Manual (Standard)

FL-2R MOVING HEAD 120W
USER MANUAL
Ver1.0
Table of contents
1. Preface
1.1 Packing list
1.2 Unpacking instructions
1.3 AC Power
1.4 Safety instructions
2. Introduction
2.1 Features
2.2 DMX channel
3. Setup
3.1 Fuse replacement
3.2 Fixtur e linking
Data cabling
DMX data cable
3.3 3-Pin to 5-Pin conversion chart
3.4 Setting up a DMX serial data link
3.5 Master/Slave fixture linking
3.6 orientation
4. Operating instructions
4.1 Menu m ap
4.2 DMX channel values
5. Technical specifications
1. Preface
1.1 Packing list
Product name
Moving head light
Powercon in cable
Powercon extension cord
Mounting Bracket
Unser manual
quantity
1 pcs
1 pcs
1 pcs
2 pcs (attached)
1pcs
1.2 Unpacking instructions
On receiving a fixture, carefully unpack the carton, check the contents to ensure
that all parts are presented, and have been received in a good condition. Notify
the shipper immediately and retain packing material for inspection if any parts
appear damaged from shipping or the carton itself shows sign of mishandling.
Save the carton and all packing materials. In the event that a fixture must be
returned to the factory , it is important that the fixture should be returned in
original factory box and packing.
1.3 AC Power
To determine the power requirements for a particular fixture, see the label
affixed to the back plate of the fixture or referred to the fixtures specification
chart. A fixture listed current rating is its average current draw under normal
conditions. All fixtures must be directly powered off a switched circuit and cannot
be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or
dimmer source voltage matches the fixtures requirement. Check the fixture or
device carefully to make sure that if a voltage selection switch exist that it is set
to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your fixture may result if the line voltage applied
does not match the voltage indicated on the voltage selector switch. All fixtures
must be connected to circuits with a suitable Earth ground.
1.4 Safety instructions
Please read these instructions because, it includes important information about
the installation, usage and maintenance of this product.
Please keep this user guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the
line voltage you are connecting to is not higher than that stated on the decal or
rear panel of the fixture.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make
sure that there are no flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least
20in(50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing fuse and be
sure to replace with same fuse size and type.
Secure fixture to fastening device using a safety chain. Never carry the fixture
solely by its head. Use its carrying handles.
Maximum ambient temperature (Ta) is 104℉(40℃). Do not operate fixture at
temperatures higher than this.
In the event of a serious operating problem, stop using the unit immediately.
Never try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
Don’t connect the device to a dimmer device.
Make sure the power cord never crimped or damaged.
Never disconnect the power cord by pulling for the cord.
Avoid direct eye exposure to the light source while it is on.
2. Introduction
2.1 Features
14 channel DMX-512 .
Pan :540 / tilt:270o,Pan / Tilt no limit.
Color wheel : 13 colors+open,rainbow effect.
Gobo wheel : 14 gobos +open,gobo wheel spin effect.
Variable electronic strobe.
Variable electronic dimmer(0-100%).
LED display menu with invert.
Reset to factory settings option.
Pan/tilt invert option.
Optional controllers.
2.2 DMX channel
Channel
Function
1
Color wheel
2
Strobe
3
Dimmer
4
Gobo wheel
5
Prism
6
Prism rotating
7
Focus
8
Pan
9
Pan fine
10
Tilt
11
Tilt fine
12
Pan /tilt speed
13
Lamp switch
14
Reset
3. Setup
Disconnect the power cord before replacing a fuse and always replace with the
same type fuse.
3.1 Fuse replacement
With a flat head screwdriver wedge the fuse hold out of its housing. Remove the
damaged fuse from its holder and replace with exact same type fuse. Insert the
fuse holder back in its place and reconnect power.
3.2 Fixture linking
You will need a serial data link to run light show of one or more fixtures using a
DMX-512 controller or to run synchronized on two or more fixtures set to a
master/slave operating mode. The combined number of channels required by all
the fixtures on a serial data link determines the number of fixtures the data link
can support.
Maximum recommended serial data link distance:500 meters(1640ft).
Maximum recommended number of fixtures on a serial data link:32 fixtures.
Data cabling
To link fixtures together you must obtain data cables. If you choose to create
your own cable please use data-grade cables that can carry a high quality signal
and are less prone to electromagnetic interference.
DMX data cable
Use a belden 9841 or equivalent cable which meets the specifications for EIA
RS-485 applications. Standard microphone cables cannot transmit DMX data
reliably over long distances. The cable will have the following characteristics:
2-conductor twisted pair plus a shield.
maximum capacitance between conductors-30 pF/ft.
maximum capacitance between conductor and shield -55 pF/ft.
maximum resistance of 20 ohms/1000ft.
nominal impedance 100-140 ohms.
3.3
3-Pin to 5-Pin conversion chart
Note! If you use a controller with a 5 pin DMX output connector. you will need to
use a 5pin to 3 pin adapter
CHAUVET Model No:DMX5M. or DMX 5F
The chart below details a proper cable conversion:
3.4 Setting up a DMX serial data link
at first link the first light and DMX control through XLR-connection signal cable,
then join the light in series ,as the follow
3.5 Master/Slave fixture linking
1.Connect the (male) 3 pin connector side of the DMX cable to the output
(female)3pin connector of the first fixture.
2.Connect the end of the cable coming from the first fixture which will have a
(female)3 pin connector to the input connector of the next fixture consisting of a
(male) 3 pin connector. Then, proceed to connect from the output as stated
above to the input of the following fixture and so on.
3.6 or ientation
This fixture may be mounted in any position provided there is adequate room for
ventilation.
4. Operating instructions
4.1 Menu map
1.SETUP
DM X M O D
AU TO M OD
AD J U S T
E SC
2.OPTI ON
PAN
T ILT
DI S P LAY
COL O R
L AM P
CH IN E S E
E SC
3.INFORMATION
DI S P LAY S Y S TE M
X Y MO TOR S YS TE M
T IN Y M O TO R S Y S TE M
L AM P
FI X TU R E
E SC
4.MANUAL CONTROL
COL O R
S T RO B E
DI M M E R
G OBO
PR I S M IN S
PR I S M RO T
FO CUS
PAN
PA N FI N E
T ILT
TI LT F I N E
PAN RO TATE
TILT RO TATE
X Y S P E ED
L AM P O F F
RE S E T
E SC
5.RESET
A LL R E S E T
XY RESET
GO BO R E S E T
CO LO R R E S E T
FO CU S R E S E T
DI M ME R RE S E T
PR I S M R ES E T
FRO S T R S E S T
PRISM M RESET
FA CTO RY D E FAU LT
E SC
6.ESC
DMX mode
This mode allows the until to be controlled by any universal DMX controller.
The default mode for the fixture is DMX, as follow.
4.2 DMX channel values
Channel
1
Value
0-8
9-17
18-28
27-35
36-44
45-53
54-62
63-71
72-80
81-89
90-98
99-107
108-116
117-127
128-191
192-127
2
3
4
0-4
5-251
252-255
0-255
0-4
5-9
10-14
15-19
20-24
25-29
30-34
35-39
40-44
45-49
50-54
55-59
60-64
65-69
70-71
72-113
114-118
119-160
161-165
166-172
173-179
180-186
Function
Color wheel
No color
Color1
Color2
Color3
Color4
Color5
Color6
Color7
Color8
Color9
Color10
Color11
Color12
Color13
Color wheel positive turn, slow to fast
Color wheel reversal turn, slow to fast
Strobe
No
Slow to fast
Light ON
Dimmer
0-100%
Gobo wheel
No
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo7
Gobo8
Gobo9
Gobo10
Gobo11
Gobo12
Gobo13
Gobo14
Gobo wheel positive turn, fast to slow
Light ON, effect stop
Gobo wheel reversal speed, slow to fast
Light ON, effect stop
Gobo2 shake, slow to fast
Gobo3 shake, slow to fast
Gobo4 shake, slow to fast
187-193
194-200
201-207
208-214
215-221
222-228
229-235
236-242
243-249
250-255
5
6
7
8
9
10
11
12
0-127
128-255
0-127
128-190
191-192
193-255
Gobo5 shake, slow to fast
Gobo6 shake, slow to fast
Gobo7 shake, slow to fast
Gobo8 shake, slow to fast
Gobo9 shake, slow to fast
Gobo10 shake, slow to fast
Gobo11 shake, slow to fast
Gobo12 shake, slow to fast
Gobo13 shake, slow to fast
Gobo14 shake, slow to fast
Prism
No effect
Prism effect
Rotating prism
Gobo positioning
Forward rotating prism
slow to fast
Stop rotating
Reverse rotating prism
slow to fast
Focus
0-255
Pan
0-255
Pan fine
0-255
Tilt
0-225
Tilt fine
0-255
0-225
13
101-110
201-255
14
120-149
170-255
Pan /tilt speed
Speed from fast to slow
Lamp switch
Light OFF
Light ON
Reset
reset(delay 3 second)
Auto
5. techno-specification
Lamp socket
Color housing
Voltage
Pan
Tilt
Tiptop environment temperature
Date input/output
N.W
Packing size
Phillips MSD Platinum 2r or similar
black
120-240V 50/60Hz
540°,Pan no limit
270°,Tilt no limit
104°F(40°C)
3pin XLR-connection powercon socket
10.2kg
G.W
12.2kg(1pcs/package)
400×320×520mm(L×W×H)(1pcs/package)