VQ Focke-Wulf FW-190A Instruction Manual
The vq FOCKE-WULF FW-190A is a radio-controlled model aircraft designed for experienced hobbyists. It features a 2-cycle engine with a displacement of 60 to 70cc and a wingspan of approximately 59 inches. The model is constructed from durable EPOXY A and EPOXY B materials, ensuring its resilience during flight. With its realistic design and powerful engine, the vq FOCKE-WULF FW-190A offers a thrilling flying experience for model aircraft enthusiasts.
PDF
Download
Document
Advertisement
Advertisement
45 Class 2-cycle engine 70 Class FOCKE-WULF FW - 190A 4-cycle engine Or Electric equivalent RADIO CONTROL MODEL VQA0450L VQA044G/Y INSTRUCTION MANUAL 46~50 (7.45cc) 5~6 60~70 (11.5cc) 6 lb. (2700g) Wingspan approx. 59 in. (1500mm) Fuselage length approx 43 in. (1090mm) Warning: This radio control model is not a toy. If modified or flow carelessly it could go out of control and cause serious bodily injury or property damage. Before flying your airplane, ensure the air field is spacious enough. Always fly it outdoors in safe areas with no debris or obstacles. REQUIRED FOR OPERATION (Purchase separately) 10.5x6 for .40 - 2 cycle engine 11x6 for .46 - 2 cycle engine 12x6 for .60 - 4 cycle engine 12x7 for .70 - 4 cycle engine Silicone tube Extension for aileron servo, retract servo and power pack Retract landing gear VQAR04 - 160224 Minimum 5 channel radio for airplane with 5 servos .Motor control x1 .Aileron x2 .Elevator x1 .Rudder x1 .46 ~ .50 - 2 cycle .60 ~.70 - 4 cycle Linkage Stopper x2 (for retract servo) GLUE (Purchase separately) SILICON Retract servo x1 EPOXY A Cyanoacrylate Glue Silicon sealer EPOXY B CA Epoxy Glue ( 5 minute type) Epoxy Glue (30 minute type) TOLLS REQUIRED (Purchase separately) Hex Wrench Hobby knife Awl Phillip screw driver Needle nose Pliers Scissors Wire Cutters Sander ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... Masking tape - Straight Edged Ruler - Pen or pencil - Rubbing alcohol - Drill and Assorted Drill Bits The pre-covered film on ARF kit may wrinkle due to variations of temperature. Smooth out as explained right. * Use an iron or heat gun. Start as low setting. Increase the setting if necsessary. If it is too high, you may damage the film Low setting Symbols used throughout this instruction manual, comprise: Drill holes using the stated 1.5mm size of drill (in this case 1.5 mm Ø) ! A B Use epoxy glue CA Take particular care here Apply cyano glue Hatched-in areas: remove covering film carefully Assemble left and right L/R sides the same way. Check during assembly that these parts move freely, without binding X Not included. These parts must be purchased separately Read through the manual before you begin, so you will have an overall idea of what to do. Bottom view Ansicht von unten 1- Retract landing gear / Fahwerk Trial fit the push rod into the wing. Join the pushrod to the retract gear arm and trial fit the retract into the wing. 3x12mm screw 3x12mm schraube After checking that the retract works smoothly, fix the retract on the wing with 3x12mm screws X L/R Retract pushrod Fahrwerkanlenkgestange 2mm Steel clevis .........2 3x12mm screw ................8 2- Aileron servo / Querruder servo Bottom view / Ansicht von unten Aileron extension cord Servoverlangerungskabel X ....................2 2x20mm screw ...............4 Aileron servo Querruder servo 40mm Plastic control horn X X Included with the radio set 2mm 15mm 3- Joining the wing / Flache Secure one end of the aileron Use epoxy glue to bury the opening extension cord with adhesive tape Nehmen Sie Epoxykleber, um die Tragflachen fest miteinander zu Verbinden und streifen Sie den herausquellenden Kleber nach dem Verbinden mit einem fusselfreien Tuch SOFORT ab! Wing joiner Tragflachenverbinde Center line 1- Using a pencil, mark the center of the brace. 2- Trial fit the wing joiner into one of the wing panels. It should insert smoothly up to the center line marked above. 3- Slide the other wing half onto the dihedral brace until the wing panel meet. If the fit is over tight, it may be necessary to lightly sand the dihedral brace. 4- Check for the correct dihedral angle. 5- Mix approximately 30 minute epoxy and apply a generous amount of epoxy into the wing joiner cavity of one wing half. 6- Coat one half of the dihedral brace with epoxy up to the center line. Install the epoxy-coated side of the dihedral brace into the wing joiner cavity up to the center line, marking sure that the “V” of the dihedral brace is positioned correctly 7- Do the same way with the other wing half. 8- Carefully slide the wing halves together, ensuring that they are accurately aligned. Firmly press the two halves together, allowing the excess epoxy to run out. Clear off the excess epoxy. 4- Servo mount / Servohalterung A Retract servo mount (plywood A,B,C) Einziehfahrwerk servohalterung Schneiden Sie etwas Folie weg Cut away only the covering FWU1 FWU2 CA CENTER WING SECTION CA A FWU2 FWU1 BOTTOM CA CA 5- Retract servo / Einziehfahrwerk servo Install the retract servo onto the retract servo mount and secure it in place with four screw (included with radio set). Retract servo Einbau des Servos fur das Einziehfahrwerk X Einbau des Servos fur / Retract servo das Einziehfahrwerk CENTER WING SECTION BOTTOM 6- Linkages / Ruderanlenkung 8-5/16”(~210mm) RETRACT PUSHROD (SIDE VIEW) Fahrwerkanlenkgestänge 1”(25mm) Instruction how to build in the retracting landing gear (This Gearis OPTIONAL ) Einbauhilfe bei Anbringen eines Einziehfahrwerks (Optional 2” (~50mm) bestellbar; nicht im Baukasten enthalten!) 19/64” (7.5mm) (TOP VIEW) With the retract and retract servo in the retracted position, mark the position where each of the pushrod will attach to the servo arm, a small piece of masking tape works well for this. Cut off the excess length each rod. Link the servo and retract gear arm with push rod. Be sure to adjust the stroke so EINGEFAHREN that the landing gear locks in both up and down position. AUSGEFAHREN 7- Fixed gear / Landegestange Landegestänge Main gear (left) Kunststoffstreifen Plastic strap 3x10mm Befestigungsklötze für Landegestänge Gear mount (hard wood) Gear mount (hard wood) CA Main gear (right) Landegestänge Ply gear mount plate Square plastic Ply gear mount plate Plastic strap Kunststoffstreifen Main landing gear Landegestänge 3x10mm 3x10mm screw ..............16 Square plastic 8- Fixed gear / Landegestange ABS wheel well cover ABS gear cover 4mm collar 3x10mm screw 3x10mm schraube/screw ..........8 2x6mm schraube/screw ..........4 4mm stellring/collar ..........2 ABS gear cover 2x6mm screw 1.5mm CA ABS gear strap CA Bottom view / Ansicht von unten Gear mount (hard wood) 9- Horizontal stabilizer / Hohenruder Schneiden Sie etwas Folie weg Cut away only the covering* Cut away only the covering both side* Cut away only the covering both side* C = C’ A = A’ A A’ C 1-Trial fit the horizontal stabilizer in place . Check the alignment of the horizontal stabilizer. When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the stabilizer where it meets the fuselage. 2-Remove the horizontal stabilizer from the fuselage. Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above. 3-Spread epoxy (30 minute) onto the top and bottom of the horizonApply the epoxy tal stabilizer along the area where both side the covering was removed and to A B the fuselage where the horizontal stabilizer mounts. 4-Install the horizontal stabilizer into the fuselage and adust the alignment as described in steep 1l Allow the epoxy to cure before proceeding to next step. C’ Securely glue together. If coming off during flight, you lose control of your air plane! Vergewissern Sie sich, sauber geklebt zu haben. Andernfalls konnen Probleme mit der Flugeigenschaft auftreten! WARNING: Please do not clean off the excess epoxy on the wing with strong solvent or pure alcohol, only use kerosene to keep the colour of your model not fade. 10- Vertical stabilizer / Hohenleitwerk 1-Trial fit the vertical stabilizer in place . Check the alignment of the vertical stabilizer. When you are satisfied with the alignment, use a pencil to trace around the right and left of the stabilizer where it meets the fuselage. 2-Remove the vertical stabilizer from the fuselage. Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above. 3-Spread epoxy (30 minute) onto the right and left and bottom of the vertical stabilizer along the area where the covering was removed and to the fuselage where the vertical stabilizer mounts. 4-Install the vertical stabilizer into the fuselage and adust the alignment as described in steep 1.l Allow the epoxy to cure before proceeding to next step. Cut away only the covering both side* Apply the epoxy both side A B B’ B Vergewissern Sie sich, sauber geklebtzu haben. Andernfalls konnen Probleme mit der Flugeigenschaft auftreten! B=B’ Securely glue together. If coming off during flight, you lose control of your air plane! * WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement. This will ensure the covering remain tight. 11- Elevator / Hohenruder Apply a thin layer of machine oil or petroleum jelly to only the pivot point of the hinges on the elevator, then push the elevator and its hinges into the hinge slots in the trailing edge of the horizontal stabilizer. There should be a minimal hinge gap and the end of the elevator should not rub against the horizontal stabilizer. When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using 5 minute epoxy. Make sure to apply a thin layer of epoxy to the top and bottom of both hinges and to inside the hinge slots. Repeat the previous procedures to hinge the second elevator to the other side of the horizontal stabilizer. A B CA CA Apply thin CA both the top and bottom. STABILIZER Hinge Securely glue together. If coming off during flight, you lose control of your air plane! Bottom view 12- Control horn / Ruderhorn Ansicht von unten Plastic control horn ...................3 5 O 2x12mm screw ...............6 5 O 3/8” (10mm) 2mm 2mm 2x12mm screw 2x12mm Blechschraube Rudder servo(not include) Seitenruderservo 13- Servo NOTE: Place of servos may be change depend of engine (Four-stoke or two-stroke engine) Throttle servo(not included) Drosselservo Switch installation Switch collar Switch hole Elevator servo(not included) Bottom view Hohenruderservo Ansicht von unten 14- Linkages / Ruderanlenkung Switch pushrod (not included) Connector Gestangeanschluss ............1 Bottom view Ansicht von unten Elevator pushrod Rudergestange Throttle pushrod Connector Gestangeanschluss ............3 Rudder pushrod Throttle servo / Drosselservo Rudder servo /Seitenruderservo Elevator servo /Hohenruderservo 2mm screw Rudergestange Throttle pushrod Elevator pushrod Rudergestange Rudder pushrod Throttle / Drosselservo 2mm screw Gestangeanschluss Connector Elevator pushrod Rudergestange Elevator servo / Hohenruderservo 15- Tail wheel / Spornrad Bottom view Ansicht von unten Tail wheel mount Bottom view Ansicht von unten Horn (1) Collar Gewindestift Gear 9/16”(14mm) Tail gear mount Horn Fuselage 3x12mm screw 5/16”(8mm) Rudder 1.5mm Side view CA 1.5mm (1) Piece of fuel tube (not included) NOTE: Check the wheel turns freely. 4x25mm screw 16- Engine mount / Motortrager ...4 Blind-nut ! Align the mark on both engine mount beams with the mark on the fuselage .............4 ! Engine thrust on balk head is already adjust at factory A B A B’ FRONT-VIEW B=B’ 3/16” 5mm Attach the engine mount beams onto the fire-wall so the distance between of two engine mount beams is “A”. Secure the engine mount beams onto the fire-wall with litter CA glue. Using a pencil or felt tipped pen, mark the fire wall where the four holes are to be drilled. Carefully remove the engine mount beams and drill a 3/16”(5mm) hole through the fire-wall at each of the four marks made above. Insert the blind-nut onto each of the four holes make above. Reposition the engine mount beams on to the fire-wall and secure them with four 4x25mm screw. 17- Engine / Motoreinbau Position the engine onto the engine mount beams so the distance from the prop hub to the end of engine mount beams is 4-3/8” (110mm). 4-3/4”(110mm) 3mm 3x25mm screw ...4 .........4 TOP-VIEW 1.5 Secure the engine with four 3x20mm screw ! Engine thrust on balk head is already adjust at factory 18- Engine / Motor 2-Takt IN CASE OF TWO-STROKE ENGINE In case of two-stroke engine with hang muffler. Silencer extension adaptor (not include) In case of two-stroke engine with the silencer extension adapter. In case of two-stroke engine with side silencer. Secure the engine with four 3x25mm screw 19- Electric motor/Elektromotor Plywood motor mounting plate (2pcs) FRONT-VIEW - Using a plywood motor mounting plate as a template, mark the fire wall where the four holes are to be drilled (1). - Remove the plywood motor mounting plate and drill a 13/64”(5mm) hole through the fire-wall at each of the four marks marked (2). - Using a aluminum motor mounting plate as a template, mark the plywood motor mounting plate where the four holes are to be drilled (3). - Remove the aluminum motor mounting plate and drill a 1/8”(3mm) hole through the plywood at each of the four marks marked (4). Aluminum motor -Push the four 5x70mm bolts through the fire-wall as shown (5). mounting plate 1 2 13/64” 5mm ! Align the mark on the plywood motor mount with the mark on the fuselage. - Reposition the plywood motor mounting plate (2pcs) and secure it in place with eight 5mm nuts and washers (6). Note: B=B’(Side-view) and A=A’(Top-view) -Attach the aluminum motor mounting plate on to the motor and secure it in place with four screws ( included with motor set) (7). -Attach the motor on to the plywood motor mounting plate and secure it in place with four 3x15mm (1/8x19/32”) screws(8). 3 4 1/8” 3mm ! Align the mark on the plywood motor mount with the center lines on aluminum motor mount. 5 6 7-8 B SIDE-VIEW B=B’ Firewall A TOP-VIEW A=A’ A’ B’ 125~127mm (5-1/8”) ! Engine thrust on balk head is already adjust at factory 5x70mm.......4 5mm nut.......12 5mm washer...16 3mm screw/nut...4 20- Li-Po battery stand installation 1 Remove the magnetic battery hatch out of the fuselage. Battery hatch Akkuklappe SIDE-VIEW / Seitenansicht the battery stand into the fuselage 2 Put as show (left). Secure the battery stand to the fuselage using the CA glue (below). CA Li-Po battery stand Li-Po battery stand (3mm plywood) SIDE-VIEW / Seitenansicht CA 3 BOTTOM - VIEW Unteransicht Install the Li-Po battery into the battery area to ensure that they will not shift during flight. Again, put the magnetic battery hatch in place. Battery hatch Akkuklappe SIDE-VIEW / Seitenansicht 21- Fuel tank / Kraftstofftank To muffler Filler tube Rubber stopper X To engine Aluminum stopper Aluminum cap Push the fuel tank forward until there are no gaps between the tank and firewall. 5/32”(4mm) 3x35 mm screw After confirming the direction . Insert and tighten the screw. 22- Cowling / Motorhaube 2.5x10mm screw ..........4 Adhesive tape Attach the board or transparent plastic on the side of the fuselage with the adhesive tape as show. Using a pencil or felt tipped pen trace around the engine head where it meet the cowl. Cut the opening the board or transparent plastic for the engine head as marked above. 1 Adhesive tape Remove the engine and insert the cowl onto the fuselage so the distance from the fire wall to the front of the cowl is 4-3/4”(110mm). Using a pencil or felt tipped pen trace around the inside of the engine head hole on the board or the transparent plastic made in step 1. This mark will serve as the guides for cutting the engine head hole on the cowl in next step. Board or transparent plastic 2 Cut the opening the board or the transparent plastic. 3 Ruler 4 Remove the cowl from the fuselage and carefully cut the opening for the engine head through as marked above. Do the same way with the hole for needle-valve. Cut the opening the cowl 5 3/32” 2.5mm Reposition the engine onto the engine mount beams and secure it with four 3x25mm screw. Again, insert the cowl onto the fuselage and secure it in place with four 2.5x10mm screw. NOTE: Do the same way in case of two-stroke engine. 25- ABS parts / ABS Teile Use 150 grit sandpaper to “rough up” the surface on the bottom of the slots of cowl where the gun-barre meets the cowl. Mix a small amount of 5minute epoxy to glue the gun-barres onto the cowl.(do not use CA glue because it will make the gun-barres and the cowl white). Install the other gun-barres onto the leading edge of the wing. CA A B 27- Decor / Aufkleber VQAO44G/Y Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off with scissors. Arrange sticker on model and when satisfied adhere the corner without backing. Carefully peel back the rest of the backing while at the same time adhering the rest of the sticker. Try not to make air bubbles, if there are some, carefully puncture sticker (center of bubble) but not model surface with the tip of the knife or sharp pin and squeeze out the air. At curves stretch sticker and apply a little heat so that no ceases occur. Cut off the excess that is produced. 28- Balance Schwerpunkt 4-1/2”(107 mm) VQA045OL DO NOT try to fly an out-of-balance model ! Wing center section To get the correct C.G., Several strips of lead weight were required in the nose of this model . IMPORTANT: Recheck the C.G. After the weight has been installed. Securely install the battery, ensuring it will not come loose or rattle during flights. Flatform (3.2mm ply) Battery pack Baterie Basswood stick Setzten Sie den Empfanger und das Akku-Pack fest ein und gehen Sie sicher, dass sich diese wahrend des Fluges nich losen oder wackein. Lead should be permanently glued on flatform with epoxy 29- Control surface / Ruderausschlage 1/4” (6mm) 1/4” (6mm) AILERON / QUERRUDER 25/64”(10mm) 1-3/16”(30) mm RUDDER / SEITENRUDER 1-3/16”(30) mm 25/64”(10mm) ELEVATOR / HOHENRUDER IMPORTANT: Flying your model at these throws will provide you with the greatest chance for successful first flights. If, after you have become accustomed to the way the Fw-190 flies, you would like to change the throws to suit your taste that is fine. However, too much control throw could make the model difficult to control, so remember, “more is not always better”. WARNING Do not put in a large-than recommended engine. A bigger engine does not necessarily mean better performance. IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner to clean on surface of your model to keep the colour not fade. All details are subject to change without notice ! Technische Anderungen und Irrtumer vorbehalten ! ">

Public link updated
The public link to your chat has been updated.
Advertisement