ICOM MA-500TR Owner Manual

ICOM MA-500TR Owner Manual

ICOM MA-500TR is a Class B AIS transponder that provides real-time vessel traffic information on its full dot-matrix display. With its IPX7 waterproof protection and 3 lines of NMEA0183 Input/Output, it's built to withstand harsh marine environments and seamlessly integrate with your existing marine electronics. The included GPS receiver and collision-risk management functions enhance your situational awareness and safety on the water. Plus, its integration with Icom VHF transceivers makes it a versatile and convenient addition to your marine communication system.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

ICOM MA-500TR Owner Manual | Manualzz
INSTRUCTION MANUAL
CLASS B AIS TRANSPONDER
MA-500TR
This device complies with Part 15 of the FCC
Rules. Operation is subject to the condition that
this device does not cause harmful interference.
FOREWORD
IMPORTANT
Thank you for purchasing this Icom product.
The MA-500TR class b ais transponder is designed and
built with Icom’s state of the art technology and craftsmanship. With proper care, this product should provide you with
years of trouble-free operation.
READ ALL INSTRUCTIONS carefully and completely
We appreciate you making the MA-500TR your transponder of choice, and hope you agree with Icom’s philosophy of
“technology first.” Many hours of research and development
went into the design of your MA-500TR.
D FEATURES
❍ Full dot-matrix display visually shows real-time
vessel traffic information
❍ IPX7 waterproof protection
❍3 lines of NMEA0183 Input/Output
❍ GPS receiver comes with the MA-500TR
❍ Collision-risk management functions
❍ Integration with Icom VHF transceivers*
i
* See the leaflet that comes with the transponder for details of the
corresponding transceiver.
before using the transponder.
SAVE THIS INSTRUCTION MANUAL — This instruction manual contains important operating instructions
for the MA-500TR.
EXPLICIT DEFINITIONS
WORD
DEFINITION
RWARNING!
Personal injury, fire hazard or electric
shock may occur.
CAUTION
NOTE
Equipment damage may occur.
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
CLEAN THE TRANSPONDER THOROUGHLY WITH
FRESH WATER after exposure to saltwater, otherwise, the
keys and switch may become inoperable due to salt crystallization.
FCC INFORMATION
• FOR CLASS B UNINTENTIONAL RADIATORS
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
SUPPLIED ACCESSORIES
DC power cable (OPC-2059)
NMEA connector cable
(OPC-2014)
• The OPC-2014 has 15
leads, numbered 1 to 15.
Mounting bracket
For the mounting bracket
Knob bolts
Flat washers
(M5)
Screws (5×20) Spring washers
(M5)
MXG-5000 gps receiver is included with MA-500TR.
MXG-5000 (Referred to as Internal GPS)
Cable length: Approx. 10 m (32.8 ft)
• An instruction sheet comes with the MXG5000. Please read it before installing and
operating the MXG-5000.
ii
RADIO OPERATOR WARNING
Icom requires the radio operator to meet the
FCC Requirements for Radio Frequency Exposure. An omnidirectional antenna with gain not
greater than 9 dBi must be mounted a minimum
W ARN ING of 5 meters (measured from the lowest point of
the antenna) vertically above the main deck and
all possible personnel. This is the minimum safe separation
distance estimated to meet all RF exposure compliance requirements. This 5 meter distance is based on the FCC Safe
Maximum Permissible Exposure (MPE) distance of 3 meters
added to the height of an adult (2 meters) and is appropriate
for all vessels.
For watercraft without suitable structures, the antenna must
be mounted so as to maintain a minimum of 1 meter vertically
between the antenna, (measured from the lowest point of the
antenna), to the heads of all persons AND all persons must
stay outside of the 3 meter MPE radius.
Do not transmit with radio and antenna when persons are
within the MPE radius of the antenna, unless such persons
(such as driver or radio operator) are shielded from antenna
field by a grounded metallic barrier. The MPE Radius is the
minimum distance from the antenna axis that person should
maintain in order to avoid RF exposure higher than the allowable MPE level set by FCC.
iii
FAILURE TO OBSERVE THESE LIMITS MAY ALLOW
THOSE WITHIN THE MPE RADIUS TO EXPERIENCE RF
RADIATION ABSORPTION WHICH EXCEEDS THE FCC
MAXIMUM PERMISSIBLE EXPOSURE (MPE) LIMIT.
IT IS THE RESPONSIBILITY OF THE RADIO OPERATOR
TO ENSURE THAT THE MAXIMUM PERMISSIBLE EXPOSURE LIMITS ARE OBSERVED AT ALL TIMES DURING
RADIO TRANSMISSION. THE RADIO OPERATOR IS TO
ENSURE THAT NO BYSTANDERS COME WITHIN THE
RADIUS OF THE MAXIMUM PERMISSIBLE EXPOSURE
LIMITS.
Determining MPE Radius
THE MAXIMUM PERMISSIBLE EXPOSURE (MPE) RADIUS
HAS BEEN ESTIMATED TO BE A RADIUS OF ABOUT 3M
PER OET BULLETIN 65 OF THE FCC.
THIS ESTIMATE IS MADE ASSUMING THE MAXIMUM
POWER OF THE RADIO AND ANTENNAS WITH A MAXIMUM GAIN OF 9dBi ARE USED FOR A VESSEL MOUNTED
SYSTEM.
ABOUT CE
• INSTALLATION NOTES
The installation of this equipment should be made in such a
manner as to respect the EC recommended electromagnetic
field exposure limits (1999/519/EC).
The maximum RF power available from this device is 2 watts.
The antenna should be installed as high as possible for maximum efficiency and that this installation height should be
at least 5 meters above ground (or accessible) level. In the
case where an antenna cannot be installed at a reasonable
height, then the transmitter should neither be continuously
operated for long periods if any person is within 5 meters of
the antenna, nor operated at all if any person is touching the
antenna.
In all cases any possible risk depends on the transmitter
being activated for long periods. (actual recommendation limits are specified as an average of 6 minutes) Normally the
transmitter is not active for long periods of time. Some radio
licenses will require that a timer circuit automatically cuts the
transmitter after 1 to 2 minutes etc.
Similarly some types of transmitter, SSB, CW, AM, etc. have
a lower ‘average’ output power and the perceived risk is even
lower.
CE versions of the MA-500TR which display
the “CE” symbol on the serial number label,
comply with the essential requirements of the
European Radio and Telecommunication Terminal Directive 1999/5/EC.
This warning symbol indicates that this equipment operates in non-harmonised frequency
bands and/or may be subject to licensing conditions in the country of use. Be sure to check
that you have the correct version of this radio
or the correct programming of this radio, to
comply with national licensing requirement.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
iv
ABOUT CE
DECLARATION
OF CONFORMITY
We Icom Inc. Japan
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan
Declare on our sole responsibility that this equipment complies with the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.
Kind of equipment:
CLASS B AIS TRANSPONDER
Type-designation:
ma- 500tr
0560
Bad Soden
2nd Dec. 2010
Place and date of issue
Icom (Europe) GmbH
Communication Equipment
Auf der Krautweide 24,
65812 Bad Soden am Taunus,
Germany
Authorized representative name
Version (where applicable):
This compliance is based on conformity with the following harmonised
standards, specifications or documents:
i) IEC 62287-1 Ed.1
ii) ITU-R M.1371-3
iii) ITU-R M.825-3
iv) IEC 60945 2002
v) EN 60950-1 2006 A11:2009
vi)
vii)
viii)
v
Y. Furukawa
General Manager
Signature
• List of Country codes (ISO 3166-1)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Country
Austria
Belgium
Bulgaria
Croatia
Czech Republic
Cyprus
Denmark
Estonia
Finland
France
Germany
Greece
Hungary
Iceland
Ireland
Italy
Latvia
Codes
AT
BE
BG
HR
CZ
CY
DK
EE
FI
FR
DE
GR
HU
IS
IE
IT
LV
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Country
Codes
Liechtenstein
Lithuania
Luxembourg
Malta
Netherlands
Norway
Poland
Portugal
Romania
Slovakia
Slovenia
Spain
Sweden
Switzerland
Turkey
United Kingdom
LI
LT
LU
MT
NL
NO
PL
PT
RO
SK
SI
ES
SE
CH
TR
GB
PRECAUTIONS
RWARNING! NEVER connect the transponder to an
AC outlet. This may pose a fire hazard or result in an electric
shock.
RWARNING! NEVER connect the transponder to a
power source of more than 16 V DC or use reverse polarity.
This could cause a fire or damage the transponder.
RWARNING! NEVER cut the DC power cable between
the DC plug at the back of the transponder and fuse holder. If
an incorrect connection is made after cutting, the transponder
may be damaged.
CAUTION: NEVER place the transponder where normal
operation of the vessel may be hindered or where it could
cause bodily injury.
KEEP the transponder at least 1 m (3.3 ft) away from the
vessel’s magnetic navigation compass.
DO NOT use or place the transponder in areas with temperatures below –20°C (–4°F) or above +60°C (+140°F) or, in
areas subject to direct sunlight, such as the dashboard.
DO NOT use harsh solvents such as benzine or alcohol
when cleaning, as they will damage the transponder surfaces.
If the transponder becomes dusty or dirty, wipe it clean with
a soft, dry cloth.
BE CAREFUL! The transponder rear panel will become
hot when operating continuously for long periods of time.
Place the transponder in a secure place to avoid inadvertent
use by children.
BE CAREFUL! The transponder meets IPX7* requirements for waterproof protection. However, once the transponder has been dropped, waterproof protection cannot be
guaranteed because of possible damage to the transponder’s
case or the waterproof seal.
* Except for the DC power and cloning cable connectors.
For U.S.A. only
CAUTION: Changes or modifications to this device, not
expressly approved by Icom Inc., could void your authority to
operate this device under FCC regulations.
Approved Icom optional equipment is designed for optimal
performance when used with an Icom transponder.
Icom is not responsible for the destruction or damage to an
Icom transponder in the event Icom transponder is used with
equipment that is not manufactured or approved by Icom.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
MarineCommander is a trademark of Icom Incorporated.
All other products or brands are registered trademarks or trademarks of their
respective holders.
vi
TABLE OF CONTENTS
vii
FOREWORD.......................................................................... i
IMPORTANT........................................................................... i
EXPLICIT DEFINITIONS........................................................ i
FCC INFORMATION............................................................. ii
SUPPLIED ACCESSORIES.................................................. ii
RADIO OPERATOR WARNING........................................... iii
ABOUT CE........................................................................... iv
PRECAUTIONS.................................................................... vi
TABLE OF CONTENTS....................................................... vii
1 OVERVIEW.......................................................................1
2 PANEL DESCRIPTION.................................................2–6
■ Front panel.....................................................................2
■ Function display.............................................................4
3 PREPARATION..........................................................7–13
■ MMSI code setting.........................................................7
■ Initial setting mode........................................................9
4 BASIC OPERATION.................................................14–22
■ Turning power ON........................................................14
■D
isplay backlight and contrast settings.......................15
■ Plotter display operation..............................................15
■ Target list display operation.........................................16
■ Danger list display operation.......................................17
■ About the detail screen...............................................17
■ Individual DSC call
(Possible only when a transceiver is connected).................22
5 OTHER FUNCTIONS................................................23–27
■ Message......................................................................23
■ Waypoint......................................................................24
■ Lost target...................................................................27
6 MENU MODE OPERATION......................................28–34
■ General.......................................................................28
■ Menu mode items........................................................28
7 INSTALLATION AND CONNECTIONS....................35–42
■ Connections................................................................35
■ Fuse replacement.......................................................38
■ Antenna.......................................................................38
■ Transceiver connection................................................39
■ Mounting the transponder...........................................41
■ MB-75 installation........................................................42
8 MAINTENANCE.......................................................43–45
■ Troubleshooting...........................................................43
■ Error message.............................................................44
■ Diagnostics..................................................................44
9 SPECIFICATIONS AND OPTION...................................46
■ Specifications..............................................................46
■ Option..........................................................................46
10TEMPLATE.....................................................................47
11AtoN CODE AND DESCRIPTION..................................49
OVERVIEW
1
D ABOUT AIS
D AIS Classes
AIS is an acronym for “Automatic Identification System.”
An AIS transponder is a short range data radio unit, used
primarily for collision-risk management and navigation safety.
It automatically transmits and receives vessel information
such as the vessel name, MMSI code, vessel type, position
data, speed, course, destination and more. Information is exchanged among the vessels and/or base stations on the VHF
maritime mobile band. The information helps to identify other
nearby vessels or stations by displaying the received data on
a plotter or a radar screen.
There are four types of AIS stations; vessels, base stations,
Aids to Navigation (AtoN) and Search and Rescue (SAR).
Other vessel
(Class A AIS)
Other vessel
(Class B AIS)
Under the Safety Of Life At Sea (SOLAS) convention, all
SOLAS vessels, as described below, are required to install a
Class A AIS transponder:
• Upwards of 300 gross tonnage engaged on international
voyages.
• Passenger vessels, irrespective of size, engaged on international voyages.
• Upwards of 500 gross tonnage not engaged on international
voyages.
A Class B AIS transponder is designed to be interoperability
with Class A units, but not to impact the Class A network.
Many commercial vessels, and some leisure craft, not classified as requiring a Class A unit, choose to install a Class B
unit to avoid accidents at sea.
Vessel information
Base Station
Your vessel
There are two classes of AIS units, which are installed on
vessels; Class A and Class B.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
(Class B AIS)
1
2
PANEL DESCRIPTION
■ Front panel
Function display (p. 4)
qw
e
r
w
e
t
y
u
qDISPLAY MODE KEY [DISP MODE]
<Common>
➥ Push to switch the display mode between the plotter,
target list and danger list. (pp. 4−6)
➥ While in the Menu mode, push to exit it, and return to
the plotter, target list or danger list display which was
selected before you entered the Menu mode.
wLEFT AND RIGHT KEYS [Ω]/[≈]
<Common>
While in the Menu item setting mode, push to select a
menu option. (pp. 29, 33)
o i Speaker
The angle brackets show common or special display operations, as described below:
• <Common> shows the common operation.
• <In the plotter display> shows the plotter display operation.
• <In the target list display> shows the target list display
operation.
• <In the danger list display> shows the danger list display operation.
2
<In the plotter display>
➥ Push [Ω] to sequentially select each AIS target icon farthest from your vessel (or waypoint, if it is set; see page
24 for setting detail). (p. 15)
➥ Push [≈] to sequentially select each AIS target icon
closest to your vessel (or waypoint, if it is set; see page
24 for setting detail). (p. 15)
• A target box will appear around the selected target or waypoint
icon.
<In the danger list display>
➥ Push [Ω] to sort the AIS target data by CPA (Closest
Point of Approach). (p. 17)
➥ Push [≈] to sort the AIS target data by TCPA (Time to
CPA). (p. 17)
PANEL DESCRIPTION
eUP AND DOWN KEYS [∫]/[√]
<Common>
➥ While in the Menu mode, push to select a menu item.
(pp. 9, 28)
➥ Push to select a voice channel in the voice channel selection screen. (p. 21)
<In the plotter display>
Push to select the display range. (p. 15)
<In the target or danger list display>
Push to select an AIS target in the target or danger list
display. (pp. 16, 17)
rENTER KEY [ENT]
<Common>
➥ Push to display the detail screen of the selected AIS
target. (pp. 15−17)
➥ Push to save the input data. (pp. 8, 10, 15)
➥ Push to enter the Menu item setting mode. (pp. 9, 28)
➥ While in the Menu item setting mode, push to select a
menu option. (pp. 11, 12, 16, 29, 32−34)
➥ While searching for a GPS satellite, push [ENT] to display the GPS information screen. (p. 14, 31)
tMENU KEY [MENU]
<Common>
➥ Push to enter the Menu mode. (pp. 9, 28)
➥ While in the Menu mode, push to exit it, and return to
the plotter, target list or danger list display which was
selected before you entered the Menu mode.
2
yCLEAR KEY [CLEAR]
<Common>
➥ Push to cancel the entered function, or return to the previous screen. (pp. 10, 13, 23)
➥ While in the Menu mode, push to exit it, and return to the
previous screen. (pp. 9, 28)
➥ Push to stop an alarm. (pp. 15−17)
2
uDSC KEY [DSC]
<Common>
➥ When the AIS target is selected, or the detail screen is
displayed, push to display the voice channel selection
screen. (p. 22)
➥ After selecting the voice channel, push to transmit an
Individual DSC call to the selected AIS target. (p. 22)
This function is available only when a transceiver is connected to the transponder. (p. 39)
iPOWER/BRILL KEY [POWER•BRILL]
<Common>
➥ Hold down for 1 second to turn the power ON or OFF.
(p. 14)
• After turning ON the power, the opening screen will appear.
➥ Push to show the display backlight and contrast adjusting screen. (p. 15)
oMAN OVERBOAT KEY [MOB]
<Common>
Hold down for 1 second to set the waypoint. (p. 25)
• The MOB alarm sounds, and a flag icon appears on your current
position.
3
2
PANEL DESCRIPTION
■ Function display
There are three display types; plotter, target list and danger list,
and you can select your desired type using the [DISP MODE] key.
NOTE: When one of the following messages is displayed on
the function display, push [CLEAR] to clear it.
• “PRIORITY INTERRUPTED LAST ATTEMPTS” is displayed
when the transponder cannot make a periodic transmission
because the transponder detects a transmit signal.
• “BASE STATION INHIBITING AIS TX FOR MM MIN”* is displayed when the transmission is inhibited by a base station
for the displayed time period.
*The transmission inhibit period is displayed instead of “MM.”
-“
” is also displayed while transmission is inhibited.
D Plotter display
After the transponder is turned ON, the plotter display automatically appears, if the GPS receiver is connected and it receives
signals from a satellite. It shows the display range and the icons
of the AIS targets.
w
e
q
r
t
y
4
i
u
qDISPLAY TYPE
Shows the selected display type.
• When “N-UP” is displayed, the top of the plotter display represents North.
• When “AC-UP” is displayed, the top of the plotter display represents the direction your course is heading.
wRANGE/CPA INFORMATION
➥ Shows the range information from your vessel to the selected AIS target.
➥ Shows the CPA (Closest Point of Approach) information
of the selected AIS target whose CPA is within 6 nm
(nautical miles) and TCPA (Time to CPA) is within 60
minutes of your vessel.
eBEARING/TCPA INFORMATION
➥ Shows the bearing information from your vessel to the
selected AIS target.
➥ Shows TCPA information of the selected AIS target
whose CPA is within 6 nm (nautical miles) and TCPA is
within 60 minutes of your vessel.
rMESSAGE ICON
Appears when a message is received.
• The message icon stays on the plotter display as long as the
unread message is stored in the RX log memory.
PANEL DESCRIPTION
tTARGET BOX
Shows the selected AIS target (or waypoint, if it is set; see
pages 24–26 for setting detail).
• When a target box appears, push [ENT] to display the detail
screen of the selected AIS target or waypoint.
yYOUR VESSEL ICON
Your vessel icon is displayed in the center of the display.
• When “N-UP” is displayed, the vessel icon automatically points
in the direction you are heading, in 45 degrees steps.
• When “AC-UP” is displayed, the vessel icon constantly points to
the top of the plotter display.
• When your vessel moves less than 2 knots, the icon is displayed
as “ .”
uKEY ENTRY GUIDE
Shows the key entry guide.
➥ Push [Ω] or [≈] to select each AIS target icon (or waypoint), in sequence. (p. 15)
• A target box will appear around the selected target icon.
➥ Push [ENT] to display the detail screen of the selected
AIS target or waypoint. (pp. 15–17)
iDISPLAY RANGE
Shows the selected display range.
• 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24 nm (nautical miles) are
selectable.
2
• Description of the icons
Icon
Description
AIS target: Vessel
The tip of the target triangle automatically points
in the direction it’s heading.
The icon blinks when the AIS target is closer than
your CPA and TCPA settings. (Dangerous target)
AIS target: Lost target*
The target triangle is marked with a diagonal line.
AIS target: Base Station
AIS target: Search and Rescue (SAR)
AIS target: Aids to Navigation (AtoN)
Waypoint
*A vessel is regarded as a “Lost target” after a specified period of time has passed since the vessel last transmitted
data. (p. 27)
The “Lost target” icon disappears from the plotter display 6
minutes and 40 seconds after the vessel was regarded as a
“Lost target.” Ask your dealer for details.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
5
2
PANEL DESCRIPTION
■ Function display (Continued)
D Danger list display
D Target list display
In the plotter display, push [DISP MODE] to switch to the target list display, which shows all AIS targets being detected by
the transponder.
The AIS target data is sorted by the distance from your vessel, and the closest target is located on the top of the list.
In the target list display, push [DISP MODE] to switch to the
danger list display, which helps you to find any dangerous
target whose CPA is within 6 nm (nautical miles) and TCPA is
within 60 minutes of your vessel.
q
q
e
e
w
w
qTHE NUMBER OF TARGETS
Shows the number of AIS targets which are being detected
by the transponder.
wKEY ENTRY GUIDE
Shows the key entry guide.
➥ Push [∫] or [√] to select an AIS target. (p. 16)
➥ Push [ENT] to display the detail screen of the selected
AIS target. (pp. 16, 17)
eTARGET INFORMATION
Shows the following AIS target information:
6
• MMSI code or name, if the name is programmed.
• Range (RNG) from your vessel to the target (unit: nautical mile)
• Bearing (BRG) from your vessel to the target (unit: degree)
qTHE NUMBER OF DANGEROUS TARGETS
Shows the number of AIS targets which are being detected
by the transponder.
wKEY ENTRY GUIDE
Shows the key entry guide.
➥ Push [Ω] or [≈] to sort the danger target data. (p. 17)
➥ Push [ENT] to display the detail screen of the selected
AIS target. (p. 17)
eDANGER TARGET INFORMATION
Shows the following dangerous target information:
• MMSI code or name, if the name is programmed.
• CPA : Closest Point of Approach (unit: nautical mile)
• TCPA: Time to CPA (unit: minute)
PREPARATION
3
■ MMSI code setting
The 9-digit MMSI (Maritime Mobile Service Identity: DSC self
ID) code can be set at power ON. If the MMSI code has already been set, the following steps are not needed. Go to
page 9.
This initial code setting can be performed only once.
After being set, it can be changed by only your dealer or
distributor.
q Hold down [POWER•BRILL] for 1 second to turn ON the
power.
• A long beep sounds, and the opening screen appears.
e After the opening test is completed, “No MMSI” appears
when no MMSI code is set.
• If the MMSI code has already been set, the MMSI code appears.
Go to page 9.
• Push [CLEAR] to skip the setting, and go to the plotter display.
In this case, the transponder operates as just an AIS receiver.
[POWER•BRILL]
w The opening screen displays the results of the opening
test (ROM, RAM and backup data test); “OK” or “NG” (No
Good).
• If “NG” is displayed, hold down [POWER•BRILL] for 1 second to turn
OFF the power, then ON again to reset the transponder. If there is no
change, contact your dealer or service center.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
☞ Continued on the next page.
7
3
PREPARATION
■ MMSI code setting (Continued)
r Push [ENT] to enter the MMSI code setting mode.
tPush [∫] or [√] to input the specific 9-digit MMSI code.
yAfter inputting the 9-digit code, push [ENT].
• The MMSI confirmation screen appears.
• Push [≈] to move the cursor forward.
• Push [Ω] to move the cursor backward.
• Push [CLEAR] to cancel, and go to the plotter display. In this
case, the transponder operates as just an AIS receiver.
[∫], [√],
[Ω], [≈]
[ENT]
[CLEAR]
NOTE: The coast station ID or the group ID cannot be entered as your MMSI code.
• Group ID
: The first one digit is “0.”
• Coast station ID: The first two digits are “0.”
If you enter a code that starts with “0” or “00,” an error beep
sounds after pushing [ENT] in step y.
8
uInput the same MMSI code which was entered in steps t
and y for the confirmation. Then, push [ENT] to save.
i After the MMSI code has been saved, the transponder automatically enters the Initial setting mode. See pages 9 to
13 for setting details.
The Initial setting mode can also be entered from the
Menu mode. (p. 9)
PREPARATION
■ Initial setting mode
The Initial setting mode allows you to set the vessel’s information that is exchanged among the vessels and/or base
stations. And, you can set the seldom-changed NMEA Input/
Output settings.
NOTE: After the MMSI code programming, the transponder automatically enters the Initial setting mode. In this
case, skip steps q and w.
q
Push [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “Initial Setting,” then push [ENT].
e
Push [∫] or [√] to select the desired item, then push [ENT].
rEnter the characters or select the desired option.
The procedures are described on pages 10 to 13.
tRepeat steps e and r to set other items.
yPush [CLEAR] to exit the Initial setting mode, and return
to the Menu mode.
uPush [CLEAR] to exit the Menu mode.
[∫]
[ENT]
[√]
D MMSI code
Enter the vessel’s MMSI code.
See page 7 for setting details.
• If the MMSI code has already been set, you cannot change this.
D Name
Enter the vessel’s name of up to 20 characters.
See page 13 for setting details.
D Call Sign
Enter the Call Sign of up to 7 characters.
The Call Sign is a unique designation ID for a station.
See page 13 for setting details.
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
[CLEAR]
[MENU]
9
3
PREPARATION
■ Initial setting mode (Continued)
D Internal/External GPS Antenna Position
D Type of Ship
Set these measurements to indicate the internal and/or external GPS antenna position on the vessel.
Select your vessel type.
• Internal GPS antenna : The GPS antenna which is connected to
the [GPS] connector.
• External GPS antenna: The GPS antenna which is connected to one
of the NMEA lines. (p. 37)
➥Push [∫] or [√] to select your vessel type from the list,
then push [ENT] to save and return to the Initial setting
mode.
[∫]
[ENT]
qPush [∫] or [√] to select “A,” “B,” “C” or “D.”
• A : Bow to Antenna
• B : Stern to Antenna
• C : Port side to Antenna
• D : Starboard side to Antenna
• Push [CLEAR] to cancel and return to the previous screen.
wPush [Ω] or [≈] to input the value into that item.
A and B: Between 0 and 511 meters (0 and 1676.5 feet)
C and D: Between 0 and 63 meters (0 and 206.6 feet)
eRepeat steps q and w to input other values.
rPush [ENT] to save and return to the Initial setting mode.
• Type of Ship List
30 Fishing
52 Tugs
31 Towing
53 Port tender
32 Towing & two < 200m
54 Vessels with anti pollution
[ENT]
33 Engaged in Dredging
55 Law enforcements Vessel
[CLEAR]
34 Engaged in Diving
58 Medical Transports
35 Engaged in Military
59 Ships RR Resolution NO18
36 Sailing
60 Passenger Ship
37 Pleasure Craft
70 Cargo Ship
50 Pilot
80 Tanker
[∫], [√],
[Ω], [≈]
This screen shows the internal GPS antenna set screen.
10
[√]
To show the external GPS antenna set screen, select “Set
EXT GPS POS” in the “Initial Setting” mode. (p. 9)
51 Search & Rescue Vessel
PREPARATION
D NMEA Input/Output ports
• NMEA1/NMEA2/NMEA3 data speed
The data communication speed (baud rate) can be set for
each Input/Output port; NMEA1 and NMEA3.
NOTE: The data communication speed of NMEA2 is fixed
to 38400 bps. NMEA2 is used for communication between
the transponder and the Icom MarineCommander™ system or a GPS receiver.
qPush [∫] or [√] to select “NMEA1” or “NMEA3.”
• NMEA1: Used for communication between the transponder and
a transceiver or a GPS receiver. (Default: 4800 bps)
• NMEA3: Used for communication between the transponder and
a navigational equipment or a GPS receiver.
(Default: 4800 bps)
• You cannot select “NMEA2.”
wPush [ENT] to select the data communication speed between 4800 bps and 38400 bps into that item.
• You can also select the option by pushing [Ω] or [≈].
eRepeat steps q and w to set another port.
rPush [CLEAR] to save and return to the Initial setting mode.
[∫], [√],
[Ω], [≈]
3
• GPS Input1/GPS Input2/GPS Input3
Set the NMEA1, NMEA2 and NMEA3 Input ports’ capability.
qPush [∫] or [√] to select “GPS Input1,” “GPS Input2” or
“GPS Input3.”
• “GPS Input1” is for the NMEA1, “GPS Input2” is for the NMEA2
and “GPS Input3” is for the NMEA3 ports setting.
wPush [ENT] to toggle this function ON or OFF.
• You can also turn the function ON by pushing [≈], or OFF by
pushing [Ω].
ON : The GPS information that is received from the external GPS receiver of the selected port is sent to
the transponder.
(Default for “GPS Input2” and “GPS Input3”)
OFF : The GPS information that is received from the external GPS receiver of the selected port is not sent
to the transponder. (Default for “GPS Input1”)
eRepeat steps q and w to set other ports’ capability.
rPush [CLEAR] to save and return to the Initial setting
mode.
[∫], [√],
[Ω], [≈]
[ENT]
[ENT]
[CLEAR]
[CLEAR]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
11
3
PREPARATION
■ Initial setting mode
D NMEA Input/Output ports (Continued)
• AIS Output
Set the NMEA2 output port’s capability.
This function should normally be set to “AIS.”
qPush [∫] or [√] to select “AIS Output.”
wPush [ENT] to select either “AIS” or “AIS+GPS.”
• You can also select the option by pushing [Ω] or [≈].
AIS
: The NMEA2 output port sends only the AIS
information to the connected device. (Default)
AIS+GPS : The NMEA2 output port sends both the AIS
and GPS information to the connected device.
This setting is recommended for use in an area
where there are few vessels. In areas crowded
with AIS equipped vessels, a large amount of
information is received. The output of GPS information has priority, so the NMEA2 output
port may not send some AIS information correctly. However, the transponder displays the
AIS information on it’s LCD correctly.
ePush [CLEAR] to save and return to the Initial setting
mode.
[∫], [√],
[Ω], [≈]
[ENT]
[CLEAR]
12
• Remote ID
Set a Remote ID number between 80 and 89.
The Remote ID is included in the sentence of the format for
the Icom own NMEA.
qPush [∫] or [√] to select “Remote ID.”
wPush [Ω] or [≈] to set a Remote ID number between 80
and 89.
ePush [CLEAR] to save and return to the Initial setting
mode.
[∫], [√],
[Ω], [≈]
[CLEAR]
PREPARATION
3
D Name and Call Sign settings
qPush [∫] or [√] to select the “Set Name” or “Set Call Sign”
that you want to program, then push [ENT] to enter the setting mode.
[∫]
[ENT]
[∫], [√],
[Ω], [≈]
[√]
[ENT]
wPush [∫], [√], [Ω] or [≈] to select the desired character in
the table, then push [ENT] to input it.
e Repeat step w to input all characters.
r Push [∫], [√], [Ω] or [≈] to select “FINISH,” then push
[ENT] to save and return to the Initial setting mode.
• Select “
,” then push [ENT] to move the cursor forward.
• Select “
,” then push [ENT] to move the cursor backward.
• Select “SPACE,” then push [ENT] to input a space.
• Select “DELETE,” then push [ENT] to delete a character.
• Push [CLEAR] to cancel and return to the previous screen.
[∫], [√],
[Ω], [≈]
[ENT]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
[CLEAR]
13
4
BASIC OPERATION
■ Turning power ON
IMPORTANT: BE SURE to connect the GPS receiver to
the transponder before turning the power ON. (p. 35)
e After the opening test is completed, the MMSI code appears, if the code has already been set.
• “No MMSI” appears when no MMSI code is set. (p. 7)
q Hold down [POWER•BRILL] for 1 second to turn ON the
power.
• A long beep sounds, and the opening screen appears.
[POWER•BRILL]
r The GPS search display appears while searching for a
GPS satellite.
w The opening screen displays the results of the ROM, RAM
and backup data test, “OK” or “NG” (No Good).
14
• While searching, the GPS information screen can be displayed
by pushing [ENT], or you can enter the Menu mode by pushing
[MENU]. (pp. 28, 31)
• If “NG” is displayed, hold down [POWER•BRILL] for 1 second to turn
OFF the power, then ON again to reset the transponder. If there is no
change, contact your dealer or service center.
tWhen the GPS receiver receives signals from a satellite,
the transponder automatically displays the position data
on the plotter display. (p. 15)
BASIC OPERATION
■D
isplay backlight and
contrast settings
You can adjust the display backlight and contrast settings.
The display backlight lights the function display and keys, and
is convenient for nighttime operation.
Also, you can adjust the display contrast between objects and
the background.
■ Plotter display operation
When the plotter display is selected, the display range and the
icons of the AIS targets appear. You can change the display range
and type (North up or COG up) to suit your operating style.
qPush [DISP MODE] several times to select the plotter display.
wPush [∫] or [√] to select the desired display range.
qPush [POWER•BRILL] to display the popup screen to adjust the display backlight and contrast level.
wPush [∫] or [√] to select “Backlight” or “Contrast,” whichever one you want to adjust.
ePush [Ω] or [≈] to adjust the level.
• Backlight: Between 1 and 7, or OFF
• Contrast : Between 1 and 8
rPush [ENT] to save the settings and turn OFF the popup
screen.
• If no key operation is performed for 5 seconds, the backlight and
contrast levels are saved, and the popup screen automatically
turns OFF.
Convenient!
Each push of [POWER•BRILL] after the popup screen is displayed, also adjusts the display backlight level.
4
• 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24 nm (nautical miles) are
selectable.
ePush [≈] to sequentially select each AIS target icon closest to your vessel (or waypoint, if it is set; see page 24 for
setting detail), in sequence.
Or, push [Ω] to select each AIS target (or waypoint) icon
farthest from your vessel, in sequence.
• A target box will appear around the selected target (or waypoint)
icon.
• Shows the range and bearing information from your vessel to the
selected AIS target.
• Shows the CPA (Closest Point of Approach) and TCPA (Time to
CPA) information of the selected AIS target whose CPA is less
than 6 nm (nautical miles) and TCPA is less than 60 minutes to
your vessel.
rPush [ENT] to display it’s detail screen. (p. 17)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
NOTE: The alarm buzzer sounds when a malfunction occurs or an AIS target is closer than your CPA and TCPA
settings, depending on the presetting. (pp. 29, 30, 33, 44)
➥To stop the alarm buzzer, push [CLEAR].
• If the popup screen is displayed, push [CLEAR] again to turn it OFF.
15
4
BASIC OPERATION
■ Plotter display operation (Continued)
D Setting the display type (North up/COG up)
Select the display type between “North up” and “COG up.”
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “North up/COG up,” then push
[ENT].
ePush [ENT] to select either “North up” or “COG up.”
• You can also select the option by pushing [Ω] or [≈].
North up: The top of the plotter display represents North.
COG up : The top of the plotter display represents the direction your course is heading.
rPush [CLEAR] to save and return to the Menu mode.
tPush [CLEAR] to exit the Menu mode.
[∫], [√],
[Ω], [≈]
[ENT]
[CLEAR]
[MENU]
16
■ Target list display operation
The target list display shows all AIS targets being detected
by the transponder, including their range and bearing information.
The AIS target data is sorted by the distance from your vessel, and the closest target is located on the top of the list.
Their range and bearing information is automatically updated
every 5 seconds, then the AIS target data is sorted.
qPush [DISP MODE] several times to select the target list
display.
wPush [∫] or [√] to select the desired AIS target.
ePush [ENT] to display it’s detail screen. (p. 17)
NOTE: The alarm buzzer sounds when a malfunction occurs or an AIS target is closer than your CPA and TCPA
settings, depending on the presetting. (pp. 29, 30, 33, 44)
➥To stop the alarm buzzer, push [CLEAR].
• If the popup screen is displayed, push [CLEAR] again to turn
it OFF.
BASIC OPERATION
4
■ Danger list display operation
■ About the detail screen
The danger list display shows any dangerous target whose
CPA (Closest Point of Approach) distance is less than 6 nm
(nautical miles), and TCPA (Time to CPA) time is less than 60
minutes to your vessel.
The dangerous target data is sorted by CPA or TCPA (you
can choose either; see step q).
Their CPA and TCPA information is automatically updated
every 5 seconds, then the dangerous target data is sorted.
The detail screen shows information about the selected AIS
target. The contents differ, depending on the AIS class.
In the detail screen, pushing [CLEAR] returns to the previous screen, which was displayed before entering the details
screen.
See pages 18 to 21 for the detail screen of each AIS class.
qPush [DISP MODE] several times to select the danger list
display.
• Push [Ω] to sort the AIS target data by CPA.
• Push [≈] to sort the AIS target data by TCPA.
wPush [∫] or [√] to select the desired AIS target.
ePush [ENT] to display it’s detail screen. (See to the right)
NOTE: The alarm buzzer sounds when a malfunction occurs or an AIS target is closer than your CPA and TCPA
settings, depending on the presetting. (pp. 29, 30, 33, 44)
➥To stop the alarm buzzer, push [CLEAR].
• If the popup screen is displayed, push [CLEAR] again to turn
it OFF.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
4
BASIC OPERATION
■ About the detail screen (Continued)
D The detail screens of “Class A” vessels
Detail screen 3/6
• AIS Class
• MMSI Code
• Ship Name
• Country Name
• Call Sign
• IMO Number
• A: Bow to Antenna
• B: Stern to Antenna
• C: Port side to Antenna
• D: Starboard side to Antenna
• Length
• Beam
• Draught
• CPA
• TCPA
• Latitude
• Longitude
• Speed Over Ground
• Course Over Ground
• Heading
• Position Accuracy
(H: High, L: Low)
• Range
• Bearing
• Rate Of Turn
Detail screen 4/6
18
• Type of Ship
• Navigation Status
• Destination
• Date
• Time
BASIC OPERATION
D The detail screens of “Class B” vessels
Detail screen 3/5
• AIS Class
• MMSI Code
• Ship Name
• Country Name
• Call Sign
• A: Bow to Antenna
• B: Stern to Antenna
• C: Port side to Antenna
• D: Starboard side to Antenna
• Length
• Beam
• Vendor ID
• CPA
• TCPA
• Latitude
• Longitude
• Speed Over Ground
• Course Over Ground
• Heading
• Position Accuracy
(H: High, L: Low)
• Range
• Bearing
• Type of Ship
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Detail screen 4/5
19
4
BASIC OPERATION
■ About the detail screen (Continued)
D The detail screens of a “Base Station”
• AIS Class
• MMSI Code
• Latitude
• Longitude
• Position Accuracy
(H: High, L: Low)
• Range
• Bearing
20
D The detail screens of an “SAR”
• AIS Class
• MMSI Code
• Latitude
• Longitude
• Speed Over Ground
• Course Over Ground
• Position Accuracy
(H: High, L: Low)
• Range
• Bearing
• Altitude
BASIC OPERATION
4
D The detail screens of an “AtoN”
• AIS Class
• MMSI Code
• CPA
• TCPA
• Latitude
• Longitude
• Position Accuracy
(H: High, L: Low)
• Range
• Bearing
Detail screen 3/4
Detail screen 2/4
• A: Bow to Antenna
• B: Stern to Antenna
• C: Port side to Antenna
• D: Starboard side to Antenna
• Length
• Beam
• Position Indicator
(ON POS : ON Position,
OFF POS: OFF Position)
• AtoN existence
(REAL, VIRTUAL)
• Type of AtoN
(See page 49)
• Description of AtoN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
21
4
BASIC OPERATION
■ Individual DSC call (Possible only when a transceiver is connected)
When a transceiver* is connected to the transponder, you can
transmit an Individual DSC call without needing to enter the
vessel’s MMSI code, by simply selecting it’s AIS target and
the voice channel you wish to use on the transponder.
The transceiver will use the transponder’s data information
and make the DSC call on channel 70, then wait for the target
vessel to acknowledge it. After receiving the acknowledgement ‘Able to comply,’ use the transceiver to communicate with
the target vessel on the predetermined voice channel.
*See the leaflet that comes with the transponder for details of the transceivers which can operate with this function.
[∫]
[√]
[DSC]
See pages 39 and 40 for connecting instructions.
NOTE: The data communication speed (baud rate) of
NMEA1 must be set to 4800 bps to send an Individual
DSC call using the transponder. (p. 11)
qSelect the desired AIS target on the plotter, target list or
danger list display. (pp. 15–17)
• You can also go to the next step whenever the detail screen of
the AIS target is displayed.
wPush [DSC] to display the voice channel selection screen,
then push [∫] or [√] to select the desired voice channel.
22
• Voice channels are already preset into the transponder in recommended order.
OTE: When a base station is selected in step q, a
N
voice channel will be specified by the base station,
therefore you cannot change the channel. The transponder will display “Voice Channel is specified by the
Base station,” in this case.
ePush [DSC] to make the Individual DSC call.
• “DSC Transmitting” appears.
• If Channel 70 is busy, the transceiver stands by until the channel
becomes clear.
• If the transceiver cannot make the call, “DSC Transmission FAILED”
appears.
rAfter making the Individual DSC call, “DSC Transmission
COMPLETED” appears.
tPush [CLEAR] to return to the previous screen before you
entered the voice channel selection screen in step w.
yAfter receiving the acknowledgement from the AIS target,
use the transceiver to communicate. See the transceiver’s
manual for details.
OTHER FUNCTIONS
5
■ Message
D Receiving a message
D Message logs
A safety-related message of up to 161 characters can be received from an AIS equipped vessel in the area.
When a message is received, a beep sounds three times,
and the message icon appears on the plotter display. (The
message icon does not appear on the target list or danger
list display.)
The contents of the message can be checked in the receive
message log, as described to the right.
The message icon stays on the plotter display as long as the
unread message is stored in the RX log memory.
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “Message,” then push [ENT].
ePush [∫] or [√] to select “RX Log,” then push [ENT].
rPush [∫] or [√] to select the message that you want to
read, then push [ENT].
The transponder automatically stores the last 20 received
messages in the log memory.
The oldest message is automatically deleted when a new
message is received.
NOTE: The transponder automatically stores the received
messages in the RX log memory. (See to the right)
Appears
• The contents of the selected message are displayed.
tPush [CLEAR] to return to the previous screen.
yPush [CLEAR] three times to exit the Menu mode.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Plotter display
23
5
OTHER FUNCTIONS
■ Waypoint
D Display a waypoint list
Up to 100 waypoints can be stored in the waypoint list.
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “Waypoint,” then push [ENT].
ePush [∫] or [√] to select “List,” then push [ENT].
rPush [∫] or [√] to select the desired waypoint.
• Push [Ω] to sort the waypoint data by Name.
• Push [≈] to sort the waypoint data by Range.
tPush [ENT] to display the detail screen of the selected
waypoint.
D Add a waypoint
The position information that you want to memorize can be
added as a waypoint.
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “Waypoint,” then push [ENT].
ePush [∫] or [√] to select “Add,” then push [ENT].
• Your current position information is displayed.
rPush [∫] or [√] to select “Name,” then push [ENT].
t Push [∫], [√], [Ω] or [≈] to select the desired character in
the table, then push [ENT] to input it.
• Select “
,” then push [ENT] to move the cursor forward.
• Select “
,” then push [ENT] to move the cursor backward.
• Select “SPACE,” then push [ENT] to input a space.
• Select “DELETE,” then push [ENT] to delete a character.
• Push [CLEAR] to cancel and return to the previous screen.
[∫], [√],
[Ω], [≈]
[ENT]
[CLEAR]
yPush [CLEAR] to return to the previous screen.
uPush [CLEAR] three times to exit the Menu mode.
24
y Repeat step t to input a waypoint name of up to 10 characters.
u Push [∫], [√], [Ω] or [≈] to select “FINISH,” then push
[ENT] to set and return to the previous screen.
OTHER FUNCTIONS
iPush [∫] or [√] to select “LAT:,” then push [ENT].
o Push [∫], [√], [Ω] or [≈] to set the desired latitude data in
the table, then push [ENT] to input it.
[∫], [√],
[Ω], [≈]
[ENT]
• Select “
,” then push [ENT] to move the cursor forward.
• Select “
,” then push [ENT] to move the cursor backward.
• Select “N,” then push [ENT] to input N; North latitude.
• Select “S,” then push [ENT] to input S; South latitude.
• “W” and “E” cannot be input.
• Push [CLEAR] to cancel and return to the previous screen.
[∫], [√],
[Ω], [≈]
[ENT]
[CLEAR]
5
[CLEAR]
!3 Push [∫], [√], [Ω] or [≈] to select “FINISH,” then push
[ENT] to set and return to the previous screen.
!4Push [∫] or [√] to select “SAVE,” then push [ENT] to save
the waypoint data and return to the “WAYPOINT” screen.
• Push [CLEAR] to cancel and return to the previous screen.
[∫]
[ENT]
!0 Push [∫], [√], [Ω] or [≈] to select “FINISH,” then push
[ENT] to set and return to the previous screen.
!1Push [∫] or [√] to select “LON:,” then push [ENT].
!2 Push [∫], [√], [Ω] or [≈] to set the desired longitude data
in the table, then push [ENT] to input it.
• Select “
,” then push [ENT] to move the cursor forward.
• Select “
,” then push [ENT] to move the cursor backward.
• Select “W,” then push [ENT] to input W; West longitude.
• Select “E,” then push [ENT] to input E; East longitude.
• “N” and “S” cannot be input.
• Push [CLEAR] to cancel and return to the previous screen.
[√]
[CLEAR]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
!5Push [CLEAR] twice to exit the Menu mode.
Convenient!
Each time you hold down of [MOB] also adds a waypoint. See
page 26 to edit the waypoint data.
25
5
OTHER FUNCTIONS
■ Waypoint (Continued)
D Edit a waypoint
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “Waypoint,” then push [ENT].
ePush [∫] or [√] to select “Edit,” then push [ENT].
u Enter a waypoint name, latitude data and longitude data,
as described in steps t to !3 of “D Add a Waypoint” on
pages 24 and 25.
iPush [∫] or [√] to select “SAVE,” then push [ENT] to save
the edited data and return to the “EDIT WAYPOINT” list
screen.
A waypoint’s name, latitude and longitude data can be edited.
• The “EDIT WAYPOINT” list is displayed.
rPush [∫] or [√] to select the desired waypoint.
• Push [Ω] to sort the waypoint data by Name.
• Push [≈] to sort the waypoint data by Range.
tPush [ENT] to enter the edit item selection screen.
• Push [CLEAR] to cancel and return to the previous screen.
[∫]
[ENT]
[√]
[CLEAR]
oPush [CLEAR] three times to exit the Menu mode.
yPush [∫] or [√] to select the top item (waypoint name),
then push [ENT].
26
5
OTHER FUNCTIONS
D Delete a waypoint
A waypoint can be deleted from the waypoint list.
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “Waypoint,” then push [ENT].
ePush [∫] or [√] to select “Delete,” then push [ENT].
• The “DELETE WAYPOINT” list is displayed.
rPush [∫] or [√] to select the desired waypoint.
• Push [Ω] to sort the waypoint data by Name.
• Push [≈] to sort the waypoint data by Range.
t
Push [ENT] to display the detail screen of the selected waypoint.
yPush [ENT] to display the confirmation screen.
u Push [Ω] or [≈] to select “OK,” then push [ENT] to delete the selected waypoint data and return to the “DELETE
WAYPOINT” list screen.
• Select “Cancel” to cancel deleting.
[ENT]
[≈]
[Ω]
iPush [CLEAR] three times to exit the Menu mode.
■ Lost target
A vessel is regarded as a “Lost target” after a specified period
of time has passed since the vessel last transmitted data, as
described below.
The “Lost target” icon disappears from the plotter display
6 minutes and 40 seconds after the vessel was regarded as a
“Lost target.” Ask your dealer for details.
The criteria to become a Lost target:
Vessel type
Except
Class B
Class B
Except Class B: Vessel is at anchor, moored
and moving less than 3 knots
18 min. 18 min.
1
Class B
: Vessel is moving less than
2 knots
Vessel is at anchor, moored and moving
1 min.
more than 3 knots
N/A
Vessel is moving between 0 and 14 knots
3 (Except Class B), or between 2 and 14 knots 1 min.
(Class B)
3 min.
Vessel is moving between 0 and 14 knots
1 min.
while changing course
N/A
2
4
5 Vessel is moving between 14 and 23 knots 36 sec.
90 sec.
Vessel is moving between 14 and 23 knots
6
36 sec.
while changing course
N/A
7 Vessel is moving more than 23 knots
8
12 sec.
Vessel is moving more than 23 knots while
12 sec.
changing course
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
30 sec.
N/A
27
6
MENU MODE OPERATION
■ General
■ Menu mode items
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select the desired item, then push [ENT].
eSelect the desired option or check the screen contents.
The procedures are described on pages 29 to 34.
The Menu mode contains the following items.
• Some items are not described in this section. See the list to the
right for the specified pages.
rRepeat steps w and e to select or check other items.
tPush [CLEAR] to exit the Menu mode.
Item
North up/COG up*
Ref.
p. 16
CPA/TCPA
Item
Ref.
User Setting
• RCV MSG BUZZ
p. 33
• Alarm
p. 29
• Internal GPS
p. 33
• Slow Warn
p. 29
- SBAS Function
p. 34
• CPA, TCPA
p. 30
- SBAS Search
p. 34
- SBAS Satelite
p. 34
Message
Initial Setting
[∫]
[ENT]
• RX Log*
• Set MMSI*
pp. 7, 9
[√]
• List*
p. 24
• Set Name*
pp. 9, 13
[CLEAR]
• Add*
p. 24
• Set Call Sign*
pp. 9, 13
• Edit*
p. 26
• Set INT GPS POS*
p. 10
• Delete*
p. 27
• Set EXT GPS POS*
p. 10
Own Static
p. 30
• Set Type of Ship*
p. 10
Own Dynamic
p. 31
• Set Input/Output*
p. 11
GPS Information
p. 31
Channel Information
p. 34
Alarm Status
p. 32
Diagnostics
[MENU]
p. 23
Waypoint
User Setting
• Monitor Test*
p. 44
• Key Beep
p. 32
• Transponder Test*
p. 45
• Alarm Buzzer
p. 33
• Version Information*
p. 45
*These items are not described in this section. See the specified page.
28
MENU MODE OPERATION
6
D CPA/TCPA
• Alarm
You can turn the collision alarm function ON or OFF.
qPush [∫] or [√] to select “Alarm.”
wPush [ENT] to toggle this function ON or OFF.
• You can also turn ON the function by pushing [≈], or OFF by
pushing [Ω].
ON : “COLLISION ALARM” appears on the display, and
the alarm buzzer sounds* repeatedly when an AIS
target is closer than your CPA and TCPA settings, as
explained to page 30. (default)
*The alarm buzzer sounds only when the alarm buzzer
function is turned ON. (p. 33)
OFF: The collision alarm function is OFF.
ePush [CLEAR] to save and return to the Menu mode.
[∫], [√],
[Ω], [≈]
[ENT]
• Slow Warn
The GPS receiver calculated COG data of a vessel that is at
anchor or drifting is unreliable, and therefore the CPA and TCPA
data may not be calculated correctly. If a vessel is anchored in
your alarm zone, the unreliable data can cause the collision
alarm to sound many times, even if there is no real danger. To
prevent this, when the anchored vessel’s SOG is less than this
set value, the Slow Warn function assumes that vessel’s COG
is fixed towards your vessel and an alarm will sound.
qPush [∫] or [√] to select “Slow Warn.”
wPush [Ω] or [≈] to input the value between 0.1 and 4.9 kt
(in 0.1 kt steps), or select OFF. (default: 1.0 kt)
ePush [CLEAR] to save and return to the Menu mode.
[∫], [√],
[Ω], [≈]
[CLEAR]
[CLEAR]
NOTE: If other vessels at anchor or drifting come into your
alarm zone, the Slow Warn alarm will sound again. Only if
the previous vessel disappears from the Dangerous List
(pp. 6, 17), and then re-enters the list, can a new Slow
Warn or regular alarm sound, depending on the vessels
SOG, or CPA and TCPA. The Slow Warn function operates
in the same way if your vessel is at anchor and other vessels enter your alarm zone area.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
29
6
MENU MODE OPERATION
■ Menu mode items
D CPA/TCPA (Continued)
• CPA, TCPA
Enter CPA (Closest Point of Approach) and TCPA (Time to
CPA) values.
These settings help you find a dangerous target to avoid a
collision. The icon blinks on the plotter display and/or the
alarm buzzer sounds, when the AIS target is closer than your
CPA and TCPA settings.
qPush [∫] or [√] to select either “CPA” or “TCPA.”
wPush [Ω] or [≈] to input the value into that item.
• CPA : Between 0.1 and 6.0 nm (in 0.1 nm steps)
(default: 1.5 nm)
• TCPA: Between 1 and 60 minutes (in 1 minute steps)
(default: 20 min)
eRepeat steps q and w to input the value into the other
item.
rPush [CLEAR] to save and return to the Menu mode.
[∫], [√],
[Ω], [≈]
[ENT]
[CLEAR]
30
D Own Static
This screen shows your static vessel information such as
MMSI code, Vessel Name, Call Sign, Internal/External GPS
antenna position and Type of Ship.
qW
hen the Own Static screen is displayed, push [≈] to select the next page, or push [Ω] to select the previous page.
wPush [CLEAR] to return to the Menu mode.
MENU MODE OPERATION
6
D GPS Information
D Own Dynamic
This screen shows your dynamic vessel information such as
Latitude and Longitude data, SOG, COG, GPS receiver type,
UTC date and time, PA, RAIM (Receiver Autonomous Integrity Monitoring) function availability and Latitude and Longitude error data.
The GPS Information screen shows the viewable GPS satellite’s information, when the internal or external* GPS receiver
is connected.
*Only when the transponder receives the sentence format
“GSA” or “GSV” from the external GPS receiver.
• An internal GPS has no RAIM function. When the internal GPS is
used, “RAIM,” “LAT ERROR” and “LON ERROR” are not displayed.
• An external GPS requires a RAIM function. When the external GPS
is used, “RAIM,” “LAT ERROR” and “LON ERROR” are displayed.
qWhen the GPS Information screen is displayed, push [≈]
to select the next page, or push [Ω] to select the previous
page.
qWhen the Own Dynamic screen is displayed, push [≈] to
select the next page, or push [Ω] to select the previous
page.
wPush [CLEAR] to return to the Menu mode.
When a non-differential GPS
receiver is connected, PA is
normally ‘L.’ However, if the
values of “LAT ERROR” and
“LON ERROR” are less than
5.0 meters (16.4 feet), PA
changes to ‘H.’
When a differential GPS receiver is connected, PA is
normally ‘H.’ However, if the
values of “LAT ERROR” and
“LON ERROR” are more
than 15.0 meters (49.2 feet),
PA changes to ‘L.’
• The icons of the satellites being used, blink.
The GPS antenna of your vessel is
located in the center of the North,
South, East and West screen, and
the visible GPS satellite icons are
displayed.
SAT : Satellite number
LEVEL: Signal strength level
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
wPush [CLEAR] to return to the Menu mode.
31
6
MENU MODE OPERATION
■ Menu mode items (Continued)
D Alarm Status
The Alarm Status screen shows the type, date and time of the
last 25 malfunctions that were detected.
Even if the alarm buzzer function is turned OFF, the alarm
status is displayed here. (p. 33)
qWhen the Alarm Status screen is displayed, push [∫] or
[√] to scroll the screen.
wPush [CLEAR] to return to the Menu mode.
[∫]
Time
Date
[√]
Alarm type
[CLEAR]
D User Setting
The User setting mode allows you to set the seldom-changed
settings, and you can “customize” the transponder operation
to suit your preferences and operating style.
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “User Setting,” then push [ENT].
ePush [∫] or [√] to select the desired item, then push [ENT].
rSelect the desired option, shown in the Menu below.
The procedures are described to the right and continued
on the next page.
tRepeat steps e and r to select other items.
yPush [CLEAR] to save and return to the Menu mode.
uPush [CLEAR] to exit the Menu mode.
[∫]
[ENT]
[√]
• Description of the Alarm type
Alarm type
GPS
RX
CH A
CH B
TX
ANT
32
Description
[CLEAR]
[MENU]
Appears when “GPS Malfunction” is detected.
Appears when “RX Malfunction” is detected.
Appears when “CH A Noise Level Malfunction” is
detected.
Appears when “CH B Noise Level Malfunction” is
detected.
<SETTING ITEMS>
• Key Beep
You can select the silent operation, or you can have confirmation beeps sound when you push a key.
Appears when “TX Malfunction” is detected.
➥Push [ENT] to toggle this function ON or OFF.*
ON : A beep sounds when pushing a key. (default)
OFF: The key beep is OFF. (Silent operation)
Appears when “Antenna Open or Short Malfunction”
or “Antenna High VSWR Malfunction” is detected.
MENU MODE OPERATION
• Alarm Buzzer
Turn the alarm buzzer function ON or OFF.
➥Push [ENT] to toggle this function ON or OFF.*
ON : The alarm buzzer sounds when a malfunction occurs or an AIS target is closer than your CPA and
TCPA settings*. (default)
*The alarm buzzer sounds only when the collision alarm
function is turned ON. (p. 29)
OFF: The alarm buzzer is OFF.
• Received Message Buzzer (RCV MSG BUZZ)
Turn the received message buzzer function ON or OFF.
➥Push [ENT] to toggle this function ON or OFF.*
ON : The buzzer sounds three times when a message is
received. (default)
OFF: The received message buzzer is OFF.
• Internal GPS
The Internal GPS setting mode allows you to set the internal
GPS settings.
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “User Setting,” then push [ENT].
ePush [∫] or [√] to select “Internal GPS,” then push [ENT].
rPush [∫] or [√] to select the desired item, then push [ENT].
tSelect the desired option, shown in the Menu below.
The procedures are described to the right and continued
on the next page.
yRepeat steps r and t to select other items.
uPush [CLEAR] to save and return to the User Setting
mode.
iPush [CLEAR] twice to exit the Menu mode.
[∫]
[ENT]
[√]
[CLEAR]
*You can also turn ON the function by pushing [≈], or OFF
by pushing [Ω].
6
[MENU]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
33
6
MENU MODE OPERATION
■ Menu mode items
D User Setting (Continued)
<SETTING ITEMS>
- SBAS (Satellite Based Augmentation System) Function
The SBAS transmits signals to correct errors and improve
accuracy and reliability in data received from regular GPS
satellites. When this function is ON, the transponder uses the
corrected data.
➥Push [ENT] to toggle this function ON or OFF.
• You can also turn ON the function by pushing [≈], or OFF by
pushing [Ω].
ON : The SBAS function is ON. (default)
OFF: The SBAS function is OFF.
➥Push [Ω] or [≈] to select an SBAS Satellite number between 120 and 138. (default: 120)
D Channel information
- SBAS Search
Set the SBAS search function to “Manual” or “Auto.”
This function should normally be set to “Auto.”
The channel information screen shows the channels 2087
and 2088 information in which safety-related messages are
transmitted to, and received from, the AIS targets.
The channel to be used is automatically set according to the
message received from an AIS Base Station.
➥Push [ENT] to select either “Manual” or “Auto.”
➥Push [CLEAR] to return to the Menu mode.
• You can also select the option by pushing [Ω] or [≈].
Manual: You have to manually select the SBAS satellite.
This option can be useful when your vessel is in
an area where 2 satellite zones overlap.
Auto : The transponder automatically searches for the
SBAS satellite that is determined according to the
position of your vessel. (default)
34
- SBAS Satellite
When “Manual” option is selected in the SBAS Search item,
you should manually select the SBAS Satellite which covers
the zone your vessel is monitoring.
[CLEAR]
INSTALLATION AND CONNECTIONS
7
■ Connections
About the installation distance from the compass:
KEEP the transponder at least 1 m (3.3 ft) away from the
vessel’s magnetic navigation compass.
w
q
eDC POWER CONNECTOR
Connects the supplied DC power cable between this connector and a 12 V power source.
rHIGH-DENSITY D-SUB 15 PIN (NMEA IN/OUT)
Connects an Icom MarineCommander™ system, navigation equipment, external GPS receiver, etc. using the supplied OPC-2014 nmea connector cable.
See page 37 for the pin assignment.
e
r
y
t
qCLONING CABLE CONNECTOR
Connects the cloning cable from this connector to a PC.
Ask your dealer for details.
wINTERNAL GPS RECEIVER CONNECTOR
Connects to the MXG-5000 to receive position data and
transmit it with other AIS information.
OTE: Important notes and how to install the MXGN
5000 are described on the instruction sheet that comes
with it. Be sure to read them before installing and operating the MXG-5000.
Requirements of the external GPS:
• The datum of the external GPS receiver must be
“WGS-84.”
• GBS sentence can be input using the RAIM function.
• The external GPS antenna must be installed within
26 m (85.3 ft) of the internal GPS antenna.
CAUTION: After connecting the DC power cable and
NMEA connector cable leads, cover the cable and leads
with a rubber vulcanizing tape, to prevent water seeping
into the transponder.
Rubber vulcanizing tape
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
35
7
INSTALLATION AND CONNECTIONS
■ Connections (Continued)
tGROUND TERMINAL
Connects to a vessel ground to prevent electrical shocks
and interference from other equipment occurring. Use a
self-tapping screw (3 × 8 mm).
yANTENNA CONNECTOR
Connects to a marine VHF antenna with a PL-259 connector for AIS signal transmission and reception. (p. 38)
36
CAUTION: Transmitting without an antenna may damage the transponder.
D High-density D-sub 15 pin assignment
t r e w q
!0 o i u y
!5 !4 !3 !2 !1
Rear panel view
NOTE: The OPC-2014 nmea connector cable has 15
leads, numbered 1 to 15.
INSTALLATION AND CONNECTIONS
PIN No.
PIN No.
SPECIFICATIONS
—
1
GND
2
3
NMEA1 OUT (–) • Output level
: 5 V/40 mA max.
(RS-422 balanced type)
NMEA1 OUT (+)
4
NMEA1 IN (–)
5
NMEA1 IN (+)
6
ALERT1
11
ALERT2
7
NMEA2 OUT (–)
8
NMEA2 OUT (+)
9
NMEA2 IN (–)
10
NMEA2 IN (+)
12
NMEA3 OUT (–)
13
NMEA3 OUT (+)
14
NMEA3 IN (–)
15
NMEA3 IN (+)
• Input level
: Less than 2 mA
(at 2 V applied)
• Load rating
: DC 24 V/500 mA max.
Same as pins 2 and 3
Same as pins 4 and 5
Same as pins 2 and 3
Same as pins 4 and 5
SENTENCE FORMAT
—
7
DESCRIPTION
Connects to ground.
DSC, RMC, GGA, VTG, GSA, Connects to the NMEA input/output connector of
GSV, GBS, DTM, DSE, GNS, a transceiver to transmit an Individual DSC call,
GLL
or to connect to a GPS receiver. (p. 39)
The data communication speed (baud rate) can
RMC, GGA, VTG, GSA, GSV, be selected between 4800 bps (IEC61162-1) and
†
GBS , DTM, GNS, GLL
38400 bps (IEC61162-2) for each Input/Output
port. (Default: 4800 bps)
—
A short occurs between pins 6 and 11 when the alarm
buzzer sounds if a malfunction occurs, or an AIS
target is closer than your CPA and TCPA settings.
VDM, VDO, ALR, ACA, ACS, TXT, Connects to the Icom MarineCommander™ sysRMC*, GGA*, GNS*, GLL*, VTG*, tem or to a GPS receiver.
GSA*, GSV*, GBS*, DTM*
The data communication speed (baud rate) is
RMC, GGA, VTG, GSA, GSV, fixed to 38400 bps (IEC61162-2) for each Input/
Output port.
GBS†, DTM, GNS, GLL
RMC, GGA, VTG, GSA, GSV, Connects to a piece of navigation equipment or
GBS, DTM, GNS, GLL
to a GPS receiver.
The data communication speed (baud rate) can
RMC, GGA, VTG, GSA, GSV, be selected between 4800 bps (IEC61162-1) and
38400 bps (IEC61162-2) for each Input/Output
GBS†, DTM, GNS, GLL
port. (Default: 4800 bps)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
†When
a received GPS signal includes no GBS sentence, the transponder will not receive the signal from the external GPS receiver.
*Sent only when the “AIS+GPS” option is set in “AIS Output.” (p. 12)
37
7
INSTALLATION AND CONNECTIONS
■ Fuse replacement
■ About the VHF antenna
One fuse is installed in the DC power cable. If the fuse blows,
track down the source of the problem, have it repaired, and
replace the damaged fuse with a new one of the proper rating.
A key element in the performance of any communication system is the antenna. The VHF AIS/radio antennas should be
mounted in a location that has a clear, unobstructed view in
all directions and as far away from interference as possible,
for the best reception and transmission. When selecting a
mounting location, follow the guidelines below.
Fuse rating: 3 A
- Mount the VHF AIS/radio antennas at least 3 m (9.85 ft.)
away from each other.
- Mount the VHF AIS/radio antennas as high as possible.
- Be sure the location is out of the radar beam.
-B
e sure the location will not be shaded by a random antenna
or mast.
VHF AIS antenna
VHF radio antenna
At least 3 m (9.85 ft.)
38
INSTALLATION AND CONNECTIONS
7
■ Transceiver connection
• Antenna connector
The antenna uses a PL-259 connector.
30 mm
Coupling ring
10 mm (tin here)
10 mm tin
1–2 mm
solder solder
q Slide the coupling ring
down. Strip the cable jacket
and tin the shield.
Connect the transponder and a transceiver using the
OPC-2014 nmea connector cable. After connecting, an Individual DSC call can be made to the AIS target using the
transponder without entering the target’s MMSI code. (p. 22)
See the leaflet that comes with the transponder for details of
the transceivers which can operate with this function.
w Strip the cable as shown at
left. Tin the center conductor.
In this section, the connecting instructions of the IC-M504*1,
IC-M505*1, IC-M603*2 and IC-M604*2 are described as an
example. See the instruction manual of each for transceiver’s
connecting instructions.
e Slide the connector body
on and solder it.
*1 Requires the first two digits of the serial number to be “21” or
higher.
*2 Requires the first two digits of the serial number to be “31” or
higher.
rS
crew the coupling ring onto
the connector body.
30 mm (13⁄16 in) 10 mm (13⁄32 in) 1–2 mm (1⁄32–3⁄32 in)
☞ Continued on the next page.
OTE: There are many publications covering antennas
N
and their proper installation. Check with your local dealer
for more information and recommendations.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
39
7
INSTALLATION AND CONNECTIONS
■ Transceiver connection (Continued)
D IC-M603/M604
D IC-M504/M505
NMEA IN LEAD (Red)
GPS receiver/External speaker connector
NMEA OUT LEAD
(White)
Transceiver’s rear panel
• GPS receiver/External speaker connector
Transceiver’s rear panel
• NMEA IN LEAD (Red)
Outer conductor: NMEA IN (−)
Connects to lead 2 of OPC-2014.
Inner conductor: NMEA IN (+)
Connects to lead 3 of OPC-2014.
• NMEA OUT LEAD (White)
40
r NMEAOUT (+)
e NMEAOUT (–)
q NMEAIN (–)
q NMEA IN (−)
Connects to lead 2 of OPC-2014.
w NMEA IN (+)
Connects to lead 3 of OPC-2014.
Outer conductor: NMEA OUT (−)
Connects to lead 4 of OPC-2014.
e NMEA OUT (−)
Connects to lead 4 of OPC-2014.
Inner conductor: NMEA OUT (+)
Connects to lead 5 of OPC-2014.
r NMEA OUT (+)
Connects to lead 5 of OPC-2014.
SP (+)
SP (–)
w NMEAIN (+)
INSTALLATION AND CONNECTIONS
■ Mounting the transponder
D Using the mounting bracket
The universal mounting bracket supplied with your transponder allows overhead or dashboard mounting.
• OVERHEAD MOUNTING
qMount the bracket securely with the 4 supplied screws
(5 × 20 mm) to a surface which is more than 10 mm (13⁄32 in)
thick and can support more than 3 kg (6 lb 61 oz).
wAttach the transponder to the bracket so that the face of
the transponder is at 90° to your line of sight when operating it.
About the installation distance from the compass:
KEEP the transponder at least 1 m (3.3 ft) away from the
vessel’s magnetic navigation compass.
• MOUNTING ON THE BOARD
NOTE: Check the installation angle; the function display
may not be easy to read at some angles.
These bolts show a
mounting example only.
Not supplied with accessories.
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
41
7
INSTALLATION AND CONNECTIONS
■ MB-75 installation
An optional MB-75 flush mount kit is available for mounting the transponder to a flat surface, such as an instrument
panel.
Bolt
KEEP the transponder at least 1 m (3.3 ft) away from your
vessel’s magnetic navigation compass.
qUsing the template on the page 47, carefully cut a hole into
the instrument panel (or wherever you plan to mount the
transponder).
wSlide the transponder through the hole.
Clamp
r
r
tTighten the end bolts on the clamps (rotate clockwise) so
that the clamps press firmly against the inside of the instrument control panel.
yTighten the locking nuts (rotate counterclockwise) so that
the transponder is securely mounted in position.
y
eAttach the 2 supplied bolts (M5 × 8 mm) on either side of
the transponder.
rAttach the clamps on either side of the transponder.
42
• Make sure that the clamps align parallel to the transponder’s
body.
Locking nut
t
End bolt
uConnect the antenna, power cable, GPS receiver and
OPC-2014, then return the instrument control panel to its
original place.
MAINTENANCE
8
■ Troubleshooting
The following chart is designed to help you correct problems
which are not equipment malfunctions.
PROBLEM
If you are unable to locate the cause of a problem or solve
it through the use of this chart, contact your nearest Icom
Dealer or Service Center.
POSSIBLE CAUSE
The transponder does not • Bad connection at the power source.
turn ON.
Cannot transmit.
SOLUTION
REF.
• Check the connection to the transpon- p. 35
der.
• 1 minute has not passed from turning • Wait for 1 minute from turning ON the
ON the transponder power.
transponder power.
—
The plotter display does not • The results of the opening test is “NG” • Hold down [POWER•BRILL] for 1 sec- pp. 7,
appear.
(No Good).
ond to turn the power OFF, then push to 14
turn it ON again to reset the transponder.
—
• The transponder is still searching for • Wait until the transponder detects a
GPS satellite.
GPS satellites.
The GPS search display does • The GPS receiver is not connected to • Connect the GPS receiver to the tran- p. 35
not disappear.
the transponder.
sponder.
• Select the desired AIS target or display pp. 15,
An error beep sounds after • An AIS target is not selected.
16, 17
the detail screen of the AIS target.
pushing [DSC].
• A transceiver is not connected to the • Connect the transceiver to the transpon- p. 39
der.
transponder.
The collision alarm does not • The collision alarm function is OFF.
sound.
• The alarm buzzer function is OFF.
• Turn ON the collision alarm function.
• Turn ON the alarm buzzer function.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
p. 29
p. 33
43
8
MAINTENANCE
■ Error message
■ Diagnostics
Error message is displayed when a malfunction occurs that
has an error message programmed for it.
There are two types of diagnostic tests performed — Monitor
test, Transponder test and Version information.
Message contents
Description
GPS MALFUNCTION Appears when no GPS data is received.
NO GPS DATA
RX MALFUNCTION Appears when the transponder receive cirNO RCV
cuit has failed.
Appears when excessively strong atmoRX MALFUNCTION spheric noise, or noise signals from other
CH A NOISE LEVEL navigation equipment, are received on
Channel A.
Appears when excessively strong atmoRX MALFUNCTION spheric noise, or noise signals from other
CH B NOISE LEVEL navigation equipment, are received on
Channel B.
TX MALFUNCTION Appears when no RF power is output, or
NO TX POWER
the transmit circuit has failed.
Appears when the protective circuit cuts off
TX MALFUNCTION
the AIS signal after 1 second of continuous
CONTINUOUS TX
transmission.
ANT MALFUNCTION Appears when the antenna is open or
OPEN OR SHORT shorted.
Appears when the high VSWR* is detected
ANT MALFUNCTION
(the antenna is mismatched).
HIGH VSWR
*Voltage Standing Wave Ratio
44
• Monitor Test
You can check whether all LCD segments turn ON and OFF
properly.
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “Diagnostics,” then push [ENT].
ePush [∫] or [√] to select “Monitor Test,” then push [ENT].
rPush [∫] or [√] to select “All ON 2 Sec” or “All OFF 2 Sec,”
then push [ENT].
• All ON 2 Sec : All LCD segments turn ON for 2 seconds.
• All OFF 2 Sec: All LCD segments turn OFF for 2 seconds.
tPush [CLEAR] to return to the “DIAGNOSTICS” screen.
yPush [CLEAR] twice to exit the Menu mode.
[∫]
[ENT]
[√]
[CLEAR]
[MENU]
MAINTENANCE
• Transponder Test
You can check whether the transponder units work properly.
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “Diagnostics,” then push [ENT].
ePush [∫] or [√] to select “Transponder Test,” then push
[ENT].
rThe screen shows the results of the ROM, RAM, RX/TX
unit, antenna and GPS receiver tests; “OK” or “NG” (No
Good).
tPush [CLEAR] to return to the “DIAGNOSTICS” screen.
yPush [CLEAR] twice to exit the Menu mode.
[∫]
[ENT]
[√]
[CLEAR]
[MENU]
8
• Version Information
You can check the version information of SW (Software), FI
(Function Image) and the Internal GPS receiver.
qPush [MENU] to enter the Menu mode.
wPush [∫] or [√] to select “Diagnostics,” then push [ENT].
ePush [∫] or [√] to select “Version Information,” then push
[ENT].
rThe screen shows the version information of each item.
tPush [CLEAR] to return to the “DIAGNOSTICS” screen.
yPush [CLEAR] twice to exit the Menu mode.
[∫]
[ENT]
[√]
[CLEAR]
[MENU]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
45
9
SPECIFICATIONS AND OPTION
■ Specifications
145 (5 23⁄32)
91.4 (3 19⁄32)
108.4 (4 9⁄32)
110 (4 11⁄32)
: 161.975, 162.025 MHz (default)
156.025–162.025 MHz
• Type of emission
: 16K0GXW (GMSK)
• Current drain (at 12 V nominal) : TX: 1.5 A, RX: 0.7 A
• Power supply requirement
: 9.6 to 15.6 V DC
(negative ground)
• Operating temperature range : –20°C to +60°C; –4°F to +140°F
• Antenna impedance
: 50 ø nominal
• Intermediate frequency
AIS1
: 1st: 21.700 MHz, 2nd: 450 kHz
AIS2
: 1st: 30.875 MHz, 2nd: 450 kHz
• Dimensions
: 165(W) × 110(H) × 123(D) mm,
(Projections not included)
6 1⁄2(W) × 4 11⁄32(H) × 4 27⁄32(D) in
• Weight
: Approximately 1.0 kg; 2 lb 20 oz
• I/O connector
: High-density D-sub 15 pin
D Dimensions
• Frequency coverage
123 (4 27⁄32)
D General
D Transmitter
• Output power
:2W
• Modulation system
: GMSK
• Conducted Spurious emissions : Less than –36 dBm
D Receiver
• Sensitivity (20% Packet Error Rate): –110 dBm
• Intermodulation rejection ratio : More than 65 dB
• Spurious response rejection ratio : More than 74 dB (AIS)
More than 70 dB (DSC)
• Adjacent channel selectivity
: More than 70 dB
: Less than –57 dBm (AIS)
• Conducted spurious emission
This equipment meets IEC 62287-1 specifications.
46
165 (6 1⁄2)
31.4
(1 1⁄4)
77 (3 1⁄32)
Unit: mm (inch)
All stated specifications are subject to change without notice or obligation.
■ Option
•MB-75 flush mount kit
Used to mount the transponder to a panel.
TEMPLATE
10
165 (6 1⁄2)
146 (5 3⁄4)
Cut here
110 (4 11⁄32)
92.4 (3 5⁄8)
R12 (Max.)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Unit: mm (inch)
47
AtoN CODE AND DESCRIPTION
11
The following table shows all the AtoN codes which appear
on the detail screens of an “AtoN.” (p. 21)
Code
Description
Code
Description
0
DEFAULT, TYPE OF ATON NOT SPECIFIED
16
BEACON, PREFERRED CHANNEL STARBOARD HAND
1
REFERENCE POINT
17
BEACON, ISOLATED DANGER
2
RACON
18
BEACON, SAFE WATER
3
OFF SHORE STRUCTURE
19
BEACON, SPECIAL MARK
4
SPARE
20
CARDINAL MARK N
5
LIGHT, WITHOUT SECTORS
21
CARDINAL MARK E
6
LIGHT, WITH SECTORS
22
CARDINAL MARK S
7
LEADING LIGHT FRONT
23
CARDINAL MARK W
8
LEADING LIGHT REAR
24
PORT HAND MARK
9
BEACON, CARDINAL N
25
STARBOARD HAND MARK
10
BEACON, CARDINAL E
26
PREFERRED CHANNEL PORT HAND
11
BEACON, CARDINAL S
27
PREFERRED CHANNEL STARBOARD HAND
12
BEACON, CARDINAL W
28
ISOLATED DANGER
13
BEACON, PORT HAND
29
SAFE WATER
14
BEACON, STARBOARD HAND
30
SPECIAL MARK
15
BEACON, PREFERRED CHANNEL PORT HAND
31
LIGHT VESSEL / LANBY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
49
MEMO
MEMO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
< Intended Country of Use >
AT
FI
IT
PL
GB
RO
BE
FR
LV
PT
IS
TR
A-6860D-1EX-q
Printed in Japan
© 2011 Icom Inc.
Printed on recycled paper with soy ink.
CY
DE
LT
SK
LI
HR
CZ
GR
LU
SI
NO
DK
HU
MT
ES
CH
EE
IE
NL
SE
BG
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

advertisement

Key Features

  • Full dot-matrix display for real-time vessel traffic information
  • IPX7 waterproof protection for durability in harsh marine conditions
  • 3 lines of NMEA0183 Input/Output for seamless integration
  • Built-in GPS receiver for accurate positioning
  • Collision-risk management functions for enhanced safety
  • Integration with Icom VHF transceivers for convenient operation

Frequently Answers and Questions

What is the purpose of the MA-500TR?
The MA-500TR is a Class B AIS transponder that provides real-time vessel traffic information to enhance situational awareness and safety on the water.
What are the key features of the MA-500TR?
Key features include a full dot-matrix display, IPX7 waterproof protection, 3 lines of NMEA0183 Input/Output, built-in GPS receiver, collision-risk management functions, and integration with Icom VHF transceivers.
How does the MA-500TR help improve safety on the water?
The MA-500TR provides real-time vessel traffic information and collision-risk management functions, which help boaters identify and avoid potential hazards, enhancing overall safety on the water.
Is the MA-500TR easy to install and use?
Yes, the MA-500TR is designed for easy installation and operation. It comes with a mounting bracket and detailed instructions to guide you through the process.
Can I use the MA-500TR with my existing marine electronics?
Yes, the MA-500TR features 3 lines of NMEA0183 Input/Output, allowing it to seamlessly integrate with your existing marine electronics, such as VHF radios, chart plotters, and radar systems.

Related manuals

Download PDF

advertisement