Kirsch Panel Track Installation Instructions

Panel Track
Manual Operation Installation Instructions
GETTING STARTED
Mountin Types and Window Terminology.................................................................................................................. 1
Unpack the Box.............................................................................................................................................................. 1
Installation Components Required.............................................................................................................................. 1
Optional Components................................................................................................................................................... 3
Tools and Fasteners Needed......................................................................................................................................... 3
Product View — Panel Track......................................................................................................................................... 4
INSTALLATION
Inside and Ceiling Mount Applications........................................................................................................................ 5
Outside Mount Applications......................................................................................................................................... 6
Metal Box Valance Installation...................................................................................................................................... 7
Large Cassette Installation (Inside and Outside Mounts)......................................................................................... 8
Mount the Headrail........................................................................................................................................................ 9
Outside Mount Valance Installation (Optional)........................................................................................................ 11
Fabric Panel Installation.............................................................................................................................................. 12
Connect the Bottom Weights.................................................................................................................................... 17
Install the Room Divider Kit (Optional)..................................................................................................................... 18
OPERATION
Operate the Panels...................................................................................................................................................... 20
Adjustments.................................................................................................................................................................. 20
Troubleshooting........................................................................................................................................................... 25
CARE
Removal Procedures.................................................................................................................................................... 26
Cleaning Procedures.................................................................................................................................................... 28
CHILD SAFETY
Warning........................................................................................................................................................................ 29
Cord Loop Panels.......................................................................................................................................................... 29
WARRANTY................................................................................................................................................................... 30
Rev. A
9/1/20
GETTING STARTED
Thank you for purchasing Kirsch® Panel Track. With proper installation, operation, and care, your new unit will provide years
of beauty and performance. Please thoroughly review this instruction booklet and enclosed packing list before beginning the
installation.
Mounting Types and Window Terminology
If the installation brackets are mounted correctly, the rest of the installation process flows easily. To prepare for this important first
step, review the mounting types and basic window terminology illustrated below.
Molding
Head Jamb
Jamb
Jamb
Sill
Inside Mount
Shade fits within
window opening.
Collectively, the sill and
jambs are called the
“window casement.”
Outside Mount
Shade is mounted outside
window opening.
Unpack the Box
■ Carefully remove the rolled up fabric panels and set aside. Locate the panels marked “FRONT — INSTALL LAST” and “REAR —
INSTALL FIRST.” Set them aside, separated from the other panels. Do not unroll the panels until installation. Carefully remove
the headrail and optional valance from the packaging. Keep all packaging until the unit operates to your satisfaction.
■ Save these instructions for care and cleaning, panel removal, unit removal, and reinstallation procedures.
■ Check the Product View on page 4 to make sure you have all of the necessary parts. Contents of the hardware package may
vary depending upon how the unit was ordered and how it will be mounted.
Installation Components Required
Valance and Headrail Installation Brackets
Width
Brackets/Clips Required
28" – 32"
2
321⁄8" – 56"
3
56 ⁄8" – 80"
4
801⁄8" – 104"
5
104 ⁄8" – 128"
6
1281⁄8" – 152"
7
152 ⁄8" – 176"
8
1761⁄8" – 200"
9
1
1
1
■ Installation Brackets. This style of installation bracket is used for outside mounts. The number of installation brackets required
varies based on headrail width, as shown in the table above.
Installation Bracket
■ Mounting Clips. This style of mounting clip is used for inside mounts. The number of mounting clips required varies based on
headrail width, as shown in the table above.
Mounting
Clip
1
rge Round
Cassette
plice Cover
GETTING STARTED
■ Splice Clip. A splice clip allows a long headrail to be split in half during shipping, and reconnected during installation. Once
installed, a spliced headrail functions seamlessly as if it were one piece.
Splice
Clip
■ Valance Splice Clip. A splice clip allows a long valance to be split in half during shipping, and reconnected during installation.
Once installed, a spliced valance functions seamlessly as if it were one piece.
Valance Splice Clip
■ Large Cassette Installation Bracket. This style of installation bracket is used for Panel Track units ordered with the large
cassette. The brackets are used in both inside and outside mount applications. The number of installation brackets required
varies based on headrail width, as shown in the table below.
Cassette Installation Brackets Required
Shade Width
Brackets Required
Up to 36"
2
361⁄8" – 72"
3
721⁄8" – 90"
4
90 ⁄8" – 120"
5
1201⁄8" – 156"
6
1561⁄8" – 192"
8
1
Large Cassette
Installation Bracket
■ Large Cassette Splice Clip. This component is only provided with Panel Track units ordered specifically with a spliced headrail.
This clip joins two pieces of the cassette together. Once installed, a spliced cassette functions seamlessly as if it were one piece.
If you have not ordered the Panel Track unit with a spliced cassette, you will not receive this component.
Large Cassette
Splice Clip
■ Large Cassette Splice Cover. This is the decorative trim cover over the fabric seam in a spliced large cassette. It will also be
used when the fabric is seamed. The fabric seaming is sometimes necessary to obtain the full width of the cassette. In this case,
the splice cover will be installed by the fabricator. If you have not ordered the Panel Track unit with a large cassette, you will not
receive this component.
Large Square
Cassette
Splice Cover
■ Universal Cord Tensioner (UCT). The UCT functions as a safety device that makes the cords less accessible to children and pets
for those units with a cord control. The cord control will not function properly without the UCT installed correctly.
Universal Cord Tensioner
2
GETTING STARTED
Optional Components
■ Valance Brackets Inside Mount. The number of valance brackets will be the same as the number of installation brackets shown
in the table on page 2.
Valance Brackets
Inside Mount
■ Valance Brackets Outside Mount. The number of valance brackets will be the same as the number of installation brackets
shown in the table on page 2.
Valance Bracket
Outside Mount
■ Box Valance Brackets. A box valance wraps around the entire headrail. The number of valance brackets will be the same as the
number of installation brackets shown in the table on page 2.
Box Valance
Bracket
■ Room Divider Kit. This set of parts holds the panels in place at each end of a Panel Track unit used as a room divider.
Room Divider Kit
Tools and Fasteners Needed
■ Flat blade and Phillips screwdriver
■ Level (laser level is recommended)
■ Measuring tape and pencil
■ Needle nose pliers
■ Power drill and drill bits (1∕4" hex driver also recommended)
In addition, you will need fasteners designed to work with your specific mounting surface(s).
■ #6 Hex Head Screws (Provided). Two 11∕2" screws are provided per installation bracket.
■ Longer #6 Hex Head Screws (Not Provided). If using spacer blocks, use #6 screws long enough for a secure attachment.
#6 x 1½"
Hex Head Screw
(Provided)
Longer #6 Hex Head Screw
For Use With Spacer Blocks
(Not Provided)
3
GETTING STARTED
Product View — Panel Track
Installation
Bracket
Headrail Splice Clip
(Optional)
Headrail
Mounting Clip
Fabric
Panels
Single or Dual
Wand
Control
(Optional)
Operating
Cord
Universal Cord
Tensioner (UCT)
and Mounting
Bracket
Bottom
Weights
4
INSTALLATION
INSTALLATION
Inside and Ceiling Mount Applications
For panel order without a valance continue below. If you ordered a valance, see “Inside and Ceiling Mount Applications WITH A
Valance” on page 5.
Inside and Ceiling Mount Applications WITHOUT a Valance
■ Mark the mounting clip locations on the ceiling or inside the window casement. Use the figure below as a guide for locating the
mounting clips.
2"-4"
Jamb
18"-24"
18"-24"
18"-24"
2"-4"
Jamb
■ Use a 3∕32" drill bit to drill holes for the screws.
CAUTION: Do not mount into drywall, only mount into wood.
■ Use a level to check that the mounting surface is level. Shim the brackets if necessary. Shims are not provided.
■ Ensure the mounting clips are all facing the same direction.
Inside Mount (Standard)
➤ Standard Mount — The release tabs are toward to the window.
➤ Flush Mount — The release tabs are toward the room to allow for a flush
mounting.
Release Tab
Toward Wall
IMPORTANT: The mounting tabs will be visible on a flush mount unless concealed
by a valance.
■ Use the hex head screws provided to fasten the mounting clips to the mounting
Flush Mount Option
surface.
Ceiling/Top Sill
■ Verify that the mounting clips are mounted level and are aligned to each other.
Release Tab
Toward Room
For Closest
Wall Clearance
Wall
Room
Proceed to “Mount the Installation Brackets” on page 8.
Inside and Ceiling Mount Applications WITH A Valance
■ Refer to the appropriate section below for your valance type:
➤ Metal Valance with Returns — below.
➤ Metal Valance without Returns — page 5.
➤ Large Cassette — page 8.
➤ To mount your valance outside the window casement or to the wall — page 6.
IMPORTANT: The assembled valance serves as a drilling template when marking the screw holes on the sill or ceiling.
Metal Valance with Returns
■ Assemble the valance corners and returns.
Notches
➤ Fit the tabs on the corner end caps into the notches on the end of the valance piece.
Tabs
➤ Fit the tabs on the corner end cap into the notches on the end of the valance
return pieces.
■ Snap the valance brackets onto the valance, spacing them 2" to 4" from each end with
18" to 24" between intermediate valance brackets.
Valance Return
2"-4"
Jamb
18"-24"
Intermediate
Valance Brackets
Valance Clip Hole
18"-24"
18"-24"
Valance
Return
1
2"-4"
Jamb
■ Center the valance inside the window opening (inside mount) or over the window opening (ceiling mount).
5
2
Corner
End Cap
Valance
(Front of
the Unit)
INSTALLATION
INSTALLATION
■ Mark the drilling locations, using the valance clip holes as guides.
■ Set the valance aside.
■ Drill the holes at the mounting clip locations previously marked.
Valance Mounting
Bracket
CAUTION: Do not mount into drywall, only mount into wood.
■ Holding the valance in place over the drilled holes, insert a screw through each
mounting clip and valance bracket. Ensure that the RELEASE TAB FACES THE WALL.
Mounting Clip
Release Tab
Wall
Mounting
Screw
Room
Proceed to “Mount the Installation Brackets” on page 8.
Metal Valance without Returns
■ Snap the valance brackets onto the valance, spacing them 2" to 4" from each end with 18" to 24" between intermediate
valance brackets.
2"-4"
Jamb
18"-24"
Intermediate
Valance Brackets
Valance Clip Hole
18"-24"
18"-24"
2"-4"
Jamb
■ Center the valance inside the window opening (inside mount) or over the window opening (ceiling mount).
■ Mark the drilling locations, using the valance clip holes as guides.
■ Set the valance aside.
■ Drill the holes at the mounting clip locations previously marked.
Valance Mounting
Bracket
CAUTION: Do not mount into drywall, only mount into wood.
■ Holding the valance in place over the drilled holes insert a screw through each
mounting clip and valance bracket.
Mounting Clip
Release Tab
Wall
Mounting
Screw
Room
Proceed to “Mount the Installation Brackets” on page 8.
Outside Mount Applications
Installation Bracket Placement
■ Measure and mark the wall 2" to 4" in from each end of the headrail.
■ Evenly space and mark the intermediate installation brackets at 18" to 24" intervals along the headrail. DO NOT exceed 24"
between installation brackets.
Wall
2"-4"
18"-24"
18"-24"
18"-24"
2"-4"
End of Headrail Mark
CAUTION: The installation brackets must be mounted level to a flat, vertical surface for the unit to operate correctly. Do not
mount installation brackets on curved molding.
IMPORTANT: If your unit came with a spliced headrail, see “Spliced Headrails without Large Cassette” on page 15.
IMPORTANT: The top of the installation brackets need to be mounted at the outside mount ordered height plus an additional
½", for the desired floor clearance.
■ Use a 3∕32" drill bit to drill the screw holes.
CAUTION: Do not mount into drywall, only mount into wood.
6
INSTALLATION
INSTALLATION
■ Attach each installation bracket to the mounting surface using two screws.
Mounting Clip
■ Verify that the installation brackets are mounted level and aligned with each other.
2"
–4
"
A 2" minimum flat
vertical surface
is required to
mount the brackets.
End of
Headrail
Mark
Attach the Installation Bracket Covers
IMPORTANT: Bracket covers are optional and do not have to be installed.
■ Position the cover centered beneath the installation bracket.
■ Slide the cover up as far as possible.
■ Push against the cover to clip it onto the base of the installation bracket. The cover will snap over the
installation bracket base in two locations (against the back and at the top).
Proceed to “Mount the Installation Brackets” on page 8.
Metal Box Valance Installation
■ Refer to the appropriate section below for your valance type:
➤ Metal Box Valance — below.
➤ Large Cassette — page 8.
Metal Box Valance
■ Assemble the valance using two corners, one return piece, and the front and rear pieces. Do not put the other return and corner
pieces in place at this time.
IMPORTANT: The assembled valance serves as a drilling template when mounting the unit to the ceiling.
■ Install valance hanger clips inside box valance as shown.
■ Evenly space the intermediate valance box brackets at 18" to 24"
Release tab
positioned
away from
the valance.
intervals along the headrail. DO NOT exceed 24" between valance
brackets.
■ Slide the box valance brackets into the box valance as shown. Make sure
all of the release tabs on the installation brackets are positioned away
from the valance.
4"
2"-
■ Assemble the remaining return and two corner pieces and install them
onto the valance.
4"
"-2
18
■ Position the valance assembly where it will be mounted against
18
■ Drill the center hole (or near the center) first and install a screw.
CAUTION: Do not mount into drywall, only mount into wood.
■ Use a 3∕32" drill bit to drill the screw holes.
4"
"-2
4"
2"-
■ Install the rest of the box valance brackets and screws.
Proceed to “Mount the Installation Brackets” on page 8.
7
"
-24
the ceiling.
18
INSTALLATION
INSTALLATION
Large Cassette Installation (Inside and Outside Mounts)
Mount the Installation Brackets
Cassette Mounting Bracket
■ Bracket spacing is the same for inside and outside mounted panels.
■ Measure 2" in from where the ends of the cassette will be located and mark the
bracket locations on the mounting surface.
➤ If more than two installation brackets came with your order, make additional marks
to space the other bracket(s) evenly between the two end brackets.
Screw Holes for
Inside/Ceiling Mount
Mounting Holes for
Outside/Wall Mount
➤ The minimum mounting depth is 2¼". Fully recessed mounting depth is 4¼".
➤ Adjust bracket placement to gain clearance to avoid any obstructions, such as
window cranks or handles.
Front
Mounting Lip
Lower
Mounting Lip
Screwdriver Slot
for Removal
Cassette End Marks
2"
Space Evenly
Space Evenly
2"
Window Opening
■ Center an installation bracket on each mark. Then mark where to drill holes for the screws.
IMPORTANT: The installation brackets must be mounted level to operate properly.
■ Secure bracket with two screws.
Inside Mount
Outside Mount
2"
2"
Mount the Large Cassette
Choose the appropriate section below based on your panel:
Single Piece Cassettes
■ Angle the cassette back and then bring the cassette forward to catch the front lip of the
bracket.
Wall Installation
Bracket
Front Lip
■ Push the cassette back to snap it into the lower lip on the bracket.
Large Cassette
Snap into
Place
8
INSTALLATION
INSTALLATION
Spliced Cassettes
■ Angle each cassette section back and then bring the cassette forward to catch the front lip
Wall Installation Front Lip
Bracket
of the bracket.
■ Rotate the cassettes back to snap them into the lower lip on the bracket.
IMPORTANT: Make sure the sections are abutted together very tightly. The splice cover
(installed on the next page) will not cover large gaps between the sections.
Large Cassette
Snap into
Place
■ With the cassettes installed, center the large cassette splice clip over the joint, then insert it
into the upper track inside the cassette.
Cassette Splice Clip
■ Bow the clip and snap it into the track on the lower edge of the cassette.
■ Clip the large cassette splice cover over the fabric seam, clipping the bottom on first,
then snapping the top of the splice cover into place.
2
IMPORTANT: The splice cover will be used any time you need to cover a fabric seam.
This will be necessary when the cassette is spliced. It will also be used when the fabric
is seamed. The fabric seaming is sometimes necessary to obtain the full width of the
cassette. In this case, the splice cover will be installed by the fabricator.
Mount the Headrail
1
■ Refer to the appropriate section below for your order type:
➤ One Piece Headrail — below
➤ Spliced Headrails without Large Cassette — page 10
➤ Spliced Headrails with a Large Cassette — page 10
One Piece Headrail
Hook Lip
IMPORTANT: The headrail must be mounted level for the panels to operate correctly. Use
your level to check that the mounting clips are aligned and level.
■ Orient the headrail so that the control side is located on the correct side.
■ Center the headrail underneath the
Mounting
Clip
Headrail
mounting clips.
■ Starting with the center, tilt the headrail
and engage it under the lip of the mounting clips.
■ Rotate the headrail upward and snap it into place.
Snap into Place
■ Make sure the headrail is secure.
9
Room
INSTALLATION
INSTALLATION
Spliced Headrails without Large Cassette
Hook Lip
CAUTION: For spliced headrails, one person should hold each section.
■ Orient the headrail so that the control side is located on the correct side.
■ Mount the half with the attached headrail splice clip first.
■ Center the first section of headrail underneath the mounting clips.
Mounting
Clip
Headrail
Room
■ Starting with the center, tilt the headrail and engage it under the lip of the
mounting clips.
■ Rotate the headrail upward and snap it into place.
■ Make sure the headrail is secure, then align the second half of the headrail and abut
Snap into Place
it against the mounted half.
IMPORTANT: Ensure a mounting clip is adjacent to both sides of the splice on
the headrail.
■ Hook the front lip of the headrail splice clip onto the headrail.
■ Rotate the headrail upward to snap it into place.
Headrail Splice Clip Front Lip
First Hearail
Section
(Installed)
Room
Second Headrail Section
Spliced Headrails with a Large Cassette
CAUTION: For spliced headrails, one person should hold each section.
■ Orient the headrail so that the control side is located on the correct side.
■ Mount the half with the attached headrail splice clip first.
IMPORTANT: The headrail splice clip will need to be attached prior to installation into the
cassette, and the clip will need to be oriented with the release tab forward (into the room) as
shown.
■ Center the first section of headrail underneath the
Headrail
Splice Clip
Headrail
Release Tab
Wall
Room
Wall
mounting clips.
Release Tab
■ Starting with the center, tilt the headrail and engage it under the lip of the mounting clips.
■ Rotate the headrail upward and snap it into place.
■ Make sure the headrail is secure, then align the second half of the headrail and abut it against the
mounted half.
■ Important: Ensure a mounting clip is adjacent to both sides of the splice on the headrail.
■ Hook the front lip of the headrail splice clip onto the headrail.
■ Rotate the headrail upward to snap it into place.
Cassette
Wall
Room
Snap into
Place
10
INSTALLATION
INSTALLATION
Outside Mount Valance Installation (Optional)
Standard Metal Valance
■ Use the valance brackets provided and put them adjacent to the outside mounting brackets as shown.
Wall
Headrail
Valance Bracket
Installation Bracket
Release Tab
■ Ensure that the release tabs on the mounting clips, attached to the valance bracket, are facing
the wall as you snap them onto the headrail.
Engage
Lip
Snap
into
Place
CAUTION: Do not put valance returns on the valance before installing the valance.
■ Hold the valance up to the headrail.
Wall
■ Hook the upper clip of the valance into the upper tab of the valance bracket.
Room
Hook
Upper
Clip
Upper Tab
■ Snap the bottom of the valance into place in the lower clip.
■ Repeat for all valance brackets.
Wall
Room
■ Install the valance returns (if used):
Snap in
Bottom
Lower
Clip
Notches
Tabs
➤ Fit the tabs on the corner end cap into the notches on the end of the return.
Repeat with the other return.
➤ Carefully push the return and corner end cap into place on the valance.
Valance
Return
2
1
Corner
End Cap
Valance
(Front of
the Unit)
Attach the Universal Cord Tensioner (Cord Loop Units Only)
Before doing anything, you must first slide the cord tensioner to the bottom of the cord loop.
■ Insert a small screwdriver, punch, or awl through the screw hole at the bottom of the cord
tensioner.
■ Move the screw hole down to the indicator line to release the safety mechanism.
Universal
Cord
Tensioner
■ Slide the cord tensioner down to the bottom of the cord loop.
■ Attach the cord tensioner according to the instructions provided with the Universal Cord
Tensioner Installation Kit.
WARNING: It is imperative that the cord tensioner be properly secured to the wall or window frame to
reduce children’s access to the cord loop. Young children can strangle in cord loops. They can also wrap
cords around their necks and strangle.
Indicator
Line
CAUTION: The unit will not operate properly unless the cord tensioner is secured. A Universal Cord Tensioner Installation
Kit has been included with your unit. Follow the instructions in the kit to correctly secure the cord tensioner.
11
INSTALLATION
INSTALLATION
Fabric Panel Installation
■ There are six different Panel Track configurations available:
➤ Right Stack/Right Facing
➤ Right Stack/Left Facing
➤ Left Stack/Left Facing
➤ Left Stack/Right Facing
➤ Split Stack/Left Facing
➤ Split Stack/Right Facing
The “facing” direction, right or left, indicates the Panel Orientation.
Left Facing
Rear Panel
Right Facing
Front Panel
Front Panel
Rear Panel
The order of panel installation differs depending on the configuration selected. Refer to the label on the top of the headrail (see
figure below or your original order) to determine which configuration you ordered. In the figure below the “Panel Orientation = R”
means that this is a right facing unit.
In addition, the panels are available in 11½" and 17" widths, depending on the headrail width. The 17" panels have an additional
center guide to install in the headrail; 11½" panels have no center guide.
11 1⁄2" Fabric Hanger
17" Fabric Hanger
Center Guide
■ Refer to the appropriate page below based on your shade order:
➤ Right Stack/Right Facing or Left Stack/Right Facing — see below
➤ Left Stack/Left Facing or Right Stack/Left Facing — page 13
➤ Split Stack/Right Facing — page 14
➤ Split Stack/Left Facing — page 15
Right Stack/Right Facing or Left Stack/Right Facing Assembly
IMPORTANT: Use the wand or cord loop to traverse the unit open and closed to test for proper operation.
■ Use the cord loop or wand to traverse the carriers to the stacked position.
■ Manually stack the free carriers in the front channel to the right end. Reposition these as needed while installing each panel.
■ Locate the panel marked “REAR PANEL — INSTALL FIRST”. This is the first panel to install.
■ Locate the temporary plastic fabric hanger installed in the headrail. You will install the first panel into the same carriers.
Remember the carriers into which the hanger is installed, remove the temporary hanger. Twist it gently to remove.
12
INSTALLATION
INSTALLATION
■ With the front side of the rear panel facing you, insert the LEFT side of the fabric hanger into the carrier in the REAR channel
(see No. 1).
Front Channel
Rear Channel
Rear Carrier
1. Insert the left side of
the fabric hanger into
the rear carrier.
Center Screw
Channel
Front Carrier
Center Guide
2. Put the center guide into
3. Insert the right side of
the center channel
the fabric hanger into
(17" panels only).
the front carrier.
■ If you have 17" panels, slide the center guide into the center channel in the headrail (see No. 2).
■ Gently twist the fabric hanger inward and insert the RIGHT side of the fabric hanger into the carrier in the FRONT channel (see
No. 3).
IMPORTANT: After you have installed the first panel, verify that the flush end cap on the bottom weight is on the RIGHT side.
The flat side of the bottom weight should face the room.
Right Stack/Right Facing
Headrail (Top View)
Window
Bottom Weight
Room
Flush End Cap
■ Continue installing panels, rear channel first. The last panel you install will be marked “FRONT PANEL — INSTALL LAST.”
IMPORTANT: This panel has two flush end caps on the bottom weight.
■ Test traverse using the wand or cord loop.
Left Stack/Left Facing Assembly or Right Stack/Left Facing
IMPORTANT: Use the wand or cord loop to traverse the unit open and closed to test for proper operation.
■ Use the wand or cord loop to traverse the carriers to the stacked position.
■ Manually stack the free carriers in the front channel to the left end. Reposition these as needed while installing each panel.
■ Locate the panel marked “REAR PANEL — INSTALL FIRST”. This is the first panel to install.
■ Locate the temporary plastic fabric hanger installed in the headrail. You will install the first panel into the same carriers.
Remember the carriers into which the hanger is installed, remove the temporary hanger. Twist it gently to remove.
■ With the front side of the rear panel facing you, insert the RIGHT side of the fabric hanger into the carrier in the REAR channel
(see No. 1).
Front Channel
Rear Channel
Front
Screw
Carrier
Center
Channel
Rear Carrier
Center
Guide
3. Insert the left side of 2. Put the center guide
1. Insert the right side of
the fabric hanger into into the center channel
the fabric hanger into
(17" panels only).
the front carrier.
the rear carrier.
■ If you have 17" panels, slide the center guide into the center channel in the headrail (see No. 2).
13
INSTALLATION
INSTALLATION
■ Gently twist the fabric hanger outward and insert the LEFT side of the fabric hanger into the carrier in the FRONT channel (see
No. 3).
IMPORTANT: After you have installed the first panel, verify that the flush end cap on the bottom weight is on the LEFT side.
The flat side of the bottom weight should face the room.
Left Stack/Left Facing
Window
Bottom Weight
Flush End Cap
Headrail (Top View)
Room
■ Continue installing panels, rear channel first. The last panel you will install will be marked “FRONT PANEL — INSTALL LAST.”
IMPORTANT: This panel has two flush end caps on the bottom weight.
■ Test traverse using the wand or cord loop.
Split Stack/Right Facing
IMPORTANT: Use the wand or cord loop to traverse the unit open and closed to test for proper operation.
■ Use the wand or cord loop to traverse the carriers to the stacked position.
■ Manually stack the half of the free carriers in the front channel to the left end and the other half to the right end. Reposition
these carriers as needed while installing each panel.
■ Locate the panel (you had previously set aside) marked “REAR PANEL — INSTALL FIRST”. You will have one for the RIGHT side
and another for the LEFT side. This is the first panel to install.
■ Locate the temporary plastic fabric hanger installed in the headrail. You will install the first panel into the same carriers.
Remember the carriers into which the hanger is installed, remove the temporary hanger. Twist it gently to remove.
■ With the front side of the rear panel facing you, insert the LEFT side of the fabric hanger into the carrier in the REAR channel
(see No. 1).
Front Channel
Rear Channel
Rear Carrier
1. Insert the left side of
the fabric hanger into
the rear carrier.
Center Screw
Channel
Front Carrier
Center Guide
2. Put the center guide into
3. Insert the right side of
the center channel
the fabric hanger into
(17" panels only).
the front carrier.
■ If you have 17" panels, slide the center guide into the center channel in the headrail (see No. 2).
■ Gently twist the fabric hanger outward and insert the RIGHT side of the fabric hanger into the carrier in the FRONT channel
(see No. 3).
■ Important: After you have installed the first panel, verify that the flush end cap on the bottom weight is on the right side. The
flat side of the bottom weight should face the room.
Right Stack/Right Facing
Headrail (Top View)
Window
Bottom Weight
Room
Flush End Cap
■ Continue installing panels, rear channel first. The last panel you install will be marked “FRONT PANEL — INSTALL LAST”. You will
have one for the RIGHT side and another for the LEFT side.
IMPORTANT: This panel has two flush end caps on the bottom weight.
■ Test traverse using the wand or cord loop.
■ Continue with the stack on the left, and ensure the carriers have been traversed to the left, and the free carriers in the front
channel have been stacked to the left.
14
INSTALLATION
INSTALLATION
■ Locate the panel (you had previously set aside) marked “REAR PANEL — INSTALL FIRST”. You will have one for the RIGHT side
and another for the LEFT side. This is the first panel to install.
■ Locate the temporary plastic fabric hanger installed in the headrail. You will install the first panel into the same carriers.
Remember the carriers into which the hanger is installed, remove the temporary hanger. Twist it gently to remove.
■ With the front side of the rear panel facing you, insert the LEFT side of the fabric hanger into the carrier in the REAR channel
(see No. 1).
Left Stack/Right Facing
Front Channel
Rear Channel
Center
Channel
Rear
Carrier
1. Insert the left side of
the fabric hanger into
the rear carrier.
Front Carrier
Center
Guide
2. Put the center guide into
the center channel
(17" panels only).
3. Insert the right side of
the fabric hanger into
the front carrier.
■ If you have 17" panels, slide the center guide into the center channel in the headrail (see No. 2).
■ Gently twist the fabric hanger inward and insert the RIGHT side of the fabric hanger into the carrier in the FRONT channel
(see No. 3).
IMPORTANT: After you have installed the first panel, verify that the flush end cap on the bottom weight is on the LEFT side.
The flat side of the bottom weight should face the window.
Left Stack/Right Facing
Window
Bottom Weight
Flush End Cap
Headrail (Top View)
Room
■ Continue installing panels, REAR channel first. The last panel for the right stack will be marked “FRONT PANEL — INSTALL
LAST”. You will have one for the RIGHT side and another for the LEFT side.
IMPORTANT: This panel has two flush end caps on the bottom weight.
■ Test traverse using the wand or cord loop.
Split Stack/Left Facing
IMPORTANT: Use the wand or cord loop to traverse the unit open and closed to test for proper operation.
■ Use the wand or cord loop to traverse the carriers to the stacked position.
■ Manually stack the half of the free carriers in the front channel to the left end and the other half to the right end. Reposition
these carriers as needed while installing each panel.
■ Locate the panel marked “REAR PANEL — INSTALL FIRST”. You will have one for the RIGHT side and another for the LEFT side.
This is the first panel to install.
■ Locate the temporary plastic fabric hanger installed in the headrail. You will install the first panel into the same carriers.
Remember the carriers into which the hanger is installed, remove the temporary hanger. Twist it gently to remove.
15
INSTALLATION
INSTALLATION
■ With the front side of the rear panel facing you, insert the LEFT side of the fabric hanger into the carrier in the FRONT channel
(see No. 1).
■ If you have 17" panels, slide the center guide into the center channel in the headrail (see No. 2).
Right Stack/Left Facing
Front Channel
Rear Channel
Center
Channel
Front Carrier
Rear Carrier
Center
Guide
2. Put the center guide into
the center channel
(17" panels only).
1. Insert the left side of
the fabric hanger into
the front carrier.
3. Insert the right side of
the fabric hanger into
the rear carrier.
■ Gently twist the fabric hanger inward and insert the RIGHT side of the fabric hanger into the carrier in the REAR channel (see
No. 3).
IMPORTANT: After you have installed the first panel, verify that the flush end cap on the bottom weight is on the LEFT side.
The flat side of the bottom weight should face the window.
Right Stack/Left Facing
Window
Bottom Weight
Headrail (Top View)
Room
Flush End Cap
■ Continue installing panels, FRONT channel first. The last panel you install will be marked “FRONT PANEL — INSTALL LAST”. You
will have one for the RIGHT side and another for the LEFT side.
IMPORTANT: This panel has two flush end caps on the bottom weight.
■ Test traverse (use the wand or cord loop).
■ Continue with the stack on the right, and ensure the carriers have been traversed to the right, and the free carriers in the front
channel have been stacked to the right.
■ Locate the panel (you had previously set aside) marked “REAR PANEL — INSTALL FIRST”. You will have one for the RIGHT side
and another for the LEFT side. This is the first panel to install.
■ Locate the temporary plastic fabric hanger installed in the headrail. You will install the first panel into the same carriers.
Remember the carriers into which the hanger is installed, remove the temporary hanger. Twist it gently to remove.
■ With the front side of the rear panel facing you, insert the RIGHT side of the fabric hanger into the carrier in the REAR channel
(see No. 1).
Front Channel
Rear Channel
Front
Screw
Carrier
Center
Channel
Rear Carrier
Center
Guide
3. Insert the left side of 2. Put the center guide
1. Insert the right side of
the fabric hanger into into the center channel
the fabric hanger into
(17" panels only).
the front carrier.
the rear carrier.
■ If you have 17" panels, slide the center guide into the center channel in the headrail (see No. 2).
■ Gently twist the fabric hanger inward and insert the LEFT side of the fabric hanger into the carrier in the FRONT channel (see
No. 3).
16
INSTALLATION
INSTALLATION
IMPORTANT: After you have installed the first panel, verify that the flush end cap on the bottom weight is on the LEFT side.
The flat side of the bottom weight should face the room.
Left Stack/Left Facing
Window
Bottom Weight
Headrail (Top View)
Room
Flush End Cap
■ Continue installing panels, REAR channel first. The last panel you will install will be marked “FRONT PANEL — INSTALL LAST”.
You will have one for the RIGHT side and another for the LEFT side.
IMPORTANT: This panel has two flush end caps on the bottom weight.
■ Test traverse using the wand or cord loop.
Connect the Bottom Weights
■ Once you are satisfied with the operation, connect the bottom weights together. The bottom weights interconnect to stabilize
the panels. Each bottom weight has a snap slide on the back side, which connects to the adjacent bottom weight.
■ Use the wand or the cord loop to traverse the panels closed.
■ Starting at the back panel, push the snap slide of the next panel into the slot of the snap slide end cap of the back panel (behind
it). It should snap into place.
■ Progressing across the track, continue connecting the snap slide of each panel to the snap slide end cap of the panel behind it.
■ Once all panels have been connected, carefully check the operation of the track by traversing the panels open and closed.
■ If you experience any binding at the bottom, spray a small amount of silicone spray in the groove on the back of the bottom
weight.
Push Snap Slide
into Slot of Snap
Slide End Cap
Snap Slide
End Cap
Slot
Snap Slide
Rear View
17
INSTALLATION
INSTALLATION
Install the Room Divider Kit (Optional)
IMPORTANT: The floor bracket and snap slide can be mounted to the floor in a
position to hold the panels in directly beneath the headrail. Once mounted, the
snap slide is free to move up and down in its slot and can be attached to the last
moving panel. The wall plate and ball end cap keep the panel adjacent to the wall
in place.
Snap Slide
Wall Plate
Ball End Cap
Floor Bracket
Panel Adjacent to Wall
■ Locate the panel that will be adjacent to the wall.
Floor Bracket
■ Remove the end cap pin from the bottom weight.
End Cap Pin
■ Pull out the bottom weight flat end cap (next to the wall).
18
Wall
Plate
INSTALLATION
INSTALLATION
■ Install the ball end cap in the end of the bottom weight.
■ Reinstall the end cap pin.
■ Be sure the bottom weight is free hanging to determine where the ball end cap aligns
on the wall.
■ Align the wall plate with the ball end cap, and secure it to the wall with two #4 flat
head screws (and anchors if necessary).
■ Insert the ball end cap into the slot in the wall plate.
■ Insert the snap slide into the floor bracket by aligning the slot of the bracket with
the grooves in the snap slide. Be sure that the clip portion sits inside the slot of
the floor bracket. This will allow the snap slide to slip into the groove in the back
of the panel bottom weight if desired.
IMPORTANT: When the snap slide is snapped to the bottom weight, the panels
will only traverse the distance of one panel (see the figure on page 18). To
completely traverse the panels, disconnect the snap slide from the bottom
weight.
■ Determine where you want the floor bracket placed (somewhere along the first panel,
see the figure on page ).
■ Secure it in place with #6 flat head screws.
19
Clip Inside Bracket
INSTALLATION
OPERATION
Operate the Panels
Cord Loop Operation
■ Pull down on the FRONT cord
to stack the panels.
■ Pull down on the REAR cord to close the panels.
Wand Operation
■ Pull the wand toward the opposite side of the headrail to
stack the panels.
■ Pull the wand to the other side to close the panels.
Adjustments
Adjust the Cord Length
The length of the cord can be shortened to allow you to attach the Universal Cord Tensioner (UCT) in the desired position on the
wall.
■ Mount the UCT to the wall in the desired position. Refer to the UCT installation kit for instructions.
■ Pull each cord on the cord driver until you identify the one that does NOT move the carriers
when pulled. This is the cord that can be adjusted.
IMPORTANT: The end to shorten will be dotted with a black permanent marker (cannot be done
on cocoa or black cords).
IMPORTANT: Split stack panels have two cord drivers. You must locate the cord driver
WITHOUT the screw.
Dot
Cord Driver
Without Screw
20
Cord Driver
INSTALLATION
OPERATION
■ Using needle nose pliers, pull the cord knot from the cord driver (located in the headrail).
■ Pull out the cord until it is taut and the cord loop moves easily through the cord tensioner. If the cord is not taut, it will not
move through the cord tensioner.
■ Mark the top of the cord close to the cord driver (cannot be done on cocoa or black cords).
■ Remove the UCT from the bracket or wall.
■ Tie a double knot at the mark on the cord and let it retract into the cord driver.
■ Re-attach the UCT to the wall to ensure the cord is taut and cord loop moves easily through
the UCT. Repeat steps above to adjust further, if necessary.
■ Once the cord is adjusted, cut the excess cord below the knot hanging from the cord driver.
Adjust/Shorten Fabric Panel Length
CAUTION: Some units may not be able to reuse the plastic adhesive strip mentioned in this process. If the strip will not stick in
the new location, contact your Kirsch® dealer for a replacement.
■ Measure and record the amount you want to shorten on a panel. Refer to this information for any remaining panels you want
to shorten.
■ If the bottom weights were connected together, disconnect them.
■ Carefully remove the panel by releasing the fabric hanger from the carriers. See “Remove the Panels” on page 26.
■ Place the panel on a clean, flat working surface. If it is not possible to spread the panel out flat, then carefully roll the panel up
around the hanger (or preferably the shipping core), so that the bottom weight is accessible.
■ Use a small flat-blade screwdriver to remove the end cap pin in the bottom weight.
Snap Slide End Cap
■ Slide out the snap slide end cap from the bottom weight.
■ Slide the panel out of the bottom weight.
IMPORTANT: Note the folded flap at the bottom of the panel and how it is folded.
■ Unfold the fabric and carefully remove the plastic strip from the panel. Save it for
later use.
■ Holding the bottom end of the panel flat, mark the distance (previously recorded)
at several locations across the bottom of the panel. Using a straight-edge, draw a
line connecting these marks.
■ Using a sharp pair of scissors, carefully cut straight across each panel along the line
to remove the desired length from each panel.
■ Replace the previously removed plastic adhesive strip along the bottom of the
panel, aligning the strip with the bottom edge of the panel. Push on the plastic
adhesive strip so it adheres to the panel.
21
End Cap Pin
INSTALLATION
OPERATION
■ Carefully crease the panel along the upper edge of the strip.
IMPORTANT: Make sure there are no ripples in the fabric panel.
■ Holding the folded panel and plastic strip, carefully insert the panel into the
bottom weight until it is fully seated within the bottom weight.
CAUTION: Be careful NOT to pull on the fabric, as it can cause permanent
distortion or damage.
■ Re-install the snap slide end cap.
■ Insert the end cap pins back into in the bottom weight and press into place.
■ Reinstall the fabric panel into the headrail.
■ Repeat this process for the other panels.
■ Reconnect the bottom weights if required.
■ Using the wand or cord loop, traverse the shade open and closed to test for proper
operation.
Straighten Panel Fabric from Bottom Weight
If the panel fabric is creased or wrinkled at the bottom it can be adjusted and
straightened.
CAUTION: If the strip will not stick in the new location, contact your Kirsch designer for a replacement.
■ Use a small flat-blade screwdriver to remove the end cap pin in the bottom weight of
the affected panel.
Snap Slide
End Cap
■ Slide out the snap slide end cap from the bottom weight.
■ Slide the panel out of the bottom weight.
■ Check the fold and the position of the plastic adhesive strip.
■ To adjust, remove the plastic adhesive strip, adjust the fabric.
■ Reattach the plastic adhesive strip, aligning it with the exact edge of the panel.
22
End Cap Pin
INSTALLATION
OPERATION
■ Crease the fabric tightly along the strip.
Do not fold more than the width of the plastic adhesive strip.
■ Slide the panel back into the bottom weight, making sure the plastic adhesive strip fits
in the groove in the track.
■ Inspect the panel for folds or wrinkles.
■ Once satisfied with the adjustment, slide the snap slide end cap back into the end of
the bottom weight.
■ Insert the end cap pin back into place in the bottom weight and press to secure it.
Change the Control Side (For Wand-Control Panels)
IMPORTANT: While these instructions show the headrail not installed, the wand control side change can be done just as easily
with the unit fully installed.
■ Pull the wand sleeve down the wand to expose the metal J-hook.
Wand Sleeve
J-Hook
23
INSTALLATION
OPERATION
■ Disconnect the J-hook from the wand driver.
■ Connect the J-hook to the wand driver on the other side of the headrail.
Wand Driver
■ Slide the wand sleeve up the wand over the J-hook.
24
INSTALLATION
OPERATION
Troubleshooting
Problem How to determine unit panel orientation (whether it was made as right or left facing).
Solution The carriers in the headrail (where the panels hook in) will be WHITE for a right-facing headrail, and GRAY for a leftfacing headrail. Panels will fall out of the headrail if installed improperly from the purchased configuration.
Problem For cord loop panels only: the panel does not traverse or does not traverse easily.
Solution Check that the Universal Cord Tensioner is installed properly and the cord moves freely through it.
Check that the panel is installed correctly. The panels should be angled compared to the track, with each panel
hanger connected to a carrier in both the front and back channels.
Check that the bottom snap slides are installed correctly and operating correctly. The weights should slide together
easily when connected using the snap slide.
Check that the installation brackets are level, and the attached mounting clips are aligned.
Check that there are no obstructions to the movement of the panels, such as a cord caught in the brackets.
Lightly spray dry silicon lubricant inside the rail channels, as needed.
Problem The stack side is incorrect.
Solution Remove the panels and store flat on a clean surface. Reverse the headrail then re-install the headrail, panels, and
cord tensioner. Refer to the Universal Cord Tensioner Installation Instructions for cord tensioner installation. Lastly,
change the wand side if necessary.
IMPORTANT: Reversing the headrail will change the stack side only, not the panel orientation.
Problem An opaque fabric panel is wrinkled, creased or is rippling.
Solution Apply heat for 30 seconds with a hair dryer 6" away from the shade to release the creases, wrinkles or ripples in the fabric.
Problem The panel does not hang correctly.
Solution Check that the panel is installed correctly. Panels should be angled compared to the track, with each panel hanger
connected to a carrier in both the front and back channels.
Check that the headrail is level.
Check that the bottom weight snap slides are installed and operating correctly. The bottom weights should slide
together easily when connected using the snap slides.
Check that there are no obstructions to the movement of the panels.
Check that the Universal Cord Tensioner (if not wand control) is installed properly and that the cord does not
interfere with the hanging panel.
Wrinkling and folds in the panel fabric, due to packaging, will usually drop out within a few days. See “Straighten
Panel Fabric from Bottom Weight” on page 22, for adjustment, if necessary.
Problem For cord loop panels only: the Universal Cord Tensioner has climbed to the headrail.
Solution Pull down on the spring to relieve tension and pull the universal cord tensioner to the bottom of the cord loop.
Properly mount the cord tensioner. See “Attach the Universal Cord Tensioner (Cord Loop Units Only)” on page 11.
Problem For cord loop panels only: the UCT grabs onto the cord upon operation.
Solution Check that the Universal Cord Tensioner is mounted properly. Reinstall, if necessary.
Problem The panels are too long.
Solution See “Adjust/Shorten Fabric Panel Length” on page page 21.
25
INSTALLATION
CARE
Removal Procedures
Release the Universal Cord Tensioner
■ Remove the screw securing the Universal Cord Tensioner (UCT) to its installation bracket to release it.
Remove the Panels
■ Disconnect the bottom weights by gently pulling them apart.
■ Grasp the panel hanger on the sides.
■ Gently twist the panel hanger and pull downward to release the hooks from the carriers.
Right Facing/Right Stack Shown — All Others Are Similar
1. Gently Twist Panel
Hanger
Hanger
2. Pull Down to
Release Hooks
Remove the Optional Valance
Wall
Standard Valance
3 Remove
Top
Room
■ Release the bottom of the valance from the lower tab on the valance bracket by
pushing up on the tab.
■ Gently pull the bottom of the valance away from the installation bracket to
remove the valance from the upper tab.
Push Up on Tab 1
Remove the Headrail
Release 2
■ Locate the release tab on the mounting clip.
Mounting Clip
Release Tab
■ Firmly grasp the headrail.
■ Push up on the release tab to release the headrail. Repeat for each mounting clip.
■ Lift the headrail free from the mounting clips.
Push Up
on Tab
Headrail
Room
Remove
Headrail
Remove Panels with Large Cassette
One-Piece Headrail and Large Cassette
■ Insert the tip of a flat head screwdriver into the screwdriver slot provided on the bracket.
■ Press down to release the cassette.
Insert a
screwdriver
to release
the cassette.
26
INSTALLATION
CARE
■ Roll the cassette forward and then down to remove.
Wall
Installation Front Lip
Bracket
2 Release
Large Cassette
1 Pull
Spliced Headrail and Large Cassette
CAUTION: To avoid damage to the headrail and large fabric-covered cassette, one person should handle each section.
■ Locate the release tab on the mounting clips.
Wall
■ Firmly grasp the headrail.
Large Cassette
Release
Tab
■ Push up on the release tab to release the headrail. Repeat for each mounting clip.
■ Lift the headrail free from the mounting clips.
1 Push Release
Tab Up to
Release
2 Pull Headrail
Down
■ Insert the tip of a flat head screwdriver into the screwdriver slot provided on the bracket.
■ Press down to release the cassette.
Insert a
screwdriver
to release
the cassette.
■ Roll the cassette forward and then down to remove.
Wall
Installation Front Lip
Bracket
2 Release
1 Pull
27
Large Cassette
INSTALLATION
CARE
Cleaning Procedures
Dusting
■ Regular light dusting with a feather duster is all the cleaning that is needed in most circumstances.
Electrostatic Cleaning
■ Use a hand-held vacuum with low suction for more thorough dust removal.
Spot-Cleaning
■ Dampen a clean cloth with a solution of warm water and a mild detergent then wring it out.
■ Dab the spot with the dampened cloth until it is gone.
CAUTION: Keep all cleaning solutions away from the headrail system. Panel Track fabrics and headrail should never be
ultrasonically cleaned, injection/extraction cleaned, steam cleaned, or immersed in water.
CAUTION: Do not steam panels in an attempt to remove wrinkles or cupping.
Compressed Air or Hair Dryer
■ Use to blow dust off the panels. Use a hair dryer on a cool setting.
Standard Panel Track Metal Valance Cleaning
■ Wipe the valance with a damp cloth and a mild detergent solution.
Panel Track Large Cassette Cleaning
■ Follow the same directions above for the fabric panels.
Product Notes and Disclaimers
■ Actual fabric color may vary slightly from the samples. All variations are within established industry standards.
■ While opaque fabrics are blackout, due to the inherent light gaps between each panel, the application is room-darkening,
not blackout.
■ Fabrics that contain patterns, stripes or rows when hung as panels will create random alignment from panel to panel.
■ Many of the fabrics are fairly lightweight and will have varying levels of panel movement when installed near
air-conditioning vents or windows.
■ Depending on room conditions, wrinkles in product resulting from packaging should hang out.
■ The standard panel overlap will prevent most tangling of panels. Based on individual room conditions, some panel tangling
may occur.
28
INSTALLATION
CHILD SAFETY
WARNING
For more safety information, call 844-547-7742.
■ Window Blind Cord Can STRANGLE Your Child. Children can climb furniture to reach cords. Move crib and furniture away.
■ Keep all cords out of children’s reach.
Cord Loop Panels
■ Attach the cord tensioner on the cord loop to the wall or window casement. See “Attach the Universal Cord
Tensioner(s)” on page 11. This can prevent children from pulling cord loops around their necks.
■ Kirsch provides a cord tensioner installation kit with instructions for attaching the cord tensioner. For the
shade to operate properly, the cord tensioner must be correctly mounted and secured.
■ Fasteners provided in this kit may not be appropriate for all mounting surfaces. Use appropriate anchors
for the mounting surface conditions.
■ Only Kirsch supplied cord tensioners and hardware should be used. Replacement parts may be obtained by
contacting Kirsch Consumer Support at 844-KIRSCH2 (844-547-7742).
29
WARRANTY
Warranty
10-Year Limited Warranty
Kirsch® is proud to extend a 10-year limited warranty on all Kirsch Custom Window Covering products. This is part
of our commitment to providing the highest quality products, which has been our continued tradition since 1907.
COVERED
NOT COVERED
by a 10-Year
Limited Warranty
by a 10-Year
Limited Warranty
• Kirsch Custom Window Covering products are
covered for defects in materials, workmanship
or failure to operate for 10 years from the
date of purchase (unless a shorter period is
provided below), provided that the original retail
purchaser continues to own the product.
• Any conditions caused by normal wear and tear.
• Abuse, accidents, misuse or alterations to the
product.
• Exposure to the elements (sun damage, wind,
water/moisture, salt air) and discoloration or
fading over time.
• All internal mechanisms.
• Normal maintenance associated with motors
and related accessories including, but not limited
to, recharging and replacement of batteries.
• Fabric delamination.
• Components, brackets and operational cords.
• Repairs and/or replacements will be made with
like or similar parts or products. Fabric style, color
or components may vary depending on original
purchase date.
• Failure to follow our instructions with respect
to measurement, proper installation, cleaning
or maintenance.
• Shipping charges, cost of removal and
reinstallation.
• Kirsch automation components are covered for
5 years from the date of purchase.
Kirsch (or its licensed fabricator/distributor) will repair or replace the product or components found to be defective.
TO OBTAIN WARRANTY SERVICE:
• Contact your original dealer (place of purchase) for warranty assistance.
• Contact Kirsch at 844-KIRSCH2 (844-547-7242) for technical support, certain parts free of charge, for
assistance in obtaining warranty service or for further explanation of our warranty.
NOTE: In no event shall Kirsch or its licensed fabricator/distributor be liable or responsible for incidental or
consequential damages or for any other indirect damage, loss, cost or expense. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
© 2020 Kirsch Custom Window Coverings. All rights reserved. All trademarks used herein are the property of Kirsch or their respective owners. 09/20
30
">