Vortech Mustang GT supercharger system Installation instructions
Below you will find brief information for supercharger system Mustang GT. This document is a comprehensive guide that covers installation, maintenance, and service of the Vortech supercharger kit specifically designed for the 2015-2016 Ford Mustang GT. The manual includes detailed illustrations, specifications, and procedures for a smooth installation process.
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
Mustang
Installa tion Instr
Model
GT uctions
Year*
*Not legal for highway use.
®
ENGINEERING, INC
1650 Pacific Avenue, Channel Islands CA 93033-9901 • Phone: 805 247-0226
Fax: 805 247-0669 • www.vortechsuperchargers.com
i
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
FOREWORD
T his manual provides information on the installation, maintenance and service of the
Vortech supercharger kit expressly designed for this vehicle. All information, illustrations and specifications contained herein are based on the latest product information available at the time of this publication. Changes to the manual may be made at any time without notice. Contact Vortech Engineering for any additional information regarding this kit and any of these modifications at (805) 247-0226 7:00am-3:30pm PST.
Take note of the following before proceeding:
1. Proper installation of this supercharger kit requires general automotive mechanic knowledge and experience. Please browse through each step of this instruction manual prior to beginning the installation to determine if you should refer the job to a professional installer/technician. Please contact your dealer or Vortech Engineering for possible installers in your area.
2. This product was designed for use on stock (un-modified, OEM) vehicles. The PCM
(computer), engine, transmission, drive axle ratios and tire O.D. must be stock. If the vehicle or engine has been modified in any way, check with Vortech prior to installation and use of this product.
3. Use only premium grade fuel with a minimum of 91 octane (R+M/2).
4. Always listen for any sign of detonation (knocking/pinging) and discontinue hard use
(no boost) until problem is resolved.
5. Vortech is not responsible for any clutch, transmission, drive-line or engine damage.
Exclusions from Vortech warranty coverage considerations include, but not limited to:
1. Neglect, abuse, lack of maintenance, abnormal operation or improper installation.
2. Continued operation with an impaired vehicle or sub-system.
3. The combined use of Vortech components with other modifications such as, but not limited to, exhaust headers, aftermarket camshafts, nitrous oxide, third party PCM programming or other such changes.
©2016 VORTECH ENGINEERING, INC
All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, or translated
into another language in any form, by any means without written permission of Vortech Engineering, Inc.
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured ii
TABLE OF CONTENTS
FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
TABLE OF CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
IMPORTANT NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
TOOL & SUPPLY REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
PARTS LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
1. BASIC COMPONENT REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. MISCELLANEOUS PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3. SUPERCHARGER ASSEMBLY PREPARATION & INSTALLATION. . . . . . . . . . . . . . . . . . . . .7
3.1 MOUNTING BRACKET ASSEMBLY DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 BELT ROUTING DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4. PCV SYSTEM MODIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5. CHARGE AIR COOLER (CAC) & DISCHARGE TUBE INSTALLATION. . . . . . . . . . . . . . . . . 14
6. FUEL INJECTOR REPLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7. ENGINE COOLING SYSTEM MODIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8. AIR INLET ASSEMBLY INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8.1 VACUUM ROUTING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9. BYPASS VALVE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10. MISCELLANEOUS REASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
11. OIL FEED INSTALLATION (OIL-FED UNITS ONLY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
12. OIL DRAIN INSTALLATION (OIL-FED UNITS ONLY). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
13. REFLASH COMPUTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
14. FINAL CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
iii
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
NOTICE
This product is protected by state common law, copyright and/or patent.
All legal rights therein are reserved. The design, layout, dimensions, geometry, and engineering features shown in this product are the exclusive property of Vortech Engineering, Inc. This product may not be copied or duplicated in whole or part, abstractly or fundamentally, intentionally or fortuitously, nor shall any design, dimension, or other information be incorporated into any product or apparatus without prior written consent of Vortech Engineering, Inc.
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured iv
2015 Ford Mustang GT
Installation Instructions
Congratulations on selecting the best performing and best backed automotive supercharger available today... the VORTECH® supercharger!
Before beginning this installation, please read through this entire instruction booklet and the Street
Supercharger System Owner’s Manual which includes the Limited Warranty Program, the Warranty
Registration form and return envelope.
Vortech supercharger systems are performance improving devices. In most cases, increases in torque of 30-35% and horsepower between 35-45% can be expected with the boost levels specified by Vortech Engineering. This product is intended for use on healthy, well maintained engines.
Installation on a worn-out or damaged engine is not recommended and may result in failure of the engine as well as the supercharger. Vortech Engineering is not responsible for engine damage.
Installation on new vehicles will not harm or adversely affect the break-in period so long as factory break-in procedures are followed.
For best performance and continued durability, please take note of the following key points:
your vehicle. Thereafter, always use a high grade SF rated engine oil or a high quality synthetic, and change the oil and filter at least every 3,000 miles. Never attempt to extend the oil change interval beyond 3,000 miles, regardless of oil manufacturer’s claims as potential damage to the supercharger may result.
miles with original heat range plugs as specified by the manufacturer and reset timing to factory specifications (follow the procedures indicated within the factory repair manual and/
TOOL & SUPPLY REQUIREMENTS
• Factory repair manual
• 3/8" socket and drive set: SAE & metric
• 1/2" socket and drive set: SAE & metric
• Adjustable wrench
• Open end wrenches: metric
• TORX T-20 driver
• Utility knife
• Oil-Fed Kits: 3/8" NPT tap, center punch, 5/8" tapered punch, heavy grease,
8 quarts manufacturer-specified engine oil, oil filter, oil filter wrench
If it has been 35,000 miles or more since your vehicle’s last spark plug change, then you will also need:
• Spark plug socket
• NEW spark plugs
v
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
®
ENGINEERING, INC
2015 Ford Mustang GT, H.O.
Part No. 4FQ218-064L
PARTS LIST
IMPORTANT: Before beginning installation, verify that all parts are included in the kit. Report any shortages or damaged parts immediately.
PART NUMBER DESCRIPTION QTY. PART NUMBER DESCRIPTION QTY.
008110
008130
008447
009035
DECAL, VINYL, VORTECH 2
LICENSE PLATE FRAME, VORTECH 1
1 YR S/C WARRANTY PKG 1
S/C LUBE, BOTTLED, 3-PACK 1
2F329-214 S/C ASSEMBLY, 2015 MUSTANG GT 1
4FQ020-015 INSTR.MAN.,'15 FORD MUSTANG GT 1
4FQ111-013 MNTG BRKT ASY, G2, 2015 MUST 1
2A017-875-27 SPACER, .875OD X .404ID X 1.895L
2A017-875-28 SPACER, .875 OD X 2.730 LONG
2A017-876-13 SPACER, .875OD X .328ID X 2.730L
2A017-876-14 SPACER, .875OD X .328ID X 2.058L
2A017-876-15 SPACER, .875OD X .328ID X 2.146L
4
1
2A017-876-16 SPACER, .875OD X .328ID X 1.928L
2A046-031 BELT, 6 RIB X 103.31 EFF. LENGTH
4FQ010-011 MNTG PLT, OUTER, 2011 MSTG 5.0
4FQ010-021 MNTG PLT, INNER, 2011 MSTG 5.0
4FQ017-021 SPCR, .875/1.25OD X .328ID X 1.782L
4FQ017-031 SPCR, .875ODX.404IDX.363L W/.66 PLT 4
4GF016-161 PULLEY, 3" IDLER, GROOVED, MOD
4PCS016-160 PULLEY, IDLER, SRT10 TRUCK
4TX016-150 IDLER, 2.75 DIA, SMOOTH, 7 RIB
7A375-126
7A375-352
7C080-064
7C080-081
7C080-101
3/8-16 X 1.25 HHCS, GR8, PLT
3/8-16 X 3.5" HX HD GR8
M8 X 1.25 X 65MM BHCS CL10.9
M8 X 1.25 X 80 HXHD CL10.9
M8-1.25 X 100 BHCS CL10.9
7C080-200 M8-1.25 X 200MM STUD, 35MM THREAD 2
7F008-021
7J312-000
7K375-040
7K375-050
NUT, M8 X 1.25, SERRATED FLG
5/16 FLAT WASHER-SAE
3/8 AN960 FLAT WASHR PLATED
3/8 WASHER, STAINLS, .030THK
9
1
2
3
1
1
5
1
2
5
1
1
1
1
1
1
1
1
2
2
4FQ112-110 AIR INLET ASSY, '15 MUSTANG GT 1
008358 DECAL, INLET, 2011 MSTG GT VORT
4FQ012-110 AIR INLET DUCT, 2015 MUSTANG
5W001-039 1" HEAT SHRINK TUBING
5W001-082 SLEEVE, FLEX BRAID 0.75" NOM.
7C040-008
7J006-093
7P375-039
7P375-098
M4-.7X8MM SCHD SS
6MM WASHER, PLATED
3/8 NPT X 5/8 BARB 90°
TEE, 3/8" INCH, PLASTIC
1
1
3
.75
7P375-106 PCV VALVE, FORD 3/8" HOSE 1
7P375-378 VALVE, CHECK, 3/8 BARB X 3/8 BARB 1
1
1
1
1
1
1
2
2
7P625-004
7P625-091
7P625-375 REDUCER, 5/8 BARB TO 3/8 BARB
7P625-377
7PS400-200
5/8 TEE #28634
5/8 X 5/8 90° BARB ELBOW, PL
5/8-3/8 REDUCER BARB UNION
7PS375-100 SLEEVE, 3.75 X 1.0 3-PLY MATTE BLK 1
SLEEVE, BLACK 4.0D X 2.0
7PS400-225 BUMP SLEEVE, 4.0 X 2.25, BLACK
7PS400-351 REDUCER SLEEVE, 4.0 X 3.5 X 2.35L
7R002-052 352 SAE TYPE F SS HOSE CLAMP
7R002-064
7R004-002
#64 SAE TYPE F SS HOSE CLAMP
STEPLESS CLAMP, 17.0-70
1
1
1
1
4
6
7R004-004 STEPLESS CLAMP, 25.6 X 7MM WIDE 10
7R004-007 STEPLESS CLAMP, 28.6 X 7MM WIDE 2
7U030-056
7U033-000
7U100-055
3/8 PCV/VAC RUBBER HOSE
5/8 PCV HOSE
2
2.5
TIE WRAP, 7.5" NYLON 10
8A004-007-1 BLK OFF PLT, VORT, FORD SLOT MAF 1
4FQ114-030 ENG COOL SYS MOD ASY, '15 MUST 1
5W001-085
7P312-050
7P375-050
7P375-075
7P375-098
SLEEVE, FLEX BRAID 1.5" NOM.
5/16 UNION HOSE MENDER
3/8 HOSE UNION, BRASS
3/4" HOSE BARB UNION, BRASS
TEE, 3/8 INCH, PLASTIC
7R002-024 #24 SAE TYPE F SS HOSE CLAMP
1
1
1
1
7R004-001
7R004-002
7R004-004
7U030-056
7U030-065
7U030-109
7U031-016
7U038-000
STEPLESS CLAMP, 15.7-70
STEPLESS CLAMP, 17.0-70
STEPLESS CLAMP, 25.6 X 7MM
3/8 PCV/VAC RUBBER HOSE
HOSE, 3/4 X 90° RUBBER, SHORT
VAC HOSE, 7/64 ID
5/16 PCV/VAC RUBBER HOSE
3/4 HEATER HOSE
8N155-090 WATER TANK WELD ASY, 2015 MUST
4
7
1
1
2
2.5
1
.50FT
1
3
1
4FQ112-074 DISCH ASY, 2015 MSTG 5.0 BLK 1
4FQ012-074 DISCH TUBE A, 2015 MUSTANG GT
4FQ012-094 DISCH TUBE C, 2015 MUSTANG GT
4FQ017-051 SPACER, TB, 1.25, 2011 MSTG 5.0
4FQ112-084 ASSY, DISCH TUBE B, '15 MUST GT
4FQ112-104 DISCH DUCT ASY 'D', '15 MUST GT
1
1
7C060-080
7F008-021
7J006-093
7J312-875
M6 X 1.00 X 80 SHCS CL 12.9
NUT, M8 X 1.25, SERRATED FLG
6MM WASHER, PLATED
5/16" WASHER, 7/8" OD, CUSTOM
7P062-187
7P157-219
1/16 NPT X 3/16 HOSE BARB
REDUCER UNION, 5/32" TO 7/32"
7P500-016 TEE, .5 X .5 X 1/16 NPT, METAL
7PS300-277 SLEEVE, BUMP REDUCER, 3.0-2.75
7PS300-300
7PS300-301
7PS350-301
SLEEVE, BLACK, 3.00D X 3.00
BUMP HOSE, 3.00D X 3.00L
7PS350-200 SLEEVE, BLACK 3.50 ID X 2.0" LG
REDUCER, BLK 3.5-3.0 X 3.0L
7PS400-351 REDUCER SLEEVE, 4.0 X 3.5 X 2.3
7PS400-354 ELBOW, 4.0 X 3.5 S-SHAPE, SILI
7R002-044 #44 SAE TYPE F SS HOSE CLAMP
4
1
4
4
1
4
1
1
7R002-048 #48 SAE TYPE F SS HOSE CLAMP
7R002-052 #52 SAE TYPE F SS HOSE CLAMP
7R002-056 #56 SAE TYPE F SS HOSE CLAMP
7R002-064 #64 SAE TYPE F SS HOSE CLAMP
7U012-238
7U030-046
7U030-218
8A103-094
8H040-175
O-RING, 2-238, 4.384ID X .139
5/32" VACUUM LINE
7/32 VAC HOSE, BUNA-N
MAF ASSY, 2015 MUST GT, BLK
FILTER, 1.75" I.D., RACE BYPASS
1
2
1
.25
7
4
1
1
5
1
1
1
1
1
1
1
2
1
1
8D204-064 MAXFLOW BYPASS VALVE, G3 BLK 1
8PN101-054 WELDED CORE ASY,05 MUST, BLK 1
8F160-046 FUEL INjECTOR ASSY, 2011 MSTG 1
4FQ017-041 SPCR, FUEL RAIL, EV14, 2011 MSTG GT 4
8F060-046 FUEL INJ, 47LB EV14
7C060-091 M6 X 1.0 X 90MM SHCS PLT GR12.9
7J250-001 1/4 WASHER, SAE, PLATED
8
4
4
8H040-205 AIR FILTER, 2015 MSTG GT PANEL 1
5A003-070 SCT TUNER, 11-15 MUSTANG GT 1
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured vi
1. BASIC COMPONENT REMOVAL
the original location of each for future re-use.
A. Remove eight (8) plastic fasteners securing the black plastic cover above the grille and radiator.
Pop the center section of each fastener upward and then the larger part of the fastener will loosen.
Remove the cover and set aside for later re-installation. (See Fig. 1-a)
B. Remove the (6) 8mm-headed fasteners securing the front bumper cover to the upper radiator support. Set aside for later re-installation. (See Fig.
1-b)
C. There are (2) 5.5mm-headed fasteners (one on each side) hidden underneath the weather stripping on the top of the bumper cover near the headlights. Remove these fasteners & set aside for later re-installation. (See Fig. 1-c)
D. Remove the 4 plastic fasteners securing the fender liners to the fenders & front undertray. Do this for both sides. (See Fig. 1-d)
Fig. 1-a: Remove Plastic Cover
Fig. 1-b: Remove Bumper Cover Fasteners
Fig. 1-d: Remove Fender Liner Fasteners
1
Fig. 1-c: Remove 5.5mm-Headed Fastener
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
1. BASIC COMPONENT REMOVAL, cont’d
E. Remove the (19) 7mm-headed fasteners & (2) plastic fasteners securing the front undertray to the bumper cover & K-member. (See Fig. 1-e)
F. There are (2) 7mm-headed fasteners (one per side) securing the corners of the front bumper cover to the fender. You will need to pull back the fender liner to access this fasteners & remove.
(See Fig. 1-f)
G. With the front undertray removed, reach up behind the front bumper cover & unplug the fog light connectors. Do this for both sides.
(See Fig. 1-g)
H. Pull the corners of the front bumper cover away from the fender. Carefully remove the front bumper cover from the vehicle, exposing the bumper support. (See Fig. 1-h)
Fig. 1-e: Remove Front Undertray
7MM-HEADED FASTENER
Fig. 1-f: Bumper Corner Fastener
(Bumper Removed)
Fig. 1-h: Front Bumper Cover Removed
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
2
FOG LIGHT CONNECTORS
Fig. 1-g: Fog Light Connectors
1. BASIC COMPONENT REMOVAL, cont’d
I. You will notice a wire harness running along the back side of the bumper support secured by (3) gray clips. Free the harness from the bumper support. (See Fig. 1-i)
J. Release the gray clips from the wire harness & set aside. these will not be reused. (See Fig. 1-j)
K. Unplug the clip from the ambient air temp sensor, then release the harness from the bumper support. Also, remove the sensor & set aside for later re-installation.
Fig. 1-i: Wire Harness
L. Remove the both radiator shrouds. These will be trimmed in a later step. NOTE: If your vehicle is
equipped with the optional front braces, they will
need to be removed. (See Fig. 1-l)
Fig. 1-j: Gray Clip Removal
RADIATOR SHROUDS
Fig. 1-l: Radiator Shrouds
3
AMBIENT AIR TEMP SENSOR
Fig. 1-k: Ambient Air Temp Sensor
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
1. BASIC COMPONENT REMOVAL, cont’d
M. Remove the engine cover, disconnect the hoses going to the intake tube & proceed to remove the intake tube from the vehicle It will not be reused.
(See Fig. 1-m)
N. Remove the interior sound tube by pulling it towards the front of the vehicle. (See Fig. 1-n)
O. Remove the pressure cap from the engine coolant reservoir near the passenger side front of the engine compartment. Locate the engine coolant drain valve at the bottom passenger side corner of the radiator. Open the valve and drain the coolant into a clean container for later reuse. Drain enough to empty the reservoir and below the level of the upper radiator hose. (See Fig. 1-o)
Fig. 1-m: Remove Intake Tube
P. Unclamp and disconnect the two small hoses from the upper portion of the coolant reservoir & disconnect the larger hose from the bottom of the coolant reservoir. Be prepared to catch any spillage. Remove the two (2) 10mm-headed fasteners securing the coolant reservoir. Remove the reservoir and set it aside. It will not be reused
(See Fig. 1-p)
REMOVE TUBE FROM HERE
Fig. 1-n: Remove Interior Sound Tube
RADIATOR DRAIN VALVE
Fig. 1-p: Coolant Reservoir
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
4
Fig. 1-o: Radiator Drain Valve
1. BASIC COMPONENT REMOVAL, cont’d
Q. Release the upper radiator hose clamp connection to the radiator. Release the quick release upper radiator hose connection to the thermostat housing by pulling the spring clip back and sliding the hose fitting off. Remove the upper radiator hose and set it aside for later modification.
Remove the coolant hose to the right of the "Y" fitting, above the thermostat housing & set it aside.
It will not be reused (See Fig. 1-q)
R. Use a 15mm wrench to rotate the belt tensioner counter-clockwise to release tension from the outer 6-rib accessory drive belt. Remove the belt and set it aside as it will not be reused.
(See Fig. 1-r)
S. Remove the two (2) TORX T-20 fasteners securing the MAF insert into the OEM airbox. Remove the MAF insert and set aside for later use.
(See Fig. 1-s)
T. Unplug the electrical connector from the throttle body by sliding the red clip outward and depressing the tab. Remove the four (4) 10mm-headed screws securing the throttle body to the intake manifold. These fasteners will not be reused.
Remove the throttle body and set it aside for later reinstallation, ensuring that the sealing gasket remains in the intake manifold. (See Fig. 1-t)
Fig. 1-q: Upper Radiator Hose Disconnect
Fig. 1-r: Belt Tensioner
Fig. 1-t: Throttle Body
5
Fig. 1-s: MAF Insert
(shown with OEM airbox removed)
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
2. MISCELLANEOUS PREPARATION
A. Free the large wiring harness from the two (2) mounting locations on the engine front cover forward of the passenger side cylinder head. Use extra care when disengaging the lower clip from the threaded hole in the engine cover as this threaded hole will be used in a later step. If part of the clip breaks off in the threaded hole, carefully extract it without damaging the threads. Route the harness higher up along the passenger side valve cover. (See Fig. 2-a)
B. Cut off the coolant reservoir mount closest to the drivers side of the vehicle. This is to make room for the new intake tube. You may need to make further adjustments when you install the intake tube. (See Fig. 2-b)
C. Remove the battery cover by removing the (3) plastic fasteners & pulling forward. (See Fig. 2-c)
Fig. 2-a: Wiring Harness
D. Unplug the battery leads. (See Fig. 2-d)
E. Remove the coil covers from the cylinder heads.
Remove the ignition coils and spark plugs. Re-gap the spark plugs to .032", re-install and torque to 9 ft-lbs. Reinstall the coils and coil covers.
Fig. 2-b: Coolant Reservoir Mount (Removed)
Fig. 2-d: Unplug Battery Leads
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
6
Fig. 2-c: Remove Battery Cover
3. SUPERCHARGER ASSEMBLY PREPARATION
AND INSTALLATION
NOTES:
1. Refer to Figure 3.1 near the end of this section for the size and position of all spacers.
2. Use blue Loctite (thread locker) on the threads of each screw prior to final tightening of the assembly.
A. Using a coarse file or similar tool, remove approximately 1/8” from the front edge of the passenger side valve cover tab. See Fig. 3-a. This will ensure proper supercharger-to-valve cover clearance during installation.
B. Remove the following three (3) 10mm-headed screws securing the engine front cover on the passenger side: (See Fig. 3-b) a. The uppermost screw b. The screw just above the A/C compressor c. The screw between the A/C compressor and the crankshaft
Fig. 3-a Modify Tab
Fig. 3-b: Engine Cover Screws
7
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
3. SUPERCHARGER ASSEMBLY PREPARATION
AND INSTALLATION
C. Inspect the supercharger mounting plate/idler pulley assembly and familiarize yourself with its components and configuration. The new belt should be routed so that the ribbed side engages the ribbed idler pulley and the smooth side rides on the other pulleys. Note the multiple mounting locations of the ribbed idler, used to compensate for different supercharger pulley sizes and belt lengths. All four (4) idler mounting bolts should be left slightly loose during installation to facilitate alignment. (See Fig. 3.1 and Fig. 3.2 Belt Routing
Diagram later in this section)
D. Thread the two (2) included M8 x 200mm studs into the lower two engine cover fastener holes, in the locations of the previously-removed fasteners
(one just above the A/C compressor and one between the A/C compressor and the crankshaft).
Use a small amount of blue thread lock on the threads. Leave approximately 6" of stud exposed.
E. Slide a .875” x 2.058” spacer over the stud above the A/C compressor.
See Fig. 3.1 near the end of this section for this and all other mounting bracket spacer and fastener locations.
F. Slide a .875” x 2.146” spacer over the stud between the A/C compressor and the crankshaft.
G. With the thinner steel plate closer to the engine, begin to slide the mounting bracket assembly over the studs. Place a .875” x 2.730” (.323 I.D.) spacer over each stud, sandwiched between the two mounting plates.
Fig. 3-c: Belt Routing
(front plate removed for clarity)
H. Place a 5/16” flat washer over the open end of each stud and secure with an 8mm flange head nut. Adjust stud exposed length as needed so 1-2 threads protrude beyond the nut. Do not tighten at this time.
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
8
3. SUPERCHARGER ASSEMBLY PREPARATION
AND INSTALLATION, cont'd
I. Locate the .875” x 1.928” spacer and M8 x 80mm hex head screw. Place a 5/16” flat washer on the screw and pass it through the outer (3/8" thick) plate and .875” x 1.928” spacer into the threaded boss on the engine cover in the location furthest toward the passenger side. Do not tighten at this time.
J. Locate the remaining .875” x 2.058” spacer and
M8 x 100mm button head screw. Pass the screw through the inner (1/4" thick) plate (with no washer) and .875” x 2.058” spacer into the uppermost engine cover hole from which an OEM screw was previously removed (2nd hole from the top overall). Do not tighten at this time.
k. Tighten the four (4) idler pulley mounting bolts.
Ensure that the second-highest bolt has the thin washer (the others have standard-thickness washers).
l. Confirm that the four (4) screws and two (2) studs securing the supercharger assembly to the engine are properly aligned. Tighten them in progressive steps in an alternating sequence.
M. Engine Oil Fed Units Only: Locate the included length of black braided 1/2" oil drain hose.
Remove the shipping cap from the 1/2" barbed oil drain fitting on the bottom of the supercharger and attach the drain hose with the included #8 worm gear clamp.
N. Place the supercharger into the cradle of the outer mounting plate, aligning the five (5) mounting holes, with the pulley toward the engine and the discharge pointing straight down. Secure the supercharger to the plate with five (5) 3/8-16 x
1.25 hex head screws with washers. Route the braided drain hose (if equipped) directly downward, away from moving parts and sharp edges, and secure.
9
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
3. SUPERCHARGER ASSEMBLY PREPARATION
AND INSTALLATION, cont'd
O. Align the 6-rib drive belt according to the diagram shown at the end of this section. The belt routing is almost identical to the OEM routing with the exception of the portion that passes between the water pump pulley and crankshaft pulley to drive the supercharger. Ensure that the belt routes smoothly over the supercharger pulley and all of the new idler pulleys as well as the OEM engine accessories.
EVAP
HOSE
P. Use a 15mm wrench to rotate the OEM belt tensioner counter-clockwise and install the belt.
Depending on pulley size, it may be necessary to adjust the location of the ribbed supercharger idler pulley to achieve proper belt tension. Ensure that the belt wraps smoothly around each of the pulleys and that all ribbed pulleys are properly engaging the belt's ribs.
Q. Locate the supplied 1.25” black anodized aluminum throttle body spacer. Install the included large O-ring into the groove in the spacer -- this
O-ring seals against the throttle body, and the smooth side of the spacer seals against the OEM
O-ring in the intake manifold. Reinstall the throttle body,
rotated 180° from its original orientation
(upside-down), using this spacer, the four (4) included M6 x 80mm socket head cap screws, and four (4) included 6mm washers. Ensure that both O-ring seals stay in place. The OEM evaporative emissions tube connecting to the solenoid on the intake manifold just behind the throttle body will have to be slightly bent. (See Fig. 3-d)
R. Carefully snip the strip of tape securing the throttle body electrical harness to the connector housing. Reconnect the connector to the throttle body.
S. Route the large wiring harness near the passenger side valve cover, throttle body electrical harness, and any other items away from moving parts and sharp edges and secure.
Fig. 3-d: Throttle Body Spacer
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
10
FIG. 3.1: MOUNTING BRACKET ASSEMBLY DIAGRAM
11
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
FIG. 3.2: BELT ROUTING DIAGRAM
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
12
4. PCV SYSTEM MODIFICATION
A. Modify and reinstall the passenger side PCV hose as follows: a. Use a razor blade to carefully slit each end of the plastic tube until it can be split away from the barbed fittings inside. Take care not to damage the fittings. (See Fig. 4-a) b. Locate the supplied 90° PCV hose assembly.
(See Fig. 4-b) c. Slide a #25.6 stepless clamp over each open end of the 90° PCV hose assembly and insert one of the previously-removed OEM 90° quick-release fittings into each open end. Do not secure the clamps at this time.
d. Orient the hoses and fittings as shown, test fit to the engine to confirm end fitting clocking for best fit, and secure the clamps. (See Fig. 4-c) e. Install the assembly as shown with the end closest to the 90° plastic elbow connecting to the intake manifold. Secure as needed for clearance to the supercharger pulley. (See
Fig. 4-d)
Fig. 4-a: OEM Passenger Side PCV Hose with fittings removed
Fig. 4-b
Fig. 4-d: Modified Passenger Side PCV Hose,
Installed
Fig. 4-c: Modified Passenger Side PCV Hose
13
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
5. CHARGE AIR COOLER (CAC) & DISCHARGE TUBE
INSTALLATION
NOTE: If your vehicle came equipped with the optional Ford Performance Pack, be sure to sandwich the cooler bracket between the lower brace mounts & bumper support. See Fig. 5-c.
A. Prior to installing the cooler, the radiator shrouds will need to be modified. (See Fig. 5-a)
B. Back out the 4 inner-most screws of the bumper support, leaving about 1/2" of the screw protruding from the back side.
Vehicles equipped with the Ford Performance Pack will need to remove the 4 nuts securing the brace to the back side of the bumper support prior to back-
ing out the screws. Raise the cooler into position, making sure to align the cooler brackets to the 4 screws previously backed out. Once aligned, begin to thread the screws through the cooler brackets. Route the wire harness along the top side of the bumper support. Attach the ambient air temp sensor back to its factory location & plug in the electrical connector.(See Fig. 5-b)
P. SIDE
Fig. 5-a: Modified Radiator Shrouds
D. SIDE
OPTIONAL FRONT BRACES
WIRE HARNESS
INNER BUMPER
SUPPORT SCREWS
C. If your vehicle is not equipped with the optional front braces, proceed to install the cooler against then bumper support, then secure with the provided M8 x 1.25 flanged nut & 5/16 washers.
D. Vehicles equipped with the optional front braces, reuse the factory hardware, making sure the cooler bracket is sandwiched between the lower brace mounts & bumper support. (See Fig. 5-d)
AMBIENT AIR
TEMP SENSOR
COOLER
Fig. 5-b: CAC Installation
OPTIONAL
FRONT BRACE
OEM FLANGED
NUT
CAC
BRACKET
Fig. 5-d: CAC Installation - Vehicles w/ Front
Braces
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
14
5. CHARGE AIR COOLER (CAC) & DISCHARGE TUBE
INSTALLATION, cont'd
E. Remove the 10mm-headed fastener securing the air box, then remove the air box from the vehicle.
(See Fig. 5-e)
F. Remove the snorkel from the air box & set aside.
It will not be reused.
10MM-HEADED
FASTENER
G. Trimming of the air box lid may be required to clear the discharge tube. Trim as necessary.
(See Fig. 5-g)
RUBBER GROMMET
(ATTACHED TO BOX)
Fig. 5-e: Remove Air Box
TRIMMED
SECTION
Fig. 5-g: Trimmed Air Box Lid
15
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
5. CHARGE AIR COOLER (CAC) & DISCHARGE TUBE
INSTALLATION, cont'd
NOTE: Leave all hose clamps loose until all silicone couplers & discharge tubes are free & clear of any obstructions. Hose clamps will be tightened in Step O.
H. Install a straight 3" silicone sleeve & two #48 hose clamps to the passenger side of the cooler. Install a 3" silicone bump sleeve & two #48 hose clamps to the end of Tube B with the smaller bend. Slide the open end of Tube B into the silicone coupler on the cooler. For proper clearance between the body of the vehicle & the windshield washer reservoir, you will need to bend the steel tab, closest to the bypass valve flange, towards the front of the vehicle. (See Fig. 5-h)
BYPASS VALVE
FLANGE
BEND THIS TAB
FORWARD
TUBE B
Fig. 5-h: Tube B Installation
I. Install the 3.00"-2.75" silicone bump reducer sleeve to the volute. The volute end of the sleeve uses a #44 hose clamp, while the tube end uses a
#48 hose clamp. Install Tube A & clock it accordingly. (See Fig. 5-i)
J. Make sure Tube A is clocked in a manner to clear the windshield washer reservoir. (See Fig. 5-j)
3.00" - 2.75"
BUMP
REDUCER
TUBE A
Fig. 5-i: Tube A Installation
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
16
TUBE A
WINDSHIELD
WASHER RESERVOIR
Fig. 5-j: Windshield Reservoir Clearance
5. CHARGE AIR COOLER (CAC) & DISCHARGE TUBE
INSTALLATION, cont'd
K. With tubes A & B in place, attach the bypass valve with the supplied hardware & gasket to the bypass valve flange on Tube B. Make sure that the opening of the bypass valve is facing towards the back of the vehicle. Once secured, attach the supplied 1" filter to the bypass valve & tighten the supplied hose clamp. (See Fig. 5-k)
L. Install the 3.50"-3.0" reducer sleeve to the driver side of the cooler. Secure the cooler end of the reducer sleeve with a #48 hose clamp. Locate
Tube C, which has two 90° bends, and slide one end of the tube into the silicone sleeve on the cooler & secure with a #52 hose clamp. Install a
3.5" silicone sleeve & two #52 hose clamps onto the open end of the Tube C. (See Fig. 5-l)
BYPASS VALVE
FILTER
TUBE B
VACUUM SOURCE
FITTING
Fig. 5-k: Bypass Valve Mounting
M. Make sure that Tube C is clear of the horn. You may need to relocate the horn wiring harness to keep it from resting against Tube C.
(See Fig. 5-m)
HORN
ASSEMBLY
TUBE C
3.50"-3.00"
REDUCER SLEEVE
Fig. 5-l: Tube C Installation
17
HORN
ASSEMBLY
TUBE C
Fig. 5-m: Horn Clearance
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
5. CHARGE AIR COOLER (CAC) & DISCHARGE TUBE
INSTALLATION, cont'd
N. Locate Tube D & insert the one end of the tube into the silicone sleeve previously attached on
Tube C. Attach the supplied 4.00"-3.50" silicone reducer sleeve to the other end of Tube D, then install the MAF housing. Be sure to have the
"FLOW" arrow on the MAF flange facing towards the throttle body. (See Fig. 5-n)
DIRECTION OF FLOW
TUBE D
O. Attach the throttle body sleeve to the throttle body, then attach the other end of the sleeve to the
MAF housing & secure with the provided hose clamps. Once in place, insert the MAF sensor into the flange & secure with the provided hardware.
Connect the MAF plug to the sensor. Verify that all tubes are free of any obstructions then proceed to tighten all of the hose clamps. (See Fig. 5-o)
P. Due to vehicle variances, slight trimming of the hood liner may be required for proper clearance between the hood & the supercharger volute. Trim area as necessary. (See Fig. 5-p)
THROTTLE BODY
SLEEVE
Q. 8-Rib / V-7 Only: The supercharger bracket included in 8-Rib systems positions the supercharger approximately 1/4" further forward than a
6-rib drive system. This may cause interference with the bottom of the OEM hood liner and in some cases the OEM hood. In addition, using a
V-7 supercharger with an 8-rib system may require further clearance due to the larger size of the volute. Vortech suggests placing a few strips of modeling clay on the top of the supercharger volute, then carefully lower the hood, making sure it does not latch shut. Lift the hood & make note of the underhood area that may need to be modified, then clearance as necessary. (See Fig. 5-q)
MAF HOUSING
Fig. 5-n: Tube D & MAF Housing Installation
MAF
CONNECTOR
MAF HOUSING
Fig. 5-o: Throttle Body Sleeve Installation
TRIM HERE
Fig. 5-p: Hood Liner
Fig. 5-q: Modeling Clay
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
18
6. FUEL INjECTOR REPLACEMENT
A. Disconnect the fuel feed line from the fitting near the driver side fuel rail. CAUTION: The fuel line may be pressurized. Take care to avoid spray and spills.
B. Remove the four (4) 10mm hex nuts securing the plastic heater hose guides and set the guides aside for later reinstallation. (See Fig. 6-b)
C. Reposition the vacuum tube assembly mounted under the driver side heater hose guide to facilitate fuel rail removal.
Fig. 6-b: Hose Guide Removal
D. Remove the foam insulation from each fuel rail (2 pieces total).
E. Unplug each of the eight (8) fuel injector electrical connectors.
F. Remove the four (4) 10mm-headed screws securing the fuel rails to the intake manifold (2 per side)
G. Lift the fuel rails (with injectors attached) up and away from the engine, taking care not to spill fuel from the feed fitting. Drain the fuel from the rails.
H. Locate the four (4) OEM aluminum fuel rail spacers lightly pressed into the intake manifold and pull them free. (See Fig. 6-h)
I. Locate the supplied shorter fuel rail spacers and insert them into the intake manifold in place of the
OEM spacers.
Fig. 6-h: Aluminum Fuel Rail Spacers
J. Note the orientation of the OEM injectors in the fuel rails. Disengage the retaining clips and remove the OEM injectors.
K. Install the supplied high-flow injectors into the fuel rails in the same orientation as the OEM injectors and secure in the original fashion with the OEM retaining clips. (See Fig. 6-k)
Fig. 6-k: Fuel Rail / Injector Assembly Detail
19
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
6. FUEL INjECTOR REPLACEMENT, cont'd
L. Install the rail/injector assembly into the intake manifold.
M. Secure the fuel rails with the four (4) included
M10 x 90mm socket head cap screws with washers. (See Fig. 6-m)
N. Connect the fuel injector electrical connectors to each of the eight (8) injectors.
O. Place the foam insulation back over each fuel rail.
P. Place the vacuum tube assembly back into position on the studs near the driver side fuel rail.
Q. Reinstall the plastic heater hose guides and secure with the OEM 10mm hex nuts. Route the heater hoses over them in the OEM fashion.
R. Reconnect the fuel feed line to the fitting on the fuel rail assembly. Make sure it is securely connected in the OEM fashion.
Fig. 6-m: Re-securing Fuel Rails
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
20
7. ENGINE COOLING SYSTEM MODIFICATION
A. Locate the previously-removed OEM upper radiator hose. Remove the factory spring clamp & set aside. Cut off 3" from the end of the hose.
(See Fig. 7-a)
B. Cut away the OEM plastic hose clamp on the quick-release end of the radiator hose, taking care not to damage the hose. Separate the hose from the quick-release fitting. (See Fig. 7-b)
C. The upper radiator hose will need to be flipped when re-installed on the vehicle in order to provide adequate space between the upper radiator hose & the supercharger. The end of the hose originally attached to the quick-release fitting will now be attached to the upper radiator inlet. The other end will now be attached to the quickrelease fitting. (See Fig. 7-c)
D. Once both ends of the hose are attached & properly clocked, secure the radiator-side of the hose using the previously removed spring clamp. Use the supplied #24 hose clamp on the quick-release side of the hose. (See Fig. 7-d)
CUT OFF 3" FROM THIS END
Fig. 7-a: Upper Radiator Hose
(OEM Configuration)
PLASTIC HOSE CLAMP
Fig. 7-b: Cut Plastic Hose Clamp
SUPPLIED #24 HOSE CLAMP
Fig. 7-d: #24 Hose Clamp
21
Fig. 7-c: Upper Radiator Hose
(New Configuration)
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
7. ENGINE COOLING SYSTEM MODIFICATION, cont'd
E. To the right of the passenger side shock tower you will see a ground strap for the electric power steering system. You will need to relocate this strap to the harness mount directly below the original mounting location for this ground strap. Reuse
OEM hardware. (See Fig. 7-e)
ELECTRIC P/S
GROUND STRAP
F. Remove the (1) 13mm-headed screw on the brace to the right of the battery & attach the new coolant reservoir as shown. (See Fig. 7-f)
RELOCATE GROUND
STRAP TO THIS
HARNESS MOUNT
G. The second mount of the coolant reservoir will be mounted where the eletric power steering ground strap was previously attached. Reuse the 8mmheaded fastener to fasten the coolant reservoir.
(See Fig. 7-g)
Fig. 7-e: Ground Strap Relocation
H. Locate the included 3/8” hose and cut a 2” piece.
Install the piece onto the hose barb on the replacement coolant reservoir and secure with an included #17 stepless clamp. (See Fig. 7-h)
Fig. 7-f: Coolant Reservoir Mount #1
Fig. 7-h: Ø3/8" x 2" Hose
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
22
RELOCATED
ELECTRIC P/S
GROUND STRAP
Fig. 7-g: Coolant Reservoir Mount #2
7. ENGINE COOLING SYSTEM MODIFICATION, cont'd
I. Slide another #17 stepless clamp onto the 2” piece and then insert the black plastic TEE as shown, so one leg points forward and one points to the driver side. Secure with the #17 stepless clamp. (See Fig. 7-i)
J. Locate the small coolant hose running from the driver side front of the engine previously disconnected from the OEM coolant reservoir. Cut the hose in the approximate location shown.
(See Fig. 7-j)
K. Install the cut-off portion of the small coolant hose onto the driver side-facing port of the previouslyinstalled TEE and orient as shown. Secure with the OEM clamp. (See Fig. 7-k)
Fig. 7-i: Ø3/8" x 2" Hose
Fig. 7-j: Small Coolant Hose
23
Fig. 7-k: Small Coolant Hose
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
7. ENGINE COOLING SYSTEM MODIFICATION, cont'd
L. Use the included 5/16” hose, 5/16” barbed hose unions, and #15.7 stepless clamps to extend the upper coolant hose along the top of the engine to the previously cut-off portion connected to the
TEE. Route the hose under the large wiring harness as shown and secure away from moving parts and sharp edges. Trim to length and secure with the #15.7 stepless clamps. (See Fig. 7-l)
M. Locate the coolant overflow hose running along the top of the radiator (previously disconnected from the OEM coolant reservoir). Pull back the abrasion sleeve and cut the hose about 1" into the straight section at the driver side end. Use the included 3/8” hose, 3/8” barbed hose union, and
#17 stepless clamps to extend the coolant overflow hose along the top of the radiator, under the passenger side upper radiator mount (along the wiring harness) and around to the area of the replacement coolant reservoir. (See Fig. 7-m)
Fig. 7-l: 5/16" Coolant Hose, Extended
N. Install the cut-off portion from the previous step onto the forward-facing leg of the TEE installed above and orient as shown. Secure with the OEM clamp. (See Fig. 7-n)
O. Use the included 3/8” hose, 3/8” barbed hose union, and #17 stepless clamps to connect the lengthened coolant overflow hose to the previously cut-off portion connected to the TEE. Trim to length and cover with the OEM abrasion sleeve.
(See Fig. 7-o)
Fig. 7-m: Coolant Overflow Hose Cut & Splice
Fig. 7-o: Small Coolant Hoses
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
24
Fig. 7-n: Coolant Overflow Hose
7. ENGINE COOLING SYSTEM MODIFICATION, cont'd
P. Locate the provided 3/4" 90° hose elbow, 3/4" brass hose union & (2) 25.6 stepless clamps.
Slide the hose union into one end of the hose elbow & the other end into the length of provided
3/4" hose. Use the 25.6 stepless clamps to secure. Attach the other end of the hose elbow to the drivers side heater tube & secure with the
OEM hose clamp. (See Fig. 7-p)
Q. Route the open end of the new ¾” coolant hose
(with OEM abrasion sleeve attached) across the front of the motor & attach to the new coolant reservoir on the passenger side. (See Fig. 7-q)
R. Attach the provided length of 7/64 rubber hose to the brass fitting next to the threaded bung & route it towards the bottom of the vehicle. Refill the engine cooling system via the replacement coolant reservoir with the previously-drained coolant.
Filter if needed, ensuring no contaminants enter the cooling system. The coolant reservoir should be approximately 1/2 full. Do not overfill. Close the reservoir with the OEM cap from the OEM coolant reservoir.
Fig. 7-p: 3/4" 90° Hose Elbow
NOTE: Periodically check the coolant level once the car is running and the cooling system purges.
Fig. 7-q: 3/4" Coolant Hose Routing
25
Fig. 7-r: 3/4" Coolant Reservoir
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
8. AIR INLET ASSEMBLY INSTALLATION
A. Remove the protective cover from the OEM dual check valve assembly. The following hoses will need to be removed from the dual check valve assembly:
a. Remove the hard plastic vacuum hose from the dual check valve assembly by slicing it the end with a razor blade. The other end of the hose is connected to a hard plastic tube with another check valve that runs beneath the passenger side of the intake manifold. Slice the hose at the check valve & remove it from the hard plastic tube. (See
Fig. 8-e for reference)
b. Remove breather hose "A" from the dual check valve assembly. It will not be reused.
c. Remove breather hose "B" from the hard plastic tube that runs beneath the drivers side of the intake manifold. (See Fig. 8-c for a view of the
hard plastic tube.)
REMOVE VACUUM
HOSE
REMOVE
PROTECTIVE
COVER
REMOVE
BREATHER
HOSE "B"
FROM HARD
PLASTIC TUBE
REMOVE
BREATHER
HOSE "A"
Fig. 8-a: Dual Check Valve Assembly
B. With the hoses removed, you should be left with the ports on the left side of the dual check valve exposed. (See Fig. 8-b)
C. Cut a piece of 3/8" hose, roughly 2.5" in length, & attach it to the open end of the hard plastic tube that runs beneath the drivers side of the intake manifold. Route the hose under the fuel rail cross over tube. (See Fig. 8-c)
D. Insert the provided 3/8" plastic tee into the open end of the 3/8" hose. Do not attach any other hoses to the tee at this time. (See Fig. 8-d for reference)
BLACK PORT
GRAY PORT
OEM DUAL
CHECK VALVE
Fig. 8-b: Dual Check Valve Assembly
(Hoses Removed)
TO HARD PLASTIC
TUBE (DRIVER SIDE)
HARD PLASTIC TUBE
(DRIVER SIDE)
INTAKE
MANIFOLD
3/8" HOSE
TO OEM DUAL
CHECK VALVE
(GRAY PORT)
TO INLET
TUBE
Fig. 8-d: 3/8" Tee Attached
(Reference)
FUEL RAIL
CROSS OVER
Fig. 8-c: 3/8" Hose - Hard Plastic Tube
(Drivers Side)
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
26
8. AIR INLET ASSEMBLY INSTALLATION, cont'd
E. Attach a length of 3/8" hose to the other hard plastic tube which runs underneath the passenger side of the intake manifold. (See Fig. 8-e)
TO OEM DUAL
CHECK VALVE
(BLACK PORT)
HARD PLASTIC TUBE w/
CHECK VALVE
(PASSENGER SIDE)
F. Attach the open end of the 3/8" hose to the black port on the dual check valve assembly.
(See Fig. 8-f)
G. Cut a 12" section & 2.5" section of 3/8" hose.
Locate the provided 3/8" check valve & assemble it as shown in Fig. 10-g. Note the direction of flow on the check valve. (See Fig. 8-g)
H. Attach the long section of 3/8" hose to the previously installed 3/8" plastic tee, then attach the short section of hose to the gray port on the dual check valve assembly. The arrow on the provided check valve should be pointing toward the gray port of the dual check valve. (See Fig. 8-h)
Fig. 8-e: 3/8" Hose - Hard Plastic Tube
(Passenger Side)
NOTE: Make sure that the hose routing is such that the rubber hose bends are smooth and do not pinch or kink.
Fig. 8-f: 3/8" Hose Attachment
OEM DUAL
CHECK VALVE
12" SECTION
OF HOSE
DIRECTION
OF FLOW
Fig. 8-h: 3/8" Hose w/Provided Check Valve
27
2.5" SECTION
OF HOSE
Fig. 8-g: Hose Arrangement w/Provided Check Valve
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
FIG. 8.1: VACUUM ROUTING DIAGRAM
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
28
8. AIR INLET ASSEMBLY INSTALLATION, cont'd
I. Locate the provided 5/8" plastic tee, 5/8"-3/8" reducer fitting, OEM breather hose & provided
5/8" hose. Assemble the 5/8" tee & 5/8"-3/8" reducer fitting as shown in Fig. 8-j.
TO VALVE
COVER
J. Locate the OEM breather hose & remove the 90° quick release connector from the hose. Insert the quick release connector into a length of 5/8" hose, then attach the other end of the hose to the 5/8" tee. Secure both ends of the hose with 25.6 stepless clamps. Secure the 5/8" hose that goes into the intake tube fitting with the provided hose clamp. Attach a length of 3/8" hose from the 5/8-
3/8 reducer fitting to the 3/8" tee that was previously installed. (See Fig. 8-j)
K. Use the provided MAF port cover to block off the original location of the MAF sensor. Reuse the
OEM hardware to secure the MAF port cover.
(See Fig. 8-k)
TO 3/8"
TEE
5/8"-3/8"
REDUCER
FITTING
TO INTAKE
TUBE FITTING
Fig. 8-j: Driver Side PCV Hose Modification
(Reference)
Fig. 8-k: Air Inlet to Airbox Connection; MAF
Port Cover
29
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
9. BYPASS VALVE CONNECTION
A. Locate the supplied vacuum tee fittings & assemble them as shown. (See Fig. 9-a)
B. Cut the OEM vacuum hose shown & insert the vacuum tee as shown. (See Fig. 9-b)
C. Attach the 7/32-5/32 reducer fitting & short length of 5/32 vacuum hose to the vacuum tee. Locate the supplied 7/32 vacuum hose & attach it to the reducer fitting. Run the vacuum hose along the top of the vehicle, across to the passenger side of the car. Route the vacuum hose down to the discharge tube with the bypass valve, making sure to avoid damaging the hose. Use the supplied zip ties to secure the vacuum hose. (See Fig. 9-c)
D. Attach the open end of the 7/32 vacuum hose to the vacuum port on located on the top of the bypass valve. (See Fig. 9-d)
Fig. 9-a: Vacuum Tee Installation
VACUUM TEE
Fig. 9-b: Vacuum Tee Installation
7/32 HOSE
7/32-5/32
REDUCER
BYPASS VALVE
VACUUM SOURCE
FITTING
Fig. 9-d: Bypass Valve
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
30
5/32 HOSE
Fig. 9-c: Vacuum Hose Routing
10. MISCELLANEOUS REASSEMBLY
A. Trim the passenger side front corner of the engine cover as shown. Start with a small cut and check fitment, only trimming away as much as necessary for clearance. (See Fig. 10-a)
B. Reinstall all previoulsy removed panels & bumper cover. Check for proper fitment & clearance during reinstallation.
C. Plug the battery back in & secure the leads.
Fig. 10-a: Engine Cover Cut Detail
31
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
11. OIL FEED INSTALLATION (OIL-FED UNITS ONLY)
A. Locate the supercharger oil feed port on the passenger side of the supercharger. (See Fig. 11-a)
B. Remove the blue plastic plug from the supercharger oil feed port and install the included -4AN male fitting. (See Fig. 11-b)
Teflon tape or pipe sealant is not recommended as it might loosen and cause blockage of the small oil feed orifice resulting in possible supercharger failure.
C. Connect the 90° end of the included -4AN braided oil feed hose to the supercharger oil feed fitting.
Route the hose downward and toward the driver side between the supercharger discharge and the forward mounting plate. (See Fig. 11-c)
D. Continue routing the oil feed hose to the lower driver side area of the engine, passing it rearward between the alternator and the engine oil filter.
Use extra care to secure the hose away from moving parts and sharp edges.
Fig. 11-a: Supercharger Oil Feed Location
Fig. 11-b: -4AN Oil Feed Fitting Installed
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
32
Fig. 11-c: 90° Oil Feed Hose Installed
11. OIL FEED INSTALLATION (OIL-FED UNITS ONLY), cont'd
E. Locate the OEM oil pressure sensor located just above and behind the engine oil filter.
(See Fig. 11-e)
F. Disconnect the electrical connector from the OEM oil pressure sensor and remove the sensor itself by unthreading it from its 1/4" NPT port.
Temporarily plug the port, as a small amount of oil may drain out.
G. Install the supplied 1/4" NPT TEE fitting into the oil pressure sensor port and orient so one female port faces upward and one faces outward.
Fig. 11-e: OEM Oil Pressure Sensor
NOTE: Use only clean engine oil on the pipe threads.
Teflon tape or pipe sealant is not recommended as it might loosen and cause blockage of supercharger failure.
H. Install the OEM oil pressure sensor into the upward-facing port of the TEE. (See Fig. 11-h)
I. Install the 1/4" NPT male x -4AN male 90° fitting into the outward-facing port of the TEE. Orient to point forward and slightly down. (See Fig. 11-h)
J. Reconnect the electrical connector to the OEM oil pressure sensor.
K. Connect the straight end of the previouslyinstalled -4AN braided hose to the -4AN male 90° fitting installed into the TEE, routing the hose between the alternator and oil filter.
(See Fig. 11-k)
L. Confirm that all oil feed fittings are secure and that the hose is secured in a smooth path free of kinks and away from moving parts and sharp edges.
Fig. 11-h: Oil Feed Assembly
(shown removed for clarity)
33
Fig. 11-k: Oil Feed Assembly Orientation
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
12. OIL DRAIN INSTALLATION (OIL-FED UNITS
ONLY)
NOTE: To provide an oil drain for the supercharger, it is necessary to make a hole in the oil pan. It is best to punch the hole rather than to drill it.
A. Locate the wiring harness secured to the front edge of the oil pan. Remove the two (2) 10mm nuts securing the wiring harness mounting brackets (one on each side of the crankshaft), allowing the harness to be pulled downward for improved access to the front face of the oil pan.
(See Fig. 12-a)
B. Mark the location for the oil drain fitting on the smooth portion of the front face of the oil pan toward the passenger side, approximately 5/8" down from the oil pan mounting flange. (See Fig.
12-b; also see Fig. 12-1 at the end of this section)
C. Remove paint from the area around the hole location.
Fig. 12-a: Wiring Harness Mounting Location
(pass. side shown, driver side similar)
D. Use a small center punch to perforate the pan and expand the hole. Switch to a larger diameter punch and expand the hole further to approximately Ø9/16". Most punches are made from hexagon material and may be placed in a socket with an extension to make this procedure easier.
(See Fig. 12-d)
E. Tap the hole with a 3/8" NPT tap approximately
1/4" deep. Pack the flutes of the tap with heavy grease to hold chips. Use a small magnet to check for any stray chips.
Fig. 12-b: Oil Drain Fitting Installation Location
NOTE: This method of rolling over the lip of the hole and tapping it works very well if carefully done and should cause no problems.
F. Thoroughly clean the threaded area. Apply a small amount of silicone sealer or Teflon paste to the new threads. Apply more sealer to the included 3/8" NPT hose barb fitting and install the fitting into the hole, making sure a seal is formed all around the fitting.
G. Change the engine oil and filter to flush out any contaminants that may have entered the oil pan.
Fig. 12-d: Punching Hole in Oil Pan
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
34
12. OIL DRAIN INSTALLATION (OIL-FED UNITS
ONLY), cont'd
H. Locate the oil drain hose previously attached to the barb fitting on the bottom of the supercharger.
Trim the hose to length and secure to the barbed drain fitting on the front of the oil pan with an included worm gear clamp.
NOTE: Use extra care to secure the drain hose away from moving parts and sharp edges. It is important that the hose travels downhill for its entire length.
I. Resecure the wiring harness running in front of the oil pan, using the included brass spacers to relocate the harness downward for drain hose clearance. (See Fig. 12-i)
Fig. 12-i: Wiring Harness Spacer
Fig. 12-1: Oil Drain Fitting Placement
35
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
13. REFLASH COMPUTER
IMPORTANT! To ensure trouble-free programming of your vehicle's computer:
• Make sure the vehicle's battery is sufficiently charged.
• Turn off all accessories and close doors to prevent unnecessary drain on the battery.
• Do not attempt to program your vehicle while a battery charger is connected.
• Improper battery voltage will result in failure of the programming process.
• Do not disconnect the cable or turn off the ignition during programming unless prompted to do so.
A. Reconnect the battery.
B. Locate the vehicle’s OBD2 port located in the lower left hand corner of the dash on the driver side of the vehicle. (See Fig. 13-b)
C. Attach the OBD2 connector from the provided
Flash tool (See Fig. 13-c) to the vehicle’s
OBD2 port (See Fig 13-b). Make sure this connector is seated all the way into the vehicle’s OBD2 port. Do not allow this connector to become disconnected during programming or damage may occur to the vehicle’s ECM.
D. The Reflash tool will power up and display
"Program Vehicle". Press SELECT.
E. Press SELECT again to choose the default selection on the following screen.
F. Follow the on-screen prompts to step through the reflash process.
• When prompted to turn the key on, do so and wait for the vehicle to fully "boot up" before proceeding.
• When prompted to "Select Vehicle" select
"Mustang GT HO"
•
•
When prompted to "Adjust Options" select "Skip Options"
Select "Begin Program"
G. Turn the key off when prompted.
H. When the tool returns to the "Program
Vehicle" screen the process is complete.
I. Unplug the reflash tool from the OBD2 port and store in a safe place for later use.
NOTE: Do not disturb the cable or turn the ignition off during this programming. If the programming is disrupted, the computer will not start or run your vehicle!
Fig. 13-b: OBD2 Connector and Port
Fig. 13-c: Flash Tool
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
36
14. FINAL CHECK
WARNING: Do not attempt to operate the vehicle until all components are installed and all operations are completed including the final check.
A. If your vehicle has gone over 15,000 miles since its last spark plug change, you will need to change the spark plugs now before test driving the vehicle.
B. Check all fittings, nuts, bolts and clamps for tightness. Pay particular attention to oil and fuel lines around moving parts, sharp edges, and exhaust system parts. Make sure all wires and lines are properly secured with clamps or tie-wraps.
C. Check all fluid levels, making sure that your tank is filled with 91 octane or higher fuel before commencing test drive.
D. Start the engine and allow to idle a few minutes, then shut off.
E. Recheck to be sure that no hoses, wires, etc. are near exhaust headers or moving parts.
Look also for any signs of fluid leakage.
F. PLEASE TAKE SPECIAL NOTE: Operating the vehicle without ALL of the subassemblies completely and properly installed may cause
FAILURE OF MAJOR COMPONENTS.
G. Test drive the vehicle.
H. Always listen carefully for engine detonation.
Discontinue heavy throttle usage if detonation is heard.
I.
Read the
STREET SUPERCHARGER
SYSTEM OWNER'S MANUAL AND
RETURN THE WARRANTY REGISTRATION
FORM within thirty (30) days of purchasing your supercharger system to qualify.
For internally lubricated V3 units only
This supercharger has been factory pre-filled with special Vortech synthetic lubricant. Oil does not need to be added to a brand new unit, however a fluid level check should be performed.
Prior to operating the supercharger on the vehicle and after installation onto the vehicle:
Remove the factory installed flat-head brass shipping plug (not the dipstick) from the top of the supercharger case. Replace the sealed shipping plug with the supplied vented plug. Do not operate the supercharger without it. Check the supercharger fluid level using the dipstick as follows:
Fluid level checking procedure:
1. Ensure that the .06” copper sealing washer
is located on the dipstick base.
2. Thread the clean dipstick into the unit until
it seats.
3. Once the dipstick has seated, remove the
dipstick from the unit. Fluid should register
in the crosshatched area on the dipstick.
4. DO NOT OVERFILL!!! Drain excess fluid from
the unit if it is above the maximum level on
the dipstick.
Check the fluid level using the dipstick at least every
2,500 miles.
Initial supercharger fluid change must be performed at 2,500 miles. The supercharger fluid must be changed every 7,500 miles maximum thereafter.
Drain the fluid, refill the unit with 4 oz. of Vortech V3 lubricating fluid, and then confirm proper oil level using the dipstick. DO NOT OVERFILL!!!
WARNING: Use of any fluid other than the special Vortech lubricant will void the warranty and may cause component failure.
37
P/N: 4FQ020-015 v1.4c, 01/28/2016
©2015 Vortech Engineering, Inc
All Rights Reserved, Intl. Corp. Secured
®
ENGINEERING, INC
1650 Pacific Avenue, Channel Islands CA 93033-9901 • Phone: 805 247-0226
Fax: 805 247-0669 • www.vortechsuperchargers.com
©2015 Vortech Engineering, Inc.
All Rights Reserved, Intl. Corp. Secured
38
advertisement
Key Features
- Supercharger Kit
- 2015-2016 Ford Mustang GT
- Installation Guide
- Detailed Illustrations
- Technical Specifications
- Comprehensive Maintenance & Service Information
Frequently Answers and Questions
What is the octane rating requirement for the fuel?
What modifications are required to the vehicle before installation?
What are the warranty exclusions for this product?
Related manuals
advertisement
Table of contents
- 7 BASIC COMPONENT REMOVAL
- 12 MISCELLANEOUS PREPARATION
- 13 SUPERCHARGER ASSEMBLY PREPARATION & INSTALLATION
- 17 3.1 MOUNTING BRACKET ASSEMBLY DIAGRAM
- 18 3.2 BELT ROUTING DIAGRAM
- 19 PCV SYSTEM MODIFICATION
- 20 CHARGE AIR COOLER (CAC) & DISCHARGE TUBE INSTALLATION
- 25 FUEL INJECTOR REPLACEMENT
- 27 ENGINE COOLING SYSTEM MODIFICATION
- 32 AIR INLET ASSEMBLY INSTALLATION
- 34 8.1 VACUUM ROUTING DIAGRAM
- 37 10. MISCELLANEOUS REASSEMBLY
- 38 11. OIL FEED INSTALLATION (OIL-FED UNITS ONLY)
- 40 12. OIL DRAIN INSTALLATION (OIL-FED UNITS ONLY)
- 42 13. REFLASH COMPUTER
- 43 14. FINAL CHECK