Radio control model
R/C Flugmodell
INSTRUCTION MANUAL
MONTAGEANLEITUNG
THUNDERBOLT
Designed for brushless electric motors
Entwickelt für Brushless Elektro Motoren
VQ No: VQA0100
TECHNISCHE DATEN
SPECIFICATIONS
Spannweite
Lange
Elektroantrieb
Fernsteuerung
Wingspan
Length
Electric Motor
Radio
1220mm
1000mm
(siehe nächste Seite)
4 Kanal / 4 Servos
1220mm.
1000mm.
(See next page)
4 Channel / 4 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
RECOMMENDED ACCESSORIES
Empfohlenes Zubehör
4 x Servo S2112
mit 500mm Servokabel
Antrieb Tuning (Kraftvoller Kunstflug):
BOOST 25 Brushless Combo Set, No. C2981
LiPo Akku RED POWER 2200-3S, No. C2158
Propeller 10*5, No. C5749
4 - channel radio
4 - Kanal
Fernsteuerung
MASTER, No. 5374
EPOXY A
SILICON
Cyanoacrylate Glue
Sekundenkleber
CA
Silicon Glue
Silikonkleber
EPOXY B
Epoxy Glue (30 minutes type)
Epoxy-Klebstoff (30min)
Tool Required/ Empfohlenes Werkzeug
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
Drill holes using the stated
1.5mm size of drill
(in this case 1.5 mm Ø)
!
Take particular care here
A B
Use epoxy glue
CA
CONVERSION TABLE
3.0mm = 1/8”
1.0mm = 3/64”
4.0mm = 5/32”
1.5mm = 1/16”
5.0mm = 13/64”
2.0mm = 5/64”
6.0mm = 15/64”
2.5mm = 3/32”
Apply cyano glue
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
Hatched-in areas:
remove covering
film carefully
Assemble left and right
L/R sides the same way.
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
!
Check during assembly that these
parts move freely, without binding
X
Not included.
These parts must be
purchased separately
1
1-Slide the vertical and horizontal stabilizer on the fuselage, use a pencil to trace
around the bottom and the top (horizontal stabilizer) and the right and the left
(vertical stabilizer).
2-Remove the vertical and horizontal stabilizer from the fuselage. Careful cut
away the covering inside the lines which were marked in steep 1.
1A
Cut away only the
covering both the
left and right side*
1B
Note: Check the alignment of the horizontal stabilizer by measuring from
a fixed point along the center line of the fuselage to the leading edge on
each side of the horizontal stabilizer. The distance must be equal on both
sides. If not, adjust the stabilizer until the measurements are the same.
Thin CA
Cut away only the covering both
the top and bottom side*
CA
1C
Realign the vertical stabilizer and horizontal stabilizer, then glue
the vertical stabilizer and horizontal stabilizer into the fuselage,
using a generous amount of thin CA.
Note: glue both the right and left of the vertical stabilizer, and
both the top and bottom of the horizontal stabilizer.
Attach the Vertical Stabilizer and the Horizontal Stabilizer
B’
B
A
2
A’
B’
B
A
A’
Correct
Incorrect
Incorrect
A=A’ B=B’
/
A=A’
/
B=B’
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Thin CA
CA
Apply thin CA to both
side of the hinge
Hinge
STABILIZER
CA
Push the elevator and its hinges into the hinge slots in the trailing
edge of the horizontal stabilizer.
There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the
horizontal stabilizer using thin CA glue.
3
CA
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Thin CA
CA
Note: The slots for the control horn
installation are pre- cut at factory.
Control horn
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!
...........1
4
4B
4A
Thin CA
5
Push the rudder and its hinges into the hinge slots in the trailing edge of the
horizontal stabilizer. There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal
stabilizer using CA glue.
CA
A=30mm
A
CA
Thin CA
5A
2mm
Drill a 2mm diameter hole in torque rod
mounting slot, marking sure that you
drill the hole perpendicular to the leading
edge of the rudder.
CA
A B
Hinge
5 minute
25mm tail wheel
2mm collar
Apply thin CA to both
side of the hinge
5B
STABILIZER
6
6A
6B
Rudder linkage
FUSELAGE - BOTTOM VIEW
The holes for the rudder servo
are Pre-cut at factory..
Cut away only the covering
FUSELAGE - BOTTOM VIEW
6C
Elevator linkage
FUSELAGE - BOTTOM VIEW
7
Using a ply gear mount plate as a template, mark the square
plastic where the holes are to be drilled (7A).
3X12mm screw
Plastic strap
Ply gear mount
plate
7A
Square plastic
Square plastic
7C
Gear mount
(hard wood)
7B
7D
EXTENDED POSITION
8
GEAR
OFF
RECEIVER
ON
RETRACTED POSITION
ELECTRIC RETRACT
LANDING GEAR
Retract landing gear
not included.
8A
8B
WING - BOTTOM VIEW
9
Ply gear mount
9A
WING - BOTTOM VIEW
10
WING - BOTTOM VIEW
1-Using the ply gear mount as a template, trace around the
outside edge of the ply gear mount, and then remove it.
2-Using a sharp hobby knife, cut away the covering and balsa
along the lines.
CA
9B
11
WING - BOTTOM VIEW
12
NOTE: Do not glue the bottom hatch onto the
wing at this time.
CA
13
CA
14
49mm
Note: Position the motor on to the fire-wall so the
distance from the prop hub to the fire wall is 49mm.
2x10mm screw
15
Uberprufen Sie vor dem Flug den Schwerpunkt.
Do not try to fly an out-of balance model!
Aileron / Querruderausschlag
8mm
8mm
Rudder
15mm
Seitenruderausschlag
15mm
Elevator / Hohenruderausschlag
10mm
10mm
85~90 mm
CG
IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner
to clean on surface of your model to keep the colour not fade.
All details are subject to change
Technische Anderungen und Irrtumer
without notice !
vorbehalten !
">
