is adjusted to a
proper position
Check signal source video output, or change
signal source have a try.
Enter menu check color, or reset to factory
settings
Press the B/W button, back to the color
◆ HDMI cable poor connected
Check the quality of cable, or chage cable
have a try
◆ No sound after switch video This monitor with audio signal only in audio
signal
input and HDMI
■ Remark:
If there are still other problems, please contact with our related deals
*If there are changes without prior notice.
14
">