INSTRUCTION MANUAL

Before commencing assembly, please read these instructions thoroughly.

Specifications

Wing Span: 50 in / 1270 mm

Wing Area: 484 sq in / 31.2 sq dm

Flying Weight: 3.5 lbs / 1600 g

Fuselage Length: 44.5 in / 1130 mm

Requires: (Engine powered) 2-stroke 0.40 engine

4-channel radio w/ 4 standard servos

(Electric powered) 450W motor system

4-channel radio w/ 3 standard servos

40A brushless ESC with 11x8E propeller, 4 cells

14.8V 3200 mAh Li- Po battery & charger

Warning ! This model is not a toy.

It is designed for maximum performance. Please seek advice if one is not familiar with this kind of engine(electric) powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference.

* Specifications are subject to change without notice.*

THE WINGS MAKER

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY (ARF) SERIES

MADE IN CHINA www.thewingsmaker.com

GA029PO22471104

INDEX

BEFORE YOU BEGIN

PARTS LIST

ASSEMBLY

SAFETY PRECAUTIONS

BEFORE YOU BEGIN

P.1

P.2

P.3-P.11

P.11

1

Read through the manual before you begin, so you will have an overall idea of what to do.

2

Check all parts. If you find any defective or missing parts contact your local dealer. Please

DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.

Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.

3

Symbols used throughout this instruction manual comprise of the following :-

Apply epoxy glue.

Apply instant glue

(C.A.glue, super glue.)

Apply thread locker Must be purchased separately!

Assemble left and right sides the same way.

3mm

Peel off shaded portion covering film.

Drill holes with the specified diameter (here: 3mm)

Pay close attention here!

Ensure smooth non-binding movement while assembling.

Cut off shaded portion.

Pierce the shaded portion covering film.

Do not overlook this symbol!

GA029PO22471104

P.1

Parts List

1. MAIN WING -- 1 pair

2. WING JOINER 6x18x180mm -- 1 pc.

3. FUEL TUBE d2xD4x4 mm -- 4 pcs

CLEVIS -- 2 pcs

STRAPER -- 2 pcs

RING Ø2.3mm -- 2 pcs

PUSHROD Ø1.4x110mm w/ Threads ( For Aileron) -- 2 pcs

PLYWOOD 2x8x22mm (For Aileron Servo) -- 1 pc.

PLYWOOD 4x8x22mm (For Aileron Servo) -- 1 pc.

4. STABILIZER & ELEVATOR -- 1 set

FUSELAGE -- 1 pc.

5. VERTIACL FIN & RUDDER -- 1 set

SCREW PM3x60mm -- 2 pcs

WASHER d3xD7mm -- 2 pcs

6. MAIN LANDING GEAR -- 1 pair

COLLAR Ø3.1mm w/ set screw -- 4 sets

WHEEL Ø55mm -- 2 pcs

SCREW PA3x10mm -- 4 pcs

MOUNTING PLATE 12x20mm -- 2 pcs

7. TAIL LANDING GEAR -- 1 set

COLLAR Ø2.1mm w/ set screw -- 1 set

WHEEL Ø23mm -- 1 pc.

STEERING BRACKET -- 1 pc.

SCREW PA3x8mm -- 2 pcs

SCREW PM2x10mm -- 1 pc.

M2 NUT -- 1 pc.

8. SCREW PB2x10mm -- 2 pcs

FUEL TUBE d2xD4x4mm -- 1 pc.

CLEVIS -- 1 pc.

HORN -- 1 set

PUSHROD Ø1.4x655mm w/ Threads (For Elevator) -- 1 pc.

9. SCREW PB2x10mm -- 2 pcs

FUEL TUBE d2xD4x4mm -- 1 pc.

CLEVIS -- 1 pc.

HORN -- 1 set

PUSHROD Ø1.4x655mm w/ Threads (For Rudder) -- 1 pc.

GA029PO22471104

P.2

10.SPINNER Ø52mm -- 1 pc.

11. STRAPER -- 2 pcs

FUEL TUBE d2xD4x4mm -- 2 pcs

SPONGE 10x80x200mm -- 2 pcs

12. SCREW PM2x10mm -- 2 pcs

WASHER d2xD5mm -- 2 pcs

M2 NYLON INSERT LOCK NUT -- 2 pcs

MOUNTING PLATE (PL4114015) -- 2 pcs

PLYWOOD 2x67.5x94.3mm -- 1 pc.

PLYWOOD 2x67.4x133mm -- 1 pc.

13. SCREW HM3x25mm -- 2 pcs

WASHER d3xD7mm -- 2 pcs

PLASTIC PLATE 1x15x80mm -- 1 pc.

14. CANOPY -- 1 pc.

SCREW PWA 2.3x8mm -- 4 pcs

15. DECALS: GA029 DEC -- 1 set

COVERING:--

LIGHTEX SGX 201 BLACK

TOUGHLON STL 311 FERRARI RED

TOUGHLON STL 330 CADMINU YELLOW

TOUGHLON STL 540 PEARL GREEN

TOUGHLON STL GA029 RED/WHITE

TOOGHLON STL GA029 RED/YELLOW

TOUGHLON STL GA029 GREEN/WHITE

1

Main Wing Apply epoxy glue to the linkage wire BEFORE applying instant type CA glue to both sides of each hinge.

2

1

2

Main Wing

Wing Joiner

Completed

Please dry fit wing joiner into left and right wing to make sure they fit with the proper dihedral angle, mark the wing joiner if necessary. Apply epoxy glue to both sides of all surfaces in contact. Use a stick to apply the glue to inner side of wing joiner sleeve, and apply the glue to wing joiner before putting them together. Wing joiner not glued properly will lead to wing failure and plane crash.

3

Aileron Servo

Plywood

4x8x22mm

Plywood

2x8x22mm

1.5mm

Ring

Straper

Fuel Tube d2xD4x4mm

Clevis

GA029PO22471104

TWM PL8210010

CLEVIS WRENCH

P.3

Completed

4

B

Stabilizer & Elevator

(Stabilizer)

B

(Main Wing)

B=B

Temporary install the main wing, adjust leveling of the stabilizer to make is as parallel to the main wing as possible.

A A

A=A

Apply instant type CA glue to both sides of each hinge.

5

Vertical Fin & Rudder

PM3x60mm

Screw

2 d3xD7mm

Washer

2

C

C=C

C

Apply instant type CA glue to both sides of each hinge.

Completed

PM3x60mm d3xD7mm

Washer

6

Main Landing Gear

PA3x10mm

Screw

4

3.1mm

Collar

4

3.1mm Collar

3mm Set Screw

GA029PO22471104

Mounting Plate

Bottom View

P.4

1.5mm

PA3x10mm

Completed

7

Tail Landing Gear

PM2x12mm

Screw

1

M2

Nut

1

PA3x12mm

Screw

2

2.1mm

Collar

1

Steering Bracket

M2

Nut

8

Elevator Pushrod

PB2x10mm

Screw

2

PB2x10mm

Fuel Tube d2xD4x4mm

Horn

Clevis

Pushrod

Ø1.4x655mm

PM2x8mm

Ø 2.1mm

Collar

1.5mm

PA3x12mm

3mm

Set Screw

Ø1mm pilot holes for The Wings Maker horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

≈175mm

≈40mm

9

Rudder Pushrod

PB2x10mm

Screw

2

TWM PL8210010

CLEVIS WRENCH

Ø1mm pilot holes for The Wings Maker horn are pre-drilled.

Please look for pin-hole marks at side of control surfaces.

Pushrod

Ø1.4x655mm

Clevis

Horn

≈40mm

≈175mm

Fuel Tube d2xD4x4mm

PB2x10mm

GA029PO22471104

P.5

10A

Engine

This step is for engine powered. Please follow step 10B if your model is electric powered.

To complete your Wingman ll (nitro powered), you need to purchase The Wings Maker

GA029GPTS.

Apply thread locker to screws.

Blind nuts are off-centered to keep the spinner at the fuselge axis.

Optional parts for nitro powered

Wingman lI, GA029GPTS.

GA029GPTS

M3x20mm d3xD7mm

Washer

Fuel Tank

320cc

Plastic Tube d2xD3x180mm

Pushwire

Ø 1.2x370mm

M3

Nut

3.2mm

GA029PO22471104

M3x25mm

Engine Mount

PL5111030

UP

Bottom View

Install Balsa 8x8x76mm

(For Fuel Tank Position Fixing)

Fuel Tank

320cc

Installed Engine Position

105 mm

3.94 in d3xD7mm

Washer

Throttle Servo

Throttle Pushwire

Ø1.4x655mm

d3xD7mm

Washer

Plastic Tube d2xD3x240mm

P.6

Spinner

Ø52mm

Bottom View

10B

Electric

If you want to use electric powered, please follw this step.

M2.5x12mm

GA029EPTS

To Complete your

Wingman lI (electric powered), you need to purchase The

Wings Maker

GA029EPTS.

M3x8mm d3xD7mm

Washer

Battery Tie

GA029PO22471104

Double-Sided

Tape

40A Brushless ESC

M3x12mm d3xD7mm

Washer

Spinner

Ø52mm

Completed

P.7

M6

NUT

Bottom View

11

Radio Equipment

A

Engine Powered

Front

Install and arrange the servos as shown in the diagram.

Straper

Throttle Servo

Rudder Servo

Charge Receptacles

KP0041300 Receiver

Sponge w/ Plastic Tube d2xD3x240mm

B

Electric Powered

Front

Throttle Pushwire

Ø1.4x655mm

Fuel Tube d2xD4x4mm

Elevator Servo

Bottom View

Rudder Servo

Fuel Tube d2xD4x4mm

Battery

Battery

Receiver

Sponge

Straper

Bottom View

Elevator Servo

12

Fuselage Cover

PM2x10mm

Screw

2 d2xD5mm

Washer

2

M2 Nylon Insert Lock Nut

2

PM2x10mm d2xD5mm

Mounting Plate

PM2x10mm d2xD5mm

2mm

Plywood 2x67.5x94.3mm

M2 Nylon Insert Lock Nut

2mm

Plywood 2x67.4x133mm

M2 Nylon Insert Lock Nut

Bottom View

GA029PO22471104

P.8

13

Main Wing

HM3x25mm

Screw

2 d3xD7mm

Washer

2 d3xD7mm

Washer

3mm

HM3x25mm

Plastic Plate 1x15x80mm d3xD7mm

Washer

14

Canopy

PWA2.3x8mm

Screw

4

PM3x25mm

Bottom View

1mm

GA029PO22471104

P.9

15

Wing Setting

Adjust the wing and fuselage configuration as shown in the diagrams.

B

A A’

B’

C

D D’

C’

16

Control Throws

Rudder

Elevator

Ailerons

A=A' B=B' C=C' D=D'

20mm

20mm

Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference.

15mm

15mm

6mm

6mm

GA029PO22471104

P.10

17

C.G.

The ideal C.G. position is 76mm (3 in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.

76 mm

3 in

C.G.

Warning!

Important Safety Precautions

# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.

# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.

Wingman ll

2C 0.40 engine or 450W motor system.

# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running

propeller. Extreme caution should be exercised when working with electric powered models. Make sure the

propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure

you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you

plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental

movement of the throttle stick will spin the propeller and could cause injuries.

# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.

Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.

Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the glue

and shrink the covering at the same time, causing the seams to pull away.

# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

GA029PO22471104

P.11

LINKAGE CONNECTOR

HW7111050 & HW7111060

Drill 2mm hole at servo horn.

Insert linkage connector into servo horn.

Shoulder

Make sure shoulder of screw is cleared from servo horn.

Add washer to reduce play if necessary.

Tighten up the round nut against the shoulder. Apply

CA or permanent thread locker.

After fastening the round nut, make sure that the linkage connector can rotate freely.

GA029PO22471104

KM0374810

Optional Parts

( ACCESSORIES)

37/ 48 Deluxe Fuel Filler

Code No.

Size Package

PL8110030

15 x 22 x 49mm 1 x 1 pc

13860

770

450

8.5-18

30

38

34

37.2

48.5

172

21

5

(Front) and M2.5 (Back)

25mm (Front) and 15.5mm (Back)

40A Brushless ESC

KC2040A02 55x28x12mm

40

33

3

6 ~ 21V

55

Charge Receptacles

Code No.

Size

KP0041300

Package

GA029PO22471104

Clevis Wrench

Code No.

PL8210010

Size

Small Clevis Large Clevis

Special tool for clevis installation.

Suitable for standard and small

(EP) clevis.

Standard Servo

Code No SV4031

Package

1 set

Speed : 0.17 sec / 60° @4.8V

0.14 sec / 60° @6.0V

Torque : 3.2kg.cm / 44.8 oz - in @4.8V

4.1kg.cm / 57.4 oz - in @6.0V

Size : 40.6 x 20 x 37mm /

1.60 x 0.79 x 1.46 in

Weight : 39.4 g / 1.39 oz

Field Stand

Code No.

Size Package

MS9111430 600 x 240 x 310mm

1 pc

GA029PO22471104

www. thewingsmaker.com

GA029PO22471104

THE WINGS MAKER