Kirsch Alternative Woods Cordless Installation Instructions
Kirsch Alternative Woods Cordless are a stylish and functional option for window coverings. They combine the beauty of real wood with the convenience of a cordless design. With easy installation and simple operation, these blinds are perfect for any room in your home. The cordless operation also enhances child safety, eliminating the worry of dangling cords. Explore the features and instructions to discover the versatility and elegance of these blinds.
PDF
Download
Document
Advertisement
Advertisement
Alternative Wood Blinds Collection Cordless Installation Instructions GETTING STARTED Product View.................................................................................................................................................................. 1 Tools and Fasteners Needed......................................................................................................................................... 2 Unpack the Blind............................................................................................................................................................ 2 INSTALLATION Installation Overview..................................................................................................................................................... 2 Mount the Installation Brackets — Inside or Ceiling Mount..................................................................................... 3 Mount the Installation Brackets — Outside Mount................................................................................................... 4 Install the Blind............................................................................................................................................................... 6 Complete the Installation.............................................................................................................................................. 8 OPERATION Operate the Blind......................................................................................................................................................... 10 Troubleshooting........................................................................................................................................................... 10 CARE Removing the Blind (If Necessary)............................................................................................................................. 11 Cleaning Procedures.................................................................................................................................................... 11 CHILD SAFETY Cord Cleats.................................................................................................................................................................... 12 WARRANTY................................................................................................................................................................... 13 Rev. A 9/3/19 GETTING STARTED Product View End Bracket Spacer Block 1 Bracket Shim (Optional) Intermediate Bracket Spacer Block 1 End Bracket Intermediate Bracket (If Required) Valance End Bracket Spacer Block 1 End Bracket 2" or 4" Extension Brackets (Optional) Valance Splice (If Required) Hold-Down Brackets and Pin (Optional) Corner Clips for Valance Returns (If Required) Magnetic Valance Clips 1 Required with 21⁄2" slat size; optional 2" slat size. 1 GETTING STARTED Thank you for purchasing the Kirsch® Alternative Wood Blinds Collection. With proper installation, operation, and care, your new blinds will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation. Tools and Fasteners Needed ■■ 1⁄4" Hex and Flat blade screwdrivers ■■ Ballpoint pen ■■ Level (laser level is recommended) ■■ Measuring tape and pencil ■■ Power drill, 3⁄32" drill bit, and 1⁄4" hex driver (or socket wrench with 1⁄4" hex socket) In addition, you will need fasteners designed to work with your specific mounting surface(s). ■■ #6 Hex Head Screws (Provided). Two 11⁄2" screws are provided per installation bracket. ■■ Longer #6 Hex Head Screws (Not Provided). If using spacer blocks, use #6 screws long enough for a secure attachment. ■■ Speed Nuts and Screws (Provided). Extension brackets come with speed nuts and screws. ■■ Drywall Anchor (Not Provided). Use drywall anchors when mounting into drywall. #6 x 11∕2" Longer #6 Hex Head Screw Hex Head Screw for Use with Spacer Blocks (Provided) (Not Provided) Speed Nut and Screw (Two Provided with Each Extension Bracket) Unpack the Blind ■■ Remove the blind from the package. Keep the packaging until the blind operates to your satisfaction. ■■ Refer to the packing list and check for all necessary parts. ■■ Contents of your hardware package may vary depending upon the options chosen. ■■ Do not remove the slat protector tape (if applied). Doing so will damage the slat finish. ■■ Remove shipping protective piece in the headrail before installing (if applied). Remove Shipping Protective Piece Before Installing Top of Headrail Do Not Remove Slat Protector Tape INSTALLATION Installation Overview ■■ Two end brackets are used to mount alternative wood blinds. Wider blinds also require one or two intermediate brackets, as shown in the table below. Width of Blind Intermediate Brackets Up to 48" 0 48 ⁄ " – 60" 1 601⁄8" – 78" 2 18 End Bracket 2 Intermediate Bracket INSTALLATION INSTALLATION Mounting Types and Window Terminology If the installation brackets are mounted correctly, the rest of the installation process follows easily. To prepare for this important first step, review the mounting types and basic window terminology illustrated below. Molding Head Jamb Jamb Jamb Collectively, the sill and jambs are called the “window casement.” Sill Inside Mount Blind fits within window opening. Outside Mount Blind mounts outside window opening. ■■ Refer to the appropriate page below based on your order: ➤➤ Inside/Ceiling Mount — Below ➤➤ Outside Mount — Page 4 Mount the Installation Brackets — Inside or Ceiling Mount Bracket Shims (Optional) Bracket shims are used to gain clearance for valance clips with inside mounts. One shim for each end bracket and two shims for each intermediate bracket are included: One Shim One Shim Folded Over ■■ With each end bracket, first fold the shim and then position it on top of the end bracket to gain the required clearance. ■■ With each intermediate bracket, stack two unfolded Two Shims TwoStacked Shims Stacked Folded Over End End Bracket Bracket Intermediate Intermediate Bracket Bracket shims. NOTE: Bracket shims may also be used to level the blind whenever the mounting surface is uneven. The shims can be cut along their fold line to make them fit. Attach the End Brackets With inside or ceiling mounts, attach the two end brackets flush against the sides of the window casement or to the ceiling. Choose the most appropriate of the following mounting methods: ■■ Inside mount only (Side/Top Mount): Mount the end brackets with one screw through a side hole and one screw through a top hole, as shown in the first image to the right. ■■ Inside mount only (Side Mount): Mount the end brackets with two screws through diagonal side holes. ■■ Inside or ceiling mount (Top Mount): Top mount the end brackets with screws through the two top holes, as shown in the second image to the right. ■■ Ceiling mount only: If the end brackets are flush Side/Top Mount with the back wall, attach them with one screw through a top hole and one screw through a rear hole. 3 Top Mount INSTALLATION INSTALLATION ■■ Use a 3⁄32" drill bit to drill holes for the mounting screws. ■■ Attach the end brackets using the screws provided. IMPORTANT: The front edges of the end brackets must align. NOTE: For blinds with 21⁄2" slats, spacer blocks are used with inside mounts to position the end brackets a minimum of 3⁄8" away from the glass. The spacing prevents the slats from rubbing the glass when they are tilted open. Attach the Intermediate Brackets (If Required) ■■ Evenly space the intermediate bracket(s) between the two end brackets. ➤➤ Adjust spacing if needed to avoid Space Evenly End Bracket Intermediate Bracket Space Evenly End Bracket interference with internal headrail mechanisms. ■■ Attach the intermediate bracket(s) with two screws through diagonal top holes. IMPORTANT: The rear of the end brackets and intermediate bracket(s) must align. Proceed to “Install the Blind” on page 6. Mount the Installation Brackets — Outside Mount To attach the end brackets, a flat vertical surface of at least 13⁄4" is required for 2" and 21⁄2" slat sizes. Mark Mark the End Bracket Locations ■■ Mark where the ends of the headrail will be located. ➤➤ Center the headrail over the window opening at the desired height. Use a pencil to lightly mark each end of the headrail. ➤➤ Alternatively, measure the width of the headrail and use that Mark width to mark the headrail end points over the window opening. ■■ Make a second mark 1⁄4" to the outside of the headrail end marks. The outer marks are where the outside edges of the end brackets will be located. Measure and Mark 1/4" Out from Ends of Headrail Attach the End Brackets NOTE: The illustrations in this section show spacer blocks mounted with the end brackets for the 2" and 21⁄2" slat sizes. Spacer blocks are required for all outside mount 21⁄2" blinds, unless extension brackets are used. Spacer blocks are optional for 2" slat sizes. ■■ Align the outside edge of each end bracket with the outer marks and mark diagonal screw holes. ➤➤ Use a 3⁄32" drill bit to drill holes for the mounting screws. ■■ Attach the end brackets using the two screws through diagonal holes. ➤➤ If using spacer blocks, use #6 screws long enough for a secure installation (21⁄2" long screw recommended). IMPORTANT: The tops of the end brackets must align. CAUTION: The rear of the end brackets or spacer blocks must be flush against a flat mounting surface. Do not mount end brackets on a curved molding. 4 INSTALLATION INSTALLATION Attach the Intermediate Brackets (If Required) ■■ Evenly space the intermediate bracket(s) End Bracket between the tow end brackets. Intermediate Bracket ➤➤ Adjust spacing if needed to avoid Space Evenly End Bracket Space Evenly interference with internal headrail mechanisms. ■■ Attach the intermediate bracket(s) with two screws through diagonal holes. IMPORTANT: The tops of the end brackets and intermediate bracket(s) must align. 13∕8", 2", and 21∕2" Slat Sizes Extension Brackets (Optional) Attach 2" or 4" extension brackets to the mounting surface in the same locations where the end brackets would be attached. ■■ Use the provided screws to mount each extension bracket. IMPORTANT: The tops of the end brackets and intermediate bracket(s) must align. ■■ Attach the installation brackets to the extension brackets using the screws and not provided, as shown below. End Bracket with 2" Extension Bracket Intermediate Bracket with 2" Extension Bracket End and Intermediate Brackets with 4" Extension Bracket Spacer Blocks 21⁄2" Slat Size 1 ∕8" Slat Size NOTE: Spacer blocks are required for the 21⁄2" slat size and are optional for 2" slat sizes. 3 End Bracket ■■ Attach a spacer block to each of the two end brackets. ■■ If one or more intermediate brackets is required (see chart on page 2), attach a spacer block to each intermediate bracket. ■■ If extension brackets will be used, it is not necessary to attach spacer blocks. End Bracket with 2" Extension Bracket Intermediate Bracket with 2" Extension Bracket Proceed to “Install the Blind” on page 6. 5 Intermediate Bracket End and Intermediate Brackets with 4" Extension Bracket INSTALLATION INSTALLATION Install the Blind Attach the Magnetic Valance Clips to the Valance The magnetic valance clips are adjustable for quick and easy valance attachment and have multi-position valance adjustment capabilities. ■■ To install the clips, lay the valance face down on a protected surface with the back side up. ■■ Insert the clip dovetail into the valance groove. ■■ Twist the clip until it is straight with the clear tabs at the top of the valance. ➤➤ There are at least two clips per valance. For valances narrower than 36", position clips 51⁄2" in from the ends of the valance. For valances 36" or wider, position the clips 10" in from the ends of the valance. Additional clips should be spaced evenly between the two end clips. Adding Projection for the Valance The magnetic valance clips have a projection adjustment feature. By pulling the clips outward, the clips can provide an additional 1⁄4" projections. ■■ Remove the clips from the valance. ■■ Insert a small flat blade screwdriver into the slot on one side of the magnet making sure the screwdriver is all the way down in the slot. ■■ Push the screwdriver in toward the magnet and then pull out to extend the clip. ■■ Repeat on the other side until the magnet is level. ■■ When the clips are in the correct position, place them back into the valance groove. ■■ The clips offer two projection positions. When the clips are fully compressed, the narrowest projection is 5⁄8". The widest projection is 7⁄8". ∕8" 5 Narrow Projection 6 ∕8" 7 Wide Projection INSTALLATION INSTALLATION Mount the Headrail ■■ Tilt the headrail so that its back lip slides under the front lip of the end brackets and intermediate bracket(s). ■■ Push the headrail against the back of the end brackets. ■■ Check that the front lip of the intermediate bracket(s) is under the front lip of the headrail. Adjust the Headrail Tightness End Bracket Intermediate Bracket ■■ If the headrail is loose in the end brackets, bend the tabs on the end bracket outward. NOTE: The tabs may also be bent inward if the headrail is difficult to install into the end brackets. ■■ If your headrail end brackets do not have adjustable tabs, bend the tabs on the headrail end locks to adjust headrail tightness. Close the End Brackets ■■ Push the cover down until it snaps over the locking tab on the bottom of the end bracket. Open the End Brackets (If Necessary) ■■ To open the end brackets, insert a flat blade screwdriver between the bottom of the cover and the quick release tab, and twist. ➤➤ You can also push up on the bottom of the end bracket to release the locking tab. Proceed to “Complete the Installation” on page 8. 7 13∕8" Slat Siz INSTALLATION INSTALLATION Complete the Installation Attach the Wand (If Ordered) If the blind was ordered with a wand tilter, attach the wand to the metal shaft. NOTE: Wands may appear different from the illustration, but assembly is the same. ■■ Pull the plastic sleeve from the top of the wand and insert it over the metal shaft. ■■ Insert the hook on the wand through the hole in the metal shaft. ■■ Slide the plastic sleeve down over the hook until firmly seated. ■■ Test the wand tilter. Approximately six revolutions of the wand should tilt the slats from fully closed up to fully closed down. Metal Shaft Plastic Sleeve Hook Wand Slide Sleeve Over Shaft Hook Through Hole Slide Sleeve Over Hook Attach the Corner Clips (If Required) If the valance came with returns, connect the returns to the valance using the corner clips provided. ■■ The notches on the rear of the valance and returns fit into the grooves of the corner clips. Miters Meet Valance Notch ■■ Slide one end of each clip onto the rear of the valance until the center of the clip aligns with Valance Return (CrossSection) the edge of the miter cut at each end. ■■ Slide a return onto each corner clip until its miter is flush against the miter on the valance. Notch Corner Clip Attach the Valance Splice (If Required) For valances that are spliced, join the two mitered valance pieces together by sliding the valance splice clip over the back of the valance where the two halves meet. Miters Valance Splice Clip 8 INSTALLATION INSTALLATION Attach the Valance with Magnetic Valance Clips ■■ Align the valance to the headrail. ■■ Hold the valance securely from the front side with both hands. ■■ Position the clips to the top-front lip of the headrail until it is level and in position. ■■ Press the valance gently forward, just enough so the clips adhere to the headrail. ■■ Adjust the valance projection: ➤➤ Inside Mount: Press the valance forward until the face is flush with the opening or the clips are attached to the headrail. ➤➤ Outside Mount: Press the valance forward until the clips are attached to the headrail. To minimize the gap between the valance return and the wall, follow the clip projection adjustment instructions on page 6. ■■ The magnetic valance clips allow for limited valance height adjustments by carefully sliding the clip up or down while the magnets are adhered to the headrail. The clip’s tabs rest on the top-front lip of the headrail, keeping the valance level and preventing the valance from adjusting lower beyond that point. ■■ To remove the valance, gently pull the valance up and toward you. CAUTION: The entire surface area of the magnet inside each clip needs to maintain clean contact with the front surface area of the headrail at all times. Attach the Hold-Down Brackets (Optional) ■■ For alternative wood bottom rails, the bottom rail will come with pre-drilled 3⁄32" holes and hold-down pins that have been inserted in the center of the bottom rail end. ■■ To mount the hold-down brackets, first fully lower the blind. Align the hold-down brackets with the hold-down pins in the bottom rail. ➤➤ Align the first slot with the 21⁄2" slat size. ➤➤ Align the second slot with the 2" slat size. ■■ Maintain the correct slot alignment as you attach the hold-down brackets to the jamb, sill, or outside mounting surface. First Slot Second Slot Jamb Mount Sill Mount Outside Mount ■■ Slide the hold-down pins into the appropriate slot or hole on the hold-down brackets. ■■ If necessary with 2" outside mount blinds, the first slot of the hold-down brackets may be used in place of a spacer block. 9 INSTALLATION OPERATION Operate the Blind Tilting the Slats ■■ Wand tilt: Rotate the wand to tilt the slats to the desired angle. ■■ Cord tilt: The two cords with individual tassels are for tilting the slats. Each cord tilts the slat in an alternate directions. Raising and Lowering the Blinds IMPORTANT: Whenever raising or lowering the blind, the slats must be in the open position. ■■ Grasp the bottom rail and push up to raise the blind. ■■ Grasp the bottom rail and pull down to lower the blind. Troubleshooting Problem The blind will not fit into the installation brackets. Solution Check that the installation brackets are level and aligned. Adjust and/or shim to level, if necessary. Be sure the heads of the screws are flush against the installation brackets. Check that the headrail is completely inserted into the installation brackets. See “Mount the Headrail” on page 7. Problem The blind does not tilt. Solution Check that the tilt cords are not tangled or knotted. Check that the ladders have not become disengaged from the tape rolls. Check that the tilt rod is fully inserted into the tilt gear. Problem The blind does not raise or lower evenly. Solution Check inside the headrail. Make sure no obstructions keep the mechanism from turning. Check that the lift cords are not pinched or tangled. 10 INSTALLATION CARE Removing the Blind (If Necessary) ■■ Fully raise the blind. ■■ To remove the valance with magnetic valance clips, see page 6. ■■ Push up on the bottom end of the bracket to release the locking tab. ■■ Grab underneath the headrail using both hands and carefully pull the blind out of the end brackets. Cleaning Procedures Like any fine furnishings, Kirsch® Alternative Wood Blinds Collection should be cleaned regularly to keep them looking new. Dusting ■■ Dust regularly. Use a soft clean cloth, chemically-treated dust cloth, or dusting mitt. Lower the blind until it is full length, tilt the slats almost all the way down, and dust. Then tilt the slats almost all the way up and dust. (Not closing the slats all the way allows dusting where the slats overlap.) ■■ Blinds may also be vacuumed. Use the brush attachment and tilt the slats up and down as described for dusting. ■■ Another way to clean blinds is simply by wiping them with a soft, damp cloth. Cleaning ■■ Wash the slats only using a non-abrasive mild detergent solution. Allow to air dry preserve the dust repellent properties of the slats. ■■ For a more thorough cleanings, alternative wood bottom rails and slats may be immersed in a bathtub. Bathtub cleaning is not recommended for blinds with decorative tapes. Do not immerse headrail. IMPORTANT: Kirsch does not recommend ultrasonic cleaning of alternative wood blinds. 11 INSTALLATION CHILD SAFETY WARNING For more safety information, call 1-800-997-2389. ■■ Window Blind Cord Can STRANGLE Your Child. ■■ Children can climb furniture to reach cords. Move crib and furniture away. ■■ Keep all cords out of children’s reach. Cord Cleats Kirsch® offers cord cleats and recommend their use. ■■ Attach two cord cleats 6” to 12” apart at a height where they will be out of the reach of children. Take into account that a child may stand on furniture attempting to reach the cords. Be sure the cleats are firmly secured. ■■ Once the cleats are attached, wrap excess cord around them after each use of the blind. NOTE: The warning labels on the bottom rails of corded blinds contain important safety information. These warning labels are designed to be permanent, in accordance with the industry’s safety standards, and must not be removed. 12 WARRANTY Warranty 10-Year Limited Warranty Kirsch® is proud to extend a 10-year limited warranty on all Kirsch Custom Window Covering products. This is part of our commitment to providing the highest quality products, which has been our continued tradition since 1907. COVERED NOT COVERED by a 10-Year Limited Warranty by a 10-Year Limited Warranty • Kirsch Custom Window Covering products are covered for defects in materials, workmanship or failure to operate for 10 years from the date of purchase (unless a shorter period is provided below), provided that the original retail purchaser continues to own the product. • Any conditions caused by normal wear and tear. • Abuse, accidents, misuse or alterations to the product. • Exposure to the elements (sun damage, wind, water/moisture, salt air) and discoloration or fading over time. • All internal mechanisms. • Normal maintenance associated with motors and related accessories including, but not limited to, recharging and replacement of batteries. • Fabric delamination. • Components, brackets and operational cords. • Repairs and/or replacements will be made with like or similar parts or products. Fabric style, color or components may vary depending on original purchase date. • Failure to follow our instructions with respect to measurement, proper installation, cleaning or maintenance. • Shipping charges, cost of removal and reinstallation. • Kirsch automation components are covered for 5 years from the date of purchase. Kirsch (or its licensed fabricator/distributor) will repair or replace the product or components found to be defective. TO OBTAIN WARRANTY SERVICE: • Contact your original dealer (place of purchase) for warranty assistance. • Contact Kirsch at 844-KIRSCH2 (844-547-7242) for technical support, certain parts free of charge, for assistance in obtaining warranty service or for further explanation of our warranty. NOTE: In no event shall Kirsch or its licensed fabricator/distributor be liable or responsible for incidental or consequential damages or for any other indirect damage, loss, cost or expense. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. © 2019 Kirsch Custom Window Coverings. All rights reserved. All trademarks used herein are the property of Kirsch or their respective owners. 09/19 13 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Cordless operation
- Alternative wood slats
- Easy installation
- Magnetic valance clips
- Adjustable valance projection
- Child-safe design
- Multiple mounting options
Frequently asked questions
You can adjust the valance projection by pulling out the magnetic valance clips. This allows for a 1⁄4" increase in projection, providing options for different aesthetic looks.
First, fully lower the blind. Align the hold-down brackets with the hold-down pins in the bottom rail. Slide the hold-down pins into the appropriate slot or hole on the hold-down brackets.
Dust regularly using a soft, clean cloth. For a more thorough cleaning, alternative wood bottom rails and slats may be immersed in a bathtub. Do not immerse the headrail.