Bathstore Freedom bath panel, acrylic bath panel bath panel, Freedom acrylic bath bath Installation instructions

Any Queries? Call : 08000 23 23 23
1
FREEDOM BATH PANELS
ST4 *20mm
ST4 *20mm
5x
10x
1x
ST4 *25mm
2x
2x
2x
2x
2
2a
Mark the drilling
hole position
with a pencil.
2b
5.0mm
45mm
Line 1
Line 1
2c
2d
ST4 *25mm
Line 1
+/- 0mm
Vertical to
Floor
45mm
Line 1
4
180mm
To fix bath panel to the floor, use silicone.
Not only does this fix this panel in place, but it also seals the
underneath of the bath from splash water.
45mm
45mm
180mm
3
© ASAQ
1-1
A
UNIVERSAL LEG SET - INSTALLATION INSTRUCTIONS
41405000375
2x
6x
1
ST5 *16mm
2
●
4x
6x
3
Suggest 542mm for Freedom
bath.
ST5 *16mm
●
●
545mm
NOTES
Assemble the bath on
a mat to protect the bath
surface from damage or
scratching
These installation instructions
do not include the waste, tap
or any other items. Such
items should be installed by
a suitably qualified person.
●
Follow each step in turn.
●
Fit horizontal batten before
securing bath to the floor
(see page 3)
4
5
● It
is essential that once the bath is in its final position the bath
legs be firmly fixed to and secured to the floor using fixings
appropriate for the type of floor surface ( such fixing not included )
7
Any Queries? Call : 08000 23 23 23
6
1-3
8
J
Bathstore acrylic bath panel installation instructions
(not suitable for Freedom baths)
FRONT PANEL
●
Secure the metal clamps to the wooden
blocks underneath the bath rim.
●
Place bath in final position.
●
Mark the outline of the bath on the floor.
1x
ST4 *20mm
ST4 *20mm
8x
4x
1
3
ST4 *25mm
2x
2x
ST4 *16mm
2x
1
2x
2
●
END PANEL
Fix the plastic floor L brackets to the floor
spaced as shown in the diagram.
Dimensions in millimetres.
1x
5.0mm
Line 1
●
3
Clip the panel into place ensuring it is
firmly held in position by the top metal
clamps, and the floor L brackets prevent
the panel being ‘kicked’ in.
b
ST4 *20mm
4x
2x
c
ST4 *25mm
2x
2x
d
a
Line 1
2x
2x
Any Queries? Call : 08000 23 23 23
ST4 *25mm
5
4
2-3
6
J
Recommended method for installation of Acrylic baths
(for Freedom baths refer to the instructions supplied with the bath)
●
Place the bath in position to determine height, water and soil requirements.
1
3
2
> 40mm
●
Screw a batten of 2” by 1” treated timber to the wall
horizontally to support the bath rim. This ensures that
the bath will remain stable and the rim cannot flex.
●
Place the bath back into position. Attach all water
and waste connections.
4
●
Screw another 2” by 1” treated timber batten
vertically onto the wall, clamping the bath to the
wall. This batten should be at least 40mm in from
the corner of the bath. This batten will provide
additional rim support. This should be done on both
corners to securely hold the bath in place.
‘Acrylic baths will flex when filled with water, so it is
important that your bath is installed to allow for some
movement.
●
The weight of the bath should be taken by the feet
and not battens. Battens are a good way of
supporting the rim of a bath, but can cause stress
points. They should not be physically attached to the
blocks underneath the bath, and ideally there should
be a small gap between the blocks and battens.’
When installing the bath panels, remember to install
the floor fixed L brackets so as to prevent the bottom of
the panel being ‘kicked’ in. See section 4, 5 and 6 on
previous page.
Any Queries? Call : 08000 23 23 23
3-3
J