Advantech AIMB-562 KIOSK User manual

User Manual

AIMB-562 KIOSK

Intel

®

LGA775 Core™ 2 Duo mATX Motherboard with Dual

VGA/LVDS/DDR2/10 COM/LAN

Copyright

The documentation and the software included with this product are copyrighted 2009 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co.,

Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.

Acknowledgements

AWARD is a trademark of Phoenix Technologies Ltd.

IBM and PC are trademarks of International Business Machines Corporation.

Intel

®

Pentium

®

M/Celeron

®

M are trademarks of Intel Corporation.

WinBond is a trademark of Winbond Corporation.

All other product names or trademarks are properties of their respective owners.

AIMB-562 KIOSK User Manual

Part No. 2002056212

Printed in Taiwan ii

Edition 3

September 2009

A Message to the Customer

Advantech Customer Services

Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech equipment is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.

Your satisfaction is our primary concern. Here is a guide to Advantech’s customer services. To ensure you get the full benefit of our services, please follow the instructions below carefully.

Technical Support

We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone.

So please consult this manual first. If you still cannot find the answer, gather all the information or questions that apply to your problem, and with the product close at hand, call your dealer. Our dealers are well trained and ready to give you the support you need to get the most from your Advantech products. In fact, most problems reported are minor and are able to be easily solved over the phone.

In addition, free technical support is available from Advantech engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products.

iii AIMB-562 KIOSK User Manual

Declaration of Conformity

FCC

This device complies with the requirements in part 15 of the FCC rules:

Operation is subject to the following two conditions:

This device may not cause harmful interference

This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. The user is advised that any equipment changes or modifications not expressly approved by the party responsible for compliance would void the compliance to FCC regulations and therefore, the user's authority to operate the equipment.

Caution! There is a danger of a new battery exploding if it is incorrectly installed.

Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.

AIMB-562 KIOSK User Manual iv

CPU Compatibility

CPU family sSpec Core stepping

Power FSB Mgn tech L2 cache

SLB9Y M0 65W 1066 45nm 3MB Core2 Duo E7400

2.80GHz EM64T

Dual Core

Core2 Duo E6700

2.66GHz EM64T

Dual Core

Core2 Duo E6600

2.40GHz EM64T

Dual Core

Core2 Duo E6400

2.13GHz EM64T

Dual Core

SL9S7 B2

SL9S8 B2

SL9S9 B2

Core2 Duo E6300

1.86GHz EM64T

Dual Core

SL9SA B2

Core2 Duo E5300

2.6GHz EM64T Dual

Core

SLB9U R0

Core2 Duo E4300

1.8GHz EM64T Dual

Core

SL9TB L2

Pentium Dual-Core

1.8GHz E2160

SLA8Z M0

Pentium-D 830

3.00GHz EM64T

Dual Core

Pentium-4 670

3.80GHz EM64T

SL8CN A0

SL7Z3 N0

65W

65W

65W

65W

65W

65W

65W

130W

115W

1066 65nm

1066 65nm

1066 65nm

1066 65nm

800

800

800

800

800

45nm

65nm

65nm

90nm

90nm

4MB

4MB

2MB

2MB

2MB

2MB

1MB

2MB

Celeron D E1200

1.6GHz EM64T

Celeron-D 352

3.20GHz EM64T

SLAQ

W

M0

SL96P C1

Celeron 440 2GHz SL9XL A1

Celeron 430 1.8GHz SL9XN A1

65w

86W

35W

35W

800

533

800

800

65nm

65nm

65nm

65nm

Advantech

PN

96MP2DD-

28FA-3M7T

96MP2DD-

26FA-4M7T

96MP2DD-

24FA-4M7T

96MP2DD-

21FA-2M7T

96MP2DD-

18FA-2M7T

96MPPD-

2.6F8-

2M7T1

96MP2DD-

18F8-2M7T

96MPPD-

1.8F8-1M7T

96MPPD-

3.0F8-2M7T

2MB 96MPP4-

3.8F8-

2M7T1

512KB 96MPC2-

1.6F8-5K7T

512KB 96MPCD-

3.2F5-5K7T

512KB 96MPC4-

2.0F8-5K7T

512KB 96MPC4-

1.8F8-5K7T v AIMB-562 KIOSK User Manual

Memory Compatibility

Brand Size Speed Type ECC

Vendor

PN

Advantech

PN

Memory

Apacer 1 GB

DDR2

533

Transcend

256

MB

DDR2

533

512

MB

DDR2

533

DSL

1 GB

DDR2

533

DDR2 N 78.01066.4

00

NA

SAMSUNG K4T51083QB-

ZKD5 (128x4)

DDR2 N

TS32MLQ6

4V5F

NA

SAMSUNG 443 K4T56083QF-

GCD5 (32x8)

DDR2 N NA NA

DDR2 N NA NA infineon HYB18T512 800AF37

FSS43331 (64x8)

ELPIDA E5108AE-5C-E (64x8)

Apacer

(RoHS)

Transcend

(RoHS)

Transcend

(RoHS)

512

MB

DDR2

533

1 GB

DDR2

512

MB

256

MB

512

MB

512

MB

1 GB

1 GB

2 GB

2 GB

1 GB

2 GB

533

DDR2

667

1 GB

DDR2

667

2 GB

DDR2

667

DDR2

533

DDR2

533

DDR2

667

DDR2

667

DDR2

667

DDR2

667

DDR2

667

DDR2

800

DDR2

667

DDR2 N

DDR2 N

DDR2 N

DDR2 N

78.91G66.

420

78.01G66.

420

96D2-

512M533NN

-AP

ELPIDA E5108AG-5C-E

(64x8)

96D2-

1G533NN-

AP

ELPIDA E5108AGBG-6E-E

(64x8)

DDR2 N

DDR2 N

DDR2 N

78.91G92.

420

78.01G92.

420

NA

ELPIDA E5108AG-6E-E

(64x8)

NA


(64x8)

78.A1G9O.

404

96D2-

2G667-AP

SEC K4T1G08400 (128x8)

TS32MLQ6

4V5M

96D2-

256M533NN

-TR infineon HYB18T512160AF3.7

3VV21710 (32x16)

TS64MLQ6

4V5J

96D2-

512M533NN

-TR1

SEC K4T51083QC ZCD5

(64X8)

DDR2 N

TS6QNJ22

850-6S/

TS64MLQ6

4V6J

96D2-

512M667NN

-TR

SAMSUNG K4T51083QC

ZCE6 (64x8)

DDR2 N

DDR2 N

TS2QNJ23

450-6S

96D2-

1G667NN-

TR

TS2QNJ23

450-6S/

TS128MLQ

64V6J

96D2-

1G667NN-

TR

SEC K4T51083QE ZCE6

(64x8)

SEC K4T51083QG HCE6

(64x8)

DDR2 N

SAMSUNG K4T1G084QD-

ZCE6 (128x8)

DDR2

DDR2

DDR2

N

N

N

TS5QNU23

451-6S

96D2-

2G667-TR

TS256MLQ

64V6U

NA

TS128MLQ

64V8J

NA

TS256MLQ

64V6U

NA

Micron 7HE12 D9HNL (128x8)

ProMOS V59C1512804QBF25

(64x8)

SAMSUNG K4T1G084QA-

ZCE6 (128x8)

AIMB-562 KIOSK User Manual vi

1 GB

DDR2

667

DSL

2 GB

DDR2

667

1 GB

DDR2

800

2 GB

DDR2

800

Kingston

(RoHS)

2 GB

DDR2

667

1GB

DDR2

800

DDR2 N

DDR2 N

DDR2 N

DDR2 N

DDR2 N

DDR2 N

NA

NA

NA

NA

NA NA

NA NA

KVR667D2

N5/2G

NA

KVR800D2

N5/1G

NA

Ordering Information


(64x8)

ELPIDA E1108ACSE-6E-

E(128x8)

ELPIDA E5108AHSE-8E-E

(64x8)

ELPIDA E1108ACBG-8E-E

(128x8)

Micron 7KE12 D9HNL (128x8)

ELPIDA E5108AHSE-8E-E

(64x8)

AIMB-562 KIOSK Ordering Information

Part Number On-board

Processor

AIMB-562VG-KSA1E NA

AIMB-562VG-GRA1E

AIMB-562L-KSA1E

NA

NA

Chipset Memory LAN

945G

945G

DDR2 533/

667

1

DDR2 533/

667

1

945GC DDR2 533/

667

1

COM

10

10

10

Display

CRT/CRT/

LVDS

CRT/CRT

CRT

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase.

This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1.

Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs.

2.

Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.

3.

If your product is diagnosed as defective, obtain an RMA (return merchandise authorization) number from your dealer. This allows us to process your return more quickly.

4.

Carefully pack the defective product, a fully-completed Repair and Replacement

Order Card and a photocopy proof of purchase date (such as your sales receipt) vii AIMB-562 KIOSK User Manual

in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service.

5.

Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.

Initial Inspection

Before you begin installing your motherboard, please make sure that the following materials have been shipped:

LGA 775 Core

TM

2 Duo/Pentium 4/Pentium dual-core/Celeron® D Processorbased Micro ATX with DDR2/PCIe/Single GbE LAN

1 x AIMB-562 KIOSK startup manual

1 x CD with driver utility and manual

2 x Serial ATA HDD data cable

2 x Serial ATA HDD power cable

4 x Com port cable kit

1 x I/O port bracket

1 x jumper package

1 x warranty card

If any of these items are missing or damaged, contact your distributor or sales representative immediately. We have carefully inspected the AIMB-562 KIOSK mechanically and electrically before shipment. It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the AIMB-562 KIOSK, check it for signs of shipping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or your local sales representative immediately. Also notify the carrier. Retain the shipping carton and packing material for inspection by the carrier. After inspection, we will make arrangements to repair or replace the unit.

AIMB-562 KIOSK User Manual viii

Contents

Chapter 1

General Information

............................1

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

1.10

1.11

1.12

Introduction ............................................................................................... 2

Features .................................................................................................... 2

Specifications ............................................................................................ 3

1.3.1

System .......................................................................................... 3

1.3.2

Memory ......................................................................................... 3

1.3.3

Input/Output .................................................................................. 3

1.3.4

Graphics........................................................................................ 3

1.3.5

Ethernet LAN ................................................................................ 3

1.3.6

Industrial features ......................................................................... 3

1.3.7

Mechanical and environmental specifications............................... 3

Jumpers and Connectors .......................................................................... 4

Table 1.1: Jumpers...................................................................... 4

Table 1.2: Connectors ................................................................. 4

Board layout: Jumper and Connector Locations ....................................... 5

Figure 1.1 Jumper and Connector Location ................................ 5

Figure 1.2 I/O Connectors ........................................................... 6

AIMB-562 KIOSK Block Diagram .............................................................. 6

Figure 1.3 AIMB-562 KIOSK Block Diagram ............................... 6

Safety Precautions .................................................................................... 7

Jumper Settings ........................................................................................ 8

1.8.1

How to set jumpers ....................................................................... 8

1.8.2

CMOS clear (CMOS1) .................................................................. 8

Table 1.3: CMOS1....................................................................... 8

1.8.3

Volumn adjustment(VOLADJ1)..................................................... 8

Table 1.4: VOLADJ1.................................................................... 8

1.8.4

Chassis instruction connector (JCASE1) ...................................... 9

1.8.5

ATX/AT mode selector (PSON1) .................................................. 9

Table 1.5: ATX/AT mode selector (PSON1)................................ 9

1.8.6

AT switch connector(AT_SWITCH1) ............................................ 9

1.8.7

COM3/7 RS 232/422/485 mode selector (JSETCOM3456/78910)

...................................................................................................... 9

Table 1.6: COM3456/78910 RS 232/422/485 mode selector

(JSETCOM3456/78910) ............................................. 9

1.8.8

LVDS power jumper connector(JLVDSPWR1) ........................... 10

Table 1.7: LVDS power jumper selectior ................................... 10

System Memory ...................................................................................... 10

Memory Installation Procedures.............................................................. 10

Cache Memory........................................................................................ 10

Processor Installation.............................................................................. 10

Chapter 2

Connecting Peripherals

....................11

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

Introduction ............................................................................................. 12

Parallel Port (LPT1)................................................................................. 12

USB Ports (USB12/LAN2_USB34/USB56/USB78) ................................ 13

Table 2.1: LAN LED Indicator.................................................... 13

VGA Connector (VGA1/VGA2) ............................................................... 14

Serial Ports (COM1~COM10) ................................................................. 15

PS/2 Keyboard and Mouse Connector (KBMS1) .................................... 16

CPU Fan Connector (CPU_FAN1).......................................................... 17

System FAN Connector (SYS_FAN1)..................................................... 18

Front Panel Connectors (JFP1) .............................................................. 19

2.9.1

Power/Sleep Waiting LED (JFP1)............................................... 19

ix AIMB-562 KIOSK User Manual

2.10

2.11

2.12

2.13

2.14

2.15

2.16

2.17

2.18

2.19

2.20

2.21

2.22

Table 2.2: ATX power supply LED status (No support for AT power) ............................................................................. 19

2.9.2

Reset Connector (JFP1 pins 5 & 7) ............................................ 20

2.9.3

HDD LED Connector (JFP1 pins 1 & 3)...................................... 20

2.9.4

ATX Soft Power Switch (JFP1 pins 6 & 8).................................. 20

Line In, Line Out, Mic In Connector (AUDIO1)........................................ 20

Serial ATA Interface (SATA1, SATA2).................................................... 21

ATX Power Connector (ATX12V1, EATXPWR1).................................... 22

SPI Flash Connector (SPI_CN1) ............................................................ 23

Front Panel Audio Connector (FPAUDIO1) ............................................ 24

System FAN Connector (SYS_FAN2) .................................................... 25

Primary EIDE Connector (IDE1) ............................................................. 25

USB 2.0 Connector (USB 56, 78) ........................................................... 26

LVDS Connector (JLVDS1) .................................................................... 27

LVDS Backlight Enabler (JBL1) .............................................................. 27

LVDS Power Jumper Selection1 (JLVDSPWR1).................................... 28

Volume Adjustment Connector (VOLADJ1)............................................ 28

GPIO Pin Header (GPIO1, GPIO2)......................................................... 29

Chapter 3 BIOS Operation

................................. 31

3.1

3.2

Introduction ............................................................................................. 32

BIOS Setup ............................................................................................. 32

3.2.1

Main Menu .................................................................................. 33

3.2.2

Standard CMOS Features .......................................................... 34

3.2.3

Advanced BIOS Features ........................................................... 35

3.2.4

Advanced Chipset Features ....................................................... 36

3.2.5

Integrated Peripherals ................................................................ 38

3.2.6

Security Chip Configuration ........................................................ 40

3.2.7

TPM Support............................................................................... 40

3.2.8

Power Management Setup ......................................................... 41

3.2.9

PnP/PCI Configurations.............................................................. 43

3.2.10 PC Health Status ........................................................................ 44

3.2.11 Load Setup Defaults ................................................................... 45

3.2.12 Set Password.............................................................................. 45

3.2.13 Save & Exit Setup....................................................................... 47

3.2.14 Quit without Saving..................................................................... 47

Chapter 4 Chipset Software Installation Utility

49

4.1

4.2

4.3

Before you begin..................................................................................... 50

Introduction ............................................................................................. 50

Windows XP Driver Setup....................................................................... 51

Chapter 5 VGA Setup

......................................... 53

5.1

5.2

Introduction ............................................................................................. 54

Windows Vista/XP/2000.......................................................................... 54

Chapter 6 LAN Configuration

............................ 57

6.1

6.2

6.3

6.4

Introduction ............................................................................................. 58

Features.................................................................................................. 58

Installation............................................................................................... 58

Win XP/Vista Driver Setup (Realtek RTL8111C) .................................... 58

AIMB-562 KIOSK User Manual x

Appendix A

Programming the Watchdog Timer

..61

A.1

Programming the Watchdog Timer ......................................................... 62

A.1.1

Watchdog timer overview............................................................ 62

A.1.2

Programming the Watchdog Timer ............................................. 62

Table A.1: Watchdog Timer Registers ....................................... 64

A.1.3

Example Program ....................................................................... 65

Appendix B

I/O Pin Assignments

..........................69

B.1

B.2

B.3

B.4

B.5

B.6

B.7

B.8

B.9

B.10

B.11

B.12

B.13

B.14

B.15

B.16

B.17

B.18

B.19

B.20

Parallel Port (LPT1)................................................................................. 70

Table B.1: Parallel Port (LPT1) .................................................. 70

USB Header (USB56) ............................................................................. 70

Table B.2: USB Header (USB56)............................................... 70

USB Header (USB78) ............................................................................. 71

Table B.3: USB Header (USB78)............................................... 71

VGA Connector (VGA1) .......................................................................... 71

Table B.4: VGA Connector (VGA1) ........................................... 71

VGA Connector (VGA2) .......................................................................... 72

Table B.5: VGA Connector (VGA2) ........................................... 72

RS-232 Interface (COM1-COM2)............................................................ 72

Table B.6: RS-232 Interface (COM1~COM2) ............................ 72

RS-232/422/485 Setting Interface (JETCOM3456~78910)..................... 73

Table B.7: RS-232/422/485 Setting Interface

(JETCOM3456~78910) ............................................ 73

RS-232 Interface (COM3456) ................................................................. 73

Table B.8: RS-232 Interface(3456) ............................................ 73

RS-232 Interface (COM78910) ............................................................... 74

Table B.9: RS-232 Interface (COM78910)................................. 74

SPI_CN1: SPI fresh card pin connector.................................................. 75

Table B.10:SPI_CN1:SPI fresh card pin connector .................... 75

PS/2 Keyboard and Mouse Connector (KBMS1) .................................... 75

Table B.11:PS/2 Keyboard and Mouse Connector (KBMS1) ..... 75

CPU Fan Power Connector (CPU_FAN1) .............................................. 76

Table B.12:CPU Fan Power Connector (CPU_FAN1)................ 76

System Fan Power Connector (SYS_FAN1/SYS_FAN2) ....................... 76

Table B.13:System Fan Power Connector (SYSFAN1/SYSFAN2)

.................................................................................. 76

Front Panel Connectors (JFP1) .............................................................. 76

B.14.1 Power/Sleep LED (JFP1)............................................................ 77

Table B.14:Power/Sleep LED (JFP1) ......................................... 77

B.14.2 Reset Connector (JFP1) ............................................................. 77

Table B.15:Reset Connector (JFP1)........................................... 77

B.14.3 HDD LED Connector (JFP1)....................................................... 77

Table B.16:HDD LED Connector (JFP1) .................................... 77

B.14.4 ATX Soft Power Switch (JFP1) ................................................... 77

Table B.17:ATX Soft Power Switch (JFP1)................................. 77

ATX1 12 V Auxiliary Power Connector (ATX12V1)................................. 78

Table B.18:ATX1 12 V Auxiliary Power Connector (ATX12V1) .. 78

ATX Power Connector (EATXPWR1) ..................................................... 78

Table B.19:ATX Power Connector (ATX2) ................................. 78

USB/LAN ports (LAN2_USB12/USB34).................................................. 79

Table B.20:USB Port................................................................... 79

Table B.21:Ethernet 10/100Base-T RJ-45 Port .......................... 79

Line Out, Mic In Connector (AUDIO1)..................................................... 79

Serial ATA0 (SATA1) .............................................................................. 79

Table B.22:Serial ATA0 (SATA1)................................................ 79

Serial ATA1 (SATA2) .............................................................................. 80

Table B.23:Serial ATA1 (SATA2)................................................ 80

xi AIMB-562 KIOSK User Manual

B.27

B.28

B.29

B.30

B.31

B.32

B.21

B.22

B.23

B.24

B.25

B.26

AT/ATX Mode (PSON1).......................................................................... 80

Table B.24:AT/ATX Mode (PSON1) ........................................... 80

JLVDS1: LVDS connector....................................................................... 80

Table B.25:LVDS Connector (JLVDS1)...................................... 80

JBL1(LVDS inverter connector) .............................................................. 81

Table B.26:LCD Inverter Power Connector (JBL1)..................... 81

JLVDSPWR1(LVDS power jumper selection)......................................... 81

Table B.27:LVDS power jumper selection (JLVDSPWR1) ......... 81

FPAUDIO1(Front Panel Audio Connector) ............................................. 81

Table B.28:Front Panel Audio Connector (FPAUDIO1).............. 81

GPIO12(GPIO pin header)...................................................................... 82

Table B.29:GPIO pin header(GPIO1) ......................................... 82

Table B.30:GPIO pin header(GPIO2) ......................................... 82

VOLADJ1(Volumn Adjustment connector).............................................. 82

Table B.31:Volumn Adjustment connector (VOLADJ1) .............. 82

System I/O Ports..................................................................................... 82

Table B.32:System I/O Ports ...................................................... 82

JCASE1(Open Case Connector) ............................................................ 83

Table B.33:Case Open Connector(JCASE1).............................. 83

DMA Channel Assignments .................................................................... 83

Table B.34:DMA Channel Assignments ..................................... 83

Interrupt Assignments ............................................................................. 84

Table B.35:Interrupt Assignments .............................................. 84

1st MB Memory Map............................................................................... 84

Table B.36:1st MB Memory Map ................................................ 84

AIMB-562 KIOSK User Manual xii

Chapter

1

General Information

1

1.1

Introduction

The AIMB-562 KIOSK is designed with the Intel

®

945G/945GC and the ICH7 for industrial applications that require both performance computing and enhanced power management capabilities. The motherboard supports Intel Pentium LGA 775 Core

TM

2 Duo up to 2.8 GHz / Pentium dual-core up to 2.2 Ghz / Pentium 4 up to 3.4 GHz/

Celeron

®

D up to 2.0 Ghz with

533/800/1066

MHz front side bus and DDR2 533/667

MHz up to 2 GB.

The AIMB-562 KIOSK offers cost-saving integrated graphics, built on the Intel

®

945G/945GC chipset and features the unique Intel

®

Extreme Graphics architecture that maximizes VGA performance and shares system memory up to 224 MB.

Advantech AIMB-562 KIOSK is designed with an Intel 945G/945GC chipset and supports Intel Core 2 Duo processor up to FSB 1066 MHz. A rich I/O connectivity of 10 serial ports, 8 USB 2.0, single GbE LAN and 2 SATA ports.

1.2

Features

Cost effective 945G/945GC chipset: support 533/800/1066 Front side bus

Rich I/O connectivity: 10 serial ports, 8 USB 2.0, single GbE LAN

Standard Micro ATX form factor with industrial feature: The AIMB-562

KIOSK is the most fully-featured Micro ATX motherboard with balanced expandability and the performance

Wide selection of storage devices: SATA HDD, customers benefit the flexibility of using the most suitable storage device for large capacity

Optimized integrated graphic solution: With Intel

®

Graphics Media Accelerator 950, it supports versatile display options and 32-bit 3D graphics engine.

AIMB-562 KIOSK User Manual 2

1.3

Specifications

1.3.1

System

CPU: LGA 775 Core

TM

2 Duo up to 2.8 Ghz / Pentium dual-core up to 2.2 Ghz /

Pentium 4 up to 3.4 Ghz / Celeron

®

D up to 2.0 Ghz

BIOS: Award SPI 16 Mbit BIOS

System chipset: Intel 945G/945GC with ICH7

SATA hard disk drive interface: Two on-board SATA connectors with data transmission rate up to 300 MB

1.3.2

Memory

RAM: Up to 4 GB in 2 slots 240-pin SODIMM sockets. Supports dual channel

DDRII 533/667 SDRAM

1.3.3

Input/Output

PCIe bus: 1PCIe x 4 slot

Enhanced parallel port: Configured to LPT1 with 25 pin box header. Supports

EPP/SPP/ECP

Serial ports: Ten serial ports, two of RS-232/422/485 and eight of RS-232 serial ports

Keyboard and PS/2 mouse connector: Two 6-pin mini-DIN connectors are located on the mounting bracket for easy connection to a PS/2 keyboard and mouse

USB port: Supports up to eight USB 2.0 ports with transmission rate up to 480

Mbps, 4 on board pin header and 4 external ports)

1.3.4

Graphics

Controller: Chipset integrated VGA controller

Display memory: Dynamically shared system memory up to 224 MB

CRT: Up to 2048 x 1536 resolution, 400 MHz RAMDAC

1.3.5

Ethernet LAN

Supporting single/dual 10/100/1000Base-T Ethernet port (s) via PCI Express x1 bus which provides 500 MB/s data transmission rate

Controller: LAN: Realtek RTL8111C

1.3.6

Industrial features

Watchdog timer: Can generate a system reset. The watchdog timer is programmable, with each unit equal to one second or one minute (255 levels)

1.3.7

Mechanical and environmental specifications

Operating temperature: 0 ~ 60° C (32 ~ 140° F, Depending on CPU)

Storage temperature: -20 ~ 70° C (-4 ~ 158° F)

Humidity: 5 ~ 95% non-condensing

Power supply voltage: +3.3 V, +5 V, +12 V, -12 V, 5 Vsb

3 AIMB-562 KIOSK User Manual

Power consumption:

+5 V @ 4 A, +3.3 V @ 1.02 A, +12 V @ 2.35 A, 5 VSB @ 0.26 A, -12 V @ 0.12

A Measure the maximum current value which system under maximum load

(CPU: Top speed, RAM & Graphic: Full loading)

Board size: 244 mm x 244 mm (9.6" x 9.6")

Board weight: 0.75 kg

1.4

Jumpers and Connectors

Connectors on the AIMB-562 KIOSK motherboard link it to external devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers used to configure your system for your application.

The tables below list the function of each of the board jumpers and connectors. Later sections in this chapter give instructions on setting jumpers. Chapter 2 gives instructions for connecting external devices to your motherboard.

Table 1.1: Jumpers

Label Function

CMOS1

JCASE1

PSON1

JSETCOM3456

JSETCOM78910

JLVDSPWR1

VOLADJ1

CMOS clear

Chassis Instruction Connector

AT/ATX mode selector

Serial port:RS232/RS422/RS485 jumper setting

Serial port:RS232/RS422/RS485 jumper setting

LVDS Power Jumpr Selection

Volumn adjustment connector

Table 1.2: Connectors

Label Function

JFP1

LPT1

USB56

USB78

VGA1

VGA2

COM1/COM2

COM3~6/COM7~10

KBMS1

CPU_FAN1

SYS_FAN1

USB12

LAN2_USB34

SATA1

SATA2

Reset connector

HDD LED connector

ATX soft power switch (PS_ON)

Power/Sleep waiting LED

Parallel port

USB port 5, 6 (on board)

USB port 7 8(on board)

VGA connector

2nd VGA connector

Serial port: COM1/COM2 (9-pin connector)

Serial port: COM3~-6/COM7~10 (40-pin connector)

PS/2 keyboard and Mouse connector

Cable length: 20 meter

CPU FAN connector

System FAN connector 1

USB port 1,2

LAN2/USB port 3,4

Serial ATA0

Serial ATA1


Table 1.2: Connectors

ATX12V1

EATXPWR1

SPI_CN1

AUDIO1

FPAUDIO1

GPIO1

GPIO2

JLVDS1

JLVDSPWR1

JBL1

SYS_FAN2

VOLADJ1

AT_SWITCH1

ATX 12 V Auxiliary power connector

ATX power connector

SPI flash card pin header

Line Out, Mic IN connector

Front Panel audio connector (FP_AUDIO)

GPIO pin header (SMD pitch=2.0 mm) 2 x 4

GPIO pin header (SMD pitch=2.0 mm) 2 x 4

LVDS connector

LVDS power jumper selection1-2:3.3 V 2-3:5 V

LVDS inverter connector

System Fan connector 2

Volume adjustment connector

AT Switch power connector

1.5

Board layout: Jumper and Connector Locations

Figure 1.1 Jumper and Connector Location


Figure 1.2 I/O Connectors

1.6

AIMB-562 KIOSK Block Diagram

Intel 945G/945GC

GMCH

Figure 1.3 AIMB-562 KIOSK Block Diagram


1.7

Safety Precautions

Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis.

Caution! Always ground yourself to remove any static charge before touching the motherboard. Modern electronic devices are very sensitive to electrostatic discharges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components on a static-dissipative surface or in a static-shielded bag when they are not in the chassis.

Caution! The computer is provided with a battery-powered Real-time Clock circuit. There is a danger of explosion if battery is incorrectly replaced.

Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to manufacturer's instructions.

Caution! There is a danger of a new battery exploding if it is incorrectly installed.

Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.


1.8

Jumper Settings

This section provides instructions on how to configure your motherboard by setting the jumpers. It also includes the motherboards's default settings and your options for each jumper.

1.8.1

How to set jumpers

You can configure your motherboard to match the needs of your application by setting the jumpers. A jumper is a metal bridge that closes an electrical circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” (or turn ON) a jumper, you connect the pins with the clip. To “open” (or turn OFF) a jumper, you remove the clip. Sometimes a jumper consists of a set of three pins, labeled 1, 2, and 3. In this case you connect either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when setting jumpers.

1.8.2

CMOS clear (CMOS1)

The AIMB-562 KIOSK motherboard contains a jumper that can erase CMOS data and reset the system BIOS information. Normally this jumper should be set with pins

1-2 closed. If you want to reset the CMOS data, set J1 to 2-3 closed for just a few seconds, and then move the jumper back to 1-2 closed. This procedure will reset the

CMOS to its default setting.

Table 1.3: CMOS1

Function Jumper Setting

1

*Keep CMOS data

1-2 closed

1

Clear CMOS data

2-3 closed

*default setting

1.8.3

Volumn adjustment(VOLADJ1)

Table 1.4: VOLADJ1


* aduio from LINE_OUT 1-2 closed, 4-5 closed

1 2 3 4 5

Caution! The volume output from LINE_OUT has been amplified so please be cautious when use earphone. Jumper 1-2 & 4-5 can be removed if user need sound from LINE_OUT with a tuner.


1.8.4

Chassis instruction connector (JCASE1)

The AIMB-562 KIOSK motherboard contains a jumper that offer a chassis open sensor. The buzzer on the motherboad beeps when the case is opened.

1.8.5

ATX/AT mode selector (PSON1)

Table 1.5: ATX/AT mode selector (PSON1)


AT mode

*ATX mode

*default setting

1-2 closed

2-3 closed

1.8.6

AT switch connector(AT_SWITCH1)

The AT switch connector for AIMB-562 KIOSK is default with 1-2 pin closed for only customer who use AT switch power supply.

1.8.7

COM3/7 RS 232/422/485 mode selector (JSETCOM3456/78910)

Users can use JSETCOM3456/78910 to select among RS 232/422/485 modes for

COM3 and COM7. The default setting is RS 232.

RS232 RS422 RS485

Table 1.6: COM3456/78910 RS 232/422/485 mode selector

(JSETCOM3456/78910)

Function

*RS232

RS422

RS-485

*: Default

Jumper Setting

(5-6) + (7-9) + (8-10) + (13-15) + (14-16) closed

(3-4) + (9-11) + (10-12) + (15-17) + (16-18) closed

(1-2) + (9-11) + (10-12) + (15-17) + (16-18) closed


1.8.8

LVDS power jumper connector(JLVDSPWR1)

JLVDSPWR1 is the jumper for either 3.3 V or 5 V output when connector to LCD panel.

Table 1.7: LVDS power jumper selectior

Function

connect to 3.3 V connect to 5 V

Jumper Setting

1-2 pin closed

2-3 pin closed

1.9

System Memory

The AIMB-562 KIOSK has two sockets for 240-pin SODIMMx2.

All these sockets use 1.8 V unbuffered double data rate synchronous DRAMs (DDR2

SDRAM). They are available in capacities of 512 and 1024 MB. The sockets can be filled in any combination with DIMMs of any size, giving a total memory size between

512 MB and 2 GB. AIMB-562 KIOSK does NOT support ECC (error checking and correction).

1.10

Memory Installation Procedures

To install SODIMMs, first make sure the two handles of the SODIMM socket are in the “open” position. i.e. The handles lean outward. Slowly slide the SODIMM module along the plastic guides on both ends of the socket. Then press the SODIMM module right down into the socket, until you hear a click. This is when the two handles have automatically locked the memory module into the correct position of the SODIMM socket. To remove the memory module, just push both handles outward, and the memory module will be ejected by the mechanism in the socket.

1.11

Cache Memory

The AIMB-562 KIOSK supports a CPU with one of the following built-in full speed L2 caches:

2048 MB for Intel Core 2 Duo CPU

1024 KB for Pentium dual core

1024 KB / 2048 KB for Pentium 4 CPUs

512 KB for Celeron D CPUs

The built-in second-level cache in the processor yields much higher performance than conventional external cache memories.

1.12

Processor Installation

The AIMB-562 KIOSK is designed for LGA775, Intel Pentium 4, Intel Core 2 Duo,

Celeron D and Intel Pentium dual core D processor.


Chapter

2

Connecting

Peripherals

2

2.1

Introduction

You can access most of the connectors from the top of the board as it is being installed in the chassis. If you have a number of cards installed or have a packed chassis, you may need to partially remove the card to make all the connections.

2.2

Parallel Port (LPT1)

LPT1

The parallel port is normally used to connect the motherboard to a printer. The AIMB-

562 KIOSK includes an onboard parallel port, accessed through a 25-pin flat-cable connector, LPT1.

Note!

Parallel cable is not enclosed in the box as a standard accessory. The order part number is 1700008809.


2.3

USB Ports (USB12/LAN2_USB34/USB56/USB78)

The AIMB-562 KIOSK provides up to eight ports of USB (Universal Serial Bus). The

USB interface complies with USB Specification Rev. 2.0 supporting transmission rates up to 480 Mbps and is fuse protected. The USB interface can be disabled in the system BIOS setup.

The AIMB-562 KIOSK is equipped with one high-performance 1000 Mbps Ethernet

LAN. They are supported by all major network operating systems. The RJ-45 jacks on the rear plate provide 1000Base-T operation.

USB12 LAN2_USB34

USB56/78

Table 2.1: LAN LED Indicator

LAN Mode

1 Gbps Link on

100 Mbps Link on

Active

Lan Indicator

LED1 Green on

LED1 Orange on

LED2 Green flash


2.4

VGA Connector (VGA1/VGA2)

VGA1/VGA2

The AIMB-562 KIOSK includes a VGA interface that can drive conventional CRT displays. VGA1/VGA2 is a standard 15-pin D-SUB connector commonly used for VGA.

Pin assignments for CRT connector VGA1/VGA2 are detailed in Appendix B.


2.5

Serial Ports (COM1~COM10)

1 3

2 4

COM 3456/78910

37 39

38 40

AIMB-562 KIOSK supports ten serial ports - eight RS-232, and two RS-232/422/485 -

COM3 and COM7. The user can use JSETCOM3/7 to select among RS 232/422/485 modes for COM3 and COM7. These ports can connect to serial devices, such as a mouse or a printer, or to a communications network.

The IRQ and address ranges for both ports are fixed. However, if you want to disable the port or change these parameters later, you can do this in the system BIOS setup.

Different devices implement the RS-232/422/485 standards in different ways. If you are having problems with a serial device, be sure to check the pin assignments for the connector.


2.6

PS/2 Keyboard and Mouse Connector (KBMS1)

KBMS1

Two 6-pin mini-DIN connectors (KBMS1) on the motherboard provide connection to a

PS/2 keyboard and a PS/2 mouse, respectively.


2.7

CPU Fan Connector (CPU_FAN1)

1

CPU_FAN1

If a fan is used, this connector supports cooling fans of 500 mA (6 W) or less.


2.8

System FAN Connector (SYS_FAN1)

1

2

3

SYS_FAN1

If a fan is used, this connector supports cooling fans of 500 mA (6 W) or less.


2.9

Front Panel Connectors (JFP1)

There are several external switches to monitor and control the AIMB-562 KIOSK.

JFP1

B

C

D

E

5 and 7

1 and 3

2 and 4

6 and 8

Reset switch

Hard drive activity LED

Power/Sleep/Waiting LED

Power switch

2.9.1

Power/Sleep Waiting LED (JFP1)

JFP1 pins 2 & 4 is a 2-pin connector for the power LED. Refer to Appendix B for detailed information on the pin assignments. If a PS/2 or ATX power supply is used, the system's power LED status will be as indicated below:

Table 2.2: ATX power supply LED status (No support for AT power)

Power mode

LED

(ATX Power Mode)

(On/off by tentative button)

PSON1

(On Back plane)

Jumper setting

2-3 pin closed

System On On

System Suspend Fast flashes

System Off Slow flashes

LED

(AT power Mode)

(On/off by switching power supply)

1-2 pin closed

On

Fast flashes

Off

LED

(AT power Mode)

(On/off by front panel switch)

Connect 1-2 pin cable with switch

On

Fast flashes

Off


2.9.2

Reset Connector (JFP1 pins 5 & 7)

Many computer cases offer the convenience of a reset button. Connect the wire from the reset button.

2.9.3

HDD LED Connector (JFP1 pins 1 & 3)

You can connect an LED to connector JFP2 to indicate when the HDD is active.

2.9.4

ATX Soft Power Switch (JFP1 pins 6 & 8)

If your computer case is equipped with an ATX power supply, you should connect the power on/off button on your computer case to JFP1 pins 1&2. This connection enables you to turn your computer on and off.

2.10

Line In, Line Out, Mic In Connector (AUDIO1)

AUDIO1

Line In

Line Out

Mic In


2.11

Serial ATA Interface (SATA1, SATA2)

SATA1, SATA2

AIMB-562 KIOSK features two high performance serial ATA interface (up to 300 MB/ s) which eases cabling to hard drives with thin and long cables.


2.12

ATX Power Connector (ATX12V1, EATXPWR1)

These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.

ATX12V

EATXPWR1

Note!

1.

Make sure that your ATX 12V power supply can provide 8A on the

+12V lead and at least 1A on the +5-volt standby lead (+5VSB).

The minimum recommended wattage is 230W, or 300W for a fully configured system. The system can become unstable and might experience difficulty powering up if the power supply is inadequate.

2.

You must install a PSU with a higher power rating if you intend to install additional devices.


2.13

SPI Flash Connector (SPI_CN1)

SPI flash card pin header which can be used to flash the BIOS.


2.14

Front Panel Audio Connector (FPAUDIO1)

This connector is for a chassis_mounted front panel audio I/O module that supports either HD Audio or legacy AC'97 (optional) audio standard. Connect one end of the front panel audio I/O module cable to this connector.

Note!

For motherboards with the optional HD Audio feature, we recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboardís high?definition audio capability.


2.15

System FAN Connector (SYS_FAN2)

GND

+12V

+5V

2.16

Primary EIDE Connector (IDE1)

1 3 37 39


2.17

USB 2.0 Connector (USB 56, 78)

These connectors are for USB 2.0 ports. Connect the USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.

Note!

The USB module is purchased separately.


2.18

LVDS Connector (JLVDS1)

2.19

LVDS Backlight Enabler (JBL1)


2.20

LVDS Power Jumper Selection1 (JLVDSPWR1)

3 2 1

2.21

Volume Adjustment Connector (VOLADJ1)

5 4 3 2 1

Note!

The volumn adjustment cable can be used to control the volumn. The cable need bought separately.


2.22

GPIO Pin Header (GPIO1, GPIO2)

1

Note!

GPIO1 Pin 1 ~ Pin 8 current: GPI: 5V 1uA. GPO: 5V 8~ 10uA.

GPIO2 Pin 1, 3, 5,7 current: GPO(output current only):5V,200mA

Pin 2, 4, 6, 8 current: GPI 5V, 1uA. GPO:5V, 8~10uA

GPIO2 Pin 1,3,5,7 are for 200mAT high current output use only.



Chapter

3

BIOS Operation

3

3.1

Introduction

Advantech provides full-featured AwardBIOS 6.0 and delivers the superior performance, compatibility and functionality that manufactures of Industry PC and Embedded boards, its many options and extensions let you customize your products to a wide range of designs and target markets.

The modular, adaptable AwardBIOS 6.0 supports the broadest range of third-party peripherals and all popular chipsets, plus Intel, AMD, nVidia, VIA, and compatible

CPUs from 386 through Pentium and AMD Geode, K7 and K8 (including multiple processor platforms), and VIA Eden C3 and C7 CPU.

You can use Advantech’s utilities to select and install features to suit your designs for customers need.

3.2

BIOS Setup

The AIMB-562 KIOSK KIOSK Series system has build-in AwardBIOS with a CMOS

SETUP utility which allows user to configure required settings or to activate certain system features.

The CMOS SETUP saves the configuration in the CMOS RAM of the motherboard.

When the power is turned off, the battery on the board supplies the necessary power to the CMOS RAM.

When the power is turned on, press the <Del> button during the BIOS POST (Power-

On Self Test) will take you to the CMOS SETUP screen.

Control Keys

< ↑ >< ↓ >< ← >< → >

Move to select item

<Enter> Select Item

<Esc>

Main Menu - Quit and not save changes into CMOS

Sub Menu - Exit current page and return to Main Menu

Increase the numeric value or make changes <Page Up/+>

<Page Down/->

<F1>

<F2>

<F5>

<F7>

<F10>

Decrease the numeric value or make changes

General help, for Setup Sub Menu

Item Help

Load Previous Values

Load Setup Default

Save all CMOS changes


3.2.1

Main Menu

Press <Del> to enter AwardBIOS CMOS Setup Utility, the Main Menu will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

Standard CMOS Features

This setup page includes all the items in standard compatible BIOS.

Advanced BIOS Features

This setup page includes all the items of Award BIOS enhanced features.

Advanced Chipset Features

This setup page includes all the items of Chipset configuration features.

Integrated Peripherals

This setup page includes all onboard peripheral devices.

Security chip configuration

This SETUP page includes all the items of Trusted Module Configuration features. This sub-menu item only appears when Trusted Module plug in.

Power Management Setup

This setup page includes all the items of Power Management features.

PnP/PCI Configurations

This setup page includes PnP OS and PCI device configuration.

PC Health Status

This setup page includes the system auto detect CPU and system temperature, voltage, fan speed.

Frequency/Voltage Control

This setup page includes CPU host clock control, frequency ratio and voltage.

Load Setup Defaults

This setup page includes Load system optimized value, and the system would be in best performance configuration.

Set Password

Establish, change or disable password.

Save & Exit Setup

Save CMOS value settings to CMOS and exit BIOS setup.

Exit Without Saving

Abandon all CMOS value changes and exit BIOS setup.


3.2.2

Standard CMOS Features

Date

The date format is <weekday>, <month>, <day>, <year>.

Weekday

Month

Day

Year

From Sun to Sat, determined and displayed by BIOS only

From Jan. to Dec.

From 1 to 31

From 1999 through 2098

Time

The time format is <hour> <minute> <second>, based on 24-hour time.

IDE Channel 0 Master/Slave

IDE HDD Auto-Detection Press "Enter" for automatic device detection.

Video

Select EGA or VGA display.

Halt on

The item determines whether the computer will stop if an error is detected during power up.

No Errors The system boot will not stop for any error.

All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.

All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other errors. (Default value)

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system.

Extended Memory

The BIOS POST will determine the amount of extended memory (above 1 MB in CPU’s memory address map) installed in the system.

Total Memory

This item displays the total system memory size.


3.2.3

Advanced BIOS Features

CPU Feature

This item allows user to adjust CPU features.

Hard Disk Boot Priority

This item allows user to select boot sequence for system device HDD, USB-

HDD, SCSI, RAID.

Virus Warning[Disabled]

Enables or disables the virus warning.

CPU L3 Cache

This item allows user to enable CPU L3 cache.

Quick Power On Self Test[Enabled]

This field speeds up the Power-On Self Test (POST) routine by skipping retesting a second, third and forth time. Setup setting default is enabled.

First / Second / Third / Other Boot Drive

Hard Disk

CDROM

USB-FDD

USB-ZIP

USB-CDROM

LAN

Disabled

Select boot device priority by Hard Disk.

Select boot device priority by CDROM.

Select boot device priority by USB-FDD.

Select boot device priority by USB-ZIP.

Select boot device priority by USB-CDROM.

Select boot device priority by LAN.

Disable this boot function.

Gate A20 Option [Fast]

This item enables users to switch A20 control by port 92 or not.

Typematic Rate Setting

This item enables users to set the two typematic controls items.

– Typematic Rate (Chars/Sec)

This item controls the speed at which the system registers auto-repeated keystrokes. The eight settings are 6, 8, 10, 12, 15, 20, 24 and 30.

– Typematic Delay (Msec)

This item sets the keypress time delay before autorepeat begins.

Four delay rate options are 250, 500, 750 and 1000.


Security Option [Setup]

System

Setup

System will not boot and refuses access to Setup page if the correct password is not entered at the prompt.

System will boot, but access to Setup requires password (default value).

APIC Mode [Enabled]

This item allows user to enabled of disabled “Advanced Programmable Interrupt Controller”. APIC is implemented in the motherboard and must be supported by the operating system, and it extends the number of IRQ's available.

3.2.4

Advanced Chipset Features

Note!

This “Advanced Chipset Features” page controls configuration of the board’s chipset. This page is chipset dependent; screens may differ somewhat depending on the chipset. It is strongly recommended that only technical users make changes to the default settings.

DRAM Timing Selectable [By SPD]

This item enables users to set the optimal timings for items 2 through 5; system default setting “By SPD” follows the SPD information and ensures the system runs stably with optimal performance.

CAS Latency Time [Auto]

This item enables users to set the timing delay in clock cycles before SDRAM starts a read command after receiving it.

DRAM RAS# to CAS# Delay [Auto]

This item enables users to set the timing of the transition from RAS (row address strobe) to CAS (column address strobe) as both rows and column are separately addressed shortly after DRAM is refreshed.

DRAM RAS# Precharge [Auto]

This item enables users to set the DRAM RAS# precharge timing, system default is setting to “Auto” to reference the data from SPD ROM.

Precharge delay (tRAS) [Auto]

This item allows user to adjust memory precharge time.


System Memory Frequency [Auto]

This item allows user to adjust memory frequency to improvement performance.

System BIOS Cacheable [Enabled]

This item allows the system BIOS to be cached to allow faster execution and better performance.

Video BIOS Cacheable [Disabled]

This item allows the video BIOS to be cached to allow faster execution and better performance.

Memory Hole At 15 M-16 M [Disabled]

This item reserves 15 MB-16 MB memory address space to ISA expansion cards that specifically require the setting. Memory from 15 MB-16 MB will be unavailable to the system because of the expansion cards can only access memory at this area.

PCI Express Root port Func [Press Enter]

This item allows the user to adjust PCIE port on, off or auto.

On-Chip Frame Buffer Size [8 MB]

This item allows the user to adjust the on-chip frame buffer size 8 MB or 1 MB.

DVMT Mode [DVMT]

This item allows the user to adjust Intel's Dynamic Video Memory Technology

(DVMT). BIOS provides three options: DVMT, FIXED, and Both.

DVMT/FIXED Memory Size [128MB]

This item allows the user to adjust DVMT/FIXED graphics memory size.

Init Display First

This item is the setting for start up video output: either from PCI Express or

Onboard device.


3.2.5

Integrated Peripherals

Note!

This “Integrated Peripherals” page controls the configuration of the board’s chipset, including IDE, ATA, SATA, USB, AC97, MC97 and

Super IO and Sensor devices. This page is chipset dependent; the screen capture above is illustrative, but screens do differ depending on chipset features.

OnChip IDE Device

This item enables users to set the OnChip IDE device status, including some of new chipsets also support SATA devices (Serial-ATA).

Onboard Device

This item enables users to set the Onboard device status, including enabling

USB, AC97, and LAN devices.


Super IO Device

This item enables users to set the Super IO device status, including enabling of

COM, LPT, and IR.

Onboard Serial port 1 [3F8 / IRQ4]

This item allows user to adjust serial port 1 of address and IRQ.

Onboard Serial port 2 [ 2F8/ IRQ3]


UART Mode Select [Normal]

This item allows you to select UART mode. The choices: “IrDA”, “ASKIR”, and

“Normal”.

RxD, TxD Active

This item allows you to determine the active level of the RxD and TxD serial lines. The choices: “Hi, Hi”, “Lo, Lo”, “Lo, H”, and “Hi, Lo”.

IR Transmission Delay

This item allows you to enable/disable IR transmission delay. The options are

“Enabled” and “Disabled”.


UR2 Duplex Mode

This item allows you to select the IR half/full duplex function. The options are

“Half” and “Full”.

Use IR Pins

The options are “RxD2, TxD2” and “IR-Rx2Tx2”.

Onboard Parallel Port [378/IRQ7]

This item allows user to adjust parallel port of address and IRQ.

Parallel Port Mode [ECP+EPP]

This item allows user to adjust parallel port mode.

EPP Mode Select [EPP1.9]

This field allows you to select EPP port type 1.7 or 1.9. The choices are

“EPP1.9” and “EPP1.7”.

ECP Mode Use DMA [3]

This item allows user to adjust ECP DMA resource.

Onboard Serial port 3 [3E8/IRQ10]


Onboard Serial port 4 [2E8/IRQ10]


3.2.6

Security Chip Configuration

3.2.7

TPM Support

The items in this menu allow you to set the TPM (Trusted Platform Module) features.

Select an item and then press <Enabled> to display the configuration options.

Note!

To enable the TPM function, set the TPM Support item to [Enabled] and then save the change; after rebooting, the TPM configuration menu will show the active options.


3.2.8

Power Management Setup

Note!

Adjust “Power management Setup” to configure the system to most effective energy savings still consistent with the intended style of use.

PCI Express PM Function

This allows you to control Power On by onboard LAN chip feature.

Power-Supply Type [ATX]

This item allows user to set power-supply type, ATX or AT mode.

ACPI Function [Enabled]

This item defines the ACPI (Advanced Configuration and Power Management) feature that makes hardware status information available to the operating system, and communicates with PC and system devices for improving the power management.

ACPI Suspend Type [S3(STR)]

This item allows user to select sleep state when in suspend.

S1(POS)

S3(STR)

The suspend mode is equivalent to a software power down;

The system shuts down with the exception of a refresh current to the system memory.

Run VGA BIOS if S3 Resume [Auto]

This item allows system to reinitialize VGA BIOS after system resume from

ACPI S3 mode.

Power Management [User Define]

This item allows user to select system power saving mode.

Min Saving

Max Saving

User Define

Minimum power management. Suspend Mode=1 hr.

Maximum power management. Suspend Mode=1 min.

Allows user to set each mode individually. Suspend Mode= Disabled or 1 min ~1 hr.


Video Off Method [DPMS]

This item allows user to determine the manner is which the monitor is blanked.

V/H SYNC+Blank This option will cause system to turn off vertical and horizontal synchronization ports and write blanks to the video buffer.

Blank Screen

DPMS

This option only writes blanks to the video buffer.

Initial display power management signaling.

Video Off In Suspend [Yes]

This item allows user to turn off video when system is in suspend mode.

Suspend Type [Stop Grant]

This item allows user to determine the suspend type.

Modem use IRQ [3]

This item allows user to determine which IRQ the MODEM can use.

Suspend Mode [Disabled]

This item allows user to set a delay time. If system inactivity exceeds the delay time, all devices except the CPU will be shut off.

Soft-Off by PWR-BTTN [Instant-Off]

This item allows user to define function of power button.

Instant-Off

Delay 4 Sec

Pressing power button initiates instant power off.

Press power button for four seconds to initiate power off.

PowerOn by LAN [Enabled]

This item allows user to power on the system via LAN. The choices are


PowerOn by Modem [Enabled]

This item allows user to power on the system by Modem. The choices are


USB KB Wake_Up From S3 [Disabled]

This item allows user to allow a USB keyboard to wake up the system from S3 suspend. Options: Enabled or Disabled.

PowerOn by Alarm [Disabled]

The choices are “Enabled” and “Disabled”. If enabled, the fields that follow indicate dates and times of alarm settings.

Primary IDE 0 (1) and Secondary IDE 0 (1) [Disabled]

When Enabled, the system will resume from suspend mode if Primary IDE 0 (1) or Secondary IDE 0 (1) becomes active. The choices are “Enabled” and “Disabled”.

FDD, COM, LPT PORT [Disabled]

When Enabled, the system will resume from suspend mode if the FDD interface, COM port, or LPT port becomes active. The choices are ”Enabled” and

“Disabled”.

PCI PIRQ [A-D]# [Disabled]

When Enabled, the system resumes from suspend mode if an interrupt occurs.

The choices are “Enabled” and “Disabled”.

PWRON After PWR-Fail [Former-Sts]

Use this to set up the system after power failure. The “Off” setting keeps the system powered off after power failure, the “On” setting boots up the system after failure, and the “Former-Sts” returns the system to the status before power failure.


3.2.9

PnP/PCI Configurations

Reset Configuration Data [Disabled]

The default is Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) if you have installed a new add-on card, and system configuration is in such a state that the OS cannot boot.

Resources Controlled By [Auto(ESCD)]

The commands here are “Auto(ESCD)” or “Manual”. Choosing “Manual” requires you to choose resources from the following sub-menu. “Auto(ESCD)” automatically configures all of the boot and Plug and Play devices, but you must be using Windows 95 or above.

PCI / VGA Palette Snoop [Disabled]

This is set to “Disabled” by default.

Maximum Payload Size [128]

This item shows you the maximum TLP payload size for PCI Express devices.

The option is set to [128 bytes] by chipset specification.


3.2.10

PC Health Status

ACPI Shutdown Temperature [Disabled]

The system will shut down automatically if the CPU temperature goes over the selected setting.

CPU Warning Temperature [Disabled]

The system will give an automatic warning if the CPU temperature goes over the selected setting.

Current System Temperature

This shows you the current temperature of system.

Current CPU Temperature

This shows the current CPU temperature.

VCORE and Other Voltages

This shows the voltage of VCORE, +3.3 V, +5 V, +12 V, -12 V, VBAT(V), and 5

VSB (V).


3.2.11

Load Setup Defaults

Note!

Load Setup Defaults loads the default system values directly from ROM.

Useful if the stored record created by the Setup program should ever become corrupted (and therefore unusable).

3.2.12

Set Password

Note!

To enable this feature, you should first go to the Advanced BIOS Features menu, choose the Security Option, and select either Setup or System, depending on which aspect you want password protected. “Setup” requires a password only to enter Setup. “System” requires the password either to enter Setup or to boot the system. A password can be at most 8 characters long.


To Establish Password

1.

Choose the Set Password option from the CMOS Setup Utility main menu and press <Enter>.

2.

When you see “Enter Password”, enter the desired password and press

<Enter>.

3.

At the “Confirm Password” prompt, retype the desired password, then press

<Enter>.

4.

Select Save to CMOS and EXIT, type <Y>, then <Enter>.

To Change Password

1.


2.

When you see “Enter Password”, enter the existing password and press

<Enter>.

3.

You will see “Confirm Password”. Type it again, and press <Enter>.

4.

Select Set Password again, and at the “Enter Password” prompt, enter the new password and press <Enter>.

5.

At the “Confirm Password” prompt, retype the new password, and press

<Enter>.

6.


To Disable Password

1.


2.

When you see “Enter Password”, enter the existing password and press

<Enter>.

3.

You will see “Confirm Password”. Type it again, and press <Enter>.

4.

Select Set Password again, and at the “Enter Password” prompt, please don’t enter anything; just press <Enter>.

5.

At the”Confirm Password” prompt, again, don’t type in anything; just press

<Enter>.

6.



3.2.13

Save & Exit Setup

Note!

Typing “Y” will quit the BIOS Setup Utility and save user setup values to

CMOS.

Typing “N” will return to BIOS Setup Utility.

3.2.14

Quit without Saving

Note!

Typing “Y” will quit the BIOS Setup Utility without saving to CMOS.

Typing “N” will return to BIOS Setup Utility.



Chapter

4

Chipset Software

Installation Utility

4

4.1

Before you begin

To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for the AIMB-562 KIOSK are located on the software installation CD. The driver in the folder of the driver CD will guide and link you to the utilities and drivers under a Windows system. Updates are provided via Service Packs from Microsoft*.

Note!

The files on the software installation CD are compressed. Do not attempt to install the drivers by copying the files manually. You must use the supplied SETUP program to install the drivers.

Before you begin, it is important to note that most display drivers need to have the relevant software application already installed in the system prior to installing the enhanced display drivers. In addition, many of the installation procedures assume that you are familiar with both the relevant software applications and operating system commands. Review the relevant operating system commands and the pertinent sections of your application software’s user manual before performing the installation.

4.2

Introduction

The Intel

®

Chipset Software Installation (CSI) utility installs the Windows INF files that outline to the operating system how the chipset components will be configured.

This is needed for the proper functioning of the following features:

Core PCI PnP services

IDE Ultra ATA 100/66/33 and Serial ATA interface support

USB 1.1/2.0 support (USB 2.0 driver needs to be installed separately for Win98)

Identification of Intel

®

chipset components in the Device Manager

Integrates superior video features. These include filtered sealing of 720 pixel

DVD content, and MPEG-2 motion compensation for software DVD

Note!

This utility is used for the following versions of Windows, and it has to be installed before installing all the other drivers:

Windows 2000

Windows XP

Windows Vista


4.3

Windows XP Driver Setup

1.

Insert the driver CD into your system's CD-ROM drive. You can see the driver folder items. Navigate to the "INF" folder and click "setup.exe" to complete the installation of the driver.



Chapter

5

VGA Setup

5

5.1

Introduction

The Intel 945G/945GC integrated graphics controller. You need to install the VGA driver to enable the function.

The Intel 945G/945GC integrated graphics controller includes the following features:

Intel Graphics Media Accelerator 950: Incorporating the latest Microsoft*

DirectX*9 support capabilities, it allows software developers to create lifelike environments and characters. Dual independent display, enhanced display modes for widescreen flat panels, and optimized 3D support deliver an intense and realistic visual experience without requiring a separate graphics card.

5.2

Windows Vista/XP/2000

Note!

Before installing this driver, make sure the CSI utility has been installed in your system. See Chapter 4 for information on installing the CSI utility.

Insert the driver CD into your system's CD-ROM drive. You can see the driver folders items. Navigate to the "VGA" folder and click "setup.exe" to complete the installation of the drivers for Vista, Windows XP, and Windows 2000.




Chapter

6

LAN Configuration

6

6.1

Introduction

The AIMB-562 KIOSK has a single/dual Gigabit Ethernet LAN via dedicated PCI

Express x 1 bus (Realtek RTL8111C), which offers bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet to operate at 1000 Mbps.

6.2

Features

Integrated 10/100/100 BASE-T transceiver

10/100/1000 BASE-T triple-speed MAC

High-speed RISC core with 24-KB cache

On-chip voltage regulation

Wake-on-LAN (WOL) support

PCI Express X1 host interface

6.3

Installation

Note!

Before installing the LAN drivers, make sure the CSI utility has been installed on your system. See Chapter 4 for information on installing the

CSI utility.

The AIMB-562 KIOSK Realtek RTL8111C Gigabit integrated controller supports all major network operating systems. However, the installation procedure varies with different operating systems. Please find and use the section that provides the driver setup procedure for the operating system you are using.

6.4

Win XP/Vista Driver Setup (Realtek RTL8111C)

Insert the driver CD into your system's CD-ROM drive. Select the Drv_LAN folder then navigate to the directory for your OS.




Appendix

A

A

Programming the

Watchdog Timer

A.1


The AIMB-562 KIOSK's watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to program it.

A.1.1

Watchdog timer overview

The watchdog timer is built into the super I/O controller W83627DHG. It provides the following user-programmable functions:

Can be enabled and disabled by user program

Timer can be set from 1 to 255 seconds or 1 to 255 minutes

Generates an interrupt or resets signal if the software fails to reset the timer before time-out

A.1.2


The I/O port address of the watchdog timer is 2E (hex) and 2F (hex). 2E (hex) is the address port. 2F (hex) is the data port. You must first assign the address of register by writing an address value into address port 2E (hex), then write/read data to/from the assigned register through data port 2F (hex).


Unlock W83627DHG

Select register of watchdog timer

Enable the function of the watchdog timer

Use the function of the watchdog timer

Lock W83627DHG


Table A.1: Watchdog Timer Registers

Address of register (2E) Attribute

Read/Write

Value (2F) & description

87 (hex)

07 (hex)

30 (hex)

F5 (hex)

F6 (hex)

F7 (hex)

AA (hex)

----write write write write read/write

-----

Write this address to I/O address port 2E (hex) twice to unlock the W83627DHG.

Write 08 (hex) to select register of watchdog timer.

Write 01 (hex) to enable the function of the watchdog timer. Disabled is set as default.

Set seconds or minutes as units for the timer.

Write 0 to bit 3: set second as counting unit.

[default]

Write 1 to bit 3: set minutes as counting unit.

0: stop timer [default]

01~FF (hex): The amount of the count, in seconds or minutes, depends on the value set in register F5

(hex). This number decides how long the watchdog timer waits for strobe before generating an interrupt or reset signal. Writing a new value to this register can reset the timer to count with the new value.

Bit 7:Write 1 to enable mouse to reset the timer, 0 to disable[default]. Bit 6: Write 1 to enable keyboard to reset the timer, 0 to disable.[default]

Bit 5: Write 1 to generate a timeout signal immediately and automatically return to 0. [default=0]

Bit 4: Read status of watchdog timer, 1 means timer is “timeout”.

Write this address to I/O port 2E (hex) to lock the watchdog timer 2.


A.1.3

Example Program

1.

Enable watchdog timer and set 10 sec. as timeout interval

;-----------------------------------------------------------

Mov dx,2eh ; Unlock W83627DHG

Mov al,87h

Out dx,al

Out dx,al

;-----------------------------------------------------------

Mov al,07h ; Select registers of watchdog timer

Out dx,al

Inc dx

Mov al,08h

Out dx,al

;-----------------------------------------------------------

Dec dx ; Enable the function of watchdog timer

Mov al,30h

Out dx,al

Inc dx

Mov al,01h

Out dx,al

;-----------------------------------------------------------

Dec dx ; Set second as counting unit

Mov al,0f5h

Out dx,al

Inc dx

In al,dx

And al,not 08h

Out dx,al

;-----------------------------------------------------------

Dec dx ; Set timeout interval as 10 seconds and start counting

Mov al,0f6h

Out dx,al

Inc dx

Mov al,10

Out dx,al

;-----------------------------------------------------------

Dec dx ; Lock W83627HG

Mov al,0aah

Out dx,al

2.

Enable watchdog timer and set 5 minutes as timeout interval

;-----------------------------------------------------------

Mov dx,2eh ; Unlock W83627HG

Mov al,87h

Out dx,al

Out dx,al


;-----------------------------------------------------------


Out dx,al

Inc dx

Mov al,08h

Out dx,al

;-----------------------------------------------------------


Mov al,30h

Out dx,al

Inc dx

Mov al,01h

Out dx,al

;-----------------------------------------------------------

Dec dx ; Set minute as counting unit

Mov al,0f5h

Out dx,al

Inc dx

In al,dx

Or al,08h

Out dx,al

;-----------------------------------------------------------

Dec dx ; Set timeout interval as 5 minutes and start counting

Mov al,0f6h

Out dx,al

Inc dx

Mov al,5

Out dx,al

;-----------------------------------------------------------


Mov al,0aah

Out dx,al

3.

Enable watchdog timer to be reset by mouse

;-----------------------------------------------------------


Mov al,87h

Out dx,al

Out dx,al

;-----------------------------------------------------------


Out dx,al

Inc dx

Mov al,08h

Out dx,al

;-----------------------------------------------------------



Mov al,30h

Out dx,al

Inc dx

Mov al,01h

Out dx,al

;-----------------------------------------------------------

Dec dx ; Enable watchdog timer to be reset by mouse

Mov al,0f7h

Out dx,al

Inc dx

In al,dx

Or al,80h

Out dx,al

;-----------------------------------------------------------


Mov al,0aah

Out dx,al

4.

Enable watchdog timer to be reset by keyboard

;-----------------------------------------------------------


Mov al,87h

Out dx,al

Out dx,al

;-----------------------------------------------------------


Out dx,al

Inc dx

Mov al,08h

Out dx,al

;-----------------------------------------------------------


Mov al,30h

Out dx,al

Inc dx

Mov al,01h

Out dx,al

;-----------------------------------------------------------

Dec dx ; Enable watchdog timer to be strobed reset by keyboard

Mov al,0f7h

Out dx,al

Inc dx

In al,dx

Or al,40h

Out dx,al


;-----------------------------------------------------------


Mov al,0aah

Out dx,al

5.

Generate a time-out signal without timer counting

;-----------------------------------------------------------


Mov al,87h

Out dx,al

Out dx,al

;-----------------------------------------------------------


Out dx,al

Inc dx

Mov al,08h

Out dx,al

;-----------------------------------------------------------


Mov al,30h

Out dx,al

Inc dx

Mov al,01h

Out dx,al

;-----------------------------------------------------------

Dec dx ; Generate a time-out signal

Mov al,0f7h

Out dx,al ;Write 1 to bit 5 of F7 register

Inc dx

In al,dx

Or al,20h

Out dx,al

;-----------------------------------------------------------


Mov al,0aah

Out dx,al


Appendix

B

B

I/O Pin Assignments

B.1

Parallel Port (LPT1)

Table B.1: Parallel Port (LPT1)

Pin

7

8

5

6

3

4

1

2

9

10

11

12

13

Signal

D3

D4

D5

D6

STROBE*

D0

D1

D2

D7

ACK*

BUSY

PE

SLCT

* Low activity

B.2

USB Header (USB56)

Pin

18

19

20

21

14

15

16

17

22

23

24

25

26

Signal

AUTOFD*

ERR

INIT*

SLCTINI*

GND

GND

GND

GND

GND

GND

GND

GND

N/C

Table B.2: USB Header (USB56)

Pin

5

7

1

3

9

Signal

USB0_VCC5

USB0_D-

USB0_D+

GND

Key

Pin

6

8

2

4

10

Signal

USB1_VCC5

USB1_D-

USB1_D+

GND

GND


B.3

USB Header (USB78)

Table B.3: USB Header (USB78)

Pin

1

3

5

7

9

Signal

USB0_VCC5

USB0_D-

USB0_D+

GND

Key

B.4

VGA Connector (VGA1)

Pin

2

4

6

8

10

Signal

USB1_VCC5

USB1_D-

USB1_D+

GND

GND

Table B.4: VGA Connector (VGA1)

Pin

6

7

4

5

8

1

2

3

Signal

RED

VGA_G

VGA_B

N/C

GND

GND

GND

GND

Pin

12

13

14

15

9

10

11

Signal

CRT_VCCIN

GND

N/C

V_SDAT

H-SYNC

V-SYNC

V_SCLK


B.5

VGA Connector (VGA2)

Table B.5: VGA Connector (VGA2)

Pin

7

8

5

6

3

4

1

2

Signal

RED

VGA_G

VGA_B

N/C

GND

GND

GND

GND

Pin

13

14

15

9

10

11

12

B.6

RS-232 Interface (COM1-COM2)

9 7 5 3 1

Signal

CRT_VCCIN

GND

N/C

V_SDAT

H-SYNC

V-SYNC

V_SCLK

10 8 6 4 2

Table B.6: RS-232 Interface (COM1~COM2)

Pin

6

7

4

5

8

9

1

2

3

Signal

DCD

DSR

RXD

RTS

TXD

CTS

DTR

RRI

GND


B.7

RS-232/422/485 Setting Interface

(JETCOM3456~78910)

Table B.7: RS-232/422/485 Setting Interface (JETCOM3456~78910)

Pin Signal Pin Signal

9

11

13

15

17

5

7

1

3

R_SINA

R_SINA

R_SINA

DCDA

COM1_DCD#

COM1_TXD485N

SINA

COM1_SIN

COM1_TXD485P

10

12

14

16

18

6

8

2

4

RXD485_1

RXD422_1

RXD232_1

SOUTA

COM1_SOUT

COM1_RXD485P

DTRA

COM1_DTR#

COM1_RXD485N

B.8

RS-232 Interface (COM3456)

Table B.8: RS-232 Interface(3456)

Pin Signal

23

25

27

29

15

17

19

21

31

33

35

37

7

9

11

13

1

3

5

39 GND

COM3 is RS-232/422/485.

COM3_1

COM3_2

COM3_3

COM3_4

GND

DDCD4#

RRXD4

TTXD4

DDTR4#

GND

DDCD5#

RRXD5

TTXD5

DDTR5#

GND

DDCD5#

RRXD6

TTXD6

DDTR6#

73

Pin

32

34

36

38

40

24

26

28

30

16

18

20

22

8

10

12

14

2

4

6

Signal

DDSR3#

RRTS3#

CCTS3#

RRI3#

GND

DDSR4#

RRTS4#

CCTS4#

RR14#

GND

DDSR5#

RRTS5#

CCTS5#

RRI5#

GND

DDSR6#

RRTS6#

CCTS6#

RRI6#

GND

AIMB-562 KIOSK User Manual

B.9

RS-232 Interface (COM78910)

Table B.9: RS-232 Interface (COM78910)

Pin

23

25

27

29

15

17

19

21

31

33

35

37

39

7

9

11

13

1

3

5

Signal

COM7_1

COM7_2

COM7_3

COM7_4

GND

DDCD8#

RRXD8

TTXD8

DDTR8#

GND

DDCD9#

RRXD9

TTXD9

DDTR9#

GND

DDCD9#

RRXD10

TTXD10

DDTR10#

GND

Pin

24

26

28

30

16

18

20

22

32

34

36

38

40

8

10

12

14

2

4

6

COM7 is RS-232/422/485.

Signal

DDSR7#

RRTS7#

CCTS7#

RRI7#

GND

DDSR8#

RRTS8#

CCTS8#

RR18#

GND

DDSR9#

RRTS9#

CCTS9#

RRI9#

GND

DDSR10#

RRTS10#

CCTS10#

RRI10#

GND


B.10

SPI_CN1: SPI fresh card pin connector

1

7

2

8

5

7

1

3

Table B.10: SPI_CN1:SPI fresh card pin connector

Pin Signal Pin Signal

+F1_3V

F1_SPI_CS#_Q

F1_SPI_MISO_Q

NC

6

8

2

4

GND

F1_SPI_CLK_Q

F1_SPI_MOSI_Q

NC

B.11

PS/2 Keyboard and Mouse Connector (KBMS1)

Table B.11: PS/2 Keyboard and Mouse Connector (KBMS1)

Pin

7

8

5

6

3

4

1

2

9

10

11

12

Signal

KB DATA

N/C

GND

KB VCC

KB CLK

N/C

M_DATA

N/C

GND

M_VCC

M_CLK

N/C


B.12

CPU Fan Power Connector (CPU_FAN1)

1

Table B.12: CPU Fan Power Connector (CPU_FAN1)

Pin

1

2

3

4

Signal

GND

+12 V

DETECT

PWM

B.13

System Fan Power Connector (SYS_FAN1/

SYS_FAN2)

1

2

3

Table B.13: System Fan Power Connector (SYSFAN1/SYSFAN2)

Pin

1

2

3

Signal

GND

+12 V

DETECT

B.14

Front Panel Connectors (JFP1)

1

2


B.14.1

Power/Sleep LED (JFP1)

2 4

Table B.14: Power/Sleep LED (JFP1)

Pin

2

4

Signal

LED power (+5 V)

LED power (+5 V)

B.14.2

Reset Connector (JFP1)

5 7

Table B.15: Reset Connector (JFP1)

Pin

5

7

Signal

RESET

GND

B.14.3

HDD LED Connector (JFP1)

12

1 3

Table B.16: HDD LED Connector (JFP1)

Pin

1

3

Signal

IDE LED+

IDE LED-

B.14.4

ATX Soft Power Switch (JFP1)

6 8

Table B.17: ATX Soft Power Switch (JFP1)

Pin

6

8

Signal

5 VSB

PWR-BTN


B.15

ATX1 12 V Auxiliary Power Connector

(ATX12V1)

3

4

1

2

Table B.18: ATX1 12 V Auxiliary Power Connector (ATX12V1)

Pin Signal

GND

GND

+12 V

+12 V

B.16

ATX Power Connector (EATXPWR1)

Table B.19: ATX Power Connector (ATX2)

Pin

7

9

11

13

1

3

5

15

17

19

Signal

+3.3 V

GND

GND

GND

5 VSB

12 V

3.3 V

GND

GND

GND

Pin

8

10

12

14

2

4

6

16

18

20

Signal

+3.3 V

+5 V

+5 V

POK

12 V

3.3 V

-12 V

PSON

GND

-5 V


B.17

USB/LAN ports (LAN2_USB12/USB34)

12

12

34

34

1

2

Table B.20: USB Port

Pin Signal

VCC

Data0-

Pin

3

4

Signal

Data0+

GND

3

4

1

2

Table B.21: Ethernet 10/100Base-T RJ-45 Port

Pin Signal Pin

XMT+

XMT-

RCV+

N/C

7

8

5

6

B.18

Line Out, Mic In Connector (AUDIO1)

Signal

N/C

RCV-

N/C

N/C

B.19

Serial ATA0 (SATA1)

Table B.22: Serial ATA0 (SATA1)

Pin

1

3

5

7

Signal

GND

SATA_0TX-

SATA_0RX-

GND

Pin

2

4

6

8

Line Out

Mic In

Signal

SATA_0TX+

GND

SATA_0RX+


B.20

Serial ATA1 (SATA2)

5

7

1

3

Table B.23: Serial ATA1 (SATA2)

Pin Signal

GND

SATA_1TX-

SATA_1RX-

GND

B.21

AT/ATX Mode (PSON1)

Pin

6

8

2

4

Table B.24: AT/ATX Mode (PSON1)

Pin

1

3

Signal

#PSON_SIO

(to super IO)

GND

Pin

2

B.22

JLVDS1: LVDS connector

Table B.25: LVDS Connector (JLVDS1)

Pin

23

25

27

29

15

17

19

21

31

33

35

37

39

7

9

11

13

1

3

5

Signal

OD1+

GND

OD2-

OD2+

GND

OCK-

OCK+

GND

VDDSAFE

GND

VDDSAFE

OD0-

OD0+

GND

OD1-

DDC_CLK

GND

OD3-

OD3+

HPLG

Pin

24

26

28

30

16

18

20

22

32

34

36

38

40

8

10

12

14

2

4

6


Signal

SATA_1TX+

GND

SATA_1RX+

Signal

#PSON

(to power supply)

Signal

ED1+

GND

ED2-

ED2+

GND

ECK-

ECK+

GND

VDDSAFE

GND

VDDSAFE

ED0-

ED0+

GND

ED1-

DDC DAT

GND

ED3-

ED3+

VCON

B.23

JBL1(LVDS inverter connector)

Table B.26: LCD Inverter Power Connector (JBL1)

Pin

1

2

3

4

5

Signal

VCC12_INV1

GND

LVDS_BKLTEN

VBR

VP3_P5

B.24

JLVDSPWR1(LVDS power jumper selection)

1

2

3

Table B.27: LVDS power jumper selection (JLVDSPWR1)

Pin Signal

3.3 V

+LVDS_PWR_SEL

5 V

1-2 pin

2-3 pin

3.3 V

5 V

B.25

FPAUDIO1(Front Panel Audio Connector)

Table B.28: Front Panel Audio Connector (FPAUDIO1)

Pin Signal

5

6

7

8

1

2

3

4

9

10

MIC2_L

AGND

MIC2_R

PRESENSE

LIN2_R

GND

FIO_JD

N/A

LIN2_L

GND


B.26

GPIO12(GPIO pin header)

Table B.29: GPIO pin header(GPIO1)

Pin

1

2

3

4

Signal

DIO_GP20

DIO_GP24

DIO_GP21

DIO_GP25

Pin

5

6

7

8

Signal

DIO_GP22

DIO_GP26

DIO_GP23

DIO_GP27

3

4

1

2

Table B.30: GPIO pin header(GPIO2)

Pin Signal Pin

DIO_GP10

DIO_GP14

DIO_GP11

DIO_GP15

7

8

5

6

Signal

DIO_GP12

DIO_GP16

DIO_GP13

DIO_GP17

GPIO1 Pin 1 ~ Pin 8 current: GPI: 5V 1uA. GPO: 5 V 8 ~ 10 uA.

GPIO2 Pin 1, 3, 5, 7 current: GPO (output current only): 5 V, 200 mA

Pin 2, 4, 6, 8 current: GPI 5 V, 1 uA. GPO:5 V, 8~ 10 uA

GPIO2 Pin 1, 3, 5, 7 are for 200mAT high current output use only.

B.27

VOLADJ1(Volumn Adjustment connector)

Table B.31: Volumn Adjustment connector (VOLADJ1)

Pin

1

2

3

4

5

Signal

AMP_L_OUT_C

AMP_L_OUT

GND

AMP_R_OUT

AMP_R_OUT_C

B.28

System I/O Ports

Table B.32: System I/O Ports

Addr. range (Hex)

000-01F

022-023

040-05F

060-06F

070-07F

080-09F

0A0-0BF

Device

Interrupt controller 1, master

Chipset address

8254 timer

8042 (keyboard controller)

Real-time clock, non-maskable interrupt (NMI) mask

DMA page register

Interrupt controller 2


Table B.32: System I/O Ports

0C0-0DF

0F0

0F1

0F8-0FF

1F0-1F8

200-207

278-27F

290-297

2F8-2FF

Serial port 2

360-36F

378-37F

380-38F

3A0-3AF

3B0-3BF

3C0-3CF

3D0-3DF

3F0-3F7

3F8-3FF

DMA controller

Clear math co-processor

Reset math co-processor

Math co-processor

Fixed disk

Game I/O

Parallel printer port 2 (LPT3)

On-board hardware monitor

Serial port 2

Prototype card

Reserved

Parallel printer port 1 (LPT2)

SDLC, bisynchronous 2

Bisynchronous 1

Monochrome display and printer adapter (LPT1)

Reserved

Color/graphics monitor adapter

Diskette controller

Serial port 1

B.29

JCASE1(Open Case Connector)

3

4

1

2

Table B.33: Case Open Connector(JCASE1)

Pin Signal

+5VSB

N/A

ICH_INTRUDER#

GND

B.30

DMA Channel Assignments

6

7

4

5

2

3

0

1

Table B.34: DMA Channel Assignments

Channel Function

Available

Available

Floppy disk (8-bit transfer)

Available

Cascade for DMA controller 1

Available

Available

Available


B.31

Interrupt Assignments

Table B.35: Interrupt Assignments

Priority

11

12

13

14

7

8

9

10

15

16

5

6

-

4

1

2

3

Interrupt#

IRQ11

IRQ12

IRQ13

IRQ14

IRQ15

IRQ3

IRQ4

IRQ5

IRQ6

IRQ7

NMI

IRQ0

IRQ1

IRQ2

IRQ8

IRQ9

IRQ10

Interrupt source

Parity error detected

Interval timer

Keyboard

Interrupt from controller 2 (cascade)

Real-time clock

Cascaded to INT 0A (IRQ 2)

Serial communication port 3/4

Available

PS/2 mouse

INT from co-processor

Primary IDE Channel

Secondary IDE Channel

Serial communication port 2

Serial communication port 1

Available

Diskette controller (FDC)

Parallel port 1 (print port)

B.32

1st MB Memory Map

Table B.36: 1st MB Memory Map

Addr. range (Hex)

E0000h - FFFFFh

CC000h - DFFFFh

C0000h - CBFFFh

A0000h - BFFFFh

00000h - 9FFFFh

Device

BIOS

Unused

VGA BIOS

Video Memory

Base memory



www.advantech.com

Please verify specifications before quoting. This guide is intended for reference purposes only.

All product specifications are subject to change without notice.

No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher.

All brand and product names are trademarks or registered trademarks of their respective companies.

© Advantech Co., Ltd. 2009

Advantech AIMB-562 KIOSK User manual

Assistant Bot

User Manual

Intel

®

LGA775 Core™ 2 Duo mATX Motherboard with Dual

VGA/LVDS/DDR2/10 COM/LAN

Copyright

Acknowledgements

A Message to the Customer

Declaration of Conformity

CPU Compatibility

Memory Compatibility

Ordering Information

Product Warranty (2 years)

Initial Inspection

Contents

General Information

Connecting Peripherals

Programming the Watchdog Timer

I/O Pin Assignments

General Information

Introduction

Features

Specifications

System

Memory

Input/Output

Graphics

Ethernet LAN

Industrial features

Mechanical and environmental specifications

Jumpers and Connectors

Board layout: Jumper and Connector Locations

AIMB-562 KIOSK Block Diagram

Safety Precautions

Jumper Settings

How to set jumpers

CMOS clear (CMOS1)

Volumn adjustment(VOLADJ1)

Chassis instruction connector (JCASE1)

ATX/AT mode selector (PSON1)

AT switch connector(AT_SWITCH1)

COM3/7 RS 232/422/485 mode selector (JSETCOM3456/78910)

LVDS power jumper connector(JLVDSPWR1)

System Memory

Memory Installation Procedures

Cache Memory

Processor Installation

Connecting

Peripherals

Introduction

Parallel Port (LPT1)

USB Ports (USB12/LAN2_USB34/USB56/USB78)

VGA Connector (VGA1/VGA2)

Serial Ports (COM1~COM10)

PS/2 Keyboard and Mouse Connector (KBMS1)

CPU Fan Connector (CPU_FAN1)

System FAN Connector (SYS_FAN1)

Front Panel Connectors (JFP1)

Power/Sleep Waiting LED (JFP1)

Reset Connector (JFP1 pins 5 & 7)

HDD LED Connector (JFP1 pins 1 & 3)

ATX Soft Power Switch (JFP1 pins 6 & 8)

Line In, Line Out, Mic In Connector (AUDIO1)

Serial ATA Interface (SATA1, SATA2)

ATX Power Connector (ATX12V1, EATXPWR1)

SPI Flash Connector (SPI_CN1)

Front Panel Audio Connector (FPAUDIO1)

System FAN Connector (SYS_FAN2)

Primary EIDE Connector (IDE1)

USB 2.0 Connector (USB 56, 78)

LVDS Connector (JLVDS1)

LVDS Backlight Enabler (JBL1)

LVDS Power Jumper Selection1 (JLVDSPWR1)

Volume Adjustment Connector (VOLADJ1)

GPIO Pin Header (GPIO1, GPIO2)

BIOS Operation

Introduction

BIOS Setup