HiLook Series
2MP ColorVu Audio Fixed
Turret & Bullet Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Model
Type I
THC-T129-PS
Type II
THC-T129-MS
Type III
THC-T229-MS
Type IV
Type V
THC-B129-PS
THC-B129-MS
THC-B229-MS
This manual may contain several technical mistakes or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.
01010020241009
About this Document
This Document includes instructions for using and
managing the Product. Pictures, charts, images
and all other information hereinafter are for
description and explanation only.
The information contained in the Document is
subject to change, without notice, due to
firmware updates or other reasons. Please find
the latest version of the Document at the
Hikvision website (https://www.hikvision.com).
Unless otherwise agreed, Hangzhou Hikvision
Digital Technology Co., Ltd. or its affiliates
(hereinafter referred to as "Hikvision") makes no
warranties, express or implied.
Please use the Document with the guidance and
assistance of professionals trained in supporting
the Product.
About this Product
This product can only enjoy the after-sales service
support in the country or region where the purchase
is made.
Acknowledgment of Intellectual Property
Rights
Hikvision owns the copyrights and/or patents
related to the technology embodied in the
Products described in this Document, which may
include licenses obtained from third parties.
Any part of the Document, including text, pictures,
graphics, etc., belongs to Hikvision. No part of this
Document may be excerpted, copied, translated,
or modified in whole or in part by any means
without written permission.
and other Hikvision’s trademarks and logos
are the properties of Hikvision in various
jurisdictions.
Other trademarks and logos mentioned are the
properties of their respective owners.
LEGAL DISCLAIMER
TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, THIS DOCUMENT AND THE
PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, ARE PROVIDED "AS
IS" AND "WITH ALL FAULTS AND ERRORS".
HIKVISION MAKES NO WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, OR
FITNESS FOR A PARTICULAR PURPOSE. THE USE
OF THE PRODUCT BY YOU IS AT YOUR OWN RISK.
IN NO EVENT WILL HIKVISION BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL,
OR INDIRECT DAMAGES, INCLUDING, AMONG
OTHERS, DAMAGES FOR LOSS OF BUSINESS
PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
DATA, CORRUPTION OF SYSTEMS, OR LOSS OF
DOCUMENTATION, WHETHER BASED ON BREACH
OF CONTRACT, TORT (INCLUDING NEGLIGENCE),
PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OF THE PRODUCT,
EVEN IF HIKVISION HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE
INTERNET PROVIDES FOR INHERENT SECURITY
RISKS, AND HIKVISION SHALL NOT TAKE ANY
RESPONSIBILITIES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES
RESULTING FROM CYBER-ATTACK, HACKER
ATTACK, VIRUS INFECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF
REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE
WITH ALL APPLICABLE LAWS, AND YOU ARE
SOLELY RESPONSIBLE FOR ENSURING THAT YOUR
USE CONFORMS TO THE APPLICABLE LAW.
ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING
THIS PRODUCT IN A MANNER THAT DOES NOT
INFRINGE ON THE RIGHTS OF THIRD PARTIES,
INCLUDING WITHOUT LIMITATION, RIGHTS OF
PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR
DATA PROTECTION AND OTHER PRIVACY RIGHTS.
YOU SHALL NOT USE THIS PRODUCT FOR ANY
PROHIBITED END-USES, INCLUDING THE
DEVELOPMENT OR PRODUCTION OF WEAPONS
OF MASS DESTRUCTION, THE DEVELOPMENT OR
PRODUCTION OF CHEMICAL OR BIOLOGICAL
WEAPONS, ANY ACTIVITIES IN THE CONTEXT
RELATED TO ANY NUCLEAR EXPLOSIVE OR
UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT
OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS
DOCUMENT AND THE APPLICABLE LAW, THE
LATTER PREVAILS.
© Hangzhou Hikvision Digital Technology Co., Ltd. All
rights reserved.
Regulatory Information
FCC Information
Please take attention that changes or modification not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European
standards listed under the Directive 2014/30/EU
(EMCD), Directive 2014/35/EU (LVD) and Directive
2011/65/EU (RoHS).
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a
battery that cannot be disposed of as
unsorted municipal waste in the European
Union. See the product documentation for
specific battery information. The battery is
marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery
to your supplier or to a designated collection point. For
more information, see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
Warning
This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
Safety Instruction
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property
loss.
The precaution measure is divided into “Warnings” and
“Cautions”.
Warnings: Serious injury or death may occur if any of
the warnings are neglected.
Cautions: Injury or equipment damage may occur if any
of the cautions are neglected.
Warnings Follow
these safeguards to
prevent serious injury
or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
Warnings
In the use of the device, you must be in strict
compliance with the electrical safety regulations of
the nation and region.
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12
VDC according to the IEC60950-1 standard and
IEC62368-1 standard. Refer to technical specifications
for detailed information.
Do not connect multiple devices to one power
adapter to avoid over-heating or a fire hazard caused
by overload.
Make sure that the plug is firmly connected to the
power socket.
Make sure that the device is firmly fixed if wall
mounting or ceiling mounting is adopted.
If smoke, odor or noise rise from the device, turn off
the power at once and unplug the power cord, and
then contact the service center.
Never attempt to disassemble the camera by
unprofessional personal.
Cautions
Do not drop the camera or subject it to physical
shock.
Do not touch senor modules with fingers.
Do not place the camera in extremely hot, cold (the
operating temperature shall be -40°C to 60°C), dusty
or damp locations, and do not expose it to high
electromagnetic radiation.
If cleaning is necessary, use clean cloth with a bit of
ethanol and wipe it gently.
Do not aim the camera at the sun or extra bright
places.
The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure that
the surface of sensor will not be exposed to the laser
beam.
Do not expose the device to high electromagnetic
radiation or extremely hot, cold, dusty or damp
environment.
To avoid heat accumulation, good ventilation is
required for the operating environment.
Keep the camera away from liquid while in use for
non-water-proof device.
While in delivery, the camera shall be packed in its
original packing, or packing of the same texture.
The beam of the light at the distance of 200 mm is
classified as Risk Group 1 (RG1). Possible hazardous
optical radiation emitted from this product.
DO NOT stare at operating light source. May be
harmful to the eyes.
Wear appropriate eye protection or turn on the
supplement light only at a safe distance (0.3 m) or in
the area that is not directly exposed to the light when
installing or maintaining the device.
Mark Description
Table 0-1 Mark Description
Mark
Description
DC Voltage
1 Introduction
1.1 Product Features
The main features are as follows:
High performance CMOS sensor
Smart light
4 in 1 video output
1.2 Overview
1.2.1 Overview of Type I Camera
Mounting Base
Switch Button
Power Cord
Video Cable
Microphone
DC12VIN
Main Body
Lens
Enclosure
Figure 1-1 Overview of Type I Camera
Note:
Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs
are available: TVI, AHD, CVI, and CVBS.
1.2.2 Overview of Type II Camera
Screw
Clip Plate
Mounting Base
Trim Ring
Enclosure
Microphone
Main Body
Switch Button
Power Cord
Video Cable
Figure 1-2 Overview of Type II Camera
INDC12V
Note:
Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs
are available: TVI, AHD, CVI, and CVBS.
1.2.3 Overview of Type III Camera
Trim Ring
Enclosure
Microphone
Main Body
Switch Button
Power Cord
Video Cable
INDC12V
Mounting
Base
Figure 1-3 Overview of Type III Camera
Note:
Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs
are available: TVI, AHD, CVI, and CVBS.
1.2.4 Overview of Type IV Camera
IN DC12V
Lens
Bracket
Main Body
Microphone
Switch Button
Power Cord
Video Cable
Figure 1-4 Overview of Type IV Camera
Note:
Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs
are available: TVI, AHD, CVI, and CVBS.
1.2.5 Overview of Type V Camera
Microphone
Lens
Bracket
Main Body
Switch Button
Power Cord
Video Cable
Figure 1-5 Overview of Type V Camera
Note:
Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs
are available: TVI, AHD, CVI, and CVBS.
2 Installation
Before you start
Make sure that the device in the package is in good
condition and all the assembly parts are included.
Make sure that all the related equipment is power-off
during the installation.
Check the specification of the products for the
installation environment.
Check whether the power supply is matched with
your power output to avoid damage.
Make sure the wall is strong enough to withstand
three times the weight of the camera and the mount.
If the product does not function properly, contact
your dealer or the nearest service center. Do NOT
disassemble the camera for repair or maintenance by
yourself.
2.1 Installation of Type I Camera
2.1.1 Ceiling Mounting Without Junction Box
Steps:
1. Rotate the camera to align one of the marks with
the notch, and dissemble the camera.
Mark
Notch
Figure 2-1 Align the Mark and the Notch
2. Pry the enclosure open with a flat object, for
example, a coin, to dissemble the camera.
Figure 2-2 Dissemble the Camera
3. Paste the drill template (supplied) to the place
where you want to install the camera.
4. (Optional) For cement ceiling, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
Figure 2-3 Drill Template
5. (Optional) Drill the cable hole, when the cables are
routed through the ceiling.
6. Use two PA4 screws (supplied) to secure the
mounting base to the ceiling.
Figure 2-4 Secure the Base to the Ceiling
7. Install the camera back to the mounting base and
secure it.
Figure 2-5 Install the Camera Back
8. Connect the power cord and video cable.
9. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle. If
not, adjust the camera according to the figure
below.
Pan Position
[0° to 360°]
Tilt Position
[0° to 75°]
Rotation Position
[0° to 360°]
Figure 2-6 3-Axis Adjustment
1). Rotate the enclosure to adjust the pan position
[0° to 360°].
2). Move the main body up and down to adjust the
tilt position [0° to 75°].
3). Rotate the main body to adjust the rotation
position [0° to 360°].
2.1.2 Ceiling Mounting with Junction Box
Before you start:
You need to purchase a junction box in advance.
Steps:
1. Loosen screws to take apart the junction box.
2. Paste the drill template for junction box to the place
where you want to install the camera.
3. (Optional) For cement ceiling, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
Figure 2-7 Drill Template for Junction Box
4. (Optional) Drill the cable hole, when the cables are
routed through the ceiling.
5. Secure the junction box body on the ceiling with
three PA4 × 25 screws that come with the junction
box.
Figure 2-8 Secure the Junction Box Body
6. Fix the mounting base onto the junction box cover
with two M4 × 10 screws.
Figure 2-9 Fix the Mounting Base
7. Route the cables through the bottom cable hole or
the side cable hole of the junction box.
8. Combine the junction box cover with its body and
secure it with three M3 screws.
Figure 2-10 Combine the Junction Box Cover and Body
9. Connect the power cord and video cable and put
the cables back into the junction box.
10. Refer to step 9 of 2.1.1 Ceiling Mounting Without
Junction Box to adjust the angle and finish the
installation.
2.1.3 Wall Mounting
Before you start:
You need to purchase a wall mount in advance.
Steps:
1. Drill Φ 10 mm screw holes in the wall where you
want to install the wall mount.
2. Use four M6 expansion bolts to fix the wall mount
onto the wall.
Figure 2-11 Fix the Wall Mount
3. Refer to steps 1 and 2 of 2.1.1 Ceiling Mounting
Without Junction Box to dissemble the camera.
4. Use two M4 screws to fix the mounting base onto
the wall mount.
Figure 2-12 Fix the Mounting Base onto the Wall Mount
5. Refer to steps 7 to 9 of 2.1.1 Ceiling Mounting
Without Junction Box to finish the installation.
Figure 2-13 Finish the Installation
2.2 Installation of Type II Camera
2.2.4 Ceiling Mounting Without Junction Box
Steps:
1. Paste the drill template (supplied) to the place
where you want to install the camera.
2. (Optional) For cement ceiling, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
Figure 2-14 Drill Template
3. Loosen the screw and pull out the clip plate to
dissemble the camera.
Figure 2-15 Dissemble the Camera
4. Secure the mounting base to the ceiling with three
PA4 × 25 screws.
Figure 2-16 Attach the Gang Box to the Ceiling
5. Pull out the clip plate and install the camera back to
the mounting base. Push the clip plate back in to
secure the camera.
Figure 2-17 Install the Camera
6. Connect the power cord and video cable.
7. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle. If
not, adjust the camera according to the figure
below.
Pan Position
[0° to 360°]
Tilt Position
[0° to 75°]
Rotation Position
[0° to 360°]
Figure 2-18 3-Axis Adjustment
4). Rotate the enclosure to adjust the pan position
[0° to 360°].
5). Move the main body up and down to adjust the
tilt position [0° to 75°].
6). Rotate the main body to adjust the rotation
position [0° to 360°].
8. Tighten the screw to finish the installation.
2.2.5 Ceiling Mounting with Junction Box
Before you start:
You need to purchase a junction box in advance.
Steps:
1. Paste the drill template for junction box to the place
where you want to install the camera.
2. (Optional) For cement ceiling, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
Figure 2-19 Drill Template
3. (Optional) Drill the cable hole, when the cables are
routed through the ceiling.
4. Take apart the junction box.
5. Secure the junction box body on the ceiling with PA4
× 25 screws that come with the junction box.
Figure 2-20 Secure the Junction Box Body
6. Route the cables through the bottom cable hole or
the side cable hole of the junction box.
7. Combine the junction box cover with its body and
secure it with three PM3 screws.
Figure 2-21 Combine the Junction Box Cover and Body
8. Fix the mounting base onto the junction box with
three M4 × 10 screws.
9. Connect the power cord and video cable and put
the cables back into the junction box.
10. Refer to steps 5, 7, and 8 of 2.2.4 Ceiling Mounting
Without Junction Box to finish the installation.
2.2.6 Wall Mounting
Before you start:
You need to purchase a wall mount in advance.
Steps:
1. Drill Φ 10 mm screw holes in the wall where you
want to install the wall mount.
2. Use four M6 expansion bolts to fix the wall mount
onto the wall.
Figure 2-22 Fix the Wall Mount
3. Loosen the screw and pull out the clip plate to
dissemble the camera.
Figure 2-23 Dissemble the Camera
4. Use three M4 screws to fix the mounting base onto
the wall mount.
Figure 2-24 Fix the Mounting Base onto the Wall Mount
5. Refer to steps 5 to 8 of 2.2.4 Ceiling Mounting
Without Junction Box to finish the installation.
Figure 2-25 Finish the Installation
2.3 Installation of Type III Camera
2.3.1 Ceiling Mounting Without Junction Box
Steps:
1. Paste the drill template (supplied) to the place
where you want to install the camera.
2. (Optional) For cement ceiling, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
Figure 2-26 Drill Template
3. (Optional) Drill the cable hole, when the cables are
routed through the ceiling.
4. Turn the trim ring counterclockwise to remove it
from the camera.
Figure 2-27 Remove the Trim Ring
5. Secure the camera to the ceiling with three PA4 × 25
screws (supplied).
Figure 2-28 Secure the Camera to the Ceiling
6. Connect the power cord and video cable.
7. Loosen the screw and the clip plate.
Figure 2-29 Loosen the Screw and Clip Plate
8. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle. If
not, adjust the camera according to the figure
below.
Pan Position
[0° to 360°]
Tilt Position
[0° to 75°]
Rotation Position
[0° to 360°]
Figure 2-30 3-Axis Adjustment
1). Rotate the enclosure to adjust the pan position
[0° to 360°].
2). Move the main body up and down to adjust the
tilt position [0° to 75°].
3). Rotate the main body to adjust the rotation
position [0° to 360°].
9. Fasten the screw and the clip plate.
10. Install the trim ring back.
Figure 2-31 Install the Trim Ring Back
11. Turn the trim ring clockwise to secure the camera.
Figure 2-32 Secure the Camera
2.3.2 Installation with Junction Box/Inclined Ceiling
Mount
Before you start:
You need to purchase a junction box or inclined
ceiling mount in advance.
Ceiling mounting with junction box and inclined
ceiling mount are similar. Following steps take
junction box as an example.
Steps:
1. Paste the drill template for junction box to the place
where you want to install the camera.
2. (Optional) For cement wall, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
Figure 2-33 Drill Template
3. (Optional) Drill the cable hole, when the cables are
routed through the wall.
4. Turn the trim ring counterclockwise to remove it
from the camera.
Figure 2-34 Remove the Trim Ring
5. Take apart the junction box.
6. Fix the camera onto the junction box cover with
three PM4 × 10 screws.
Figure 2-35 Fix the Camera onto Junction Box Cover
7. Secure the junction box body on the wall with four
PA4 × 25 screws.
Figure 2-36 Secure the Junction Box Body
8. Route the cables through the bottom cable hole or
the side cable hole of the junction box and connect
the cables.
9. Combine the junction box cover with its body with
the four screw on the cover.
Figure 2-37 Combine Junction Box Cover with Body
10. Refer to steps 7 and 11 of 2.3.1 Ceiling Mounting
Without Junction Box to adjust the angle and finish
installation.
2.3.3 Wall Mounting
Before you start:
You need to purchase a wall mount in advance.
Steps:
1. Drill Φ 10 mm screw holes in the wall where you
want to install the wall mount.
2. Use four M6 expansion bolts to fix the wall mount
onto the wall.
Figure 2-38 Fix the Wall Mount
3. Turn the trim ring counterclockwise to remove it
from the camera.
Figure 2-39 Remove the Trim Ring
4. Install the camera to the wall mount with three PA4
× 25 screws (supplied).
Figure 2-40 Install the Camera
5. Refer to steps 6 to 11 of 2.3.1 Ceiling Mounting
Without Junction Box to finish installation.
2.4 Installation of Type IV Camera
2.4.1 Ceiling/Wall Mounting Without Junction Box
Before you start:
The ceiling mounting and wall mounting are similar.
Following steps take ceiling mounting as an example.
Steps:
1. Paste the drill template (supplied) to the place
where you want to install the camera.
2. (Optional) For cement ceiling, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
Scre w Hole
Cable
Hole
Scre w Hole
Scre w Hole
tem pl ate
Side Opening
Figure 2-41 Drill Template
3. (Optional) Drill the cable hole, when the cables are
routed through the ceiling.
4. Align the screw holes in the bracket to the ceiling,
and secure the camera with three PA4 × 25 screws
(supplied).
Figure 2-42 Secure the Camera to the Ceiling
5. Connect the power cord and video cable.
6. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle. If
not, adjust the camera according to the figure
below.
Pan Position
[0° to 360°]
Rotation Position
[0° to 360°]
Trim Ring
Tilt Position
[0° to 180°]
Screw A
Screw B
Figure 2-43 3-Axis Adjustment
Loosen the trim ring to adjust the pan position
[0° to 360°].
5). Loosen screw A to adjust the tilt position [0° to
180°].
6). Loosen screw B to adjust the rotation position [0°
to 360°].
7. Tighten the trim ring and screws to finish the
installation.
4).
2.4.2 Ceiling/Wall Mounting with Junction Box
Before you start:
You need to purchase a junction box in advance.
Ceiling mounting and wall mounting are similar.
Following steps take wall mounting as an example.
Steps:
1. Paste the drill template for junction box to the place
where you want to install the camera.
2. (Optional) For cement wall, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
Figure 2-44 Drill Template for Junction Box
3. (Optional) Drill the cable hole, when the cables are
routed through the wall.
4. Take apart the junction box.
5. Align the screw holes of the camera with those on
the junction box cover. Attach the camera to the
junction box cover with three PM4 × 10 screws.
Figure 2-45 Attach the Camera to the Junction Box
Cover
6. Secure the junction box body on the wall with three
PA4 × 25 screws (supplied).
Figure 2-46 Secure the Junction Box on the Wall
7. Route the cables through the bottom cable hole or
side cable hole of the junction box and connect the
cables.
8. Fix the junction box cover on its body with three
PM3 × 16 L6 screws that come with the junction
box.
Figure 2-47 Fix the Junction Box Cover on Its
Body
9. Repeat steps 6 to 7 of 2.4.1 Ceiling/Wall Mounting
Without Junction Box to finish the installation.
2.5 Installation of Type V Camera
2.5.1 Ceiling/Wall Mounting Without Junction Box
Before you start:
The ceiling mounting and wall mounting are similar.
Following steps take ceiling mounting as an example.
Steps:
1. Paste the drill template (supplied) to the place
where you want to install the camera.
2. (Optional) For cement ceiling, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
Scre w Hole
Cable
Hole
Scre w Hole
Scre w Hole
tem pl ate
Side Opening
Figure 2-48 Drill Template
3. (Optional) Drill the cable hole, when the cables are
routed through the ceiling.
4. Align the screw holes in the bracket to the ceiling,
and secure the camera with three PA4 × 25 screws
(supplied).
Figure 2-49 Secure the Camera to the Ceiling
5. Connect the power cord and video cable.
6. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle. If
not, adjust the camera according to the figure
below.
Pan Position [0° to 360°]
Trim Ring
Tilt Posi tion [0° to 180°]
Rotation Position
[0° to 360°]
Screw A
Screw B
Figure 2-50 3-Axis Adjustment
Loosen the trim ring to adjust the pan position
[0° to 360°].
2). Loosen screw A to adjust the tilt position [0° to
180°].
3). Loosen screw B to adjust the rotation position [0°
to 360°].
7. Tighten the trim ring and screws to finish the
installation.
1).
2.5.2 Ceiling/Wall Mounting with Junction Box
Installation of type II camera with junction box is similar
with that of type I camera. Refer to 2.4.2 Ceiling/Wall
Mounting with Junction Box for details.
3 Waterproof Measures
If the camera is installed outdoor, you should use the
waterproof tapes to waterproof the cables. Otherwise
the cables might get wet or a short circuit occurs.
Note:
Waterproof tapes should be purchased separately.
After routing and connecting the cables, use the
waterproof tapes to wrap up the cables. Connected
cables and spare cables both should be wrapped up as
the figures below.
Figure 3-1 Waterproof Cables
4 Menu Description
Please follow the steps below to call the menu.
Note:
The actual display may vary with your camera model.
Steps:
1. Connect the camera with the TVI DVR and the
monitor, as shown in figure 3-1.
TVI DVR
Camera
Monitor
Figure 4-1 Connection
2. Power on the camera, TVI DVR, and monitor to view
the image on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking button or
calling preset No. 95.
VIDEO
FORMAT
EXPOSURE MODE
AGC
ANTI- BANDING
EXPOSURE
BACK
EXIT
SAVE & EXIT
IMAGE MODE
WHITE BALANCE
BRIGHTNESS
CONTRAST
VIDEO
SETTINGS
SHARPNESS
SATURATION
3 DNR
BACK
EXIT
SAVE & EXIT
MAIN MENU
LIGHT
SMART
LIGHT
THRESHOLD
LEVEL
BACK
EXIT
SAVE & EXIT
AUDIO
AUDIO
SETTINGS
LEVEL
BACK
EXIT
SAVE & EXIT
FACTORY
DEFAULT
CANCEL
CONFIRM
EXIT
SAVE & EXIT
Figure 4-2 Main Menu Overview
5. Click the direction buttons to control the camera.
1). Click up/down direction buttons to select menu
options.
2). Click Iris + to confirm the selection.
3). Click left/right direction buttons to adjust the
value of the selected option.
4.1 VIDEO FORMAT
You can set the video format to 2MP@25fps,
2MP@30fps, PAL, or NTSC.
4.2 EXPOSURE
EXPOSURE MODE
You can set the EXPOSURE MODE to GLOBAL, BLC, HLC,
or DWDR.
GLOBAL
GLOBAL refers to the normal exposure mode which
adjusts lighting distribution, variations, and
non-standard processing.
BLC (Backlight Compensation)
BLC (Backlight Compensation) compensates light to the
object in the front to make it clear, but this may cause
over-exposure of the background where the light is
strong.
HLC (Highlight Compensation)
HLC stands for highlight compensation. The camera
detects strong spots (over-exposure portion of image)
and reduces the brightness of strong spots to improve
the overall images.
DWDR (Digital Wide Dynamic Range)
Digital wide dynamic range gives the camera the ability
to view dark areas of given image as well as extremely
lighted portions of the image or areas of high contrast.
AGC (Auto Gain Control)
It optimizes the clarity of the image in poor light
conditions. The AGC level can be set to HIGH, MEDIUM,
or LOW.
Note:
The noise will be amplified when setting the AGC level.
ANTI-BANDING
ANTI-BANDING is a camera setting that prevents the
appearance of horizontal lines (banding) when
photographing images in low frequency light and high
brightness environments.
4.3 VIDEO SETTINGS
Move the cursor to VIDEO SETTINGS and click Iris+ to
enter the submenu. IMAGE MODE, WHITE BALANCE,
BRIGHTNESS, CONTRAST, SHARPNESS, SATURATION,
3DNR, and MIRROR are adjustable.
VIDEO SETTINGS
IMAGE MODE
WHITE BALANCE
BRIGHTNESS
CONTRAST
SHARPNESS
SATURATION
3DNR
MIRROR
BACK
EXIT
SAVE & EXIT
STD
5
5
5
5
5
OFF
Figure 4-3 VIDEO SETTINGS
IMAGE MODE
IMAGE MODE is used to adjust the image saturation,
and you can set it to STD (Standard), HIGH-SAT (High
Saturation), or HIGHLIGHT (better indoor facial details).
WHITE BALANCE
White balance, the white rendition function of the
camera, is to adjust the color temperature according to
the environment. It can remove unrealistic color casts in
the image. You can set WHITE BALANCE mode to AUTO
or MANUAL.
AUTO
Under AUTO mode, white balance is being adjusted
automatically according to the color temperature of the
scene illumination.
MANUAL
You can adjust the R-GAIN and B-GAIN value to correct
colors manually.
WHITE BALANCE
MODE
R-GAIN
B-GAIN
BACK
EXIT
SAVE&EXIT
MANUAL
5
5
Figure 4-4 WHITE BALANCE
BRIGHTNESS
Brightness refers to the brightness of the image. You
can set the brightness value from 1 to 9 to darken or
brighten the image. The greater the value is, the
brighter the image is.
CONTRAST
This feature enhances the difference in color and light
between parts of an image.
SHARPNESS
Sharpness determines the amount of detail an imaging
system can reproduce.
SATURATION
Saturation is the proportion of pure chromatic color in
the total color sensation. Adjust this feature to change
the saturation of the color.
3DNR (3D DNR)
3DNR refers to 3D digital noise reduction. Comparing
with the general 2D digital noise reduction, the 3D
digital noise reduction function processes the noise
between two frames besides processing the noise in
one frame. The noise will be much less and the video
will be clearer.
4.4 SMART LIGHT
SMART LIGHT is used to control the integrated white
light and avoid overexposure when the light is on. You
can set the light as AUTO or OFF.
SMART LIGHT
LIGHT
THRESHOLD
LEVEL
BACK
EXIT
SAVE & EXIT
AUTO
2
5
Figure 4-5 SMART LIGHT
AUTO
Under the AUTO mode, the white light turns on
automatically as the environment becomes dark.
The THRESHOLD is the environmental light level at
which the white light turns on. The greater the value is,
the darker the environment is when the light is
activated.
The value of LEVEL controls the brightness of the white
light. The greater the value is, the brighter the light is.
OFF
The white light is always off except when alarm is set
and triggered.
4.5 AUDIO SETTINGS
Under the AUTO SETTINGS sub-menu, you can set the
mode to ON or OFF. Adjust the LEVEL to a higher value
to raise the volume.
AUDIO SETTINGS
AUDIO
LEVEL
BACK
EXIT
SAVE&EXIT
ON
2
Figure 4-6 AUTO SETTINGS
4.6 FACTORY DEFAULT
Click CANCEL to back to the main menu.
Click CONFIRM to reset all the settings to factory
defaults.
4.7 EXIT
Move the cursor to EXIT and click Iris+ to exit the menu.
4.8 SAVE & EXIT
Move the cursor to SAVE & EXIT and click Iris+ to save
the settings and exit the menu.
UD29286B-A
">
